Siemens SICAM Q200 7KG97 User Manual
Preface
Open Source Software
Table of Contents
SICAM
Multifunctional Recorder
SICAM Q200 7KG97
Communication
V02.00
Manual
User Information
Communication Modbus
Communication IEC 61850
Glossary
1
2
3
E50417-C1040-C606-A3
i
i
NOTE
For your own safety, observe the warnings and safety instructions contained in this document, if available.
Disclaimer of Liability
This document has been subjected to rigorous technical
review before being published. It is revised at regular intervals, and any modifications and amendments are included
in the subsequent issues. The content of this document has
been compiled for information purposes only. Although
Siemens AG has made best efforts to keep the document as
precise and up-to-date as possible, Siemens AG shall not
assume any liability for defects and damage which result
through use of the information contained herein.
This content does not form part of a contract or of business
relations; nor does it change these. All obligations of
Siemens AG are stated in the relevant contractual agreements.
Siemens AG reserves the right to revise this document from
time to time.
Document version: E50417-C1040-C606-A3.02
Edition: 03.2017
Version of the product described: V02.00
Copyright
Copyright © Siemens AG 2017. All rights reserved.
The disclosure, duplication, distribution and editing of this
document, or utilization and communication of the content
are not permitted, unless authorized in writing. All rights,
including rights created by patent grant or registration of a
utility model or a design, are reserved.
Registered Trademarks
SIPROTEC®, DIGSI®, SIGUARD®, SIMEAS®, and SICAM® are
registered trademarks of Siemens AG. Any unauthorized
use is illegal. All other designations in this document can
be trademarks whose use by third parties for their own
purposes can infringe the rights of the owner.
Preface
IND. CONT. EQ.
69CA
Purpose of the Manual
This manual describes the communication of the SICAM Q200 device.
Target Audience
This manual is intended for project engineers, commissioning and operating personnel in electrical systems
and power plants.
Scope
This manual is valid for SICAM Q200.
Indication of Conformity
This product complies with the directive of the Council of the European Communities
on harmonization of the laws of the Member States relating to electromagnetic
compatibility (EMC Directive 2014/30/EU) and concerning electrical equipment for use
within specified voltage limits (Low Voltage Directive 2014/35/EU).
This conformity has been proved by tests performed according to the Council Directive
in accordance with the generic standard EN 61000-6-5 (for EMC directive) and with the
product standard EN 62586-1 (for Low Voltage Directive) by Siemens AG
The device is designed and manufactured for application in an industrial environment.
The product conforms with the international standards of EN 62586 and the German
standard VDE 0415.
Other Standards
This product is UL-certified to Standard UL 61010-1, third edition, based on the Technical data.
(UL File No.: E228586)
Open-type Measuring Equipment
2UD1
For further information see UL database on the internet: http://ul.com.
Select Online Certifications Directory and insert E228586 under UL File Number.
Additional Support
For questions about the system, please contact your Siemens sales partner.
Support
Our Customer Support Center provides a 24-hour service.
Phone:
Fax: +49 (180) 524-2471
SICAM, Multifunctional Recorder, Manual 3
E50417-C1040-C606-A3, Edition 03.2017
+49 (180) 524-7000
!
!
!
Preface
E-Mail: support.energy@siemens.com
Training Courses
Inquiries regarding individual training courses should be addressed to our Training Center:
Siemens AG
Siemens Power Academy TD
Humboldtstraße 59
90459 Nürnberg
Germany
Phone: +49 (911) 433-7415
Fax: +49 (911) 433-7929
E-Mail: poweracademy@siemens.com
Internet: www.siemens.com/poweracademy
Notes on Safety
This document is not a complete index of all safety measures required for operation of the equipment (module
or device). However, it comprises important information that must be followed for personal safety, as well as
to avoid material damage. Information is highlighted and illustrated as follows according to the degree of
danger:
DANGER
DANGER means that death or severe injury will result if the measures specified are not taken.
Comply with all instructions, in order to avoid death or severe injuries.
²
WARNING
WARNING means that death or severe injury may result if the measures specified are not taken.
Comply with all instructions, in order to avoid death or severe injuries.
²
CAUTION
CAUTION means that medium-severe or slight injuries can occur if the specified measures are not taken.
Comply with all instructions, in order to avoid moderate or minor injuries.
²
NOTICE
NOTICE means that property damage can result if the measures specified are not taken.
Comply with all instructions, in order to avoid property damage.
²
4 SICAM, Multifunctional Recorder, Manual
E50417-C1040-C606-A3, Edition 03.2017
i
i
NOTE
Important information about the product, product handling or a certain section of the documentation
which must be given particular attention.
