Siemens HiPath 2000, HiPath 3000, HiPath 5000, optiPoint 420 advance, optiPoint self labeling key module Operating Instructions Manual
HiPath 2000
HiPath 3000
HiPath 5000
optiPoint 420 advance
optiPoint
self labeling key module
Operating Instructions
Before You Begin
Before You Begin
These operating instructions describe the optiPoint 420 advance telephone on your
HiPath 2000 and HiPath 3000 / 5000.
They describe all functions you can use from your telephone. You may find that some functions you wish to use are not available on your telephone. This may be due to one of the
following reasons:
• The function has not been configured for your telephone - address any questions to
your service personnel.
• Your communications platform does not support this function - contact your service
personnel to upgrade your system.
Important Notes
Do not operate the telephone in environments where there is a danger of
explosions.
Use only original Siemens accessories. Using other accessories may cause
a hazard and will invalidate the warranty and the CE mark.
Never open the telephone or a key module. If you encounter any problems,
contact your service personnel.
CE (customer equipment) does not continue to support emergency dialing after loss of
mains power, if battery back up and power fail switchover to emergency analogue phones
is not available.
Never allow the telephone to come into contact with staining or aggressive liquids such as
coffee, tea, juice, or soft drinks. For information on telephone maintenance ! Page 125.
The information provided in this document contains merely general descriptions or characteristics of performance which in case of actual use do not always apply as described or
which may change as a result of further development of the products.
An obligation to provide the respective characteristics shall only exist if expressly agreed
in the terms of contract.
The trademarks used are owned by Siemens AG or their respective owners.
2
Marks
Before You Begin
The device conforms to the EU guideline 1999/5/EG, as attested by the CE
mark.
This device has been manufactured in accordance with our certified environmental management system (ISO 14001). This process ensures that energy
consumption and the use of primary raw materials are kept to a minimum,
thus reducing waste production.
All electrical and electronic products should be disposed of separately from
the municipal waste stream via designated collection facilities appointed by
the government or the local authorities.
The correct disposal and separate collection of your old appliance will help
prevent potential negative consequences for the environment and human
health. It is a precondition for reuse and recycling of used electrical and electronic equipment.
For more detailed information about disposal of your old appliance, please
contact your city office, waste disposal service, the shop where you purchased the product or your sales representative.
The statements quoted above are only fully valid for equipment which is installed and sold in the countries of the European Union and is covered by
the directive 2002/96/EC. Countries outside the European Union may have
other regulations regarding the disposal of electrical and electronic equipment.
3
Contents
Contents
Before You Begin. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
Important Notes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Marks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Basic operating instructions . . . . . . . . . . . . . . . . . . . .9
optiPoint 420 advance and
optiPoint self labeling key module control panel . . . . . . . . . . . . . . . . . . 9
How to Use these Operating Instructions. . . . . . . . . . . . . . . . . . . . . . . 10
Displays . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Accessing Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
... Interactively . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
... Via the Program/Service Menu . . . . . . . . . . . . . . . . . . . . . . . . . . 12
... With Function Keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Functions You Can Use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Self Labelling Key Function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Basic and Enhanced Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Additional Team and Executive/Secretary Functions. . . . . . . . . . . . 13
Using the Telephone Efficiently. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Safety Precautions for IP Telephony . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Making Calls – Basic Functions . . . . . . . . . . . . . . . .15
Answering Calls. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Answering a Call With the Handset. . . . . . . . . . . . . . . . . . . . . . . . . 15
Answering a Call with the Speaker (Speakerphone Mode) . . . . . . . 15
Switching to Speakerphone Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Switching to the Handset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Open Listening in the Room During a Call . . . . . . . . . . . . . . . . . . . . . . 17
