1
Instructions for Use
DO105625B
2
Treating with Silk’n FaceFX for
the First Time
The skin should be, clean, dry and free of any powder, gel or
cream. If necessary a light oil based serum may be applied thinly
to the skin to help glide the device. Allow serum to absorb into
the skin before treating. See “cleaning the Silk’n Face” chapter.
Press the
POWER ON/OFF SWITCH. The green READY/TREATMENT
INDICATOR LIGHT
(I) will start blinking, and shortly afterwards
will be lit steadily.
Your FaceFX is ready for treatment.
Place the
TREATMENT SURFACE on your skin. The LED light will
automatically activate.
Apply light pressure while slowly moving the FaceFX
APPLICATOR in small circular motions. The TREATMENT SURFACE
temperature will slowly increase.
Perform the treatment for 5-7 minutes on each area.
It is recommended to apply a small amount of a moisturizing
cream on the treated skin areas after each session and to
massage it gently in circular motions.
3
Table of Contents
Before You Start.......................................................................................................................................4
What is Silk’n FaceFX?..................................................................................................................................4
Silk’n FaceFX device description..........................................................................................................4
Package contents.............................................................................................................................................5
Safety with Silk’n FaceFX..................................................................................................................6
When to avoid using Silk’n FaceFX?...................................................................................................6
Reducing the risk of injury..........................................................................................................................7
Possible side eects using FaceFX........................................................................................................7
Protect your Silk’n FaceFX......................................................................................................................8
Skin Treatment the FaceFX Way...........................................................................................9
The benefits of Silk’n FaceFX......................................................................................................................9
Silk’n FaceFX facial treatment areas....................................................................................................9
First Steps with Silk’n FaceFX.......................................................................................................9
Silk’n FaceFX setup.......................................................................................................................................9
Plan your Silk’n FaceFX treatment for best results....................................................................10
Treating with Silk’n FaceFX for the first time...............................................................................11
What to expect when treating with Silk’n FaceFX?..................................................................12
After treating with Silk’n FaceFX.......................................................................................................12
Maintenance of Silk’n FaceFX....................................................................................................13
Cleaning Silk’n FaceFX...............................................................................................................................13
Storage.............................................................................................................................................13
To protect the environment................................................................................................................13
Troubleshooting...........................................................................................................................14
Customer Service.................................................................................................................................15
Specifications............................................................................................................................................16
Labeling..........................................................................................................................................................17
EMC Testing Summary Results...............................................................................................18
EMC Testing Summary Results
4
Before You Start
Before using Silk’n FaceFX for the first time, please read this
manual in its entirety. Pay particular attention to sections on device
use procedures, device operation, and after-use procedures.
What is Silk’n FaceFX?
Silk’n FaceFX is a hand held light emitting diode (LED) device for
facial treatments of periorbital wrinkles, reducing pore size and
temporary improvement of the appearance of the skin. The light
emitted by Silk’n FaceFX stimulates deep skin tissue and achieves
facial rejuvenation.
Typical areas for Silk’n FaceFX treatment are the neck, the cheeks,
the forehead, and around the eyes.
Silk’n FaceFX device description
Silk’n FaceFX device consists of an APPLICATOR and an ADAPTOR.
Silk’n FaceFX
APPLICATOR is a hand held unit that contains TREATMENT
SURFACE
at the APPLICATOR tip,
ON/OFF SWITCH
and INDICATOR PANEL.
5
Package contents
Upon opening the Silk’n FaceFX package, you will find the
following:
FaceFX
APPLICATOR
Adaptor
User manual
L
G
K
J
A Treatment surface
B On/o Switch
C Indicators Panel
D Applicator
E Plug
F Adaptor
G StandBy - indicator light
L
System Error - indicator light
K
Ready/Treatment - indicator light
J
Spare - indicator light
The green Ready/Treatment - indicator light (K) illuminates when
pressing the ON/OFF switch.
The green StandBy - indicator light (G) illuminates when the
device is turned o.
The yellow System Error - indicator light (L) illuminates when a
system error/malfunction occurs.
6
Safety with Silk’n FaceFX
To protect your skin, a temperature sensor is embedded in the
treatment tip of the Silk’n FaceFX. This sensor ensures the skin’s
surface will not exceed 41°C / 106°F.
When to avoid using Silk’n FaceFX?
Certain conditions may temporarily prevent the use of Silk’n
FaceFX. Avoid using Silk’n FaceFX:
on raised dark brown or black spots, birth marks, moles or
warts, lesions, open wounds or active infections, such as cold
sores. Wait for the aected area to heal before treating.
on abnormal skin conditions caused by diabetes or
other systemic or metabolic diseases.
on treatment areas if you have a history of herpes outbreaks
in the area of treatment, unless you have consulted your
physician and received preventative medication prior to use.
if your facial skin has been treated with a physician-prescribed
drug within the past 6 month (please consult with your
physician).
7
Reducing the risk of injury
• Keep Silk’n FaceFX out of the reach of children.
