Siemens SCALANCE X-200, SCALANCE XF200, X204-2, X204-2TS, X204-2FM Operating Instructions Manual

...

Download

SCALANCE X-200

___________________

SIMATIC NET

Industrial Ethernet Switches SCALANCE X-200

Operating Instructions

03/2015

C79000

-G8976-C284-06

Preface

Functions

Description of the device

Safety notices

Installation

Connecting up

Approvals

Technical specifications

Dimension drawings

Test of mechanical stability

Training, Service & Support

Siemens AG Division Digital Factory Postfach 48 48 90026 NÜRNBERG GERMANY

C79000-G8976-C284-06

Ⓟ

03/2015 Subject to change

Legal information

Warning notice system

This manual contains notices you have to observe in order to ensure your personal safety, as well as to prevent damage to property. The notices referring to your personal safety are highlighted in the manual by a safety alert symbol, notices referring only to property damage have no safety alert symbol. These notices shown below are graded according to the degree of danger.

DANGER

indicates that death or severe personal injury will result if proper precautions are not taken.

WARNING

indicates that death or severe personal injury may result if proper precautions are not taken.

CAUTION

indicates that minor personal injury can result if proper precautions are not taken.

NOTICE

indicates that property damage can result if proper precautions are not taken.

If more than one degree of danger is present, the warning notice representing the highest degree of danger will be used. A notice warning of injury to persons with a safety alert symbol may also include a warning relating to property damage.

Qualified Personnel

The product/system described in this documentation may be operated only by

personnel qualified

for the specific task in accordance with the relevant documentation, in particular its warning notices and safety instructions. Qualified personnel are those who, based on their training and experience, are capable of identifying risks and avoiding potential hazards when working with these products/systems.

Proper use of Siemens products

Note the following:

WARNING

Siemens products may only be used for the applications described in the catalog and in the relevant technical

documentation. If products and components from other manufacturers are used, these must be recommended or approved by Siemens. Proper transport, storage, installation, assembly, commissioning, operation and maintenance are required to ensure that the products operate safely and without any problems. The permissible

ambient conditions must be complied with. The information in the relevant documentation must be observed.

Trademarks

All names identified by ® are registered trademarks of Siemens AG. The remaining trademarks in this publication may be trademarks whose use by third parties for their own purposes could violate the rights of the owner.

Disclaimer of Liability

We have reviewed the contents of this publication to ensure consistency with the hardware and software described. Since variance cannot be precluded entirely, we cannot guarantee full consistency. However, the information in this publication is reviewed regularly and any necessary corrections are included in subsequent editions.

SCALANCE X-200 Operating Instructions, 03/2015, C79000-G8976-C284-06

Preface

Components of the product

The following components are supplied with a

SCALANCE X-200

IE switch:

● One device

● One 2-pin plug-in terminal block

● One 4-pin plug-in terminal block

● One DVD (configuration manual, operating instructions, Primary Setup Tool, GSD file,

SNMP OPC profile)

The following components are supplied with a

SCALANCE X-200

IE switch with the

PRO

supplement:

● One device

● Protective caps for the data interfaces

● Protective caps for the connectors of the power supply

● One protective cap for the signaling contact

● One DVD (configuration manual, operating instructions, Primary Setup Tool, GSD file,

SNMP OPC profile)

Unpacking, checking

WARNING

Do not use any parts that show evidence of damage. If you use damaged parts, there is no guarantee that the device will function according to the specification.

If you use damaged parts, this can lead to the following problems:

• Injury to persons

• Loss of the approvals

• Violation of the EMC regulations

Use only undamaged parts.

1. Make sure that the package is complete.

2. Check all the parts for transport damage.

If the consignment is incomplete or damaged, contact your supplier or your local Siemens office.

Preface

SCALANCE X-200

4 Operating Instructions, 03/2015, C79000-G8976-C284-06

Purpose of the Operating Instructions

These operating instructions support you when commissioning networks with the devices of the product line SCALANCE X-200.

Overview of the technical documentation of the IE Switches X-200

The technical documentation of the X-200 product line is divided into hardware and software and can be found in the following documents:

●

PH SCALANCE X-200 configuration manual

Software description of the X-200 product line

●

SCALANCE X-200 BA Operating Instructions

Hardware description for all product groups and general information.

You will find the documents here:

● On the data medium that ships with some products:

– Product CD / product DVD

– SIMATIC NET Manual Collection

● On the Internet pages of Siemens Industry Online Support (http://support.automation.siemens.com/WW/view/en/33118791/133300

Validity of the Operating Instructions

These operating instructions are valid for the following devices:

SCALANCE X200 and SCALANCE XF200

Product name:

Order number:

X204-2 6GK5 204-2BB10-2AA3

X204-2TS

6GK5 204-2BB10-2CA2

X204-2FM

6GK5 204-2BB11-2AA3

X204-2LD

6GK5 204-2BC10-2AA3

X204-2LD TS

6GK5 204-2BC10-2CA2

X206-1

6GK5 206-1BB10-2AA3

X206-1LD

6GK5 206-1BC10-2AA3

X208

6GK5 208-0BA10-2AA3

X208PRO

6GK5 208-0HA10-2AA6

X212-2

6GK5 212-2BB00-2AA3

X212-2LD

6GK5 212-2BC00-2AA3

X216

6GK5 216-0BA00-2AA3

X224

6GK5 224-0BA00-2AA3

Flat design:

XF204

6GK5 204-0BA00-2AF2

XF204-2

6GK5 204-2BC00-2AF2

Preface

SCALANCE X-200 Operating Instructions, 03/2015, C79000-G8976-C284-06

SCALANCE X200 and SCALANCE XF200

XF206-1

6GK5 206-1BC00-2AF2

XF208 6GK5 208-0BA00-2AF2

SCALANCE X200IRT and XF200IRT

Product name:

Order number:

X200-4P IRT 6GK5 200-4AH00-2BA3

X201-3P IRT

6GK5 201-3BH00-2BA3

X201-3P IRT PRO

6GK5 201-3JR00-2BA6

X202-2IRT

6GK5 202-2BB00-2BA3

X202-2P IRT

6GK5 202-2BH00-2BA3

X202-2P IRT PRO

6GK5 202-2JR00-2BA6

X204IRT

6GK5 204-0BA00-2BA3

X204IRT PRO

6GK5 204-0JA00-2BA6

Flat design:

XF204IRT

6GK5 204-0BA00-2BF2

Purpose

The SCALANCE X-200 devices are switches for setting up Ethernet networks for industrial applications.

Restricted area of application according to Hazardous Locations (HazLoc)

The devices are only suitable for use in the following areas:

● In areas according to Class I, Division 2, Groups A, B, C and D and in areas without

explosive atmospheres.

● In areas according to Class I, Zone 2 Groups IIC and in areas without explosive

atmospheres.

Names of the devices in these operating instructions

Unless mentioned otherwise, the descriptions in these operating instructions refer to all devices of the SCALANCE X-200 product line named above in the section on Validity.

In the remainder of the instructions, these will also be referred to as

IE switches

or also

simply as

X-200

Preface

SCALANCE X-200

6 Operating Instructions, 03/2015, C79000-G8976-C284-06

Further documentation

In the system manuals "Industrial Ethernet / PROFINET Industrial Ethernet" and "Industrial Ethernet / PROFINET passive network components", you will find information on other SIMATIC NET products that you can operate along with the devices of this product line in an Industrial Ethernet network.

You will find the system manuals on the Internet pages of Siemens Industry Online Support under the following entry IDs:

● 27069465 (http://support.automation.siemens.com/WW/view/en/27069465

)

Industrial Ethernet / PROFINET Industrial Ethernet System Manual

● 84922825 (http://support.automation.siemens.com/WW/view/en/84922825) Industrial Ethernet / PROFINET - Passive network components System Manual

Finding information

To help orientation, there is not only a table of contents but also an Index in the Appendix.

The SIMATIC NET Glossary also provides additional help, see below.

Audience

These operating instructions are intended for persons involved in commissioning networks in which IE switches are used.

SIMATIC NET Selection Tool

The SIMATIC NET selection tool supports you when selecting Industrial Ethernet switches and components for Industrial Wireless Communication. You will find current information on the Product Support pages under the following entry ID:

39134641 (http://support.automation.siemens.com/WW/view/en/39134641

)

Preface

SCALANCE X-200 Operating Instructions, 03/2015, C79000-G8976-C284-06

Where to find Siemens documentation

● Article numbers

You will find the article numbers for the Siemens products of relevance here in the following catalogs:

– SIMATIC NET - Industrial Communication / Industrial Identification, catalog IK PI

– SIMATIC - Products for Totally Integrated Automation and Micro Automation, catalog

ST 70

You can request the catalogs and additional information from your Siemens representative. You will also find the product information in the Siemens Industry Mall at the following address:

(https://mall.industry.siemens.com

)

● Manuals on the Internet

You will find SIMATIC NET manuals on the Internet pages of Siemens Industry Online Support:

Link to Customer Support (http://support.automation.siemens.com/WW/view/en

)

Enter the entry ID of the relevant manual as the search item. The entry ID is specified in the references.

As an alternative, you will find the SIMATIC NET documentation on the pages of Product Support:

10805878 (http://support.automation.siemens.com/WW/view/en/10805878

)

Go to the required product group and make the following settings:

"Entry list" tab, Entry type "Manuals / Operating Instructions"

● Manuals on the data medium

You will often find manuals of SIMATIC NET products on the data medium that ships with many of the SIMATIC NET products.

Security information

Siemens provides products and solutions with industrial security functions that support the secure operation of plants, solutions, machines, equipment and/or networks. They are important components in a holistic industrial security concept. With this in mind, Siemens’ products and solutions undergo continuous development. Siemens recommends strongly that you regularly check for product updates.

For the secure operation of Siemens products and solutions, it is necessary to take suitable preventive action (e.g. cell protection concept) and integrate each component into a holistic, state-of-the-art industrial security concept. Third-party products that may be in use should also be considered. For more information about industrial security, visit http://www.siemens.com/industrialsecurity.

To stay informed about product updates as they occur, sign up for a product-specific newsletter. For more information, visit http://support.automation.siemens.com.

Preface

SCALANCE X-200

8 Operating Instructions, 03/2015, C79000-G8976-C284-06

SIMATIC NET glossary

Explanations of many of the specialist terms used in this documentation can be found in the SIMATIC NET glossary.

You will find the SIMATIC NET glossary here:

● SIMATIC NET Manual Collection or product DVD

The DVD ships with certain SIMATIC NET products.

