SIEMENS TI351209RW Instruction Manual [fr]

Fully automatic espresso machine Machine à expresso automatique Volautomatische espressomachine

Ekspres do kawy Plně automatický kávovar

Автоматическая кофемашина

Kaffeevollautomat

TI351...

en Instruction manual ....................................................................... 5

fr Mode d’emploi ...........................................................................27

nl Gebruiksaanwijzing .................................................................... 51

pl Instrukcja obsługi ....................................................................... 75

cs Návod k použití .......................................................................... 99

ru ǪȋǻǽȃȆǻȊȉȆȗȂȉǽǻȈȃȚ ............................................................ 121

de Gebrauchsanleitung ................................................................. 145







, ,, ,,,

FOLF

,,,

FOLF

,9 9 9,

, ,, ,,,

,9 9 9,

, ,, ,,,

,,,,

Table of contents

enInstruction manual

8 Intended use. . . . . . . . . . . . . . . . . 6

( Important safety information . . . 6

7 Environmental protection . . . . . .8

Saving energy. . . . . . . . . . . . . . . . . . . 8

Environmentally-friendly disposal . . . . 8

Getting to know your appliance

Included in delivery. . . . . . . . . . . . . . . 9

Assembly and components . . . . . . . . 9

Controls . . . . . . . . . . . . . . . . . . . . . . 10

. . 9

_ Accessories . . . . . . . . . . . . . . . . 11

K Before using for the first time . 11

Installing and connecting the

appliance . . . . . . . . . . . . . . . . . . . . . 11

Commissioning the appliance . . . . . 11

1 Operating the appliance . . . . . . 13

Preparing coffee using freshly

ground beans . . . . . . . . . . . . . . . . . . 13

Preparing drinks with milk . . . . . . . . 13

Adjusting beverage settings . . . . . . . 14

Water filter . . . . . . . . . . . . . . . . . . . . 16

Frost protection. . . . . . . . . . . . . . . . . 16

. Service programme. . . . . . . . . . 21

Starting Calc’nClean . . . . . . . . . . . . . 22

3 Trouble shooting. . . . . . . . . . . . 23

4 Customer service . . . . . . . . . . . 26

Technical data. . . . . . . . . . . . . . . . . . 26

E number and FD number. . . . . . . . . 26

Guarantee . . . . . . . . . . . . . . . . . . . . . 26

1 Settings. . . . . . . . . . . . . . . . . . . . 17

Automatic switch-off . . . . . . . . . . . . . 17

Switching the audible signal on/off. . 17

Setting the water hardness . . . . . . . . 17

Factory reset. . . . . . . . . . . . . . . . . . . 18

D Daily care and cleaning. . . . . . . 19

Cleaning agent . . . . . . . . . . . . . . . . . 19

Cleaning the appliance. . . . . . . . . . . 19

Cleaning the drip tray and coffee

grounds container. . . . . . . . . . . . . . . 20

Cleaning the milk system . . . . . . . . . 20

Cleaning the brewing unit . . . . . . . . . 20

en Intended use

8 Intended use

Intended us e

Check the appliance for damage after unpacking it. Do not connect the appliance if it has been damaged in transport.

This appliance is intended for domestic use only.

Only use the appliance indoors at room temperature and up to 2000 m above sea level.

( Important safety

information

Import ant safet y informat i on

Please read carefully, follow and retain the operating instructions. When passing on the appliance, enclose these instructions.

This appliance can be used by children aged from 8years and above and by persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and if they understand the hazards involved. Keep children under 8years of age away from the appliance and connecting cable and do not allow them to use the appliance. Children shall not play with the appliance. Cleaning and user maintenance shall not be made by children unless they are older than 8years and supervised.

Important safety information en

:Warning

Danger of electric shock!

■ The appliance may only be

connected to a power supply with alternating current via a correctly installed socket with earthing. Ensure that the protective conductor system of the domestic electricity supply has been correctly installed.

Risk of electric shock!

■ Connect and operate the

appliance only in accordance with the specifications on the rating plate. If the power cord of this appliance is damaged, it must be replaced by customer service.

Risk of electric shock!

■ Do not use if the power

cable or appliance is damaged. If a fault occurs, pull the mains plug or switch off the mains voltage immediately.

Risk of electric shock!

■ To prevent hazards, the

appliance may be repaired by our customer service only.

Risk of electric shock!

■ Never immerse the

appliance or mains cord in water.

Risk of electric shock!

■ The plug and socket

connection of the appliance must not come into contact with liquids.

Risk of electric shock!

■ Please note the special

information on cleaning in the instructions.

:Warning

Hazard due to magnetism!

The appliance contains permanent magnets which may affect electronic implants, e.g. heart pacemakers or insulin pumps. Persons with electronic implants should keep a minimum distance of 10 cm from the appliance and the water tank when removed.

:Warning

Risk of suffocation!

Do not let children play with packaging material. Store small parts safely as they can be easily swallowed.

:Warning

Risk of burns!

■ The milk system becomes

very hot. After use, allow it to cool down first before touching it.

Risk of burns!

■ After use, surfaces may still

be hot for a certain period.

Risk of burns!

■ Freshly prepared beverages

are very hot.Leave to cool a little if necessary.

:Warning

Risk of injury!

■ Improper use of this

appliance may result in injury.

