Shop fox W1685, W1666 User Manual

MODEL W1666/W1685 

DUST COLLECTORS

OWNER'S MANUAL

Phone: [phone] • Online Technical Support: [e-mail]

COPYRIGHT © JUNE, 2000 BY WOODSTOCK INTERNATIONAL, INC., REVISED APRIL, 2015 (ST)

WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE OR FORM WITHOUT

#6941CR  Printed in China

(FOR MODELS MANUFACTURED SINCE 02/15)

THE WRITTEN APPROVAL OF WOODSTOCK INTERNATIONAL, INC.

V4.04.15

This manual provides critical safety instructions on the proper setup,
operation, maintenance, and service of this machine/tool. Save this
document, refer to it often, and use it to instruct other operators.

Failure to read, understand and follow the instructions in this manual
may result in fire or serious personal injury—including amputation,
electrocution, or death.

The owner of this machine/tool is solely responsible for its safe use.
This responsibility includes but is not limited to proper installation in
a safe environment, personnel training and usage authorization,
proper inspection and maintenance, manual availability and compre­hension, application of safety devices, cutting/sanding/grinding tool
integrity, and the usage of personal protective equipment.

The manufacturer will not be held liable for injury or property
damage from negligence, improper training, machine modifications or
misuse.

Some dust created by power sanding, sawing, grinding, drilling, and
other construction activities contains chemicals known to the State of
California to cause cancer, birth defects or other reproductive harm.
Some examples of these chemicals are:

• Lead from lead-based paints.

• Crystalline silica from bricks, cement and other masonry products.

• Arsenic and chromium from chemically-treated lumber.

Your risk from these exposures varies, depending on how often you
do this type of work. To reduce your exposure to these chemicals:
Work in a well ventilated area, and work with approved safety equip­ment, such as those dust masks that are specially designed to filter
out microscopic particles.

Contents

INTRODUCTION .....................................2

Woodstock Technical Support .................. 2

W1666 Machine Specification ................. 3

W1685 Machine Specification ................. 5

SAFETY ............................................... 7

Standard Machinery Safety Instructions ...... 7

Additional Safety for Dust Collectors ......... 9

ELECTRICAL ....................................... 10

Circuit Requirements .......................... 10

Grounding Requirements ...................... 11

Extension Cords ................................ 11

SETUP .............................................. 12

Unpacking ....................................... 12

Inventory ........................................ 12

Assembly ......................................... 13

Test Run .......................................... 18

DESIGNING THE SYSTEM ........................ 19

General .......................................... 19

Duct Material ................................... 19

System Grounding .............................. 22

System Design .................................. 23

OPERATIONS....................................... 29

General .......................................... 29

Disabling Switch ................................ 29

Machine Storage ................................ 29

ACCESSORIES ...................................... 30

MAINTENANCE .................................... 32

General .......................................... 32

Lubrication ...................................... 32

Bag Cleaning .................................... 32

Replacing Bags .................................. 33

SERVICE ............................................ 34

Troubleshooting ................................. 34

Electrical Safety Instructions ................. 35

Wiring Diagrams ................................ 36

PARTS .............................................. 37

WARRANTY ........................................ 41

SAFETYINTRODUCTION

SET UPELECTRICAL MAINTENANCE

OPERATIONS

USE THE QUICK GUIDE PAGE LABELS TO SEARCH OUT INFORMATION FAST!

SERVICE PART S

Model W1666/W1685 (For Machines Mfd. Since 2/15)

INTRODUCTION

INTRODUCTION

Woodstock Technical Support

Woodstock International, Inc. is committed to customer satisfaction. Our intent with this manual is to
include the basic information for safety, setup, operation, maintenance, and service of this product.

In the event that questions arise about your machine, please contact Woodstock International Technical
Support at [phone] or send e-mail to: [e-mail]. Our knowledgeable staff will
help you troubleshoot problems or process warranty claims.

If you need the latest edition of this manual, you can download it from http://www.shopfox.biz.
If you have comments about this manual, please contact us at:

Woodstock International, Inc.

