Page 1
1
EEBC302A
PRO CHARGER 250
Battery Charger User Manual
IMPORTANT SAFETY INSTRUCTIONS
This manual contains important safety and operating
instructions for
Snap-on
PRO CHARGER 250 Battery Charger
model EEBC302A. Refer to the information in this manual often
for safe operation.
Read All Instructions
Read, understand and follow all safety messages and
instructions in this manual and on the test equipment. Safety
messages in this section of the manual contain a signal word, a
three-part message, and, in some instances, an icon.
The signal word indicates the level of hazard in a situation:
• Danger indicates an imminently hazardous situation which, if
not avoided, will result in death or serious injury to the
operator or bystanders.
• Warning indicates a potentially hazardous situation which, if
not avoided, could result in death or serious injury to the
operator or bystanders.
• Caution indicates a potentially hazardous situation which, if
not avoided, may result in moderate or minor injury to the
operator or bystanders.
The three-part message uses three different type styles to
further define the potential hazard.
• Normal type states the hazard.
• Bold type states how to avoid the hazard.
•
Italic type
states the possible consequences of not avoiding
the hazard.
An icon, when present, gives a graphical description of the
potential hazard.
SAVE THESE INSTRUCTIONS
Page 2
2
Safety Information
Battery Gases, Charging Preparation and Charger Location
Risk of explosion. Gases produced by a battery are
highly explosive.
• Wear safety goggles and protective clothing, user
and bystander.
• Use charger in an area having at least 4 air
changes per hour.
• Read, understand and follow all instructions for
charger, battery, vehicle and any equipment used
near battery and charger.
• Do not obstruct vents on charger housing.
• Do not smoke, strike a match, place metal tools on
battery or cause a spark in the vicinity of the
battery. When removing battery cables, remove
ground cable first.
• Clean terminals before charging battery. During
cleaning, keep airborne corrosion from eyes, nose
and mouth. Use baking soda and water to
neutralize acid and help eliminate airborne
corrosion.
• Never allow clamps on charger cables to touch
each other.
• Do not expose charger to rain, snow or wet
conditions.
• Do not allow battery gasses or acid to contact
charger cabinet. Do not place charger directly
above or below battery.
• Fill battery to level specified by battery
manufacturer using distilled water.
• Remove or do not remove cell caps while charging
per manufacturer's instructions.
• Make sure charger cable clamps make tight
connections.
Battery explosion can cause injury.
Acid Burns
Battery acid is highly corrosive sulfuric acid.
• Wear safety goggles, user and bystander.
• Wear protective gloves.
• Make sure someone can hear you or is close
enough to provide aid when working near battery.
• Have plenty of fresh water and soap nearby. If
battery acid contacts skin, clothing or eyes, flush
the exposed area with soap and water for 10
minutes. Seek medical help.
• Do not touch eyes while working near battery.
Battery acid can burn eyes and skin.
Page 3
3
Safety Information
Grounding, AC Power Cord Connections
and General Charger Use
Risk of electric shock and fire.
• Before connecting power cord to outlet make sure
controls are set to OFF.
• Do not remove or bypass the grounding pin.
• Do not operate charger with damaged cord or
plug. Replace cord or plug immediately.
• Position power cord and charger cables away from
the hood, doors or hot/moving engine parts where
they could be damaged.
• Use extension cord only when absolutely
necessary. An extension cord up to 25 feet must
be 18 AWG, up to 50 feet must be 14 AWG, up to
100 feet must be 12 AWG and up to 150 feet must
be 10 AWG and extension cord plug and charger
plug must have the same number, size and shape
of pins.
• Never alter AC cord or plug provided. If it will not
fit outlet, have proper outlet installed by a
qualified electrician.
• Unplug power cord using plug rather than cord
when disconnecting charger from outlet.
• Charger power cord uses equipment-grounding
conductor and a grounding plug. Plug only into a
three-prong 120 VAC outlet that is correctly
installed and grounded in accordance with all
ordinances and local codes.
• When using an adapter refer to
Figure 1
.
• Unplug power cord from outlet before cleaning or
maintaining charger. Turning off controls will not
reduce this risk.
• Do not operate charger after a sharp impact,
dropping or any other damage. Do not
disassemble charger. Call
Snap-on/Sun
Representative for repairs.
• Use only recommended attachments.
• Do not charge a frozen battery. Do not overcharge
a battery.