Risk of injury!

■ Do not reach into the

grinding unit.

en Environmental protection

:Warning

Fire hazard!

■ The appliance will become

hot.

Fire hazard!

■ Never operate the appliance

in a cupboard.

7 Environmental

protection

Envi r on mental pr otect i on

Saving energy

■ If the appliance is not being used,

switch it off.

■ Set the interval for automatic

switch-off to the smallest value.

■ If possible, do not interrupt coffee or

milk froth dispensing. Stopping a process prematurely results in higher energy consumption and the drip tray fills up more quickly.

■ Descale the appliance regularly to

avoid a build-up of limescale. Limescale residue results in higher energy consumption.

Environmentally-friendly disposal

Dispose of packaging in an environmentally-friendly manner.

This appliance is labelled in accordance with European Directive 2012/19/EU concerning used electrical and electronic appliances (waste electrical and electronic equipment - WEEE). The guideline determines the framework for the return and recycling of used appliances as applicable throughout the EU.

Please ask your dealer about current disposal routes.

Getting to know your appliance en

* Getting to know your

appliance

Gett i ng to know y our appl i ance

This section provides an overview of the scope of delivery, the assembly and the components of your appliance. It also introduces you to the different controls.

Note: Depending on the appliance

model, individual details and colours may differ.

How to use these instructions: The cover pages of the operating instructions can be folded out towards the front. The illustrations are identified using numbers that are referred to in the operating instructions. Example: ~ Fig. !

Included in delivery

~ Fig. !

# Fully automatic coffee machine + Water hardness testing strip 3 Instruction manual ; Milk frother

Assembly and components

~ Fig. "

( On / off button (stand-by mode) 0 Control panel 8 Handle of milk frother @ Outlet system for coffee, height

adjustable

H Milk frother (holder, frother, cover),

height adjustable

P Drip tray (coffee grounds

container, drip grate, drip plate, float)

X Door of brewing chamber ` Rating plate h Brewing unit )" Aroma lid )* Bean container )2 Rotary selector for setting grinding

level

): Cover for water tank )B Water tank

en Getting to know your appliance

Controls

Button Meaning

Switch the appliance on and off

espresso Dispensing Espresso caffe crema Dispensing Caffe crema cappuccino Dispensing cappuccino latte macchiato Dispensing latte macchiato milk Frothing up milk

% Coffee strength

calc’nClean Start the service programme

--------

Symbol

(

The appliance rinses automatically when it is switched on and off. The appliance is not rinsed if:

■ it is still warm when switched on, or

■ coffee was not dispensed before the appliance was switched off.

The appliance is ready for use when the LEDs of the buttons for selecting drinks light up in the control panel. The appliance has automatic switch-off. ~ "Selecting

automatic switch-off" on page 17

Adjusting the coffee strength ~ "Adjusting beverage settings" on page 14

Flashes when the service programme needs to be performed.~ "Calc’nClean

service programme" on page 22

Lights up when the water tank needs to be topped up with water or the water tank is not inserted. Flashes when the water filter needs to be replaced.

Lights up when trays need to be emptied. Flashes when door of brewing chamber is open.

is continu-

Ready to use, selection possible

ously lit is pulsing Dispensing underway is flashing Waiting for operation, e.g. with calc’nClean off Not available

--------

Accessories en

_ Accessories

Acc es so r i es

The following accessories are available

from retailers or from customer service:

Accessory Order number

Retail Customer ser-

Cleaning tablets TZ80001N 00311807 Descaling tablets TZ80002N 00576693 Water filter TZ70003 00575491 Care set TZ80004 00576330

--------

The contact data for customer service in all countries can be found at the back of these instructions.

vice

K Before using for the

first time

Bef o r e usi ng for the first time

In this section, you will learn how to

commission your appliance.

Note: Only use the appliance in

frost-free areas. If the appliance was transported or stored at temperatures below 0°C, you must wait for at least 3hours before using it.

Installing and connecting the appliance

1. Remove any protective plastic film.

2. Place the appliance on a level,

water-resistant surface which can bear the weight.

3. Using the mains plug, connect the

appliance to an earthed socket that has been correctly installed.

Note: After plugging in, always wait

(approx. 5 seconds).

Commissioning the appliance

Attaching milk frother

~ Fig. #

1. Remove milk frother parts from the

bag.

2. Assemble milk frother.

3. Attach the milk frother on the front of

the appliance.

Filling the bean container

This appliance can be used to make coffee drinks from coffee beans.

1. Open the lid )" of the bean

container )*.

2. Pour in coffee beans.

3. Close the lid again.

en Before using for the first time

Notes

■ Coffee beans that have been glazed

or caramelised or that contain other sugary additives block the brewing unit. Only use pure bean mixes that are suitable for use in fully automatic espresso or coffee machines.

■ The coffee beans are freshly ground

for each brewing process.

■ Keep the coffee beans sealed and

stored in a cool place to maintain optimum quality.

■ Coffee beans can be stored in the

bean container for a number of days without losing their aroma.

Filling the water tank

Important: Fill the water tank with fresh,

cold, still water on a daily basis. Prior to operation, check whether the water tank has been sufficiently filled.

1. Carefully remove the cover of the

water tank.

2. Use the handle to remove the water

tank and then rinse out.