Attn: Technical Documentation Manager

P.O. Box 2309

Bellingham, WA 98227

Email: [e-mail]

-2-

Model W1666/W1685 (For Machines Mfd. Since 2/15)

MODEL W1666

SHOP FOX® 2 HP DUST COLLECTOR

Product Dimensions

Weight........................................................................................................... 92 lbs.

Width (side-to-side) x Depth (front-to-back) x Height.............................. 33-1/2 x 21-1/2 x 78 in.

Footprint (Length x Width).................................................................... 33-1/2 x 21-1/2 in.

Shipping Dimensions

Type.................................................................................................... Cardboard Box

Content........................................................................................................ Machine

Weight.......................................................................................................... 108 lbs.

Length x Width x Height........................................................................... 36 x 23 x 23 in.

Must Ship Upright.................................................................................................. Yes

INTRODUCTION

Electrical

Power Requirement.................................................................... 220V, Single-Phase, 60 Hz

Prewired Voltage................................................................................................. 220V

Full-Load Current Rating......................................................................................... 12A

Minimum Circuit Size............................................................................................. 15A

Connection Type......................................................................................... Cord & Plug

Power Cord Included.............................................................................................. Yes

Power Cord Length.............................................................................................. 10 ft.

Power Cord Gauge............................................................................................ 14 AWG

Plug Included........................................................................................................ No

Recommended Plug Type........................................................................................ 6-15

Switch Type............................................................ Paddle Safety Switch w/Removable Key

Motors

Main

Type......................................................................... TEFC Capacitor-Start Induction

Horsepower................................................................................................. 2 HP

Phase.............................................................................................. Single-Phase

Amps.......................................................................................................... 12A

Speed.................................................................................................. 3450 RPM

Power Transfer ................................................................................... Direct Drive

Bearings................................................................. Sealed & Permanently Lubricated

-3-

INTRODUCTION

Model W1666/W1685 (For Machines Mfd. Since 2/15)

Main Specifications

Operation

Dust Collector Type.............................................................................. Single-Stage

Approved Dust Types.................................................................................... Wood

Filter Type................................................................................................... Bag

Airflow Capacity..................................................................................... 1550 CFM

Max Static Pressure (at 0 CFM)...................................................................... 12.3 in.

Main Inlet Size............................................................................................. 6 in.

Inlet Adapter Included..................................................................................... Yes

Number of Adapter Inlets.................................................................................... 2

Adapter Inlet Size......................................................................................... 4 in.

Machine Collection Capacity At One Time................................................................. 3

Maximum Material Collection Capacity......................................................... 5.4 cu. ft.

Filtration Rating.................................................................................... 2.5 Micron

Bag Information

Number of Upper Bags........................................................................................ 1

Number of Lower Bags........................................................................................ 1

Upper Bag Diameter..................................................................................... 19 in.

Upper Bag Length........................................................................................ 33 in.

Lower Bag Diameter..................................................................................... 19 in.

Lower Bag Length........................................................................................ 33 in.

Impeller Information

Impeller Type........................................................................................ Radial Fin

Impeller Size.............................................................................................. 12 in.

Impeller Blade Thickness............................................................................. 3/32 in.

Construction

Upper Bag................................................................................................. Fabric

Lower Bag................................................................................................ Plastic

Base............................................................................. Steel Sheet Metal w/Casters

Caster............................................................................................... Four Plastic

Impeller.................................................................................................... Steel

Paint Type/Finish............................................................................. Powder Coated

Blower Housing............................................................................. Steel Sheet Metal

Body......................................................................................... Steel Sheet Metal

Other

Country of Origin ............................................................................................... China

Warranty ....................................................................................................... 2 Years

Approximate Assembly & Setup Time ................................................................. 45 Minutes

Serial Number Location .................................................................................... ID Label

ISO 9001 Factory .................................................................................................. Yes

CSA, ETL, or UL Certified/Listed ................................................................................ No

Features

Powder-Coated Finish
Quick Release Band Clamp
Includes Steel Base with Casters

-4-

Model W1666/W1685 (For Machines Mfd. Since 2/15)

MODEL W1685

SHOP FOX® 1-1/2 HP DUST COLLECTOR

Product Dimensions

Weight........................................................................................................... 90 lbs.