Making Calls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Off-Hook Dialing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
On-Hook Dialing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Ending the call . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Redialing a Number . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Turning the Microphone On and Off . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Calling a Second Party (Consultation Hold) . . . . . . . . . . . . . . . . . . . . . . 21
Switching to the Party on Hold (Toggle) . . . . . . . . . . . . . . . . . . . . . 21
Transferring a Call . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Call Forwarding . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Using Variable Call Forwarding . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Using Call Forwarding No Reply (CFNR) . . . . . . . . . . . . . . . . . . . . . 24
Call Forwarding in the Carrier Network
and Forwarding Multiple Subscriber Numbers (MSN) (Not for U.S.) 25
Call Forwarding in the Event of a Telephone Malfunction . . . . . . . . 26
4
Contents
Using Callback . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Storing a Callback. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Answering a Callback. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Checking and Canceling a Saved Callback . . . . . . . . . . . . . . . . . . . . 27
Saving Repertory Dialing Numbers on a Key. . . . . . . . . . . . . . . . . . . . . 29
Using Repertory Dialing Keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Telephone Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Adjusting the Ring Volume . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Adjusting the Ring Tone. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Adjusting the Attention Ring Volume. . . . . . . . . . . . . . . . . . . . . . . . 32
Adjusting the display contrast . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Adjusting the key label contrast. . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Adjusting the Speakerphone to the Room Acoustics . . . . . . . . . . . 33
Adjusting the Receiving Volume During a Call. . . . . . . . . . . . . . . . . 34
Adjusting the Display to a Comfortable Reading Angle . . . . . . . . . . 34
Display backlight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Selecting the Language of Screen Prompts . . . . . . . . . . . . . . . . . . 34
Making Calls – Convenience Functions . . . . . . . . .35
Answering Calls. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Accepting a Specific Call for Your Colleague . . . . . . . . . . . . . . . . . . 35
Rejecting Calls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Using the Speakerphone . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Answering a Call With a Headset . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Answering Calls from the
Entrance Telephone and Opening the Door. . . . . . . . . . . . . . . . . . . 38
Accepting a Call From an Answering Machine . . . . . . . . . . . . . . . . 39
Dialing/Making Calls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
En-Bloc Sending / Correcting Numbers . . . . . . . . . . . . . . . . . . . . . . 40
Using a Caller List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
Speed-dial . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
Dialing a Number From the Internal Directory . . . . . . . . . . . . . . . . . 45
Dialing from the Telephone Database (LDAP) . . . . . . . . . . . . . . . . . 47
Using Mailboxes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
Talking to Your Colleague With a Speaker Call . . . . . . . . . . . . . . . . 49
Talking to Your Colleague with Discreet Calling . . . . . . . . . . . . . . . 50
Automatic Connection Setup (Hotline). . . . . . . . . . . . . . . . . . . . . . . 50
Reserve Trunk . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
Assigning a Station Number (Not for U.S.) . . . . . . . . . . . . . . . . . . . 51
Associated Dialing/Dialing Aid . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
During a Call . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
Using Call Waiting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
Accepting a Waiting Call (Camp-On) . . . . . . . . . . . . . . . . . . . . . . . . 53
Preventing and Allowing Call Waiting (Automatic Camp-On). . . . . . 54
Turning the Call Waiting Tone On and Off . . . . . . . . . . . . . . . . . . . . 54
Parking a Call . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
5
Contents
Placing External Calls on Hold . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
Conducting a Conference . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
Ending a Conference (Initiator Only) . . . . . . . . . . . . . . . . . . . . . . . . 58
Activating Tone Dialing/DTMF Suffix-Dialing . . . . . . . . . . . . . . . . . . 59
Recording Calls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60
Transferring a Call after a Speaker Call
(Announcement) in a Group. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61
Trunk Flash . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62
