Siemens SINUMERIK 840Di, SINUMERIK 810D, SINUMERIK 840D Operator's Manual

SINUMERIK 840D/840Di/810D

Operator's Guide

User Documentation

03.2002 Edition

CAD Reader

SINUMERIK 840D/840Di/810D CAD Reader

03.02 Edition

Operator's Guide

Introduction

How to Use the

CAD Reader

Additional Settings

Example of Application

Appendix

Index

Valid for

Control System Software Version

SINUMERIK 840D 6 SINUMERIK 840DE (export version) 6 SINUMERIK 840D (powerline) 6 SINUMERIK 840DE (powerline export version) 6 SINUMERIK 840Di 2 SINUMERIK 840DiE (export version) 2 SINUMERIK 810D 3 SINUMERIK 810DE (export version) 3 SINUMERIK 810D (powerline) 6 SINUMERIK 810DE (powerline export version) 6

SINUMERIK® Documentation

Printing history

Brief details of this edition and previous editions are listed below.

The status of each edition is shown by the code in the "Remarks" column.

Status code in the "Remarks" column:

A .... New documentation.

B .... Unrevised edition with new Order No.

C .... Revised edition with new status.

If factual changes have been made on the page since the last edition, this is indicated by a new edition coding in the header on that page.

Edition Order No. Comment

03.02 Included only in the online help A

This manual is included in the documentation available on CD ROM (DOCONCD)

Edition Order No. Comment

09.02 6FC5 298-6CA00-0BG3 C

Trademarks

SIMATIC

, SIMATIC HMIâ, SIMATIC NETâ, SIROTECâ, SINUMERIKâ and SIMODRIVEâ are registered trademarks of Siemens AG. Other names in this publication might be trademarks whose use by a third party for his own purposes may violate the rights of the registered holder.

Further information is available at web site: http: //www.ad .sieme ns.de /sinu merik

This publication was produced with WinW ord V8.0 and Designer V7.0 and DocuTool SinuTool. The reproduction, transmission or use of this document or its contents is not permitted without express written authority. Offenders will be liable for damages. All rights, including rights created by patent grant or registration of a utility model or design, are reserved.

Other functions not described in this documentation might be executable in the control. This does not, however, represent an obligation to supply such functions with a new control or when servicing.

We have checked that the contents of this document correspond to the hardware and software described. Nonetheless, differences might exist and we cannot therefore guarantee that they are completely identical. The information given in this publication is reviewed at regular intervals and any corrections that might be necessary are made in subsequent editions. We welcome suggestions for improvement.

Subject to change without prior notice.

Order No. Included only in the online help Printed in Germany

Siemens Aktiengesellschaft

03.02 Contents

Introduction 1-15

1.1 The CAD Reader product ................................................................................................. 1-16

1.2 General function................................................................................................................ 1-16

1.2.1 Scope of application ....................................................................................................1-17

1.2.2 Software....................................................................................................................... 1-17

1.2.3 Formats ....................................................................................................................... 1-18

1.2.4 Plane generation.......................................................................................................... 1-18

How to Use the CAD Reader 2-19

2.1 General operating procedures ..........................................................................................2-20

2.2 Define the zero point......................................................................................................... 2-21

2.3 Contour trace .................................................................................................................... 2-21

2.4 Drill points ......................................................................................................................... 2-23

2.5 Manipulate graphic display................................................................................................ 2-23

2.6 Process an imported file ................................................................................................... 2-24

Additional Settings 3-27

3.1 Additional settings and displays........................................................................................ 3-28

Example of Application 4-31

4.1 Example of application for a contour trace ....................................................................... 4-32

Appendix A-35

A References .........................................................................................................................A-35

I.1 Keyword Index ....................................................................................................................A-49

Contents 03.02

0-6 SINUMERIK 840D/840Di/810D Operator's Guide CAD Reader (CAD) – 03.02 Edition

Notes

03.02 Preface

Structure of manual

Preface

Organization of

documentation

SINUMERIK documentation is organized on 2 separate levels:

• General Documentation

• User documentation

Target group

This Manual is intended for machine-tool users. This publication provides detailed information that the user needs to operate this application for the SINUMERIK 840D/840Di/810D controls.

