Showtec Galaxy 360 XL User manual
Galaxy 360 V1
Highlite International B.V. – Vestastraat 2 – 6468 EX – Kerkrade – the Netherlands
Ordercode: 45054
MANUAL
ENGLISH
Ordercode: 45054
Galaxy 360
Table of contents
Warning ............................................................................................................................................................................... 3
Safety Instructions ......................................................................................................................................................... 3
Operating Determinations .......................................................................................................................................... 5
Rigging ............................................................................................................................................................................ 5
Connection with the mains ......................................................................................................................................... 6
Return Procedure .......................................................................................................................................................... 6
Claims .............................................................................................................................................................................. 6
Description of the device ................................................................................................................................................. 7
Frontside .......................................................................................................................................................................... 7
Backside ......................................................................................................................................................................... 8
Installation ........................................................................................................................................................................... 8
Set Up and Operation ....................................................................................................................................................... 8
Control Modes ............................................................................................................................................................... 9
One Galaxy 360 (Built-in programs and Manual) ................................................................................................ 9
One Galaxy 360 (Sound-control) ............................................................................................................................ 9
Multiple Galaxys 360 (Master/Slave control) ........................................................................................................ 9
Multiple Galaxys 360 (DMX512 Mode) .................................................................................................................10
Fixture Linking ...............................................................................................................................................................11
Data Cabling ...............................................................................................................................................................11
Control Panel ...............................................................................................................................................................12
DMX Control Mode .....................................................................................................................................................12
DMX Addressing ..........................................................................................................................................................12
Menu Overview ...........................................................................................................................................................13
Main Menu Options ....................................................................................................................................................14
1. DMX-512 ................................................................................................................................................................14
2. Channel Mode .....................................................................................................................................................14
3. Run Mode ..............................................................................................................................................................15
3.1. DMX Mode .........................................................................................................................................................15
3.2. Master Mode .....................................................................................................................................................15
3.3. Slave Mode........................................................................................................................................................15
3.4. Sound Mode ......................................................................................................................................................15
3.5. Manual Mode ...................................................................................................................................................16
4. Functions ...............................................................................................................................................................16
4.1. Pan Invert ...........................................................................................................................................................16
4.2. Tilt Invert ..............................................................................................................................................................17
4.3. Dimmer Curve ...................................................................................................................................................17
4.4. DMX Fail ..............................................................................................................................................................17
4.5. Display ................................................................................................................................................................17
4.6. Back Light ...........................................................................................................................................................18
4.7. Reset ...................................................................................................................................................................18
4.8. Factory Sets .......................................................................................................................................................18
4.9. Auto Test .............................................................................................................................................................18
5. Version ...................................................................................................................................................................18
DMX Channels .............................................................................................................................................................19
10 Channels ..............................................................................................................................................................19
18 Channels ..............................................................................................................................................................21
66 Channels ..............................................................................................................................................................24
Maintenance ....................................................................................................................................................................30
Replacing a Fuse ........................................................................................................................................................30
1
Ordercode: 45054
Galaxy 360
Troubleshooting ...............................................................................................................................................................30
No Light .........................................................................................................................................................................30
No Response to DMX ..................................................................................................................................................31
Product Specifications ....................................................................................................................................................32
Dimensions ........................................................................................................................................................................33
Notes ..................................................................................................................................................................................34
2
Ordercode: 45054
Galaxy 360
Your shipment includes:
Showtec Galaxy 360
1 mounting bracket with quick locks
Pro power connector to Schuko cable
(length 1,5 m)
Safety cable
User manual
Warning
Unpacking Instructions
Immediately upon receiving this product, carefully unpack the carton and check the contents to ensure
that all parts are present, and have been received in good condition. Notify the dealer immediately and
retain packing material for inspection if any parts appear to be damaged from shipping or the carton
itself shows signs of mishandling. Save the carton and all packing materials. In the event that the fixture
must be returned to the factory, it is important that the fixture be returned in the original factory box and
packing.
