Sharp PG-LW2000 User Manual

Download

DATA PROJECTOR

MODEL

PG-LW2000

Introduction Easy Start Setup

OPERATION MANUAL

Connections

Operation

Basic

Features

Useful

Appendix

IMPORTANT

• For your assistance in reporting the loss or theft of your Projector, please record the Model and Serial Number located on the bottom of the projector and retain this information.

• Before recycling the packag ing, please ensure that you have checked the contents of the carton thoroughly against the list of “Supplied accessories” on page

SPECIAL NOTE FOR USERS IN THE U.K.

The mains lead of this product is ﬁ tted with a non-rewireable (moulded) plug incorporating a 10A fuse. Should the fuse need to be replaced, a BSI or ASTA approved BS 1362 fuse marked of the plug, must be used. Always reﬁ t the fuse cover after replacing the fuse. Never use the plug without the fuse cover ﬁ tted. In the unlikely event of the socket outlet in your home not being compatible with the plug supplied, cut off the mains plug and ﬁ t an appropriate type.

DANGER:

The fuse from the cut-off plug should be removed and the cut-off plug destroyed immediately and disposed of in a safe manner. Under no circumstances should the cut-off plug be inserted elsewhere into a 13A socket outlet, as a serious electric shock may occur. To ﬁ t an appropriate plug to the mains lead, follow the instructions below:

WARNING:

THIS APPARATUS MUST BE EARTHED.

IMPORTANT:

The wires in this mains lead are coloured in accordance with the following code:

As the colours of the wires in the mains lead of this apparatus may not correspond with the coloured markings identifying the terminals in your plug proceed as follows:

The wire which is coloured green-and-yellow must be connected to the terminal in the

•

The wire which is coloured blue must be connected to the terminal which is marked

•

The wire which is coloured brown must be connected to the terminal which is marked

•

or and of the same rating as above, which is also indicated on the pin face

Green-and-yellow : Earth Blue : Neutral Brown : Live

plug which is marked by the letter E or by the safety earth symbol or green-and-yellow.

with the letter N or coloured black.

with the letter L or coloured red.

Model No.:

Serial No.:

or coloured green

IF YOU HAVE ANY DOUBT, CONSULT A QUALIFIED ELECTRICIAN.

Authorized representative responsible for the European Union Community Market

SHARP ELECTRONICS (Europe) GmbH Sonninstraße 3, D-20097 Hamburg

E.U. ONLY

Before using the projector, please read this operation manual carefully.

Introduction

ENGLISH

There are two important reasons for prompt warranty registration of your new SHARP Projec tor, using the REGISTRATION CARD packed with the projector.

1. WARRANTY

This is to assure that you immediately receive the full beneﬁ t of the parts, service and labor warranty applicable to your purchase.

2. CONSUMER PRODUCT SAFETY ACT

To ensure that you will promptly receive any safety notiﬁ cation of inspection, modiﬁ cation, or recall that SHARP may be required to give under the 1972 Consumer Product Safety Act, PLEASE READ CAREFULLY THE IMPORTANT “LIMITED WARRANTY” CLAUSE.

WARNING:

High brightness light source. Do not stare into the beam of light, or view directly. Be especially careful that children do not stare directly into the beam of light.

To reduce the risk of ﬁ re or electric shock, do not

U.S.A . ONLY

expose this product to rain or mois ture.

See bottom of projector.

CAUTION

RISK OF ELECTRIC SHOCK.

DO NOT REMOVE SCREWS

EXCEPT SPECIFIED USER

SERVICE SCREW.

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,

NO USER-SERVICEABLE PARTS EXCEPT LAMP UNIT.

DO NOT REMOVE COVER.

REFER SERVICING TO QUALIFIED SERVICE

PERSONNEL.

The lightning ﬂ ash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product's enclosure that may be of sufﬁ cient magnitude to constitute a risk or electric shock to persons.

The exclamation point within a triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the product.

WARNING:

This is a Class A product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures.

WARNING:

The enclosed computer cable must be used with the device. The cable is provided to ensure that the device complies with FCC Class A veriﬁ cation.

FCC Regulations state that any unauthorized changes or modiﬁ cations to this equipment not expressly approved by the manufacturer could void the user's authority to operate this equip ment.

U.S.A . ONLY

INFORMATION

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the operation manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference, in which case the user will be required to correct the interference at his own expense.

U.S.A . ONLY

PRODUCT DISPOSAL

This product utilizes lamp containing a small amount of mercury. Disposal of these materials may be regulated due to environmental considerations. For disposal or recycling information, please contact your local authorities, the Electronics Industries Alliance: www.eiae.org, the lamp recycling organization www.lamprecycle.org, or Sharp at 1-800-BE-SHARP.

U.S.A . ONLY

Caution Concerning Lamp Replacement

This projector utilizes a pressurized mercury lamp. A loud sound may indicate lamp failure. Lamp

■

failure can be attributed to numerous sources such as: excessive shock, improper cooling, sur face scratches or deterioration of the lamp due to a lapse of usage time. The period of time up to failure largely varies depending on the individual lamp and/or the condition and the frequency of use. It is important to note that failure can often result in the bulb cracking. When the lamp replacement indicator and on-screen display icon are illuminated, it is recommended

■

that the lamp be replaced with a new one immediately, even if the lamp appears to be operating normally. Should the lamp break, there is also a possibilit y that glass particles may spread inside of the

■

projector. In such a case, it is recommended you contact your nearest Sharp Authorized Projector Dealer or Service Center to assure safe operation. Should the lamp break, the glass particles may spread inside the lamp cage or gas contained in the

■

lamp may be vented into the room from the exhaust vent. Because the gas in this lamp includes mercury, ventilate the room well if the lamp breaks and avoid all exposure to the released gas. In case of exposure to the gas, consult a doctor as soon as possible.

Caution

Do not remove the lamp unit from the projector right after use. The lamp will be very hot and may

• cause burns or injury. Wait at least one hour after the power cord is disconnected to allow the surface of the lamp unit to

• fully cool before removing the lamp unit. Do not touch the glass surface of the lamp unit or the inside of the projector.

• Do not loosen other screws except for the lamp unit cover and lamp unit.

• Make sure to reset the lamp timer only when replacing the lamp. If you reset the lamp timer and

• continue to use the same lamp, this may cause the lamp to become damaged or explode.

Carefully change the lamp by following the instructions described on pages

■

* If you wish, you may have the lamp replaced at your nearest Sharp Authorized Projector

Dealer or Service Center.

* If the new lamp does not light af ter replacement, take your projector to the nearest Sharp Authorized

Projector Dealer or Service Center for repair.

56 to 58.

Accessories

Supplied accessories

Introduction

Two LR03 batteries

(“AAA” size, UM/SUM-4,

Remote control

Power cord*

(1) (2) (3) (4)

For U.S. and Canada, etc.

(6' (1.8 m))

* Which power cords are supplied along with your projector depends on the region. Use the power

cord that corresponds to the wall outlet in your country. Initial setup guide <TINS-F582WJZZ>

• CD-ROM <UDSKAA137WJN1>

•

Note

Codes in “< >” are Replacement parts codes.•

HP-16 or similar)

For Europe, except U.K.

(6' (1.8 m))

For U.K. and

Singapore (6' (1.8 m))

RGB cable

(6' (1.8 m))

For Australia, New

Zealand and Oceania

(6' (1.8 m))

Optional accessories

■ Lamp unit

■ Ceiling-mount adaptor

■ Ceiling-mount bracket

■ Ceiling-mount unit

■ Ceiling-mount extension tube

■ 3 RCA to mini D-sub 15 pin cable (10n (3.0 m))

AN-LX20LP AN-60KT AN-XRCM30 (for U.S.A. only) AN-TK201 <for AN-60KT> AN-TK202 <for AN-60KT> AN-EP101B <for AN-XRCM30> (for U.S.A. only) AN-C3CP2

Note

Some of the optional accessories may not be available depending on the region. Please check with

• your nearest Sharp Authorized Projector Dealer or Service Center.

Preparing

Introduction

Accessories ............................................3

Contents .................................................4

IMPORTANT SAFEGUARDS ..................6

Part Names and Functions ...................10

Top View ................................................ 10

Front View .............................................. 10

Rear View (Terminals) .............................. 11

Inserting the Batteries ............................. 13

Usable Range ......................................... 13

Easy Start

Easy Start .............................................14

Setup and Projection .............................. 14

Setup

Setting Up the Projector .......................16

Video Setup............................................ 16

Setting Up the Projector ......................... 16

Standard Setup (Front Projection) ........... 16

Screen Size and Projection Distance ...... 17

Projection (PRJ) Mode ............................ 18

Ceiling-Mount Setup ............................... 18

Connections

Connecting the Projector to

Other Equipment ................................19

Connecting the Power Cord .................21

Controlling the Projector by

a Computer ........................................22

Using

Basic Operation

Turning the Projector On/Off ................23

Turning the Projector On ......................... 23

Turning the Power Off (Putting the

Projector into Standby Mode) .............. 23

Image Projection ..................................24

About the Setup Guide ........................... 24

Adjusting the Projected Image ................ 24

Correcting Trapezoidal Distortion ............ 26

Switching the Input Mode ....................... 27

Adjusting the Volume .............................. 27

Displaying the Black Screen and

Turning Off the Sound Temporarily ....... 27

Resize Mode .......................................... 28

Useful Features

Operating with the Remote Control......30

Displaying and Setting the

Break Timer ......................................... 30

Displaying the Pointer ............................. 30

Using the Spot Function ......................... 30

Switching the Eco+Quiet Mode .............. 30

Auto Sync (Auto Sync Adjustment) ......... 31

Freezing a Moving Image ........................ 31

Selecting the Picture Mode ..................... 31

Displaying an Enlarged Portion of

an Image ............................................. 31

Menu Items ...........................................32

Using the Menu Screen ........................35

Menu Selections (Quick Start Menu) .........35

Quick Start Menu .................................... 36

Menu Selections (Complete Menu) .......... 36

Picture Adjustment (“Picture” Menu) ....38

Selecting the Picture Mode ..................... 38

Adjusting the Image ................................ 39

Adjusting the Color Temperature ............. 39

Adjusting the Colors ............................... 39

Selecting the Film Mode ......................... 40

Reducing Image Noise (DNR) ................. 40

Eco+Quiet .............................................. 40

Signal Adjustment (“SIG-ADJ” Menu) ..41

Adjusting the Computer Image ............... 41

Resolution Setting .................................. 41

Signal Type Setting ................................. 41

Selecting the Dynamic Range ................. 41

Setting the Video System ....................... 42

Setting the Video Setup .......................... 42

Checking the Input Signal ....................... 42

Adjusting the Projected Image

(“SCR-ADJ” Menu) .............................43

Setting the Resize Mode ......................... 43

Adjusting the Image Position .................. 43

Keystone Correction ............................... 43

Setting the Overscan .............................. 44

Setting the On-screen Display ................ 44

Closed Caption ...................................... 44

Selecting the Background Image ............ 45

Selecting the Setup Guide ...................... 45

Reversing/Inverting Projected Images ..... 45

Selecting the Wall Color .......................... 45

Selecting the On-screen Display Language

Adjusting the Projector Function

(“PRJ-ADJ1/2” Menu) ........................46

Auto Sync (Auto Sync Adjustment) ......... 46

Auto Power Off Function ........................ 46

Auto Restart Function ............................. 46

Speaker Setting ...................................... 46

Fan Mode Setting ................................... 46

System Lock Function ............................ 47

... 45

Keylock Function .................................... 48

Selecting the Quick Start Menu .............. 49

Setting the FUNCTION Button Operation

STANDBY Mode ..................................... 49

DLP

LinkTM ............................................ 49

DLP

LinkTM Invert .................................. 49

Returning to the Default Settings ............ 49

Checking the Lamp Life Status ............... 49

Viewing Stereoscopic 3D Images .........50

Precautions on Viewing Stereoscopic

3D Images ........................................... 50

Information on the 3D Projection

Function .............................................. 51

Appendix ................................................ 51

Using 3D Viewing Mode ......................... 52

Reference

Appendix

Maintenance .........................................53

Maintenance Indicators ........................54

Regarding the Lamp .............................56

Lamp ...................................................... 56

Caution Concerning the Lamp ................ 56

Replacing the Lamp ............................... 56

Removing and Installing the Lamp Unit ... 57

Resetting the Lamp Timer ...................... 58

RS-232C Speciﬁ cations and Commands

Compatibility Chart ..............................64

Troubleshooting ....................................66

For SHARP Assistance .........................69

Speciﬁ cations .......................................70

Dimensions ...........................................71

Index .....................................................72

Introduction

.. 49

...59

In this operation manual, the illustration and the screen display are simpliﬁ ed for explanation, and

• may differ slightly from the actual display.

IMPORTANT SAFEGUARDS

CAUTION: Please read all of these instructions before you operate this

product and save these instructions for later use.

Electrical energy can perform many useful functions. This product has been engineered and manufactured to assure your personal safety. BUT IMPROPER USE CAN RESULT IN POTENTIAL ELECTRICAL SHOCK OR FIRE HAZARDS. In order not to defeat the safeguards incorporated in this product, observe the following basic rules for its installation, use and servicing.

1. Read Instructions

All the safety and operating instructions should be read before the product is operated.

2. Retain Instructions

The safety and operating instructions should be retained for future reference.

3. Heed Warnings

All warnings on the product and in the operating instructions should be adhered to.

4. Follow Instructions

All operating and use instructions should be followed.

5. Cleaning

Unplug this product from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners. Use a damp cloth for cleaning.

6. Attachments

Do not use attachments not recommended by the product manufacturer as they may cause hazards.

7. Water and Moisture

Do not use this product near water–for example, near a bath tub, wash bowl, kitchen sink, or laundry tub; in a wet basement; or near a swimming pool; and the like.

8. Accessories

Do not place this product on an unstable cart, stand, tripod, bracket, or table. The product may fall, causing serious injury to a child or adult, and serious damage to the product. Use only with a cart, stand, tripod, bracket, or table recommended by the manufacturer, or sold with the product. Any mounting of the product should follow the manufacturer's instructions, and should use a mounting accessory recom mended by the manufacturer.

9. Transportation

A product and cart combination should be moved with care. Quick stops, excessive force, and uneven surfaces may cause the product and cart combination to overturn.

10. Ventilation

Slots and openings in the cabinet are provided for ventilation to ensure reliable operation of the product and to protect it from overheating, and these openings must not be blocked or covered. The open ings should never be blocked by placing the product on a bed, sofa, rug, or other similar surface. This prod uct should not be placed in a built-in installation such as a book case or rack unless proper ventilation is provided or the manufacturer's in struc tions have been adhered to.

11. Power Sources

This product should be operated only from the type of power source indicated on the marking label. If you are not sure of the type of power supply to your home, consult your product dealer or local power com pany. For products intended to operate from battery power, or other sources, refer to the operating instructions.

12. Grounding or Polarization

This product is provided with one of the following types of plugs. If the plug should fail to ﬁ t into the power outlet, please contact your electrician. Do not defeat the safety purpose of the plug. a. Two-wire type (mains) plug. b. Three-wire grounding type (mains) plug

with a grounding terminal.

This plug will only ﬁ t into a grounding

type power outlet.

13. Power-Cord Protection

Power-supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them, paying particular attention to cords at plugs, convenience receptacles, and the point where they exit from the product.

14. Lightning

For added protection for this product during a lightning storm, or when it is left unattended and unused for long periods of time, unplug it from the wall outlet and disconnect the cable system. This will pre vent damage to the product due to lightning and power-line surges.

15. Overloading

Do not overload wall outlets, extension cords, or integral convenience receptacles as this can result in a risk of ﬁ re or electric shock.

