sharp FO77U, FO77, UX66 Service Manual

SERVICE MANUAL

No. 00ZFO77U//SME

FACSIMILE

FO-77

MODEL UX-66

FO-77U UX-66U

Illustration: FO-77

CONTENTS

CHAPTER 1. GENERAL DESCRIPTION

[1] Specifications ............................................ 1-1

[2] Operation panel......................................... 1-2

[3] T r ansmittable documents .......................... 1-3

[4] Installation ................................................. 1-4

[5] Quick reference guide ............................... 1-9

[6] Quick setup guide (UX-66U only)............ 1-10

CHAPTER 2. ADJUSTMENTS

[1] Adjustments .............................................. 2-1

[2] Diagnostics and service soft switch .......... 2-2

[3] T roub leshooting ...................................... 2-18

[4] Error code table....................................... 2-19

CHAPTER 3. MECHANISM BLOCKS

[1] General description ................................... 3-1

[2] Disassembly and assembly

procedures ....................................... 3-3

CHAPTER 5. CIRCUIT DESCRIPTION

[1] Circuit description ..................................... 5-1

[2] Circuit description of control PWB ............ 5-2

[3] Circuit description of TEL/LIU PWB .......... 5-9

[4] Circuit description of

power supply PWB............................5-12

[5] Circuit description of CIS unit...................5-12

CHAPTER 6. CIRCUIT SCHEMATICS AND PARTS LAYOUT

[1] Control PWB circuit ................................... 6-1

[2] TEL/LIU PWB circuit.................................. 6-9

[3] Power supply PWB circuit ...................... 6-13

[4] Operation panel PWB circuit ................... 6-15

CHAPTER 7. OPERATION FLOWCHART

[1] Protocol ..................................................... 7-1

[2] Power on sequence................................... 7-2

CHAPTER 4. DIAGRAMS

[1] Block diagram ............................................4-1

[2] Wiring diagram .......................................... 4-2

[3] Point-to-point diagram ............................... 4-3

Parts marked with " " is important for maintaining the safety of the set. Be sure to replace these parts with specified ones for maintaining the safety and performance of the set.

SHARP CORPORATION

CHAPTER 8. OTHERS

[1] Service tools ............................................. 8-1

[2] IC signal name .......................................... 8-4

PARTS GUIDE

This document has been published to be used for after sales service only. The contents are subject to change without notice.

FO-77U UX-66U

CAUTION FOR BATTERY REPLACEMENT

(Danish) ADVARSEL !

Lithiumbatteri-Eksplosionsfare ved fejlagtig håndtering.

Udskiftning må kun ske med batteri af samme fabrikat og type.

Levér det brugte batteri tilbage til leverandoren.

(English) Caution !

Danger of explosion if battery is incorrectly replaced.

Replace only with the same or equivalent type

recommended by the equipment manufacturer.

Discard used batteries according to manufacturer’s

instructions.

(Finnish) VAROITUS

Paristo voi räjähtää, jos se on virheellisesti asennettu.

Vaihda paristo ainoastaan laitevalmistajan suosittelemaan

tyyppiin. Hävitä käytetty paristo valmistajan ohjeiden

mukaisesti.

(French) ATTENTION

Il y a danger d’explosion s’ il y a remplacement incorrect

de la batterie. Remplacer uniquement avec une batterie du

même type ou d’un type recommandé par le constructeur.

Mettre au rébut les batteries usagées conformément aux

instructions du fabricant.

(Swedish) VARNING

Explosionsfare vid felaktigt batteribyte.

Använd samma batterityp eller en ekvivalent

typ som rekommenderas av apparattillverkaren.

Kassera använt batteri enligt fabrikantens

instruktion.

(German) Achtung

Explosionsgefahr bei Verwendung inkorrekter Batterien.

Als Ersatzbatterien dürfen nur Batterien vom gleichen Typ oder

vom Hersteller empfohlene Batterien verwendet werden.

Entsorgung der gebrauchten Batterien nur nach den vom

Hersteller angegebenen Anweisungen.

CHAPTER 1. GENERAL DESCRIPTION

[1] Specifications

FO-77U UX-66U

Automatic dialing: Rapid Key Dialing: 5 numbers

Speed Dialing: 35 numbers

Thermal paper: Initial starter roll (included with machine):

32 ft. (10 m) Recommended replacement roll: FO-20PRw, 98 ft. (30m), 0.5" core

Paper cutting method: Automatic cutter Modem speed: 9600 bps with automatic fallback to lower

speeds

Transmission time* : Approx. 15 seconds Resolution: Horizontal: 203 pels/inch (8 dots/mm)

Vertical:

Standard: 98 lines/inch (3.85 lines/mm) Fine/Halftone: 196 lines/inch (7.7 lines/mm) Super fine: 391 lines/inch (15.4 lines/mm)

Automatic document feeder: 5 pages max. (20 lb paper) Halftone (grayscale): 64 levels Display: 16-digit LCD display Compression scheme: MR, MH, Sharp (H2) Applicable telephone line: Public switched telephone network Compatibility: ITU-T (CCITT) G3 mode Input document size: Automatic feeding:

Width: 5.8 to 8.5" (148 to 216 mm) Length: 5.5 to 11" (140 to 279 mm)

Manual feeding:

Width: 5.8 to 8.5" (148 to 216 mm) Length: 5.5 to 23.6" (140 to 600 mm)

Effective scanning width: 8.3" (210 mm) max. Effective printing width: 8.3" (210 mm) max. Contrast control: Automatic/Dark selectable Reception modes: Fax/Tel Copy function: Yes Telephone function: Yes (cannot be used if power fails) Power requirements: 120 V AC, 60 Hz Operating temperature: 41 - 95°F (5 - 35°C) Humidity: Maximum: 85 % RH Power consumption: Standby: 3.6 W

Maximum: 100 W

Dimensions: Width: 12.0" (304 mm)

Depth: 9.3" (236 mm)

Height: 4.8" (122 mm) Weight: Approx. 5.7 lbs. (2.6 kg) * Based on ITU-T (CCITT) Test Chart #1 at standard resolution in Sharp

special mode, excluding time for protocol signals (i.e., ITU-T phase C time only).

Note: The facsimile machine is Year 2000 compliant.

As a part of our policy of continuous improvement, SHARP reserves the right to make design and specification changes for procduct improvement without prior notice. The performance specifications figures indicated are nominal values of production units. There may be some deviation from these values in individual units.

1 – 1

FO-77U UX-66U

[2] Operation panel

GHI

PQRS

ABC

JKL

TUV

START

1 4 5 62 3

TEL FAX

A.M.

DEF

MNO

WXYZ

STOP

RECEPTION

TEL FAX

DOWN VOLUME UP

SPEED DIAL

REDIAL

HOLD/SEARCH

SPEAKER

MODE

COPY/

RECEPTION MODE

HELP

RESOLUTION FUNCTION

GHI

VOLUME

PQRS

FUNCTION

RESOLUTION/

10/POLL

STOP

SPEED

DIAL

REDIAL

HOLD/

SPEAKER

ABC

JKL

TUV

DEF

MNO

COPY/HELP

WXYZ

START

1. Rapid Dial keys

Press one of these keys to dial a fax or voice number automatically.

2. Display

This displays messages and prompts during operation and programming.

3. FUNCTION key

Press this key to select various special functions.

4. VOLUME keys

Press this keys to adjust the volume of the speaker when the SPEAKER key has been pressed, the volume of the handset when the handset is lifted, or the volume of the ringer at all other times.

5. Number keys

Use these keys to dial numbers, and enter numbers and letters storing auto-dial numbers.

6. SPEED DIAL key

Press this key to dial a fax or voice number using an abbreviated 2-digit Speed Dial number.

7. REDIAL key

Press this key to automatically redial the last number dialed.

8. START key

Press this key to begin transmission when using Speed Dialing, Direct Keypad Dialing, or Normal Dialing.

9. STOP key

Press this key to cancel operation before it is completed.

11109

1314

10. COPY/HELP key

When a document is in the feeder, press this key to make a copy of a document. At any other time, press this key to print out the Help List, a quick reference guide to the opeation of your fax machine.

11. RESOLUTION/RECEPTION MODE key

When a document is in the feeder, press this key to adjust the resolution for faxing or copying. At any other time, press this key to select the reception mode (an arrow in the display will point to the currently selected reception mode).

12. SPEAKER key

Press this key to listen the line and fax tones through the speaker when faxing a document. Note: This is not a speakerphone. You must pick up the handset to talk with the other party.

13. HOLD/SEARCH key

Press this key to search for an auto-dial number, or, during a phone conversation, press this key to put the other party on hold.