Width (side-to-side) x Depth (front-to-back) x Height.............................. 33-1/2 x 21-1/4 x 78 in.

Footprint (Length x Width).................................................................... 33-1/2 x 21-1/4 in.

Shipping Dimensions

Type.................................................................................................... Cardboard Box

Content........................................................................................................ Machine

Weight.......................................................................................................... 107 lbs.

Length x Width x Height........................................................................... 36 x 23 x 23 in.

Must Ship Upright.................................................................................................. Yes

INTRODUCTION

Electrical

Power Requirement.................................................................... 110V, Single-Phase, 60 Hz

Prewired Voltage................................................................................................. 110V

Full-Load Current Rating......................................................................................... 16A

Minimum Circuit Size............................................................................................. 20A

Connection Type......................................................................................... Cord & Plug

Power Cord Included.............................................................................................. Yes

Power Cord Length............................................................................................... 6 ft.

Power Cord Gauge............................................................................................ 14 AWG

Plug Included....................................................................................................... Yes

Recommended Plug Type........................................................................................ 5-15

Switch Type.............................................................................................. Push Button

Motors

Main

Type......................................................................... TEFC Capacitor-Start Induction

Horsepower.............................................................................................. 1.5 HP

Phase.............................................................................................. Single-Phase

Amps.......................................................................................................... 16A

Speed.................................................................................................. 3450 RPM

Power Transfer ................................................................................... Direct Drive

Bearings................................................................. Sealed & Permanently Lubricated

-5-

INTRODUCTION

Model W1666/W1685 (For Machines Mfd. Since 2/15)

Main Specifications

Operation

Dust Collector Type.............................................................................. Single-Stage

Approved Dust Types.................................................................................... Wood

Filter Type................................................................................................... Bag

Airflow Capacity..................................................................................... 1280 CFM

Max Static Pressure (at 0 CFM)...................................................................... 10.1 in.

Main Inlet Size............................................................................................. 6 in.

Inlet Adapter Included..................................................................................... Yes

Number of Adapter Inlets.................................................................................... 2

Adapter Inlet Size......................................................................................... 4 in.

Machine Collection Capacity At One Time................................................................. 2

Maximum Material Collection Capacity......................................................... 5.4 cu. ft.

Filtration Rating.................................................................................... 2.5 Micron

Bag Information

Number of Upper Bags........................................................................................ 1

Number of Lower Bags........................................................................................ 1

Upper Bag Diameter..................................................................................... 19 in.

Upper Bag Length........................................................................................ 33 in.

Lower Bag Diameter..................................................................................... 19 in.

Lower Bag Length........................................................................................ 33 in.

Impeller Information

Impeller Type........................................................................................ Radial Fin

Impeller Size.............................................................................................. 12 in.

Impeller Blade Thickness.............................................................................. 1/8 in.

Construction

Upper Bag................................................................................................ Fabric

Lower Bag................................................................................................ Plastic

Base............................................................................. Steel Sheet Metal w/Casters

Caster..................................................................................... High Density Plastic

Impeller.................................................................................................... Steel

Paint Type/Finish............................................................................. Powder Coated

Blower Housing............................................................................. Steel Sheet Metal

Body......................................................................................... Steel Sheet Metal

Other

Country of Origin ............................................................................................... China

Warranty ....................................................................................................... 2 Years

Approximate Assembly & Setup Time ................................................................. 45 Minutes

Serial Number Location .............................................. ID Label Above Magnetic On/Off Switch

ISO 9001 Factory .................................................................................................. Yes

CSA, ETL, or UL Certified/Listed ................................................................................ No

Features

Large Capacity
Powder-Coated Finish
Includes Steel Base with Casters

-6-

Model W1666/W1685 (For Machines Mfd. Since 2/15)

SAFETY

OWNER’S MANUAL.

TRAINED OPERATORS ONLY.