• Keep Silk’n FaceFX out of the reach of persons with reduced
physical, sensory or mental capabilities.
• Keep Silk’n FaceFX away from water!
Do not use or store Silk’n FaceFX in a wet environment
(e.g. near a shower or a bathtub)!
• Keep the device and its adaptor dry!
• Do not use Silk’n FaceFX if the
ADAPTOR or the APPLICATOR is damaged!
• If the
APPLICATOR is damaged, make sure it is replaced with an
original part from Home Skinovations!
• The
APPLICATOR contains a dedicated transformer. Never replace
the
APPLICATOR with another plug!
If you are unsure if FaceFX is safe for you to use, please consult
with your doctor or dermatologist.
Possible side eects using FaceFX
When used according to the instructions, side eects and
complications associated with use of Silk’n FaceFX are rare.
However every cosmetic procedure, including those designed for
home use, involve some degree of risk. Therefore it is important
that you understand and accept the risks and complications that
can occur with energy based systems designed for home use.
Silk’n FaceFX treatments are generally very well-tolerated. Most
users sense the moderate heat applied by the device during use,
with no further discomfort.
• Minor Skin Discomfort
Your skin may become slightly irritated after using Silk’n FaceFX.
This is a typical and transient phenomenon. If the irritation does
not disappear within three days, please consult a physician or a
dermatologist.
8
• Skin Redness
Your skin may become slightly red right after using FaceFX. This
should disappear a few hours after treatment.
Protect your Silk’n FaceFX
• Store the device in a clean area free of dust.
• Do not cover the ventilation slots during use.
• Never shake or drop Silk’n FaceFX or subject it to severe
shocks.
• Silk’n FaceFX is sensitive to environmental temperature during use.
Do not expose the FaceFX to environmental temperatures
lower than 15°C / 59°F or higher than 35°C / 95°F during use.
• Silk’n FaceFX can not tolerate extreme change of temperature.
When moved from a cold environment (under 10°C / 50°F) to
a warm environment, avoid use for approximately 3 hours.
• Do not expose Silk’n FaceFX to direct sunlight or UV light for
long periods of time.
• Silk’n FaceFX is designed for occasional home use (as opposed
to exhaustive commercial or professional use). Avoid such
exhaustive use.
9
Skin Treatment the FaceFX Way
The benefits of Silk’n FaceFX
The outcome of using Silk’n FaceFX when following instructions
correctly will be the reduction of facial fine lines, reducing pore
size and improving the appearance of the face.
Best results can be expected 3-7 weeks after completing the
recommended course of treatment.
Silk’n FaceFX facial treatment areas
Typical areas for Silk’n FaceFX treatment are the cheeks,
forehead, neck, and around the eyes.
First Steps with Silk’n FaceFX
Silk’n FaceFX Setup
1. Remove Silk’n FaceFX, APPLICATOR, ADAPTOR and other
components from box.
10
Plan your Silk’n FaceFX treatment for best results
The eciency of the results varies from person to person and
according to the frequency of use. Some may see results sooner
than others.
A single FaceFX session usually takes 15-20 minutes in which
you should gently glide the FaceFX applicator slowly over the
desired treatment area. During the procedure you should feel
gentle heat penetrating deep into the skin.
Initial Silk’n FaceFX treatment course: For the first month (4
weeks), treatment should be performed 3 times a week for 1520 minutes each time. (5-7 minutes on each treatment zone).
Silk’n FaceFX maintenance regime:
Use Silk’n FaceFX once a week for 15-20 minutes.
11
Treating with Silk’n FaceFX for the First Time
The skin should be, clean, dry and free of any powder, gel or
cream.
If necessary a light oil based serum may be applied thinly to the
skin to help glide the device. Allow serum to absorb into the skin
before treating. See “cleaning the Silk’n FaceFX” section.
Remove Silk’n FaceFX
APPLICATOR from its package.
Press the
POWER ON/OFF SWITCH. The green READY/TREATMENT
INDICATOR LIGHT
(I) will start blinking, and shortly afterwards will
be lit steadily.
Your FaceFX is ready for treatment.
Place the
TREATMENT SURFACE on your skin. The LED light will
automatically activate.
Apply light pressure while slowly moving the FaceFX
APPLICATOR in small circular motions. The
TREATMENT SURFACE
temperature will slowly increase.
Perform the treatment
for 5-7 minutes on each
area.
It is recommended to
apply a small amount of
a moisturizing cream on
the treated skin areas
after each session and
to massage it gently in
circular motions.
12
What to expect when treating with Silk’n FaceFX?
During a Silk’n FaceFX session it is normal to experience and feel:
A Sensation of Warmth – During the Silk’n FaceFX session
you may feel slight warmth. This is normal and should
disappear up to an hour after the session.
Some Mild Red Color – After each Silk’n FaceFX session
you may notice a slight reddening of the skin (mild erythema)
over the treated area. This is normal and should fade within
an hour or two.
