Sonance ASAP3D SE User Manual

SONANCE

SONAMP® ASAP3D SE

Features:

IR commands for volume, mute, input switching and BBE

ICEpower® digital ampliﬁer is highly efﬁcient, generating very little heat and keeping the ampliﬁer’s size to a minimum, both of which greatly expand installation options.

BBE Sound Enhancement improves speaker presence and detail

SONAMP® ASAP3D SE

Stereo Power Ampliﬁer

The ASAP3D SE combines the latest digital power ampliﬁer technology from Bang & Olufsen with proven Sonamp auto House/ Local source switching and BBE Sound Enhancement in a new small package that dramatically expands your installation options.

The ASAP3D SE will automatically switch a pair of speakers between two different input sources (House and Local). Typically the House source will be a whole-home audio system that normally plays in the area and the Local Source will be a nearby source, such as a TV set or iPort™. A common application would be to use the ASAP3D SE to power and automatically switch a pair of speakers in a bedroom from playing background music sent by the whole-home audio system to playing the sound of the bedroom TV whenever the TV is switched on. With the ampliﬁer’s Mono Variable Output feeding a local-zone powered subwoofer, this installation would provide much better sound quality than the TV could supply on its own.

IR commands for volume, mute, input switching, and BBE, greatly enhance ﬂexibility and can be directly controlled by a wholehome control system or an IR keypad controller. The IR output allows connections to OptiLinQ signals can be passed through to their intended components and the IR bus connection allows IR signals from multiple ASAP3D SE’s to be passed through to a single set of IR emitters.

Features

Any on of four different triggers can be set to cause the ASAP3D SE to automatically switch from the House Source to the Local Source:

• When an audio signal is present at the Local line or Local speaker inputs;

• When a TV set is connected to the ASAP3D SE’s AC Trigger outlet is turned ON;

• When an external control voltage is present at the Voltage Trigger input;

• When triggered by a signal from an IR controller connected to the IR input.

IR emitters so that 3rd-party control

Small form factor allows multiple installation options (back of a ﬂat panel TV, wall behind a ﬂat panel TV, rack, etc)

Speciﬁcations

ASAP3D SE Stereo Power Ampliﬁer

Number of Channels: 2 (one stereo pair) Output Power (Stereo): 25 watts RMS per channel, 0.25% THD, 20Hz – 20kHz, @ 8 ohms 50 watts RMS per channel, 0.25% THD, 1kHz, @ 4 ohms Frequency Response: 20Hz – 20kHz +1dB/–3dB (w/20Hz high-pass ﬁlter) Total Harmonic Distortion: 0.10% (1kHz, 8 ohms); 0.25% (1kHz, 4 ohms) Signal to Noise Ratio: -94dB (w/22kHz ﬁlter, A-WTD);

-88dB (with AC-sensing trigger) Input Sensitivity: 0.9V for 25W RMS output

0.7V w/BBE ON (+3dB)

0.5V w/BBE ON (+6dB)

Input Impedance: 13k ohms Maximum Source Input Voltage: 2.3VAC RMS

1.3VAC RMS w/BBE ON Power Consumption: 200 watts Heat Output: 187 BTU/hr AC Fuse: 120V Version: 2A (T2AL ~ 250V) 230V Version: 1.25A (T1.25AL ~250V) Dimensions (W x H x D): 9½” x 1¾” x 12½” (241mm x 45mm x 318mm) Rack Space Requirements: 1U (½-rack width) Weight: 7.0 lbs (3.2kg)

Sonance

212 Avenida Fabricante San Clemente, CA 92672-7531 USA, 1.800.582.7777 sonance.com

©2008 Sonance, All Rights Reserved. Sonance, Sonamp and OptiLinQ are registered trademarks of Dana Innovations. iPort is a trademark of Dana Innovations. BBE is a registered trademark of BBE Sound, Inc. ICEpower is a registered trademark of Bang & Olufsen. Due to continuous product improvement, all features and speciﬁcations are subject to change without notice. For the latest Sonance product information, go to: www.sonance.com

33-5051