14. Panel release

Grasp this finger hold and pull toward you to open the operation panel.

1 – 2

[3] T ransmittab le documents

[

]

[

]

(

)

1. Document Sizes

Normal size

(Min.)

140mm

148mm 216mm

Use document carrier sheet for smaller documents.

* With special sizes, only one sheet can be fed into the machine at a

time. Insert next page into feeder as current page is being scanned.

2. Paper Thickness & Weight

width 5.8" – 8.5" (148 – 216 mm)

length 5.5" – 11" (140 – 279 mm)

(Max.)

(Max.) Letter

279mm

600mm

size

216mm

Normal size

Special size

FO-77U UX-66U

5. Automatic Document Feeder Capacity

Number of pages that can be placed into the feeder at anytime is as follows:

Normal size: max. ADF 5 sheets Special size: single sheet only (manual feed)

NOTES: • When you need to send or copy more pages than the feeder

limit, place additional pages in feeder when last page in feeder is being scanned.

• Place additional pages carefully and gently in feeder .

If force is used, double-feeding or a document jam may result.

6. Readable Width & Length

The readable width and length of a document are slightly smaller than the actual document size.

Note that characters or graphics outside the effective document scanning range will not be read.

• Readable width

8.3" (210mm), max.

4x6 series (788mm x 1091mm x 1000mm sheets)

Minimum Maximum Minimum Maximum Feeder capacity 5 sheets, max. Paper weight 45kg 69.2kg 52g/m Paper thickness (ref.) Paper size 148mm x 140mm ~

0.06mm 0.09mm 0.06mm 0.09mm

A4 (210mm x 297mm), Letter (216mm x 279mm)

Square meter series

80g/m

3. Document Types

• Normal paper Documents handwritten in pencil (No. 2 lead or softer), fountain

pen, ball-point pen, or felt-tipped pen can be transmitted. Documents of normal contrast duplicated by a copying machine

can also be transmitted.

• Diazo copy (blue print) Diazo copy documents of a normal contrast may be transmitted.

• Carbon copy A carbon copy may be transmitted if its contrast is normal.

4. Cautions on Transmitting Documents

• Documents written in yellow, greenish yello w, or light b lue ink cannot be transmitted.

• Ink, glue, and correcting fluid on documents must be dry before the documents can be transmitted.

• All clips, staples and pins must be removed from documents before transmission.

• Patched (taped) documents should be copied first on a copier and then the copies used for transmission.

• All documents should be fanned before insertion into the feeder to prevent possible double feeds.

Readable width

• Readable length

This is the length of the document sent minus 0.2" (5mm) from the top and bottom edges.

0.2"(5mm)

Readable length

0.2"

5mm

1 – 3

FO-77U UX-66U

7. Use of Document Carrier Sheet

A document carrier sheet must be used for the following documents.

• Those with tears.

• Those smaller than size 5.8" (W) x 5.5" (L) (148mm (W) x 140mm

(L)).

• Carbon-backed documents

TELEPHONE JACK

A standard RJ11C telephone jack must be located near the machine. This is the telephone jack commonly used in most homes and offices.

• Plugging the fax machine into a jac k which is not an RJ11C jac k may

result in damage to the machine or your telephone system. If you do not know what kind of jack you have, or need to have one installed, contact the telephone company.

Make print straight across paper E.G. Place the document carrier in the document feeder with the clear film side down

Direction of insertion

NOTE: To transmit a carbon-backed document, insert a white sheet of

paper between the carbon back of the document and the document carrier.

• Those containing an easily separable writing substance (e.g., trac-

ing paper written on with a soft, heavy lead pencil).

NOTES: • When using the document carrier, carefully read the in-

structions written on the back.

• If the document carrier is dirty, clean it with a soft, moist

cloth, and then dry it before using for transmission.

• Do not place more than one document in the carrier at a

time.

[4] Installation

1. Site selection

T ake the f ollowing points into consideration when selecting a site f or this model.

ENVIRONMENT

• The machine must be installed on a level surface.

• Keep the machine away from air conditioners, heaters, direct sun-

light, and dust.

• Provide easy access to the front, back, and sides of the machine. In

particular, keep the area in front of the machine clear , or the original document may jam as it comes out after scanning.

• The temperature should be between 5° and 35°C.

• The humidity should be between 30% and 85% (without conden-

sation).

ELECTRICITY

AC 120V, 60Hz, grounded (3-prong) AC outlet is required.

Caution!

• Connection to a power source other than that specified will cause

damage to the equipment and is not covered under the warranty.

• If your area experiences a high incidence of lightning or power surges,

we recommend that you install a surge protector for the power and telephone lines. Surge protectors can be purchased at most telephone specialty stores.

If the machine is moved from a cold to a warm place...

Condensation may from on the reading glass if machine is moved from a cold to a warm place, this will prevent proper scanning of documents for transmission. Turn on the pow er and w ait approximately 2 hours before using machine.

2. Assembly and connections

Plug the power cord into a 120 V, 60 Hz, grounded (3-prong) AC outlet.

• Caution: Do not plug the power cord into an y other kind of outlet.

This will damage the machine and is not covered under the warranty.

• The machine does not have a power on/off switch, so the po wer is

turned on and off by simply plugging in or unplugging the power cord.

Connect the handset as shown and place it on the handset rest.

♦ The ends of the handset cord are identical, so they will go into

either jack.

Make sure the handset cord goes into the jack marked with a handset symbol on the side of the machine!

Use the handset to make ordinary phone calls, or to transmit and receive faxes manually.

Attach the original document support as shown below.

1 – 4

Insert one end of the line cord into the jack on the back of the ma-

chine marked TEL. LINE. Insert the other end into a standard (RJ11C) single-line wall telephone jack.

TEL. LINE

Note: The fax machine is set for touch-tone dialing. If you are on a

pulse dial (rotary) line, you must set the fax machine for pulse dialing. Press the keys on the operation panel as follows:

Flip up the front paper guide.

Remove the tape and packing paper from the cutter unit.

FO-77U UX-66U

1. Press these keys:

The display will show:

DIAL MODE

2. Press 1 to select tone (touch-tone)

dialing, or 2 to select pulse (rotary) dialing.

3. Press the STOP key to return to the date

and time display.

FUNCTION

TONE

STOP

3. Removing the packing paper

Grasp the finger hold and pull up to open the operation panel.

PULSE

Flip down the front paper guide and then close the operation panel.

1 – 5

FO-77U UX-66U

4. Loading the thermal paper (FO-20PRw)

• Your f ax machine prints incoming fax es on a special kind of paper called thermal paper.

• The fax machine’s print head creates text and images by applying heat to the thermal paper.

Grasp the finger hold as shown and pull up to open the operation panel.

Insert the leading edge of the paper into the slot as shown. Continue

to push the paper through the slot until it comes out the opening in the front of the machine.

Make sure the paper comes out straight, and then flip down the pa-

per guide.

Flip up the front paper guide.

Press the knob to make sure the front side of the metal guide is down.

Unwrap the roll of thermal paper and place it in the compartment.

♦ Important: The roll must be placed so the leading edge of the

paper unrolls as shown. (The paper is only coated on one side for printing. If the roll is placed backwards, the paper will come out blank after printing.)

YES

NO!

Close the operation panel, making sure it clicks into place.

• A short length of the paper will be cut off.

1 – 6

Click!

5. Clearing a jammed document

If the original document doesn’t feed properly during transmission or copying, or DOCUMENT JAMMED appears in the display, first try pressing the START key . If the document doesn’t f eed out, open the operation panel and remove it.

Important:

Do not try to remove a document without first releasing it as explained below. This may damage the feeder mechanism.

Grasp the finger hold and pull up to open the operation panel.

Flip down the green levers on each side of the white roller.

Close the operation panel, making sure it clicks into place.

• Press down on both front corners of the panel to make sure it clicks into place.

FO-77U UX-66U

Flip up the green levers on each side of the white roller.

Remove the document.

1 – 7

FO-77U UX-66U

6. Clearing jammed paper

If the thermal paper jams, PAPER JAMMED will appear in the display. Follow the steps below to clear the jam.

Grasp the finger hold and pull up to open the operation panel.

Cut off the wrinkled part of the paper.

Reload the paper.

• Jammed paper is often caused by improper loading. Be sure to carefully follow the instructions for paper loading given in Loading the Thermal Paper.

Flip up the front paper guide.

Press the knob to make sure the front side of the metal guide is down.

Remove the paper roll.

• Remove any cut pieces of paper from the paper compartment.

1 – 8

[5] Quick reference guide

Beep

START

RECEIVING

START

ENTERING YOUR NAME AND NUMBER

1. Press:

2. Press:

3. Enter your fax number (max. of 20 digits) by pressing the number keys.

• To insert a space between digits, press the # key.

