www.somfysystems.com
Ondeis™ WireFree RTS
Rain & Sun Sensor
EN
Installer Manual
www.somfysystems.com
SOMFY SYSTEMS INC
SOMFY NORTH AMERICAN HEADQUARTERS
121 Herrod Blvd.
Dayton, NJ 08810
P: (800) 22-SOMFY (76639)
NJ: (609) 395-1300
F: (609) 395-1776
FLORIDA
6100 Broken Sound Pkwy. N.W.
Suite 14
Boca Raton, FL 33487
P: (800) 22-SOMFY (76639)
F: (561) 995-7502
CALIFORNIA
15291 Barranca Parkway
Irvine, CA 92618-2201
P: (800) 22-SOMFY (76639)
F: (949) 727-3775
SOMFY ULC
SOMFY Canada Division
5178 Everest Drive
Mississauga, Ontario L4W2R4
P: (800) 66-SOMFY (76639)
CN: (905) 564-6446
F: (905) 238-1491
Copyright © 5/2015 Somfy Systems Inc./SAS. All rights reserved.
Ondeis™ WireFree RTS
Rain & Sun Sensor Overview
.
Works with all Radio Technology Somfy® (RTS)
exterior motors and Universal RTS Receiver
.
Single channel combination rain and sun sensor
.
Solar powered rechargeable battery
.
Adjustable rain and sun thresholds
.
Six different operation modes, Demo mode
.
Flexible installation options
.
Status LEDs for visual feedback
.
Rain commands always take priority
.
Operational temperature: 32˚F/0˚C to 140˚F/60˚C
IP Rating: IP55
What is in the box:
1. Ondeis™ WireFree RTS Rain & Sun Sensor
with a mounting plate and 2 round head wood screws
2. Gutter mount:
.
1 Aluminum gutter-mount bracket
.
2 Socket head screws
.
2 Flat head screws
.
2 Nylon locking nuts
Optical Rain Sensor
Sun Sensor
Solar Charging Panel
Rain Sensor LED
Hatch
LED Behavior
Normal Operation
.
Blinks every 5 seconds when conditions are above
the threshold
Demo Mode
.
Alternate blinks when entering demo mode
.
Blinks continuously when conditions are above the
threshold
.
Blink together when exiting demo mode
Mounting Plate
Sun sensor LED
GETTING STARTED
Hatch Label
Rain Threshold
Dial
Demo Button
Configuration Switches
Switch Sticker
Sun
Threshold
Dial
Programming
Button
1) Charge the sensor.
a. 10 minutes in direct sunlight will
provide operation charge.
b. For most efficient charging, open
hatch and move all switches to the OFF
position.
2) Confirm
RTS motorized window coverings are
operating properly from an RTS control. The UP
command should send the awnings IN and screens/
shutters UP.
(To change the direction please follow the awning
instructions)
3) Choose sensor operation mode.
The default
setting is Awning Rain. For detailed explanations of
operation modes, refer to Operation Modes on reverse.
NOTE: A Soliris transmitter (1810647 or 1811243 –
not included) is required for Awning Sun and Awning
Rain & Sun operation modes.
4) Select sensor threshold settings
a.
Factory Default:
.
Rain: 9 o’clock (arrow pointing left)
.
Sun: 12 o’clock (arrow pointing up)
Approx 9:00
Light Rain
b.
More sensitive:
.
Very light rain/heavy mist/heavy condensation
.
Heavy cloud cover (.5 klux)
c.
Less sensitive:
.
Very heavy rain
.
Direct summer sun, no cloud cover (55 klux)
turn left
turn right
Approx 12:00
Facing Sun, Light Cloud Cover
5) Program the sensor to the motor(s)
Step 1: Press the programming button on
the RTS transmitter to put the motor into
programming mode – motor will jog.
Step 2: Press the sensor’s programming
button – motor will jog again.
Deleting the sensor -
above.
6) To confirm settings
mode to test rain/sun sensing without standard
wait times.
a. Briefly press and release “Demo” button. The
associated motor(s) will jog and the sensor’s LEDs
will alternate blinks.
b. Demo mode will time out after 2 minutes. To
exit demo mode, press the Demo button again.
SENSOR TIME DELAYS
Rain present 0 sec (UP-Locked) 0 sec (UP-Locked)
Rain absent 3 sec (Unlocked) 5 min (Unlocked)
Sun present 10 sec (DOWN) 2 min (DOWN)
Sun absent 15 sec (UP) 15-30 min (UP)
7) Mount the sensor
to rain and/or sun.
a. For best sun protection, sensor should be
mounted facing same direction as the associated
motorized window coverings.
b. For best rain protection, sensor should be
exposed to as much rain as possible.
c. There are three different mounting options
possible using included mounting plate and
bracket: vertical mount, pole mount (using zip
ties, not included) and gutter mount.