● On the Internet under the following entry ID:

50305045 (http://support.automation.siemens.com/WW/view/en/50305045

)

Trademarks

The following and possibly other names not identified by the registered trademark sign ® are registered trademarks of Siemens AG:

SIMATIC NET, SCALANCE, C-PLUG, OLM

SCALANCE X-200 Operating Instructions, 03/2015, C79000-G8976-C284-06

Table of contents

Preface ...................................................................................................................................................... 3

1 Functions ................................................................................................................................................. 11

2 Description of the device ......................................................................................................................... 15

2.1 Device views ........................................................................................................................... 15

2.2 The LEDs ................................................................................................................................ 17

2.2.1 LED display when the device starts up ................................................................................... 17

2.2.2 Power LED "L" (green/yellow LED) ........................................................................................ 17

2.2.3 Fault LED "F" (yellow/red LED) .............................................................................................. 18

2.2.4 Redundancy manager LED "RM" (green LED) ...................................................................... 18

2.2.5 Standby LED "RM" (yellow LED) ............................................................................................ 19

2.2.6 Port LEDs "P" (green/yellow LEDs) ........................................................................................ 20

2.2.7 Diagnostics LEDs for optical connectors "F" (yellow LED) ..................................................... 20

2.2.8 Show Location ........................................................................................................................ 20

2.3 The SET button ....................................................................................................................... 21

2.4 The C-PLUG ........................................................................................................................... 22

3 Safety notices .......................................................................................................................................... 27

3.1 Safety notices in general ........................................................................................................ 27

3.2 Safety notices for hazardous areas ........................................................................................ 29

3.3 Security recommendations ..................................................................................................... 30

4 Installation ............................................................................................................................................... 33

4.1 Safety notices for installation .................................................................................................. 33

4.2 Installation options .................................................................................................................. 36

4.3 Installation on a DIN rail .......................................................................................................... 37

4.4 Installation on a standard rail .................................................................................................. 38

4.5 Wall mounting ......................................................................................................................... 39

5 Connecting up ......................................................................................................................................... 41

5.1 Safety when connecting up ..................................................................................................... 41

5.2 Power supply .......................................................................................................................... 44

5.2.1 Power supply via terminal block ............................................................................................. 44

5.2.2 Supply for X208PRO .............................................................................................................. 45

5.2.3 Supply for IRT-PRO devices ................................................................................................... 45

5.3 Grounding ............................................................................................................................... 48

5.4 Signaling contact ..................................................................................................................... 49

5.5 Attachment to Industrial Ethernet ........................................................................................... 51

5.5.1 Electrical connections ............................................................................................................. 51

Table of contents

SCALANCE X-200

10 Operating Instructions, 03/2015, C79000-G8976-C284-06

5.5.1.1 Electrical attachments to Industrial Ethernet ......................................................................... 51

5.5.1.2 Electrical connectors of the X208PRO .................................................................................. 53

5.5.2 Optical attachments to Industrial Ethernet ............................................................................. 55

5.5.2.1 Multimode fiber-optic cable .................................................................................................... 55

5.5.2.2 Single mode fiber-optic cable ................................................................................................. 56

5.5.2.3 POF and PCF cables ............................................................................................................. 56

5.5.3 Push-pull connector for IRT-PRO devices ............................................................................. 58

6 Approvals ................................................................................................................................................. 59

7 Technical specifications ........................................................................................................................... 67

A Dimension drawings ................................................................................................................................ 77

B Test of mechanical stability ...................................................................................................................... 83

C Training, Service & Support ..................................................................................................................... 85

Index ........................................................................................................................................................ 87

SCALANCE X-200 Operating Instructions, 03/2015, C79000-G8976-C284-06

Functions of the X-200 IE Switches

The X-200 IE switches are ideally suited for setting up Industrial Ethernet networks in bus, star and ring structures with transmission rates of 10/100 Mbps. All X-200 switches operate in the SIMATIC environment.

Hardware properties:

● X devices have a rugged metal housing and can be installed on a DIN rail, a standard rail

or directly on a wall.

● XF devices have a plastic housing and a flat design. They are suitable for installation on a

DIN rail.

● Redundant power supply, 2 x 24 VDC (exception: IRT-PRO devices)

● Diagnostics LED

● Signaling contact

● SET button for local configuration of the signaling contact

● Slot for C-PLUG

● Reliable plug-in connections thanks to rugged device connectors suitable for industry in

conjunction with PROFINET-compliant FastConnect plugs.

● TS devices meet the railway standard EN 50155

Software properties:

● PROFINET Diagnostics

● Topology support (LLDP)

● CLI - Command Line Interface / Telnet

● WBM - Web Based Management

● Configuration with STEP 7

● SNMP

● Ring redundancy including redundancy manager

● Passive Listening

● FM devices support the Fiber Monitoring Protocol and allow the monitoring of optical line

sections.

Functions

SCALANCE X-200

12 Operating Instructions, 03/2015, C79000-G8976-C284-06

Special features of the X-200IRT IE switches

The IRT variants were designed specifically for setting up Industrial Ethernet networks with isochronous/clock synchronous real-time communication. In addition to the properties named above, the IRT switches also provide the following functions:

● IRT communication based on the combination of the switching methods cut through and store and forward.

● Fast media redundancy thanks to an integrated redundancy manager for Fast Ethernet.

● Standby redundancy

Special features of the PRO variants

The devices with the "PRO" supplement are designed with degree of protection IP65/IP67 for use outside a cabinet.

Frame delay times

The number of IE Switches X-200 connected in a line influences the frame delay.

Note Frame delay time with X-200 without IRT

When a frame passes through X

-200 IE switches, it is delayed by the Store&Forward

fun

ction of the X-200 IE switches.

•

With a 64 byte frame length by approx. 10 microseconds (at 100 Mbps).

•

With a 1500 byte frame length by approx. 130 microseconds (at 100 Mbps).

This means that the more IE

Switch X-200 devices the frame passes through, the longer the

frame delay.

Note Frame delay time with X-200 with IRT

The more X

-200IRT IE switches a frame runs through, the higher the frame delay. By using

the "cut through" switching mechanism, the X

-200IRT IE switches are ideal to meet the real-

time requirements of PROFINET.

Cut through is, however, not possible:

•

Between a port set to 10 Mbps and a port set to 100 Mbps.

•

When two packets are to be sent at the same time on one port.

In this case, an X-200 IE switch changes to Store&Forward and the delay increases.

Functions

SCALANCE X-200 Operating Instructions, 03/2015, C79000-G8976-C284-06

Overview of the functions

The following table shows the hardware and software properties for each product variant of the X-200 switches in detail:

Number of electrical and optical connectors in the product name

The number before the hyphen in the product name indicates the number of electrical connectors. The number following the hyphen indicates the number of optical connectors of the device. For example, the switch X212-2 has twelve electrical and two optical connectors.

Functions

SCALANCE X-200

14 Operating Instructions, 03/2015, C79000-G8976-C284-06

SCALANCE X-200 Operating Instructions, 03/2015, C79000-G8976-C284-06

2.1

Device views

Device view based on the example of an X204-2TS

The following figure describes the individual components of an IE switch X200.

LEDs for attachments to Industrial Ethernet

2 LEDs

•

L: Power LED, power supply

•

F: Fault LED

•

RM: Redundancy manager or standby

Connector for signaling contact

Connector for power supply

SET button

Optical attachment to Industrial Ethernet

Electrical attachment to Industrial Ethernet

8 (on rear of device, not shown in figure:) Slot for C

PLUG

Description of the device

2.1 Device views

SCALANCE X-200

16 Operating Instructions, 03/2015, C79000-G8976-C284-06

Device view based on the example of an X202-2P IRT PRO

The following figure describes the individual components of a PRO version of an IE switch X-

200.

Electrical attachments to Industrial Ethernet

2 LEDs for electrical connectors

3 LEDs for optical connectors with diagnostics LEDs

4 LEDs

•

L: Power LED, power supply

•

F: Fault LED

•

RM:

– green = redundancy manager – yellow = standby indicator

Optical attachments to Industrial Ethernet

6 Connector for the power supply (supplied with L1, additionally looped through to L2)

Connector for signaling contact

8 Power supply for further devices (looped through from L1 to L2)

9 (on rear of device, not shown in figure): Slot for the C-PLUG and SET button

Device view based on the example of an XF204

The following figure describes the individual components of an IE switch X-200, flat design.

1 LEDs

•

L: Power LED, power supply

•

F: Fault LED

•

RM: Redundancy manager

Attachments to Industrial Ethernet

Connector for power supply

Connector for signaling contact

5 (behind the connectors, not shown in figure:) SET button

6 (on side of device, not shown in figure:) Slot for C-PLUG

7 LEDs for attachments to Industrial Ethernet

Description of the device

2.2 The LEDs

SCALANCE X-200 Operating Instructions, 03/2015, C79000-G8976-C284-06

2.2

The LEDs

2.2.1

LED display when the device starts up

When the X-200 starts up, the LEDs light up in the following sequence:

● The green power LED lights up immediately after turning on the device.

● The LEDs of the Ethernet connectors light up for approximately 6 seconds.

● When the Ethernet LEDs go off, the red fault LED is lit for approximately 20 seconds.

● Following this, after approximately 2 seconds the correct link status is displayed.

The X-200 is now ready for operation.

2.2.2

Power LED "L" (green/yellow LED)

The power LED shows the status of the power supply on the X-200 IE switch. The power LED can light up either green or yellow. The meanings of the display are as follows:

LED color

LED status

Meaning

Green

Lit

Both power supplies are connected; in other words, redundant power supply.

Yellow Lit Only one power supply is connected.

- Off No power supply is connected or the voltage is < 14 VDC or with TS devices < 8

VDC.

Note

The following devices do not have a redundant power supply:

•

X201-3P IRT PRO

•

X202-2P IRT PRO

•

X204IRT PRO

Description of the device

2.2 The LEDs

SCALANCE X-200

18 Operating Instructions, 03/2015, C79000-G8976-C284-06

2.2.3

Fault LED "F" (yellow/red LED)

The fault LED indicates a fault/error on the X-200. If the X-200 detects an error, the signaling contact is opened at the same time assuming that the response of the signaling contact was not configured differently.

The meanings of the fault LED display are as follows:

LED color

LED status

Meaning

Yellow Lit The LED can only adopt this status with FM devices.

Check the received power or the loss of power on optical connections. If necessary,

replace the parts.

Red Lit The fault LED lighting up can have the following meanings:

• Link down event on a monitored port

• Loss of the power supply

• C-PLUG error

• Device is in PROFINET mode:

– There is no connection to the controller. – There is a connection to the controller. A configured diagnostics interrupt is

also pending, for example power fail interrupt, C-PLUG interrupt etc.

• Redundancy manager connected through

• Switchover of standby connection

• A defined value was undershot in a monitored optical connection.

• A loop was detected.

• Device startup. The LED lights up for approximately 20 seconds.

Red Flashing Internal error detected. Notify maintenance personnel. If necessary, send the device

in for repair.

Off

No error detected.

2.2.4

Redundancy manager LED "RM" (green LED)

The green LED shows the following statuses of the X-200:

LED color

LED status

Meaning

Green Lit The device is operating in the role of redundancy manager. The ring is operating free

of errors. The monitoring is enabled.

Green Flashing The device is operating in the role of redundancy manager. An interruption was de-

tected in the ring. The device has switched through.

Off

The device is not operating in the role of redundancy manager.

Description of the device

2.2 The LEDs

SCALANCE X-200 Operating Instructions, 03/2015, C79000-G8976-C284-06

Note

This LED labeled on the device with "RM" has a dual function. The color of the display changes depending on the function:

•

If the LED is lit green, the redundancy manager function is indicated.

•

If the LED is lit yellow, the standby function is indicated.

Web Based Management (WBM), the LED is labeled differently depending on the

function:

•

The redundancy manager function (as shipped) is labeled "RM".

•

The standby function is labeled "SB" in the WBM.

2.2.5

Standby LED "RM" (yellow LED)

You will find the standby LED only on devices with the IRT function.

Note

This LED labeled on the device with "RM" has a dual function. The color of the display changes depending on the function:

•

If the LED is lit green, the redundancy manager function is indicated.

•

If the LED is lit yellow, the standby function is indicated.

Web Based Management (WBM), the LED is labeled differently depending on the

function:

•

The redundancy manager function (as shipped) is labeled "RM".

•

The standby function is labeled "SB" in the WBM.

The yellow LED indicates the following statuses of the X-200IRT:

LED color

LED status

Meaning

Yellow

Lit

The standby function is activated, the switch is in active mode.

Yellow

Flashes slowly

The standby function is activated, the switch is in passive mode.

Yellow

Flashes quickly

Standby partner lost.

Off

The standby function is not activated.

Description of the device

2.2 The LEDs

SCALANCE X-200

20 Operating Instructions, 03/2015, C79000-G8976-C284-06

2.2.6

Port LEDs "P" (green/yellow LEDs)

The LEDs of the Ethernet connectors can be lit green or yellow. The meanings of the display are as follows:

LED color

LED status

Meaning

Green

Lit

Link exists, no data reception

Yellow Lit Link exists, data being received

Device startup. The LED lights up for approximately 6 seconds.

Yellow

Flashing

Setting or display of the fault mask

The following statuses of the port LEDs do not exist on devices with the IRT function:

LED color

LED status

Meaning

Green flashes

once per period

Link exists and port in "blocking" status.

In this status, the port only receives management data (no user data).

Green flashes

three times per

period

Link exists and port is deactivated by the management. In this status, no data is sent or received via the port.

Green flashes

four times per

period

Port exists and is in the "monitor port" status. In this status, the data traffic of another port is mirrored to this port.

2.2.7

Diagnostics LEDs for optical connectors "F" (yellow LED)

You will find the diagnostics LEDs only on the devices with the IRT function.

The status of the optical connectors is indicated by an additional yellow LED per connector. The LEDs signal the following statuses:

LED color

LED status

Meaning

Yellow Lit Check the plug-in connection and the quality of the fiber-optic cable. If necessary,

replace the parts.