• Use charger only for lead-acid automotive
batteries and for automotive cranking assist using
procedure in this manual. Do not use charger for
charging dry-cell batteries.
Electric shock or fire can cause injury.
Page 4
4
Safety Information
Refer to
Figure 1.
Use the charger on a nominal 120 VAC
circuit that has a grounding outlet that looks like B. An adaptor
can be used, such as one like E to connect the plug to a twopole outlet like C, until a properly grounded outlet can be
installed by a qualified electrician.
Figure 1:
Outlet and Plug Configurations
A – Charger Power Cord Plug
B – Grounded Power Outlet
C – Ungrounded Power Outlet
D – Green Grounding Lug, must be properly
grounded
*
E – Grounding Adaptor
*If necessary, replace original outlet cover plate screw with a
longer screw that will secure adaptor ear or lug to outlet cover
plate, making ground connection to grounded outlet.
Risk of entanglement.
Keep yourself, clothing and battery charger leads
clear of moving parts such as fan blades, pulleys,
hood, and doors.
Moving parts can cause injury.
Thermal Burns
Risk of burns.
Batteries can produce a short-circuit current high
enough to weld jewelry to metal. Remove jewelry
such as rings, bracelets and watches before working
near batteries.
Short circuits can cause injury.
Page 5
5
Safety Information
Charging Instructions
Follow the information in this section to help ensure safety when
connecting the charger cables to battery. For additional
information refer to
Battery Charging Procedure
.
Battery in Vehicle
Use this information when charging battery in vehicle.
• Do not charge automotive batteries installed in boats.
Remove the battery and charge on shore. Onboard charging
requires equipment designed for marine use.
• Identify battery terminal polarity.
— Negative terminal may be marked NEG, N or –.
— Positive terminal may be marked POS, P or +.
✓✓
✓✓
The positive terminal is usually larger diameter than the
negative terminal on batteries with top terminals.
• Identify system ground.
— Negative ground system has negative terminal connected
to chassis. This is the most common type.
— Positive ground system has positive terminal connected
to chassis.
Negative Ground
• Connect positive charger cable clamp—red—to positive
battery terminal.
• Connect negative charger cable clamp—black—to vehicle
chassis, heavy gauge metal part of frame or engine block,
away from battery.
✓✓
✓✓
Do not connect the ground clamp to the carburetor, fuel
line or body sheet metal.
Positive Ground
• Connect negative charger cable clamp—black—to negative
battery terminal.
• Connect positive charger cable clamp—red—to vehicle
chassis, heavy gauge metal part of frame, or engine block
away from battery.
✓✓
✓✓
Do not connect the ground clamp to the carburetor, fuel
line or body sheet metal.
Page 6
6
Safety Information
Disconnecting Charger
• Turn Length of Charge Timer to OFF,
• Disconnect power cord,
• Remove clamp from ground, and
• Remove clamp from battery terminal.
Battery Not in Vehicle
Follow this procedure when charging battery out of vehicle.
• Identify battery terminal polarity.
— Negative terminal may be marked NEG, N or –.
— Positive terminal may be marked POS, P or +.
✓✓
✓✓
The positive terminal is usually larger diameter than the
negative terminal on battery with top terminals.
• Attach at least a 24-inch long 6 gauge (AWG) insulated
battery cable to negative terminal.
— When charging side terminal battery out of vehicle, use
side terminal adaptors.
• Connect positive charger cable clamp—red—to positive
battery terminal.
• Position yourself and free end of cable as far away from
battery as possible, then connect negative charger cable
clamp—black—to free end of cable previously installed. Do
not face battery when making final connection.
Disconnecting Charger
• Turn Length of Charge Timer to OFF,
• Disconnect power cord,
• Remove clamp from negative cable, and
• Remove clamp from positive terminal.
✓✓
✓✓
Always disconnect charger in reverse sequence of
connecting procedure. Stand as far away as possible
and face away from the battery when disconnecting
ground clamp from cable connection.
Page 7
EEBC302A
Operating Instructions
Use this section for information about using the EEBC302A
PRO CHARGER 250 Portable Battery Charger correctly and
safely. The following are included:
• Functional Description,
• Battery Charging,
• Maintenance,
• Cranking Assist,
• Assembly, and
• Parts List.
Functional Description
The EEBC302A PRO CHARGER 250 Portable Battery Charger
is a general-purpose 12-volt charger for automobile batteries
with timed or continuous charging capability and UL Cranking
Assist capability. This fan-cooled charger can easily be moved
to a battery requiring charge. Also, the charger can charge two
6-volt batteries simultaneously. Two amperage selections
accommodate several sizes of 12-volt batteries for automobiles.
