Sloan EBF-187 Installation Manual
Code No. 0816302
Rev. 3b (11/08)
INSTALLATION INSTRUCTIONS FOR
SENSOR ACTIVATED LAVATORY FAUCETS
LIMITED WARRANTY
Sloan Valve Company warrants its EBF-85 and EBF-187 Faucets to be made of first class materials, free from defects of material or workmanship under normal use and to perform the
service for which they are intended in a thoroughly reliable and efficient manner when properly installed and serviced, for a period of three years (1 year for special finishes) from date of
purchase. During this period, Sloan Valve Company will, at its option, repair or replace any part or parts which prove to be thus defective if returned to Sloan Valve Company, at customer's
cost, and this shall be the sole remedy available under this warranty. No claims will be allowed for labor, transportation or other incidental costs. This warranty extends only to persons or
organizations who purchase Sloan Valve Company's products directly from Sloan Valve Company for purpose of resale. This warranty does not cover the life of the batteries (battery operated
models).
THERE ARE NO WARRANTIES WHICH EXTEND BEYOND THE DESCRIPTION ON THE FACE HEREOF. IN NO EVENT IS SLOAN VALVE COMPANY RESPONSIBLE FOR ANY CONSEQUENTIAL DAMAGES
OF ANY MEASURE WHATSOEVER.
PRIOR TO INSTALLATION
Prior to installing the Sloan EBF-85 or EBF-187 Faucet, install the items
listed below. Also, refer to the Rough-In illustrations on Page 2.
• Lavatory/sink
• Drain line
• Hot and cold water supply lines or tempered water supply line
Mixing Valve
When installing the faucet with a Sloan mixing valve, these Installation
Instructions AND the Installation Instructions packaged with the mixing
valve MUST be followed.
Important:
• INSTALL ALL PLUMBING IN ACCORDANCE WITH APPLICABLE CODES
AND REGULATIONS.
• KEEP THREAD SEALANT OUT OF YOUR WATERWAY TO PREVENT
COMPONENT PART DAMAGE! DO NOT USE ANY SEALANT ON
COMPRESSION FITTINGS. FOR THREADED PIPE FITTINGS, DO NOT
APPLY SEALANT TO THE FIRST TWO “STARTER” THREADS.
• FLUSH ALL WATER LINES UNTIL WATER IS CLEAR BEFORE CONNECTING
SOLENOID TO SUPPLY STOPS.
DO NOT INSTALL THE BATTERIES UNTIL THE FAUCET IS COMPLETELY
INSTALLED. If the batteries are installed before the fiber optic cable has
been connected to the valve module, the faucet will not properly set the
sensing range for the sink on which it is installed.
DO NOT INSTALL THE SPRAY HEAD UNTIL AFTER THE SUPPLY LINES
HAVE BEEN FLUSHED.
BAK-CHEK®TEE USAGE
When connecting the Sloan EBF-85 or EBF-187 Faucet to both hot and cold
water supplies, a Bak-Chek
®
Tee is provided and required as illustrated in
the Rough-in illustrations on Page 2. Water temperature can be controlled
by adjusting the supply stops.
When connecting the faucet to a single line water supply or a pre-tempered
water supply, a Bak-Chek
®
Tee is not required.
A Bak-Chek
®
Tee is not required or provided when a Temperature Mixing
Valve is included with the faucet.
TOOLS REQUIRED FOR INSTALLATION
• Open end wrenches for hex sizes: 1/2”, 9/16”, 5/8”, 15/16”
• Basin wrench
• Phillips head screwdriver, #2
• Hammer (if installing plastic or hollow wall anchors to mount valve
module)
• 0.05” hex wrench (supplied)
• Spray head key (supplied)
• 1/4” drill bit (if plastic wall anchors are used to mount valve module)
• 5/16” drill bit (if hollow wall anchors are used to mount valve module)
• 3/8” drill bit (if toggle nut anchors are used to mount valve module)
Model EBF-85
Battery Powered, Sensor Activated Lavatory Faucet
Furnished with a Black Plastic Throat Plate
Model EBF-187
Battery Powered, Sensor Activated Lavatory Faucet
Furnished with a Chrome Plated Metal Throat Plate
Compliant to: ASME A112.18.1
and CSA B125.1
2
1A
ETF-295-A (for EBF-85) Single Hole 4” Trim Plate
A
Slide Rubber Faucet Gasket onto Faucet Shank. Ensure that Roll
Pin on base of Faucet fits into hole in Rubber Faucet Gasket.
FAUCET ROUGH-IN
Note: When installing with a Sloan Mixing Valve, install Faucet and Trim
Plate before installing Mixing Valve. For complete installation guidelines,
refer to the Installation Instructions supplied with the Sloan mixing valve.
B
Insert Hex Bolts into Black Plastic Base Plate (if sink has only a
center hole, see note above). Place Chrome Cover Plate over
Black Plastic Base Plate. Slide Trim Plate assembly onto Faucet
Shank. Align Roll Pin with small hole in Trim Plate assembly.