A Fan Noise - It is normal to hear a fan noise turning on and
o during FaceFX treatments. This is a safety feature that
helps regulate the skin temperature during use.
Best results can be expected 3-7 weeks after completing the
recommended course of treatment.
After treating with Silk’n FaceFX
When FaceFX session has been completed turn FaceFX o by
pressing the
POWER ON/OFF SWITCH.
After each session it is recommended that you clean your
FaceFX device, (See Section: “Cleaning FaceFX”).
13
Maintenance of Silk’n FaceFX
Cleaning the Silk’n FaceFX
After each session, it is recommended to clean your Silk’n
FaceFX device:
• Turn Silk’n FaceFX o by pressing the
POWER ON/OFF SWITCH.
• Unplug Silk’n FaceFX from the electrical outlet
• Allow cooling down of its
TREATMENT SURFACE.
• Use a dry, clean cloth and a specially formulated cleaner for
electronic equipment to gently wipe the device and especially its
TREATMENT SURFACE.
• Never immerse Silk’n FaceFX or any of its parts in water!
• Never clean the FaceFX or any of its parts under the
tap or in the dishwasher.
Storage
• Store the clean device and all its parts in a dry place, at a
temperature of between -10°C to 60°C / 14°F to 140°F
To protect the environment
Do not discard Silk’n FaceFX with the normal household waste.
Dispose of it at an ocial recycling collection point.
Please call your local recycling depot for locations and
proper recycling instructions.
14
Troubleshooting
This chapter summarizes the most common problems you
could encounter. If you are unable to solve the problem with the
information below, contact your local Silk’n Customer Service
Center for further support.
SolutionPossible CauseProblem
Plug the adaptor to AC electrical outlet, and
connect the Plug (E) to the Applicator
The Adaptor is not
connected
Silk'n Clear does not
work
Contact your local Silk’n customer
Service center
The Applicator is
broken
Plug the adaptor to AC electrical outlet, and
connect the Plug (E) to the Applicator
The Adaptor is not
connected properly
Silk'n Clear suddenly
switches o
No action is required
This is normal
Device temperature
rises during use.
No action is required
This is normal
Press the ON/OFF Switch twice to switch
the Applicator o and on again. If Ready/
Treatment Mode - indicator light (K) does
not illuminate again, contact your local Silk’n
customer Service center
The Applicator
needs to be reset
Ready/Treatment
Mode - indicator
light (K) does not
illuminate when
pressing the ON/
OFF Switch
Press the ON/OFF Switch twice to switch the
Applicator o and on again. If System Error
- indicator light (L) illuminates again, contact
your local Silk’n customer Service center
Malfunction of the
Applicator
The Yellow System
Error - indicator
light (L) is lit.
15
Customer Service
For USA and Canada customers:
For more information about Silk’n™ products please visit
www.silkn.com.
If your device is broken, damaged, in need of repair, or for any
other user assistance, please contact Silk’n™ Customer Service:
1-877-DO-SILKN / 1-877-367-4556, contact@silkn.com
International Customers:
For more information about Silk’n products or to find a list of
International Silk’n websites please visit www.silkn.eu or
www.silkn.com.
If your device is broken, damaged, in need of repair, or for
any other user assistance, please contact your local Silk’n™
Customer Service or write to: info@silkn.com (International) or
contact@silkn.com (US and Canada).
Manufacturer:
Home Skinovations Ltd.
Tavor Building, Shaar Yokneam POB 533
Yokneam 20692
ISRAEL
16
Rated voltage (Adaptor) 100V - 240V
Model: KSA24A1200150Hx
Rated frequency (Adaptor) 50Hz/60Hz
Rated (Adaptor) 12Vdc; 1500 mA
Applied part Type BF
Protecting rating IP30 (EN60529)
Storage condition Temperature: -40°C to 70°C /-40°F to 158°F
Relative humidity: 10% - 90%
Atmospheric pressure: 500 to 1060 hPa
Classified standard IEC 60601-1-2:2007
EN 60601-1-2:2007
Operating condition Temperature: 10°C to 35°C / 50°F to 95°F
Relative humidity: 15% to 90%
Atmospheric pressure: 700 to 1060 hPa
Light source Light Emitting Diodes
Wavelengths peak emission wavelength: 635nm
Degree of protection
against electric shock
Class II.
Specifications
17
Labeling
Degree of protection against electric shock: type BF applied part
WEEE - Waste Electrical and Electronic Equipment
CSA Mark
CE Mark
Keep dry
Manufacturer
Authorized Representative in the European Community
Degree of protection against ingress water:
IP30 ordinary
This device is not suitable for use in the presence of
flammable anesthetic mixture with air or with Oxygen or
Nitrous Oxide.
The symbol on the label axed to this device means
“Attention, consult accompanying documents”.
18
EMC Testing Summary Results
19
Tavor Building, Shaar Yokneam POB 533
Yokneam 20692, ISRAEL
tel. +972-4-9097470, fax +972-4-9097471
info@silkn.com, contact@silkn.com
www.silkn.com
Loading...