The following information describes control panel features of the
charger.
Figure 2:
Control Panel
7
Page 8
8
Operating Instructions EEBC302A
A—Charging Mode Switch
Two-position rocker amperage charging rate mode switch
selects continuous charging of 35 amps in low position or 70
amps in high position and UL Cranking Assist output of 250
amps DC.
B—Length of Charge Timer
Selects charger power mode and charge duration with manual
or automatic shut-off functions.
• OFF electrically shuts off power to the charger.
— Select before connecting or disconnecting power cord or
any leads.
• HOLD powers charger until OFF is manually selected.
— Select when desired charge time exceeds 120 minutes.
Charger does not turn off automatically when this function
is selected.
• CHARGE TIME is number of minutes the charger operates
before automatically shut-off. Charger shuts off automatically
after number of minutes selected lapse when this function is
selected.
— Up to 120 minutes can be selected. Increase or
decrease charge time as needed by selecting new time.
✓✓
✓✓
The charger automatically shuts off when the charge
time reaches zero.
C—Ammeter
Displays amps, 0 to 100 DC, flowing from charger into battery.
AC Power Cord (Not shown)
Extends 9.5 feet from back of charger.
DC Leads (Not shown)
Extend 7 feet from back of charger.
Page 9
9
EEBC302A Operating Instructions
Battery Charging Procedure
1. Perform visual inspection of battery(ies) before charging
to help prevent personal injury and property damage.
Check the following conditions, correcting defects and/or
replacing battery(ies) and components as required.
— Cracked case.
— Improper electrolyte level - fill to level specified by
battery manufacturer.
— Frozen electrolyte or resulting damage.
— Loose or corroded terminal/cable connection.
— Frayed or broken cables.
— Loose or over-tightened battery hold-down.
— Correct size and capacity for vehicle.
2. Set Charging Mode Switch to correct amperage for
battery being charged. Determine battery voltage from
vehicle owner's manual or battery instructions. Use:
— Low (35 amps) for smaller batteries, cold or mildly
sulfated batteries, and
— High (70 amps) for quick charge.
3. Measure and record batter y state of charge.
— Specific gravity.
— Open circuit voltage.
✓✓
✓✓
State of charge is used in step 9 to determine charge
time.
4. Verify AC power cord is disconnected from outlet and
Length of Charge Timer is set to OFF.
5. Connect charger cables to battery and power cord to
outlet. For additional information refer to
Important
Safety Instructions–Charging Instructions
.
• Never alter AC cord or plug provided. If it will not
fit outlet, have proper outlet installed by a
qualified electrician.
• Read, understand and follow Safety Information in
front of this manual.
Page 10
10
Operating Instructions EEBC302A
6. Set Length of Charge Timer to HOLD.
7. Obser ve DC AMPS. Some reading should be evident.
— If OK, allow to stabilize for 5 minutes. Recheck DC
AMPS reading.
— If not, set Length of Charge Timer to OFF.
Determine reason for no reading. Correct before
proceeding.
8. Deter mine battery capacity. Capacity is usually marked
on battery and rated in:
— Ampere-Hours (AH),
— Reserve Capacity (RC), or
— Cold Cranking Amps (CCA).
✓✓
✓✓
Battery capacity is used in step 9 to determine charge
time.
9. Deter mine charge time using
Chart 1
.
✓✓
✓✓
A battery charged 25% or lower may easily freeze,
charge immediately.
Chart 1:
Determining Length of Charge Using State of Charge and Capacity
STATE-OF CHARGE
STATE-OF-CHARGE 100% 75% 50% 25% DEAD
6 & 12V Specific Gravity 1.260 1.225 1.185 1.140 1.110
12V Open Circuit Voltage 12.6 12.4 12.1 11.9 11.8
6 V Open Circuit Voltage 6.3 6.2 6.1 6.0 5.9
BATTERY CAPACITY
6V Battery Voltage 12V
SMALL MEDIUM LARGE Battery Capacity SMALL MEDIUM LARGE
100 155 200+ Ampere hours 40 60 80+
160 275 430+ Reserve Capacity 60 90 100+
500 700 900+ Cold Cranking Amps 300 400 500+
LENGTH OF CHARGE TABLE
BA
TTERY CAPACITY % CHARGE BEGINNING AMPS CHARGE RATE
Small 0-25 45 30 30 25 25 20
25-50 30 20 20 15 15 10
50-75 15 10 10 10 5 5
Medium 0-25 70 50 45 40 35 30
25-50 45 30 25 20 20 20
50-75 25 15 15 15 10 10
Large 10-25 90 55 55 50 45 45
25-50 60 40 34 30 30 30
50-75 30 20 20 15 15 15
APPROXIMATE MINUTES OF CHARGE 15 30 45 60 75 90
Page 11
11
EEBC302A Operating Instructions
Example:
A battery is determined to be medium capacity since its
CCA rating is 405 and Reserve Capacity is 90 minutes.