- Off Relevant only if the link exists. The existing link power margin is adequate for error-

free operation.

2.2.8

Show Location

Localizing an IE Switches X-200

To identify an IE Switch X-200 locally and with certainty, you can use the "show location" function on a programming device to select the node over the network and make it flash. This can be used, for example, when assigning addresses to make sure that the correct node receives the address. All port LEDs of the addressed node flash green at 2 Hz.

With the Primary Setup Tool (PST) V3.0 or higher, you can trigger this function with "Module \ Flash".

Description of the device

2.3 The SET button

SCALANCE X-200 Operating Instructions, 03/2015, C79000-G8976-C284-06

2.3

The SET button

Function of the SET button

With the SET button, you can change various settings of the device. The changed settings remain after cycling power to the device.

Different settings are made depending on how long you hold down the SET button, as described in the following table:

Figure 2-1 Phases for changing settings using the SET button

Phase

Description

1 The currently set fault mask is displayed. If no fault mask has been set, all ports flash one

after the other.

If you release the button in phase 1, this has no effect.

2 The LEDs of the ports at which there is currently a link flash at 2.5 Hz.

If you release the button in phase 2, this has no effect.

3 The LEDs of the ports at which there is currently a link and the LEDs of the connected pow-

er supply are lit permanently.

If you release the button in phase 3, the fault mask corresponding to the lit LEDs is adopted.

4 The RM LED flashes.

If you release the button in phase 4, the redundancy manager is deactivated. The redundancy function remains enabled. The device changes to "Automatic Redundancy Detect"

mode.

5 The RM LED is lit permanently.

If you release the button in phase 5, the redundancy function is activated and the device is

configured as HRP manager.

6 All LEDs flash.

The device is reset to the factory defaults.

Description of the device

2.4 The C-PLUG

SCALANCE X-200

22 Operating Instructions, 03/2015, C79000-G8976-C284-06

2.4

The C-PLUG

Area of application

The C-PLUG is an exchangeable medium for storage of the configuration and project engineering data of the basic device. This means that the configuration data remains available if the basic device is replaced.

How it works

Power is supplied by the basic device. The C-PLUG retains all data permanently when the power is turned off.

If an empty C-PLUG (factory settings) is inserted, all configuration data of an IE Switch X-200 is saved to it when the device starts up. Changes to the configuration during operation are also saved on the C-PLUG without any operator intervention being necessary.

If a C-PLUG is inserted, the configuration stored internally on the basic device is no longer changed. Al changes made to the configuration during ongoing operation are only stored on the C-PLUG.

A basic device with an inserted C-PLUG automatically uses the configuration data of the C-PLUG when it starts up. This is, however, only possible when the data was written by a compatible device type.

This allows fast and simple replacement of the basic device. If a device is replaced, the CPLUG is taken from the failed component and inserted in the replacement device. The first time it is started up, the replacement device has the same configuration as the failed device except for the MAC address set by the vendor.

Description of the device

2.4 The C-PLUG

SCALANCE X-200 Operating Instructions, 03/2015, C79000-G8976-C284-06

Compatible devices

As a general rule, the data on the C-PLUG is only compatible with devices having an identical order number and the same device name.

The device combinations shown in the following table are exceptions. With these devices, the exchange of the C-PLUG is possible in one direction.

Device type

C-PLUG created by device with order number

Compatible with device with order number

X204-2

6GK5 204-2BB00-2AA3

6GK5 204-2BB10-2AA3

X204-2LD 6GK5 204-2BC00-2AA3 6GK5 204-2BC10-2AA3

X206-1

6GK5 206-1BB00-2AA3

6GK5 206-1BB10-2AA3

X206-1LD

6GK5 206-1BC00-2AA3

6GK5 206-1BC10-2AA3

X208

6GK5 208-0BA00-2AA3

6GK5 208-0BA10-2AA3

X208PRO

6GK5 208-0HA00-2AA6

6GK5 208-0HA10-2AA6

Note

Combinations other than those shown in the table are not compatible with each other.

Note

If you insert a C

-PLUG in a compatible device, the system name of the original device is

entered both in the system name as well as in the PROFINET IO device name of the compatible device.

Using a previously written C-PLUG

If you want to insert a C-PLUG that has already been used and written to into a new differently configured X-200 IE switch, you will first need to delete the existing data on the CPLUG. You will find information about this in the configuration manual of the SCALANCE X200 in the section on the WBM menu items.

Note

The X

-200 IE switches normally start up with the configuration of the C-

PLUG, assuming this

was written to by a compatible device type. If the C

-PLUG was written to by an incompatible

device type, the basic device will not start up fully and signals an error. The WBM menu "System C

-PLUG" is displayed automatically. Here, use the "Modify C-PLUG" function to

specify whether or not the device operates

with a C-PLUG.

If you operate a device with a C

-PLUG, the C-PLUG can either be initialized with the factory

settings or with the settings stored internally on the device.

Description of the device

2.4 The C-PLUG

SCALANCE X-200

24 Operating Instructions, 03/2015, C79000-G8976-C284-06

Diagnostics

The following events are signaled by the diagnostics mechanisms of the X-200, such as LEDs, WBM etc.:

● Inserting a C-PLUG that contains the configuration of an incompatible device type.

● The accidental removal of a C-PLUG

● General malfunctions of the C-PLUG.

The C-PLUG does not ship with the product

The C-PLUG is not supplied with the X-200 IE switch. It is an optional accessory available under the following order number: 6GK1 900-0AB00.

Inserting in the slot

NOTICE

•

Insert and remove the C-PLUG only when power is off.

•

In a device with a varnished printed circuit board, you may only use a C-PLUG with a varnished board.

Figure 2-2 C-PLUG and slot

Description of the device

2.4 The C-PLUG

SCALANCE X-200 Operating Instructions, 03/2015, C79000-G8976-C284-06

The slot for the C-PLUG is located as follows:

● On the IE Switch X-200 on the back of the device.

● On the IE Switch XF-200 on the left hand side of the device.

Follow the steps below to insert the C-PLUG:

1. Remove the screw cover.

2. Insert the C-PLUG in the slot.

3. Close the slot with the screw cover.

Removing the C-PLUG

It is only necessary to remove the C-PLUG if the IE Switch X-200 develops a fault.

You can lever the C-PLUG out of the slot carefully using flat pliers, tweezers, or a small screwdriver.

If no C-PLUG is inserted in the device, when the device restarts, an error message is output in Web Based Management and in the Command Line Interface. In this case, you will need to set the device to operation without C-PLUG. For further information, refer to the section "System C-PLUG" in the section on the WBM menu in the configuration manual.

Description of the device

2.4 The C-PLUG

SCALANCE X-200

26 Operating Instructions, 03/2015, C79000-G8976-C284-06

SCALANCE X-200 Operating Instructions, 03/2015, C79000-G8976-C284-06

3.1

Safety notices in general

Note the following safety notices. These relate to the entire working life of the device.

WARNING

Do not use any parts that show evidence of damage

If you use damaged parts, there is no guarantee that the device will function according to the specification.

If you use damaged parts, this can lead to the following problems:

• Injury to persons

• Loss of the approvals

• Violation of the EMC regulations

• Damage to the device and other components

Use only undamaged parts.

Installation guidelines

The product meets the requirements if you adhere to the installation and safety notices contained in this documentation and in the following documentation when installing and operating the product.

Current documentation on the Internet

The current descriptions of the currently available products can be found on the Product Support pages under the entry IDs below:

● Configuration manual SIMATIC NET PH SCALANCE X-200

63203259 (http://support.automation.siemens.com/WW/view/en/63203259

)

● System manual SIMATIC NET Industrial Ethernet Network Manual

27069465 (http://support.automation.siemens.com/WW/view/en/27069465

)

● Configuration manual EMC Installation Guidelines

60612658 (http://support.automation.siemens.com/WW/view/en/60612658

)

Electrostatic discharge

To protect the product process from electrostatic discharge, personnel must first discharge any electrostatic charge from their body before touching the product.

Safety notices

3.1 Safety notices in general

SCALANCE X-200

28 Operating Instructions, 03/2015, C79000-G8976-C284-06

Special safety notices

You should also read the safety notices relating to handling in the individual sections, particularly in the sections "Installation" and "Connecting up".

Safety notices

3.2 Safety notices for hazardous areas

SCALANCE X-200 Operating Instructions, 03/2015, C79000-G8976-C284-06

3.2

Safety notices for hazardous areas

Safety notices on use in hazardous areas

General safety notices relating to protection against explosion

WARNING

EXPLOSION HAZARD

DO NOT OPEN WHEN ENERGIZED.

Safety notices when using the device according to Hazardous Locations (HazLoc)

If you use the device under HazLoc conditions you must also keep to the following safety notices in addition to the general safety notices for protection against explosion:

This equipment is suitable for use in Class I, Division 2, Groups A, B, C and D or nonhazardous locations only.

This equipment is suitable for use in Class I, Zone 2, Group IIC or non-hazardous locations only.

Safety notices

3.3 Security recommendations

SCALANCE X-200

30 Operating Instructions, 03/2015, C79000-G8976-C284-06

3.3

Security recommendations

To prevent unauthorized access, note the following security recommendations.

General

● You should make regular checks to make sure that the device meets these recommendations and/or other security guidelines.

● Evaluate your plant as a whole in terms of security. Use a cell protection concept with suitable products.

Physical access

● Limit physical access to the device to qualified personnel. The memory card or the C-PLUG contains sensitive data such as certificates, keys etc. that can be read out and modified.

● Lock unused physical ports on the device. Unused ports can be used to gain forbidden access to the plant.

Software (security functions)

● Keep the software up to date. Check regularly for security updates of the product. You will find information on this at: www.siemens.com/industrialsecurity (http://www.siemens.com/industrialsecurity

)

● Only activate protocols that you really require to use the device.

● Restrict access to the device with a firewall or rules in an access control list (ACL -

Access Control List).

● The option of VLAN structuring provides good protection against DoS attacks and unauthorized access. Check whether this is practical or useful in your environment.

● Enable logging functions. Use the central logging function to log changes and access attempts centrally. Check the logging information regularly.

● Configure a Syslog server to forward all logs to a central location.

Passwords

● Define rules for the use of devices and assignment of passwords.

● Regularly update passwords and keys to increase security.

● Change all default passwords for users before you operate the device.

● Only use passwords with a high password strength. Avoid weak passwords for example

password1, 123456789, abcdefgh.

● Make sure that all passwords are protected and inaccessible to unauthorized personnel.

● Do not use the same password for different users and systems or after it has expired.

Safety notices

3.3 Security recommendations

SCALANCE X-200 Operating Instructions, 03/2015, C79000-G8976-C284-06

Keys and certificates

This section deals with the security keys and certificates you require to set up SSL.

● We strongly recommend that you create your own SSL certificates and make them

available.

There are preset certificates and keys on the device. The preset and automatically created SSL certificates are self-signed. We recommend that you use SSL certificates signed either by a reliable external or by an internal certification authority. The device has an interface via which you can import the certificates and keys.

● We recommend that you use certificates with a key length of 2048 bits.

Secure/non-secure protocols

● Check whether use of SNMPv1 is necessary. SNMPv1 is classified as non-secure. Use

the option of preventing write access. The product provides you with suitable setting options.

● For the DCP function, enable the "DCP read-only" mode after commissioning.

● If SNMP is enabled, change the community names. If no unrestricted access is

necessary, restrict access with SNMP.

● Use secure protocols when access to the device is not prevented by physical protection

measures.

The following protocols provide secure alternatives:

– SNMPv1 → SNMPv3

– HTTP → HTTPS

– Telnet → SSH

– SNTP → NTP (secure)

● Avoid or disable non-secure protocols, for example Telnet and TFTP. For historical

reasons, these protocols are still available, however not intended for secure applications. Use non-secure protocols with caution.

● To prevent unauthorized access to the device or network, take suitable protective

measures against non-secure protocols.

Available protocols per port

The following list provides you with an overview of the open ports on this device. Keep this in mind when configuring a firewall.

The table includes the following columns:

●

Protocol

All protocols that the device supports

●

Port number

Port number assigned to the protocol

Safety notices

3.3 Security recommendations

SCALANCE X-200

32 Operating Instructions, 03/2015, C79000-G8976-C284-06

●

Port status

– Open

The port is always open and cannot be closed.