• If you make a mistake, press the SPEED DIAL k ey to bac kspace and clear the

4. Press:

5. Enter your name by pressing the appropriate number keys as shown below.

• T o enter two letters in succession that require the same ke y , press the SPEAKER

SPACE =

A = B =

C =

D =

E =

F =

G =

H =

I =

• To change case, press the REDIAL key.

6. When finished, press:

SETTING THE DATE AND TIME

1. Press:

2. Press:

3. Enter two digits for the Month (01 through 12).

4. Enter two digits for the Day (01 through 31).

5. Enter four digits for the Year (Ex: 1999).

6. Enter two digits for the Hour (01 through 12).

7. Enter two digits for the Minute (00 through 59).

8. Press the

9. When finished, press:

STORING AND CLEARING AUTO DIAL NUMBERS

1. Press:

2. Press 1 to store a number or 2 to clear a number.

3. Enter a 2-digit Speed Dial number (from 01 to 05 for Rapid Key Dialing, or 06 to

4. Enter the full telephone/fax number.

5. Press:

6. Enter the name of the location by pressing number keys (Refer to the letter

7. Press:

FUNCTION

Display shows: OWN NUMBER SET

START

mistake.

START

key after entering the first letter.

J =

K =

L =

M =

N =

O =

P =

Q = R =

S =

T = U =

V =

W =

X =

Y =

Z =

Press # or to scroll through symbols and special characters.

STOP

FUNCTION

START

Display shows: DATE & TIME SET

START

key for A.M. or the # key for P.M.

START

FUNCTION

STOP

Display shows: FAX/TEL # MODE

40 for Speed Dialing) (If you are clearing a number, go to Step 7.)

START

entry table in

ENTERING YOUR NAME AND NUMBER

START

STOP

FO-77U UX-66U

SENDING FAXES

Place your document (up to 5 pages) face down in the document feeder.

Normal Dialing

1. Lift the handset or press

2. Dial the fax number.

3. Wait for the reception tone (if a person answers, ask them to press their Start key).

4. Press:

START

Rapid Key Dialing

Press the appropriate Rapid Key. Transmission will begin automatically.

Speed Dialing

SPEED

1. Press:

DIAL

2. Enter 2-digit Speed Dial number.

3. Press:

START

RECEIVING FAXES

Press the RESOLUTION/RECEPTION MODE key until the arrow in the display points to the desired reception mode (make sure the document feeder is empty).

RESOLUTION/

RECEPTION MODE

FAX mode: The fax machine automatically answers on four rings and receives the

incoming document.

TEL mode:

SETTING THE DISPLAY LANGUAGE

1. Press:

2. Press:

3. Press the # key or

4. Press:

5. Press:

FUNCTION

START

STOP

SPEAKER

TEL

NOV 05 10:30

FAX

TEL

key until the desired language appears in the display.

1 – 9

FO-77U UX-66U

[6] Quick setup guide (UX-66U only)

UX-66 FAX

QUICK SETUP GUIDE

Remove the packing paper.

1. Grasp the finger hold and pull up to open the operation panel.

3. Remove the tape and packing paper.

Plug the power cord into

a 120 v, 60Hz, grounded AC (3-prong) outlet.

Note: To enter your name and fax number and set the date and time so that they appear on the automatic cover sheet, see pages 19 - 25 of your operation manual.

2. Flip up the front paper guide.

4. Flip down the front paper guide and close the operation panel.

Connect the telephone

line cord to the TEL. LINE jack and a wall telephone jack.

Connect the handset

and place it on the handset rest.

Note: Make sure that the area in front of the machine is clear.

Attach the document

support.

Load the thermal paper.

1. Grasp the finger hold and pull up to open the operation panel.

4. Insert the leading edge of the paper into the slot. Push the paper through until it comes out the opening on the front of the machine.

TEL. LINE

2. Flip up the front paper guide.

Press the knob to make sure the front side of the metal guide is down.

5. Make sure the paper comes out straight, and then flip down the paper guide.

3. Unwrap the roll of thermal paper and place it in the compartment.

YES

6. Close the operation panel, making sure it clicks into place.

NO!

1 – 10

(TCADZ2869XHZZ)

CHAPTER 2. ADJUSTMENTS

(step 1) Select "OPTION SETTING".

KEY : FUNCTION 4

DISPLAY: OPTION SETTING PRESS OR #

(step 2) Select "DIAL MODE".

KEY: Push # until " DAIL MODE " is indicated because the number of # s changes by the model.

DISPLAY: DIAL MODE

(step 3) Select, using "1" or "2".

KEY: 1

DISPLAY: TONE SELECTED

KEY: 2

DISPLAY: PULSE SELECTED

(step 4) End, using the "STOP" key.

KEY:

Cursor When initially registering, the mode shows 1=TONE. When registering again, the mode which was registered formerly is shown.

STOP

1=TONE, 2=PULSE

[1] Adjustments

General

Since the following adjustments and settings are provided f or this model, make adjustments and/or setup as necessary.

1. Adjustments Adjustments of output voltage (FACTORY ONLY)

1. Install the power supply unit in the machine.

2. Set the recording paper and document.

3. When the document is loaded, pow er is supplied to the output lines . Confirm that outputs are within the limits below.

Output voltage settings

FO-77U UX-66U

3. Settings Dial mode selector

DIAL mode (Soft Switch No. SWB4 DATA No. 2)

TEL/LIU PWB

CNL IUA

CNLIUA

CONTROL PWB

Output Voltage limits

+5V 4.75V ∼ 5.25V

+24V 24.0V ∼ 26.0V

Pin No.

2. IC protectors replacement

ICPs (IC Protectors) are installed to protect the motor driver circuit. ICPs protect various ICs and electronic circuits from an overcurrent condition.

The location of ICPs are shown below:

CNLIUA

CNMT

CONTROL PWB

(TOP SIDE)

FU100

(1)FU100 (KAB2402) is installed in order to protect IC’s from an over-

current generated in the motor drive circuit. If FU100 is open, replace it with a new one.

POWER SUPPLY PWB

CN2

CNPW

Connector

No. CNPW

1DG 2 +5V 3MG 4MG 5 +24V 6 +24V

CNPW

4. V olume setting

You can adjust the volume of the speaker, ringer , and handset using the

VOLUME key.

(1) Speaker

Press the SPEAKER key.

Press the VOLUME ke y one or more times to select the desired lev el.

The display will show:

SPEAKER VOLUME

Press the SPEAKER key once again to turn off the speaker.

(2) Handset

Lift the handset.

Press the VOLUME key to select the desired level.

The display will show:

RECEIVER VOLUME

Replace the handset.

• Note: The handset volume reverts to medium each time you hang up.

(3) Ringer

Press the VOLUME ke y to select the desired v olume. (Make sure the

SPEAKER key has not been pressed and the handset is not lifted.)

The display will show:

RINGER VOLUME

If you want to turn off the ringer, continue to press the VOLUME key

until RINGER OFF: OK? appears in the display, and then press the START key.

2 – 1

FO-77U UX-66U

[2] Diagnostics and service soft switch

1. Operating procedure (1) Entering the diagnostic mode

Press FUNC → 9 → → 8 → # → 7 , and the following display will appear. ROM Ver. FZG0

FZG0 Then press the START key and country name selected by country select will appear. Select the desired item with the key or the # key or select

with the direct key. Enter the mode with the START key. (Diag•specifications)

FUNC

9 8 7

After 2 sec: DIAG MODE

FZG0

DIAG MODE

START —Soft switch mode

START

START START START START START CSignal send mode START —Memory clear START

If the diag mode cannot be set, repeat the diag mode operation, performing the following operation. After the power is turned on and "WAIT A MOMENT" is indicated, press the STOP key.

"Power ON"

STOP

KEY

Memory clear (Work + Backup)

START

KEY

AROM & RAM check

—Aging mode —Panel check mode

BCheck pattern

—Shading mode

In relation with the process response (request from Production Engineering) "WAIT A MOMENT" clock indication ma y appear depending on STOP ke y timing. If the ST OP ke y is held down, "MEMORY CLEAR?" appears.

— —

— — —

START START START START

START E D

START

Entry data receive

Entry data send

Auto feeder mode

2. Diagnostic items

ITEM DIRECT

No. key

1 — SOFT SWITCH MODE Soft switches are displayed and changed. List can be output. 2 A ROM & RAM CHECK ROM is sum-checked, and RAM is matched. Result list is output. 3 — AGING MODE 10 sheets of check patterns are output every 5 minutes per sheet. 4 — PANEL CKECK MODE Panel keys are tested. Result list is output. 5 B CHECK PATTERN 2 sheets of check patterns are output. 6 C SIGNAL SEND MODE Various signals of FAX communication are output. 7 — MEMORY CLEAR Back-up memory is cleared, and is set at delivery. 8 — SHADING MODE Shading compensation is performed in this mode.