3. Fill the water tank with water up to

the "max" marking.

4. Put the water tank back in the holder

again, keeping it straight, and fit the cover of the water tank.

General information

The factory settings of the fully automatic coffee machine are programmed for optimal performance.

■ The appliance switches off

automatically after a specific time.

■ Whenever a button is pressed, a

signal sounds. It can be switched off.~ "Settings" on page 17

■ When the appliance is used for the

first time, after running a service programme or has not been operated for a long period, the first beverage will not have the full aroma and should not be consumed.

■ After commissioning the appliance,

you will only achieve a suitably thick and stable "crema" after the first few cups have been dispensed.

■ If the appliance is in use for a long

period of time, water droplets will form on the ventilation slots. This is normal.

■ Escaping steam is not a fault but

due to the design of the machine.

Before using your new appliance, you should check and select the water hardness.~ "Settings" on page 17

Operating the appliance en

1 Operating the

appliance

Operat i ng the appl i anc e

In this section, you will learn how to make beverages with coffee and milk. It contains information about settings, water filters and adjustment of the grinding level, in addition to frost protection.

Note: Freshly prepared beverages may

be very hot.

Preparing coffee using freshly ground beans

You can choose between Espresso and Caffe crema. ~ "Preparing drinks with

milk" on page 13

The appliance is switched on. The water tank and bean container have been filled.

1. Place a cup under the outlet system.

2. Touch % repeatedly to select

the required coffee strength.

3. Touch the espresso or caffe crema

button. The coffee is brewed and then dispensed into the cup.

Preparing drinks with milk

This appliance has a milk frother. You can make drinks of coffee with milk or froth up milk.

Tip: You can also use plant-based

alternatives to milk, e.g. soya milk.

Notes

■ The quality of the milk froth depends

on the type of milk or the plant-based alternative used.

■ Dried milk residues are difficult to

remove so always perform cleaning.~ "Daily care and

cleaning" on page 19

:Warning

Risk of burns!

The milk frother gets very hot. Hold only by the handle. After use, let it cool down first before touching it.

Coffee drinks with milk

You can choose between cappuccino and latte macchiato. When doing so, please check the position of the coffee dispenser and milk frother.

Cappuccino

Note: To stop dispensing the drink

before the end, touch espresso or caffe crema again.

Latte Macchiato

The appliance is switched on. The water tank and bean container have been filled.

en Operating the appliance

The milk frother is installed.

1. Fill a large cup or a large glass with

approx. 100ml milk for cappuccino and approx. 150ml milk for latte macchiato.

2. Place a cup or a glass under the

outlet system.

3. Push the coffee dispenser and milk

frother right down.

4. Touch % repeatedly to select

the required coffee strength.

5. Touch the cappuccino or latte

macchiato button.

The milk is first frothed up in the cup or glass. The coffee is then brewed and dispensed into the cup or glass.

Note: To stop current dispensing of the

drink before the end, touch cappuccino or latte macchiato again.

Frothing up milk

The appliance is switched on. The water tank has been filled. The milk frother is installed.

1. Fill a large cup or a large glass with

approx. 100ml milk.

2. Place a cup or a glass under the

outlet system.

3. Push the coffee dispenser and milk

frother right down.

4. Touch the milk button.

The milk is frothed up.

Note: To stop the process before the

end, touch milkagain.

Adjusting beverage settings

Adj u s t i ng bever age set t ings

Coffee strength

Before making a drink, you can adjust the coffee strength:

To do so, touch % to select the strength you require.

mild

regular

strong

Note: The coffee strength selected is

then active for all drinks made with coffee.

Filling level

You can adjust the filling level of your drinks.

Press and hold espresso or caffe crema for 3 seconds.

Dispensing takes place, with the button selected flashing.

Once the required filling level is reached in the cup, touch the button selected to stop. The new filling level is only apparent after the next drink is dispensed.

Note: The filling level can be selected

either for Espresso (25- 60ml) or Caffe crema (80- 200ml).A minimum quantity is always brewed: Espresso approx. 25 ml and Caffe crema approx. 80 ml.

Operating the appliance en

Frothing time

You can adjust the frothing time of your drinks.

Press and hold cappuccino, latte macchiato or milk for 3 seconds.

The milk is frothed up, and the button selected flashes.

Once the required frothing time is reached, touch the button selected to stop.

Note: Setting the frothing time has no

impact on the amount of coffee.

Setting the grinding level

This appliance features an adjustable grinder. This enables the grinding level of the coffee to be individually changed.

:Warning

Risk of injury!

Do not reach into the grinding unit.

Caution!

The appliance may be damaged! Only adjust the grinding level when the grinder is running!

Notes

■ The new setting will not become

apparent until after the second cup of coffee.

■ Set a finer grinding level with

dark-roasted coffee beans and a coarser grinding level with lighter coffee beans.

When the grinder is in operation, use the rotary selector )2 to set the grinding level.

■ Finer grinding level: turn

anticlockwise. (Fig. a)

■ Coarser grinding level: turn

clockwise. (Fig. b)

D E

en Operating the appliance

Water filter

Wat er fil ter

~ Fig. '

A water filter lessens limescale deposits and reduces impurities in the water. The appliance also does not need to be descaled so often. Water filters are available from retailers or from customer service.