DANGEROUS ENVIRONMENTS.

MENTAL ALERTNESS REQUIRED.

electrical components or improperly grounded

manual uses a series of symbols and signal words intended to convey the level of importance of the
safety messages. The progression of symbols is described below. Remember that safety messages by

SAFETY

For Your Own Safety,

Read Manual Before Operating Machine

The purpose of safety symbols is to attract your attention to possible hazardous conditions. This

themselves do not eliminate danger and are not a substitute for proper accident prevention mea­sures—this responsibility is ultimately up to the operator!

NOTICE

Standard Machinery Safety Instructions

Standard Machinery Safety Instructions

Indicates an imminently hazardous situation which, if not avoided,
WILL result in death or serious injury.

Indicates a potentially hazardous situation which, if not avoided,
COULD result in death or serious injury.

Indicates a potentially hazardous situation which, if not avoided,
MAY result in minor or moderate injury.

This symbol is used to alert the user to useful information about
proper operation of the equipment or a situation that may cause
damage to the machinery.

SAFETY

Read and understand this

owner’s manual BEFORE using machine.

have a higher risk of being hurt or killed. Only
allow trained/supervised people to use this
machine. When machine is not being used,
disconnect power, remove switch keys, or
lock-out machine to prevent unauthorized
use—especially around children. Make
workshop kid proof!

machinery in areas that are wet, cluttered,
or have poor lighting. Operating machinery
in these areas greatly increases the risk of
accidents and injury.

alertness is required for safe operation of
machinery. Never operate under the influence
of drugs or alcohol, when tired, or when
distracted.

Untrained operators

Do not use

Full mental

ELECTRICAL EQUIPMENT INJURY RISKS. You can

be shocked, burned, or killed by touching live

machinery. To reduce this risk, only allow an
electrician or qualified service personnel to
do electrical installation or repair work, and
always disconnect power before accessing or
exposing electrical equipment.

DISCONNECT POWER FIRST. Always disconnect

machine from power supply BEFORE making
adjustments, changing tooling, or servicing
machine. This eliminates the risk of injury
from unintended startup or contact with live
electrical components.

EYE PROTECTION. Always wear ANSI-approved

safety glasses or a face shield when operating
or observing machinery to reduce the risk of
eye injury or blindness from flying particles.
Everyday eyeglasses are not approved safety
glasses.

-7-

WEARING PROPER APPAREL. Do not wear

clothing, apparel, or jewelry that can become

HAZARDOUS

HEARING PROTECTION.

REMOVE ADJUSTING TOOLS.

INTENDED USAGE.

AWKWARD POSITIONS.

CHILDREN & BYSTANDERS.

GUARDS & COVERS.

FORCING MACHINERY. Do not force machine. It

will do the job safer and better at the rate for

loss of control. Before starting, verify machine

malfunction, leading to serious personal injury

from heated surfaces, high traffic areas, harsh

entangled in moving parts. Always tie back
or cover long hair. Wear non-slip footwear to
avoid accidental slips, which could cause loss
of workpiece control.

DUST. Dust created while using

SAFETY

machinery may cause cancer, birth defects,
or long-term respiratory damage. Be aware of
dust hazards associated with each workpiece
material, and always wear a NIOSH-approved
respirator to reduce your risk.

Always wear hearing
protection when operating or observing
loud machinery. Extended exposure to this
noise without hearing protection can cause
permanent hearing loss.

Tools left on
machinery can become dangerous projectiles
upon startup. Never leave chuck keys,
wrenches, or any other tools on machine.
Always verify removal before starting!

Only use machine for its
intended purpose—never make modifications
without prior approval from Woodstock
International. Modifying machine or using
it differently than intended will void the
warranty and may result in malfunction or
mechanical failure that leads to serious
personal injury or death!

Keep proper footing and
balance at all times when operating machine.
Do not overreach! Avoid awkward hand
positions that make workpiece control difficult
or increase the risk of accidental injury.

Keep children and
bystanders at a safe distance from the work
area. Stop using machine if they become a
distraction.