9 D ALL BLACK PRINT To check the print head, whole dots are printed over the interval of 2 m. 10 E AUTO FEEDER MODE Insertion and discharge of document are tested. 11 — ENTRY DATA SEND Registered content is sent. 12 — ENTRY DATA RECEIVE Registered content is received, and its list is output. 13 — MESSAGE PRINT The display message of each language is printed out together with the English equivalent. 14 — CUTTER AGING Recording paper is successively cut. 15 — COUNTRY SELECT The software parameter that it agreed in each country name is set up.

Contents Function

Country select

Cutter aging

Message print

All black mode

2 – 2

3. Diagnostic items description

3. 1. Soft switch mode

The soft switches are provided so that each operation mode can be set by using the operation panel.

In this mode, these switches can be checked and set. The contents of these switches are backed up. The available soft switches are SW-A1 to SW-K1. The content of soft switches is shown in page 2-5 to 2-17. The contents are set to factory default settings.

3. 2. ROM & RAM check

ROM executes the sum check, and RAM executes the matching test. The result will be notified with the number of short sounds of the buzzer as well as by printing the ROM & RAM check list. Number of short sounds of buzzer 0 → No error

1 → ROM error 2 → RAM error (32Kbyte)

3. 3. Aging mode

If any document is first present, copying will be ex ecuted sheet by sheet. If no document is present, the check pattern will be printed sheet by sheet. This operation will be executed at a rate of one sheet per 5minutes, and will be ended at a total of 10 sheets.

3. 4. Panel check mode

This mode is used to check whether each key operates properly or not. Press the key on the operation panel, and the key will be displayed on the display . Therefore, press all k eys. At this time,finally press the STOP key.

When the STOP key is pressed, the keys which are not judged as "pressed" will be printed on the result list.

• LED part of the contact image sensor (CIS) is kept on during the term from when "ST AR T" of the panel test mode to end with the STOP k ey.

FO-77U UX-66U

3. 6. Signal send mode

This mode is used to send various signals to the circuit during FAX communication. Every push of START key sends a signal in the following sequence. Moreov er , the signal sound is also output to the speaker when the line monitor of the soft switch is on.

[1] No signal (CML signal turned on) [2] 9600bps [3] 7200bps [4] 4800bps [5] 2400bps [6] 300bps (FLAG) [7] 2100Hz (CED) [8] 1100Hz (CNG) [9] Pseudo Ring (models with auto TEL/FAX changeover function) [10] END

3. 7. Memory clear

This mode is used to clear the backup memory and to reset to the factory default settings. The content of each setting will be cleared.

Note: Be sure to ex ecute the memory clear mode whenev er you change

the country select setting. The def ault settings of the soft s witches vary according to the destinations. Theref ore, if you do not e xecute the memory clear after changing the country select setting, some functions may not work.

3. 8. Shading mode

The mode is used for the shooting compensation. For reading, set up the special original paper.

The shooting compensation memorizes the reference data of white and black for reading.

Moreover, the memoriz ed data is not erased ev en if memory clear mode is executed.

3. 5. Check pattern

This mode is used to check the status of print head. Two sheets of check pattern are printed. The f ollowing information of check pattern is printed.

Vertical stripes (alternate white and black lines) Approx. 35 mm

Full black Approx. 70 mm

Full white Approx. 35 mm

RANK 0 or 1

Note: There is a selection RANK 0 or 1 depending on resistance value of the thermal head. RANK 0 or RANK 1 is printed at the tail of check pattern to identify.

3. 9. All black print

This mode is used to check the state of the printing head and intentionally overheat it. Whole dots are printed over the interval of 2 m. If it is overheated or the printing sheet is jammed, press STOP ke y for the end.

3. 10. Auto feeder mode

In this mode, a document is inserted and discharged to check the auto feed function.

After this mode is started, set a document, and the document feed will be automatically tested.

3. 11. Entry data send

This mode is used to send the registered data to the other machine and to make the other machine copy the registered content. Before sending in this mode, it is necessary to set the other machine at the entry data receive mode.

The contents to be sent are as follows (the machine prints each list after the transmission has completed):

1. Telephone list data

2. Sender (cover sheet) register data

3. Optional setting content

4. Soft switch content

5. Junk fax number list

6. Country setting content

2 – 3

FO-77U UX-66U

3. 12. Entry data receive

This mode is used to receive the registered data from the other machine and to make your machine register the received data. Before receiving in this mode, it is necessary to set the other machine at the entry data send mode.

After receiving is completed, the machine prints the following lists:

1. Telephone list data

2. Soft switch list

3. Junk fax number list

3. 13. Message print

In this mode, all the message data, which are used for displaying indication and list print, are printed as a contrast table of the selected language and English.

3. 14. Cutter aging

This mode is used to consecutively cut the recording paper about 10 mm long and to display the number of cutting times.

(The number of cutting times is cumulatively counted unless you execute the memory clear.)

The operation is stopped in the following cases:

1. Hold down the stop key. (The cutter aging is stopped.)

2. No recording paper. (The cut operation is stopped.)

3. Recording paper jam. (The cut operation is stopped.)

3. 15. Country select

This mode is used to set line connecting parameters which correspond to each destination.

When the country select mode is selected, and then the START key is pressed, the destination (country name) currently set will be displayed.

By pressing the # or k ey, selectable destinations (country names) are displayed. When the destination (country name) you want to choose is displayed, press the START key. Each parameter will be stored in RAM.

Destinations (Country names) you can select are as follows:

COUNTRY COUNTRY CODE U. S. A (U) 00 CANADA (C) 01 LATIN AMERICA (LA/LU) 02 ARGENTINA (AR) 03

Note: Be sure to execute the memor y clear mode whenever you

change the country select setting. The default settings of the soft switches vary according to the destinations. Therefore, if you do not execute the memory clear after changing the country select setting, some functions may not work.

Do not set a country select setting which is different from that of the destination of the machine. Some functions will not w ork because the function and the PWB specifications are different.

4. How to make soft switch setting

To enter the soft switch mode, press the following key entries in sequence.

Press

FUNCTION

9 8 7 START START

DATA No. 1 2 3 4 5 6 7 8

S F T SW-A1 = 0 0 0 0 0 0 0 0 S F T SW-A1 = 1 0 0 0 0 0 0 0 S F T SW-A1 = 1 0 0 0 0 0 0 0 S F T SW-A1 = 1 0 0 0 0 0 0 0 S F T SW-A1 = 1 0 0 0 0 0 0 0

S F T SW-A2 = 0 0 0 0 0 0 0 0 S F T SW-M2 = 0 0 0 0 0 0 0 0

Press FUNCTION key.

Press key.

Bit1 - 8 are set.

Press key during setting.

START

Soft SW-A2 - SW-K1 are set.

To finish the settings halfway between SW-A1 and SW-K1, press the STOP key. In this case, the setting being done to the SW No. on display will be nullified while settings done to the preceding SW Nos. remain in effect.

When the COPY key is pressed, the contents of soft switches are printed.

The soft switch mode is terminated.

2 – 4

5. Soft switch description

• Soft switch

FO-77U UX-66U

DA TA

NO.

1 Protect from echo No Ye s 0 2 Forced 4800bps reception Yes No 0 3 Footer Print Yes No 0

4 Length limitation of copy/send/receive No limit Copy/Send:60cm 0

5 CSI transmission Not transmitted Transmitted 0

6 DIS receive acknowledgement during G3 Twice NSF:Once 0

transmission DIS:Twice

7 Non modulated carrier for V29 transmission Yes No 0

mode

8 Reserved 1

Modem speed V.29 V.27 ter

1 No. 100000 2 No. 2 0 0 0 0 0 3 No. 3 0 1 1 0 0

4 No. 411001

5 Reserved 1 6 H2 mode No Yes 0

7 Communication error treatment in RTN No communication error Communication error 0

sending mode(Reception)

8 CNG transmission No Yes 0

CED tone signal interval 1000ms 750ms 500ms 75ms

1 No. 1 1 1 0 0 0 2 No. 2 1 0 1 0 0 3 MR Coding No Yes 0

4 Reserved 0

5 Reserved 0 6 Reserved 0

7 Reserved 0 8 Reserved 0

1 Signal T ransmission level Binary input 0 2 (0~-31 dBm setting by 1dBm step) No. = 16 8 4 2 1 1 3 1 2 3 4 5 0

4 0 1 0 1 0 1

5 0

6 Protocol monitor(Error print) Printed at com. error Not printed 0 7 Protocol monitor Yes No 0

8 Line monitor Yes No 0

Digital equalization setting(Reception) 7.2km 0km

1No. 1101 2No. 2101

Digital equalization setting(Transmitter) 7.2km 0km

3No. 3100

4No. 4100

Digital equalization setting(Reception 7.2km 0km

5 for Caller ID) No. 5 1 0 0 6 No. 6 1 0 0

7 Error criterion 10 ~ 20 % 5 ~ 10 % 0 8 Anti junk fax check Yes No 1

ITEM

Switch setting and function

Receive:1.5m

9600bps 7200bps 4800bps 2400bps

Initial

setting

Remarks

2 – 5

FO-77U UX-66U

NO.

