Slant/Fin LX-85A User Manual
Residential • Gas fired • Hot Water Boilers
User’s Information Manual
Lynx Direct-Vent Sealed Combustion Condensing Boiler
Model LX-85A
FOR YOUR SAFETY:
• Before operating this boiler, READ this manual.
• DO NOT attempt to install, service or repair this boiler yourself. There are no user serviceable
parts. Contact a qualified service agency if your boiler needs repair or maintenance. Ask your gas supplier for a
list of qualified service agencies.
• A qualified service agency should inspect the venting system of this boiler on an annual basis.
WARNING: If the information in this manual is not
followed exactly, a fire or explosion may result
causing property damage, personal injury or loss
of life.
__ DO NOT store or use gasoline or other
flammable vapors and liquids in the
vicinity of this or any other appliance.
__ WHAT TO DO IF YOU SMELL GAS
• DO NOT
• DO NOT touch any electrical switch
• DO NOT use any phone in your
building.
• Immediately call your gas supplier
from a neighbor’s phone. Follow the
gas supplier’s instructions.
• If you cannot reach your gas supplier,
call the fire department.
try to light any appliance.
__ Installation and service must be performed by
a qualified installer, service agency or the gas
supplier.
Your gas boiler must be installed and serviced by a qualified service agency or gas
supplier
The lac
.
k of proper ser
vice can result in a dangerous condition.
This manual must be left with owner, hung on or
Owner should retain man
adjacent to the boiler
for future reference.
.
Printed in U.S.A. 1008 Part No. 84-5757000 Publication No. LXA-UIM
ual
Lynx Model LX-85A
2
Figure 1. Location and identification of parts.
WELCOME TO OUR VALUED CUSTOMER
You are now the owner of a Slant/Fin Lynx gas-fired boiler,
another quality heating product designed and manufactured
by an industry leader, to provide your family with many years
of reliable comfort and trouble-free performance.
The care and maintenance of your new boiler is important to
prevent a hazardous condition which might result form lack
of proper servicing. Therefore, you should perform regular
“owner” inspections as described in this manual (and report
y concerns to a qualified service technician) as well as
an
our boiler serviced by a qualified service technician at
e y
hav
least once a y
heating season.
ear, preferably before the beginning of each
LIGHTING INSTRUCTIONS
Locate
instructions label attached to the boiler. For reference, we
have reproduced those instructions in this manual.
, read and then follow the procedures on the lighting
DO NOT use this boiler if any part has been
underwater. Immediately call a qualified service
technician to inspect the boiler and to replace
any part of the control system and any gas
control which has been underwater.
WARNING
Should overheating occur or the gas supply
fail to shut off, DO NOT turn off or disconnect
the electric supply to the circulator pump.
Instead,
shut off the gas suppl
EXTERNAL to the appliance.
y at a location
WARNING
SLANT/FIN DOES NOT PERMIT THE USE OF
VENT DAMPERS ON LYNX BOILER. OTHER
AMPERS OR DEVICES
D
POSE ARE NOT
PERMITTED
WITH SIMILAR PUR
.
-
Keep the boiler area clean and free of all materials that can burn.
NEVER close or reduce openings that supply air for the boiler fire and for ventilation.
3
Lynx Model LX-85A
NSPECTION
I
Your boiler and heating system will last an indefinitely long
time at full efficiency, if it is inspected regularly and is kept
in good repair and adjustment. You, the user, should make
egular inspections, and report any problems to your
r
ervice agency. At regular intervals, you should have that
s
gency inspect the system and make repair adjustments as
a
necessary. What you and the service agency should do is
listed below. Contact your gas supplier for a list of qualified
service and repair agencies.
USER INSPECTION
The user should make the following inspections at least
once each month during the heating season and once just
before cold weather starts. Lynx LX-85A boiler may be
installed and vented either as direct-vent boiler, which all
air for combustion is obtained directly from outside
through the air intake piping or as non-directvent boiler, which all air for combustion is taken from
inside the boiler room. Typical direct-vent installations are
shown on Figures 2 and 3. Non-direct-vent installation is
shown on Figures 4, 5 and 6.
. VENTING AND AIR INTAKE SYSTEM REGULAR
1
NSPECTION
I
Inspect the system regularly for condensation, corrosion,
sagging and/or physical damage. A qualified professional
hould service the boiler annually and include such an
s
nspection at that time. The homeowner should look over the
i
ystem monthly for damage, water stains, any signs of rust,
s
other corrosions or separation of the vent and air intake
piping (if direct-vent).
Should an inspection turn up signs of condensation,
corrosion, sagging or damage, the boiler should be shut
down immediately and the condition should be corrected by
a qualified professional.
If the boiler is vented horizontally through the wall, the
outside termination, louvers and screen should be checked
for any debris blocking the opening and cleaned as
required.
Figure 2. Direct vent, sidewall venting illustration.
Figure 3.
Direct vent,
through a roof.
venting and air intake
Lynx Model LX-85A
4
Figure 4. Non-direct vent, sidewall venting.
Loading...