Page 1
Installation Instructions
Document No. 565-714
October 31, 2009
Veeder-Root D
These installationinstructionscovertheconnection of
the Veeder-RootDriverorthe Veeder-RootEnterprise
Driver to the Veeder-Root system only. For hardware
installation of the PXC Modular, see PXC Modular
Series Installation and Quick Start (553-638).
river for PXC Modular
Product Description
The Veeder-Root Driver enables communication
between the APOGEE
Veeder-Root system.
®
Automation System and the
Product Numbers
PXC00-PE96.A PXC Modular RS-485 or
Ethernet ALN, 96 FLN nodes
PXC00-E9
PXC100-PE96.A PXC Modular RS-485 or
PXC100-E96.A PXC Modular BACnet/IP ALN
PXX-485
LSM-INT-VR Veeder-Root PXC Modular
6.A
.3
PXC Modul
ALN and BA
96 FLN nod
Ethernet ALN, TX-I/O Support,
96 FLN nodes
and BACnet MS/TP ALN, TX-I/O
Support, 96 FLN nodes
Expansi
RS-485 F
Driver License
ar with BACnet/IP
Cnet MS/TP ALN,
es
on Module, three
LN connections
Warning/Caution Notations
WARNING:
Personal injury/loss of life may occur if you
do not follow the procedures as specified.
CAUTION:
Equipment d
occur if you
as specified
amage or loss of data may
do not follow the procedures
.
Expected Installation Times
The expected installation time is 30 minutes.
Required Tools and Materials
• Flat-blade screwdriver (1/8-inch blade width).
• Wire strippers.
• Cabling
the Veed
Device
and connectors. See the Connecting
er-Root Driver to the Veeder-Root
s section.
CAUTION:
Always
wrist s
static
compon
wear an electro-static discharge
trap and discharge accumulated
before touching field panel
ents.
LSM-INT-VRE Veeder-Root Enterprise PXC
ModularDriverLicense
Accessories
538-670
538-675
tem Number: 565-714, Rev. AA
I
Trunk Interface II, 115V
Trunk Interface II, 230V
Prerequisites
• Driver hardware is installed according t o its
respective installation instructions.
• FLN Termination blocks installed, if any.
Depending on the type of installation, other
prerequisites may have to be completed.
P
age 1 of 4
Page 2
Document No. 565-714
Installation Instructions
October 31, 2009
Connecting the Veeder-Root Driver
to the Veeder-Root Devices
Follow these steps to connect the Veeder-RootDriver
to the Veeder-Root system:
1. Make cables pe
2. Connect cables per diagram in Figure 1.
r diagram in Figure 1.
age 2 of 4
P
iemens Industry, Inc.
S
Page 3
Document No. 565-714
Installation Instructions
October 31, 2009
2
3
7
2
3
7
RS-485 TRUNK CABLE
(MAX 4000 ft / 1200 m;
STANDARD 24 AWG LOW CAPACITANCE)
TRUNK INTERFACE II
VEEDER-ROOT
TLS CONTROLLER
TAPE BACK
SHIELD
RS-232 25-PIN MALE TO
25-PIN MALE CABLE
(MAX 50 ft)
RS-232 PORT
(25-PIN FEMALE)
RS-232 PORT
(25-PIN FEMALE)
S
-
+
FLN
S
-
+
GROUND WIRE TO EARTH
(P/N 538-583)
POWER PACK
POWER
DRIVER
GW0768R3
Figure 1. Connecting the Veeder-Root Driver to the Veeder-Root Devices.
Siemens Industry, Inc. Page 3 of 4
Page 4
Document No. 565-714
Installation Instructions
October 31, 2009
Information in this document is based on specifications believed correct at the time of publication. The right is reserved to make changes as
design improvements are introduce d. Product or company names mentioned herein may be the trademarks of their respective owners.
© 2009 Siemens Industry, Inc.
Siemens Industry, Inc. Your feedback is important to us. If you have Document No. 565-714
1000 Deerfield Parkway comments about this document, send them to Country of Origin: US
Buffalo Grove, IL 60089-4513 SBT_technical.editor.us.sbt@siemens.com.
Page 4 of 4
U.S.A.
Loading...