Hotline

If you have any queries, please contact the Hotline given below:

A&D Technical Support Tel.: ++49-180-5050-222

Fax: ++49-180-5050-223

If you have any questions about the documentation (suggestions, corrections), please send a fax to the following fax address or email:

A&D Technical Support Tel.: ++49-9131-98-2176

Email: motioncontrol.docu@erlf.siemens.de

Fax form: See Suggestions/Corrections Sheet at the back of the document.

Internet address

http://www.ad.siemens.de/sinumerik

Objectives

This Operator's Guide describes the CAD Reader PC application and how to use it. The CAD Reader enables you to convert drawings constructed with a CAD system for further processing on a

SINUMERIK control. The format of the imported file is DXF (Drawing

eXchange Format) from which contours or drill points are filtered out.

Note

The CAD Reader can be used for systems with the following software versions: Controls SINUMERIK 840D/840Di/810D All versions Target systems HMI Advanced or HMI Embedded SW 5.1 and higher

ShopMill and ManualTurn SW 5.3 and higher ShopTurn SW 6.2 and higher

Please note the supplementary conditions regarding the number of cycles.

Preface 03.02

Structure of manual

0-8 SINUMERIK 840D/840Di/810D Operator's Guide CAD Reader (CAD) – 03.02 Edition

Search tools

A table of contents and keyword index are provided to help you access information quickly.

SINUMERIK 840D

powerline

Improved performance versions

• SINUMERIK 840D powerline and

• SINUMERIK 840DE powerline

are available from 09.2001 onwards.

For a list of available powerline modules, please refer to the

Hardware Description:

References: /PHD/ Configuring Manual SINUMERIK 840D

SINUMERIK 810D

powerline

Improved performance versions

• SINUMERIK 810D powerline and

• SINUMERIK 810DE powerline

are available from 03.2002 onwards.

For a list of available powerline modules, please refer to the

Hardware Description:

References: /PHC/ Configuring Manual SINUMERIK 810D

Standard scope

This Operator's Guide describes the functionality afforded by standard functions. Differences and additions implemented by the machine-tool manufacturer are documented by the machine-tool manufacturer.

Please consult your local Siemens office for more detailed information about other SINUMERIK 840D, 840Di and 810D as well as the publications that apply to all SINUMERIK controls (e.g. Universal Interface, Measuring Cycles ...).

Other functions not described in this documentation might be executable in the control. This does not, however, represent an obligation to supply such functions with a new control or when servicing.

Applicability

Catalog NC 60 is the definitive document as regards the validity of functions /BU/ Ordering Information, Catalog NC 60.

03.02 Preface

Structure of manual

Structure of descriptions

All functions and operating options have been described according to the same internal structure as far as this is meaningful and practicable. The various levels of information have been structured so that you can find the information you are looking for quickly.

1. Function

This theoretical section is primarily intended as learning material for the NC beginner. It provides important information that will help you to understand the principle of operating functions. You should work through the manual at least once to get an idea of the scope of the functions and capability of your SINUMERIK control.

2. Operating sequence

This section provides a clear diagrammatic description of the sequence of key inputs required. If inputs have to be made at individual stages of the sequence or if you require additional information, you will find this next to the key illustrations.

3. Further notes

For safety reasons, some of the functions are protected from access by unauthorized persons. The machine-tool manufacturer can influence or modify the described functions. Please follow the instructions of the machine-tool manufacturer.

Preface 03.02

Structure of manual

0-10 SINUMERIK 840D/840Di/810D Operator's Guide CAD Reader (CAD) – 03.02 Edition

Explanation of symbols

Function

Operating sequence

Further notes

Cross-references to other documentation or sections

Danger notes

Additional notes or background information

Ordering data option

Explanation

Description of syntax

Programming examples

03.02 Preface

Rules for proper use

The following special notes have been used in this documentation:

Notes

This symbol appears in this documentation whenever it is necessary to draw your attention to an important item of information.

In this documentation, you will find this symbol with a reference to an ordering option. The function described is executable only if the control contains the designated option.

Warnings

The following warning notes with varying degrees of severity are used in the documentation:

Danger

Indicates an imminently hazardous situation which, if not avoided, will

result in death or serious injury or in substantial property damage.

Warning

Indicates a potentially hazardous situation which, if not avoided, could

result in death or serious injury or in substantial property damage.