If You Cannot Reach a Destination ... . . . . . . . . . . . . . . . . . . . . . . . . . . 63
Call Waiting (Camp-On) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63
Busy Override - Joining a Call in Progress . . . . . . . . . . . . . . . . . . . . 63
Using Night Answer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64
Saving Functions, Procedures and Appointments.65
Assigning Functions to Keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65
Assigning a Procedure (Operating Steps) to a Key . . . . . . . . . . . . . . . . 69
Appointments Function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71
Saving Appointments. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71
Using Timed Reminders . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72
Displaying and Assigning Call Charges. . . . . . . . . .73
Displaying Call Charges (Not for U.S.) . . . . . . . . . . . . . . . . . . . . . . . . . . 73
Displaying Call Charges for Another Telephone (Not for U.S.) . . . . . . . 74
Dialing with Call Charge Assignment . . . . . . . . . . . . . . . . . . . . . . . . . . 75
Private Sphere/Security . . . . . . . . . . . . . . . . . . . . . . .76
Turning Ringer Cutoff On and Off . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76
Turning Do Not Disturb On and Off. . . . . . . . . . . . . . . . . . . . . . . . . . . . 76
Caller ID Suppression . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77
Monitoring a Room . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78
Trace Call: Identifying Anonymous Callers (Not for U.S.) . . . . . . . . . . . 79
Locking the Telephone to Prevent Unauthorized Use . . . . . . . . . . . . . . 80
Locking Another Telephone to Prevent Unauthorized Use . . . . . . . . . . 81
Saving Your PIN. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82
Using Other Functions. . . . . . . . . . . . . . . . . . . . . . . . .83
Sending a Message . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83
Creating and Sending a Message . . . . . . . . . . . . . . . . . . . . . . . . . . 83
Displaying and Deleting Messages You Have Sent . . . . . . . . . . . . . 84
Answering Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84
Leaving an Advisory Message . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85
Deleting Advisory Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85
Display Number of Waiting Calls and Overload Indication . . . . . . . . . . 86
6
Contents
Using Another Telephone Like Your Own for a Call . . . . . . . . . . . . . . . 86
Using Another Telephone Like your Own for an Extended Period
of Time (Mobility). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87
Fax Details and Message on Answering Machine . . . . . . . . . . . . . . . . 88
Resetting Services and Functions
(System-Wide Cancellation for a Telephone). . . . . . . . . . . . . . . . . . . . . 88
Activating Functions for Another Telephone . . . . . . . . . . . . . . . . . . . . . 89
Using System Functions from the Outside
(DISA: Direct Inward System Access) . . . . . . . . . . . . . . . . . . . . . . . . . . 90
Using functions in ISDN via code dialing (keypad dialing) . . . . . . . . . . . 92
Controlling Connected Computers or Other Programs
and Telephone Data Service
(HiPath 3500/3550/3700/3750/3800 Only). . . . . . . . . . . . . . . . . . . . . . . 93
Communicating with PC Applications over a CSTA Interface . . . . . . . . 94
Controlling Relays (not for HiPath 2000) . . . . . . . . . . . . . . . . . . . . . . . . 95
Sensors (HiPath 3300/3350/3500/3550 Only) . . . . . . . . . . . . . . . . . . . . 95
Radio Paging (Not for U.S.) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 96
Using Other Team Functions. . . . . . . . . . . . . . . . . . .97
Turning Group Call On and Off . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 97
Accepting a Call for Another Member of Your Team . . . . . . . . . . . . . . 99
Activating and Deactivating a Ringing Group. . . . . . . . . . . . . . . . . . . . 100
Uniform Call Distribution (UCD). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 101
Team and Executive/Secretary
Functions With Trunk Keys . . . . . . . . . . . . . . . . . . .103
Using Trunk Keys. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 103
Answering Calls With Trunk Keys . . . . . . . . . . . . . . . . . . . . . . . . . 104
Making Calls with Trunk Keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . 104
Using a Trunk Key to Place a Call on Hold and Retrieve It Again. . 104
Switching Between Phone Calls on Multiple Trunks . . . . . . . . . . . 105
MULAP Conference Release . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 105
Forwarding Calls on Lines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 106
Using DSS Keys. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 108
Using DSS Keys to Answer Calls. . . . . . . . . . . . . . . . . . . . . . . . . . 108
Calling a Team Member Directly . . . . . . . . . . . . . . . . . . . . . . . . . . 108
Transferring a Call in Progress. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 109
Accepting a Call for Another Team Member . . . . . . . . . . . . . . . . . . . . 109