If a water filter is inserted, the appliance will show when this needs to be changed. The ) symbol is flashing.

Inserting or replacing a water filter

A new water filter must be rinsed before it can be used.

The appliance is switched on. The water tank has been filled.

1. Simultaneously hold down %

and calc’nClean for at least 3 seconds.

2. Touch espresso button, and "W.

hardness" will be activated.

3. Touch % button and make the

following selection:

with water filter

4. Immerse the water filter (opening

facing up) in a container filled with water until no more air bubbles rise to the surface. ~ Fig. '

5. Then press the water filter firmly into

the empty water tank.

6. Fill the water tank with water up to

the "max" marking.

7. Place a container with a capacity of

1.0litre under the outlet.

8. Touch espresso button to save the

setting and activate rinsing.

9. Insert water tank.

10. Touch espresso button to save the

setting and start rinsing. Water will now flow through the filter.

11. Touch calc’nClean button to exit the

menu.

12. Then empty the container. The

appliance is ready for use again.

Removing the water filter

If the water filter has been removed and no new one inserted, please select the appropriate water hardness. ~ "Setting

the water hardness" on page 17

Frost protection

To prevent frost damage during transportation and storage, the appliance must be completely emptied beforehand.

Info: The appliance must be ready for use and the water tank filled.

1. Place a large container under the

outlet of the milk frother and push the frother down.

2. Press and hold milk button for at

least 5 seconds. The LED in the button flashes, and the appliance now heats up.

3. As soon as steam escapes from the

milk frother, remove the water tank.

4. Allow the appliance to cool down.

Wait until ' symbol and all LEDs are flashing.

5. Use k button to switch the

appliance off.

6. Empty the water tank and the drip

tray and thoroughly clean the

appliance. The appliance can now be transported or stored.

Note: The brewing unit is now secured

and cannot be removed.

Settings en

1 Settings

Set t i n g s

This appliance has different factory settings. You can customise the settings on the appliance.

Note: If no button is pressed within

90 seconds, the appliance switches to "Choose beverage" without saving. The previous setting remains unchanged.

You can select the following settings:

Automatic switch-off

Sel ec t i n g aut omat i c swit ch-of f

The appliance switches off automatically at a specific time after the last button was pressed. This time can be selected, with settings from 15 minutes to 4 hours possible here.

1. Simultaneously hold down %

and calc’nClean for at least 3 seconds.

2. Touch caffe crema button and

"Automatic switch-off" will be activated.

3. Touch % button and select the

required time. The following settings are possible:

15 minutes 30 minutes (factory setting) 1 hour 2 hours 4 hours

4. Touch caffe crema button to save

the setting.

5. Touch calc’nClean button to exit the

menu.

Switching the audible signal on/off

Whenever a button is pressed, an audible signal sounds.

This can be switched on or off.

1. Simultaneously hold down %

and calc’nClean for at least 3 seconds.

2. Touch cappuccino button, and

"Signal tone" menu will be activated.

3. Touch % button and switch

signal tone on or off.

On (factory setting) Off

4. Touch cappuccino button to save

the setting.

5. Touch calc’nClean button to exit the

menu.

Setting the water hardness

It is important to set the water hardness correctly so that the appliance indicates in good time when the descaling programme should be run. The preset water hardness is level 4. You can check the water hardness using the enclosed test strip or by asking your local water supplier.

1. Briefly immerse the enclosed test

strip in fresh tap water, leave it to drip and read off the result after 1minute.

2. Simultaneously hold down %

and calc’nClean for at least 3 seconds.

3. Touch espresso button, and "W.

hardness" menu will be activated.

en Settings

4. Touch % button and select the

water hardness. The following settings are possible:

W. hardness 1 W. hardness 2 W. hardness 3 W. hardness 4(factory setting) Water filter (when used) H2O-softener (if available)

5. Touch espresso button to save the

setting.

6. Touch calc’nClean button to exit the

menu.

The table shows the allocation of the levels to the different degrees of water hardness:

Setting Degree of water hardness

German (°dH) French (°fH)

1 1-7 1-13 2 8-14 14-25 3 15-21 26-38 4 22-30 39-54

Factory reset

If you set the appliance back to the factory settings, you will lose your own settings.

1. Simultaneously hold down %

and calc’nClean for at least 3 seconds.

2. Touch latte macchiato button.

The factory settings are reactivated.

3. Touch calc’nClean button to exit the

menu.

Subsequent changes to the water hardness can be made at any time.

Note: When using the water filter (see

section "Accessories"), proceed as follows. ~ "Water filter" on page 16

Daily care and cleaning en

D Daily care and

cleaning

Dai l y care and cl eani ng

With good care and cleaning, your appliance will remain fully functioning for a long time to come. In this section, you will learn how to correctly clean and care for your appliance.

:Warning

Risk of electric shock!

Before cleaning the appliance, pull out the mains plug. Never immerse the appliance in water. Do not use a steam cleaner.

Cleaning agent

Please observe the following information to ensure that the different surfaces are not damaged by using the wrong type of cleaning agent.

Do not use:

■ Harsh or abrasive cleaning agents.

■ Any cleaning agents containing

alcohol or spirits.

■ Hard scouring pads or sponges.

Caution!

Not all of the appliance's components can be cleaned in the dishwasher.