– Open (when configured)

The port is open if it has been configured.

Note

With some protocols the port may be open although the corresponding protocol is disabled, for example TFTP.

●

Default status of the port

– Open

As default the port is open.

– Closed

As default the port is closed.

●

Authentication

Specifies whether or not the protocol is authenticated during access.

Protocol

Port number

Port status

Default status of the port

Authentication SSH

TCP/22 Open Open Yes

HTTP

TCP/80

Open

Yes

HTTPS

TCP/443

Open

Yes

SNTP NTP (secure)

UDP/123 Open

(when configured)

Closed No

SNMP

UDP/161 Open

(when configured)

Open Yes

PROFINET IO

UDP/34964

UDP/1026, 1027

Open Open No

PROFINET IO Service

TCP/84 Open Open No

SCALANCE X-200 Operating Instructions, 03/2015, C79000-G8976-C284-06

4.1

Safety notices for installation

Safety notices

When installing the device, keep to the notices listed below.

WARNING

When used in ships, a DIN rail does provide adequate support

For the following devices, installation on a 35 mm DIN rail for use in ships is not permitted:

• X201-3P IRT PRO

• X202-2P IRT PRO

• X204IRT PRO

• X208PRO

• X212-2

• X212-2LD

• X216

• X224

In ships, the DIN rail does not provide adequate support.

WARNING

If a device is operated in an ambient temperature of more than 50 °C, the temperature of the device housing may be higher than 70 °C. The device must therefore be installed so that it is only accessible to service personnel or users that are aware of the reason for restricted access and the required safety measures at an ambient temperature higher than 50 °C.

WARNING

If the cable or conduit entry point exceeds 70 °C or the branching point of conductors exceeds 80 °C, special precautions must be taken. If the equipment is operated in an air ambient in excess of 50 °C, only use cables with admitted maximum operating temperature of at least 80 °C.

Installation

4.1 Safety notices for installation

SCALANCE X-200

34 Operating Instructions, 03/2015, C79000-G8976-C284-06

Safety notices on use in hazardous areas

General safety notices relating to protection against explosion

WARNING

The device may only be operated in an environment with pollution degree 1 or 2 (see IEC 60664-1).

WARNING

When used in hazardous environments corresponding to Class I, Division 2 or Class I, Zone 2, the device must be installed in a cabinet or a suitable enclosure.

WARNING

EXPLOSION HAZARD

SUBSTITUTION OF COMPONENTS MAY IMPAIR SUITABILITY FOR CLASS I, DIVISION 2 OR ZONE 2.

Safety notices for use according to ATEX and IECEx

If you use the device under ATEX or IECEx conditions you must also keep to the following safety notices in addition to the general safety notices for protection against explosion:

WARNING

To comply with EU Directive 94/9 (ATEX95), this enclosure or the cabinet must meet the requirements of at least IP54 in compliance with EN 60529.

Devices with op is approval for optical ports

Some devices have an additional ATEX approval according to II 3 (2) G Ex nA [op is] IIC T4 or an additional IECEx approval according to Ex nA [op is Gb] IIC T4 Gc, refer to the section "Approvals (Page 59). This is indicated on the type plate. With these devices the FO bus connections may run through or in a Zone 1 hazardous area.

Installation

4.1 Safety notices for installation

SCALANCE X-200 Operating Instructions, 03/2015, C79000-G8976-C284-06

Further notes

NOTICE

Warming and premature aging of the IE switch due to direct sunlight

Direct sunlight can heat up the device and can lead to premature aging of the IE switch and its cabling.

Provide suitable shade to protect the IE switch against direct sunlight.

Note Note the mounting position for XF and TS devices

With the following IE switches, an ambient temperature of maximum +40 °C is permitted if the device is installed on a vertical rail:

•

X204-2TS

•

X204-2LD TS

•

XF204

•

XF204-2

•

XF206-1

•

XF208

•

XF204IRT

Installation

4.2 Installation options

SCALANCE X-200

36 Operating Instructions, 03/2015, C79000-G8976-C284-06

4.2

Installation options

Types of installation

IE Switches X-200 can be installed in the following ways:

● Installation on a 35 mm DIN rail complying with DIN EN 60715

● Installation on a SIMATIC S7-300 standard rail

● Wall mounting

Unless stated otherwise, the mounting options listed below apply to all X-200 IE switches.

Exception XF-200

The XF devices (flat design) can only be installed on a 35 mm DIN rail.

Installation

4.3 Installation on a DIN rail

SCALANCE X-200 Operating Instructions, 03/2015, C79000-G8976-C284-06

4.3

Installation on a DIN rail

Installation

Figure 4-1 Installation on a 35 mm DIN rail

To install an X-200 on a 35 mm DIN rail complying with DIN EN 60715, follow the steps below:

1. Place the upper catch of the device over the top of the DIN rail and then push in the lower

part of the device against the rail until it clips into place.

2. Fit the connectors for the power supply.

3. Fit the connectors for the signaling contact

4. Insert the terminal blocks or M12 cable connectors into the sockets on the device.

Removal

Figure 4-2 Removing from a 35 mm DIN rail

To remove an X-200 from a DIN rail, follow the steps below:

1. First disconnect all connected cables.

2. Use a screwdriver to release the lower DIN rail catch of the device and pull the lower part

of the device away from the rail.

Installation

4.4 Installation on a standard rail

SCALANCE X-200

38 Operating Instructions, 03/2015, C79000-G8976-C284-06

4.4

Installation on a standard rail

Installation on a SIMATIC S7-300 standard rail

To install an X-200 on a standard rail, follow the steps below:

1. Fit the housing guide on the top of the housing into the standard rail.

2. Screw the X-200 to the underside of the standard rail.

3. Fit the connectors for the power supply.

4. Fit the connectors for the signaling contact.

5. Insert the terminal blocks or M12 cable connectors into the sockets on the X-200.

Figure 4-3 Installation on a SIMATIC S7-300 standard rail

Removal

To remove an X-200 from a standard rail, follow the steps below:

1. First disconnect all connected cables.

2. Release the screws on the bottom of the standard rail.

3. Then lift the X-200 away from the standard rail.

Installation

4.5 Wall mounting

SCALANCE X-200 Operating Instructions, 03/2015, C79000-G8976-C284-06

4.5

Wall mounting

Note

The wall mounting must be capable of supporting at least four times the weight of the X-200, see section

Technical specifications (Page 67).

When mounting on a wall, use mounting fittings suitable for the type of wall. To secure the device in concrete, you could, for example use the following material:

● 4 wall plugs, 6 mm in diameter and 30 mm long

● 4 screws 3.5 mm in diameter and 40 mm long

Follow the steps below to install the X-200 on a wall:

1. Prepare the drill holes for wall mounting.

You will find the precise dimensions in the Appendix Dimension drawings (Page 77).

2. Connect the electrical cable connecting cables.

3. Fit the connectors for the signaling contact.

4. Insert the terminal blocks or M12 cable connectors into the sockets on the IE Switch X-

200.

5. Screw the device to the wall.

Installation

4.5 Wall mounting

SCALANCE X-200

40 Operating Instructions, 03/2015, C79000-G8976-C284-06

SCALANCE X-200 Operating Instructions, 03/2015, C79000-G8976-C284-06

5.1

Safety when connecting up

Safety notices

When connecting up the device, keep to the safety notices listed below.

WARNING

The equipment is designed for operation with Safety Extra-Low Voltage (SELV) by a Limited Power Source (LPS).

This means that only SELV / LPS complying with IEC 60950-1 / EN 60950-1 / VDE 0805-1 must be connected to the power supply terminals. The power supply unit for the equipment power supply must comply with NEC Class 2, as described by the National Electrical Code (r) (ANSI / NFPA 70).

If the equipment is connected to a redundant power supply (two separate power supplies), both must meet these requirements.

Safety notices on use in hazardous areas

General safety notices relating to protection against explosion

WARNING

EXPLOSION HAZARD

DO NOT CONNECT OR DISCONNECT EQUIPMENT WHEN A FLAMMABLE OR COMBUSTIBLE ATMOSPHERE IS PRESENT.

Exceptions

For the devices listed below, there are no requirements according to NEC Class 2 or LPS. For these devices, note the conditions described in the section Supply for IRT-PRO devices (Page 45).

● X201-3P IRT PRO

● X202-2P IRT PRO

● X204IRT PRO

Connecting up

5.1 Safety when connecting up

SCALANCE X-200

42 Operating Instructions, 03/2015, C79000-G8976-C284-06

Safety notices when using the device according to Hazardous Locations (HazLoc)

If you use the device under HazLoc conditions you must also keep to the following safety notices in addition to the general safety notices for protection against explosion:

WARNING

EXPLOSION HAZARD

DO NOT DISCONNECT WHILE CIRCUIT IS LIVE UNLESS AREA IS KNOWN TO BE NON-HAZARDOUS.

Safety notices for use according to ATEX and IECEx

If you use the device under ATEX or IECEx conditions you must also keep to the following safety notices in addition to the general safety notices for protection against explosion:

WARNING

Take measures to prevent transient voltage surges of more than 40% of the rated voltage. This is the case if you only operate devices with SELV (safety extra-low voltage).

Connecting up

5.1 Safety when connecting up

SCALANCE X-200 Operating Instructions, 03/2015, C79000-G8976-C284-06

Further notes

WARNING

CAUTION

Electric shock - turn off the power supply

Turn off the power supply before you connect or disconnect cables from the device.

NOTICE

Overvoltage protection

If IE Switches X-200 are supplied over long 24 V power supply lines or networks, measures are necessary to prevent interference by strong electromagnetic pulses on the supply lines. These can result, for example, due to lightning or switching of large inductive loads.

One of the tests used to attest the immunity of devices of the IE Switches X-200 to electromagnetic interference was the "surge immunity test" according to EN61000-4-5. This test requires overvoltage protection for the power supply lines. A suitable device is, for example, the Dehn Blitzductor BVT AVD 24 V type no. 918 422 or a comparable protective element.

Manufacturer: DEHN+SÖHNE GmbH+Co.KG, Hans-Dehn-Str.1, Postfach 1640, D-92306 Neumarkt, Germany.

Connecting up

5.2 Power supply

SCALANCE X-200

44 Operating Instructions, 03/2015, C79000-G8976-C284-06

5.2

Power supply

5.2.1

Power supply via terminal block

Power supply

The power supply is connected via a 4-pin plug-in terminal block that ships with the device.

● The power supply can be connected redundantly.

– Both inputs are isolated.

– No load distribution.

– The power supply unit with the higher output voltage supplies the device alone.

● Power: 24 VDC

● Cable cross section for X-200: 2.5 mm

● Cable cross section for XF-200: 1.5 mm

● The power supply is connected over a high resistance with the enclosure to allow an ungrounded set up.

● The power supply is non-floating.

● The signal cables of the electrical Ethernet interfaces are floating.

The following table shows the pin assignment:

Pin no.:

Assignment

1 L1: 24 VDC

With TS devices: L1: 12 to 24 VDC

2 M1

4 L2: 24 VDC

With TS devices: L2: 12 to 24 VDC

Note Special features with X208PRO and the IRT-PRO devices

Note the special requirements for the power supply for the devices in the following sections.

Connecting up

5.2 Power supply

SCALANCE X-200 Operating Instructions, 03/2015, C79000-G8976-C284-06

5.2.2

Supply for X208PRO

Power supply for X208PRO

With the IE switch SCALANCE X208PRO, the power supply is connected via two 4-pin acoded M12 sockets.

● The power supply can be connected redundantly.

– Both inputs are isolated.

– No load distribution.

– The power supply unit with the higher output voltage supplies the device alone.

● Power: 24 VDC

● The power supply is connected over a high resistance with the enclosure to allow an

ungrounded set up.

● The power supply is non-floating.

● The signal cables of the electrical Ethernet interfaces are floating.

The following table shows the pin assignment:

Pin no.:

Assignment

L1 or L2: 24 VDC

2 n. c.

M1 or M2

4 n. c.

5.2.3

Supply for IRT-PRO devices

Power supply for the devices of the IRT PRO version

The following descriptions of the power supply apply to the following devices:

● X201-3P IRT PRO

● X202-2P IRT PRO

● X204IRT PRO

The power supply is connected via the push-pull Power Plug PRO. This plug has a high degree of protection (IP65/IP67) and is suitable for use outside cabinets and complies with PROFINET connector technology.