LED Expected Lifespan
LEDs gradually decline in brightness over time. HEAT is the dominant factor that leads to the acceleration
of this decline. Packaged in clusters, LEDs exhibit higher operating temperatures than in ideal or singular
optimum conditions. For this reason when all color LEDs are used at their fullest intensity, life of the LEDs is
significantly reduced. If improving the lifespan is of higher priority, place care in providing for lower
operational temperatures. This may include climatic-environmental and the reduction of overall
projection intensity.
Safety Instructions
Every person involved with the installation, operation and maintenance of this device has to:
be qualified
follow the instructions of this manual
Before your initial start-up, please make sure that there is no damage caused by transportation. Should
there be any, consult your dealer and do not use the device.
To maintain perfect condition and to ensure a safe operation, it is absolutely necessary for the user to
follow the safety instructions and warning notes written in this manual.
Please consider that damages caused by manual modifications to the device are not subject to
warranty. This device contains no user-serviceable parts. Refer servicing to qualified technicians only.
3
Ordercode: 45054
Galaxy 360
IMPORTANT:
The manufacturer will not accept liability for any resulting damages caused by the non-observance of
this manual or any unauthorized modification to the device.
Never let the power cord come into contact with other cables! Handle the power cord and all
connections with the mains with particular caution!
Never remove warning or informative labels from the unit.
Never use anything to cover the ground contact.
Never lift the fixture holding it by the projector-head, as the mechanics may be damaged. Always
hold the fixture by the transport handles.
Never place any material over the lens.
Never look directly into the light source.
Never leave any cables lying around.
Do not insert objects into air vents.
Do not connect this device to a dimmerpack.
Do not switch the device on and off in short intervals, as this would reduce the device’s lifespan.
Do not touch the device’s housing bare-handed during its operation. Allow the fixture to cool for at
least 5 minutes before handling.
Do not shake the device. Avoid brute force when installing or operating the device.
Only use device indoors, avoid contact with water or other liquids.
Only operate the fixture after having checked if the housing is firmly closed and all screws are tightly
fastened.
Only operate the device after having familiarized with its functions.
Avoid flames and do not put close to flammable liquids or gases.
Always keep case closed while operating.
Always allow free air space of at least 50 cm around the unit for ventilation.
Always disconnect power from the mains, when device is not used or before cleaning! Only handle
the power cord by the plug. Never pull out the plug by tugging the power cord.
Make sure that the device is not exposed to extreme heat, moisture or dust.
Make sure that the available voltage is not higher than stated on the rear panel.
Make sure that the power cord is never crimped or damaged. Check the device and the power
cord from time to time.
If the lens is obviously damaged, it has to be replaced to prevent its functions from being impaired,
due to cracks or deep scratches.
If device was dropped or struck, disconnect mains power supply immediately. Have a qualified
engineer inspect for safety before operating.
If the device has been exposed to drastic temperature fluctuation (e.g. after transportation), do not
switch it on immediately. The arising condensation water might damage your device. Leave the
device switched off until it has reached room temperature.
If your Showtec device fails to work properly, discontinue use immediately. Pack the unit securely
(preferably in the original packing material), and return it to your Showtec dealer for service.
For adult use only. Device must be installed out of reach of children. Never leave the unit running
unattended.
Never attempt to bypass the thermostatic switch or fuses.
For replacement, use fuses of same type and rating only.
The user is responsible for correct positioning and operating of the Galaxy 360. The manufacturer will
not accept liability for damages caused by the misuse or incorrect installation of this device.
This device falls under protection class I. Therefore it is essential to connect the yellow/green
conductor to earth.
Repairs, servicing and electrical connection must be carried out by a qualified technician.
WARRANTY: Till one year after date of purchase.
4
Ordercode: 45054
Galaxy 360
Operating Determinations
This device is not designed for permanent operation. Regular operation breaks will ensure that the
device will serve you for a long time without defects.
The minimum distance between light-output and the illuminated surface must be bigger than 1
meter.
The maximum ambient temperature ta = 40°C must never be exceeded.
The relative humidity must not exceed 50 % with an ambient temperature of 40° C.
If this device is operated in any other way than the one described in this manual, the product may
suffer damages and the warranty becomes void.
