Page 1
TM
STVG569BTBK / STVG569BTW
INSTRUCTION MANUAL
www.singingmachine.com
The Singing Machine® is a registered trademark of The Singing Machine Co., Inc.
Page 2
Warnings
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT
REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS
INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
The Caution marking is located on the bottom panel.
DANGEROUS VOLTAGE: The lightning flash with arrowhead
symbol within an equilateral triangle is intended to alert the
user to the presence of uninsulated dangerous voltage within
the product’s enclosure that may be of sufficient magnitude to
constitute a risk of electric shock to persons.
ATTENTION: The exclamation point within an equilateral
triangle is intended to alert the user to the presence of
important operating and maintenance (servicing) instructions
in the literature accompanying this product.
DRIPPING WARNING: This product shall not be exposed to dripping or
splashing, and no objects filled with liquids, such as vases, shall be placed
on the product.
VENTILATION WARNING: The normal ventilation of the product shall not be
impeded for intended use.
SAFETY VERIFICATION: This device is made and tested to meet safety
standards of the FCC, requirements and compliance with safety
performance of the U.S. Department of Health and Human Services and
also with FDA Radiation Performance Standards 21 CFR Subchapter.
Warnings:
• This CD player employs a laser light beam. Only a qualified service person
should remove the cover or attempt to service this device, due to
possible eye injury.
• The use of controls, adjustments, or procedures other than those
specified herein might result in hazardous radiation exposure.
• The apparatus shall be used in an open area.
CAUTION!
Invisible laser radiation when open and interlocks defeated. Avoid exposure
to beam.
WARNING: TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE
THIS UNIT TO RAIN OR MOISTURE.
FCC WARNING: This equipment may generate or use radio frequency
energy. Changes or modifications to this equipment may cause harmful
interference unless the modifications are expressly approved in the
instruction manual. The user could lose the authority to operate this
equipment if an unauthorized change or modification is made.
This device complies with part 15 of the FCC Rules. Operation is subject
to the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
NOTE: This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses
and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will
not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
• The rating information is located at the bottom of the unit.
INDUSTRY CANADA NOTICE:
This device complies with Industry Canada Iicense-exempt RSS standard(s).
Operation is subject to the following two conditions:
1. This device may not cause interference, and
2. This device must accept any interference, including interference that
may cause undesired operation of the device.
CAN ICES-3(B)/NMB-3(B)
Class II equipment symbol.
This symbol indicates that the unit has a double insulation
system.
Important Safety Information
1. Read these Instructions.
2. Keep these Instructions.
3. Heed all Warnings.
4. Follow all Instructions.
5. Do not use this apparatus near water.
6. Clean only with a dry cloth.
7. Do not block any of the ventilation openings. Install in
accordance with the Manufacturer’s instructions.
8. Do not install near any heat sources such as radiators, heat
registers, stoves, or other apparatus (including amplifiers) that
produce heat.
9. Do not defeat the safety purpose of the polarized or groundingtype plug. A polarized plug has two blades with one wider than
the other. A grounding type plug has two blades and a third
grounding prong. The wide blade or the third prong are provided
for your safety. When the provided plug does not fit into your
outlet, consult an electrician for replacement of the obsolete
outlet.
10. Protect the power cord from being walked on or pinched
particularly at plugs, convenience receptacles, and the point
where they exit from the apparatus.
11. Only use attachments/accessories specified by the
manufacturer.
12. Use only with a cart, stand, tripod, bracket,
or table specified by the manufacturer, or
sold with the apparatus. When a cart is
used, use caution when moving the cart/
apparatus combination to avoid injury
from tip-over.
13. Unplug this apparatus during lightning
storms or when unused for long periods of
time.
14. Refer all servicing to qualified service personnel. Servicing is
required when the apparatus has been damaged in any way,
such as power-supply cord or plug is damaged, liquid has been
spilled or objects have fallen into the apparatus, the apparatus
has been exposed to rain or moisture, does not operate
normally, or has been dropped.
15. WARNING: To reduce the risk of fire or electric shock, do not
expose this apparatus to rain or moisture. Do not place objects
filled with water, such as a vase, on the apparatus.
16. The AC mains plug is used as the power disconnect device
and it should remain readily accessible and operable during
intended use. In order to completely disconnect the apparatus
from power, the mains plug should be completely removed
from the AC outlet socket.
17. CAUTION: To reduce the risk of fire or explosion, do not expose
batteries to excessive heat such as sunshine, fire or other
— 1 —
heat sources.