The Power Plug PRO does not ship with the device and can be ordered under the following order number: 6GK1907-0AB10-6AA0

Connecting up

5.2 Power supply

SCALANCE X-200

46 Operating Instructions, 03/2015, C79000-G8976-C284-06

Power supply

● Power: 24 VDC

● The power supply is connected over a high resistance with the enclosure to allow an

ungrounded set up.

● The power supply is non-floating.

● The signal cables of the electrical Ethernet interfaces are floating.

Note No redundant power supply

Since the IRT PRO version of the devices does not have a redundant power supply, connect the power supply to L1 and N1.

Note Plug in metal casing

•

If the devices are operated at an ambient temperature in excess of 40 °C or if currents

higher than 6 A flow via the connector, the connector with the metal casing must be used.

•

In areas subject to the National Electric Code (NEC), the Canadian Electric Code (CEC)

and the EC directive 94/9 (ATEX) and IECEx, metal connectors must be used.

Note Maximum current 16 A

The current through the Power Plug PRO must not exceed 16 A. You should therefore include a fuse that trips at a current higher than 16 A.

In areas subject to the NEC or CEC, the fuse must meet the following requirements:

•

Suitable for DC (min. 60 V / max. 16 A)

•

Breaking current at least 10 kA

•

UL / CSA listed (UL 248-1 / CSA 22.2 No. 248.1)

•

Classes R, J, L, T or CC.

Otherwise the following requirements must be met:

•

Suitable for DC (min. 60 V / max. 16 A)

•

Breaking current at least 10 kA

•

Approved according to IEC/EN 60127-1

•

Breaking characteristics

– With circuit breakers: B or C

– With fuses: slow blow

Connecting up

5.2 Power supply

SCALANCE X-200 Operating Instructions, 03/2015, C79000-G8976-C284-06

Power supply looped through

The devices also have a connector for the switched mode and unswitched power supply of other devices with 24 VDC. Via these interfaces (L1+, N1 and L2+, N2) it is possible to loop the power through with connector technology compliant with PROFINET.

Note Notes on operating under marginal conditions

When looping through the power supply, take into account the limit values; in other words, the maximum permitted current depending on the ambient temperature; refer to the table "Operation under marginal conditions" below.

When looping through the power su

pply under the marginal conditions described below, the

device may only be operated if it is installed horizontally. Horizontal installation position means that the device is mounted, for example on a horizontal DIN or standard rail or that the labeling on

the device can be read in the normal reading direction.

If no power is looped through, any installation position is permitted.

Table 5- 1 Operation under marginal conditions

Environment

Max Power 1 (L1+, N1)

Max Power 2 (L2+, N2)

+40℃

16 A

+50℃

12 A

+60℃

8 A

SCALANCE X204IRT PRO only:

+70°C

6 A

Pin assignment of the connectors

The following table shows the pin assignment of the two power supply connectors:

Pin no.:

Assignment

L1: 24 VDC

L2: 24 VDC

5 FE (Functional Earth)

Connecting up

5.3 Grounding

SCALANCE X-200

48 Operating Instructions, 03/2015, C79000-G8976-C284-06

5.3

Grounding

Grounding when installing on a DIN rail

The device is grounded over the DIN rail.

Grounding when installing on an S7 standard rail

The device is grounded over its rear panel and the neck of the screw.

Grounding with wall mounting

The device is grounded by the securing screw in the unpainted hole.

Please note that X-200 IE switches must be grounded over one securing screw with minimum resistance.

If an IE Switch X-200 is mounted on a non-conducting base, a grounding cable must be installed. The grounding cable is not supplied with the device. Connect the paint-free surface of the device to the nearest grounding point using the grounding cable.

Connecting up

5.4 Signaling contact

SCALANCE X-200 Operating Instructions, 03/2015, C79000-G8976-C284-06

5.4

Signaling contact

The signaling contact or relay contact is a floating switch with which error/fault states can be signaled by breaking the contact.

The following errors/faults can be signaled by the signaling contact:

● The loss and the establishment of a link on a monitored port.

● The failure of one of the two redundant power supplies.

Note: Devices of the IRT PRO version do not have a redundant power supply

● The loss of the connection to the controller in PROFINET IO mode.

● The redundancy manager signals an error

● An incompatible C-PLUG was inserted.

The connection or disconnection of a communication node on an unmonitored port does not lead to an error message.

The signaling contact remains activated until the error/fault is eliminated or until the current status is applied as the new desired status using the SET button.

When the IE Switch X-200 is turned off, the signaling contact is always activated, i.e. opened.

NOTICE

Load on the signaling contact

The signaling contact can be subjected to a

maximum

load of

100 mA

(safety extra-low

voltage (SELV), 24 VDC).

Connection via 2-pin terminal block

The signaling contact is connected to a 2-pin plug-in terminal block.

The following table shows the pin assignment:

no.:

Assignment

2 F2

Connecting up

5.4 Signaling contact

SCALANCE X-200

50 Operating Instructions, 03/2015, C79000-G8976-C284-06

Connection via M12 socket

With the X-200 IRT PRO devices and with the X208PRO, the connection is via a 5-pin, bcoded M12 socket.

The following table shows the pin assignment:

no.:

Assignment

2 n.c.

n.c. 4 F2

5 n.c.

Connecting up

5.5 Attachment to Industrial Ethernet

SCALANCE X-200 Operating Instructions, 03/2015, C79000-G8976-C284-06

5.5

Attachment to Industrial Ethernet

Note Redundancy mechanisms

If you use redundancy mechanisms such as media redundancy "HRP" or "MRP" and/or redundant linking of rings via a standby link, remember the following:

Open the redundant path before you insert a new device or replacement device in an operating network. A

bad configuration or attachment of the Ethernet cables to incorrectly

configured ports causes overload in the network and a breakdown in communication.

A device may only be inserted in a network and connected in the following situations:

•

HRP / MRP

– The ring ports of the device being inserted in the ring were configured as ring ports. – The required redundancy mode is also enabled. – If the device is intended to operate as the redundancy manager, "Enable Ring

Redundancy" must also be set.

•

Standby link

– Select "Enable Standby Master". – The "Standby Connection Name" must match the name of the partner device. – You must also configure the standby port.

You will find detailed information in the SCALANCE X

-200 configuration manual.

5.5.1

Electrical connections

5.5.1.1

Electrical attachments to Industrial Ethernet

Connection via RJ-45 jacks

The electrical connectors for Industrial Ethernet on the X-200 IE switch are designed as RJ45 jacks with the following properties:

● MDI-X assignment

● Autonegotiation

● Auto polarity exchange

Connecting up

5.5 Attachment to Industrial Ethernet

SCALANCE X-200

52 Operating Instructions, 03/2015, C79000-G8976-C284-06

MDI / MDI-X autocrossover function

The advantage of this function is that straight-through cables can be used throughout and external Ethernet crossover cables are unnecessary. This prevents malfunctions resulting from mismatching send and receive wires. This makes installation much easier for the user.

Note Formation of loops

Please not

e that the direct connection of two ports on the switch or accidental connection

over several switches causes an illegal loop. Such a loop can lead to network overload and network failures.

Autonegotiation

Autonegotiation means the automatic detection of the functionality of the port at the opposite end. Using autonegotiation, repeaters or end devices can detect the functionality available at the port of a partner device allowing automatic configuration of different types of device. With autonegotiation, two components connected to a link segment can exchange parameters and set themselves to match the supported communication functionality.

Note

•

If a port operating in autonegotiation mode is connected to a partner device that is not

operating in autonegotiation mode, the partner device must be set permanently to half duplex mode.

•

If a port is set permanently to full duplex, the connected partner device must also be set

to full duplex.

•

If the autonegotiation function is disabled, the MDI/MDI-X autocrossover function is also

inactive. This means it may be necessary to use a crossover cable.

Auto polarity exchange

If the pair of receiving cables is incorrectly connected, in other words, RD+ and RD- are swapped over, the polarity is reversed automatically.

Connecting up

5.5 Attachment to Industrial Ethernet

SCALANCE X-200 Operating Instructions, 03/2015, C79000-G8976-C284-06

PIN assignment

The following table shows the pin assignment of the RJ-45 connectors:

Pin no.:

Assignment

n. c.

7 n. c.

TD- 5 n. c. 4 n. c. 3 TD 2 RD-

1 RD+

Permitted cable lengths

● With connection using TP cords or TP-XP cords: maximum 10 m

● When connected using IE FC cable with IE RJ-45 plug:

Depending on the cable type, a total length of up to 100 m is permitted between two devices.

5.5.1.2

Electrical connectors of the X208PRO

Connection via M12 sockets

With the IE switch SCALANCE X208PRO, the connection to Industrial Ethernet is via 4-pin, d-coded M12 sockets with MDI-X assignment.

MDI / MDI-X autocrossover function

Note Formation of loops

Please note that the direct connection of two ports on the switch or accidental connection over several switches causes an illegal loop. Such a loop can lead to network overload and network failures.

Connecting up

5.5 Attachment to Industrial Ethernet

SCALANCE X-200

54 Operating Instructions, 03/2015, C79000-G8976-C284-06

PIN assignment

The following table shows the pin assignment of the M12 sockets:

Pin no.:

Assignment

RX+

2 TX+

RX- 4 TX-

Permitted cable lengths

● With connection using TP cords or TP-XP cords: maximum 10 m

● When connected using IE FC cable with IE RJ-45 plug:

Depending on the cable type, a total length of up to 100 m is permitted between two devices.

IE FC M12 plug PRO

The IE FC M12 Plug PRO has a high degree of protection (IP65/67) and is suitable for connecting the X208PRO to Industrial Ethernet. You can obtain this plug using the following order number: 6GK1 901-0DB20-6AA0.

Connecting up

5.5 Attachment to Industrial Ethernet

SCALANCE X-200 Operating Instructions, 03/2015, C79000-G8976-C284-06

5.5.2

Optical attachments to Industrial Ethernet

5.5.2.1

Multimode fiber-optic cable

Transmission medium

The following X-200 IE switches use multimode fiber-optic cables as the transmission medium:

● X204-2

● X204-2TS

● X204-2FM

● X206-1

● X212-2

● XF204-2

● XF206-1

● X202-2IRT

Characteristics:

Transmission speed

100 Mbps

Transmission mode

100Base-FX according to IEEE 802.3

Connectors BFOC sockets

Wavelength

1310 nm

Core diameter

50 or 62.5 μm

Outer diameter

125 μm

Light source

LED

Maximum range (segment length)

5 km

Note No autonegotiation

With optical transmission, the full duplex mode and transmission

speed cannot be changed.

For this reason, the autonegotiation function cannot be selected.

Connecting up

5.5 Attachment to Industrial Ethernet

SCALANCE X-200

56 Operating Instructions, 03/2015, C79000-G8976-C284-06

5.5.2.2

Single mode fiber-optic cable

Transmission medium

The following X-200 IE switches use single mode fiber-optic cables as the transmission medium:

● X204-2LD

● X204-2LD TS

● X206-1LD

● X212-2LD

Characteristics:

Transmission speed

100 Mbps

Transmission mode

100Base-FX according to IEEE 802.3

Connectors BFOC sockets

Wavelength

1310 nm

Core diameter 9 μm

Outer diameter

125 μm

Light source

LED

Maximum range (segment length)

26 km

Note No autonegotiation

With optical transmission, the full duplex mode and transmission speed cannot be changed. For this reason, the autonegotiation function cannot be selected.

5.5.2.3

POF and PCF cables

Transmission medium

The following X-200 IE switches use Plastic Optical Fiber (POF) or Polymer Cladded Fiber (PCF) as the transmission medium:

● X200-4P IRT

● X201-3P IRT

● X201-3P IRT PRO

● X202-2P IRT

● X202-2P IRT PRO

Connecting up

5.5 Attachment to Industrial Ethernet

SCALANCE X-200 Operating Instructions, 03/2015, C79000-G8976-C284-06

Characteristics:

Transmission speed 100 Mbps

Transmission mode

100Base-FX analogous to IEEE 802.3

Connectors SC RJ jacks

Wavelength

650 nm

Core diameter

• with POF

• with PCF

• 980 μm

• 200 μm

Outer diameter

• with POF

• with PCF

• 1000 μm

• 230 μm

Light source

LED

Cable lengths

• minimum

• maximum segment length

• 0 m

• 50 m for POF

100 m for PCF

Signal attenuation

• with POF

• with PCF

• 0.230 dB/m

• 0.01 dB/m

Note No autonegotiation

With optical transmission, the full duplex mode and transmission speed cannot be changed. For this reason, the autonegotiation function cannot be selected.