Pole and Wall Mount
Repeat steps 1 and 2
, put sensor into demo
DEMO Mode Normal Mode
for maximum exposure
7) Mount the sensor
.
The mounting bracket is released by pushing
the bracket clips down gently towards the
main body of the sensor and sliding out the
mounting bracket.
.
To replace the mounting bracket, press the
bracket clips down gently towards the main
body of the sensor and slide in the mounting
bracket, making sure the front tabs move into
the top slot and the back tabs into the lower
slot.
NOTE: The sensor does NOT operate under 32˚F/0˚C;
standing water, snow or frost DOES NOT activate
sensor.
Gutter Mount
(continued)
OPERATION MODES
Important: A programmed sensor must be deleted from the motor’s memory before it is changed between Awning or Shutter/Screen mode. Do not change between Awning
and Shutter/Screen modes without deleting the sensor from the motor’s memory first (to delete the sensor see step 5).
Awning Modes
A. Awning Rain (factory default)
NOTE: Standing water, snow or frost DOES NOT lock the
sensor
B. Awning Sun
NOTE: A Soliris transmitter (1810647 or 1811243 – not
included) is required to activate the motor’s sun function.
C. Awning Rain & Sun
NOTE: A Soliris transmitter (1810647 or 1811243 – not
included) is required to activate the motor’s sun function
(Sensor Modes):
.
Rain over threshold: sends awning in
.
Awning is locked until 5 minutes after last rain over
threshold detected
.
.
Sun over threshold (for 2 minutes): sends awning out
.
Sun under threshold (for 15-30 minutes): sends
awning in
.
Rain over threshold: sends awning in
.
Awning is locked until 5 minutes after last rain over
threshold detected, even to Sun commands
.
Sun over threshold (for 2 minutes): sends awning out
.
Rain & Sun over threshold: sends awning in
.
Rain & Sun under threshold (for 15-30 minutes):
sends awning in
Shutter/Screen Modes
Remove switch sticker to access shutter settings
E. Shutter/Screen Rain
.
.
.
F. Shutter/Screen Rain & Sun
.
.
.
.
G. Shutter/Screen Rain & Auto Up
.
.
.
(Transmitter Modes):
Rain over threshold: sends shutters/screens down
Rain doesn’t lock the motor – transmitter commands
will still work.
Will not send another command until rain falls below
the threshold for 5 min and then goes above again
Rain over threshold: sends shutters/screens down
Shutter/screen will lock out sun commands until 5
minutes after last rain over threshold is detected;
transmitter commands will still work
Sun over threshold (for 2 minutes): sends shutters/
screens down
Sun under threshold (for 15 minutes): sends shutters/
screens up
Rain over threshold: sends shutters/screens down
Rain doesn’t lock the motor – transmitter commands
will still work
Rain under threshold (for 5 minutes): sends shutters/
screens up
Securely attach rain sensor mounting plate to
aluminum gutter mount bracket using flat head
screws and nylon locking nuts. Slide gutter
mount bracket over gutter lip and secure with
socket-head screws.
NOTE: If the sensor is removed from a job site,
it must be deleted from the motor’s memory.
If the sensor is removed from the jobsite while
in a sensor mode, the awning will retract at
regular intervals.
The sensor must ALWAYS be deleted from the
motor’s memory before removing from the job
site OR switching between awning and shutter/
screen modes.
D. Awning Sensor Test
Allows testing of the sensor programmed to the
motor. In this mode, pressing the DEMO button
will extend the awning. This mode is for testing
only. Do not leave the unit in this mode for normal
operation.
Non-functional Dip Switch settings. Do not use the following Dip Switch configurations:
This device complies with Part 15 of the FCC Rules. Operation is subject to the following conditions
- This device may not cause harmful interference and
- This device must accept any interference received, including interference that may cause undesired operation
Warning! Changes or modifications not expressly approved by the manufacturer could void the users authority to operate the equipment.
H. Shutter/Screen Transmitter Test
Allows testing of the sensor programmed to the
motor. In this mode, pressing the DEMO button will
send a down transmitter command. This mode is for
testing only. Do not leave the unit in this mode for
normal operation.
Copyright © 5/2015 Somfy Systems Inc./SAS. All rights reserved.