16. Object and Liquid Entry

Never push objects of any kind into this product through openings as they may touch dangerous voltage points or short-out parts that could result in a ﬁ re or electric shock. Never spill liquid of any kind on the product.

17. Servicing

Do not attempt to service this product yourself as opening or removing covers may expose you to dan ger ous voltage or other hazards. Refer all servicing to qualiﬁ ed service personnel.

18. Damage Requiring Service

Unplug this product from the wall outlet and refer ser vicing to qualiﬁ ed service person nel under the following conditions: a. When the power-supply cord or plug is

damaged.

b. If liquid has been spilled, or objects

have fallen into the product.

c. If the product has been exposed to rain

or water.

d. If the product does not operate normally

by following the operating instructions. Adjust only those con trols that are covered by the operating instructions, as an improper adjustment of other controls may result in damage and will often require extensive work by a qualiﬁ ed technician to restore the product to normal operation.

e. If the product has been dropped or

damaged in any way.

f. When the product exhibits a distinct

change in performance, this indicates a need for service.

19. Replacement Parts

When replacement parts are required, be sure the ser vice technician has used replace ment parts speciﬁ ed by the manufacturer or have the same characteristics as the original part. Unauthorized substitutions may result in ﬁ re, electric shock, or other hazards.

20. Safety Check

Upon completion of any service or repairs to this product, ask the ser vice technician to per form safety checks to determine that the product is in proper operating condition.

21. Wall or Ceiling Mounting

This product should be mounted to a wall or ceiling only as recommended by the manufacturer.

22. Heat

This product should be situated away from heat sources such as radiators, heat registers, stoves, or other products (including ampliﬁ ers) that produce heat.

Introduction

DLP® and the DLP logo are registered trademarks of Texas Instruments and

• BrilliantColor PC/AT is a registered trademark of International Business Machines Corporation in the

• United States. Macintosh

•

and DLP® LinkTM are trademarks of Texas Instruments.

is a registered trademark of Apple Computer, Inc. in the United States and/or other countries. HDMI, the HDMI logo and High-Deﬁ nition Multimedia Interface are trademarks or

• registered trademarks of HDMI Licensing LLC. All other company or product names are trademarks or registered trademarks of their

• respective companies.

•

Some IC chips in this product include conﬁ dential and/or trade secret property belonging to Texas Instruments. Therefore you may not copy, modify, adapt, translate, distribute, reverse engineer, reverse assemble or discompile the contents thereof.

Observe the following safeguards when setting up your projector.

Caution concerning the lamp unit

Potential hazard of glass particles if lamp

■

ruptures. In case of lamp rupture, contact your nearest Sharp Authorized Projector Dealer or Service Center for replacement. See “Regarding the Lamp” on page

56.

Caution concerning the setup of the projector

For minimal servicing and to maintain high

■

image quality, SHARP recommends that this projector be installed in an area free from humidity, dust and cigarette smoke. When the projector is subjected to these environments, the vents and lens must be cleaned more often. As long as the projector is regularly cleaned, use in these environments will not reduce the overall operation life of the unit. Internal cleaning should only be per formed by a Sharp Authorized Projector Dealer or Service Center.

Rest your eyes occasionally.

Continuously watching the screen for long

■

hours will cause eye strain. Take regular breaks to rest your eyes.

Do not set up the projector in places exposed to direct sunlight or bright light.

■

Position the screen so that it is not in direct sunlight or room light. Light falling directly on the screen washes out the colors, making viewing difﬁ cult. Close the curtains and dim the lights when setting up the screen in a sunny or bright room.

Caution regarding placing of the projector

■

Place the projector on a level site within the adjustment range (9 degrees) of the adjustment foot.

After the projector is purchased, a faint

■

smell from the vent may appear when the power is ﬁ rst turned on. This is normal and is not a malfunction. It will disappear after the projector is used for a while.

When using the projector in highaltitude areas such as mountains (at altitudes of approximately 1,500 meters (4,900 feet) or more)

■

When you use the projector in high-altitude areas with thin air, set “Fan Mode” to “High”. Neglecting this can affect the longevity of the optical system.

■

Use the projector at altitudes of 2,300 meters (7,500 feet) or less.

Warning about placing the projector in a high position

■

When placing the projector in a high position, make cer tain it is carefully secure to avoid personal injury caused by the projector falling down.

Do not subject the projector to hard impact and/or vibration.

■

Protect the lens so as not to hit or damage the surface of the lens.

Avoid locations with extremes of temperature.

■

The operating temperature of the projector is from 41°F to 95°F (+5°C to +35°C).

■

The storage temperature of the projector is from –4°F to 140°F (–20°C to +60°C).

Do not block the exhaust and intake vents.

■

Allow at least 11 13/16 inches (30 cm) of space between the exhaust vent and the nearest wall or obstruction.

■

Ensure that the intake vent and the exhaust vent are not obstructed.

■

If the cooling fan becomes obstructed, a protection circuit will automatically put the projector into Standby mode to prevent overheat damage. This does not indicate a malfunction. (See pages 54 and 55.) Remove the projector power cord from the wall outlet and wait at least 10 minutes. Place the projector where the intake and exhaust vents are not blocked, plug the power cord back in and turn on the projector. This will return the projector to the normal operating condition.

Caution regarding usage of the projector

■

If you are not to use the projector for a long time or before moving the projector, make certain you unplug the power cord from the wall outlet, and disconnect any other cables connected to it.

■

Do not carry the projector by holding the lens.

■

Do not expose the projector to direct sunlight or place next to heat sources. Doing so may affect the cabinet color or cause deformation of the plastic cover.

Other connected equipment

■

When connecting a computer or other audio-visual equipment to the projector, make the connections AFTER unplugging the power cord of the projector from the AC outlet and turning off the equipment to be connected.

■

Please read the operation manuals of the projector and the equipment to be connected for instructions on how to make the connections.

Using the projector in other countries

■

The power supply voltage and the shape of the plug may vary depending on the region or country you are using the projector in. When using the projector overseas, make sure you use an appropriate power cord for the country you are in.

Temperature monitor function

If the temperature inside the projector

■

increases, due to blockage of the air vents, or the setting location, the temperature warning indicator will blink. And if the temperature keeps on rising, “ ” will illuminate in the lower left corner of the picture with the temperature warning indicator blinking. If this state continues, the lamp will turn off, the cooling fan will run and then the projector will enter Standby mode. Refer to “Maintenance Indicators” on pages 54 and 55 for details.

Info

The cooling fan regulates the internal

• temperature, and its performance is automatically controlled. The sound of the fan may change during projector operation due to changes in the

fan speed. This does not indicate malfunction.

Introduction

Closed Caption uses Bitstream Vera fonts

Permission is he reby granted, free of charge, to any person obtaining a copy of the fonts accompanying this license (“Fonts”) and associated documentation ﬁ les (the “Font Software”), to reproduce and distribute the Font Software, including without limitation the rights to use, copy, merge, publish, distribute, and/or sell copies of the Font Sof tware, and to permit persons to whom the Font Sof tware is furnished to do so, subject to the following conditions:

The above copyright and trademark notices and this pe rmission notice shall be included in all copies of one or more of the Font Software typefaces.

The Font Software may be modiﬁ ed, altere d, or added to, and in particular the designs of glyphs or characters in the Fonts may be modiﬁ ed and additional glyphs or character s may be added to the Fonts, only if the fonts are renamed to names not containing either the words “Bitstream” or the word “Vera”.

This License becomes null and void to the extent applicable to Fonts or Font Software that has been modiﬁ ed and is distribute d under the “Bitstream Vera” names.

The Font Software may be sold as part of a larger software package but no copy of one or more of the Font Software typefaces may be sold by itself.

THE FONT SOFTWARE IS PROVIDED “AS IS”, WITHOUT WARR ANT Y OF ANY KIND, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO ANY WARR ANTIES OF MERCHANTABILIT Y, FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT OF COPYRIGHT, PATENT, TRADEMARK, OR OTHER RIGHT. IN NO EVENT SHALL BITSTREAM OR THE GNOME FOUNDATION BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, INCLUDING ANY GENERAL, SPECIAL, INDIRECT, INCIDENTAL, OR CONSEQUENTIAL DAMAGES, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, OUT OF THE USE OR INABILITY TO USE THE FONT SOFTWARE OR FROM OTHER DEALINGS IN THE FONT SOFTWARE.

Except as contained in this notice, the names of Gnome, the Gnome Foundation, and Bitstream Inc., shall not be used in adver tising or other wise to promote the sale, use or other dealings in this Font Software without prior written authorization from the Gnome Foundation or Bitstream Inc., respectively. For further information, contact: fonts at gnome dot org.

Part Names and Functions

Numbers in Z refer to the main pages in this operation manual where the topic is explained.

1 2

4 5

6 7

Top V i ew

1 Temperature warning indicator 2 Lamp indicator 3 Power indicator 4 STANDBY/ON button

For turning the power on and putting the

projector into Standby mode.

5 ENTER button

For setting items selected or adjusted on

the menu.

6 VOL (Volume) buttons (–O/Q+)

For adjusting the speaker sound level.

7 AUTO SYNC button

For automatically adjusting images when

connected to a computer.

8 Adjustment buttons (P/R/O/Q)

For selecting menu items.

9 INPUT buttons (P/R)

For switching Input mode.

10 MENU button

For displaying adjustment and setting

screens.

15 16 17

Front View

11 Zoom ring

For enlarging/reducing the picture.

12 Focus ring

For adjusting the focus.

13 Intake vent 14 Security bar 15 HEIGHT ADJUST lever 16 Adjustment foot 17 Remote control sensor

1234 5

Rear View (Terminals)

Introduction

8 9

1 HDMI terminal

Terminal for HDMI input.

2 AUDIO input terminal 3 VIDEO input terminal

Terminal for connecting video equipment.

4 COMPUTER/COMPONENT input

terminal

Terminal for computer RGB and component signals.

5 RS-232C terminal

Terminal for controlling the projector using

a computer.

6 Exhaust vent 7 Speaker

8 Kensington Security Standard

connector

9 Rear adjustment foot 10 AC socket

Connect the supplied power cord.

19, 20, 21

19, 20

Using the Kensington Lock

•

This projector has a Kensington Security Standard connector for use with a Kensington MicroSaver Security System. Refer to the information that came with the system for instructions on how to use it to secure the projector.

Part Names and Functions (Continued)

Numbers in Z refer to the main pages in this operation manual where the topic is explained.

2 3

4 5

6 7

8 9

10 11

ON button

For turning the power on.

STANDBY button

For putting the projector into the Standby mode.

MAGNIFY buttons

For enlarging/reducing part of the image.

FREEZE button

For freezing images.

BREAK TIMER button

For displaying the break time.

AV MUTE button

For temporarily displaying a black screen and turning off the sound.

SPOT button

For displaying the spotlight.

13 14

15 16 17 18

19 20 21

31, 46

POINTER button

For displaying the pointer.

Adjustment buttons (P/R/O/Q)

For selecting and adjusting menu items.

EFFECT button

For changing the pointer or spot area.

KEYSTONE button

For entering the Keystone Correction mode.

FUNCTION button

For operating and executing a function assigned to “FUNCTION Button”.

VOL +/– (Volume) buttons

For adjusting the speaker sound level.

INPUT buttons (P/R) For switching Input mode.

PICTURE MODE button

For selecting the appropriate picture.

AUTO SYNC button

For automatically adjusting images when connected to a computer.

RESIZE button

For switching the picture size (NORMAL, 16:9, etc.).

MENU button

For displaying adjustment and setting screens.

ENTER button

For setting items selected or adjusted on the menu.

RETURN button

For returning to the previous menu screen during menu operations.

ECO+QUIET but ton

For lowering the noise of the cooling fan and extending the lamp life.

3D MODE button

For displaying the 3D MODE menu screen.

Inserting the Batteries

Pull down the tab on the cover and remove the

cover towards the direction of the arrow.

Insert the batteries.

Insert the batteries making sure the polarities correctly match

•

the m and n marks inside the batter y compartment.

Insert the lower tab of the cover into the opening,

and lower the cover until it clicks in place.

Incorrect use of the batteries may cause them to leak or explode. Please follow the precautions below

Caution

Danger of explosion if batter y is incorrectly replaced.

• Replace only with alkaline or manganese batteries.

Inser t the batteries making sure the polarities correctly match the m and n marks inside the batter y

• compartment. Batteries of dif ferent types have different properties, therefore do not mix batteries of dif ferent types.

• Do not mix new and old batterie s.

•

This may shorten the life of new batteries or may cause old batteries to leak.

Remove the batteries from the remote control once they have run out, as leaving them in can cause them to leak.

•

Batter y ﬂ uid from leaked batteries is harmful to skin, therefore ensure you wipe them ﬁ rst and then remove them using a cloth.

The batteries included with this projector may run down in a short period, depending on how they are kept.

• Be sure to replace them as soon as possible with new batteries. Remove the batteries from the remote control if you will not be using the remote control for a long time.

• Comply with the rules (ordinance) of each local government when disposing of worn-out batteries.

•

Introduction

Usable Range

The remote control can be used to control the projector within the ranges shown in the illustration.

Note

•

The signal from the remote control can be reﬂ ected off a screen for easy operation. However, the effective distance of the signal may differ depending on the screen material.

When using the remote control

Ensure that you do not drop it or expose it to

• moisture or high temperature. The remote control may malfunction under a

• ﬂ uorescent lamp. In this case, move the projector away from the ﬂ uorescent lamp.

Remote control

Remote control sensor

30°

Remote control signal

Remote control signal transmitters

transmitters

33n (10 m)

Easy Start

This section shows the basic operation (projector connecting with the computer). For details, see the page described below for each step.

Setup and Projection

In this section, connection of the projector and the computer is explained using one example.

STANDBY/ON

button

O/Q buttons

INPUT buttons

STANDBY button

ON button

INPUT buttons

Zoom ring

Focus ring

HEIGHT

ADJUST lever

1. Place the projector facing a wall or a screen

Adjustment

buttons (P/R/O/Q)

KEYSTONE button

P. 16

2. Connect the projector to the computer and plug the power cord into the AC socket of the projector

When connecting equipment other than a computer, see pages

20 and 21.

_PP. 19, 21

3. Turn the projector on

Press STANDBY/ON on the projector or ON on the remote control.

_P. 2 3

4. Adjust the projected image with the Setup Guide

1 After the projector turns on, the Setup Guide appears.

(When “Setup Guide” is set to “On”. See page

Follow the steps in the Setup Guide and adjust the focus, height (angle) and picture size.

45.)

3 After adjusting the focus, height (angle) and picture size, press ENTER to ﬁ nish the

Setup Guide.

_P. 24

5. Correct trapezoidal distortion

Correcting trapezoidal distortion using Keystone Correction.

On the remote control

Shrinks

upper side.

Shrinks

lower side.

_P. 2 6

6. Select the Input mode

Press INPUT P/R to display the INPUT list. Use INPUT P/R to select the Input mode.

On the

projector

On the remote

control

INPUT list

INPUT

COMPUTER

HDMI

VIDEO

Audio

Easy Start

When you select HDMI input, use O/Q to select the audio input terminal (HDMI or AUDIO).

_P. 27

7. Turn the computer on

8. Turn the power off

Press STANDBY/ON on the projector or STANDBY on the remote control, and then press the button again while the conﬁ rmation message is displayed to put the projector into Standby mode.

On the

projector

On the remote

control

On-screen display

_P. 2 3

Setting Up the Projector

Video Setup

If using this projector outside the U.S.A., please change setting to “0 IRE” in Video Setup. (See page 42.)

Setting Up the Projector

For optimal image quality, position the projector perpendicular to the screen with the projector's feet ﬂ at and level. Doing so will eliminate the need for Keystone correction and provide the best image quality. (See page 26.)

Standard Setup (Front Projection)

■

Place the projector at the required distance from the screen according to the desired picture size. (See page 17.)