Model W1666/W1685 (For Machines Mfd. Since 2/15)

which it was designed.

NEVER STAND ON MACHINE. Serious injury may

occur if machine is tipped or if the cutting
tool is unintentionally contacted.

STABLE MACHINE. Unexpected movement during

operation greatly increases risk of injury or

is stable and mobile base (if used) is locked.

USE RECOMMENDED ACCESSORIES. Consult

this owner’s manual or the manufacturer for
recommended accessories. Using improper
accessories will increase risk of serious injury.

UNATTENDED OPERATION. To reduce the risk

of accidental injury, turn machine OFF and
ensure all moving parts completely stop
before walking away. Never leave machine
running while unattended.

MAINTAIN WITH CARE. Follow all maintenance

instructions and lubrication schedules to
keep machine in good working condition. A
machine that is improperly maintained could

or death.

CHECK DAMAGED PARTS. Regularly inspect

machine for any condition that may affect
safe operation. Immediately repair or replace
damaged or mis-adjusted parts before
operating machine.

MAINTAIN POWER CORDS. When disconnecting

cord-connected machines from power, grab
and pull the plug—NOT the cord. Pulling the
cord may damage the wires inside, resulting
in a short. Do not handle cord/plug with wet
hands. Avoid cord damage by keeping it away

chemicals, and wet/damp locations.

accidental contact with moving parts or flying
debris—make sure they are properly installed,
undamaged, and working correctly.

Guards and covers reduce

EXPERIENCING DIFFICULTIES. If at any time

you experience difficulties performing the
intended operation, stop using the machine!

-8-

Contact Technical Support at [phone].

Model W1666/W1685 (For Machines Mfd. Since 2/15)

INTENDED USE. This dust collector is only

HAZARDOUS

DUST ALLERGIES

WEAR RESPIRATOR.

EMPTYING DUST.

DISCONNECTING POWER SUPPLY.

REGULAR CLEANING.

SUSPENDED DUST PARTICLES AND IGNITION

using a grounding wire.

Additional Safety for Dust Collectors

intended for collecting wood dust and chips
from woodworking machines. DO NOT use this
dust collector to collect metal, dirt, pebbles,
drywall, asbestos, lead paint, silica, liquids,
aerosols, or any flammable, combustible, or
hazardous materials.

DUST. Dust created while using
machinery may cause cancer, birth defects,
or long-term respiratory damage. Be aware of
dust hazards associated with each workpiece
material, and always wear a NIOSH-approved
respirator to reduce your risk.

. Dust from certain woods
may cause an allergic reaction in people and
animals. Make sure you know what type of
wood dust you will be exposed to in case
there is a possibility of an allergic reaction.

Fine dust that is too small
to be caught in the filter will be blown into
the ambient air during operation. Always wear
a NIOSH approved respirator during operation
and for a short time after to reduce your risk
of permanent respiratory damage.

When emptying dust from the
collection container, wear a respirator and
safety glasses. Empty dust away from ignition
sources and into an approved container.

switch OFF, disconnect the dust collector from
the power supply, and allow the impeller to
come to a complete stop before leaving the
machine unattended or doing any service,
cleaning, maintenance, or adjustments.

Regularly check/empty
the collection bags or drum to avoid the
buildup of fine dust that can increase the
risk of fire. Make sure to regularly clean
the surrounding area where the machine is
operated—excessive dust buildup on overhead
lights, heaters, electrical panels, or other
heat sources will increase the risk of fire.

Turn the

SOURCES. DO NOT operate the dust collector
in areas where explosion risks are high. Areas
of high risk include, but are not limited to,
areas near pilot lights, open flames, or other
ignition sources.

FIRE SUPPRESSION. Only operate dust collector

in locations that contain a fire suppression
system or have a fire extinguisher nearby.

IMPELLER HAZARDS. DO NOT place your hands

or tools near the open inlet during operation
for any reason. The powerful suction could
easily pull them into the impeller, which
will cause serious personal injury or damage
to the machine. Always keep small animals
and children away from open dust collection
inlets.