~ Fig. % - '

Not dishwasher-safe:

Water tank Cover for water tank Aroma lid Brewing unit Drip tray

Dishwasher-safe:

Drip plate Drip grate Coffee grounds container

max. 60°C

Float Milk frother Cover for milk frother

Cleaning the appliance

1. Wipe down the outside of the

appliance with a soft, damp cloth.

2. Clean the control panel using a

micro-fibre cloth.

3. Wipe down the coffee dispenser if

required after dispensing each beverage.

Notes

■ New sponge cloths may contain

salts. Salts can cause rust film on stainless steel. Wash new sponge cloths thoroughly before use.

■ Always remove any limescale,

residues of coffee or milk, cleaning or descaling solution immediately.This residue may cause corrosion.

Notes

■ If the appliance is cold when

switched on or if it is switched off after dispensing coffee, it rinses automatically.The system is therefore self-cleaning.

■ If the appliance has not been used

for a long period of time (e.g. while you are on holiday), clean the entire appliance thoroughly, including the milk frother, trays and brewing unit.

en Daily care and cleaning

Cleaning the drip tray and

coffee grounds container

~ Fig. %

Note: The drip tray and coffee grounds

container should be emptied and

cleaned every day in order to prevent

deposits.With frequent use also empty

from time to time as soon as the float is

clearly visible if or the relevant symbol

lights up.

1. Open the door.

2. Pull the drip tray with the coffee

grounds container forwards and out.

3. Remove the drip plate with grate.

4. Empty and clean the drip tray and

coffee grounds container.

5. Wipe out the inside of the appliance

(area of drip tray).

Cleaning the milk system

Cleani ng the milk syst em

The milk system must be cleaned after

each use to remove residues.

:Warning

Risk of burns!

The milk frother gets very hot. Hold only

by the handle. After use, let it cool down

first before touching it.

1. Fill a glass half-full with water and

place under the outlet system.

2. Push the milk frother right down.

3. Touch the milk button to clean the

milk system.

4. Push the milk frother right up and

allow it to cool down.

5. Dismantle the milk frother into its

individual parts and clean thoroughly. ~ Fig. &

6. Dry the individual parts, reassemble

and fit back onto the appliance.

Notes

■ To stop the process before the end,

touch milk again.

■ All parts of the milk system should

be cleaned in the dishwasher. Detergent residues in the milk system must be thoroughly removed following the rinsing process.

Cleaning the brewing unit

~ Fig. $, ~ Fig. % In addition to automatic cleaning, the

brewing unit should be removed regularly for cleaning.

Caution!

Clean the brewing unit without detergent or products containing vinegar or acid and do not place in the dishwasher.

Remove the brewing unit:

1. Switch off the appliance.

2. Open the door to the brewing

chamber.

3. Remove the coffee grounds

container.

4. Push the red lever up, grasp the

brewing unit by the handle and pull forwards carefully.

5. Rinse the brewing unit thoroughly

under warm, running water.

6. Clean the interior of the appliance

thoroughly with a damp cloth, removing any coffee residues.

7. Allow the brewing unit and the

interior of the appliance to dry.

Insert the brewing unit:

1. Hold the brewing unit only by the

handle.

2. Push the red lever up, position the

brewing unit underneath and slide back as far as it will go. The lever must snap into place.

3. Insert the coffee grounds container

again and close the door.

Important: If the brewing unit has not been inserted, or the brewing unit or drip tray not inserted correctly, it will not be possible to close the door.

Service programme en

. Service programme

Ser v i c e pr ogr amme

The calc’nClean button will light up

every so often, with the exact frequency depending on the water hardness and usage of the appliance.

The appliance should be immediately cleaned and descaled using the programme.

Notes

■ Important: If the appliance is not

cleaned and descaled in good time, it may be damaged.

■ Caution! For each of the service

programmes, use Calc’nClean descaling and cleaning agents as described in the instructions and observe the (relevant) safety information.

■ Do not drink the liquids.

■ Never use citric acid, vinegar or any

vinegar-based agents to descale the appliance.

■ For cleaning and descaling, only use

the tablets intended for such purposes.They have been specially developed for this appliance, and new stocks can be ordered through customer service. ~ "Accessories"

on page 11

■ Never insert descaling tablets or

other products into the brewing unit.

■ Never interrupt the service

programme.

■ Prior to starting a service

programme, remove, clean and re-insert the brewing unit. Clean the milk frother.

■ At the end of a service programme,

wipe down the appliance using a soft, damp cloth to immediately remove any descaler residue. This residue may cause corrosion.

■ New sponge cloths may contain

salts. Salts can cause rust film on stainless steel, so cloths must always be washed out thoroughly before use.

■ Using a water filter increases the

intervals until a service programme needs to be performed.

■ If the service programme is

interrupted, e.g. by a power failure,

' and calc’nClean will light up.

Then proceed as follows:

1. Rinse out the water tank.

2. Pour in fresh, still water up to the

"max" marking.

3. Touch the calc’nClean button.

The programme starts and rinses the appliance.Duration: approx. 2 minutes.

4. Empty, clean and re-insert the drip

tray. Close the door. The programme has finished. The appliance is ready for use again.

en Service programme

Starting Calc’nClean

Cal c ’ n Cl ea n servi ce pr ogramme

Duration: approx. 40 minutes

1. Press and hold the calc’nClean

button for approx. 5 seconds.