Indication of the Projection Image Size and Projection Distance

Example: 16:10 Signal Input (Normal Mode)

Picture Size

300" (762 cm)

200" (508 cm)

100" (254 cm)

40" (102 cm)

34"

21"

(86 cm

85" (215 cm

54 cm)

254"×159" (646 cm × 404 cm)

170"

106"

(431 cm

53"

135 cm)

269 cm)

Projection Distance

4'4"–5'3"

(1.3 m – 1.6 m)

10'11"–13'2"

(3.3 m – 4.0 m)

21'10"–26'4"

(6.7 m – 8.0 m)

32'9"–39'6"

(10.0 m – 12.0 m)

Screen Size and Projection Distance

Screen

Note

Lens center

16:10 Signal Input (Normal Mode)

Picture (Screen) size Projection distance [L]

Diag. [χ] Width Height Minimum [L1] Maximum [L2]

300" (762 cm) 646 cm (254") 404 cm (159") 10.0 m (32' 9") 12.0 m (39' 6") 7 cm (2 250" (635 cm) 538 cm (212") 337 cm (132") 8.3 m (27' 4") 10.0 m (32' 11") 5 cm (2 200" (508 cm) 431 cm (170") 269 cm (106") 6.7 m (21' 10") 8.0 m (26' 4") 4 cm (1 23/32") 150" (381 cm) 323 cm (127") 202 cm (79") 5.0 m (16' 5") 6.0 m (19' 9") 3 cm (1 120" (305 cm) 258 cm (102") 162 cm (64") 4.0 m (13' 1") 4.8 m (15' 10") 3 cm (1 100" (254 cm) 215 cm (85") 135 cm (53") 3.3 m (10' 11") 4.0 m (13' 2") 2 cm (0 55/64")

80" (203 cm) 172 cm (68") 108 cm (42") 2.7 m (8' 9") 3.2 m (10' 6") 2 cm (0 11/16") 60" (152 cm) 129 cm (51") 81 cm (32") 2.0 m (6' 7") 2.4 m (7' 11") 1 cm (0 40" (102 cm) 86 cm (34") 54 cm (21") 1.3 m (4' 4") 1.6 m (5' 3') 1 cm (0 11/32")

4:3 Signal Input (Normal Mode)

Picture (Screen) size Projection distance [L]

Diag. [χ] Width Height Minimum [L1] Maximum [L2]

300" (762 cm) 610 cm (240") 457 cm (180") 11.3 m (37' 1") 13.6 m (44' 9") 7 cm (2 250" (635 cm) 508 cm (200") 381 cm (150") 9.4 m (30' 11") 11.4 m (37' 3") 6 cm (2 200" (508 cm) 406 cm (160") 305 cm (120") 7.5 m (24' 9") 9.1 m (29' 10") 5 cm (1 15/16") 150" (381 cm) 305 cm (120") 229 cm (90") 5.7 m (18' 7") 6.8 m (22' 4") 4 cm (1 120" (305 cm) 244 cm (96") 183 cm (72") 4.5 m (14' 10") 5.5 m (17' 11") 3 cm (1 100" (254 cm) 203 cm (80") 152 cm (60") 3.8 m (12' 4") 4.5 m (14' 11") 2 cm (0 31/32")

80" (203 cm) 163 cm (64") 122 cm (48") 3.0 m (9' 11") 3.6 m (11' 11") 2 cm (0 70" (178 cm) 142 cm (56") 107 cm (42") 2.6 m (8' 8") 3.2 m (10' 5") 2 cm (0 60" (152 cm) 122 cm (48") 91 cm (36") 2.3 m (7' 5") 2.7 m (8' 11") 1 cm (0 37/64") 40" (102 cm) 81 cm (32") 61 cm (24") 1.5 m (4' 11") 1.8 m (6' 0") 1 cm (0

Note

Allow a margin of error in the values in the

•

Allow a margin of error in the values in the

• diagrams below.

diagrams below.

Distance from the lens center

to the bottom of the image [H]

Distance from the lens center

to the bottom of the image [H]

Setup

/64")

/32") /32")

/64")

/32") /64")

/64") /64")

/32") /64")

/64")

When using the projector with screen sizes not listed in the above charts, calculate the values according to the formulas.

16:10 Signal 4:3 Signal

[m/cm] [Feet/inches] [m/cm] [Feet/inches]

L1: Minimum projection distance (m/ft) 0.03328χ0.03328χ / 0.3048 0.03768χ0.03768χ / 0.3048

L2: Maximum projection distance (m/ft) 0.04013 H:

Distance from the lens center to the bottom of the image (cm/in)

: Picture diagonal size : 40

-300

0.02178χ0.02178χ / 2.54 0.02466χ0.02466χ / 2.54

0.04013χ / 0.3048 0.04543χ0.04543χ / 0.3048

Setting Up the Projector (Continued)

Projection (PRJ) Mode

The projector can use any of the 4 projection modes shown in the diagram below. Select the mode most appropriate for the projection setting in use. (You can set the PRJ mode in “SCRADJ” menu. See page 45.)

Table mounted, front projection

■

[Menu item ➞ “Front”]

■

Table mounted, rear projection (with a translucent screen) [Menu item ➞ “Rear”]

Ceiling mounted, front projection

■

[Menu item ➞ “Ceiling + Front”]

■

Ceiling mounted, rear projection (with a translucent screen) [Menu item ➞ “Ceiling + Rear”]

a

Ceiling-Mount Setup

It is recommended that you use the optional Sharp ceiling-mount adaptor and unit for this installation. Before mounting the projector, contact your nearest Sharp Authorized Projector Dealer or Service Center to obtain the recommended ceiling-mount adaptor and unit (sold separately).

Connecting the Projector to Other Equipment

Before connecting, ensure that the power cord of the projector is unplugged from the AC outlet and turn off the equipment to be connected. After making all connections, turn on the projector and then the other pieces of equipment. When connecting a computer, ensure that it is the last equipment to be turned on after all the connections are made.

IMPORTANT:

Ensure that the appropriate input mode has been selected on the projector before you turn on the connected equipment.

For more details of connection and cables, refer to the operation manual of the connecting equipment.

• You may need other cables or connectors not listed below.

•

Terminals on the Projector

Equipment

Computer

Terminal on

connected equipment

RGB

output

terminal

Cable

RGB cable (supp lied) COMPUTER/

Terminal o n the

projector

COMPONENT

Connections

HDMI output

terminal

Note

•

Depending on speciﬁ cations of equipment or the DVIÙHDMI digital cable, the signal transmission may not work property. (The HDMI speciﬁ cation does not suppor t all connections to equipment that has digital output terminal using a DVIÙHDMI digital cable.)

•

See page with computer signals other than those listed may cause some of the functions to not work.

•

A Macintosh adaptor may be required for use with some Macintosh computers. Contact your nearest Macintosh Dealer.

Depending on the computer you are using, an image may not be projected unless the

• computer's external output port is switched on (e.g. Press “Fn” and “F5” keys simultaneously when using a SHARP notebook computer). Refer to the speciﬁ c instructions in

your computer's operation manual to enable your computer's external output port.

64 “Compatibility Chart” for a list of computer signals compatible with the projector. Use

HDMI cable (commercially available) HDMI

Connecting the Projector to Other Equipment (Continued)

Equipment

Video equipment

Camera/Video game

Terminal on

connected equipment

HDMI output

terminal

Component

video output

terminal

Video output

terminal

Component

video

output

terminal

Video

output

terminal

Cable

HDMI cable (commercially available) HDMI

3 RCA to mini D-sub 15 pin cable (optional, AN-C3CP2)

Video cable (commercially available) VIDEO

Cables for a camera or a vi deo game/3 RCA to mini D-sub 15 pin cable (optional, AN-C3CP2)

RCA adaptor plug (commercially available)

Cables for a camera or a vi deo game

Terminal o n the

projector

COMPUTER/ COMPONENT

VIDEO

Note

Depending on speciﬁ cations of equipment or the DVIÙHDMI digital cable, the signal transmission

• may not work property. (The HDMI speciﬁ cation does not suppor t all connections to equipment that has digital output terminal using a DVIÙHDMI digital cable.) HDMI (High-Deﬁ nition Multimedia Interface) is a digital AV interface that can deliver a high-deﬁ nition

• video signal, multi-channel audio signal, and bi-directional control signal all in just one cable. Because it is compatible with the HDCP (High-bandwidth Digital Content Protection) system, the

• digital video signal does not degrade when transmitted, and a high-quality image with a simple connection can be enjoyed. The HDMI terminal does not support the CEC signal.

• When you connect video equipment with a 21-pin RGB output (Euro-scar t) to the projector, use a

• commercially available cable that ﬁ ts in the projector terminal you want to connect. The projector does not suppor t RGBC signals via the Euro-scart.

•

Equipment

Audio equipment

Terminal on

connected equipment

ø3.5 mm

audio output

terminal

Cable

ø3.5 mm stereo minijack to RCA audio cable (commercially available)

Terminal o n the

projector

AUDIO

RCA audio

output

terminal

Audio

output

terminal

HDMI output

terminal

Note

You can select HDMI or AUDIO in the INPUT list. (See page 27.)•

RCA audio cable (commercially available)

Cables for a camera or a vi deo game

HDMI cable (commercially available) HDMI

This projector is able to process the following signals when connected to HDMI equipment:

•

Video signal: For details, see “Digital Support” in the list of “Compatibility Char t” on page 64.

•

Audio signal: Linear PCM audio

•

Sampling frequency: 48kHz/44.1kHz/32kHz

Connecting the Power Cord

Connections

Plug the supplied power cord into the AC socket on the rear of the projector. Then plug into AC outlet.

Power cord

Power cord (supplied)

(supplied)

AC socket

To A C out l et

Controlling the Projector by a Computer

When the RS-232C terminal on the projector is connected to a computer with an RS-232C serial control cable (cross type, commercially available), the computer can be used to control the projector and check the status of the projector. See page 59 for details.

When connecting to a computer using an RS-232C serial control cable

To R S -23 2C terminal

RS-232C serial control cable

(cross type, commercially available)

To R S -23 2C terminal

Computer

Note

The RS-232C function may not operate if your computer terminal is not correctly set up. Refer to the

• operation manual of the computer for details.

Info

•

Do not connect the RS-232C cable to a por t other than the RS-232C terminal on the computer. This may damage your computer or projector. Do not connect or disconnect an RS-232C serial control cable to or from the computer while it is on.

• This may damage your computer.

RS-232C Terminal: D-sub 9 pin male connector

Pin No. Signal Name I/O Reference

RD SD

RS CS

Receive Data Send Data

Signal Ground

Reque st to Send Clear to S end

Input Output

Not connected Conne cted to inter nal circ uit Conne cted to inter nal circ uit Not connected Conne cted to inter nal circ uit Not connected Conne cted to CS in in ternal c ircuit Conne cted to RS in in ternal circuit Not connected

RS-232C Cable recommended connection: D-sub 9 pin female connector

Pin No. Signal Pin No. Signal

Note

Depending on the controlling device used, it may be necessary to

• connect Pin 4 and Pin 6 on the controlling device (e.g. computer).

Projector

Pin No.

4 5 6

Computer

Pin No.

4 5 6

Turning the Projector On/Off

Info

Turning the Projector On

Note that the connections to external equipment and power outlet should be done before performing the operations written below. (See pages

Press STANDBY/ON on the projector or ON on the remote control.

The power indicator illuminates green.

• After the lamp indicator illuminates, the projector

• is ready to start operation.

Note

About the Lamp Indicator

•

The lamp indicator illuminates to indicate the status of the lamp.

Green: The lamp is on. Blinking in green: The lamp is warming up. Red: The lamp is shut down

abnormally or the lamp should be replaced.

When switching on the projector, a slight

• ﬂ ickering of the image may be experienced within the ﬁ rst minute af ter the lamp has been illuminated. This is normal operation as the lamp's control circuitry is stabilising the lamp output characteristics. It should not be regarded as faulty operation. If the projector is put into Standby mode and

• immediately turned on again, the lamp may take some time to start projection. When System Lock is set, the keycode input

• box appears. To cancel the keycode setting, input the keycode that you have already set. See page

47 for details.

19 to 21.)

•

When “Auto Restart” is set to “On”:

If the power cord is unplugged from the outlet or the breaker switch is turned of f when the projector is on, then the projector automatically turns on when the power cord is plugged into the AC outlet or the breaker switch is turned on. (See page

•

English is the factor y default language. If you want to change the on-screen display to another language, change the language according to the procedure on page

46.)

45.

Power indicator Lamp indicator

STANDBY/ON button

STANDBY button

ON button

Operation

Basic

Turning the Power Off (Putting the Projector into Standby Mode)

Press STANDBY/ON on the projector or STANDBY on the remote control, then press that button again while the conﬁ rmation message is displayed, to put the projector into Standby mode.

The projector cannot be turned on while cooling.

•

On-screen display (conﬁ rmation message)

Info

Direct Power Off function:

•

You can unplug the power cord from the AC outlet even if the cooling fan is still running.

Image Projection

About the Setup Guide

After turning on the projector, the Setup Guide screen appears to assist you with projector setup.

Guidance items 1 FOCUS 2 HEIGHT ADJUST 3 ZOOM

Press ENTER to exit the Setup Guide screen.

Note

•

The Setup Guide screen automatically highlights the items in the following order:

1 FOCUS

However, you can adjust the focus, height (angle) or zoom regardless of the highlighted item. If you do not want to display the Setup Guide

• for the next time, set “Menu” - “SCR-ADJ” “Setup Guide” to “Off ”. (See page

2 HEIGHT ADJUST

3 ZOOM4 ENTER

45.)

ENTER button

Focus ring

Adjusting the Projected Image

1 Adjusting the Focus

You can adjust the focus with the focus ring on the projector.

Rotate the focus ring to adjust the focus while watching the projected image.

Using the knob on the focus ring will make the

• adjustments easier.

2 Adjusting the Height

The height of the projector can be adjusted using the adjustment feet at the front and rear of the projector.

When the screen is above the projector, the projection image can be made higher by adjusting the projector.

Lift the projector to adjust its

height while lifting the HEIGHT ADJUST lever.

Remove your hands from the

HEIGHT ADJUST lever of the projector after its height has been ﬁ nely adjusted.

The angle of projection is adjustable up to

• 9 degrees from the surface on which the projector is placed.

Use the rear adjustment foot to

make the projector level.

•

The projector is adjustable ±2 degrees from the standard position.

Note

When adjusting the height of the projector,

• trapezoidal distor tion occurs. Follow the procedures in Keystone Correction to correct the distor tion. (See pages

26 and 43.)

Make small adjustments.

HEIGHT ADJUST lever

Rear adjustment footRear adjustment foot

Info

Do not apply too much pressure on the

• projector when the front adjustment foot comes out. When lowering the projector, be careful not to

• get your ﬁ ngers caught in the area between the adjustment foot and the projector. Hold the projector ﬁ rmly while lifting or carrying.

• Do not hold by the lens area.

•

Operation

Basic

3 Adjusting the Picture Size

You can adjust the picture size using the zoom ring on the projector.

Rotate the zoom ring to enlarge or shrink the picture size.

Using the knob on the zoom ring will make the

• adjustments easier.

Zoom ringZoom ring

Image Projection (Continued)

Correcting Trapezoidal Distortion

When the image is projected either from the top or from the bottom towards the screen at an angle, the image becomes distorted trapezoidally. The function for correcting trapezoidal distortion is called Keystone Correction.

Adjustment buttons (P/R/O/Q)

Note

The Keystone Correction can be adjusted up to

• an angle of approximately ±40 degrees and the screen can also be set up to an angle of approximately ±40 degrees (When the Resize mode is set to “NORMAL” (see page

Press KEYSTONE to enter the

Keystone Correction mode.