Qualified Electrical Engineering Personnel
Only qualified electrical engineering personnel may commission and operate the equipment (module, device)
described in this document. Qualified electrical engineering personnel in the sense of this manual are people
who can demonstrate technical qualifications as electrical technicians. These persons may commission,
isolate, ground and label devices, systems and circuits according to the standards of safety engineering.
Proper Use
The equipment (device, module) may be used only for such applications as set out in the catalogs and the
technical description, and only in combination with third-party equipment recommended and approved by
Siemens.
Problem-free and safe operation of the product depends on the following:
Proper transport
•
Proper storage, setup and installation
•
Proper operation and maintenance
•
When electrical equipment is operated, hazardous voltages are inevitably present in certain parts. If proper
action is not taken, death, severe injury or property damage can result:
The equipment must be grounded at the grounding terminal before any connections are made.
•
All circuit components connected to the power supply may be subject to dangerous voltage.
•
Hazardous voltages may be present in equipment even after the supply voltage has been disconnected
•
(capacitors can still be charged).
Preface
•
•
Used Symbols
No.
1 Direct current
2 Alternating current
3 Direct and alternating current
4 3-phase alternating current
5 Earth (ground) terminal
6 Protective conductor terminal
Operation of equipment with exposed current-transformer circuits is prohibited. Before disconnecting the
equipment, ensure that the current-transformer circuits are short-circuited.
The limiting values stated in the document must not be exceeded. This must also be considered during
testing and commissioning.
Symbol Description
IEC 60417-5031
IEC 60417-5032
IEC 60417-5033
IEC 60417-5017
IEC 60417-5019
SICAM, Multifunctional Recorder, Manual 5
E50417-C1040-C606-A3, Edition 03.2017
6 SICAM, Multifunctional Recorder, Manual
E50417-C1040-C606-A3, Edition 03.2017
Open Source Software
The product contains, among other things, Open Source Software developed by third parties. The Open
Source Software used in the product and the license agreements concerning this software can be found in the
Readme_OSS. These Open Source Software files are protected by copyright. Your compliance with those
license conditions will entitle you to use the Open Source Software as foreseen in the relevant license. In the
event of conflicts between Siemens license conditions and the Open Source Software license conditions, the
Open Source Software conditions shall prevail with respect to the Open Source Software portions of the software. The Open Source Software is licensed royalty-free. Insofar as the applicable Open Source Software
License Conditions provide for it you can order the source code of the Open Source Software from your
Siemens sales contact - against payment of the shipping and handling charges - for a period of at least 3 years
since purchase of the Product. We are liable for the Product including the Open Source Software contained in
it pursuant to the license conditions applicable to the Product. Any liability for the Open Source Software
beyond the program flow intended for the Product is explicitly excluded. Furthermore any liability for defects
resulting from modifications to the Open Source Software by you or third parties is excluded. We do not
provide any technical support for the Product if it has been modified.
SICAM, Multifunctional Recorder, Manual
E50417-C1040-C606-A3, Edition 03.2017
7
8 SICAM, Multifunctional Recorder, Manual
E50417-C1040-C606-A3, Edition 03.2017
Table of Contents
Preface..........................................................................................................................................................3
Open Source Software..................................................................................................................................7
1 User Information........................................................................................................................................ 11
1.1 General User Information.................................................................................................. 12
2 Communication Modbus............................................................................................................................ 13
2.1 Functions, Properties and Exception Responses for Modbus TCP Server and Modbus
RTU (Slave)....................................................................................................................... 14
2.2 Functions and Properties for Modbus RTU Master.............................................................. 16
2.3 Exception Responses from the Modbus Gateway............................................................... 18
2.4 Modbus Registers..............................................................................................................19
2.4.1 Modbus Specifications................................................................................................. 19
2.4.2 Mapping Documentation of the SICAM Devices............................................................ 19
2.5 Modbus Data Format.........................................................................................................21
2.5.1 Data Types - General....................................................................................................21
2.5.2 Data Type - Measured Value (Read)..............................................................................21
2.5.3 Data Type - Date/Time (Read and Write)....................................................................... 23
2.5.4 Data Type - Indications (Read)......................................................................................24
2.5.5 Data Type - Controllable Indications (Read and Write)...................................................24
2.5.6 Data Type - Counter (Read).......................................................................................... 25
3 Communication IEC 61850......................................................................................................................... 27
3.1 General.............................................................................................................................28
Glossary...................................................................................................................................................... 29
SICAM, Multifunctional Recorder, Manual 9
E50417-C1040-C606-A3, Edition 03.2017
Loading...