Caution

Used with the safety alert symbol indicates a potentially hazardous

situation which, if not avoided, may result in minor or moderate injury

or in property damage.

Caution

Used without safety alert symbol indicates a potentially hazardous

situation which, if not avoided, may result in property damage.

Notice

Used without the safety alert symbol indicates a potential situation

which, if not avoided, may result in an undesirable result or state.

References

This symbol appears whenever specific information can be found in other literature. A complete list of available literature is included in the Appendix of this Operator's Guide.

Preface 03.02

Rules for proper use

0-12 SINUMERIK 840D/840Di/810D Operator's Guide CAD Reader (CAD) – 03.02 Edition

Principle

Your SIEMENS 840D/840Di/810D has been designed and constructed according to state-of-the-art technology and approved safety regulations and standards.

Additional equipment

The applications of SIEMENS controls can be expanded by adding special additional devices, equipment and expansions supplied by SIEMENS.

Personnel Only appropriately trained, authorized and reliable personnel may

be allowed to operate this equipment. No-one without the necessary training must be allowed to operate the control, even temporarily.

The corresponding responsibilities of personnel who set up, operate

and maintain the equipment must be clearly defined and adherence to

these responsibilities monitored.

Procedure Before the control is started up, the personnel who will work on the

control system must become thoroughly acquainted with the

Operator's Guide. It is also the duty of the equipment operator to

constantly monitor the overall technical condition of the control

(outwardly apparent defects or damage as well as changes in operating performance).

03.02 Preface

Rules for proper use

Service Repairs must be carried out by personnel who are specially trained

and qualified in the relevant technical subject according to the

information supplied in the service and maintenance guide. All relevan

safety regulations must be followed.

The following is deemed to be improper usage and exempts the

manufacturer from any liability:

Any application which does not comply with the rules for proper usage

described above.

If the control is not in technically perfect condition, or is operated

without due regard for safety regulations and accident prevention instructions given in the Instruction Manual.

If faults that might affect the safety of the equipment are not rectified

before the control is started up.

Any modification, bypassing or disabling of items of equipment on

the control that are required to ensure fault-free operation, unlimited use and active and passive safety.

Improper usage gives rise to unforeseen dangers to:

• Life and limb of personnel,

• The control, machine or other assets of the owner and the user

Preface 03.02

Rules for proper use

0-14 SINUMERIK 840D/840Di/810D Operator's Guide CAD Reader (CAD) – 03.02 Edition

Notes

03.02 Introduction

Introduction

1.1 The CAD Reader product................................................................................................ 1-16

1.2 General function .............................................................................................................. 1-16

1.2.1 Scope of application .................................................................................................. 1-17

1.2.2 Software .................................................................................................................... 1-17

1.2.3 Formats ..................................................................................................................... 1-18

1.2.4 Plane generation ....................................................................................................... 1-18

Introduction 03.02

1.1 The CAD Reader product

1-16 SINUMERIK 840D/840Di/810D Operator's Guide CAD Reader (CAD) – 03.02 Edition

1.1 The CAD Reader product

Description

The CAD Reader program converts files of CAD drawings into

contours or drill patterns for SINUMERIK 840D/840Di/810D.

Functions

The following functions can be converted by the CAD Reader:

• Import DXF files

• Hide graphics layers

• Automatic contour trace

• Optional workpiece zero per contour/drill point

• Several contours/drill points can be selected simultaneously

• Create and convert contours or drill patterns for ShopMill,

ShopTurn, ManualTurn, HMI Advanced or HMI Embedded

• Display existing contours/drill points in geometry processor/cycles

support.

1.2 General function

General function

The CAD Reader enables you to convert drawings constructed with a

CAD system for further processing on a SINUMERIK control. The

format of the imported file is DXF (Drawing eX

change Format) from

which contours or drill points are filtered out. Any information that is

not needed for further processing (such as dimensions, hatching,

labels, borders) can be removed.

Existing contours or drill patterns are converted such that they can be

interpreted by the geometry processor or the cycles support.

+ 36 hidden pages

Siemens SINUMERIK 840Di, SINUMERIK 810D, SINUMERIK 840D Operator's Manual

Specifications and Main Features

Frequently Asked Questions

User Manual