Page 3
Included
Please make sure the following items are included.
AC Adapter
Manual
Main Unit
Wired Microphone
Audio/Video Cables
— 2 —
Page 4
Location of Controls (Top/Front)
1
2
3
4
5
10
11
12
13
14
6
7
8
9
1. Stop /PAIR Button
2. Pair Indicator
3. CDG/BT Button
4. Power Indicator
5. Power ON/OFF Button
6. MONITOR ON/OFF Button
7. Mic Holders
8. MIC VOLUME Control
9. A.V.C. (Auto Voice Control)
15
7
16
17
18
10. CD Compartment
11. Play/Pause Button
12. REPEAT/PROGRAM Button
13. Screen
14. Skip : Button
15. Skip 9 Button
16. ECHO Control
17. BALANCE Control
18. MASTER VOLUME Control
— 3 —
Page 5
Location of Controls (Rear)
1
2
3
1. MIC 2 Jack
2. MIC 1 Jack
3. LINE IN Jack
4. AUDIO OUT Jack (L)
5. DC IN Jack
6. AUDIO OUT Jack (R)
7. VIDEO OUT Jack
4
5
6
7
— 4 —
Page 6
Connection
Connecting the Microphone(s)
1
2
Connecting the Unit to a TV
Microphones:
Connect a microphone into MIC Jack 1 u
as well as MIC Jack 2 v (when desired).
Note: Do not drop or tap the Mic as
damage to the Mic or speakers may occur.
Do not twirl the microphone cord as it will
cause damage to the encased wiring.
To output the video, lyrics and
audio to your TV, perform the
following steps:
Connect the RCA video cable
(Yellow) to the VIDEO OUT jack
and the audio cables (White
and Red) to the AUDIO OUT
jacks located on the back of the
VIDEO OUT
(yellow)
AUDIO OUT
(white - L
red - R)
REAR VIEW OF TV
VIDEO
AUDIO
INPUT
INPUT
R L
Singing Machine.
Connect the opposite end of
the RCA video cable (Yellow) to
the VIDEO IN jack and the audio
cables (White and Red) to the
RCA cables
AUDIO IN on your TV.
Notes:
• This unit can be used with or without a TV.
• Also refer to the TV’s User Guide.
• To see the lyrics on the screen, you must use a CD+G disc.
• Audio/Video cables are included.
— 5 —
Page 7
Connection
Connecting to AC Power
Connecting to LINE IN Jack
AUDIO OUTPUT
/ HEADPHONE JACK
To External Unit
Insert the small end of the AC
adapter into the DC IN Jack on
the rear of the unit. Insert the
other end (with the 2 blades) into
a conveniently located AC outlet
having 120V AC, 60Hz.
Note:
Make all connections before
connecting to AC power.
Connect an external device
by using an appropriate cable
(3.5mm audio cable not included)
as shown.
LINE IN
Note:
See page 13 to select and use the
LINE IN function.
— 6 —
Page 8
Operation
Playing a CD
1
Connect the unit as described
1
previously. Press the Power
button to turn the unit on; the Power
indicator will light.
Lift open the CD door and insert a
2
CD or a CD+G by gently pressing it
on the center spindle. Then close the
CD door.
Notes:
2
• What is a CD+G?
A CD+G (CD+Graphics) is the
standard format for most karaoke
discs that will display the words on
the screen.
• Never place anything other than a
CD in the compartment, as foreign
objects can damage the unit.
• If no disc is inserted, “NO DISC” will
appear on the screen.
• If connected to a TV or other audio
source, adjust the volume of the TV
using its own volume control.
ON/OFF
3
4
— 7 —
Repeatedly press the CDG/BT
3
button to select the CDG/CD mode;
“READ” will appear when searching
the disc and then the total number of
tracks will appear.
Press the Play/Pause button to
4
start playback. If listening to a CD+G
file, press the MONITOR ON/OFF
button to view the image and lyrics
on the screen.
Page 9
Operation
Playing a CD (Continued)
5
6
Adjust the volume to a comfortable
5
level using the MASTER VOLUME
control.
Connect microphone(s) as shown
6
on page 5, and slide the ON/OFF
switch on the microphone to the ON
position.
Adjust the MIC VOLUME control
7
as desired. Increasing this control
will increase the volume of both
microphones.
7
Rotate the ECHO control to add an echo
8
effect to your voice. Rotate clockwise to
increase the echo effect.
AUTO VOICE CONTROL can be
9
activated by rotating the A.V.C.