GI-PCF

For segment lengths longer than 100 m, you can use GI-PCF cables. Note the information of the manufacturer.

Connecting up

5.5 Attachment to Industrial Ethernet

SCALANCE X-200

58 Operating Instructions, 03/2015, C79000-G8976-C284-06

5.5.3

Push-pull connector for IRT-PRO devices

Push-pull connector technology

With the following devices, the connection to Industrial Ethernet makes use of the PROFINET-compliant push-pull connector technology:

● X204IRT PRO

● X202-2P IRT PRO

● X201-3P IRT PRO

Due to their high degree of protection (IP65/IP67), the push-pull connectors are suitable for installation outside cabinets. The plugs do not ship with the product. You will find ordering data below.

IE FC RJ-45 Plug PRO or IE RJ-45 Plug PRO

For the electrical attachment, use one of the following connectors:

● IE FC RJ-45 Plug PRO

Order no.: 6GK1 901-1BB20-6AA0

● IE RJ-45 Plug PRO

Order no.: 6GK1 901-1BB10-6AA0

IE SC RJ POF Plug PRO and IE SC RJ PCF Plug PRO

For the optical attachment, use one of the following connectors:

● IE SC RJ

POF

Plug PRO

Order no.: 6GK1 900-0MB00-6AA0

● IE SC RJ

PCF

Plug PRO

Order no.: 6GK1 900-0NB00-6AA0

SCALANCE X-200 Operating Instructions, 03/2015, C79000-G8976-C284-06

Approvals issued

Note Issued approvals on the type plate of the device

The specified approvals apply only when the corresponding mark is printed on the product. You can check which of the following approvals have been granted for your product by the markings on the type plate.

Approvals for shipbuilding are not printed on the device type plate.

Current approvals on the Internet

You will also find the current approvals for the product on the Internet pages of Siemens Industry Online Support under the following entry ID:

33118791 (http://support.automation.siemens.com/WW/view/en/33118791

)

→ "Entry list" tab, entry type "Certificates"

Approvals for SIMATIC NET products

You will find an overview of the approvals for SIMATIC NET products including approvals for shipbuilding on the Internet pages of Siemens Industry Online Support under the following entry ID:

57337426 (http://support.automation.siemens.com/WW/view/en/57337426

)

EC directives

SIMATIC NET products meet the requirements and aims of the following EC directives.

EMC directive (electromagnetic compatibility)

The SIMATIC NET products described in these operating instructions meet the requirements of EC directive 2004/108/EC "Electromagnetic Compatibility" for the following areas of application:

Field of application

Requirements

Emission

Immunity to interference

Industry

EN 61000-6-4 : 2007

EN 61000-6-2 : 2005

Approvals

SCALANCE X-200

60 Operating Instructions, 03/2015, C79000-G8976-C284-06

EU declaration of conformity

You will find EC declaration of conformity for these products on the Internet pages of Siemens Industry Online Support (http://support.automation.siemens.com/WW/view/en/33118389/134200

Explosion protection directive (ATEX)

The product meets the requirements of the EC directive 94/9/EC "Equipment and Protective Devices for Use in Potentially Explosive Atmospheres".

The current versions of the standards can be seen in the EU Declaration of Conformity.

II 3 G Ex nA IICT4 Gc

The IE switches SCALANCE X-200 meet the requirements according to II 3 G Ex nA IIC T4 Gc, certificate no.: KEMA 07ATEX0145 X:

• X204-2

• X204-2TS

• X204-2FM

• X204-2LD

• X204-2LD TS

• X206-1

• X206-1LD

• X208

• X208PRO

• X212-2

• X212-2LD

• X216

• X224

• XF204

• XF204-2

• XF206-1

• XF208

• X200-4P IRT

• X201-3P IRT

• X201-3P IRT PRO

• X202-2IRT

• X202-2P IRT

• X202-2P IRT PRO

• X204IRT

• X204IRT PRO

• XF204IRT

These products meet the requirements of the following standards:

● EN 60079-15

● EN 60079-0

Approvals

SCALANCE X-200 Operating Instructions, 03/2015, C79000-G8976-C284-06

II 3 (2) G Ex nA [op is] IIC T4

The IE switches SCALANCE X-200 listed below have additional approval according to II 3 (2) G Ex nA [op is] IIC T4, certificate no.: DEKRA11ATEX0060 X:

• X204-2

• X204-2TS

• X204-2FM

• X206-1

• X212-2

• XF204-2

• XF206-1

• X202-2IRT

These products meet the requirements of the following standards:

● EN 60079-0

● EN 60079-15

● EN 60079-28

See also

16689636 (http://support.automation.siemens.com/WW/view/en/16689636)

IECEx

The SIMATIC NET products meet the requirements of explosion protection according to IECEx.

IECEx classification:

Ex nA IIC T4 Gc

DEK 14.0025X

The products meet the requirements of the following standards:

● IEC 60079-15 (Explosive atmospheres - Part 15: Equipment protection by type of

protection "n")

● IEC 60079-0 (Explosive atmospheres - Part 0: Equipment - General requirements)

The current versions of the standards can be seen in the EU Declaration of Conformity.

Approvals

SCALANCE X-200

62 Operating Instructions, 03/2015, C79000-G8976-C284-06

The following SCALANCE X-200 IE switches meet these requirements:

• X204-2

• X204-2TS

• X204-2FM

• X204-2LD

• X204-2LD TS

• X206-1

• X206-1LD

• X208

• X208PRO

• X212-2

• X212-2LD

• X216

• X224

• XF204

• XF204-2

• XF206-1

• XF208

• X200-4P IRT

• X201-3P IRT

• X201-3P IRT PRO

• X202-2IRT

• X202-2P IRT

• X202-2P IRT PRO

• X204IRT

• X204IRT PRO

• XF204IRT

IECEx (optical radiation)

The SIMATIC NET products meet the requirements of explosion protection according to IECEx.

IECEx classification:

Ex nA [op is Gb] IIC T4 Gc

DEK 14.0026X

The products meet the requirements of the following standards:

● IEC 60079-15 (Explosive atmospheres - Part 15: Equipment protection by type of protection "n"

● IEC 60079-0 (Explosive atmospheres - Part 0: Equipment - General requirements)

● IEC 60079-28 (Explosive atmospheres - Part 28: Protection of equipment and

transmission systems using with optical radiation)

The following SCALANCE X-200 IE switches also meet these requirements:

• X204-2

• X204-2TS

• X204-2FM

• X206-1

• X212-2

• XF204-2

• XF206-1

• X202-2IRT

Approvals

SCALANCE X-200 Operating Instructions, 03/2015, C79000-G8976-C284-06

The product meets the requirements of the standards:

● Factory Mutual Approval Standard Class Number 3611

● FM Hazardous (Classified) Location Electrical Equipment:

Non Incendive / Class I / Division 2 / Groups A,B,C,D / T4 and Non Incendive / Class I / Zone 2 / Group IIC / T4

cULus approval for industrial control equipment

cULus Listed IND. CONT. EQ.

Underwriters Laboratories Inc. complying with

● UL 508

● CSA C22.2 No. 142-M1987

Report no. E85972

cULus Approval for Information Technology Equipment

cULus Listed I. T. E.

Underwriters Laboratories Inc. complying with

● UL 60950-1 (Information Technology Equipment)

● CSA C22.2 No. 60950-1-03

Report no. E115352

cULus Approval Hazardous Location

cULus Listed I. T. E. FOR HAZ. LOC.

Underwriters Laboratories Inc. complying with

● UL 60950-1 (Information Technology Equipment)

● ANSI/ISA 12.12.01-2007

● CSA C22.2 No. 213-M1987

Approved for use in Cl. 1, Div. 2, GP A, B, C, D T4 Cl. 1, Zone 2, GP IIC T4

Report no. E240480

CSA Approval for Information Technology Equipment

CSA Certification Mark

Canadian Standard Association CSA C22.2 No. 60950-1-03

Approvals

SCALANCE X-200

64 Operating Instructions, 03/2015, C79000-G8976-C284-06

CSA Approval for Industrial Control Equipment

CSA Certification Mark

Canadian Standard Association CSA C22.2 No. 142-1987

FDA and IEC approvals

The following SCALANCE X-200 switches meet the FDA and IEC requirements listed below:

● X204-2LD

● X204-2LD TS

● X206-1LD

● X212-2LD

Figure 6-1 FDA and IEC approvals

CAUTION

Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure.

RCM

The product meets the requirements of the AS/NZS 2064 standard (Class A).

KC (Korean Standard)

The products meet the requirements of the "Korean Standard".

Marking for the customs union

EAC (Eurasian Conformity)

Customs union of Russia, Belarus and Kazakhstan

Declaration of the conformity according to the technical regulations of the customs union (TR CU)

Approvals

SCALANCE X-200 Operating Instructions, 03/2015, C79000-G8976-C284-06

Railway approval

The TS variant of the device meets the requirements of the Railway standard EN 50155:2007 "Railway Applications - Electronic equipment used on rolling stock".

Approvals

SCALANCE X-200

66 Operating Instructions, 03/2015, C79000-G8976-C284-06

SCALANCE X-200 Operating Instructions, 03/2015, C79000-G8976-C284-06

Construction

Type

Dimensions (W x H x D) in mm

Weight in g

Installation options

- DIN rail

- S7-300 standard rail

- Wall mounting

X204-2

60 x 125 x 124

780 + X204-2TS

60 x 125 x 124

780 + X204-2FM

60 x 125 x 124

780 + X204-2LD

60 x 125 x 124

780 + X204-2LD TS

60 x 125 x 124

780 + X206-1

60 x 125 x 124

780 + X206-1LD

60 x 125 x 124

780

X208

60 x 125 x 124

780 + X208PRO

90 x 125 x 124

1000 + X212-2

120 x 125 x 124

1200 + X212-2LD

120 x 125 x 124

1200 + X216

120 x 125 x 124

1200 + X224

180 x 125 x 124

1600 + XF204

75 x 125 x 73

250

DIN rail mounting only.

XF204-2

75 x 125 x 73

250

DIN rail mounting only.

XF206-1

75 x 125 x 73

250

DIN rail mounting only.

XF208

75 x 125 x 73

250

DIN rail mounting only.

X200-4P IRT

60 x 125 x 124

780 + X201-3P IRT

60 x 125 x 124

780 + X201-3P IRT PRO

90 x 125 x 124

1000 + X202-2IRT

60 x 125 x 124

780 + X202-2P IRT

60 x 125 x 124

780 + X202-2P IRT PRO

90 x 125 x 124

1000

X204IRT

60 x 125 x 124

780 + X204IRT PRO

90 x 125 x 124

1000 + XF204IRT

75 x 125 x 73

250

DIN rail mounting only.

Technical specifications

SCALANCE X-200

68 Operating Instructions, 03/2015, C79000-G8976-C284-06

Ports

Type

Connectors for end devices or network components via twisted pair

RJ-45 jacks with MDI X pinning 10/100 Mbps (half / full duplex) 1)

Connections for end devices or network components via FO cable

BFOC sockets (100 Mbps, full duplex to 100BaseFX)

Connectors for power supply

4-pin plug-in terminal block, redundant 2)

Connectors for signaling contact

2-pin plug-in terminal block 3)

X204-2 4 2 1 1

X204-2TS 4 2 1 1

X204-2FM 4 2 1 1

X204-2LD 4 2 1 1

X204-2LD TS 4 2 1 1

X206-1 6 1 1 1

X206-1LD 6 1 1 1

X208

8 - 1

X208PRO

8 1) - 1 2)

1 3)

X212-2

12 2 1

X212-2LD

12 2 1

X216

16 - 1

X224

24 - 1

XF204

4 - 1 1

XF204-2 4 2 1 1

XF206-1 6 1 1 1

XF208 8 - 1 1

X202-2IRT 2 2 1 1

X204IRT 4 - 1 1

XF204IRT 4 - 1 1

1) Exception X208PRO: Connection via 4-pin, d-coded M12 socket, IP65/67.