Joining or Leaving a Group Call
(Not for the Executive Telephone in an Executive/Secretary Team) . . 109
Transferring Calls Directly to the Executive
(Only in an Executive/Secretary Group) . . . . . . . . . . . . . . . . . . . . . . . . 110
7
Contents
Testing the Telephone. . . . . . . . . . . . . . . . . . . . . . . .111
Testing the Telephone Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . 111
Checking the Key Assignment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 111
Special Functions in the LAN (PC Network). . . . .112
Leaving a Hunt Group/Group Call . . . . . . . . . . . . . . . . . . . . . . . . . . . . 112
Transferring Call Forwarding . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 113
Using Night Answer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 114
Activating and Deactivating a Ringing Group. . . . . . . . . . . . . . . . . . . . 115
Controlling Relays (not for HiPath 2000) . . . . . . . . . . . . . . . . . . . . . . . 116
Opening the Door . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 117
Different Displays (HiPath 4000 Environment) . . .118
Changing Key Labels. . . . . . . . . . . . . . . . . . . . . . . . .120
Entering Text on the Telephone . . . . . . . . . . . . . . .121
Labeling, Documentation and Accessories . . . . .123
Labeling Key Fields . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 123
Attaching a Station Number Label. . . . . . . . . . . . . . . . . . . . . . . . . . . . 123
Documentation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 123
Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 124
Fixing Problems . . . . . . . . . . . . . . . . . . . . . . . . . . . . .125
Telephone Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 125
Echo Effect . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 125
Troubleshooting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 125
Responding to Error Messages on the Screen . . . . . . . . . . . . . . . . . . 126
Contacts for Resolving Problems . . . . . . . . . . . . . . . . . . . . . . . . . . . . 127
Index. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .128
Overview of Functions/Codes (Alphabetical). . . .133
FCC and Industry Canada Compliance. . . . . . . . . .138
FCC Certification and Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . 138
Equipment Attachment Limitations. . . . . . . . . . . . . . . . . . . . . . . . . . . 140
8
Basic operating instructions
Basic operating instructions
optiPoint 420 advance and
optiPoint self labeling key module control panel
Speaker for open listening
and ring tones
Handset
Key for confirming a function
Backlight graphics
display, 4 lines with
24 chars
Keys for scrolling to functions
Key field –
fixed function keys
Program/Service
Redial
Mailbox
Mute or Internal
Speaker
Key field
freely programmable
keys
optiPoint self labeling
key module
Keypad
Microphone
for speakerphone mode
2
2
–
1
1
:
2
Keys for telephone settings
[1] With automatic key labeling
[2] Cannot be changed on optiPoint 420 advance
9
Basic operating instructions
Step by Step
How to Use these Operating Instruc-
tions
You will find a graphic representation of the steps in logical sequence in the left column. Below is an explanation of the symbols:
n Lift the handset (off-hook).
t Replace the handset (on-hook).
s Conduct a call.
o Enter a telephone number or code.
dd Enter the code.
u or v Press volume controls on the telephone.
Program/Service
Speaker
Start conference?
Display contrast?
> : Search for an option.
Press the key.
Press the illuminated key.
Press the flashing key.
: The option appears on the screen.
Press the
Press the
until the option appears on the screen.
Then press the
: key to confirm your selection.
< > keys,
:
key to confirm your selection
.
10
Step by Step
Basic operating instructions
Displays
Two-line display
1
12:47 FR 9 JUL 04
2
Directory? >
3
4
1
" Brink Sandra
2
Daum Johann
3
Meier Georg
4
Call? >
Line 1 displays situation-specific prompts or confirmation messages.
Line 2 displays functions that you can select by pressing
:. The symbol “>” on the right of this line indicates
that additional options are available; you can scroll to
these using
List display
When list display mode is active, entries are displayed
in the form of a multi-line list. The selected entry is indicated by a square (cursor) at the start of the line.
Cursor indicating the selected entry.
Lines 1 to 3 contain up to three list entries. Use
v
to scroll through the entire list.
Line 4 displays functions that you can operate by press-
ing < > and : (see above).
The following functions are displayed in lists:
• Caller list ! Page 41
(list of unanswered calls)
• Call pickup ! Page 99
(list of users to be picked up)
• Internal directory ! Page 45
(list of internal station numbers and system speeddialing numbers)
• Conference ! Page 57
(list of conference participants)
• LDAP telephone database ! Page 48
(list of LDAP search results)
• Connection costs ! Page 73
(list of toll connections)
< >.
u
and
11
Basic operating instructions
Step by Step
Accessing Functions
For information on displays and how to use lists
displayed ! Page 11.