Any other operation may lead to dangers like short-circuit, burns, electric shock, crash etc.
You endanger your own safety and the safety of others!
Rigging
Please follow the European and national guidelines concerning rigging, trussing and all
other safety issues.
Do not attempt the installation yourself!
Always let the installation be carried out by an authorized dealer!
Procedure:
If the Galaxy 360 is lowered from the ceiling or high joists, professional trussing systems have to be
used.
Use a clamp to mount the Galaxy 360, with the mounting bracket, to the trussing system.
The Galaxy 360 must never be fixed swinging freely in the room.
The installation must always be secured with a safety attachment, e.g. an appropriate safety net or
safety cable.
When rigging, derigging or servicing the Galaxy 360, always make sure, that the area below the
installation site is secured and that there are not any unauthorized people around.
The Galaxy 360 can be placed on a flat stage floor or mounted to any kind of truss by a clamp.
5
Ordercode: 45054
Galaxy 360
International
EU Cable
UK Cable
US Cable
Pin
L
BROWN
RED
YELLOW/COPPER
PHASE
N
BLUE
BLACK
SILVER
NEUTRAL
YELLOW/GREEN
GREEN
GREEN
PROTECTIVE GROUND
Return Procedure
Improper installation can cause serious injuries and/or damage of property!
Connection with the mains
Connect the device to the mains with the power plug.
Always check if the right color cable is connected to the right place.
Make sure that the device is always connected properly to the earth!
Improper installation can cause serious damage to people and property!
Returned merchandise must be sent prepaid and in the original packing, call tags will not be issued.
Package must be clearly labeled with a Return Authorization Number (RMA number). Products returned
without an RMA number will be refused. Highlite will not accept the returned goods or any responsibility.
Call Highlite 0031-455667723 or mail aftersales@highlite.nl and request an RMA prior to shipping the fixture.
Be prepared to provide the model number, serial number and a brief description of the cause of the
return. Be sure to properly pack fixture as any shipping damage resulting from inadequate packaging is
the customer’s responsibility. Highlite reserves the right to use its own discretion to repair or replace
product(s). As a suggestion, proper UPS packing or double-boxing is always a safe method to use.
Note: If you are given an RMA number, please include the following information on a piece of paper
inside the box:
01) Your name.
02) Your address.
03) Your phone number.
04) A brief description of the symptoms.
Claims
The client has the obligation to check the delivered goods immediately upon delivery for any shortcomings and/or visible defects, or perform this check after our announcement that the goods are at their
disposal. Damage incurred in shipping is the responsibility of the shipper; therefore the damage must be
reported to the carrier upon receipt of merchandise.
It is the customer's responsibility to notify and submit claims with the shipper in the event that the fixture is
damaged due to shipping. Transportation damage has to be reported to us within one day after receipt
of the delivery.
Any return shipment has to be made post-paid at all times. Return shipments must be accompanied with
a letter defining the reason for return shipment. Non-prepaid return shipments will be refused, unless
agreed otherwise in writing.
Complaints against us must be made known in writing or by fax within 10 working days after receipt of the
invoice. After this period, complaints will not be handled anymore.
Complaints will only be considered if the client has so far complied with all parts of the agreement,
regardless of the agreement of which the obligation is resulting.
6
Ordercode: 45054
Galaxy 360
Fig. 01
Description of the device
Features
The Showtec Galaxy 360 is a moving head with high output and great effects.
Input voltage: 100~240V AC
Power consumption: 190W
Light source: 12 x 9W RGBW LED
Channels: 10, 18, 66 channels
Beam Angle: 4°
Dimmer: 0-100%
Strobe: 0-20Hz
Dimmer curves: Linear, Square, I-Square, S curve
Pan: 0-540° & continuous
Ball: 0-360° & continuous
Pan/Tilt resolution: 16 bit
Onboard: Display including gravity sensor
Control mode: DMX, Auto, Manual, Sound, Master/Slave
Data connections: 3-pin/5-pin XLR IN/OUT
Power connections: Pro Power connector IN/OUT
Housing: Black metal & flame-retardant plastic
Fuse: 3A/250V
Dimensions: 335 x 145 x 395 mm (LxWxH)
Weight: 7,2 kg
Frontside
01) Lens
02) LCD display + menu buttons
03) Menu control
7
Ordercode: 45054
Galaxy 360
Fig. 02
Backside
04) 3-pin DMX signal connector IN
05) 3-pin DMX signal connector OUT
06) 5-pin DMX signal connector OUT
07) 5-pin DMX signal connector IN
08) Pro Power connector 100-240V IN
09) Pro Power connector 100-240V OUT
10) Ground/earth connection
11) Power switch ON/OFF
12) Fuse 3A/250V
Installation
Remove all packing materials from the Galaxy 360.