AVOIDING SPARKS. DO NOT allow steel or rocks

to strike the impeller—this may produce
sparks. Sparks can smolder in wood dust
for a long time before a fire is detected. If
you accidentally cut into wood containing
tramp metal (nails, staples, spikes, etc.),
immediately turn OFF the dust collector,
disconnect it from power, and wait for the
impeller to stop—then empty the collection
container into an approved airtight metal
container.

OPERATING LOCATION. To reduce respiratory

exposure to fine dust, locate permanently
installed dust collectors away from the
working area, or in another room that is
equipped with a smoke detector. DO NOT
operate the dust collector in rainy or wet
locations—exposure to water may create
an shock hazard or decrease the life of the
machine.

STATIC ELECTRICITY. Plastic dust lines generate

high amounts of static electricity as dust
chips pass through them. Although rare,
sparks caused by static electricity can cause
explosions or fire. To reduce this risk, make
sure all dust lines are thoroughly grounded by

SAFETY

-9-

Model W1666/W1685 (For Machines Mfd. Since 2/15)

This machine must be connected to the correct size and
type of power supply circuit, or fire or electrical damage
may occur. Read through this section to determine if an
adequate power supply circuit is available. If a correct
circuit is not available, a qualified electrician MUST install
one before you can connect the machine to power.

A power supply circuit includes all electrical equipment
between the breaker box or fuse panel in the building
and the machine. The power supply circuit used for
this machine must be sized to safely handle the full­load current drawn from the machine for an extended
period of time. (If this machine is connected to a circuit
protected by fuses, use a time delay fuse marked D.)

The full-load current rating is the amperage a machine
draws at 100% of the rated output power. On machines
with multiple motors, this is the amperage drawn by the
largest motor or sum of all motors and electrical devices
that might operate at one time during normal operations.

or machine damage. To reduce this risk,

a dedicated circuit—

where only one machine will be running

multiple machines will be running at the

This machine is prewired to operate on a 110V power
supply circuit that has a verified ground and meets the
following requirements:

This machine is prewired to operate on a 220V power
supply circuit that has a verified ground and meets the
following requirements:

ELECTRICAL

Circuit Requirements

The machine must be properly set up
before it is safe to operate. DO NOT
connect this machine to the power
source until instructed to do so later in
this manual.

ELECTRICAL

Full-Load Current Rating

W1666 Full-Load Current Rating at 220V ......... 12 A mps

W1685 Full-Load Current Rating at 110V ......... 16 Amps

W1666 Circuit Requirements for 220V

Circuit Type ......................220V, 60 Hz, Single-Phase

Circuit Size ............................................. 15 Amps

Plug/Receptacle .................................... NEMA 6-15

W1685 Circuit Requirements for 110V

Circuit Type ...................... 110V, 60 Hz, Single-Phase

Circuit Size ............................................. 20 Amps

Plug/Receptacle .................................... NEMA 5-20

Incorrectly wiring or grounding this
machine can cause electrocution, fire,

only an electrician or qualified service
personnel should do any required
electrical work on this machine.

NOTICE

The circuit requirements listed in this
manual apply to

at a time. If this machine will be
connected to a shared circuit where

same time, consult with an electrician
to ensure that the circuit is properly
sized for safe operation.

-10-

Model W1666/W1685 (For Machines Mfd. Since 2/15)

This machine MUST be grounded. In the event of certain
types of
a path of least resistance for electric current
order

Improper connection of the equipment-grounding

will
increase
insulation
grounding
cord or plug is necessary, do not connect the equipment­grounding

Check with a qualified electrician or service personnel
if
or if
properly grounded.
plug is damaged or worn, disconnect it from power, and
immediately replace it with a new one.