...
Interactively
You can select some functions while the telephone is
idle, for example:
Forwarding on
> : Use < > to scroll to a function and press : to
execute it.
You can select other functions directly depending on
the situation. Example: you call a number, but the line
is busy:
Callback
Send message
> : Use < > to scroll to a function and press : to
Program/Service
#0=Reset services?
> : Use < > to scroll to a function and press : to
: Press : to confirm.
or
execute it.
...
Via the Program/Service Menu
First press the "Program/Service" key. You then see a list
of selection options, such as: "#0=Reset services"
! Page 88.
Press the key.
execute it.
or
rd Enter the code directly.
The Quick-Reference Operating Instructions ("Overview
of Functions/Codes (Alphabetical)" ! Page 133) contain
a list of codes. However, they are also displayed on
screen along with the corresponding function.
12
...
With Function Keys
If you saved a function on a key ! Page 65, you can ac-
cess it directly as follows:
Press the Mute key to execute the function.
Step by Step
Basic operating instructions
Functions You Can Use
Self Labelling Key Function
Thanks to the Self Labelling Key function, you do not
need to label your telephone's programmable function
keys manually. Depending on how they are programmed, your HiPath automatically assigns a standard
label to your function keys.
However, if you wish, you can also define your own text
labels for the function keys rather than using the standard labels ! Page 120.
Basic and Enhanced Functions
You can use all basic and enhanced communications
platform functions that appear interactively on the
screen, in the Program/Service menu, and when you
press function keys.
Additional Team and Executive/Secretary
Functions
! Page 103f.
To help working and project groups work together more
efficiently, the service personnel can configure a variety
of team functions, depending on your preferences
when working in the team. You can use these team
functions in addition to the basic and enhanced functions.
In addition to call pickup, hunting groups (group call),
and call distribution groups, you can also set up teams
with multiple lines per telephone.
You can tell if a telephone has trunk keys if your station
number and the numbers of your colleagues are programmed on trunk keys. You can access all lines and
can also conduct different calls simultaneously on multiple lines.
Another team function category includes the executive/
secretary
functions, which are configured by the service personnel. You can use executive and secretary functions in
addition to the basic and enhanced functions as well as
other team functions.
13
Basic operating instructions
Step by Step
An executive/secretary telephone has DSS keys for the
executive or secretary, trunk keys for the executive and
secretary, as well as ring transfer keys.
Using the Telephone Efficiently
• You probably have certain colleagues or external parties with whom you talk on the phone especially frequently. To dial these numbers faster and more conveniently, you can save them on keys
(Saving station numbers for repertory dialing on
keys ! Page 29).
• All too often you reach a busy line when dialing a
number. Amid the confusion of your working day,
it’s easy to forget to try the number again later on.
To avoid this, make it a habit to use the "Callback"
! Page 27 function.
Safety Precautions for IP Telephony
Different methods can be implemented to protect an IP
environment from external attacks (denial of service attacks, viruses, etc.) and call monitoring.
There are no special procedures for operating this device. Please contact your service personnel to find out
more about IP telephony security.
14
Step by Step
Making Calls – Basic Functions
Making Calls – Basic Functions
Answering Calls
Special default ring signaling is set for your telephone:
• When you receive an internal call, your telephone
rings once every four seconds (single-tone sequence).
• When you receive an external call, your telephone
rings twice in rapid succession every four seconds
(dual-tone sequence).
• When you receive a call from the entrance telephone,
your telephone rings three times in rapid succession
every four seconds (triple-tone sequence).
• If a call is waiting, you hear a short tone (beep) every
six seconds.
Your service personnel can adjust the ring cadence for external and internal calls for you. In
other words, different ring cadences can be set
for different internal callers.
The number or the name of the caller appears on the
display.
Answering a Call With the Handset
The telephone rings. The caller appears on the screen.
n Lift the handset.
u or v Raise or lower the volume. Keep pressing the key until
the desired volume is set.
