Sloan WES-111 Installation Manual
Code No. 0816555
INSTALLATION INSTRUCTIONS FOR DUAL-FLUSH FLUSHOMETERS
Rev. 2 (08/12)
WES-111
Exposed Closet
Flushometer
for 1-1/2 Top Spud
EXPOSED TOP SPUD
1½” WATER CLOSET
• MODEL 111
• MODEL 113
• MODEL 115
• MODEL 116
EXPOSED REAR SPUD
1½” WATER CLOSET
• MODEL 120
Unless otherwise noted, Sloan Valve Company warrants this product, manufactured and sold
for commercial or industrial uses, to be free from defects in material and workmanship for
a period of three (3) years (one (1) year for special finishes, SF faucets, PWT electronics
and 30 days for PWT software) from date of first purchase. During this period, Sloan Valve
Company will, at its option, repair, replace, or refund the purchase price of any product which
fails to conform with this warranty under normal use and service. This shall be the sole and
exclusive remedy under this warranty. Products must be returned to Sloan Valve Company,
at customer’s cost. No claims will be allowed for labor, transportation or other costs. This
warranty extends only to persons or organizations who purchase Sloan Valve Company’s
products directly from Sloan Valve Company for purpose of resale. This warranty does not
cover the life of the batteries.
THERE ARE NO WARRANTIES WHICH EXTEND BEYOND THE DESCRIPTION ON
THE FACE HEREOF. IN NO EVENT IS SLOAN VALVE COMPANY RESPONSIBLE
FOR ANY CONSEQUENTIAL DAMAGES OF ANY MEASURE WHATSOEVER.
PRIOR TO INSTALLATION
Before you install the flushometer, be sure the items listed below are installed.
Also, refer to the rough-in diagram below.
• Closet fixture
• Drain line
• Water supply line
IMPORTANT:
• ALLPLUMBINGSHOULDBEINSTALLEDINACCORDANCE
WITH APPLICABLE CODES AND REGULATIONS.
• WATERSUPPLYLINESMUSTBESIZEDTOPROVIDEAN
ADEQUATE VOLUME OF WATER FOR EACH FIXTURE.
• FLUSHALLWATERLINESPRIORTOMAKING
CONNECTIONS.
Sloan’s flushometers are designed to operate with 10 to 100 psi (69 to 689
kPa) of water pressure.
TO THE VALVE IS DETERMINED BY THE TYPE OF FIXTURE
SELECTED.
requirements. Most Low Consumption water closets (1.6 gpf/6.0 Lpf) require a
minimum flowing pressure of 25 psi (172 kPa).
TOOLS REQUIRED FOR INSTALLATION
• Straight blade screwdriver
• Sloan A-50 Super-Wrench™, Sloan A-109 Plier Wrench or smooth jawed spud wrench
ROUGH-IN
MODEL 120MODELS 111, 113, 114, 115, 116
LIMITED WARRANTY
THE MINIMUM PRESSURE REQUIRED
Consult fixture manufacturer for minimum pressure
‡ Model 111 – 11½” (292 mm)
Model 113 – 16” (406 mm)
Model 114 – 34⅜” (873 mm)
Model 115 – 24” (610 mm)
Model 116 – 27” (686 mm)
!!! IMPORTANT !!!
When mounted on an ADA accessible bowl, the rough-in to the supply
inlet should be no higher than 37½” or the handle will exceed maximum
New ADAAG Guidelines allow for Split or Offset Grab Bars, check with
height allowances under ADA guidelines.
local authorities or reference section 604.5.2 of ADAAG.
!!! IMPORTANT !!!
Protect the chrome or special finish of Sloan Flushometers — DO
NOT USE toothed tools to install or service these valves. Use a
Sloan A-50 Super-Wrench™, Sloan A-109 Plier Wrench or smooth
jawed spud wrench to secure all couplings. Also see “Care and
Cleaning” section of this manual.
!!! IMPORTANT !!!
This product contains mechanical and/or electrical components
that are subject to normal wear. These components should be
checked on a regular basis and replaced as needed to maintain
the valve’s performance.
1 - INSTALL OPTIONAL SWEAT SOLDER ADAPTER (ONLY IF YOUR SUPPLY PIPE DOES NOT
HAVE MALE THREAD)
FINISHED WALL
Measure from finished wall to
A
C/L of fixture spud. Cut pipe
1⁄” (32 mm) shorter than this
measurement. Chamfer O.D.
and I.D. of water supply pipe.
Slide threaded adapter fully
B
onto pipe.
Sweat solder the adapter to pipe.
C
Measure from finished wall
A
to first thread of adapter
or threaded supply pipe
(dimension “X”). Cut cover
tube to this length.
Slide cover tube over pipe.
B
Slide wall flange over cover
tube until against wall.
WATER SUPPLY PIPE
WATER
SUPPLY PIPE
SWEAT
SOLDER ADAPTER
COVER TUBE
WALL
FLANGE
SET SCREW
1-1/4”
(32 mm)
SWEAT
SOLDER
ADAPTER
C/L OF
FIXTURE
SPUD
!!! IMPORTANT !!!
WITH THE EXCEPTION OF THE CONTROL STOP INLET, DO
NOT USE PIPE SEALANT OR PLUMBING GREASE ON ANY
Thread Control Stop onto pipe. Tighten
C
with a wrench.
SET SCREW
SUPPLY
FLANGE
Tighten Set Screw with a 1/16”
D
VALVE COMPONENT OR COUPLING!
IRON PIPE NIPPLE OR
COPPER PIPE WITH SWEAT
SOLDER ADAPTER
COVER TUBE
BAK-CHEK
CONTROL STOP
hex wrench. DO NOT install Vandal
Resistant Stop Cap at this time.
3-INSTALLVACUUMBREAKERCONNECTION
®
Slide spud coupling, nylon slip gasket, rubber gasket and spud flange
A
over vacuum breaker tube.
Insert tube into fixture spud.
B
Hand tighten spud coupling onto fixture spud.
C
NOTE
Follow instructions on bag of high back pressure vacuum
breaker kit included with flushometer: insert baffle into
groove of vacuum breaker sack; insert sack in vacuum
breaker tube; and place friction ring on top of sack.
4 - INSTALL FLUSHOMETER
Lubricate tailpiece o-ring with water. Insert adjustable tailpiece into
A
control stop. Tighten tailpiece coupling by hand.
Align flushometer directly above the vacuum breaker flush connection
B
by sliding the flushometer body IN or OUT as needed. Tighten vacuum
breaker coupling by hand.
Align flushometer body and securely tighten first the tailpiece coupling
C
(1), then the vacuum breaker coupling (2), and finally the spud
coupling
shown.
MAXIMUM adjustment of Sloan adjustable tailpiece is
½” (13 mm) IN or OUT from the standard 4¾” (121 mm)
(centerline of flushometer to centerline of control stop).
If roughing-in measurement exceeds 5¼” (133 mm), a
(3). Use a wrench to tighten these couplings in the order
NOTE
longer tail may be supplied.
FLUSHOMETER
BODY
VACUUM
BREAKER
COUPLING
2
VACUUM
BREAKER
FLUSH
CONNECTION
VACUUM
BREAKER TUBE
SPUD
COUPLING
NYLON SLIP
GASKET
RUBBER GASKET
SPUD FLANGE
TAILPIECE
COUPLING
1
O-RING
ADJUSTABLE TAILPIECE
C/L
FIXTURE
G-44
FRICTION
RING
SPUD
COUPLING
3
4-3/4”
(121 mm)
±1/2”
(13 mm)
CONTROL
STOP
C/L
SUPPLY
Loading...