Suitable for Installation within a ceiling void
Installation & User Guide
User Information:
This appliance can be used by children aged from 8 years and above and
persons with reduced physical, sensory or mental capabilities or lack of
experience and knowledge if they have been given supervision or
instruction concerning use of the appliance in a safe way and understand
the hazards involved. Children shall not play with the appliance. Cleaning
and user maintenance shall not be made by children without supervision
A means for disconnection from the supply mains having a contact
separation in all poles that provides full disconnection under overvoltage
category III conditions must be incorporated in the fixed wiring in
accordance with the wiring rules.
Ensure that the fan convector is switched-off before opening the cover.
CASPIAN SKYLINE®
CT60 AC
Ceiling Level Fan Convector
CABLE ENTRY
PIPE ENTRY
HINGED GRILLE
VALVE ACCESS PANEL
FILTER RETAINER
Introduction
This heater is designed to be installed into suspended T-bar and plasterboard ceilings (The
minimum height of the void into which the unit will be installed should be a minimum of 250mm).
User Information:
This heater must not be installed in wet rooms or other high humidity areas.
This heater is designed for use on standard two-pipe pumped central heating systems with a
maximum water temperature of 86° C and a maximum pressure of 6 bar (88lbs/in²).
Pipe connections are 22mm and either pipe may be used as flow or return.
This heater is classified as a fixed appliance and the electrical connection should be via a 3A fused
spur. The fused spur must not be directly below the heater but should be accessible after
completion of the installation. This heater must be earthed.
It is recommended that this heater is wired via a remote room thermostat.
To avoid the possibility of vibration this heater must be fitted to a flat even surface.
This heater is fitted with a 35°C Low Limit Stat (L.T.C).
To conform to Building Regulations Part L (Part J in Scotland), a remote room thermostat can be
used in conjunction with this heater. Refer to the instructions supplied with the thermostat.
Please note the guarantee may be invalidated if this product is not installed and used in
accordance with these instructions.
For further details please contact our Technical Support on 01245 324560.
Figure 1
2
Fault Finding
1) The fan does not run on any switch setting.
a) Check the power supply is switched ON.
b) Check the fuse in the fused spur.
c) Check the wiring at the fused spur.
2) No heat output.
a) Vent any trapped air from the system (with the heating system turned OFF).
b) Check the central heating is switched ON.
c) If a thermostat is fitted ensure it is calling for heat.
d) Balance the central heating system if installed on the same circuit as panel radiators and
e) Increase the boiler water temperature.
In the event of difficulty please contact our technical help-line on 01245 324560. It will be helpful if
you do not disconnect the heater from the central heating system.
A product brochure containing full technical specifications and list prices is available to
download from our website or in hard copy from our office. Also available on our website are
price lists, individual product datasheets, installation & user guides, where to buy, who to
Alternatively contact our office 9.00am to 5.00pm Monday to Thursday, 9.00am to 4.00pm to
Optional Accessories
Optional accessories are available to offer additional control or functionally not offered by the heater
in its standard configuration.
Electrical Accessories
Wall Switch Kit CT60AC WSC
Allows an on/off wall switch to be mounted on the wall to control heater.
Suitable cable to connect the switch from the heater to the switch is not supplied.
Adjustable low temperature cut-out CT60 ALTC T3
This enables the end user to precisely select the temperature at which the fans will switch on when
combined with different heat sources.
Miscellaneous Accessories
Caspian 22mm Flexible Hoses CAS22FH
Replacement air filters
For accessories or spares please contact either your supplier or Smith’s Environmental
Products Ltd.
HEATER UNIT
GRILLE
T-BAR
HANGING
BOLT
HANGING
BOLT
TILE
T-BAR
TILE
Preparation
The following items should be included in the carton:
Caspian Skyline® CT60 AC unit.
Grille.
X4 M5 Screws.
Other items (Not included) required for a successful installation:
Three core mains cable.
Isolating valves (Failure to fit isolating valves may mean that the product is not serviceable
in the event of failure).
Air Vent/ Bleed valve.
Suitable mounting hardware (Such as chains, threaded rod etc).
Accessories including replacement air filters are available (See page 7).
In the event of any items missing or visible damage, please contact us on 01245 324560,
before continuing with the installation.
Installation
This heater should be mounted at a minimum height of 1.8m (To the underside of the grille) and a
maximum height 4m
Installation into a suspended T Bar ceiling
Figure 3
1) Choose the position in the ceiling grid that the heater is to be installed and remove the
chosen ceiling tile, as well as any surrounding tiles to provide adequate access during
installation.
2) Ensure suitable means of support such as threaded rods or chains are used and fixed into
place directly above the chosen grid position.
3) Lift the heater through the T bar grid into the void and securely attach the supports to the
heater.
4) Level the adjustable brackets (See figures 3 and 4.) with the finished ceiling and tighten
5) Lift the grille to the heater so that the holes in the grille align with the fixing holes in the
adjustable brackets
6) Fix the grille to the heater using the supplied screws
7) Proceed to page 5 for plumbing and electrical connection.
3
Loading...