Press P/Q or O/R to adjust the

Keystone Correction.

Note

•

To return to the default setting, press RETURN while the on-screen display of the Keystone Correction mode is on the screen.

Press KEYSTONE.

The on-screen display of the Keystone

• Correction mode will disappear.

28))

RETURN button

KEYSTONE button

On-screen display (Keystone Correction mode)

ADJUST END

Shrinks upper side. (Move the slide bar in the + direction.)

Shrinks lower side. (Move the slide bar in the - direction.)

0KEYSTONE

Info

•

While adjusting the image using Keystone Correction, straight lines and the edges of the image may appear jagged.

Switching the Input Mode

Select the appropriate Input mode for the connected equipment.

Press INPUT P/R to display the INPUT list. Use INPUT P/R to select the Input mode.

When you select HDMI input, use O/Q to select the audio input terminal (HDMI or AUDIO).

Adjusting the Volume

Press VOL +/– on the remote control or –O/Q+ on the projector to adjust the volume.

Note

Pressing VOL–/–O will lower the volume.

•

Pressing VOL+/Q+ will raise the volume.

•

On-screen displayOn-screen display

VOL +/– (Volume)

VOL +/– (Volume) buttons

buttons

INPUT buttons

AV MUTE bu tton

O/Q buttons

Operation

Basic

Displaying the Black Screen and Turning Off the Sound

Temporarily

Press AV MUTE on the remote control to temporarily display a black screen and turn off the sound.

Note

Pressing AV MUTE again will turn the

• projected image back on.

On-screen displayOn-screen display

Image Projection (Continued)

Resize Mode

This function allows you to modify or customize the Resize mode to enhance the input image. Depending on the input signal, you can choose a desired image.

Press RESIZE.

See page 43 for set ting on menu screen.

•

COMPUTER

SVGA (800 × 6 00)

4:3 aspect ratio

Other aspect ratios

Computer Image type NORMAL FULL NATIVE 16:9

XGA (1024 × 768) 1024 × 768

SXGA (1152 × 864) 1152 × 864

SXGA+ (1400 × 1050) 1400 × 1050

SXGA (1280 × 1024) 1000 × 800 1280 × 1024

1280 × 720 1280 × 720 —

1366 × 768 1280 × 720 1366 × 768

1280 × 768 1280 × 768

1280 × 800 1280 × 800 —

Input signal Outp ut scr een image

NORMAL FULL NATIVE 16:9

800 × 60 0

1068 × 800

1280 × 800

— 1280 × 720

RESIZE

RESIZE button

button

1280 × 720

—1360 × 768 1280 × 722 1360 × 768

Resolution XGA and below

Resolution higher than

XGA

SXGA (1280 × 1024)

1280 × 72 0

1360 × 76 8 1366 × 76 8

1280 × 76 8

1280 × 800

: Cutout a rea on whi ch images canno t be proje cted

: Area wh ere the si gnals are off scr een *1 The Imag e Shif t functi on can be u sed for th ese images. *2 Same as NORMAL m ode. *3 In case SXG A+ input.

4:3 as pect ra tio

5:4 asp ect r atio

16:9 aspect ratio

15:9 aspect ratio

16:10 aspe ct ratio

—

VIDEO/DTV

Input signal Outp ut scr een image

Video/DTV Image type NORMAL AREA ZOOM V-STRETCH 16:9

4:3 as pect ra tio

480

I, 480P,

576

I, 576P,

NTSC, PAL,

SECAM

Squeeze

Letter box

720P, 1035

1080

I, 1080P

16:9 aspect ratio

540P

: Cutout a rea on whi ch images canno t be proje cted

: Area on w hich the i mage is no t includ ed in the origina l signa ls *1 The Imag e Shif t functi on can be u sed for th ese images. *2 Same as NORMAL m ode.

16:9 aspect ratio

(4:3 aspect ra tio in 16:9)

—

Operation

Basic

About Copyrights

When using the Resize function to select an image size with a different aspect ratio to a TV

• program or video image, the image will look different from its original appearance. Keep this in mind while choosing an image size. The use of the Resize or Keystone Correction function to compress or stretch the image for

• commercial purposes/public displays in a café, hotel, etc. may be an infringement of copyright protected by law for copyright holders. Please use caution.

Operating with the Remote Control

MAGNIFY buttons

FREEZE button

PICTURE MODE button

AUTO SYNC button

BREAK TIMER button

SPOT button

Adjustment buttons (P/R/O/Q)

EFFECT button

ECO+QUIET button

POINTER button

Displaying and Setting the Break Timer

Press BREAK TIMER.

The timer starts to count down from 5

• minutes.

On-screen display

Press P/R/O/Q to adjust the

length of the break time.

Increases with P or Q

•

5 minutes ➞ 6 minutes ➞ 60 minutes

Shortens with O or R

•

4 minutes ➞ 3 minutes ➞1 minute The break time can be set in units of one

• minute (up to 60 minutes).

Canceling the break timer display function

Press BREAK TIMER.

Note

•

The Break Timer is not available while the projector is operating the following functions.

- Auto Sync

- Freeze

- AV Mute

- Input Search

Displaying the Pointer

Press POINTER and press P/R/

O/Q on the remote control to move the pointer.

Press EFFECT to change the pointer icon

• (5 types).

Finger1 Finger2 Heart Underline

Star

Press POINTER again.

•

The pointer will disappear.

Using the Spot Function

Press SPOT and press P/R/O/Q

on the remote control to move the spot area.

•

Press EFFECT to change the spot area size (3 types).

1/9 1/25 1/8

Press SPOT again.

•

The spot area will disappear.

Switching the Eco+Quiet Mode

Press ECO+QUIET to switch the Eco+Quiet mode between on and off.

•

When the Eco+Quiet Mode is set to “ON”, the sound of the cooling fan will turn down, the power consumption will decrease, and the lamp life will extend.

Note

Refer to “Eco+Quiet” on page 40 for details.•

Auto Sync

(Auto Sync Adjustment)

Displaying an Enlarged Portion of an Image

Auto Sync function works when detecting input signal after the projector turns on.

Press AUTO SYNC to manually adjust with Auto Sync function.

Note

•

When the optimum image cannot be achieved with Auto Sync adjustment, use manual adjustments. (See page

41.)

Freezing a Moving Image

Press FREEZE.

The projected image is frozen.

•

Press FREEZE again to return to

the moving image from the currently connected device.

Selecting the Picture Mode

You can select the appropriate Picture mode for the projected image, such as movie or video game.

Press PICTURE MODE.

When pressing PICTURE MODE, the Picture

• mode changes in the following order:

STANDARD PRESENTATION MOVIE GAME sRGB

Graphs, tables and other portions of projected images can be enlarged. This is helpful when providing more detailed explanations.

Press MAGNIFY on the

remote control.

Enlarges the image.

• Pressing

• or reduces the projected image.

Note

Press

×1 ×2 ×3 ×4

Press

You can change the location of the

•

enlarged image using P, R, O and Q.

Press RETURN on the remote

control to cancel the operation.

The magniﬁ cation then returns to ×1.

•

Note

•

The selectable magniﬁ cations differ depending on the input signal.

•

In the following cases, the image will return to the normal size (×1).

- When switching the Input mode.

- When RETURN has been pressed.

- When the input signal is changed.

- When the input signal resolution and refresh rate (vertical frequency) change.

- When the Resize mode is changed.

or MAGNIFY enlarges

Features

Useful

Note

See page 38 for details on the Picture mode.•

* “sRGB” is displayed only when RGB signal is input.

Menu Items

The following shows the items that can be set in the projector.

“Quick Start Menu”

Main menu

Quick Start Menu

Input Search Start

Page 36

Resolution

Page 36

Resize

Page 36

Keystone

-80 +80

Page 36

Eco + Quiet

[On/Off]

Page 36

Language

Page 36

Information

Page 36

Go To Complete Menu

Page 36

Sub menu

Normal Full Native Area Zoom V-Stretch Border 16:9

English Deutsch Español Nederlands Français Italiano Svenska Português

polski Magyar Türkçe

Tiếng Việt

“Picture” menu

Main menu Sub menu

Picture

Picture Mode

Page 38 Page 38

Contrast

Bright

Color

Tint

Sharp

Red

Blue

Standard Presentation Movie Game sRGB

+30-30

Page 39

CLR Temp

1-1

Page 39

BrilliantColor™

Page 39

C.M.S. Setting [On/Off]

Page 39

C.M.S.

Page 39

Film Mode

Page 40

DNR Level 1

Page 40

[On/Off]

Eco+Quiet

Auto Off

Level 2 Level 3

Page 40

Reset

C.M.S.-Hue

Page 39

C.M.S.-Saturation

Page 39

C.M.S.-Value

Page 39

Reset

Return

Reset

+30-30

“Signal adjustment (SIG-ADJ)” menu

Main menu Sub menu

SIG-ADJ

Page 41

Clock

Phase

H-Pos

V-Pos

Reset

+150-150

+30-30

+150-150

+60-60

Page 41

Resolution

Page 41

Signal Type

Page 41

Dynamic Range Auto

Page 41

Video System Auto

Page 42

Video Setup

Page 42

Signal Info

Auto RGB YPbPr

Standard Enhanced

PAL SECAM NTSC4.43 NTSC3.58 PAL -M PAL -N PAL-60

0 IRE

7.5 IRE

Page 42

“Screen adjustment (SCR-ADJ)” menu

Main menu Sub menu

SCR - ADJ

Page 43

Resize

Page 43

Image Shift

-40 +40

Page 43

Keystone

-80 +80

Normal Full Native Area Zoom V-Stretch Border 16:9

Page 43

Overscan [On/Off]

Page 44

OSD Display [On/Off]

Page 44

Closed Caption

Page 44

Background

Page 45

Setup Guide [On/Off]

Off CC1 CC2

Logo Blue None

Page 45

PRJ Mode

Page 45

Wall Color Off

Page 45

Language

Page 45

Front Ceiling + Front Rear Ceiling + Rear

Blackboard Whiteboard

English Deutsch Español Nederlands Français Italiano Svenska Português

polski Magyar Türkçe

Tiếng Việt

Features

Useful

Menu Items

(Continued)

“Projector adjustment (PRJ-ADJ1/2)” menu

Main menu Sub menu

PRJ-ADJ1

Page 46

Auto Sync [On/Off]

Page 46

Auto Power Off [On/Off]

Page 46

Auto Restart [On/Off]

Page 46

Speaker [On/Off]

Page 46

Fan Mode

Page 46

System Lock [Enable/Disable]

Normal High

Page 47

Keylock [On/Off]

Page 48

Main menu Sub menu

PRJ-ADJ2

Page 46

Quick Start Menu [On/Off]

Page 49

FUNCTION Button

Page 49

STANDBY Mode

Page 49

DLP® LinkTM [On/Off]

Page 49

LinkTM Invert

DLP

Input Search Audio Mute Image Shift Signal Info

Quick Start Eco

Page 49

All Reset

Page 49

Lamp Timer (Life)

Page 49

Using the Menu Screen

Select from the Quick Start Menu, which is a collection of the most frequently used functions, or the Complete Menu, which enables advanced settings and adjustments.

Adjustment buttons (P/R/O/Q)

ENTER button

MENU button

ENTER button

Adjustment buttons (P/R/O/Q)

RETURN button

Press RETURN to return

• to the previous screen when the menu is displayed.

Menu Selections (Quick Start Menu)

This operation can also be performed by using the buttons on the projector.•

Press MENU.

The “Quick Start Menu” screen for the

• selected Input mode is displayed.

Press P or R to select the

desired item, then press ENTER.

Press P/R/O/Q to adjust the

item selected, then press ENTER.

Info

To display the advanced settings and

• adjustments, select “Go To Complete Menu”. Press ENTER to display the Complete Menu screen.

•

If you do not want to display the Quick Start Menu, set “Go To Complete Menu” - “PRJ-ADJ2”

- “Quick Start Menu” to “Off ”. (See page

49.)

Input Search Start Resolution Resize

Keystone Eco+Quiet Language Information

SEL./ADJ. ENTER END

Example

Quick Start Menu

1024×768 Normal

Off English

Go To Complete Menu…

Features

Useful

Using the Menu Screen

(Continued)

Quick Start Menu

The following items can be conﬁ gured on the Quick Start Menu.

Selectable items Description

Input Search Start Automatically searches for and switches to the appropriate Input mode.

Resolution Manually change the resolution.

Resize Changes the Resize mode.

Keystone Corrects the keystone distor tion of projected images.

Eco+Quiet When set to “On”, this function reduces the cooling fan noise and power

Language Selects the language displayed on the screen. (See page 45.)

Information Displays the input signal, lamp use time, remaining lamp life, etc.

Go To Complete Menu Displays the Complete Menu for advanced settings and adjustments.

Note

•

The setting of Resize mode will be made independently for each Input mode.

•

The setting of Eco+Quiet mode will be made independently for each Input mode and each Picture mode.

Pressing an operation button during input searching cancels the search.

Use this function when the image and screen size do not match with the resolution selected automatically. (See page

Use this function to stretch the image vertically or horizontally or when the edges of the image cannot be seen. (See page

Use this function to correct the trapezoidal distortion of images caused when projecting images at an angle to the screen. (See page

consumption, thereby prolonging the operating life of the lamp. (See page

41.)

43.)

40.)

Menu Selections (Complete Menu)

Example: Adjusting “Bright”.

This operation can also be performed by using the buttons on the projector.•

Press MENU.

The “Quick Start Menu” screen is

• displayed.

Press P or R to select “Go To

Complete Menu”.

Press Q or O and select

“Picture” to adjust.

Info

•

When “PRJ-ADJ2” - “Quick Start Menu” is set to “On”, pressing MENU displays the Quick Start Menu screen.

Example: “Picture” screen menu for COMPUTER (RGB) input

Menu item

SIG SCR PRJ1 PRJ2Picture

Picture Mode

Contrast 0 Bright Red Blue CLR Temp BrilliantColor C.M.S. Setting C.M.S. DNR Eco+Quiet Reset

SEL./ADJ. ENTER END

Standard

0 0

0 0 0 1

Level 2

Off

Press P or R and select “Bright”

to adjust.

•

The selected item is highlighted.

To adjust the projected image while watching it

Press ENTER.

•

The selected item (e.g. “Bright”) is displayed by itself at the bottom of the screen. When pressing P or R, the following item

• (“Red” af ter “Bright”) will be displayed.

Note

Press ENTER again to return to the

• previous screen.

Picture

Picture Mode

Items to be adjusted

Pict. SCR-ADJ

Resize

Resize Image Shift 0

Image Shift 0 Keystone

Keystone

The item displayed by itself

SIG SCR PRJ1 PRJ2Picture

Contrast 0

Bright 0

Red

Red Blue

Blue CLR Temp

CLR Temp BrilliantColor

BrilliantColor C.M.S. Setting

C.M.S. Setting C.M.S.

C.M.S.

DNR

DNR Eco+Quiet

Eco+Quiet Reset

Reset

SEL./ADJ. END

SEL./ADJ. Single ADJ END

Picture

SEL./ADJ. Rtn. Menu END

SIG

0 0

0 1

PRJ1 PRJ2

0Bright

Standard

Level 2

Level 2 Off

Off

Normal

Press ENTER.

Picture SIG SCR PRJ1 PRJ2

Press O or Q to adjust the item

selected.

•

The adjustment is stored.

Press MENU.

The menu screen will disappear.

•

Picture SIG SCR PRJ1 PRJ2

Picture Mode

Contrast 0

Red

Red Blue

Blue CLR Temp

CLR Temp BrilliantColor

BrilliantColor C.M.S. Setting

C.M.S. Setting C.M.S.

C.M.S.