Answering a Call with the Speaker
(Speakerphone Mode)
Speaker
u or v Raise or lower the volume. Keep pressing the key until
The telephone rings. The caller appears on the screen.
Press the key. The LED lights up.
Speakerphone mode.
the desired volume is set.
15
Making Calls – Basic Functions
Step by Step
Ending the call:
Speaker
Speaker
Release
Press the key. The LED goes out.
or
Press the key.
Notes on speakerphone mode:
• Tell the other party that you are using speakerphone
mode.
• The speakerphone works bests at a low receiving
volume.
• The ideal distance between the user and the telephone set in speakerphone mode is about 50 cm
(approx. 20 inches).
Switching to Speakerphone Mode
Precondition: You are conducting a call with the handset.
and
t Hold down the key and replace the handset.
(in the U.S.: press the key once and replace the handset). Then release the key and continue the call.
Switching to the Handset
Precondition: You are engaged in a call in speakerphone mode.
n and s Lift the handset. Continue the call.
16
Step by Step
Making Calls – Basic Functions
Open Listening in the Room During a
Call
You can let other people in the room join in on the call.
Let the other party know that you have turned on the
speaker.
Precondition: You are conducting a call with the handset.
Activating ring transfer:
Speaker
Speaker
Press the key. The LED lights up.
Deactivating this function:
Press the key. The LED goes out.
17
Making Calls – Basic Functions
Step by Step
Making Calls
Off-Hook Dialing
n Lift the handset.
o Internal calls: Enter the station number.
External calls: Enter the external code and the station
number.
The called party does not answer or is busy:
t Replace the handset.
On-Hook Dialing
Speaker
o Internal calls: Enter the station number.
External calls: Enter the external code and the station
number.
The other party answers with speaker:
n Lift the handset.
or On-hook: Use speakerphone mode .
The called party does not answer or is busy:
Press the key. The LED goes out.
Your system may also be programmed so that
you have to press the Internal key before you dial
an internal number.
To call an external party, you have to enter an external code before dialing the party’s telephone
number (Prime Line is not active; contact your
service personnel).
Release
18
Ending the call
t Replace the handset.
or
Press the key.
Step by Step
Making Calls – Basic Functions
Redialing a Number
The last three external telephone numbers dialed are
stored automatically.
You can redial them simply by pressing a key.
The station number appears on your screen for two seconds and is then dialed.
Redial
Press the key once to dial the number last dialed.
Press the key twice to dial the next to the last number
dialed.
Press the key three times to dial the third-to-the-last
number dialed.
Displaying and dialing saved station numbers
Next?
Redial
: Press the "OK" dialog key within two seconds to confirm
Press the key.
your choice.
Next?
: The next stored number is displayed. Press the "OK" di-
alog key to confirm four selection.
Call?
> : Select and confirm.
If this feature is configured (contact your service
personnel), account codes entered are also
saved ! Page 75.
19
Making Calls – Basic Functions
Step by Step
Turning the Microphone On and Off
To prevent the other party from listening in while you
consult with someone in your office, you can temporarily switch off the handset microphone or the handsfree
microphone. You can also switch on the handsfree microphone to answer an announcement via the telephone speaker (speaker call, ! Page 36).
Precondition: You are conducting a call. The microphone is switched on.
Mute
Press the key. The LED lights up.
or
Mute
Press the illuminated key. The LED goes out.
or
Mute on?
> : Select and confirm.
or
Mute off?
> :
or
Program/Service
Press the key. The LED lights up.
qif or rif Enter the code for "on" or "off".
20
Step by Step
Making Calls – Basic Functions
Calling a Second Party
(Consultation Hold)
You can call a second party while engaged in a call. The
first party is placed on hold.
US: Consultation?
UK: Enquiry?
:
:
Confirm.
o Call the second party.
Return to the first party:
Return to held call?
Quit and return?
Program/Service
: Confirm.
or
:
or
qd Press the key. The LED lights up. Enter the code. The
LED goes out.
Switching to the Party on Hold (Toggle)
Toggle/Connect?
> : Select and confirm.
or
Program/Service
qf Press the key. The LED lights up. Enter the code. The
LED goes out.