Open circuit voltage test shows 12.1 volts, indicating
about a 50% charge. Five minutes after the charger is
powered up, charging current is 20 amps. Therefore,
battery should be charged for 60 to 90 minutes, as
shown on the chart.
10. Set required charge time on Length of Charge Timer. If
charge time exceeds 120 minutes, perform one of
following.
— Set Length of Charge Timer for any portion of total
charge time. Reset timer for remaining time when
charge time ends.
— Reset Length of Charge Timer at any time to extend
amount of charge time until total time required is
reached.
— Set Length of Charge Timer to HOLD and manually
turn charger off when required time is reached.
Charger does not turn off automatically.
Overcharging can damage battery.
11. Periodically monitor state of charge to prevent
overcharging, especially near end of charge period.
Battery is completely charged when specific gravity
and/or charging voltage do not increase after two hours.
Charging More than One Battery
Passenger vehicles and light trucks with diesel engines may use
two batteries. Heavy-duty trucks, special service vehicles, some
agricultural and industrial equipment may use two or more
batteries.
Batteries may be charged in a group if:
• Wired in parallel with the positive terminal of one battery
connected to the positive terminal of the remaining
battery(ies) and the negative terminals connected to negative
terminals.
✓✓
✓✓
Charging time is twice as long for a group of batteries
wired in parallel as a single battery.
• Wired in series with the positive terminal connected to
negative terminal between batteries; and the voltage of all
batteries combined is 12 volts, i.e. two 6 volt batteries.
✓✓
✓✓
If one battery of a parallel or series group is charged and
another is discharged, isolate the battery(ies) and charge
separately.
Page 12
12
Operating Instructions EEBC302A
Cranking Assist
Use this procedure to help the battery crank the engine over in
a vehicle with a discharged battery.
• Use only on batteries in good condition.
• Do not use if the battery has been discharged for a long
period of time, since it may be sulfated.
1. Turn off all accessories and lights.
2. Connect clamps to batter y terminals. For additional
information refer to
Safety Information–Charging
Instructions
.
3. Plug charger power cord into properly grounded 120 VAC
outlet.
4. Set Length of Charge Timer to HOLD.
5. Charge batter y for five minutes.
✓✓
✓✓
Partially charging battery helps direct more power to
starter motor during cranking assist.
6. Crank engine.
✓✓
✓✓
Cranking assist is provided for approximately 3.5
seconds followed by a 125 second cool down.
Although most starter motors can withstand cranking
for 15 seconds, the charger only provides cranking
assist for 3.5 seconds before cool down is required.
Assembly Instructions
Use the following instructions to properly assemble battery
charger before use.
Figure 3:
Assembly Diagram—Power Cord and Cables Not Shown
Page 13
13
EEBC302A Operating Instructions
1. Attach handle to charger with four screws provided.
2. Attach crossbar to handle with two screws provided.
3. Attach foot to base with two hex head screws provided.
4. Slide wheel onto axle with hub toward charger, then slide
axle through charger base.
5. Place remaining wheel on axle and tap retainer nuts onto
axle.
Maintenance
• Unplug power cord from outlet before cleaning or
maintaining charger. Turning off controls will not
reduce this risk.
• Read, understand and follow Safety Information in
the front of this manual.
Clean the case using a mild detergent. Do not allow liquid to
drip into the case.
Do not remove the case to perform routine maintenance. Worn
parts can compromise safety and charger performance.
Replace parts as needed. For service, contact your sales
representative.