DNR

DNR Eco+Quiet

Eco+Quiet Reset

Reset

SEL./ADJ. Single ADJ END

Note

The MENU button is not available while the projector is operating:

•

- Auto Sync/Break Timer/Freeze/AV Mute/Input Search

Standard

15Bright

0 0

0 1

Level 2

Level 2 Off

Off

Features

Useful

Picture Adjustment (“Picture” Menu)

Menu operation n Page 36

Q PAGE1 Q PAGE2

Picture SIG SCR PRJ1 PRJ2

Picture Mode

Contrast 0 Bright Color Tint

Red Blue

Standard

0 0 0 0Sharp 0 0

Picture SIG SCR PRJ1 PRJ2

Picture Mode

CLR Temp

3 2

4 5

6 7

BrilliantColor C.M.S. Setting C.M.S. Film Mode DNR Eco+Quiet Reset

Standard

0 1

Auto Level 2 Off

SEL./ADJ. ENTER END

Selecting the Picture Mode

Selectable

items

Description

The default settings of each item when selecting Picture Mode

CLR Temp BrilliantColor

SEL./ADJ. ENTER END

Eco+Quiet

Standard For standard image 0 1 Off

Presentation Brightens portions of image for

02Off

Adjusting the Image

Adjustment

items

Contrast For less

Bright For less

Color*

Tint*

Sharp*

Red*

Blue*

BrilliantColor™*2 *3For making the

*1 Not displayed in the RGB input mode. *2 Not adjustable/selectable when selecting “sRGB”. *3 BrilliantColor™ uses Texas Instruments'

BrilliantColor™ technology. As the BrilliantColor™ level is increased, the image becomes brighter while the color reproduction is kept at a high level.

O button Q button

contrast.

brightness. For less color

intensity. For making skin

tones purplish. For less

sharpness. For weaker red. For stronger

For weaker blue.

effect weaker.

For more contrast.

For more brightness.

For more color intensity.

For making skin tones greenish.

For more sharpness.

red. For stronger

blue. For making the

effect stronger.

Note

To reset all adjustment items, select “Reset”

•

and press ENTER.

Adjusting the Color

Temperature

Selectable

items

For lower color temperature for warmer, reddish incandescent-like

–1

images.

For higher color temperature for cooler, bluish, ﬂ uorescent-like images.

Note

Values on “CLR Temp” are only for general

• standard purposes.

Description

Adjusting the Colors

This function adjusts each of the six main colors that comprise the color wheel, altering their “Hue”, “Saturation”, or “Value”.

Selectable items Description

C.M.S.-Hue Sets the hue of the main colors.

C.M.S.-Saturation Sets the saturation of the main

C.M.S.-Value Sets the brightness of the main

Reset The adjustments of “Hue”,

Return Returns to the “Picture” menu

colors

colors.

“Saturation” and “Value” of all colors are reset to the default setting.

screen.

Adjusting “Hue”, “Saturation”, or “Value”.

1 Select “On” for “C.M.S. Setting” in the “Picture”

menu and then press ENTER.

2 Select “C.M.S.” in the “Picture” menu and then

press ENTER.

3 Press P or R to select either “Hue”, “Saturation”, or

“Value” and then press ENTER.

4 Select the color to be adjusted with P or R and

adjust it with O or Q.

Example of adjusting the “Hue”

Main colors O button Q button

R (Red)

Y (Yellow) Closer to red Closer to green

G (Green) Closer to yellow Closer to cyan

C (Cyan) Closer to green Closer to blue

B (Blue) Closer to cyan

M (Magenta) Closer to blue Closer to red

When “Saturation” is selected, the selected

•

Closer to magenta

color becomes O: lighter. Q: thicker. When “Value” is selected, the selected color

• becomes O: darker. Q: brighter. To reset the adjustment values of each color to

• the default settings, select “Reset” and press ENTER.

Closer to yellow

Closer to magenta

Features

Useful

Picture Adjustment (“Picture” Menu) (Continued)

Menu operation n Page 36

Selecting the Film Mode

This function provides high-quality playback of images originally projected at 24 fps, such as movies on DVDs.

Selectable

items

Auto Films are detected automatically.

Off Films are not detected.

Note

•

This function is available for the following signals. With COMPUTER/COMPONENT input:

- 480I

- 576I

- 1035I

- 1080I

With VIDEO input:

- All signals

Reducing Image Noise (DNR)

Video digital noise reduction (DNR) provides high quality images with minimal dot crawl and cross color noise.

Selectable

items

Level 1

Level 2

Level 3

Sets the DNR level for viewing a clearer picture.

Description

Eco+Quiet

Selectable

items

On Approx. 75%

Off 100%

Note

•

When “Eco+Quiet” is set to “On”, the fan sound and power consumption are lower than they are when “Off” is selected. (Projection brightness decreases as shown in the chart.)

Brightness and Power consumption

Note

This function is not available for some signals.•

Signal Adjustment (“SIG-ADJ” Menu)

Menu operation n Page 36

Pict. SIG-ADJ SCR PRJ1 PRJ2

Clock

Phase

H-Pos V-Pos

Reset

Resolution

Signal Type

Dynamic Range

Video System

Video Setup

6 7

Adjusting the Computer Image

Signal Info 1024 x 768

H 48.3 kHz / V 60.0 Hz

SEL./ADJ. ENTER END

If the optimum image cannot be obtained with Auto Sync adjustment, use the SIG-ADJ function.

Selectable

items

Clock Adjusts vertical noise.

Phase Adjusts horizontal noise (similar to

tracking on your VCR).

H-Pos Centers the on-screen image by

moving it to the left or right.

V-Pos Centers the on-screen image by

moving it up or down.

Description

0 0 0 0

1024 x 768 Auto Standard Auto 0 IRE

Signal Type Setting

This function allows you to select the input signal type RGB or Component for COMPUTER/COMPONENT.

Selectable

items

Auto Input signals are automatically

RGB Set when RGB signals are received.

YPbPr Set when Component signals are

recognized as RGB or component.

received.

Description

Note

•

To reset all adjustment items, select “Reset” and press ENTER. The adjustable range of “H-Pos” (H-Position)

• and “V-Pos” ( V-Position) may vary depending on the screen resolution of the computer.

Resolution Setting

Ordinarily, the type of input signal is detected and the correct Resolution mode is automatically selected. However, for some signals, the optimal Resolution mode in “Resolution” may need to be selected to match the computer display mode.

Note

•

See “Checking the Input Signal” on page 42 for information on the currently selected input signal.

Selecting the Dynamic Range

An optimum picture may not be displayed if an HDMI-capable device’s output signal type and the projector’s input signal type do not match. If this should occur, switch “Dynamic Range”.

Selectable

items

Auto In most circumstances, “Auto” should

Standard When the black levels of the image

Enhanced

be selected.

show banding or appear faded, select the item that results in the best picture quality.

Description

Note

The Dynamic Range can be selected only

• when “HDMI” input mode is selected.

Features

Useful

Signal Adjustment (“SIG-ADJ” Menu) (Continued)

Menu operation n Page 36

Setting the Video System

The video input system mode is factory preset to “Auto”; however, a clear picture from the connected audio-visual equipment may not be received, depending on the Video signal difference. In that case, switch the Video signal.

Selectable items

Auto

PAL

SECAM

*NTSC4.43

NTSC3.58

PAL-M

PAL-N

PAL-60

* When reproducing NTSC signals in PAL

video equipment.

Note

•

The Video signal can only be set in VIDEO mode.

•

When “Video System” is set to “Auto”, you may not receive a clear picture due to signal differences. Should this occur, switch to the video system of the source signal.

Setting the Video Setup

Selectable

items

0 IRE Sets the black level to 0 IRE.

7.5 IRE Sets the black level to 7.5 IRE.

Note

•

This function is available for the following signals. With COMPUTER/COMPONENT input:

- 480I

With VIDEO input:

- NTSC3.58

Checking the Input Signal

This function allows you to check the current input signal information.

Description

Adjusting the Projected Image (“SCR-ADJ” Menu)

Menu operation n Page 36

Pict. PRJ1 PRJ2SIG

Resize

Image Shift 0

Keystone

3 4

Overscan

OSD Display

Closed Caption

Background Setup Guide

PRJ Mode

Wall Color

Language

SEL./ADJ. ENTER END

Setting the Resize Mode

Use this function to stretch the image vertically or horizontally or when the edges of the image cannot be seen.

Note

For details of the Resize mode, see pages

•

28 and 29.

You can also press RESIZE on the remote

• control to set the Resize mode. (See page

28.)

SCR-ADJ

Normal

On On Off Logo On Front

Off English

Keystone Correction

Select “Keystone” on the “SCR-ADJ” menu and adjust with the slide bar.

See page 26 for details of Keystone Correction.

O buttonQ button

Adjusting the Image

Position

You can move the projected image vertically.

Q buttonO button

Note

This function only works in some Resize

• modes. (See pages

28 and 29.)

Note

The Keystone Correction can be adjusted up to

• an angle of approximately ±40 degrees (When the Resize mode is set to “NORMAL”). You can also press KEYSTONE on the

• remote control to adjust Keystone Correction.

Features

Useful

Adjusting the Projected Image (“SCR-ADJ” Menu) (Continued)

Menu operation n Page 36

Setting the Overscan

This function allows you to set the overscan area (display area).

Selectable

items

On The input area is displayed without the

Off The whole input area is displayed.

This function is available for the following

• signals. With COMPUTER/COMPONENT or HDMI* input:

- 480P

- 540P

- 576P

- 720P

- 1035I

- 1080I/1080P If noise appears at the screen edges when

• “Off” is selected, set the function to “On”. Also see “About Copyrights” on page

•

screen edges.

Note

Setting the On-screen

Description

29.

Display

Selectable

items

On All on-screen displays are displayed.

Off VOLUME/AV MUTE/FREEZE/AUTO

SYNC/RESIZE/PICTURE MODE/ ECO+QUIET/MAGNIFY/Input Search/ Audio Mute/“An invalid button has been pressed.” are not displayed.

Description

Closed Caption

Info

This function is available for NTSC3.58 signal.

• This function does not work when the Resize

• mode is set to “Border”.

•

This function is available in the following cases only:

Resize mode Keystone Correction

Normal Area Zoom V-Stretc h

16:9 -12 − +12

“Closed Caption” is a system which allows

• conversations, narration, and sound effects in T V programs (Limited regions) and home videos to be viewed as captions on the screen. Not all programs and videos will offer closed

• captioning. Please look for the symbol to ensure that captions will be shown. Two channels are available: CC1 and CC2.

•

Selectable

items

Off —

CC1 Closed Caption mode for CH1 data

CC2 Closed Caption mode for CH2 data

Note

Closed Caption may malfunction (white blocks,

• strange characters, etc.) if signal conditions are poor or if there are problems at the broadcast source. This does not necessarily indicate a problem with the projector. If any button is pressed to call up the on-

• screen display while viewing a Closed Caption broadcast, the closed captions will disappear.

-40 − +40

Description

Selecting the Background

Image

Selectable items Description

Logo Sharp logo screen

Blue Blue screen

None —

Selecting the Setup Guide

Selectable items Description

On Displaying the Setup Guide

Off Not displaying the Setup Guide.

when tur ning the projector on.

Menu operation n Page 36

Selecting the Wall Color

This function allows you to project the image to a colored (white or dark green) surface or wall without using a screen.

Selectable items Description

Off The Wall Color function is not

Blackboard Projects images onto a

Whiteboard Projects images onto a

Selecting the On-screen

activated.

blackboard (dark green).

whiteboard.

Display Language

Reversing/Inverting

Projected Images

Selectable items Description

Front Normal image (Projected from

Ceiling + Front Inverted image (Projected from

Rear Reversed image (Projected from

Ceiling + Rear Reversed and inver ted image

See page

18 for details of Projection (PRJ) Mode.

the front of the screen)

the front of the screen with an inverted projector)

the rear of the screen or with a mirror)

(Projected with a mirror)

The projector can switch the on-screen display language among 18 languages.

English Deutsch Español Nederlands Français Italiano Svenska Português

polski Magyar Türkçe

Tiếng Việt

Features

Useful

Adjusting the Projector Function (“PRJ-ADJ1/2” Menu)

Q PRJ-ADJ1

Pict. SCR PRJ-ADJ1SIG PRJ2

Auto Sync On

Auto Power Off On

Auto Restart On Speaker On

Fan Mode Normal System Lock

6 7

SEL./ADJ. ENTER END

Auto Sync (Auto Sync

Disable OffKeylock

Adjustment)

Selectable

items

On Auto Sync adjustment will occur when

Off Auto Sync adjustment is not

the projector is turned on or when the input signals are switched, when connected to a computer.

automatically performed.

Note

•

Auto Sync adjustment is also performed by pressing AUTO SYNC.

•

The Auto Sync adjustment may take some time to complete, depending on the image of the computer connected to the projector.

•

When the optimum image cannot be achieved with Auto Sync adjustment, use manual adjustments. (See page

Auto Power Off Function

Selectable

items

On When no input signal is detected for

Off The Auto Power Of f function will be

more than 15 minutes, the projector will automatically enter Standby mode.

disabled.

Note

When the Auto Power Off function is set to

• “On”, 5 minutes before the projector enters Standby mode, the message “Enter STANDBY mode in X min.” will appear on the screen to indicate the remaining minutes.

Description

41.)

Description

Q PRJ-ADJ2

Menu operation n Page 36

Pict. SCR PRJ-ADJ2SIG

Quick Start Menu On

FUNCTION Button Input Search STANDBY Mode Quick Start

DLP

Link

Link TM Invert

DLP

All Reset

SEL./ADJ. ENTER END

Auto Restart Function

Selectable

items

Off The projector does not turn on

Selectable

items

On The audio signal is output from the

Off The audio signal is not output from the

If the power cord is unplugged f rom the outlet or the breaker switch is turned of f when the projector is on, then the projector automatically turns on when the power cord is plugged into the AC outlet or the breaker switch is turned on.

automatically when the power cord is plugged into the AC outlet or the breaker switch is turned on.

Speaker Setting

internal speaker.

Fan Mode Setting

PRJ1

Off

0 min0Lamp Timer(Life) 100%

Description

This function changes the fan rotation speed.

Selectable

items

Normal Suitable for normal environments.

High Set when using the projector at

altitudes of approximately 1,500 meters (4,900 feet) or more.

When “Fan Mode” is set to “High”, the fan rotation speeds up, and the fan noise becomes louder.

Description

System Lock Function

This function prevents unauthorized use of the projector. Once this function is activated, users must enter the correct keycode each time the projector is turned on. We suggest

you record the keycode in a safe place where only authorized users have access.

Info

If you lose or forget your keycode, contact

• your nearest Sharp Authorized Projector Dealer or Service Center (see page if the product warranty is valid, the keycode reset will incur a charge.

a

Setting/Changing the Keycode

Select “System Lock”, then press

ENTER or Q.

Select “Next”, then press ENTER.

•

The screen for entering the keycode appears.

Press the 4 buttons on the remote

control or on the projector to enter

69). Even

the preset keycode in “Old Code”.

When setting the keycode for the ﬁ rst time,

•

press R on the projector for four times.

Setting the System Lock

Old Code

New Code Reconﬁrm

Note

If you input a wrong keycode, the cursor returns to

• the ﬁ rst point of the “Old Code”. The preset keycode is 4 R buttons on the

• projector. When you press the R button four times, the keycode input screen disappears.

PRJ - ADJ1

––––

–––– ––––

Menu operation n Page 36

Press the 4 buttons on the remote

control or on the projector to enter the new keycode in “New Code”.

Note

You cannot use the following buttons

•

for keycode: STANDBY/ON, ON,

STANDBY, ENTER, RETURN and MENU System Lock function recognizes

• each button on the remote control or on the projector as an individual button, even if they share the same button name. If you used the buttons on the projector in setting your keycode, the keycode cannot be canceled with the remote control.