2) Exception X208PRO: Connection via 4-pin, a-coded M12 socket, IP65/67.

3) Exception X208PRO: Connection via 5-pin, b-coded M12 socket, IP65/67.

Type

Connectors for end devices or network components via twisted pair

RJ-45 jacks with MDI X pinning 10/100 Mbps (half / full duplex)

Connections for end devices or network components via FO cable

SC RJ jacks (push-pull) (100 Mbps, full duplex to 100BaseFX)

Connector for power supply

4-pin plug-in terminal block, redundant

Connector for signaling contact

2-pin plug-in terminal block

X200-4P IRT - 4 1 1

X201-3P IRT 1 3 1 1

X202-2P IRT 2 2 1 1

Technical specifications

SCALANCE X-200 Operating Instructions, 03/2015, C79000-G8976-C284-06

Type

Connectors for end devices or network components via twisted pair

RJ-45 jacks with MDI X pinning 10/100 Mbps half / full duplex

Connections for end devices or network components via FO cable

SC RJ jacks (push-pull), 100 Mbps, full duplex to 100BaseFX

Connector for power supply

5-pin Power Plug PRO connector (male)

Connector for signaling contact

5-pin b-coded M12 connector (male)

X201-3P IRT PRO

1 3 2

X202-2P IRT PRO

2 2 2

X204IRT PRO 4 - 2 1

Signaling contact

The following applies to all devices:

● Voltage for the signaling contact: 24 VDC

● Current through the signaling contact: maximum 100 mA

Electrical data

Type

Supply voltage with redundant connection

Rated voltage 12 to 24 VDC SELV

Voltage range 10 VDC to

28.8 VDC Permitted voltage range

incl. total ripple 10 VDC to

30.2 VDC

Power loss at 12 VDC

Current consumption at rated voltage

Overcurrent protection at input Non-replaceable fuse (F)

X204-2TS

6.60 W

600 mA

3.0 A / 32 V

X204-2LD TS

6.60 W

600 mA

3.0 A / 32 V

Type

Supply voltage with redundant connection

Rated voltage 24 VDC Voltage range 19.2 VDC

to 28.8 VDC Permitted voltage range

incl. total ripple 18.5 VDC to 30.2 VDC

Power loss at 24 VDC

Current consumption at rated voltage

Overcurrent protection at input PTC resettable fuse

X204-2

6.36 W

265 mA

600 mA / 60 V

X204-2FM

6.36 W

265 mA

600 mA / 60 V

X204-2LD

6.36 W

265 mA

600 mA / 60 V

X206-1

5.28 W

220 mA

600 mA / 60 V

X206-1LD

5.28 W

220 mA

600 mA / 60 V

X208

3.84 W

185 mA

600 mA / 60 V

X208PRO

4.4 W

185 mA

600 mA / 60 V

X212-2

7.92 W

330 mA

1.1 A / 33 V

X212-2LD

7.92 W

330 mA

1.1 A / 33 V

Technical specifications

SCALANCE X-200

70 Operating Instructions, 03/2015, C79000-G8976-C284-06

Type

Supply voltage with redundant connection

Rated voltage 24 VDC Voltage range 19.2 VDC

to 28.8 VDC Permitted voltage range

incl. total ripple 18.5 VDC to 30.2 VDC

Power loss at 24 VDC

Current consumption at rated voltage

Overcurrent protection at input PTC resettable fuse

X216

5.76 W

240 mA

1.1 A / 33 V

X224

8.40 W

350 mA

1.1 A / 33 V

XF204

2.64 W

110 mA

1.1 A / 33 V

XF204-2

5.28 W

220 mA

1.1 A / 33 V

XF206-1

4.08 W

170 mA

1.1 A / 33 V

XF208

3.12 W

130 mA

1.1 A / 33 V

X200-4P IRT

9.6 W

400 mA

1.1 A / 33 V

X201-3P IRT

8.4 W

350 mA

1.1 A / 33 V

X201-3P IRT PRO

no redundancy

7.2 W

300 mA

1.1 A / 33 V

X202-2IRT

6.0 W

300 mA

600 mA / 60 V

X202-2P IRT

+ 7.2 W 300 mA 1.1 A / 33 V

X202-2P IRT PRO

no redundancy

7.2 W

300 mA

1.1 A / 33 V

X204IRT

4.8 W

200 mA

600 mA / 60 V

X204IRT PRO

no redundancy

4.8 W

200 mA

600 mA / 60 V

XF204IRT

+ 4.8 W 200 mA 600 mA / 60 V

Optical data

Type

Transmitter output (optical)

Receiver input

min. [dBm]

max. [dBm]

Sensitivity min. [dBm]

Input power max. [dBm]

X204-2 X204-2TS X204-2FM X206-1 X212-2 XF204-2 XF206-1 X202-2IRT

-19 -14 -32 -3

X204-2LD X204-2LD TS X206-1LD X212-2LD

-15 -8 -34 -3

X200-4P IRT X201-3P IRT X201-3P IRT PRO X202-2P IRT X202-2P IRT PRO

-8 -2 -23 +1

Technical specifications

SCALANCE X-200 Operating Instructions, 03/2015, C79000-G8976-C284-06

Permitted cable lengths - copper

For devices with degree of protection IP20/30

The following cables are permitted in the specified lengths:

●

0 to 55 m:

IE TP torsion cable with IE FC RJ-45 Plug 180

– Alternative:

0 to 45 m IE TP Torsion Cable + 10 m TP Cord via IE Outlet RJ-45

●

0 to 85 m:

IE FC TP marine / trailing / flexible / FRNC / festoon / food cable with IE FC RJ-45 Plug 180

– Alternative:

0 to 75 m IE FC TP marine / trailing / flexible / FRNC / festoon / food cable + 10 m TP cord over IE FC outlet RJ-45

●

0 to 100 m:

IE FC TP standard cable with IE FC RJ-45 plug 180

– Alternative:

0 to 90 m IE FC TP standard cable + 10 m TP cord via IE FC outlet RJ-45

For devices with the "PRO" supplement (degree of protection IP65/67)

With these devices, splitting of the cables (as above) is not permitted. The following cables are permitted in the specified lengths:

●

0 to 55 m:

IE TP torsion cable with IE FC RJ-45 Plug 180

●

0 to 85 m:

IE FC TP marine / trailing / flexible / FRNC / festoon / food cable with IE FC RJ-45 Plug 180

●

0 to 100 m:

IE FC TP standard cable with IE FC RJ-45 plug 180

Technical specifications

SCALANCE X-200

72 Operating Instructions, 03/2015, C79000-G8976-C284-06

For X208PRO (degree of protection IP65/67)

With the X208PRO, splitting of the cables (as above) is not permitted either. The following cables are permitted in the specified lengths:

●

0 to 55 m:

IE TP torsion cable with IE FC M12 Plug PRO

●

0 to 85 m:

IE FC TP marine / trailing / flexible / FRNC / festoon / food cable with IE FC M12 Plug PRO

●

0 to 100 m:

IE FC TP standard cable with IE FC M12 plug PRO

Permitted cable lengths - fiber-optic

Type

1 - 50 m 980/1000 plastic optical fiber (POF)

1 - 100 m 200/230 polymer cladded fiber (PCF)

6 dB max. permitted cable attenuation with 3 dB link power margin

0 - 4000 Glass FO cable

62.5/125 µm glass fibers 0 - 5000

Glass FO cable 50/125 µm glass fibers

≤ 1 dB/km at 1300 nm; 600 MHz x km; 6 dB max. permitted cable

attenuation with 3 dB link power margin

0 - 26000 m glass FO cable

9/125 µm single mode fiber;

0.5 dB/km at 1300 nm; 13 dB max. permitted

cable attenuation with 2 dB link power margin

X204-2 - - + -

X204-2TS - - + -

X204-2FM - - + -

X204-2LD - - - +

X204-2LD TS - - - +

X206-1 - - + -

X206-1LD - - - +

X212-2 - - + -

X212-2LD - - - +

XF204-2 - - + -

XF206-1

- - + -

X200-4P IRT + + - -

X201-3P IRT + + - -

X201-3P IRT PRO

+ + -

X202-2IRT

- - + -

X202-2P IRT + + - -

X202-2P IRT PRO

+ + -

Technical specifications

SCALANCE X-200 Operating Instructions, 03/2015, C79000-G8976-C284-06

Degree of protection and MTBF

Type

Degree of protection

MTBF

X204-2

IP30

64 years

X204-2TS

IP20

63 years

X204-2FM

IP30

87 years

X204-2LD

IP30

60 years

X204-2LD TS

IP20

85 years

X206-1

IP30

72 years

X206-1LD

IP30

69 years

X208

IP30

83 years

X208PRO

IP65/67

83 years

X212-2

IP30

46 years

X212-2LD

IP30

43 years

X216

IP30

52 years

X224

IP30

45 years

XF204

IP20

48 years

XF204-2

IP20

60 years

XF206-1

IP20

69 years

XF208

IP20

54 years

X200-4P IRT

IP30

73 years

X201-3P IRT

IP30

78 years

X201-3P IRT PRO

IP67 85 years

X202-2IRT

IP30

62 years

X202-2P IRT

IP30

84 years

X202-2P IRT PRO

IP67

85 years

X204IRT

IP30

81 years

X204IRT PRO

IP67

99 years

XF204IRT

IP20

81 years

Switching properties

Type

Max. number of learnable addresses

Aging time

Switching technique

Latency X-200

8000

30 s

Store and forward

5 μs

XF-200

8000

30 s

Store and forward

5 μs

X-200IRT

4096

30 s (configurable)

Store and forward / cut through

< 5 μs

XF204IRT

4096

30 s (configurable)

Store and forward / cut through

< 5 μs

Technical specifications

SCALANCE X-200

74 Operating Instructions, 03/2015, C79000-G8976-C284-06

Permitted ambient conditions

Note Note the mounting position for XF and TS devices

With the following switches an ambient temperature of maximum +40 °C is permitted if the device is installed on a vertical rail:

•

XF204

•

XF208

•

XF204-2

•

XF206-1

•

XF204IRT

•

X204-2TS

•

X204-2LD TS

Type

Operating temperature

Storage/transport temperature

Rel. humidity in operation (no condensation)

Operating altitude at max. xx °C ambient temperature

X204-2

-40 °C to +60 ℃ -40 °C to +70 ℃ ‹ 95 % 2000 m at max. 56 ℃

3000 m at max. 50 ℃

X204-2TS

-40 °C to +70 ℃

-40 °C to +70 ℃ ‹ 95 % 2000 m at max. 56 ℃

3000 m at max. 50 ℃

X204-2FM

-40 °C to +60 ℃ -40 °C to +70 ℃ ‹ 95 % 2000 m at max. 56 ℃

3000 m at max. 50 ℃

X204-2LD

-40 °C to +60 ℃ -40 °C to +70 ℃ ‹ 95 % 2000 m at max. 56 ℃

3000 m at max. 50 ℃

X204-2LD TS

-40 °C to +70 °C

-40 °C to +70 ℃ ‹ 95 % 2000 m at max. 56 ℃

3000 m at max. 50 ℃

X206-1

-40 °C to +60 ℃ -40 ℃ to +70 ℃ ‹ 95 % 2000 m at max. 56 ℃

3000 m at max. 50 ℃

X206-1LD

-40 °C to +60 ℃ -40 °C to +70 ℃ ‹ 95 % 2000 m at max. 56 ℃

3000 m at max. 50 ℃

X208

-40 °C to +60 °C -40 ℃ to +70 ℃ ‹ 95 % 2000 m at max. 56 ℃

3000 m at max. 50 ℃

X208PRO

-40 ℃ to +70 ℃ -40 ℃ to +70 ℃ ‹ 95 % 2000 m at max. 56 ℃

3000 m at max. 50 ℃

X212-2

-40 °C to +60 ℃ -40 °C to +70 ℃ ‹ 95 % 2000 m at max. 56 ℃

3000 m at max. 50 ℃

X212-2LD

-40 °C to +60 ℃ -40 ℃ to +70 ℃ ‹ 95 % 2000 m at max. 56 ℃

3000 m at max. 50 ℃

X216

-40 ℃ to +60 ℃ -40 ℃ to +70 ℃ ‹ 95 % 2000 m at max. 56 ℃

3000 m at max. 50 ℃

X224

-40 ℃ to +60 ℃ -40 ℃ to +70 ℃ ‹ 95 % 2000 m at max. 56 ℃

3000 m at max. 50 ℃

XF204 *)