Check that all foam and plastic padding is removed. Connect all cables.
Do not supply power before the whole system is set up and connected properly.
Always disconnect from electric mains power supply before cleaning or servicing.
Damages caused by non-observance are not subject to warranty.
Set Up and Operation
Follow the directions below, as they pertain to your preferred operation mode.
Before plugging the unit in, always make sure that the power supply matches the product specification
voltage. Do not attempt to operate a 120V specification product on 230V power, or vice versa.
Connect the device to the main power supply.
8
Ordercode: 45054
Galaxy 360
There are 5 modes:
Built-in programs (Master mode)
Sound-controlled
Manual
Master/Slave
DMX-512 (10CH, 18CH, 66CH)
The pins:
1. Earth
2. Signal (-)
3. Signal (+)
Fig. 03
Control Modes
One Galaxy 360 (Built-in programs and Manual)
01) Fasten the effect light onto firm trussing. Leave at least 0,5 meter on all sides for air circulation.
02) Always use a safety cable (ordercode 70140 / 70141).
03) Plug the end of the electric mains power cord into a proper electric power supply socket.
04) When the Galaxy 360 is not connected by a DMX cable, it functions as a stand-alone device.
Please see pages 15 and 16 for more information about the Built-in programs (Master mode) and
Manual mode.
One Galaxy 360 (Sound-control)
01) Fasten the effect light onto firm trussing. Leave at least 0,5 meter on all sides for air circulation.
02) Always use a safety cable (ordercode 70140 / 70141).
03) Plug the end of the electric mains power cord into a proper electric power supply socket.
04) Turn on the music. If the device is set to sound-control, then the Galaxy 360 will react to the beat of
the music. Please see page 15 for more information about the sound-control options.
Multiple Galaxys 360 (Master/Slave control)
01) Fasten the effect light onto firm trussing. Leave at least 0,5 meter on all sides for air circulation.
02) Always use a safety cable (ordercode 70140 / 70141).
03) Use a 3-pin/5-pin XLR cable to connect the Galaxy 360 and other devices.
04) Link the units as shown in (Fig. 03), connect a DMX signal cable from the first unit's DMX "out" socket to
the second unit's "in" socket. Repeat this process to link the second and third units. You can use the
same functions on the master device as described on pages 15 and 16 (Built-in programs, Manual
and Sound-control). This means you can set your desired operation mode on the master device and
all slave devices will react the same as the master device.
Multiple Galaxys 360 (Master/Slave control)
9
Ordercode: 45054
Galaxy 360
Fig. 04
Multiple Galaxys 360 (DMX512 Mode)
01) Fasten the effect light onto firm trussing. Leave at least 0,5 meter on all sides for air circulation.
02) Always use a safety cable (ordercode 70140 / 70141).
03) Plug the end of the electric mains power cord into a proper electric power supply socket.
04) Use a 3-pin/5-pin XLR cable to connect the Galaxy and other devices.
05) Link the units as shown in (Fig. 04), Connect a DMX signal cable from the first unit's DMX "out" socket
to the second unit's "in" socket. Repeat this process to link the second and third units.
06) Supply electric power: Plug electric mains power cords into each unit's Pro Power socket, then plug
the other end of the mains power cord into proper electric power supply sockets, starting with the
first unit. Do not supply power before the whole system is set up and connected properly.
Multiple Galaxys 360 DMX Set Up
10
Note: Link all cables before connecting electric power!
Loading...