Setting the System Lock

Old Code

New Code

Reconﬁrm

Enter the same keycode in “Re-

conﬁ rm”.

Note

To cancel the keycode that you have already set

Press R on the projector for four times in

• steps 4 and 5 above.

When the System Lock is set

When System Lock is set, the keycode input

• screen appears after the power is turned on. When it appears, enter the right keycode to start projection.

Input screen for keycode

System Lock

PRJ - ADJ1

****

– ––– ––––

––––

Features

Useful

Adjusting the Projector Function (“PRJ-ADJ1/2” Menu) (Continued)

Menu operation n Page 36

Keylock Function

Use this function to lock the operation buttons on the projector. This function can be set using either the menu screen or ENTER on the projector.

a

Setting with the menu screen

Taking the Keylock Off

Hold down ENTER on the projector for about 5 seconds.

On-screen display

Selectable

items

On All buttons on the projector, except

Off Turns of f the Keylock function.

a

Setting with the projector buttons

STANDBY/ON, are locked.

Description

Locking the Operation Buttons

Hold down ENTER on the

projector for about 5 seconds while the projector is being turned on.

•

The Keylock function screen is displayed.

Use this function to lock the operation buttons on the projector. (Except STANDBY/ON button)

Note: You can release the keylock by holding down ENTER on the projector for about 5 seconds.

Return

SEL. ENTER END

Select “On”, then press

On-screen display

PRJ - ADJ1

ENTER

Info

•

Even when Keylock function is set to “On”, STANDBY/ON on the projector can be used to turn on and of f the power.

•

Keylock cannot be set while the projector is: displaying the “Setup Guide” or “Menu” screens, in Standby mode, warming up, changing input signals, operating the Auto Sync or Input Search function, in Freeze mode or on the “System Lock” screen during warming up.

•

The Keylock function does not affect the operation with the remote control buttons. You cannot use the Keylock function while the

• projector is warming up.

Selecting the Quick

Start Menu

Selectable items Description

On Pressing MENU displays the

Off Pressing MENU displays the

Setting the FUNCTION

Button Operation

You can assign one of the following functions to the FUNCTION button on the remote control. The assigned function can be performed by just pressing FUNCTION.

Selectable items Description

Input Search Automatically searches for and

Audio Mute For temporarily turning of f the

Image Shift For moving the proje cted image

Signal Info

STANDBY Mode

Quick Start Menu screen.

Complete Menu screen.

switches to the appropriate Input mode.

sound. Press FUNCTION again to turn on the sound

vertically. (See page

Input signal information is displayed.

43.)

Menu operation n Page

Returning to the Default

Settings

This function allows you to initialize the settings you have made in the projector.

Note

•

The following items or menu cannot be initialized.

- Resolution

- Language

- Lamp Timer (Life)

- System Lock

Checking the Lamp

Life Status

You c an c o nﬁ rm the cumulative lamp usage time and the remaining lamp life (percentage).

Lamp usage condition Remaining lamp life

“Life” 100% 5%

Operated exclusively with “Eco+Quiet” set to “On”

Operated exclusively with “Eco+Quiet” set to “Off ”

Approx. 5,000 hours

Approx. 3,000 hours

Approx. 250 hours

Approx. 150 hours

Selectable

items

Eco Power consumption is reduced in

Quick Start The period of startup time is reduced.

See “Using 3D Viewing Mode” on page 52 for details.

DLP

Standby mode.

Link

LinkTM Invert

Description

Note

•

It is recommended that the lamp be changed when the remaining lamp life becomes 5%. The lamp life may var y depending on the

• usage condition.

Features

Useful

Viewing Stereoscopic 3D Images

Precautions on Viewing Stereoscopic 3D Images

Before viewing stereoscopic 3D images, please read this section carefully.

WARNING

■

Under normal conditions, viewing stereoscopic 3D images is safe for any duration that you would normally view your screen. However, some people may experience discomfor t. The following precautions are recommended to minimize the potential for experiencing visual problems or any adverse symptoms. Take regular breaks, at least 5 to 15 minutes after every 30 to 60 minutes of stereoscopic 3D

■

viewing.

* Based on the guidelines issued by the 3D Consortium revised December 10, 2008.

Maintain an appropriate distance from the screen. Viewing from too close a distance can strain

■

your eyes. If you experience eye strain, immediately discontinue viewing. If you experience any of the following symptoms during viewing:

• nausea, queasiness/dizziness, headache, blurr y vision or double vision that lasts longer than few seconds

Do not engage in any potentially hazardous activity (for example, driving a vehicle) until your symptoms have completely gone away. If symptoms persist, discontinue use and do not resume stereoscopic 3D viewing without discussing your symptoms with a physician.

As you get more comfortable viewing stereoscopic 3D:

•

• Adjust the parallax on the 3D-video playback equipment. (You may not be able to adjust the parallax on some models of equipment.)

• Adjust the projected image to the most comfortable viewing size by zooming.

(Projecting images on the smallest or largest screen size possible may eliminate the stereoscopic

effect and strain your eyes.)

• Use the DLP details on using “DLP® Link™ Invert”, see the section on its operation in this operation manual.)

■

The following people should limit stereoscopic 3D viewing: – Children under 6 years of age (to protect the eye growth process) – People with a histor y of photosensitivity – People with hear t disease – People in poor health – People who are sleep deprived – People who are physically tired – People under the inﬂuence of drugs or alcohol

Link™ Invert function to properly set the video for your left and right eyes. (For

Epilepsy

■

A small percentage of the population may experience epileptic seizures when viewing certain types of images that contain ﬂ ashing patterns of light.

IF YOU OR ANY MEMBER OF YOUR FAMILY HAS A HISTORY OF EPILEPSY

The following people should consult a physician before viewing stereoscopic 3D images. – Anyone with a history of epilepsy, or who has a family member with a history of epilepsy – Children under 6 years of age – Anyone who has ever experienced epileptic seizures or sensory disturbances triggered by

ﬂ ashing light effects

SOME LIGHT PATTERNS MAY INDUCE SEIZURES IN PERSONS WITH NO PRIOR HISTORY OF EPILEPSY

Discontinue use if you experience any of the following symptoms while viewing stereoscopic 3D images. – Involuntary movements, eye or muscle twitching – Muscle cramps – Nausea, dizziness, or queasiness – Convulsions – Disorientation, confusion, or loss of awareness of your surroundings

Information on the 3D Projection Function

•

To display 3D images, this projector requires:

WHAT YOU WILL NEED

1) Source devices that support the ﬁeld sequential format – For details on the supported signals, see the Compatibility Chart in this operation manual.

2) 3D LCD shutter glasses that support the DLP – Contact your nearest Sharp Authorized Projector Dealer for purchasing details.

* DLP

•

The projected image may become dark when using the 3D projection function (with “DLP set to “On”).

•

When “DLP available at all. – Keystone/Resize/Magnify

•

3D formats except for the ﬁeld sequential method, such as ones used for Blu-ray 3D or DVD prepackaged media, are not compatible with this projector. (As of March 2012)

If the power of your left and right eyes greatly differs and you primarily use one eye for viewing the

•

images, the images will not appear in 3D. In addition, images may be dif ﬁcult to view in 3D or images may not be able to be viewed in 3D depending on the individual or the content being displayed. The stereoscopic effect varies with the individual.

3D viewing is possible within the range that the 3D LCD shutter glasses are able to receive light

•

signals reﬂected by the screen. However, most 3D images are manufactured to be viewed from directly in front of the screen, so 3D viewing is recommended directly in front of the screen as much as possible. – The range for receiving signals varies depending on the 3D LCD shutter glasses. For details, see

the operation manual of your 3D LCD shutter glasses.

3D images may not be able to be played back correctly on your computer.

•

Link™ is a trademark of Texas Instruments.

Link™” is set to “On”, the following functions may not work fully or may not be

Link™* system

Appendix

■

How the 3D Projection Function (DLP Link™ ) Works The 3D projection function of this projector is compatible with the DLP 3D images, you use a pair of 3D LCD shutter glasses that alternately display the projected images for the lef t and right eyes and are synchronized with a control (light) signal.

Link™ system. To watch

Link™ ”

Shutter glasses

control light signal*

* The control light signal is transmitted from the lens of the projector, reﬂ ected by the screen, and

received by the light reception sensor on the 3D LCD shutter glasses. Therefore, the range of 3D viewing varies depending on the speciﬁ cations of the 3D LCD shutter glasses (light signal receiving sensitivity).

For details, see the operation manual of your 3D LCD shutter glasses.

Features

Useful

Viewing Stereoscopic 3D Images (Continued)

Press 3D MODE on the remote

Using 3D Viewing Mode

Use the following procedure to project 3D images.

For operation of the 3D LCD shutter glasses and the 3D-video playback equipment, see the corresponding operation manual.

ENTER button

control to display the 3D MODE menu.

Info

•

If “An invalid button has been pressed.” is displayed, a 3D-compatible signal is not being input. Check the output signal on the playback equipment.

Press Q to set “DLP® Link™” to

“On”.

O/Qbuttons

3D MODE button

Projecting 3D images

Turn the projector on.

Turn the 3D-video playback

equipment on.

Set the 3D-video playback equipment so

• that it outputs one of the signals listed in the Compatibilit y Chart in this operation manual.

Switch the Input mode of the

projector to enable input of 3D video signals.

Operate the 3D-video playback

equipment and play back the 3D content.

Press ENTER to switch the mode

and enable more natural 3D image viewing.

Warning!

If the projector, 3D-video playback

• equipment, and 3D LCD shutter glasses are not properly set, you may experience eye strain in addition to not being able to view the images in 3D.

Press 3D MODE.

The 3D MODE menu will disappear.

•

Note

If the images are not displayed in 3D, repeat

• steps 6 to 8. You can also use “DLP

• Link™ Invert” on the menu screen to change the 3D setting.

Link™” and “DLP

Ending 3D projection

Press 3D MODE on the remote

control to display the 3D MODE menu.

Turn the 3D LCD shutter glasses

on and place them over your eyes.

Press O to set “DLP® Link™” to

“Off”.

Press 3D MODE.

The 3D MODE menu will disappear.

•

Maintenance

Cleaning the projector

Ensure that you have unplugged the power

■

cord before cleaning the projector. The cabinet as well as the operation panel is

■

made of plastic. Avoid using benzene or thinner, as these can damage the ﬁ nish on the cabinet. Do not use volatile agents such as

■

insecticides on the projector. Do not attach rubber or plastic items to the projector for long periods. The effects of some of the agents in the plastic may cause damage to the quality or ﬁ nish of the projector. Wipe off dirt gently with a soft ﬂ annel cloth.

■

Using a chemical cloth (wet/dry sheet type cloth, etc.) may deform the components of the cabinet or cause cracking. Wiping with a hard cloth or using strong

■

force may scratch the cabinet surface. When the dirt is hard to remove, soak a cloth

■

in a mild detergent diluted with water, wring the cloth well and then wipe the projector. Strong cleaning detergents may discolor, warp or damage the coating on the projector. Make sure to test on a small, inconspicuous area on the projector before use.

Mild detergent

Cleaning the lens

Use a commercially available blower or lens

■

cleaning paper (for glasses and camera lenses) for cleaning the lens. Do not use any liquid type cleaning agents, as they may wear off the coating ﬁ lm on the surface of the lens. As the surface of the lens can easily get

■

damaged, be careful not to scrape or hit the lens.

Caution

•

Do not use any glass cleaner to clean the lens.

•

Avoid touching the lens with your hands to prevent ﬁ ngerprints on or damage to the lens surface.

Cleaning the exhaust and intake vents

■

Use a vacuum cleaner to clean dust from the exhaust vent and the intake vent.

Mild detergent diluted

with water

Info

•

Thinner

Wax

If you want to clean the air vents during projector operation, ensure you press

STANDBY/ON on the projector or STANDBY on the remote control and put the

projector into Standby mode. Af ter the cooling fan has stopped, clean the vents.

Appendix

Maintenance Indicators

The warning lights (power indicator, lamp indicator and temperature warning indicator) on the

■

projector indicate problems inside the projector. If a problem occurs, either the temperature warning indicator or the lamp indicator will

■

illuminate red, and the projector will enter Standby mode. After the projector has entered Standby mode, follow the procedures given below.

Top V i ew

About the temperature warning indicator

If the temperature inside the projector increases, due to blockage of the air vents, or the setting location, the temperature warning indicator will blink. And if the temperature keeps on rising, “

” will illuminate in the lower left corner of the picture with the temperature warning indicator blinking. If this state continues, the lamp will turn off, the cooling fan will run and then the projector will enter Standby mode. When you ﬁ nd the temperature warning indicator blinking, be sure to perform the measures described on page

About the lamp indicator

Temperature warning indicator

Lamp indicator

Power indicator

55.

When the remaining lamp life becomes 5% or less, (yellow) and “Change The Lamp” will

■

be displayed on the screen. When the percentage becomes 0%, it will change to (red), the lamp will automatically turn off and then the projector will automatically enter Standby mode. At this time, the lamp indicator will illuminate in red.

If you try to turn on the projector a fourth time without replacing the lamp, the

■

projector will not turn on.

Indicators on the Projector

Power indicator Red on Normal (Standby)

Green on Normal (Power on) Red blinks Abnormal (See page Green blinks Normal (Cooling)

Lamp indicator Green on Normal

Green blinks The lamp is warming up.

Temp er atu re warning indicator

Red on The lamp is shut down abnormally or requires to be

Off Normal Red on/Red blinks The internal temperature is abnormally high. (See page

changed. (See page

55.)

Maintenance indicator

Temperature

warning

indicator

Lamp

indicator

Power

indicator

Green on

when the

Green on/

(Cooling)

Normal Abnormal

Off Red blinks

(Green

blinks

lamp is

warming

up.)

Red on

Green blinks

(On)/

Red on

(Standby)

Red on The lamp does

Red on

(Standby)

Red blinks The power

Problem Cause Possible Solution

The internal temperature is abnormally high.

not illuminate.

Time to change the lamp.

The lamp does not illuminate.

indicator blinks in red when the projector is on.

Temperatures

• around the projector are high. Blocked air intake

•

Cooling fan

• breakdown Internal circuit failure

• Clogged air intake

•

The lamp is shut

• Disconnect the power cord down abnormally.

Remaining lamp life

• Carefully replace the lamp. becomes 5% or less.

Burnt-out lamp

• Lamp circuit failure

•

The lamp unit cover

• If the power indicator blinks is open.

Use the projector in an

• area with a temperature of lower than 95°F (+35ºC). Relocate the projector to

• an area with proper ventilation. (See page

•

Take the projector to your nearest Sharp Authorized Projector Dealer or Service Center (see page repair.

• from the AC outlet, and then connect it again.

• (See page Take the projector to your

• nearest Sharp Authorized Projector Dealer or Service Center (see page repair. Please exercise care when

• replacing the lamp. Securely install the cover.

•

• in red even when the lamp unit cover are securely installed, contact your nearest Sharp Authorized Projector Dealer or Service Center (see page advice.

56.)

8.)

69) for

Info

•

If the temperature warning indicator illuminates, and the projector enters Standby mode, follow the possible solutions above and then wait until the projector has cooled down completely before plugging in the power cord and turning the power back on. (At least 10 minutes.)

•

If the power is turned off for a brief moment due to power outage or some other cause while using the projector, and the power supply recovers immediately after that, the lamp indicator will illuminate in red and the lamp may not be lit. In this case, unplug the power cord from the AC outlet, replace the power cord in the AC outlet and then turn the power on again.

•

The cooling fan keeps the internal temperature of the projector constant and this function is controlled automatically. The sound of the cooling fan may change during operation because the fan speed may change and this is not a malfunction.