DA TA

NO.

1 Auto gain control(MODEM) Enable Disable 1 2 End Buzzer Yes No 1 3 Disconnect the line when DIS is received in No Yes 1

RX mode

4 Equalizer freeze control(MODEM) On Off 0

5 Equalizer freeze control 7200 bps only No Yes 0 6 CNG transmission in manual TX mode Yes No 1

7 Initial compression scheme for sharp fax in MR mode H2 mode 0

TX mode

8 Modem speed automatic down when RX Yes No 0

level is under -40dBm EOL detect timer 5 seconds 13 seconds 20 seconds25 seconds

1 No. 100110 2 No. 201011 3 Reserved 0

4 Reserved 0 5 Reserved 0

6 Reserved 0 7 Reserved 0

8 Reserved 0 1 Hold key Enable Disable 1 2 Auto dial fax transmission by REDIAL key Yes No 0

3 Reserved 0 4 Recall interval Binary input 0

5 (0~15.5min setting by 0.5min step) No. = 16 8 4 2 1 1 6 4 5 6 7 8 0 7 0 1 0 1 0 1 8 0 1 Recall times(0~15times setting) Binary input 0 2 No. = 8 4 2 1 0

3 1 2 3 4 1 4 0 0 1 0 0

5 Dial tone detection(Before auto dial) No Yes 1 6 Reserved 0

7 Busy tone detection(After auto dial) No Yes 0 8 Busy tone detection pulse number 4 pulses 2 pulses 0

(After auto dial)

Waiting time after dialing

1 No. 100110 2 No. 201010 3 Reserved 0 4 Reserved 0

5 Reserved 0 6 Reserved 0 7 Reserved 0

8 Reserved 0 1 Dial pausing(sec/pause) 4 sec 2 sec 0

2 Dial mode Tone Pulse 1 OPTION 3 Pulse → Tone change function by key Enable Disable 0

4 Dial pulse make/break ratio(%) 40/60 33/67 1

Auto dial mode Delay timer of before line

5 connect No. 5 0 0 1 1 0 6No. 601010 7 Reserved 0

8 Reserved 0

ITEM

Switch setting and function

45 seconds 55 seconds 90 seconds 140 seconds

0 second 1.5 seconds 3.0 seconds 4.5 seconds

Initial

setting

Remarks

2 – 6

FO-77U UX-66U

DA TA

NO.

Auto dial mode Delay timer of after line 1.7s 2.0s 2.5s 3.0s 3.6s 4.0s 5.5s 7.0s

1 connect No. 1 0 0 0 0 1 1 1 1 0 2 No. 200110011 0 3 No. 301010101 0

Fax signal detection after telephone mode dial

Recalling fixed only one time when dialing was

unsuccessful without detecting busy tone signal 6 Reserved 0 7 Reserved 0

8 Reserved 0 1 DTMF signal transmission level Binary input 0

2 (Low frequency 0~15.5dBm setting No. = 16 8 4 2 1 1 3 by 0.5dBm step) 1 2 3 4 5 1

4 0 1 1 0 0 0 5 0

6 Reserved 0 7 Reserved 0

8 Reserved 0 1 DTMF signal transmission level Binary input 0 2 (High frequency 0~15.5dBm setting No. = 16 8 4 2 1 1 3 by 0.5dBm step) 1 2 3 4 5 0

4 0 1 0 0 1 0 5 1

6 Reserved 0 7 Reserved 0

8 Reserved 0

Reading Slice(Binary) Factory Dark Light Daker in

1 No. 100110 2 No. 201010

Reading Slice(Half tone) Factory Dark Light Daker in

3 No. 300110 4 No. 401010 5 Line density selection Fine Standard 0 6 Reserved 0

7 MTF correction in half tone mode No Yes 0 8 Reserved 0

1 Number of rings for auto receive Binary input 0 OPTION 2 (0~15rings setting) No. = 8 4 2 1 1 3 1 2 3 4 0

4 0 1 0 0 0 5 Automatic swiching manual to auto receive Yes No 0

function

CI detect frequency 6 No. 600110

7 No. 701010 8 Reserved 0

ITEM

Yes No 0 Yes No 1

Switch setting and function

setting dark

As PTT 11.5Hz 13.0Hz 20.0Hz

Initial

setting

Remarks

2 – 7

FO-77U UX-66U

NO.

DA TA

NO.

Distinctive ringing setting USA/ USA/ USA/ USA/ OPTION

1 No. 10000111 0 2 No. 20011001 0 3 No. 30101010 0

4 Reserved 0 5 Reserved 0 6 Caller ID function Yes No 0 OPTION 7 Reserved 0 8 Reserved 0 1 CI off detection timer Binary input 0 2 (0~1550ms setting by 50ms step) No. = 16 8 4 2 1 1 3 1 2 3 4 5 1

4 0 1 1 1 0 1

5 0 6 Reserved 0 7 Reserved 0 8 Reserved 0 1 DTMF type Caller ID RX level Binary input 1 2 (0~-44dBm setting by 1dBm step) No. = 32 16 8 4 2 1 0 3 1 2 3 4 5 6 1

4 1 0 1 1 0 0 1

5 0 6 0

7 Reserved 0 8 Reserved 0 1 Reserved 0

2 Reserved 0 3 Reserved 0

4 Reserved 0

5 Reserved 0 6 Reserved 0

7 Reserved 0 8 Reserved 0

1 Reserved 0 2 Reserved 0

3 Reserved 0 4 Reserved 0

5 Reserved 0 6 Reserved 0

7 Reserved 0 8 Reserved 0

1 Reserved 0 2 Reserved 0

3 Reserved 0 4 Reserved 0

5 Reserved 0 6 Reserved 0

7 Reserved 0 8 Reserved 0

ITEM

OFF Std. Pat.1 Pat.2 Pat.3 Pat.4 Pat.5

Switch setting and function

Canada Canada Canada Canada Canada Canada

Initial

setting

Remarks

2 – 8

FO-77U UX-66U

DA TA

NO.

DTMF detection time 50ms 80ms 100ms 120ms 1 No. 100110 2 No. 201010

3 Protection of remote reception(5 )Yes No 1

detection 4 Remote reception with GE telephone Compatible Not compatible 1 5 Remote operation code figure by external Binary input 0

6 TEL (0~9) No. = 8 4 2 1 1 7 5 6 7 8 0

8 0 1 0 1 1 1 CNG detection in STAND-BY mode Yes No 0

Number of CNG detect(AM mode) 1 pulse 2 pulses 3 pulses 4 pulses 2 No. 200110 3 No. 301011

Number of CNG detect(STAND-BY mode) 1 pulse 2 pulses 3 pulses 4 pulses 4 No. 400110 5 No. 501011

6 Reserved 0 7 Reserved 0

8 Reserved 0 1 Reserved 0

2 Reserved 0 3 Reserved 0

4 Reserved 0 5 Reserved 0

6 Reserved 0 7 Reserved 0

8 Reserved 0 1 Reserved 0

2 Reserved 0 3 Reserved 0

4 Reserved 0 5 Reserved 0

6 Reserved 0 7 Reserved 0

8 Reserved 0 1 Reserved 0

2 Reserved 0 3 Reserved 0

4 Reserved 0 5 Reserved 0

6 Reserved 0 7 Reserved 0 8 Reserved 0

1 Reserved 0 2 Reserved 0

3 Reserved 0 4 Reserved 0

5 Reserved 0 6 Reserved 0

7 Reserved 0 8 Reserved 0

ITEM

Switch setting and function

Initial

setting

Remarks

2 – 9

FO-77U UX-66U

NO.

DA TA

NO.