Combine the calling parties into a three-party conference
Conference?
> : Select and confirm.
Program/Service
Transfer?
> : Select and confirm.
or
qg Press the key. The LED lights up. Enter the code. The
LED goes out.
Connecting the other parties to each other
21
Making Calls – Basic Functions
Step by Step
Transferring a Call
If the person you are speaking to wants to talk to
another colleague of yours, you can transfer the call that
colleague.
US: Consultation?
UK: Enquiry?
:
:
Confirm.
o Enter the number of the party to which you want to
transfer the call.
s Announce the call, if necessary.
t Replace the handset.
or
Transfer?
> : Select and confirm
1
.
22
[1] ”Different Displays (HiPath 4000 Environment)” ! Page 118)
Step by Step
Call Forwarding
Using Variable Call Forwarding
You can immediately forward internal or external calls to
different internal or external telephones (destinations).
(External destinations require special configuration in
the system.)
Special features must be taken into consideration
if your telephone operates with HiPath 5000 (system networking via PC network) ! Page 113!
Forwarding on?
> : Select and confirm.
or
Making Calls – Basic Functions
qe Enter the code.
1=all calls?
2=external calls only?
> :
3=internal calls only?
> :
: Select and confirm.
or
or
or
e or f or g Enter the code.
o Enter the number of the telephone that is ringing.
US: Save?
UK: Save entry?
Forwarding off?
> : Select and confirm.
:
:
or
Confirm.
Deactivating call forwarding:
re Enter the code.
When call forwarding is active, a special dial tone
sounds when you lift the handset.
If DID DTMF is active (contact your service personnel), you can also forward calls to this destination. Destinations: fax = 870, DID = 871,
fax DID = 872.
If you are a call forwarding destination, your display will show the station number or the name of
the originator on the upper line and that of the
caller on the lower line.
23
Making Calls – Basic Functions
Step by Step
Using Call Forwarding No Reply (CFNR)
Calls that are not answered after three rings (=default,
can be adjusted by service personnel) or that are received while another call is ongoing can be automatically forwarded to a specified telephone.
Program/Service
More features?
> : Select and confirm.
*495=CFNR on?
> : Select and confirm.
Press the key. The LED lights up.
or
qhmi Enter the code.
o Enter the destination number.
• Enter the internal station number for internal destinations
• Enter the external code and the external station
number for external destinations
Save entry?
: Confirm.
Deactivating Call Forwarding No Reply:
Program/Service
More features?
> : Select and confirm.
#495=CFNR off?
> : Select and confirm.
Press the key. The LED lights up.
or
rhmi Enter the code.
Delete?
24
: Confirm.
If CFNR is enabled, the following briefly appears
on the display when you replace the handset:
„CFNR to: ...“.
Step by Step
Call Forwarding in the Carrier Network
and Forwarding Multiple Subscriber Num-
bers (MSN) (Not for U.S.)
If this function has been configured (contact your service personnel), you can forward calls to your assigned
multiple subscriber number (MSN) (DID number) directly within the carrier network.
For example, you can forward your phone line to your
home phone after business hours.
Trunk FWD on?
> : Select and confirm.
or
qjh Enter the code.
Making Calls – Basic Functions
1=immediate?
2=on no answer?
> :
3= on busy?
> :
: Select and confirm the line type you wish to use.
or
or
or
e or f or g Enter the code.
o Enter your DID number.
o Enter the destination number (without the external
code).
Save?
Forwarding - trunk off
> : Select and confirm.
: Confirm.
Deactivating call forwarding:
or
rjh Enter the code.
e or f or g Enter the activated call forwarding type.
: Confirm the displayed call forwarding type.
or
o Enter your DID number.
25
Making Calls – Basic Functions
Step by Step
Call Forwarding in the Event of a Telephone
Malfunction
If this feature is configured (ask the service personnel),
you can define an internal or external call forwarding
destination that becomes effective when your telephone is not working.
Program/Service
*9411=CFSS on
> : Select and confirm.
Press the key. The LED lights up.
or
qmhee Enter the code.
o Enter the station number of the destination.
US: Save entry?
UK: Save?