Appendix

Regarding the Lamp

Lamp

It is recommended that the lamp (sold separately) be replaced when the remaining lamp life becomes

■

5% or less, or when you notice a signiﬁ cant deterioration in the picture and color quality. The lamp life (percentage) can be checked with the on-screen display. (See page Purchase a replacement lamp of type AN-LX20LP from your place of purchase, nearest Sharp

■

Authorized Projector Dealer or Service Center.

IMPORTANT NOTE TO U.S. CUSTOMERS:

The lamp included with this projector is backed by a 90-day parts and labor limited warranty. All service of this projector under warranty, including lamp replacement, must be obtained through a Sharp Authorized Projector Dealer or Service Center. For the name of the nearest Sharp Authorized Projector Dealer or Service Center, please call toll-free: 1-888-GO-SHARP (1-888-467-4277).

Hg LAMP CONTAINS MERCURY For State Lamp Disposal Information www.lamprecycle.org or 1-800-BE-SHARP

Caution Concerning the Lamp

■

This projector utilizes a pressurized mercury lamp. A loud sound may indicate lamp failure. Lamp failure can be attributed to numerous sources such as: excessive shock, improper cooling, surface scratches or deterioration of the lamp due to a lapse of usage time. The period of time up to failure largely varies depending on the individual lamp and/or the condition and the frequency of use. It is impor tant to note that failure can often result in the bulb cracking. When the lamp replacement indicator and on-screen display icon are illuminated, it is recommended

■

In such a case, it is recommended you contact your nearest Sharp Authorized Projector Dealer or Service Center to assure safe operation. Should the lamp break, the glass particles may spread inside the lamp cage or gas contained in the

■

49.)

U.S.A ONLY

Replacing the Lamp

Caution

•

Do not remove the lamp unit from the projector right after use. The lamp will be very hot and may cause burns or injury. Wait at least one hour after the power cord is disconnected to allow the surface of the lamp unit to fully

• cool before removing the lamp unit.

Carefully change the lamp by following the instructions described in this section.

■

* If you wish, you may have the lamp replaced at your nearest Sharp Authorized Projector

Dealer or Service Center.

* If the new lamp does not light af ter replacement, take your projector to the nearest Sharp Authorized Projector

Dealer or Service Center for repair.

Removing and Installing the

Lamp Unit

Warning!

•

Do not remove the lamp unit from the projector right af ter use. The lamp and parts around the lamp will be very hot and may cause burns or injury.

Info

•

Do not touch the glass surface of the lamp unit or the inside of the projector.

•

To avoid injury to yourself and damage to the lamp, make sure you carefully follow the steps below. Do not loosen other screws except for the

• lamp unit cover and lamp unit.

Press STANDBY/ON on the

projector or STANDBY on the remote control to put the projector into Standby mode.

Disconnect the power cord.

•

Unplug the power cord from the AC socket.

•

Leave the lamp until it has fully cooled down (about 1 hour).

Optional

accessory

AC socket

Lamp unit

AN-LX20LP

STANDBY/ON button

Remove the lamp unit cover.

•

Loosen the user service screw (1) that secures the lamp unit cover. Slide the lamp unit cover in the direction of the arrow and then lif t it up (2).

User service screw

User service screw (for lamp unit cover)

(for lamp unit cover)

Appendix

Regarding the Lamp (Continued)

Remove the lamp unit.

•

Loosen the securing screw from the lamp unit. Hold the lamp unit and pull it in the direction of the arrow. At this time, keep the lamp unit horizontal and do not tilt it.

Insert the new lamp unit.

•

Press the lamp unit ﬁ rmly into the lamp unit compar tment to align the lamp connectors. Fasten the securing screw.

Replace the lamp unit cover.

•

Slide the lamp unit cover horizontally back into place and align the tabs (1). Then tighten the user service screw (2) to secure the lamp unit cover.

Info

•

If the lamp unit and lamp unit cover are not correctly installed, the power will not turn on, even if the power cord is connected to the projector.

Securing screw

Resetting the Lamp Timer

Reset the lamp timer after replacing the lamp.

Info

•

Make sure to reset the lamp timer only when replacing the lamp. If you reset the lamp timer and continue to use the same lamp, this may cause the lamp to become damaged or explode.

Connect the power cord.

•

Plug the power cord into the AC socket of the projector.

Reset the lamp timer.

•

While simultaneously holding down MENU, ENTER and press STANDBY/ON on the projector and keep all four buttons pressed down until the lamp indicator starts blinking green. “LAMP 0000H” is displayed, indicating

• that the lamp timer is reset.

R on the projector,

AC socketAC socket

STANDBY/ON

STANDBY/ON button

button

ENTER button

MENU button

R button

RS-232C Speciﬁ cations and Commands

Computer control

A computer can be used to control the projector by connecting an RS-232C serial control cable (cross type, commercially available) to the projector. (See page

Communication conditions

Set the serial port settings of the computer to match that of the table. Signal format: Conforms to RS-232C standard. Parity bit: None Baud rate: 9,600 bps Stop bit: 1 bit Data length: 8 bits Flow control: None

Basic format

Commands from the computer are sent in the following order: command, parameter, and return code. After the projector processes the command from the computer, it sends a response code to the computer.

Command format

C1 C2 C3 C 4 P1 P2 P3 P4

Command 4-digit Parameter 4-digit

Return code (0DH)

22.)

Response code format

Normal response

Return code (0DH)

Problem response (communication error or incorrect command)

ERR

Return code (0DH)

Info

•

When controlling the projector using RS-232C commands from a computer, wait for at least 30 seconds after the power has been turned on, and then transmit the commands.

•

After sending an input selection or picture adjustment command and then receiving an “OK” response code, the projector may take some time to process the command. If a second command is sent while the projector is still processing the ﬁ rst command, you may receive an “ERR” response code. If this happens, try resending the second command.

•

When more than one code is being sent, send each command only after the response code for the previous command from the projector is veriﬁ ed.

•

“POWR????”, “TABN _ _ _ 1”, “TLPS _ _ _ 1”, “TPOW _ _ _ 1”, “TLPN _ _ _ 1”, “TLTT _ _ _ 1”, “TLTM _ _ _ 1”, “TLTL _ _ _ 1”, “TNAM _ _ _ 1”, “MNRD _ _ _ 1”, “PJN0 _ _ _ 1”

− When the projector receives the special commands shown above: * The on-screen display will not disappear. * The “Auto Power Of f” timer will not be reset.

− The special commands are available for applications that require continuous polling.

Note

•

If an underbar (_) appears in the parameter column, enter a space.

•

If an asterisk (*) appears in the parameter column, enter a value in the range indicated in brackets under Control Contents.

Appendix

RS-232C Speciﬁ cations and Commands (Continued)

Commands

Example: When turning on the projector, make the following setting.

Computer Projector

POWR___1

CONTROL CONTENTS COMMAND PARAME TER

Power

Projector Condition

Lamp

Name

Input Change

Volum e

Keystone AV Mut e

Freeze

Auto Sync Resize COMPUTER

On POWR Off POWR Status POWR????10

Status TLPS

Power Status TPOW Quantity TLPN Usage Time(Hour) TLTT Usage Time(Minute) TLTM Life(Percentage) TLTL Model Name Check TNAM Model Name Check MN RD Projec tor Name Se tting 1

(First 4 c haracters) *1 Projec tor Name Se tting 2

(Middl e 4 charac ters) *1 Projec tor Name Se tting 3

(Last 4 c haracte rs) *1 Projector Name Check PJN0 COMPUTER I RGB HDMI I RGB VIDEO IVED Input RGB Check I RGB????1: COMPU TER

Input Video Check I VED????1: VIDEO , ERR ERR Input Mode Check IMOD????1: RGB, 2: VI DEO ER R Input Check I CHK????1: C OMPUT ER,

Volume(0 – 6 0) VOL A__**OK or ERR ERR Volume up/do wn(-10 – +10) VOUD

-80 – +80 KEYS****OK or ERR ERR On IMBK Off IMBK On FREZ Off FREZ Start ADJ S

HDMI

Normal RASR 16:9 RASR Native RASR Full RASR Border RASR Area Zoom RASR__10OK or ERR ERR V-Stretch RASR__11OK or ERR ERR Normal RBSR 16:9 RBSR Native RBS R Full RBS R Border RBSR Area Zoom RBSR__10 V-Stretch RBSR__11OK or ERR ERR

___ ___

TABN

PJN1****OK or ERR

PJN2****OK or ERR

PJN3****OK or ERR

___

___ ___ ___ ___ ___ ___ ___

___ ___ ___ ___

***OK or ERR ERR

___ ___ ___ ___ ___ ___ ___ ___ ___ ___

___ ___ ___ ___ ___

→

←

RETURN

Power ON

1 OK or ERR OK 0 OK OK or ERR

1 0: Normal

1: Tem p Hig h 8: Lamp Li fe 5% or les s 16: Lamp Bur n-out 32: Lamp Ig nition Failure

1 0: Of f, 1: On, 2: Retry

3: Waiting, 4: Lamp Error

1 1: On, 2: Cool ing 0: S tandby 1 1 1 0 – 9999(Integer) 1 0, 15, 30, 45 1 0% – 100%(Inte ger) 1 PGLW2000 1 PG-LW2000

1 Projector Name 1 OK or ERR ERR 2 OK or ERR ERR 1 OK or ERR ERR

2: HDMI, ER R

2: HDMI, 3: VID EO

1 OK or ERR ERR 0 OK or ERR ERR 1 OK or ERR ERR 0 OK or ERR ERR 1 OK or ERR ERR 1 OK or ERR ERR 2 OK or ERR ERR 3 OK or ERR ERR 5 OK or ERR ERR 6 OK or ERR ERR

1 OK or ERR ERR 2 OK or ERR ERR 3 OK or ERR ERR 5 OK or ERR ERR 6 OK or ERR ERR

OK or ERR ERR

(or 30- second start up time)

0: Normal 1: Tem p Hig h 2: Fan Error 4: Cover Ope n 8: Lamp Li fe 5% or less 16: Lamp Bur n-out 32: Lamp Ig nition Failure 64:

0: Off, 4: La mp Error

ERR

Standby mode

Temp Abnormally High

CONTROL CONTENTS COMMAND PARAME TER

Resize VIDEO

All Reset

COMPUTER Input Picture Mode

Contra st -30 – +30 RAP I_***OK or ERR ERR Bright -30 – +30 RABR_***OK or ERR ERR Red - 30 – +30 RARD_***OK or ERR ERR Blue -30 – +30 RABE_***OK or ERR ERR Color -30 – +30 RACO_***OK or ERR ERR Tint -30 – +30 RA T I_***OK or ERR ERR Sharp -30 – +30 RA SH_***OK or ERR ERR CLR Temp -1 – +1 RACT__**OK or ERR ERR Brilli antCol or™ 0 – +2 RAWE Film Mode

DNR

Picture R eset RARE

Signal Type

HDMI Inp ut

Picture M ode

Contra st -30 – +30 RBP I_***OK or ERR ERR Bright -30 – +30 RBBR_***OK or ERR ERR Red - 30 – +30 RBRD_***OK or ERR ERR Blue -30 – +30 RBBE_***OK or ERR ERR Color -30 – +30 RBCO_***OK or ERR ERR Tint -30 – +30 RB T I Sharp -30 – +30 RB SH_***OK or ERR ERR CLR Temp -1 – +1 RBC T__**OK or ERR ERR BrilliantColor™ DNR

Picture R eset RBRE

Signal Type

Audio Input

Dynamic Range

Normal RAS V 16:9 RASV Border RASV Area Zoom RASV__10OK or ERR ERR V-Stretch RASV__11OK or ERR ERR

Standard RAPS__10OK or ERR ERR Presentation RAPS__11OK or ERR ERR Movie RAPS__12OK or ERR ERR Game RAPS__13OK or ERR ERR sRGB RAPS__14OK or ERR ERR

Auto RAFM Off RAFM Level 1 RANR Level 2 RANR Level 3 RANR

Auto IASI RGB IASI YPbPr IASI Standard RBPS__10OK or ERR ERR Presentation RB PS__11OK or ERR ERR Movie RBPS__12OK or ERR ERR Game RBPS__13OK or ERR ERR sRGB RB PS__14OK or ERR ERR

0 – +2

Level 1 RBNR Level 2 RBNR Level 3 RBNR

Auto IBSI RGB IBSI YPbPr IBSI AUDIO RB A I HDMI RBA I Auto HMBD Standard HMBD Enhanced HMB D

ALRE

RBWE

___

1 OK or ERR ERR

___

2 OK or ERR ERR

___

3 OK or ERR ERR

___

1 OK or ERR ERR

___

* ___ ___ ___ ___ ___

___

___ ___ ___

___

___ ___ ___

___

___ ___ ___ ___ ___ ___ ___ ___

OK or ERR ERR 0 OK or ER R ERR 1 OK or ER R ERR

1 OK or ERR ERR 2 OK or ERR ERR 3 OK or ERR ERR

1 OK or ERR ERR

0 OK or ERR ERR 1 OK or ERR ERR 2 OK or ERR ERR

***OK or ERR ERR

OK or ERR ERR

1 OK or ERR ERR 2 OK or ERR ERR 3 OK or ERR ERR

1 OK or ERR ERR

0 OK or ERR ERR 1 OK or ERR ERR 2 OK or ERR ERR 1 OK or ERR ERR 2 OK or ERR ERR 0 OK or ERR ERR 1 OK or ERR ERR 2 OK or ERR ERR

Power ON

(or 30- second start up time)

RETURN

Standby mode

Appendix

RS-232C Speciﬁ cations and Commands (Continued)

CONTROL CONTENTS COMMAND PARAME TER

VIDEO Inp ut Picture Mod e

Contra st -30 – +30 VAP I_***OK or ERR ERR Bright -30 – +30 VABR_***OK or ERR ERR Red - 30 – +30 VARD_***OK or ERR ERR Blue -30 – +30 VABE_***OK or ERR ERR Color -30 – +30 VACO_***OK or ERR ERR Tint -30 – +30 VA T I_***OK or ERR ERR Sharp -30 – +30 VASH_***OK or ERR ERR CLR Temp -1 – +1 VACT__**OK or ERR ERR BrilliantColor™ 0 – +2 VAWE Film Mode

DNR

C.M.S. Setti ng

C.M.S. Hue

Clock -150 – +150 INCL****OK or ERR ERR Phase -3 0 – +30 INPH_***OK or ERR ERR H-pos ition -150 – +150 IAHP****OK or ERR ERR V-posit ion -60 – +60 I AVP_***OK or ERR ERR Fine Sync Adjustment Reset IARE Image Sh ift -40 – +4 0 LNDS_***OK or ERR ERR Overscan

OSD Disp lay

Video System

Background

Eco+Quiet

Picture R eset VARE

On CMCS Off CMCS__00OK or ERR ERR

Saturation

Value

C.M.S. Al l Reset CMR E

On OVSN Off OVSN On IMD I Off IMDI Auto MES Y PAL MES Y SECAM ME SY NTSC4.43 ME SY NTSC3.58 ME SY PAL-M ME SY PAL-N ME SY PAL-6 0 MES Y Logo IMBG Blue IMBG None IMBG On THMD Off THMD

Standard VAPS__10OK or ERR ERR Presentation VAPS__11OK or ERR ERR Movie VAPS__12OK or ERR ERR Game VAPS__13OK or ERR ERR

___

Auto VAFM Off VAFM Level 1 VANR Level 2 VANR Level 3 VANR

Red CMHR_***OK or ERR ERR Yel low CMHY_***OK or ERR ERR Green CMHG_***OK or ERR ERR Cyan CMH C_***OK or ERR ERR