-40 °C to +60 °C -40 ℃ to +70 ℃ ‹ 95 % 2000 m at max. 56 ℃

3000 m at max. 50 ℃

XF204-2

-40 °C to +60 ℃

-40 °C to +70 ℃ ‹ 95 % 2000 m at max. 56 ℃

3000 m at max. 50 ℃

XF206-1

-40 °C to +60 ℃

-40 °C to +70 ℃ ‹ 95 % 2000 m at max. 56 ℃

3000 m at max. 50 ℃

Technical specifications

SCALANCE X-200 Operating Instructions, 03/2015, C79000-G8976-C284-06

Type

Operating temperature

Storage/transport temperature

Rel. humidity in operation (no condensation)

Operating altitude at max. xx °C ambient temperature

XF208

-40 °C to +60 ℃

-40 °C to +70 ℃ ‹ 95 % 2000 m at max. 56 ℃

3000 m at max. 50 ℃

X200-4P IRT

-25 ℃ to +40 ℃ -40 ℃ to +70 ℃ ‹ 95 % 2000 m at max. 35 ℃

3000 m at max. 30 ℃

X201-3P IRT

-25 ℃ to +50 ℃ -40 ℃ to +70 ℃ ‹ 95 % 2000 m at max. 45 ℃

3000 m at max. 40 ℃

X201-3P IRT PRO

-25 ℃ to +60 ℃ -40 °C to +70 ℃ ‹ 95 % 2000 m at max. 56 ℃

3000 m at max. 50 ℃

X202-2IRT

-40 °C to +60 ℃ -40 ℃ to +70 ℃ ‹ 95 % 2000 m at max. 56 ℃

3000 m at max. 50 ℃

X202-2P IRT

-25 ℃ to +60 ℃ -40 ℃ to +70 ℃ ‹ 95 % 2000 m at max. 56 ℃

3000 m at max. 50 ℃

X202-2P IRT PRO

-25 ℃ to +60 ℃ -40 °C to +70 ℃ ‹ 95 % 2000 m at max. 56 ℃

3000 m at max. 50 ℃

X204IRT

-40 °C to +70 ℃ -40 °C to +70 ℃ ‹ 95 % 2000 m at max. 56 ℃

3000 m at max. 50 ℃

X204IRT PRO

-25 ℃ to +70 ℃ -40 ℃ to +70 ℃ ‹ 95 % 2000 m at max. 56 ℃

3000 m at max. 50 ℃

XF204IRT

-40 °C to +60 ℃

-40 °C to +70 ℃ ‹ 95 % 2000 m at max. 56 ℃

3000 m at max. 50 ℃

Note the information on the mounting position above.

Frame delay times

The number of IE Switches X-200 connected in a line influences the frame delay.

Note Frame delay time with X-200 without IRT

When a frame passes through X

-200 IE switches, it is delayed by the Store&Forward

function of the X

-200 IE switches.

•

With a 64 byte frame length by approx. 10 microseconds (at 100 Mbps).

•

With a 1500 byte frame length by approx. 130 microseconds (at 100 Mbps).

This means that the more X-200 IE switches the frame passes through, the longer the frame delay.

Note Frame delay time with X-200 with IRT

The more X

-200IRT IE switches a frame runs through, the higher the frame delay. By using

the "cut through" switching mechanism, the X

-200IRT IE switches are ideal to meet the real-

time requirements of PROFINET.

Cut through is, however, not possible:

•

Between a port set to 10 Mbps and a port set to 100 Mbps.

•

When two packets are to be sent at the same time on one port.

In this case, an X-200 IE switch changes to Store&Forward and the delay increases.

Technical specifications

SCALANCE X-200

76 Operating Instructions, 03/2015, C79000-G8976-C284-06

SCALANCE X-200 Operating Instructions, 03/2015, C79000-G8976-C284-06

Figure A-1 Drilling pattern SCALANCE X204-2, X204-2TS, X204-2FM, X204-2LD, X204-2LD TS,

X206-1, X206-1LD, X208, X200-4P IRT, X201-3P IRT, X202-2IRT, X202-2P IRT, X204IRT

Dimension drawings

SCALANCE X-200

78 Operating Instructions, 03/2015, C79000-G8976-C284-06

Figure A-2 Drilling pattern SCALANCE X212-2, X212-2LD and X216

Dimension drawings

SCALANCE X-200 Operating Instructions, 03/2015, C79000-G8976-C284-06

Figure A-3 Drilling pattern SCALANCE X224

Figure A-4 Side view SCALANCE X-200

Dimension drawings

SCALANCE X-200

80 Operating Instructions, 03/2015, C79000-G8976-C284-06

Figure A-5 Side view SCALANCE X-200 POF with POF interface

Figure A-6 Dimension drawings of the SCALANCE X208PRO, SCALANCE X201-3P IRT PRO,

SCALANCE X202-2P IRT PRO and SCALANCE X204IRT PRO

Dimension drawings

SCALANCE X-200 Operating Instructions, 03/2015, C79000-G8976-C284-06

Figure A-7 Drilling pattern of the SCALANCE X208PRO, SCALANCE X201-3P IRT PRO,

SCALANCE X202-2P IRT PRO and SCALANCE X204IRT PRO

Dimension drawings

SCALANCE X-200

82 Operating Instructions, 03/2015, C79000-G8976-C284-06

Figure A-8 SCALANCE XF-200 dimension drawings

SCALANCE X-200 Operating Instructions, 03/2015, C79000-G8976-C284-06

Mechanical stability

Device type SCALANCE

IEC 60068-2-6 vibration

IEC 60068-2-27 shock

X204-2

5 – 9 Hz: 3.5 mm

9 – 500 Hz: 1 g

1 octave/min, 20 sweeps

15 g, 6 ms duration 6 shocks per axis

X204-2TS

5 – 9 Hz: 3.5 mm

9 – 500 Hz: 1 g

1 octave/min, 20 sweeps

5 – 150 Hz: Max. 7.9 g

random

15 g, 6 ms duration 6 shocks per axis

50 g, 30 ms duration 6 shocks per axis

X204-2FM

5 – 9 Hz: 3.5 mm

9 – 500 Hz: 1 g

1 octave/min, 20 sweeps

15 g, 6 ms duration 6 shocks per axis

X204-2LD

5 – 9 Hz: 3.5 mm

9 – 500 Hz: 1 g

1 octave/min, 20 sweeps

15 g, 11 ms duration 6 shocks per axis

X204-2LD TS

5 – 9 Hz: 3.5 mm

9 – 500 Hz: 1 g

1 octave/min, 20 sweeps

5 – 150 Hz: Max. 7.9 g

random

15 g, 6 ms duration 6 shocks per axis

50 g, 30 ms duration 6 shocks per axis

X206-1

5 – 9 Hz: 3.5 mm

9 – 500 Hz: 1 g

1 octave/min, 20 sweeps

15 g, 6 ms duration 6 shocks per axis

X206-1 LD

5 – 9 Hz: 3.5 mm

9 – 500 Hz: 1 g

1 octave/min, 20 sweeps

15 g, 6 ms duration 6 shocks per axis

X208

5 – 9 Hz: 3.5 mm

9 – 500 Hz: 1 g

1 octave/min, 20 sweeps

15 g, 6 ms duration 6 shocks per axis

X208PRO

5 - 9 Hz 3.5 mm

9 - 150 Hz 1 g

10 cycles

15 g, 11 ms duration 6 shocks/axis

X212-2

5 – 9 Hz: 3.5 mm

9 – 500 Hz: 1 g

1 octave/min, 20 sweeps

15 g, 11 ms duration 6 shocks per axis

X212-2LD

5 – 9 Hz: 3.5 mm

9 – 500 Hz: 1 g

1 octave/min, 20 sweeps

15 g, 6 ms duration 6 shocks per axis

X216

5 – 9 Hz: 3.5 mm

9 – 500 Hz: 1 g

1 octave/min, 20 sweeps

15 g, 11 ms duration 6 shocks per axis

X224

5 – 9 Hz: 3.5 mm

9 – 500 Hz: 1 g

1 octave/min, 20 sweeps

15 g, 11 ms duration 6 shocks per axis

XF204

5 – 9 Hz: 3.5 mm

9 – 500 Hz: 1 g

1 octave/min, 20 sweeps

15 g, 6 ms duration 6 shocks per axis

XF204-2

5 – 9 Hz: 3.5 mm

9 – 500 Hz: 1 g

1 octave/min, 20 sweeps

15 g, 6 ms duration 6 shocks per axis

Test of mechanical stability

SCALANCE X-200

84 Operating Instructions, 03/2015, C79000-G8976-C284-06

Device type SCALANCE

IEC 60068-2-6 vibration

IEC 60068-2-27 shock

XF206-1

5 – 9 Hz: 3.5 mm

9 – 500 Hz: 1 g

1 octave/min, 20 sweeps

15 g, 6 ms duration 6 shocks per axis

XF208

5 – 9 Hz: 3.5 mm

9 – 500 Hz: 1 g

1 octave/min, 20 sweeps

15 g, 6 ms duration 6 shocks per axis

X200-4P IRT

5 – 9 Hz: 3.5 mm

9 – 500 Hz: 1 g

1 octave/min, 20 sweeps

15 g, 11 ms duration 6 shocks per axis

X201-3P IRT

5 – 9 Hz: 3.5 mm

9 – 500 Hz: 1 g

1 octave/min, 20 sweeps

15 g, 11 ms duration 6 shocks per axis

X201-3P IRT PRO

5 – 9 Hz: 3.5 mm

9 – 150 Hz: 1 g

10 cycles per axis

15 g, 11 ms duration 6 shocks per axis

X202-2IRT

10 - 58 Hz: 0.075 mm

58 - 500 Hz: 1 g

10 cycles per axis

10 g, 16 ms duration 6 shocks per axis

X202-2P IRT

5 – 9 Hz: 3.5 mm

9 – 500 Hz: 1 g 1 octave/min, 20 sweeps

15 g, 11 ms duration 6 shocks per axis

X202-2P IRT PRO

5 – 9 Hz: 3.5 mm

9 – 150 Hz: 1 g

10 cycles per axis

15 g, 11 ms duration 6 shocks per axis

X204IRT

10 - 58 Hz: 0.075 mm

58 - 500 Hz: 1 g

10 cycles per axis

10 g, 16 ms duration 6 shocks per axis

X204IRT PRO

5 – 9 Hz: 3.5 mm

9 – 150 Hz: 1 g

10 cycles per axis

15 g, 11 ms duration 6 shocks per axis

XF204IRT

10 - 58 Hz: 0.075 mm

58 - 500 Hz: 1 g

10 cycles per axis

10 g, 16 ms duration 6 shocks per axis

Note

The interfaces of the X

-200 IE switches can be divided into groups each with 4 ports:

•

P1 to P4

•

P5 to P8

•

P9 to P12

•

etc.

If only ports of different port groups are used, the device meets the requirements for Environment B in compliance with IEEE 802.3, Section 33.4.1.1. If ports of the same port group are used, the requirements for Environment A are met.

SCALANCE X-200 Operating Instructions, 03/2015, C79000-G8976-C284-06

Service & Support

In addition to the product documentation, the comprehensive online information platform of Siemens Automation Customer Support supports at any time and at any location in the world. You will find the Service & Support pages on the Internet at the following address:

(

http://support.automation.siemens.com/WW/llisapi.dll?func=cslib.csinfo2&aktprim=99&lang=

en)

Apart from news, you will also find the following information there:

● Product information, Product Support, Applications & Tools

● Technical Forum

● Technical Support - Ask the Siemens experts

● Our service offer:

– Technical Consulting, Engineering support

– Field Service

– Spare parts and repairs

– Maintenance, optimization, modernization and more

You will find contact data on the Internet at the following address: (http://www.automation.siemens.com/partner/guiwelcome.asp?lang=en

)

Siemens SCALANCE X-200, SCALANCE XF200, X204-2, X204-2TS, X204-2FM Operating Instructions Manual

Specifications and Main Features

Frequently Asked Questions

User Manual