Somfy INTEO EOLIS RECEIVER RTS 2 INSTALLATION Manual
The EOLIS receiver RTS is a radio receiver for awnings with protection
against wind damage.
The EOLIS receiver RTS is compatible with the EOLIS sensor,all the RTS
controls and the INIS RT.
Commands are transmitted by radio (frequency 433.42 MHz).
With an INIS RT,the functioning of the EOLIS receiver RTS is a trip switch type :
▲, stop, ▼, stop,…
❏ Mains supply : 220-240 V~ 50/60 Hz
❏ Protection index: IP 44
❏ Operating temperature: -20°C to +50°C
❏ Class II product once installed
❏ Normally polluted environment
inteo EOLIS receiver RTS 2
INSTALLATION
guide
Ref.5003510
Characteristics:
Installation:
2
Before connecting the unit, you must read the instructions carefully.
▲ ▼ N N L
SC
Programming
button
LED
Built-in manual
security control
1
Mounting of the EOLIS receiver RTS 2 :
A
Recommendations :
❏ Install the EOLIS receiver RTS with the cables entry pointing downwards
to avoid water infiltration.
❏ Do no install the eolis receiver RTS against a metallic part
(it could affect the radio transmission).
❏ minimum distance between the receiver and the floor : 1,5 m
.
❏ minimum distance between the receiver and the roof : 30 cm
.
❏ minimum distance between the receiver and the transmitter : 30 cm.
❏ minimum distance between two receivers : 20 cm
.
Hereby, SOMFY, declares that this equipment is in
compliance with the essential requirements and
other relevant provisions of Directive 1999/5/EC.
A Declaration of Conformity is available at the web
address
www.somfy.com
Heading
CE
150 mm
150 mm
40 mm
®
Cabling of the EOLIS receiver RTS 2 :
B
The EOLIS receiver RTS is compatible with all standard SOMFY motors. Cabling arrangements are shown in
the diagram. Respect the electrical standards in force as well as the following points:
- disconnect the mains before carrying out any work.
- be careful to avoid static electricity which could damage some electronic components.
- use flexible cables
- ensure that no longitudinal forces act on the cable carriers after installation
- do not forget to connect the earth wires.
Cabling of the EOLIS sensor
RTS control or INIS RT
Wind function :
C
The wind threshold can be adjusted by the potentiometer to accommodate
wind speeds between 10 to 50 Km/h.
Principle :
When the wind speed exceeds the threshold set by the EOLIS receiver RTS,
after 2 seconds, an UP order is given to the motor.
As long as the measured wind speed is higher than the adjusted threshold,
any order from the RTS control is inhibited.
When the wind speed falls below the threshold setting, a time delay of 30
seconds is activated.
After this time delay any order can be given with the RTS control.
“S” jumper :
When the jumper is cut, if a down control has been given just before the
wind appearance, the EOLIS receiver RTS will automatically send a down
control to the motor after 12 minutes.
The EOLIS receiver RTS is able to protect awnings against wind damage using EOLIS sensor
Cabling / fixing of the EOLIS sensor
1. Connect the cable
to the terminal.
2. Put the cover 3. Fix the sensor
to the wall.
4. Put and screw the
front box.
Mounting of the EOLIS sensor
WARNING : if the awning moves DOWN when pressing the UP button of the RTS control, invert the brown and black motor wires.
Wind threshold
adjustment
“S” jumper
Km/h
5010
EOLIS sensor
SC
▲ ▼ N N L
LT motor
common
NL
SC
L
= Main phase
N
= Main neutral
N
= Motor neutral
▲
= Motor up
▼
= Motor down
Earth
Neutral
Phase
SUPPLY
230V - 50 Hz
= WIND input
= COMMON input
SC
Eolis receiver RTS
Eolis sensor
Mains
OR
▲ ▼ N N L
SC
▲ ▼ N N L
SC
Loading...