(Auto Voice Control). The higher this
9
8
— 8 —
control is set to, the more the vocals
on the multiplex recording will be
muted when the singer starts to sing
through the microphone. When the
singer stops singing, the recorded
vocals on the multiplex recording will
resume to normal.
Page 10
Operation
Playing a CD (Continued)
10
11
Rotate the BALANCE control
10
Note: To use the BALANCE control, a
CD+G disc must be used, otherwise it will
operate as a standard BALANCE control.
11
SEARCH: When playing any
Note: SEARCH function only works on
CD not CD+G discs.
clockwise to hear the recorded
vocals from a multiplex recording
or counterclockwise to hear
the music only from a multiplex
recording.
SKIP: Advance or go back one
track by pressing the Skip 9/
Skip : buttons.
audio CD, press and hold the
Skip 9/Skip : button. The CD
will search at high speed in the
forward or backward direction.
Normal play will continue when
you release the button.
12
— 9 —
12
REPEAT: During playback,
the REPEAT/PROGRAM button
once during playback, will
appear in the display and the
current track will be repeated. To
repeat all tracks, press the
REPEAT/PROGRAM button
again, will appear. Press again
to cancel the Repeat feature;
will appear.
press
Page 11
Operation
Playing a CD (Continued)
13
13
14
PROGRAM:
13
Note: Press the
TWICE to stop and clear the program.
14
24 tracks for playback in any desired
order. While in Stop mode, press the
PROGRAM/REPEAT button; PROG
SET 00:XX (xx is the total number
of tracks) will appear in the display.
Select the first track using the
9
/Skip : buttons, then press the
PROGRAM/REPEAT button. Repeat
to set up to 24 tracks into memory.
When done, press the Play/Pause
button to start playback.
PAUSE: During playback, if you wish
to pause the disc momentarily, press
the
Play/Pause button
again to resume normal playback.
You can program up to
Stop </PAIR
button
Skip
. Press
16
15
— 10 —
15
16
Press the
stop playback.
Press the Power
turn the unit off.
Stop </PAIR
ON/OFF
button to
button to
Page 12
Operation
Please connect your Music Device
Your Music Device is connected
Please connect your Music Device
Your Music Device is connected
Using a Bluetooth Device
Connect the unit as described previously.
1
Press the
the unit on
Power
ON/OFF button to turn
; the Power indicator will light.
1
3
2
4
Repeatedly press the CDG/BT button to
2
select the Bluetooth; “BLUETOOTH” will
appear on the screen. The screen will show
your Bluetooth device is ready to connect
with a notification sound. If there is a
previously paired Bluetooth device around,
the unit will connect it automatically with
a successful pairing sound. If no previously
paired devices are present, connect as
shown in the next step.
Note: You can also press the Stop </PAIR
button to disconnect any paired devices in order
to pair another device.
Turn on your device’s Bluetooth option in
3
settings to search for a discoverable device
with a Bluetooth signal. Select “Singing
Machine” from the device results on the
Bluetooth menu.
Note: Also refer to the user manual of your
Bluetooth device for detailed instructions.
The Pair indicator will light and a successful
4
pairing sound will be heard.
Notes:
• If your Bluetooth prompts you for a
passcode during the pairing process, please
enter “0000” to connect.
• On some Bluetooth devices, once pairing is
complete, select your Bluetooth device as
“Use as Audio Device” or similar.
• If connection is lost after successful pairing,
check to make sure the distance between
speaker and Bluetooth-enabled device does
not exceed 30 feet/10 meters.
• “BLUETOOTH” will blink on TV screen, and
will stop blinking after successful connection.
— 11 —
Page 13
Operation
Using a Bluetooth Device (Continued)
6
7
To control your Bluetooth device from
5
this unit, press the Play/Pause
button
to start playback (music app
5
must be open). Press the Play/Pause
button
during playback to pause the
song.
Adjust the volume to a comfortable level
6
using the MASTER VOLUME control on
this unit as well as the volume on your
Bluetooth device.
Connect microphone(s) as shown on
7
page 5, and slide the ON/OFF switch on
the microphone to the ON position.
Adjust the MIC VOLUME control
8
as desired. Increasing this control
will increase the volume of both
microphones.
12
Rotate the ECHO control to add an echo
9
effect to your voice. Rotate towards MAX to
8
9
11
10
— 12 —
increase the echo effect.
Adjust the BALANCE control to
10
11
12
move the audio from the left to right
speaker or vice-versa.