1 Reserved 0 2 Reserved 0 3 Reserved 0

4 Reserved 0

5 Reserved 0 6 Reserved 0

7 Reserved 0 8 Reserved 0 1 Reserved 0 2 Reserved 0 3 Reserved 0

4 Reserved 0

5 Reserved 0 6 Reserved 0

7 Reserved 0 8 Reserved 0 1 Reserved 0 2 Reserved 0 3 Reserved 0

4 Reserved 0

5 Reserved 0 6 Reserved 0

7 Reserved 0 8 Reserved 0 1 Reserved 0 2 Reserved 0 3 Reserved 0

4 Reserved 0

5 Reserved 0 6 Reserved 0

7 Reserved 0 8 Reserved 0 1 Reserved 0 2 Reserved 0

3 Reserved 0 4 Reserved 0

5 Reserved 0 6 Reserved 0

7 Reserved 0 8 Reserved 0

1 Reserved 0 2 Reserved 0

3 Reserved 0 4 Reserved 0

5 Reserved 0 6 Reserved 0

7 Reserved 0 8 Reserved 0

ITEM

Switch setting and function

Initial

setting

Remarks

2 – 10

FO-77U UX-66U

DA TA

NO.

1 Reserved 0 2 Reserved 0

3 Reserved 0

4 Reserved 0

5 Reserved 0

6 Reserved 0 7 Reserved 0

8 Reserved 0 1 Reserved 0

2 Reserved 0 3 Reserved 0

4 Reserved 0

5 Reserved 0

6 Reserved 0 7 Reserved 0

8 Reserved 0 1 Reserved 0

2 Reserved 0 3 Reserved 0

4 Reserved 0

5 Reserved 0

6 Reserved 0 7 Reserved 0

8 Reserved 0 1 Reserved 0

2 Reserved 0 3 Reserved 0

4 Reserved 0

5 Reserved 0

6 Reserved 0 7 Reserved 0

8 Reserved 0 1 Sender’s phone number setting Cannot change Change allowed 0 2 Summer time setting (Daylight saving) No Yes 1 OPTION

Ringer volume Off Low Middle High OPTION 3 No. 300111

4 No. 401010

Speaker volume Low Low Middle High OPTION 5 No. 500111

6 No. 601010 7 Reserved 0

8 Reserved 0

Handset receiver volume Middle Middle Middle High OPTION 1 No. 100111

2 No. 201010 3 Reserved 0 4 Reserved 0 5 Reserved 0

6 Reserved 0 7 Reserved 0

8 Reserved 0

ITEM

Switch setting and function

Initial

setting

Remarks

2 – 11

FO-77U UX-66U

NO.

DA TA

NO.

Communication results printout Err/Tmr/M Send only Always No print (Transaction report)

1 2 No. 200111 3 No. 301011

4 Time format 12 hour 24 hour 1 5 Date format Month-Day-Year Day-Month-Year 1 6 Reserved 0

7 Reserved 0 8 Reserved 0

1 Entering diag mode by pressing SPEED key Yes No 0 2 Reserved 0 3 Reserved 0

4 Reserved 0

5 Reserved 0 6 Reserved 0

7 Reserved 0 8 Reserved 0

ITEM

No. 100000

Switch setting and function

Initial

setting

Remarks

2 – 12

• Soft switch function description

SW-A1 No. 1 Protect from echo

Used to protect from echo in reception.

SW-A1 No. 2 Forced 4800BPS reception

When line conditions warrant that receptions take place at 4800 BPS repeatedly. It may improve the success of receptions by setting at 4800BPS. This improves the receiving document quality and reduces handshake time due to fallback during training.

SW-A1 No. 3 Footer print

When set to "1", the date of reception, the sender machine No., and the page No. are automatically recorded at the end of reception.

SW-A1 No. 4 Length limitation of copy/send/receive

Used to set the maximum page length. To avoid possible paper jam, the page length is normally limited to 0.6 meter for copy or transmit, and 1.5 meters for receive. It is possible to set it to "No limit" to transmit a long document, such as a computer print form, etc. (In this case, the receiver must also be set to no limit.)

SW-A1 No. 5 CSI transmission

(CSI TRANSMISSION) is a switch to set whether the machine sends or does not send the signal (CSI signal) informing its own telephone No. to the remote fax machine when information is received. When "nonsending" is set, the telephone No. is not output on the remote transmitting machine if the remote transmitting machine has the function to display or print the telephone No. of receiving machine, using this CSI signal.

SW-A1 No. 6 DIS receive ac kno wledgment during G3 transmission

Used to make a choice of whether reception of DIS(NSF) is acknowledged after receiving two DISs(NSFs) or receiving one DIS (two NSFs). It may be useful for ov erseas communication to a v oid an echo suppression problem, if set to 1.

SW-A1 No. 7 Non modulated carrier for V29 transmission mode

Though transmission of a nonmodulated carrier is not required for transmission by the V29 modem according to the CCITT Recommendation, it may be permitted to a send nonmodulated carrier before the image signal to avoid an echo suppression problem. It may be useful for ov erseas communication to a v oid an echo suppression problem, if set to 1.

SW-A1 No. 8 Reserved

Set to "1".

SW-A2 No. 1 ~ No. 4 Modem speed

Used to set the initial modem speed. The default is 9600BPS. It may be necessary to program it to a slower speed when frequent line fallback is encountered, in order to save the time required for fallback procedure.

SW-A2 No. 5 Reserved

Set to "1".

SW-A2 No. 6 H2 mode

Used to determine reception of H2 mode (15 sec transmission mode). When set to OFF, H2 mode reception is inhibited even though the transmitting machine has H2 mode function.

SW-A2 No. 7 Comm unication error treatment in R TN sending mode (Reception )

Used to determine communication error treatment when RTN is sent by occurrence of a received image error in G3 reception. When it is set to "1", communication error is judged as no error.

SW-A2 No. 8 CNG transmission

When set to "0", this model allows CNG transmission by pressing the Start key in the key pad dialing mode. When set to "1", CNG transmission in the key pad dialing mode cannot be performed. In either case, CNG transmission can be performed in the auto dial mode.

FO-77U UX-66U

SW-A3 No. 1, No. 2 CED tone signal interval

For international communication, the 2100Hz CED tone may act as an echo suppression switch, causing a communication problem. Though SW-A3 No. 1 and No. 2 are normally set to 0, this selfing is used to change the time between the CED tone signal to eliminate the communication caused by echo.

TX RX

CED

DIS

SW-A3 No. 3 MR coding

Used to select the MR coding enable or disable.

SW-A3 No. 4 ~ No. 8 Reserved

Set to "0".

SW-A4 No. 1 ~ No. 5 Signal transmission level (0~-31 dBm setting by 1dBm step)

Used to control the signal transmission level in the range of -0dB to

-31dB. The factory setting is at -10dB (MODEM output).

SW-A4 No. 6 Protocol monitor (Error Print)

If set to "1", protocol is printed at communication error.

SW-A4 No. 7 Protocol monitor

Normally set to "0". If set to "1", communication can be check ed, in case of trouble, without using a G3 tester or other tools. When communication FSK data transmission or reception is made, the data is taken into the buffer . When communication is finished, the data is analyzed and printed out. When data is received with the line monitor (SW4-No. 8) set to "1" the reception level is also printed out.

SW-A4 No. 8 Line monitor

Normally set to "0". If set to "1", the transmission speed and the reception level are displayed on the LCD. Used for line tests.

SW-A5 No. 1, No. 2 Digital equalization setting (Reception)

Line equalization when reception is to be set according to the line characteristics. Setting should be made according to distance between the telephone and the telephone company central switching station.

SW-A5 No. 3, No. 4 Digital equalization setting (Transmitter)

Line equalization when transmission is to be set according to the line characteristics. Setting should be made according to distance between the telephone and the telephone company central switching station.

2 – 13

FO-77U UX-66U

SW-A5 No. 5, No. 6 Digital equalization setting (Reception for Caller ID)

Line equalization when reception for CALLER ID is to be set according to the line characteristics. Setting should be made according to distance between the telephone and the telephone company central switching station.

SW-A5 No. 7 Error criterion

Used to select error criterion for sending back RTN when receiving image data.

SW-A5 No. 8 Anti junk fax check

When using the Anti junk fax function, set to "1".

SW-A6 No. 1 Auto gain control(MODEM)

When this mode is enabled, if the reception signal level is under 31dBm, the modem itself controls the signal gain automatically.

SW-A6 No. 2 End buzzer

Setting this bit to 0 will disable the end buzzer (including the error buzz er/ on-hook buzzer).

SW-A6 No. 3 Disconnect the line when DIS is received in RX mode

Bit1 = 0 : When DIS signal is receiv ed during RX mode, disconnect the

line immediately.

Bit1 = 1 : When DIS signal is receiv ed during RX mode, w ait for the ne xt

signal.

