SOMFY INTEO LIGHTING outdoor RTS Installation Manual
inteo LIGHTING outdoor RTS
INSTALLATION
guide
Ref.5004241
■
Main supply : 220-240V ~
■
Class II product
■
Protection index : IP44
■
Load : incandescent or halogen
lamps 500 W max.
■
Radio frequency : 433.42 MHz
■
Operating temp. : -30°C to +80°C
1
Characteristics
2
Installation
Install the LIGHTING outdoor RTS with the cables entry pointing downwards to avoid
water infiltration (wire strip lenght : 6 mm / 0,23 in)
Recommandation of mounting for better radio reception :
minimum distance between LIGHTING outdoor RTS and the floor : 1,5 m.
minimum distance between a LIGHTING outdoor RTS and a radio transmitter : 30 cm.
minimum distance between two LIGHTING outdoor RTS : 20 cm.
Warning : cordless radio equipment (e.g. headphones) in 433MHz can
affect the functionning of the LIGHTING outdoor RTS.
The LIGHTING outdoor RTS is a radio receiver dedicated to control an incandescent or
halogen lamp with an RT or RTS control (no lamp with gear).
Up to twelve different controls can be memorized in the memory of the LIGHTING out-
door RTS allowing individual, group and master commands.
This device must be installed and programmed by qualified installers for whom
this instruction is intended.
3
Programming and operating
3.1 Record the first control
Hereby,SOMFY,declares that this equipment is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC.
A Declaration of Conformity is available at the web
address
www.somfy.com
Heading
CE
N
L
RTS control : press briefly the “prog” button.
RT control : remove the battery, press briefly the button, replace the batte-
ry and press again briefly the button.
➜ The lamp lights during 2 secs. again and the LED of the LIGHTING out-
door RTS blinks during 5 sec. The control has been recorded.
Set the
LIGHTING outdoor RTS in its programming mode : Record the first control :
150 mm
133 mm
150 mm
40 mm
programming
button
manual
control button
LED
POWER
SUPPLY
Phase
Neutral
Phase
Neutral
Output
Do not use
N
X
L
N
L
2 s
➜
Press for more than 2 seconds on the programming button of
the LIGHTING outdoor RTS.
➜ The LED of the LIGHTING outdoor RTS lights on and the
lamp lights for 2 secs.
The LIGHTING outdoor RTSis in programming mode for one
minute.
N
L
N
L
N
L
➜
3V
LITHIUM
RENATA
CR 2032
3V
LITHIUM
RENATA
CR 2032
S
W
I
S
S
M
A
D
E
3V
LITHIUM
RENATA
CR 2032
3V
LITHIUM
RENATA
CR 2032
S
W
I
S
S
M
A
D
E
0,5 s
0,5 s
0,5 s
or
5 s
2 s
2 s
12
3.4 Remove a control
3.5 Complete reset (back to factory configuration)
3.3 Record a new control
3.2 Operating
3V
LITHIUM
RENATA
CR 2430
S
W
I
S
S
M
A
D
E
3V
LITHIUM
RENATA
CR 2430
Note : When you enter in programming mode with an already recorded control, you cannot erase it
➜
or
With a RTS control With a RT control With the built in control button
Press briefly the ▲ button to switch the lamp ON.
Press briefly the ■ or ▼ buttons to switch the lamp OFF.
ON
OFF
ON/OFF
Press briefly on the front button of the RT
control to switch the lamp ON or OFF.
You can also control the lamp with the push button
located on the LIGHTING outdoor RTS.
3
Trouble shooting guide
3V
LITHIUM
RENATA
CR 2032
3V
LITHIUM
RENATA
CR 2032
S
W
I
S
S
M
A
D
E
3V
LITHIUM
RENATA
CR 2032
3V
LITHIUM
RENATA
CR 2032
S
W
I
S
S
M
A
D
E
Nothing works:
ð Check the light.
ð Check the power supply.
ð Check the battery of the transmitter.
ð Check that the transmitter has been properly recorded in the LIGHTING outdoor RTS memory (section 3).
ð Check for any other possible source of radio interferences.
Lost in your programming mode:
ð Just make a complete reset and start again.
0,5 s
0,5 s
0,5 s
or
3V
LITHIUM
RENATA
CR 2430
S
W
I
S
S
M
A
D
E
3V
LITHIUM
RENATA
CR 2430
Press for more than 2 sec. on the programming button of the LIGHTING outdoor
RTS or use an already recorded control.
RTS control : press for more than 2 sec. on the “prog” button.
RT control : remove the battery, press briefly the button, replace the battery and
press for more than 2 sec. on the button.
➜ The LED of the LIGHTING outdoor RTS lights on and the lamp lights for 2 secs.
RTS control : press briefly the “prog” button.
RT control : remove the battery, press briefly the button, replace the
battery and press again briefly the button.
➜ The lamp lights during 2 secs. again and the LED of the LIGHTING
outdoor RTS blinks during 5 sec. The new control is recorded.
RTS control : press briefly the “prog” button.
RT control : remove the battery, press briefly the button, replace the
battery and press again briefly the button.
➜ The lamp lights during 2 secs. again and the LED of the LIGHTING
outdoor RTS blinks during 5 sec. The control has been erased.
1 2
1 2
Set the LIGHTING outdoor RTS in its programming mode :
Record the new control :
Remove the control :
➜
3V
LITHIUM
RENATA
CR 2032
3V
LITHIUM
RENATA
CR 2032
S
W
I
S
S
M
A
D
E
3V
LITHIUM
RENATA
CR 2032
3V
LITHIUM
RENATA
CR 2032
S
W
I
S
S
M
A
D
E
➜
3V
LITHIUM
RENATA
CR 2032
3V
LITHIUM
RENATA
CR 2032
S
W
I
S
S
M
A
D
E
3V
LITHIUM
RENATA
CR 2032
3V
LITHIUM
RENATA
CR 2032
S
W
I
S
S
M
A
D
E
2 s
0,5 s
0,5 s
0,5 s
0,5 s
or
or
2 s
2 s
N
L
N
L
N
L
➜
Press for more than 7 seconds the programming button of the LIGHTING outdoor RTS until the
LED lights.
➜ The LED lights up after 2 seconds and blinks after 7 seconds Then, the lamp lights during 2 secs.
the LIGHTING outdoor RTS has been completely cleared and no more controls are recorded.
You have then to re-program the LIGHTING outdoor RTS from the first step of programming
(refer to the section 3.1 “Record the first control”).
N
L
2 s
already recorded control
or
Press for more than 2 sec. on the programming button of the LIGHTING outdoor
RTS or use an already recorded control.
RTS control : press for more than 2 sec. on the “prog” button.
RT control : remove the battery, press briefly the button, replace the battery and
press for more than 2 sec. on the button.
➜ The LED of the LIGHTING outdoor RTS lights on and the lamp lights for 2 secs.
Set the LIGHTING outdoor RTS in its programming mode :
5 s
2 s
N
L
5 s
2 s
N
L
5 s
ON/OFF
2 s
➜
3V
LITHIUM
RENATA
CR 2032
3V
LITHIUM
RENATA
CR 2032
S
W
I
S
S
M
A
D
E
3V
LITHIUM
RENATA
CR 2032
3V
LITHIUM
RENATA
CR 2032
S
W
I
S
S
M
A
D
E
2 s
0,5 s
or
2 s
N
L
N
L
2 s
already recorded control
or
2 s
N
L
7 s
SOMFY SAS, capital 20.000.000 Euros, RCS Bonneville 303.970.230
All rights reserved to makes changes without prior notice.
Loading...