Note: If Trim Plate is used on a sink with a center hole only, Trim Plate
Bolts are not used. Apply plumber’s putty to underside of Trim Plate to
prevent Faucet from rotating.
C
Insert Trim Plate Bolts through the 4 inch (102 mm) spread deck
holes and Faucet Shank through the 1 inch (25 mm) minimum
diameter deck hole. Secure Trim Plate to Deck using the large
Plate Washers and Hex Nuts supplied. Secure Faucet from below
Deck using the Flange Nut supplied.
ROLL PIN
RUBBER
FAUCET GASKET
COVER PLATE
BLACK PLASTIC
BASE PLATE
DECK
FAUCET SHANK
TRIM PLATE
HEX BOLTS (2)
PLATE
WASHERS (2)
HEX NUTS (2)
FLANGE NUT
1
Install Faucet Spout and Trim
Plate — Refer to the appropriate
step (1A-1C) for your application.
EBF-85 and EBF-187 Faucet with Bak-Chek®Tee
for Hot and Cold Water Supply
(shown with 4” trim plate)
EBF-85 and EBF-187 Faucet with ADM Variation
Mixing Valve for Hot and Cold Water Supply
(shown with 8” trim plate)
EBF-85 and EBF-187 Faucet with BDM and BDT
Variation Mixing Valves for Hot and Cold Water
Supply (shown with 4” trim plate)
EBF-85 and EBF-187 Battery Powered Faucet
EBF-85 FAUCET
FAUCET INSTALLATION
3
1B
ETF-312-A (for EBF-187) Single
Hole 4” Trim Plate
A
Slide Rubber Faucet Gasket onto Faucet Shank. Ensure that Roll
Pin on base of Faucet fits into hole in Rubber Faucet Gasket.
B
Slide Trim Plate and Back-up Spacer onto Faucet Shank. Align Roll
Pin with small slot in Trim Plate.
C
Secure Faucet from below Deck using the Flange Nut supplied.
ROLL PIN
RUBBER FAUCET
GASKET
TRIM PLATE
BACK-UP
SPACER
DECK
FAUCET SHANK
FLANGE NUT
1C
ETF-510-A (for EBF-85/187) Single
Hole 8” Trim Plate
A
Slide Rubber Faucet Gasket onto Faucet Shank. Ensure that Roll
Pin on base of Faucet fits into hole in Rubber Faucet Gasket.
B
Slide Trim Plate and Back-up Spacer onto Faucet Shank. Align Roll
Pin with small slot in Trim Plate.
C
Slide Washer Gaskets over Studs. Place Studs and Faucet Shank
through Base Gasket and holes in Deck.
D
Secure Trim Plate from below Deck using the two (2) Fender
Washers and two (2) Finger Nuts supplied.
E
Secure Faucet from below Deck using the Flange Nut supplied.
ROLL PIN
RUBBER
FAUCET
GASKET
TRIM PLATE
STUD
DECK
FAUCET SHANK
WASHER
GASKET (2)
BASE
GASKET
BACK-UP
SPACER
FENDER
WASHER (2)
FINGER NUT (2)
FLANGE NUT
EBF-187 FAUCET
2
Install Valve Module Wall Bracket
A
Install the Wall Bracket in an appropriate location as shown in the
Rough-In illustrations on Page 2.
WALL
BRACKET
BASE
WALL
BRACKET
SELF-TAPPING SCREW
PLASTIC ANCHOR
WITH SCREW AND
WASHER SHOWN
B
Position Wall Bracket within 20 inches (508 mm) from Faucet.
When installed, the Fiber Optic Cable from the Faucet Spout to the
Valve Module should have some slack.
C
Use Wall Bracket Base as a template to mark off holes on wall for
Mounting Screws. Determine the appropriate Mounting Fastener
for the particular wall type (three different fastener types are
included; see parts list). Drill two (2) appropriately sized holes:
For Plastic Wall Anchor — 1/4” (6 mm) holes
For Hollow Wall Anchor — 5/16” (8 mm) holes
For Toggle Nut Anchor — 3/8” (10 mm) holes
3
Connect Flex Hose or Copper
Tubing to Spout
A
Install the 1/4 inch end of the 1/4 to 3/8 inch Compression Fitting
onto the Spout’s copper Supply Tube.
IMPORTANT: Keep thread sealant out of your waterway to prevent
component part damage! DO NOT use any sealant on compression
fittings. For threaded pipe fittings, DO NOT apply sealant to the first
two "starter" threads.
B
Connect one end of Flex Hose or Copper Tube to the Compression
Fitting.
COPPER
SUPPLY TUBE
1/4 TO 3/8 INCH
COMPRESSION
FITTING
FLEX HOSE
3/8” (10 mm)
COPPER
SUPPLY TUBE
FLEX HOSE
CONNECTION
COPPER TUBE
CONNECTION
FERRULE
COMPRESSION
NUT
D
Install Wall Bracket Base to wall using the appropriate fastener.
Loading...