SKIP: Advance or go back one track
by pressing the Skip Back 9/Skip
Forward : buttons.
Press the Power
turn the unit off.
ON/OFF
button to
Page 14
Operation
Using the LINE IN Jack
1
LINE IN
Connect the unit as described
1
previously (see page 6). Press the
Power
ON/OFF
on; the Power indicator will light.
Connect the external unit to the
2
LINE IN Jack on the back of this unit.
Connecting an external unit will allow
the audio to be played through your
Singing Machine. LINE IN function is
automatically selected once the audio
cable is plugged in.
Notes:
2
• It is highly recommended to set the
volume on the auxiliary unit to 1/3 or
lower to avoid distortion.
• Skipping files/tracks is not possible on
this unit when using an external device.
button to turn the unit
Adjust the volume using the MASTER
3
VOLUME control on this unit or your
external device’s volume control.
3
Connect microphone(s) as shown on
4
page 5. Slide the ON/OFF switch on
the microphone to the ON position.
— 13 —
Page 15
Operation
Using the LINE IN Jack (Continued)
5 6
8
Adjust the MIC VOLUME control
5
as desired. Increasing this control
will increase the volume of both
microphones.
Rotate the ECHO control to add an echo
6
effect to your voice. Rotate clockwise to
increase the echo effect.
Adjust the BALANCE control to move
7
the audio from the left to right speaker
or vice-versa.
Press the power ON/OFF button to
8
7
turn the unit off.
— 14 —
Page 16
Troubleshooting Guide
Should this unit exhibit a problem, check the following before seeking service:
No Power
• Power is not on; press the
• Confirm that the AC adapter is connected securely to the back of the unit.
• Connect the unit to a different outlet.
No Sound – General
• Master Volume is set to minimum; raise volume.
• Correct Function was not selected; press the CDG/BT button to change the function.
• If using an external device, raise the volume.
.
No Sound – If connected to a TV
• Volume on the TV is muted or too low.
• Correct source (usually AV) was not selected on the TV’s menu.
No sound from the microphone
• Make sure the microphone is firmly connected to the MIC 1 or MIC 2 jack.
• Make sure the ON/OFF switch on the microphone is set to the ON position.
• Make sure the MIC VOLUME control is not set too low.
• MASTER VOLUME is set to minimum; raise volume.
• Raise the Echo control past mid point.
Power
ON/OFF button to turn unit ON.
The Bluetooth device cannot be paired or connected with the unit
• You have not activated the Bluetooth function of your device; see page 11 or refer to
the Bluetooth device user’s manual.
• The system is not in pairing mode; press the Stop </PAIR button to restart pairing.
The Music is not available on the unit after successfully connecting the Bluetooth
• Ensure your Bluetooth device can support the A2DP Bluetooth profile.
• The volume on the external Bluetooth device is set too low or muted; raise as desired.
• Make sure your music’s application is open.
— 15 —
Page 17
Specifications
AUDIO
OUTPUT POWER (MAXIMUM) ................................................................................3.5 Watts (RMS)
OUTPUT IMPEDANCE ..................................................................................................................3 Ohms
CD PLAYER SECTION
FREQUENCY RESPONSE .............................................................................................. 100Hz - 20kHz
SIGNAL-TO-NOISE RATIO ............................................................................................................... 50dB
NUMBER OF PROGRAMS ...................................................24 Step Random Access Programming
SAMPLING SYSTEM.........................................................................................8 Times Over Sampling
BLUETOOTH
Bluetooth Version .....................................................................................................................V2.1+EDR
Working Distance ...........................................Up to 30 feet/10 meters measured in open space
AUX IN SECTION ...........................................................................3.5 mm Stereo Headphone Jack
MICROPHONE ....................-74db 600 Ohm Impedance with 6.3 mm Dynamic Microphone
POWER SECTION ...............................................................................................................DC 5.8V, 2A
DIMENSIONS (HxWxD) ..........................................................................9.1 x 8.7 x 13.4 inches /
.......................................................................................................................................23 x 22.2 x 34 cm
WEIGHT ............................................................................................................................ 5.06lbs/2.3kgs
Specifications are subject to change without notice.
— 16 —
Page 18
Shop for Accessories on Our Website:
www.singingmachine.com
The Singing Machine Company, Inc.
4060 E Jurupa Street, Unit B
Ontario, CA 91761-1413 USA
Copyright © 2016 All Rights Reserved.
— 17 —
PRINTED IN CHINA
xxxx-xxx-ENG01
Loading...