( symbol lights up.

2. Open the door, remove the drip tray

and coffee grounds container and empty.

3. Remove and clean the brewing unit.

4. Place a Siemens cleaning tablet in

the brewing unit and re-insert the unit.

5. Re-insert the drip tray and coffee

grounds container and close the door.

' symbol lights up.

6. Remove the water filter (if there is

one).

7. Pour 0.5litres of lukewarm water

into the empty water tank up to the mark and dissolve a Siemens descaling tablet in it.

8. Re-insert the water tank and place a

large container (approx. 1 litre) under the outlet system.

9. calc’nClean flashes, touch

calc’nClean.

The programme starts, cleans and descales the appliance. calc’nClean pulses. Duration approx. 20 minutes. ( symbol lights up.

10. Empty the container, open the door,

empty the drip tray and re-insert.

11. Close the door and place a

container under the outlet system.

' symbol lights up.

12. Clean the water tank and replace the

water filter (if removed). ~ Fig. '

13. Fill with fresh, still water up to the

"max" mark. Place the container under the outlet system again.

14. calc’nClean flashes, touch

calc’nClean.

The programme starts and then cleans and rinses the appliance. calc’nClean pulses. ( symbol lights up.

15. Empty, clean and re-insert the drip

tray and coffee grounds container. The programme has finished. The appliance is ready for use again.

Trouble shooting en

3 Trouble shooting

Tr o ubl e s hooti ng

Faults often have simple explanations.

Before calling the customer service,

attempt to correct the fault yourself. Please read through the safety

information at the beginning of these instructions.

Fault table

Problem Reason Remedial action

please refer to the fault table and

The appliance no longer responds.

Coffee or milk froth quality varies considerably.

The individually selected per-cup quantity is not reached. Coffee dispensing slows to a trickle or stops completely

Fault in the appliance. Pull out the mains plug, wait

5 seconds, plug it back in.

Build-up of limescale in the appliance.

Descale the appliance in accordance

with the instructions. The grinding level is too fine. Set a coarser grinding level. Heavy build-up of limescale in

the appliance.

Descale the appliance as described in

the instructions. Air in the water filter. Immerse the water filter in water until

no more air bubbles escape, then

insert the filter again.

The quality of the milk froth varies.

The quality of the milk froth depends on the type of milk or the plant-based alternative

Optimise the result by selecting your

milk or plant-based alternative as

appropriate. used.

No coffee dispensed, only water.

An empty bean container is not detected by the appliance.

Add coffee beans

Note: The appliance will adjust to the

coffee beans on the next dispensing

process. The coffee shaft on the brewing

unit is blocked. Beans are not falling into the

grinding unit (beans too oily).

Clean the brewing unit. ~ "Cleaning

the brewing unit" on page 20

Gently tap the bean container.Possibly

change the type of coffee. When the

bean container is empty, wipe it with a

dry cloth.

Coffee has no “crema”. Unsuitable type of coffee. Use a type of coffee with a higher pro-

portion of robusta beans. The beans are no longer freshly

Use fresh beans. roasted.

The grinding level is not suita-

Set a finer grinding level. ble for the coffee beans.

The coffee is too "acidic". Grinding level set too coarse. Set a finer grinding level.

Unsuitable type of coffee. Use a darker roast.

The coffee is too "bitter". Coffee is ground too fine. Set a coarser grinding level.

Unsuitable type of coffee. Change the type of coffee.

en Trouble shooting

The coffee tastes "burnt". Coffee is ground too fine. Set a coarser grinding level.

Unsuitable type of coffee. Change the type of coffee.

Milk/blended milk drinks too hot. Milk froth too thin, loud sucking noise.

Milk/blended milk drinks too cold.

No milk/milk froth dispensed. The milk frother is soiled.

The water filter does not stay in position in the water tank.

Several buttons flashing, a loud noise can be heard.

Water dripped onto the inner floor of the appliance when the drip tray was removed.

The brewing unit cannot be removed.

The appliance cannot be operated, LEDs lit up or flashing.

The grinder will not start. The appliance is too hot. Wait 1hour so the appliance can cool

( LED flashes. The door is not properly closed. Press the door firmly closed.

( LED lit up despite empty

drip tray - what to do?

Too little milk in glass or cup. Use more milk or adjust frothing time.

Too much milk in glass or cup. Use less milk or adjust frothing time.

The milk frother is not inserted in the milk.

The water filter is not mounted correctly.

Water tank missing or wrongly inserted.

Drip tray removed too early. Wait a few seconds after the last drink

The brewing unit is not in the removal position (e.g. frost protection activated).

The appliance is in demo mode. Hold k button for at least 5 seconds

The appliance is too hot. Wait 1 hour so the appliance can cool

Emptying is not detected when the appliance is off.

Clean the milk frother in the dishwasher. ~ "Cleaning the milk system" on page 20 Use more milk, check whether the milk frother is inserted in the milk. Slide the outlet system right down.

Immerse the water filter into water until no more air bubbles escape; insert the filter again. Firmly press the water filter straight down into the tank connection.

Insert water tank correctly.

was dispensed before removing the drip tray.

Switch the appliance on again.

to deactivate demo mode.

down.

down. When the appliance is switched on,

remove and re-insert the drip tray.