Program/Service
#9411=CFSS off
> : Select and confirm.
: Confirm.
:
Deactivating call forwarding/deleting a destination:
Press the key. The LED lights up.
or
rmhee Enter the code.
Delete?
Delete?
> : Select and confirm to deactivate call forwarding without
Program/Service
qmhee Enter the code.
US: Change?
> :
UK: Change entry?
> :
US: Save entry?
UK: Save?
26
:
: Confirm to deactivate call forwarding and delete the for-
warding destination.
or
deleting the forwarding destination.
Changing the call forwarding destination (if forwarding is active):
Press the key. The LED lights up.
Confirm.
o Change the station number of the destination.
:
Confirm.
Step by Step
Making Calls – Basic Functions
Using Callback
If a user is busy or is not answering, you can store an
automatic callback. This feature saves you from having
to make repeated attempts to reach the user.
You receive a callback,
• When the other party is no longer busy
• When the user who did not answer has conducted
another call.
Storing a Callback
Precondition: You have reached a busy line or no one
answers.
US: Callback
UK: Set Callback
:
:
or
Confirm.
qil Enter the code.
Answering a Callback
Precondition: A callback was saved. Your telephone
rings. "Callback: ..." appears on the display.
n Lift the handset.
or
Speaker
Press the key. The LED lights up.
You hear a ring tone.
Checking and Canceling a Saved Callback
View callbacks?
> : Select and confirm
or
1
.
ril Enter the code.
US: Next callback?
> :
UK: Display next?
> :
Select the displayed function and press the "OK" dialog
key to display additional entries.
[1] ”Different Displays (HiPath 4000 Environment)” ! Page 118)
27
Making Calls – Basic Functions
Step by Step
Deleting a displayed entry:
Delete?
US: Exit?
> :
UK: End?
> :
: Press the "OK" dialog key to confirm your selection.
or
Program/Service
or
Speaker
Ending callback display:
Select and confirm.
Press the key. The LED goes out.
Press the key. The LED goes out.
28
Step by Step
Making Calls – Basic Functions
Saving Repertory Dial i ng Numbers on
a Key
You can save frequently-dialed station numbers on programmable keys that are unassigned by default.
External and internal station numbers, as well as functions/procedures (comprising several operating steps)
can be stored on these keys ! Page 65.
In addition, the keys can be programmed on two separate levels if you have configured a key as the "switching" key (Shift key ! Page 65).
Depending on the key assignment and programming of
your HiPath system ("Extended Key Functionality"; refer
to relevant service personnel), dual-level key assignment permits several assignment combinations.
Corresponding displays guide you through this process
! Page 126.
If you save internal station numbers, you can choose
whether to save an LED display for the key (=Save with
LED) or not (=Save without LED).
The LED display indicates the various states
(! Page 67, ! Page 108).
Program/Service
> : Select and confirm.
91=Prog. feature key?
*
Press the key. The LED lights up.
or
qme Enter the code.
Program/Service
If applicable
+=Next layer?
> : Make a selection and confirm to save the station num-
or
US: Change key?
UK: Change feature?
Repdial key?
:
:
: Confirm.
Press the key. If the key is already in use, its assignment
appears also on the screen.
ber on the second level.
u
Confirm.
o Enter the station number.
29
Making Calls – Basic Functions
Step by Step
If you make a mistake:
Previous?
> : Select and confirm. This deletes all digits entered.
The system telephone automatically recognizes if you
want to save an internal or an external station number.
The options "Save without LED" or "Save with LED" are
only available for internal station numbers.
Save with LED?
: Confirm.
or
Save without LED?
> : Select and confirm to save the repdial key without LED
display.
If applicable
Key label?
> : Select and confirm to update automatic key labeling.
For more information, see ! Page 120.
US: Exit?
UK: End?
:
:
Confirm.
or
US: Another key?
> :
UK: Program another key?
> :
Select and confirm.
or
US: Clear key?
> :
UK: Delete feature?
:
>
Select and confirm.
Simply press the key to dial a stored telephone
number ! Page 31.
You can do this while a call is in progress.
30
For information on display messages when saving station numbers ! Page 126.
Loading...