SW-A6 No. 4 Equalizer freeze contr ol (MODEM)

This switch is used to perform reception operation by fixing the equalizer control of modem for the line which is always in unfavorable state and picture cannot be received. * Usually , the control is ex ecuted according to the state of line where the equalizer setting is changed always.

SW-A6 No.5 Equalizer freeze 7200BPS only

Setting which specifies SW-A6 No . 4 control only in condition of 7200BPS modem speed.

SW-A6 No. 6 CNG transmission in manual TX mode

When set to "1", fax transmit the CNG signal in case of manual transmissiom mode (User press the START key after waiting for the fax answering signal from handset or speaker).

SW-A6 No. 7 Initial compression scheme for sharp fax in TX mode

When set to "0", if the other fax is Sharp model, fax transmit the document by H2 mode. When set to "1", even if the other fax is Sharp model, fax transmit the document by MR mode.

SW-A6 No. 8 Modem speed automatic do wn when RX level is under

-40dBm

When set to "1", if fax signal level is under -40dBm during reception, machine selects the slower modem speed automatically. It is effective when noises occur on the received document due to the long distance communications.

SW-A7 No. 1, No. 2 EOL (End Of Line) detect timer

Used to make a choice of whether to use the 5 or 13 or 20 or 25 seconds timer for detection of EOL. This is effective to override communication failures with some facsimile models that have longer EOL detection.

SW-A7 No. 3 ~ No. 8 Reserved

Set to "0".

SW-B1 No. 1 Hold key

Used to set YES/NO of holding function by the HOLD key.

SW-B1 No. 2 Auto dial fax transmission by REDIAL key

When set to "1", if original documents are set to the feeder and you press REDIAL key, machine will dial and transmit the ducuments automatically. When set to "0", operator needs to press the START key after FAX reception tone is heard.

SW-B1 No. 3 Reserved

Set to "0".

SW-B1 No. 4 ~ No. 8 Recall interval (0~15.5min setting by 0.5min step)

Choice is made for a redial interval for speed and rapid dial calls. Use a binary number to program this with 0.5min steps. If set to 0 accidentally, 0.5min will be assumed.

SW-B2 No. 1 ~ No.4 Recall times (0~15times setting)

Choice is made as to how many redials there should be.

SW-B2 No. 5 Dial tone detection (Before auto dial)

Used to set YES/NO of dial tone detection in auto dialing.

SW-B2 No. 6 Reserved

Set to "0".

SW-B2 No. 7 Busy tone detection (After auto dial)

Used to set YES/NO of busy tone detection after auto dialing.

SW-B2 No. 8 Busy tone detection pulse number (After auto dial)

Used for detection of busy tone in 2 or 4 pulses.

SW-B3 No. 1, No. 2 Waiting time after dialing

This is waiting time for the opponent's signals after dialing. 45 / 55 / 90 / 140 seconds settings are available.

SW-B3 No. 3 ~ No. 8 Reserved

Set to "0".

SW-B4 No. 1 Dialing pause (sec/pause)

Pauses can be inserted between telephone numbers of direct dial connection. Selection of 4 sec or 2 sec pause is available.

SW-B4 No. 2 Dial mode

When using the pulse dial, set to 0. When using the tone dial, set to 1.

SW-B4 No. 3 Pulse → Tone change function by key

When setting to 1, the mode is changed by pressing the k ey from the pulse dial mode to the tone dial mode.

SW-B4 No. 4 Dial pulse make/break ratio (%)

When using the 33% make ratio pulse dial, set to 0. When using the 40% make ratio pulse dial, set to 1.

SW-B4 No. 5, No. 6 Auto dial mode Delay timer of before line connect

Delay time between the dial key input and line connection under the auto dial mode.

RAPID A CML RELAY ON

DIALLING

No.5=0 No.6=0 : 0sec No.5=0 No.6=1 : 1.5sec No.5=1 No.6=0 : 3.0sec No.5=1 No.6=1 : 4.5sec

SW-B4 No. 7, No. 8 Reserved

Set to "0".

2 – 14

SW-B5 No. 1 ~ No. 3 Auto dial mode Delay timer of after line connect

Delay time between the line connection and dial data output under the auto dial mode. This setting is available when dial tone detection(SW -B2 No. 5) is set to "NO".

RAPID A CML RELAY ON

No. 1 No. 2 No. 3

0 0 0 1.7sec 0 0 1 2.0sec 0 1 0 2.5sec 0 1 1 3.0sec 1 0 0 3.6sec 1 0 1 4.0sec 1 1 0 5.5sec 1 1 1 7.0sec

SW-B5 No. 4 Fax signal detection after telephone mode dial

When set to "1", if machine detects the fax answering signal after telephone calling (handset off-hook or speaker mode dial), machine starts to receive the documents automatically.

SW-B5 No. 5 Recalling fixed only one time when dialing was unsuccessful without detecting busy tone signal

When set to "1", if machine does not detect the busy tone after auto dialing and dialing is unsuccessful, machine will try to recall only one time.

SW-B5 No. 6 ~ No. 8 Reserved

Set to "0".

SW-B6 No. 1 ~ No. 5 DTMF signal transmission level (Low frequency 0~15.5dBm setting by 0.5dBm step)

The transmission level of DTMF signal is adjusted. (lower frequency)

00000: 0dBm

↓

11111: -15.5 dBm (-0.5dBm x 31)

SW-B6 No. 6 ~ No. 8 Reserved

Set to "0".

SW-B7 No. 1 ~ No. 5 DTMF signal transmission level (High frequency 0~15.5dBm setting by 0.5dBm step)

The transmission level of DTMF signal is adjusted. (higher frequency)

00000: 0dBm

↓

11111: -15.5 dBm (-0.5dBm x 31)

SW-B7 No. 6 ~ No. 8 Reserved

Set to "0".

SW-C1 No. 1, No. 2 Reading slice (Binary)

Used to determine the set value of reading density in standard/fine/super-fine mode. The standard setting is "00"(Factory setting is "00").

SW-C1 No. 3, No. 4 Reading slice (Half tone)

Used to determine the set value of reading density in half tone mode. The standard setting is "00"(Factory setting is "00").

DIAL DATA

FO-77U UX-66U

SW-C1 No. 5 Line density selection

Used to set the transmission mode which is automatically selected when the Resolution key is not pressed. In the copy mode, however, the fine mode is automatically selected unless the Resolution key is manually set to another mode.

SW-C1 No. 6 Reserved

Set to "0".

SW-C1 No. 7 MTF correction in half tone mode

This allows selection of MTF correction (dimness correction) in the half tone mode. When "NO" (=1) is selected, the whole image becomes soft and mild. Clearness of characters will be reduced. Normally set to "YES" (=0).

SW-C1 No. 8 Reserved

Set to "0".

SW-D1 No.1 ~ No. 4 Number of rings for auto receive (0~15rings setting)

When the machine is set in the auto receive mode, the number of rings before answering can be selected. It may be set from one to nine rings using a binary number. Since the facsimile telephone could be used as an ordinary telephone if the handset is taken off the hook, it should be programmed to the user's choice. If the soft switch was set to 1, direct connection is made to the facsimile. If a facsimile calling beep was heard when the handset is taken off the hook, press the ST AR T ke y and put the handset on the hook to hav e the facsimile start receiving. If it was set to 0 accidentally, receive ring is set to 1.

NOTE: If the machine is set to answer after a large number of rings, it

may not be able to receive faxes successfully. If you have difficulty receiving f axes , reduce the number of rings to a maximum of 5.

SW-D1 No. 5 Automatic switching manual to auto receive function

This soft switch is used to select whether the machine should switch to the auto receive mode after 5 rings in the manual receive mode or remain in the same way as SW -D1 No. 1, No . 2, No . 3 and No. 4 "0"1"0"1"(5 rings).

SW-D1 No. 6, No. 7 CI detect frequency

Detection frequency of ring signal for auto reception is set. When set to No. 6=0, No. 7=0,frequency is set to PTT recommendation.

When set to No. 6=0, No. 7=1, frequency is set to 11.5Hz or more. When set to No. 6=1, No. 7=0, frequency is set to 13.0Hz or more. When set to No. 6=1, No. 7=1, frequency is set to 20.0Hz or more.

SW-D1 No. 8 Reserved

Set to "0".

2 – 15

FO-77U UX-66U

SW-D2 No. 1 ~ No. 3 Distinctive ringing setting

When the ringing setting is turned off, all of the CI signals are received. When any of the standard, and ring patterns 1 through 3 is selected for the ringing setting, only the selected CI signal is received. CI signal patterns

The CI signal patterns consists of the standard pattern, and ring patterns 1 through 7. The standard pattern is the conventional one.