We do not recommend using an extension cord with

Any extension cord used with this machine must contain a

plug and receptacle, and

meet the following requirements:

the available receptacle or the machine

Grounding Requirements

malfunctions or breakdowns, grounding provides

to travel—in

to reduce the risk of electric shock.

wire

the risk of electric shock. The wire with green

(with/without yellow stripes) is the equipment-

wire. If repair or replacement of the power

wire to a live (current carrying) terminal.

you do not understand these grounding requirements,

you are in doubt about whether the tool is

If you ever notice that a cord or

For W1666 220V Connection

A NEMA 6-15 plug has a grounding prong that must be
attached to the equipment-grounding wire inside the
included power cord. The plug must only be inserted
into a matching receptacle (see Figure 1) that is properly
installed and grounded in accordance with all local codes.

For W1685 110V Connection

A NEMA 5-15 plug has a grounding prong that must be
attached to the equipment-grounding wire inside the
included power cord. The plug must only be inserted
into a matching receptacle (see Figure 2) that is properly
installed and grounded in accordance with all local codes.

220V

Current Carrying Prongs

6-15 PLUG

Figure 1. NEMA 6-15 plug & receptacle.

No adapter should be used with the
required plug. If the plug does not fit

must be reconnected to a different
type of circuit, the reconnection must
be made by an electrician or qualified
service personnel and it must comply
with all local codes and ordinances.

110V

GROUNDED

6-15 RECEPTACLE

Grounding Prong

GROUNDED

5-15 RECEPTACLE

Grounding Prong

ELECTRICAL

Extension Cords

this machine. Extension cords cause voltage drop, which
may damage electrical components and shorten motor
life. Voltage drop increases with longer extension cords
and smaller gauge sizes (higher gauge numbers indicate
smaller sizes).

ground wire

Minimum Gauge Size .................................12 AWG

Maximum Length (Shorter is Better) ................50 ft.

, match the required

5-15 PLUG

Neutral Hot

Figure 2. NEMA 5-15 plug & receptacle.

-11-

Model W1666/W1685 (For Machines Mfd. Since 2/15)

SETUP

Unpacking

This machine has been carefully packaged for safe
transportation. If you notice the machine has been
damaged during shipping, please contact your authorized
Shop Fox dealer immediately.

Inventory

The following is a description of the main components
shipped with the Model W1666/W1685. Lay the
components out to inventory them.

Note: If you can't find an item on this list, check the
mounting location on the machine or examine the
packaging materials carefully. Occasionally we pre-install
certain components for safer shipping.

B

A

G

H

P

I

M

Figure 3. Shipping inventory.

J

L

Q

F

D

C

E

K

O

N

Shipping Inventory (Figure 3): Qty

SETUP

A. Base Plate ..................................................1

B. Outlet Flange 5" ...........................................1

C. Outlet Gasket ..............................................1

D. Impeller/Motor Assembly .................................1

E. Separator ...................................................1

F. Motor Mount ................................................1

G. Transfer Hose 5" ...........................................1

H. Inlet Y-Connector 6" x (2) 4" .............................1

I. Hose Clamps 5" ............................................2

J. Bag Clamps .................................................2

K. Swivel Casters ..............................................4

L. Wrenches, 8/10mm & 11/13mm Open Ends ...1 Each

M. Bags, Upper & Lower .............................. 1 Each

N. Separator Supports ........................................3

O. Upper Bag Hanger .........................................1

P. Hex Wrench 5mm ..........................................1

Q. Hardware Bags for W1666

— Hex Bolts M8-1.25 x 16 ............................... 26

— Hex Bolts M8-1.25 x 25 .................................4

— Flat Washers 8mm..................................... 34

— Hex Nuts M8-1.25 .......................................4

— Phillips Head Screws M6-1 x 10 ..................... 16

— Flat Washers 6mm..................................... 16

— Hex Nuts M6-1 ......................................... 16

Keep machine disconnected from
power until instructed otherwise.

Q. Hardware Bags for W1685

— Hex Bolts M8-1.25 x 16 ............. 18

— Hex Bolts M8-1.25 x 25 .............. 4

— Flat Washers 8mm................... 26

— Hex Nuts M8-1.25 .................... 4

— Phillips Head Screws M6-1 x 10 ...16

—Hex Bolts M6-1 x 20 .................. 6

— Flat Washers 6mm................... 28

— Hex Nuts M6-1 ....................... 22

-12-