Parts List
Description Part Number
Rectifier Assembly ...................................... BC4200-2000R
Transformer Assembly ................................ EAT0003K11AR
Fan Blade ................................................................ 2-1268
Fan Motor ............................................................ 2-10166-1
DC Leads with Clamps .................................. BC4200-100R
DC Circuit Breaker .................................................. 2-15366
AC Circuit Breaker .................................................. 2-10266
Ammeter .................................................................... 4-280
Power Cord .............................................................. 6-2821
Range Switch ............................................................ 2-9958
Charge Timer .......................................................... 2-14866
Knob, Charge Timer .................................................. 8-8230
Foot with 4 Screws ...................................... EAK0073K27A
Wheel Kit ...................................................... EAK0073K26A
Includes 2 wheels, 2 push nuts and axle
Page 14
14
Operating Instructions EEBC302A
Wiring Diagram
Figure 4:
Wiring Diagram, EEBC302A PRO CHARGER 250
B – Black
C – White
E – Red
F – Green
G – Blue
SAVE THESE INSTRUCTIONS
Page 15
15
EEBC302A Operating Instructions
Snap-on
PRO CHARGER 250 Battery Charger Limited Warranty
Limited Warranty. Snap-on Tools Company warrants only to the original Buyer that under normal use,
care and service, the Battery Charger shall be free from defects in material and workmanship f or (1) year
from the date of original invoice (except as otherwise provided herein). The transformer and rectifier
warranty period is (5) years from the date of original invoice.
This Warranty does not cover (and separate charges for parts, labor and related expenses shall apply
to) any damage to,malfunctioning, inoperability or improper operation of the Battery Charger caused by,
resulting from or attributable to (A) abuse, misuse or tampering; (B) alteration, modification or
adjustment of the Battery Charger by other than authorized representatives of Snap-on; (C) repair or
maintenance (other than specified operator maintenance) of the Battery Charger or related equipment,
attachments, peripherals or optional features by other than authorized representatives of Snap-on; (D)
improper or negligent use, application, operation, care, cleaning, storage or handling; (E) fire, water,
wind, lightning or other natural causes; or (F) adverse environmental conditions, including, without
limitation, excessive heat, moisture, corrosive elements, or dust or other air contaminants; radio
frequency interference;electric power failure; power line volta ges bey ond those specified for the Battery
Charger; unusual physical, electrical or electro-magnetic stress; and/or any other condition outside of
environmental specifications of Snap-on.
NO OTHER WARRANTIES, EXPRESS, IMPLIED OR STATUTORY, INCLUDING WITHOUT LIMITATION
ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE,SHALL
APPLY, AND ALL SUCH WARRANTIES ARE HEREBY EXPRESSLY EXCLUDED.
The obligations of Snap-on under this warranty are limited solely to the repair or, at the option of
Snap-on, replacement of or refund of the original purchase price for, Battery Charger or parts which to
the satisfaction of Snap-on are determined to be defective and which are necessary, in the judgment of
Snap-on, to return the Battery Charger to good operating condition. Repairs or replacements qualifying
under this Warranty will be performed or made on regular business days during normal working hours
of Snap-on within a reasonable time following Buyer's request. All requests for warranty service must
be made during the stated warranty period.
Limitation of Liability . In no event shall Snap-on be liable to Buyer or any one claiming thr ough or against
Buyer for any special, indirect or consequential damages (including, without limitation, lost profits,
revenues, anticipated sales, business opportunities or goodwill; interruption of business; or loss of
business information) resulting from or arising out of (a) negligence;(b) any breach or non-performance
of this agreement or any duties, obligations, responsibilities, representations or warranties hereunder;
(c) the delivery, installation, operation, performance, use or maintenance (or non-performance, delay in
or failure) of the Battery Charger, or services to be provided hereunder; or (d) otherwise, even if Snapon has been advised of the possibility of such damages.
The entire liability of Snap-on for damages to Buyer resulting from or arising out of the
performance or non-performance of this Agreement or for any cause whatsoever, and regardless
of the form of action, whether in contract or in tort (including negligence or strict liability) or any
other legal theory, shall not exceed the purchase price for the specific item(s) of Battery Charger
found to be defective. Buyer assumes full responsibility for the overall operating environment in
which the Battery Charger is to function, including, without limitation, temperature, humidity,
corrosive elements, and dust or other air contaminants.
For further information contact:
Your Snap-on Dealer or Representative
Snap-on T ools Company
2801- 80th Street
Kenosha, WI 53141-1410
1-800-786-6600
Copyright1998 Snap-on Tools Company
Page 16
Operating Instructions EEBC302A
©1999 Snap-on Incorporated
ZEEBC302A Printed in U.S.A. – (6/99)
Loading...