SW-D3 No. 1 ~ No. 5 CI off detection timer (0~1550ms setting by 50ms step)

Set the minimum time period of CI signal interruption which affords to be judged as a CI OFF section with 50ms steps. (Example)

STANDARD

1.5S

0.5S

0.8S

0.4S 1S

RING

PATTERN 1

for USA

0.8S

0.2S

0.4S 0.8S

0.5S

0.3S

1S 0.5S

0.5S0.5S

RING

PATTERN 2

for USA

RING

PATTERN 3

for USA

RING PATTERN 1 for CANADA

RING PATTERN 2 for CANADA

RING PATTERN 3 for CANADA

0.3S

0.2S

0.4S

0.2S 0.2S

0.5S

SW-D2 No. 4, No. 5 Reserved

Set to "0".

SW-D2 No. 6 Caller ID Function

Used for Caller ID function.

SW-D2 No. 7, No. 8 Reserved

Set to "0".

3.5S

400msec

2000msec

0 1 1 1 0 (50ms~14) : 700ms(CI interruption>700ms:Judged as a CI

OFF section) The section 1 is not judged as a CI OFF section, the CI signal A is counted as one signal. The section 2 is judged as a CI OFF section, the CI signal B is considered as the second signal.

0 0 1 1 1 (50ms~7) : 350ms(CI interruption>350ms:J udged as a CI

OFF section) The section 1 is judged as a CI OFF section, and the CI signal A is counted as two signals. The section 2 is judged as a CI OFF section, and the CI signal B is considered as the third signal.

SW-D3 No. 6 ~ No. 8 Reserved

Set to "0".

SW-D4 No. 1 ~ No. 6 DTMF type Caller ID RX level (0~-44dBm setting by 1dBm step)

This is used for DTMF type Caller ID detection level setting.

SW-D4 No. 7, No. 8 Reserved

Set to "0".

SW-E1 No. 1 ~ No. 8 Reserved

Set to "0".

SW-E2 No. 1 ~ No. 8 Reserved

Set to "0".

SW-E3 No. 1 ~ No. 8 Reserved

Set to "0".

SW-F1 No. 1, No. 2 DTMF detection time

Used to set detect time of DTMF (Dual Tone Multi Frequency) used in remote reception(5 ). The longer the detect time is, the less the error detection is caused by noises.

SW-F1 No. 3 Protection of remote reception (5 ) detection

Used to set the function of remote reception (5 ). When set to "1", the remote reception function is disabled.

SW-F1 No. 4 Remote reception with GE telephone

"1": Compatible with TEL mode by GE "0": Not compatible

• When sending (5 ) for remote reception with a GE manufactured telephone remote reception may not take place because of special specifications in their DTMF.

To overcome this, a soft SW is provided to change the modem setting

to allow for remote reception.

• If this soft SW is set to "1", other telephone sets may be adversely affected.

SW-F1 No. 5 ~ No. 8 Remote operation code figure by external TEL (0~9)

Remote operation codes can be changed from 0 through 9. If set to greater than 9, it defaults to 9. The "5 " is not changed. Ex- 7 (Default : 5 )

2 – 16

SW-F2 No. 1 CNG detection in STAND-BY mode

When setting to "1", the CNG signal detection function during standby stops.

SW-F2 No. 2, No. 3 Number of CNG detect (AM mode)

Used for detection of CNG in 1 to 4 pulses.

SW-F2 No. 4, No. 5 Number of CNG detect (STAND-BY mode)

Used for detection of CNG in 1 to 4 pulses.

SW-F2 No. 6 ~ No. 8 Reserved

Set to "0"

SW-G1 No. 1 ~ No. 8 Reserved

Set to "0"

SW-G2 No. 1 ~ No. 8 Reserved

Set to "0"

SW-G3 No. 1 ~ No. 8 Reserved

Set to "0".

SW-G4 No. 1 ~ No. 8 Reserved

Set to "0".

SW-H1 No. 1 ~ No. 8 Reserved

Set to "0".

SW-H2 No. 1 ~ No. 8 Reserved

Set to "0".

SW-I1 No. 1 ~ No. 8 Reserved

Set to "0".

SW-I2 No. 1 ~ No. 8 Reserved

Set to "0".

SW-I3 No. 1 ~ No. 8 Reserved

Set to "0".

SW-I4 No. 1 ~ No. 8 Reserved

Set to "0".

SW-I5 No. 1 ~ No. 8 Reserved

Set to "0".

SW-I6 No. 1 ~ No. 8 Reserved

Set to "0".

SW-I7 No. 1 ~ No. 8 Reserved

Set to "0".

SW-I8 No. 1 ~ No. 8 Reserved

Set to "0".

SW-J1 No. 1 Sender's phone number setting

Used to make a choice of whether the registered sender's phone number can be changed or not. If the switch is set to "1", new registration of the sender's phone number is disabled to prevent accidental wrong input.

SW-J1 No. 2 Summer time setting (Daylight saving)

Used to set YES/NO of automatic clock adjustment for Summer time(Daylight saving time).

SW-J1 No. 3, No. 4 Ringer Volume

Used to adjust ringing volume.

SW-J1 No. 5, No. 6 Speaker Volume

Used to adjust sound volume from a speaker.

SW-J1 No. 7, No. 8 Reserved

Set to "0".

SW-J2 No. 1, No. 2 Handset receiver volume

Used to adjust sound volume from a handset receiver volume.

FO-77U UX-66U

SW-J2 No. 3 ~ No. 8 Reserved

Set to "0".

SW-J3 No. 1 ~ No. 3 Communication results printout (Transaction report)

It is possible to obtain transaction results after each communication. Normally,the switch is set (No. 1 : 0, No. 2 : 0, No. 3 : 0) so that the transaction report is produced only when a communication error is encountered. If No.1 was set to 0 and No. 2 to 1 and No. 3 to 0, the transaction report will be produced every time a communicaion is done, even if the communicaion was successful. Setting No. 1 to 0 and No . 2 to 1 and No. 3 to 1 will disable this function. No transaction report printed.

SW-J3 No. 4 Time format

When set to "0", 24hour time format is used. When set to "1", 12hour time format is used.

SW-J3 No. 5 Date format

When set to "0", Day-Month-Year format is used. When set to "1", Month-Day-Year format is used.

SW-J3 No. 6 ~ No. 8 Reserved

Set to "0".

SW-K1 No. 1 Entering diag mode by pressing SPEED key

A bit which is used in the production process only . When the SPEED key is pressed, the switch is changed from the stand-by state to the diag mode.

SW-K1 No. 2 ~ No. 8 Reserved

Set to "0".

2 – 17

FO-77U

UX-66U

[3] T roubleshooting

Refer to the following actions to troub leshoot any of the problems mentioned in 1-4.

[1] A communication error occurs. [2] Image distortion produced. [3] Unable to do overseas communication. [4] Communication speed slow due to FALLBACK.

• Increase the transmission level SOFT SWITCH A4-1, 2, 3, 4, 5.

May be used in case [1] [2] [3].

• Decrease the transmission level SOFT SWITCH A4-1, 2, 3, 4,

5. May be used in case [3].

TO: ATT: Ref.No.: CC: ATT: Date : FM: Dept :

***** Facsimile communication problem ***** From: Mr. Fax Tel No.: Our customer Name Tel No.

Address Fax No. Contact person Model name

Other party Name Tel No.

Address Fax No. Contact person Model name

Problem mode Line: Domestic / international Model: G3 Phase: A, B, C, D.

Reception / Transmission

Frequency: % ROM version: Confirmation

item

Our customer

Automatic reception / Manual reception Automatic dialing / Manual dialing / Others

B1 B2

• Apply line equalization SOFT SWITCH A5-1, 2.

May be used in case [1] [2] [3] [4].

• Slow down the transmission speed SOFT SWITCH A2-1, 2, 3,

4. May be used in case [2] [3].

• Replace the TEL/LIU PWB.

May be used in all cases.

• Replace the control PWB.

May be used in all cases.

* If transmission problems still exist on the machine, use the following

format and check the related matters.

Sign :

Other party

Please mark problem with an X. No problem is: 0.

A1 A2 B1 B2 C1 C2 D1 D2 E1 E2

Ref.No.: Date:

A1 A2

C1 D2

C2 D1

E1 E2

Our service

Comment

Countermeasure

**** Please attach the G3 data and activity report on problem. ****

* Please complete this report before calling the “TAC” hotline if problem still occurs.

Other part

's service

Transmission level setting is ( ) dB at our customer Transmission level ( ) dBm Reception level ( ) dBm By level meter at B1 and B2

2 – 18

+ 68 hidden pages