Trouble shooting en

' LED lit up despite water tank being full.

Water tank wrongly inserted. Insert water tank correctly. Carbonated water in the water

Fill the water tank with fresh tap water. tank.

Float is stuck in the water tank. Remove the water tank and clean thor-

oughly. New water filter not rinsed

according to the instructions.

Rinse the water filter according to the

instructions and then switch on. Air in the water filter. Immerse the water filter (opening up)

in water until no more air bubbles

escape; insert the filter again.

~ "Inserting or replacing a water

filter" on page 16

Water filter is old. Insert a new water filter. Limescale deposits in the water

tank can block up the system.

Thoroughly clean the water tank and

start calc'nClean. ~ "Calc’nClean

service programme" on page 22

' LED flashes and all beverage LEDs flashing.

Water tank is missing or not inserted correctly.

The pipe system in the appliance is dry.

Insert water tank correctly.

Fill the water tank with fresh tap water.

Do not fill with carbonated water. Air in the water filter. Immerse the water filter (opening up)

in water until no more air bubbles

escape; insert the filter again.

~ "Inserting or replacing a water

filter" on page 16

All LEDs flashing. Incorrect voltage in building. Only operate the appliance at

220V-240V.

', ( and calc’nClean LEDs flashing.

( and % LEDs flashing. Brewing unit very heavily soiled

The ambient temperature is too cold.

or brewing unit cannot be removed.

Operate the appliance at temperatures

> 5 °C.

Clean brewing unit if possible and

switch appliance off and back on

again.

% LEDs flashing. Fault in the appliance. Restart appliance. calc’nClean and ) light up. The descaling process has

been interrupted.

Display "calc'nClean" keeps on

The water is too hard. Insert water filter and activate accord-

appearing.

Continue the descaling process.

~ "Service programme" on page 21

ing to the instructions. ~ "Water

filter" on page 16

If you are unable to solve the problem, always call the hotline. You will find the telephone numbers at the back of these instructions

--------

en Customer service

4 Customer service

Cus t o mer servi ce

Technical data

Power connection (voltage – frequency) 220–240V ∼, 50/60Hz Power rating 1300W Maximum static pump pressure 15bar Maximum water tank capacity (without filter) 1.3l Maximum capacity of the coffee bean container ≈ 250g Length of the power cable 100cm Dimensions (H x W x D) 37.3x 24.9x 42.8cm Weight, empty approx. 8–9kg Type of grinder Ceramic/steel

E number and FD number

When calling us, please give the full product number (E no.) and the production number (FD no.) so that we can provide you with the correct advice. These numbers can be found on the rating plate `. (~ Fig. ")

To save time, you can make a note of the data for your appliance and the telephone number for customer service here, should this be required.

E no.

Customer service O

The contact data for customer service in all countries can be found at the back of these instructions.

FD Number

Guarantee

The guarantee conditions for this appliance are as defined by our representative in the country in which it is sold. Details regarding these conditions can be obtained from the dealer from whom the appliance was purchased. The bill of sale or receipt must be produced when making any claim under the terms of this guarantee.

Changes reserved.

Table des matières

frMode d’ emploi

8 Utilisation conforme . . . . . . . . . 28

( Précautions de sécurité

importantes . . . . . . . . . . . . . . . . 28

7 Protection de l'environnement . 30

Économie d'énergie . . . . . . . . . . . . . 30

Elimination écologique . . . . . . . . . . . 30

* Présentation de l'appareil . . . . . 31

Contenu de l’emballage . . . . . . . . . . 31

Configuration et éléments. . . . . . . . . 31

Eléments de commande. . . . . . . . . . 32

D Entretien et nettoyage

quotidiens . . . . . . . . . . . . . . . . . 41

Nettoyants . . . . . . . . . . . . . . . . . . . . . 41

Nettoyage de l'appareil . . . . . . . . . . . 42

Nettoyer le bac d'égouttement et le

bac à marc de café. . . . . . . . . . . . . . 42

Nettoyage du système à lait . . . . . . . 42

Nettoyer l’unité de percolation. . . . . . 43

. Programme d’entretien. . . . . . . 44

Démarrer Calc’nClean. . . . . . . . . . . . 45

3 Anomalies, que faire ? . . . . . . . 46

_ Accessoires . . . . . . . . . . . . . . . . 33

K Avant la première utilisation. . . 33

Installation et raccordement de

l’appareil. . . . . . . . . . . . . . . . . . . . . . 33

Mise en service de l’appareil . . . . . . 33

1 Utilisation de l’appareil . . . . . . . 35

Préparer une boisson à base de café

en grains fraîchement moulus . . . . . 35

Préparation de boissons lactées . . . 35 Ajustage des réglages des boissons

Filtre à eau . . . . . . . . . . . . . . . . . . . . 38

Protection contre le gel. . . . . . . . . . . 38

. 36

1 Réglages. . . . . . . . . . . . . . . . . . . 39

Coupure automatique . . . . . . . . . . . 39

Activer/désactiver le signal sonore. . 39

Réglage de la dureté de l'eau . . . . . 39

Factory reset. . . . . . . . . . . . . . . . . . . 40

4 Service après-vente . . . . . . . . . 50

Données techniques . . . . . . . . . . . . . 50

Numéro E et numéro FD . . . . . . . . . . 50

Garantie. . . . . . . . . . . . . . . . . . . . . . . 50

fr Utilisation conforme

8 Utilisation conforme

Utilisation conf orme

Contrôler l'état de l'appareil après l'avoir déballé. Ne pas le raccorder s'il présente des avaries de transport.

Cet appareil est destiné exclusivement à une utilisation domestique et non professionnelle.

N’utilisez l’appareil que dans des pièces intérieures à température ambiante et jusqu’à 2000 m au-dessus du niveau de la mer.

( Précautions de

sécurité importantes

Précaut i ons de sécuri t é impor t ant es

Veuillez lire attentivement la notice d’utilisation, suivre les instructions qu’elle contient et conserver la notice. Si l’appareil change de propriétaire, remettez-lui cette notice.

L'appareil peut être utilisé par des enfants à partir de 8ans et par des personnes ayant des capacités physiques, sensorielles ou mentales restreintes ou ayant un manque d'expérience et/ou de connaissances s'ils sont sous surveillance ou ont été informés de la manipulation sûre de l'appareil et ont compris les dangers qui en résultent. Il faut maintenir les enfants de moins de 8ans à l’écart de l’appareil et du cordon de branchement et ne pas leur permettre d’utiliser l’appareil. Ne jamais permettre aux enfants de jouer avec l’appareil. Le nettoyage et l’entretien incombant à l’utilisateur ne doivent pas être effectués par des enfants sauf s’ils ont 8ans ou plus et sont surveillés.

:Mise en garde

Risque d’électrocution !

■ L'appareil doit être branché

uniquement sur un réseau à courant alternatif par l'intermédiaire d'une prise secteur installée de manière conforme et disposant d'une connexion à la terre. S'assurer que le système à conducteur de protection de l’installation électrique de la maison est conforme.

Risque d’électrocution !

■ Ne brancher et faire

fonctionner l’appareil que conformément aux indications figurant sur la plaque signalétique. En cas d'endommagement du cordon d'alimentation secteur, celui-ci doit être remplacé par le service après-vente.

Risque d’électrocution !

■ Ne l’utiliser que si le cordon

d’alimentation et l’appareil ne présentent aucun dégât. En cas de défaut, débrancher immédiatement la fiche secteur ou coupez la tension du réseau.

Risque d’électrocution !

■ Pour éviter tous risques, les

réparations de l’appareil sont réservées à notre service après-vente.

Risque d’électrocution !

■ Ne plongez jamais l’appareil

ou le cordon d’alimentation dans l’eau.

Risque d’électrocution !

■ Le raccordement de

l’appareil ne doit jamais entrer en contact avec des liquides.

Précautions de sécurité importantes fr

Risque d’électrocution !

■ Les instructions de nettoyage

spéciales figurant dans les notices sont à respecter.

:Mise en garde

Danger par magnétisme !

L'appareil contient des aimants permanents qui peuvent exercer une influence sur les implants électroniques tels que les stimulateurs cardiaques ou les pompes à insuline. Merci aux porteurs d'implants électroniques de respecter une distance d'au moins 10 cm entre eux et l'appareil et le réservoir d'eau retiré.

:Mise en garde

Risque d'étouffement !

Ne permettez jamais aux enfants de jouer avec les matériaux d’emballage. Rangez les petites pièces de manière sûre, elles pourraient être avalées.

:Mise en garde

Risque de brûlures !

■ Le système à lait devient très

chaud. Après utilisation, laisser refroidir avant de le toucher.

Risque de brûlure !

■ Les surfaces peuvent rester

chaudes pendant un certain temps après l’utilisation de l’appareil.

Risque de brûlure !

■ Les boissons fraîchement

préparées sont très chaudes.Si nécessaire, les laisser un peu refroidir.

fr Protection de l'environnement

:Mise en garde

Risque de blessure !

■ L’utilisation inappropriée de

l'appareil peut entraîner des blessures.

Risque de blessure !

■ Ne pas glisser les doigts à

l’intérieur du broyeur.

:Mise en garde

Risque d’incendie !

■ L'appareil devient chaud.

Risque d’incendie !

■ Ne jamais utiliser l'appareil

dans une armoire.

7 Protection de

l'environnement

Prot ec t i on de l'environnement

Économie d'énergie

■ Éteindre l'appareil quand celui-ci

n'est pas utilisé.

■ Régler l'intervalle d'arrêt

automatique sur la plus petite valeur.

■ Dans la mesure du possible, ne

jamais interrompre la distribution de café ou de mousse de lait. Une interruption conduit à une hausse de la consommation énergétique et à un remplissage accéléré des bacs collecteurs.

■ Détartrer régulièrement l’appareil

pour prévenir les dépôts de tartre. Les dépôts de tartre conduisent à une hausse de la consommation énergétique.

Elimination écologique

Eliminez l'emballage en respectant l'environnement.

Cet appareil est marqué selon la directive européenne 2012/19/UE relative aux appareils électriques et électroniques usagés (waste electrical and electronic equipment - WEEE). La directive définit le cadre pour une reprise et une récupération des appareils usagés applicables dans les pays de la CE.

S’informer auprès du revendeur sur la procédure actuelle de recyclage.

+ 146 hidden pages