Blue CMH B_***OK or ERR ERR Magenta CMHM_***OK or ERR ERR Reset CMRE Red CMS R_***OK or ERR ERR Yel low CMS Y_***OK or ERR ERR Green CMSG_***OK or ERR ERR Cyan CM SC_***OK or ERR ERR Blue CMS B_***OK or ERR ERR Magenta CMSM_***OK or ERR ERR Reset CMRE Red CMV R_***OK or ERR ERR Yel low CMV Y_***OK or ERR ERR Green CMVG_***OK or ERR ERR

Cyan CM V C_***OK or ERR ERR Blue CM VB_***OK or ERR ERR Magenta CMVM_***OK or ERR ERR Reset CMRE

___ ___ ___ ___ ___

___

11OK or ERR ERR

___

___ ___

___

___ ___ ___ ___ ___ ___ ___ ___ ___

___ ___ ___ ___ ___ ___ ___ ___

Power ON

* OK or ERR ERR 0 OK or ERR ERR 1 OK or ERR ERR 1 OK or ERR ERR 2 OK or ERR ERR 3 OK or ERR ERR

1 OK or ERR ERR

2 OK or ERR ERR

3 OK or ERR ERR

4 OK or ERR ERR 1 OK or ERR ERR

1 OK or ERR ERR

1 OK or ERR ERR 0 OK or ERR ERR 1 OK or ERR ERR 0 OK or ERR ERR 1 OK or ERR ERR 2 OK or ERR ERR 3 OK or ERR ERR 4 OK or ERR ERR 5 OK or ERR ERR 6 OK or ERR ERR 7 OK or ERR ERR 8 OK or ERR ERR 1 OK or ERR ERR 3 OK or ERR ERR 4 OK or ERR ERR 1 OK or ERR ERR 0 OK or ERR ERR

RETURN

(or 30- second start up time)

Standby mode

CONTROL CONTENTS COMMAND PARAMETER

Auto Sync

Auto Power O ff

Auto Restart

STANDBY Mode

PRJ Mode

Language

Setup Gu ide

Internal Speaker

RGB Frequency Check

Fan Mode

Input Search *2 Start ISES Video S etup

Wall Colo r

Quick St art Menu

DLP

Link

DLP

LinkTM Invert

Closed Caption (For Ame ricas only)

Lamp Ti mer Rese t *3

On AADJ Off AADJ On APOW Off APOW On ARES Off ARES Quick St art MOU T Eco MOU T Reverse

Invert

English ME L A Deutsch ME LA Español MEL A Nederlands ME L A França is ME L A Italiano ME L A Svenska ME L A

Português ME L A

polski ME L A__14OK or ERR ERR Türkçe ME LA__15OK or ERR ERR

Magyar MEL A__17OK or ERR ERR

Tiếng Việt

On SEGU Off SEGU On ASPK Off ASPK Horizontal TFRQ Vert ical TFRQ Normal HLMD High HLMD

0 IRE VISU

7.5 IRE VISU Off WLCO Blackboard WL CO Whiteboard WLCO On QSMN Off QSMN Off 3DEN On 3DEN

Off CLCA CC1 CLCA CC2 CLCA

On IMRE Off IMRE On IMI N Off IMIN

ME LA

ME LA__10OK or ERR ERR ME LA__11OK or ERR ERR ME LA__12OK or ERR ERR ME LA__13OK or ERR ERR

ME LA__16OK or ERR ERR

ME LA__18OK or ERR ERR

3D I V

LPRE0001ERR OK or ERR

___

1 OK or ERR ERR

___

0 OK or ERR ERR

___

1 OK or ERR ERR

___

0 OK or ERR ERR

___

1 OK or ERR ERR

___

0 OK or ERR ERR

___

1 OK or ERR ERR

___

0 OK or ERR ERR

___

1 OK or ERR ERR

___

0 OK or ERR ERR

___

1 OK or ERR ERR

___

0 OK or ERR ERR

___

1 OK or ERR ERR

___

2 OK or ERR ERR

___

3 OK or ERR ERR

___

4 OK or ERR ERR

___

5 OK or ERR ERR

___

6 OK or ERR ERR

___

7 OK or ERR ERR

___

8 OK or ERR ERR

___

9 OK or ERR ERR

___

1 OK or ERR ERR

___

0 OK or ERR ERR

___

1 OK or ERR ERR

___

0 OK or ERR ERR

___

1 kHz(***.* or ERR) ERR

___

2 Hz(***.* or ERR) ERR

___

0 OK or ERR ERR

___

1 OK or ERR ERR

___

1 OK or ERR ERR

___

0 OK or ERR ERR

___

1 OK or ERR ERR

___

0 OK or ERR ERR

___

1 OK or ERR ERR

___

2 OK or ERR ERR

___

0 OK or ERR ERR

___

1 OK or ERR ERR

___

0 OK or ERR ERR

___

1 OK or ERR ERR

___

1 OK or ERR ERR

___

0 OK or ERR ERR

___

1 OK or ERR ERR

___

2 OK or ERR ERR

Power ON

RETURN

Standby mode

(or 30- second start up time)

*1 For setting the projector name, send the commands in the order of PJN1, PJN2 and PJN3. *2 When the next command is sent during input search, you may receive an “ERR” response code, and the input

search is canceled.

*3 The L amp Timer Reset command is available only in standby mode.

Appendix

Compatibility Chart

Computer

• Multiple signal support Horizontal Frequency: 15-110 kHz, Vertical Frequency: 45-85 Hz,

PC/MAC Mode Resolution

VGA 640 × 480

SVGA 800 × 600

XGA 1024 × 768

1280 × 720 4 5.0 60

MAC 13” VGA 640 × 480 34.9 67

MAC 19” XGA 1024 × 768 60. 2 75

MAC 21” SXGA 1152 × 870 68.7 75

WXGA

WXGA+ 1440 × 900 55.9 60

SXGA

SXGA+ 1400 × 1050

WSXGA+ 1680 × 1050 65.3 60

UXGA 1600 × 1200 75.0 60

1280 × 768 47.8 60

1280 × 800

1360 × 768 47.7 60 1366 × 768 47.8 60

1152 × 864

1280 × 960

1280 × 1024

Horizontal frequency

[kHz]

31.5 60

37.9 72

37.5 75

43.3 85

35.2 56

37.9 60

48.1 72

46.9 75

53.7 85

48.4 60

56.5 70

60.0 75

68.7 85

49.7 60

62.8 75

55.0 60

66.2 70

67.5 75

60.0 60

75.0 75

64.0 60

80.0 75

64.0 60

65.3 60

Note

Optimum image quality will be achieved by matching your computer's output resolution to the

• resolution that corresponds to “TRUE” in the “Display” column shown above.

•

When “Screen resolution” of the computer is different from the resolution displayed on the projected image, follow the procedures shown below. – Refer to “Resolution” on the “SIG-ADJ” menu and select the same resolution as the resolution in

“Screen resolution” of the computer. Depending on the computer you are using, the output signal may not be faithful to the “Screen resolution”

–

adjustment. Check the settings of the computer's signal output. If the settings cannot be changed, it is recommended that the resolution be set to the one that corresponds to “TRUE” in the “Display” column.

Pixel Clock: 12-165 MHz Sync signal: Compatible with TTL level

• Compatible with sync on green signal

Verti cal freq uency [Hz]

Analog

Support

✔✔ ✔✔ ✔✔ ✔ ✔✔ ✔✔ ✔✔ ✔✔ ✔ ✔✔ ✔✔ ✔✔ ✔ ✔✔ ✔✔ ✔✔ ✔ ✔✔ ✔✔ ✔ ✔ ✔ ✔ ✔✔ ✔ ✔✔ ✔✔ ✔✔ ✔✔ ✔ ✔ ✔ ✔ ✔

✔

Digital

Support

Compression

Intelligent Compression

Display

Upscale

TRUE

Intelligent

UpscaleMAC 16” SVGA 832 × 624 49.7 75

3D Supported Signals

Signa l Horizon tal Frequ ency (k Hz) Verti cal Freq uency (Hz )

SVGA 800 × 600

XGA 1024 × 768

WXGA

1280 × 720 1280 × 800

77.1 120

98.6 120

92.6 120

101.6 120 *

*1 Reduce d Blank ing

Note

Your computer graphics card must be able to display 3D stereoscopic signals.

• Please check with your computer/graphic card speciﬁ cations or call your computer manufacturer to ensure this capability.

Analog

Support

✔✔

DTV

Horizontal

Signal

Freque ncy (kHz)

15.7 60

15.6 50

33.8 60

480 480P 31.5 60 540P 33.8 60

576 576P 31.3 50 720P 37.5 50 720P 45.0 60

1035

Vert ical

Freque ncy (Hz)

Analog

Support

Digital

Support

✔

✔✔

✔

✔✔

✔

Horizontal

Signal

Freque ncy (kHz)

1080I

1080 1080P 27.0 24 1080P 28.1 25 1080P 33.8 30 1080P 56.3 50 1080P 67.5 60

28.1 50

33.8 60

Vert ical

Freque ncy (Hz)

Analog

Support

✔✔

Digital

Support

Digital

Support

✔

Appendix

Troubleshooting

Problem Check Page

Projector power cord is not plugged into the wall outlet.•

Power to the external connected devices is off.• –

The selected Input mode is wrong.• The AV Mute function is working.• 27 Cables are incorrectly connected to the projector.• 19–22

No picture and no sound

or projector does not

start.

Sound is heard but no

picture appears

(or picture is dark).

Dark or bluish image

Color is faded or poor.

Picture is blurred;

noise appears.

Remote control battery has run out.• 13

External output has not been set when connecting a notebook computer.

• 19 The lamp unit cover is not installed correctly.• 57, 58

Cables are incorrectly connected to the projector.• “Bright” is set to minimum position.• 39

•

Depending on the computer you are using, an image may not be projected unless the signal output setting of the computer is switched to the external output. Refer to the computer's operation manual for how to switch its signal output settings. Is “On” selected in “DLP

•

Check that “Wall Color” is conﬁ gured correctly.•

•

Image adjustments are incorrectly set.

•

Make adjustments of “Color” and “Tint ” in “Picture Mode” and lower the “BrilliantColor

(Video Input only)

•

Video input system is incorrectly set.

(COMPUTER/COMPONENT Input only)

Input signal type (RGB/Component) is incorrectly set.

•

Adjust the focus.• The projection distance exceeds the focus range.• 17

There is fog on the lens. If the projector is carried from a cold room into a

• – warm room, or if it is suddenly heated, condensation may form on the surface of the lens and the image will become blurred. Set up the projector at least one hour before it is to be used. If condensation should form, remove the power cord from the wall outlet and wait for it to clear.

(Computer Input only)

Perform “SIG-ADJ” Adjustments (“Clock” and “Phase” Adjustment)

• Noise may appear depending on the computer.

•

Cables are incorrectly connected to the projector.•

•

Volume is set to minimum.

•

When the projector is connected to an external device and the volume is set to minimum, the sound is not output even if you turn up the volume of the external device.

” value.

LinkTM”?

19–22

–

45 39

–

19–22 27

Picture appears but no

sound is heard.

Data image is not

centered.

An unusual sound is

occasionally heard from

the cabinet.

“Speaker” is set to “Of f”.

• The Audio Mute function is working.

•

Make the necessary adjustments of each item in the “SIG-ADJ” menu.•

• –

Depending on the computer you are using, the output resolution signal may be dif ferent f rom the one you have set. For details, refer to the operation manual of the computer.

• –

If the picture is normal, the sound is due to cabinet shrinkage caused by room temperature changes. This will not affect operation or performance.

46 49

Problem Check Page

Maintenance indicator on

the projector illuminates

or blinks in red.

Picture is green on

COMPUTER (YPbPr)/

HDMI ( YPbPr)

Picture is pink

(no green) on

COMPUTER (RGB)/

HDMI (RGB)

Picture is too bright and

whitish.

The cooling fan becomes

noisy.

The lamp does not light

up even af ter the

projector turns on.

The lamp suddenly turns

off during projection.

The image sometimes

ﬂ i c k e r s .

The lamp needs much

time to turn on.

Picture is dark.

The remote control

cannot be used.

See “Maintenance Indicators”.•

Change the input signal type setting.•

Image adjustments are incorrectly set.•

When temperature inside the projector increases, the cooling fan runs

• faster.

The lamp indicator is illuminating in red.

• Replace the lamp.

•

Cables are incorrectly connected to the projector or the connected equipment works improperly. If this happens frequently, replace the lamp.

•

The lamp will eventually need to be changed.

• While the remaining lamp life draws to a close, replace the lamp.

•

Operate the remote control while pointing it at the projector's remote control sensor.

•

The remote control may be too far away from the projector.

•

If direct sunlight or a strong ﬂ uorescent lamp is shining on the projector's remote control sensor, place the projector where it will not be affected by strong light.

The batteries may be depleted or inse rted incorrectly. Make sure the

• 13 batteries are inserted correctly or insert new ones.

8, 9 53, 54, 55

54, 57, 58

19–22

57 57

Appendix

Troubleshooting (Continued)

Problem Check Page

Images may appear to ﬂ icker when ﬂ uorescent light or ambient light

3D images ﬂ icker when

watching in a room.

Ghosting (a double image)

occurs without the image

appearing in 3D.

• enters your vision.

Turn off the lights.

–

Block any ambient light.

–

•

Check that you are using 3D LCD shut ter glasses that suppor t the

Link™ system.

DLP –

Be sure to use 3D LCD shutter glasses that support the DLP system.

Check that the shutters on the 3D LCD shut ter glas ses are working

• properly.

Turn the 3D LCD shut ter glasses off a nd then on again.

–

Check the batteries of the 3D LCD shutter glasses.

–

Check that the 3D LCD shutter glasses are set to 3D viewing mode.

–

Some 3D LCD shutter glasses are equipped with a special viewing mode (such as “dual view mode”) in addition to the normal 3D viewing mode. See the operation manual of your 3D LCD shutter glasses.

•

Check the settings of the projector. –

Turn the DLP

–

Use “DLP

Check whether a signal that is not supported is being input.

•

Conﬁ gure your 3D application at the correct resolution and ref resh

–

rate. Make sure you are running your 3D application in resolutions that suppor t 3D. To support 3D, your 3D application must be conﬁ gured to run at the correct settings for this projector. For details on the supported signals, see “3D Suppor ted Signals” of the Compatibility Chart.

If the projector is connected to a computer for 3D image playback,

• check that a stereoscopically-enabled application is being used.

Use the applicable software.

–

Set the applicable soft ware to the ﬁ eld sequential format.

–

Check that there are no obstructions between the screen and the 3D

• LCD shutter glasses.

Remove any obstructions.

–

Any obstr uctions may cause the glasses not to function properly causing the lenses to ﬂ icker or turn off. Do not place your hand or other objects in front of the 3D control signal sensor on the glasses.

Check whether there is a source of high intensity lighting nearby.

•

Block the light or turn it off.

–

High intensity lighting can inter fere with communication between the 3D LCD shutter glasses and the screen resulting in some ﬂ icker.

Check whether two or more projectors are projecting 3D images at the

• same time.

Use only one projector at a time.

–

Link™ function “On”.

Link™ Invert” to change the setting.

This unit is equipped with a microprocessor. Its performance could be adversely affected by incorrect operation or interference. If this should happen, unplug the Unit and plug it in again after more than 5 minutes.

–

Link™

–

For SHARP Assistance

If you encounter any problems during setup or operation of this projector, ﬁ rst refer to the “Troubleshooting” section on pages manual does not answer your question, please contact the SHARP Service departments listed below.

66 to 68. If this operation

U.S.A. Sharp Electronics Corporation

1-888-GO-SHARP (1-888-467-4277)

http://www.sharpusa.com

Canada Sharp Electronics of Canada Ltd.

http://www.sharp.ca

Mexico Sharp Electronics Corporation

(525) 716-9000 http://www.sharp.com.mx

Latin America Sharp Electronics Corp. Latin

(305) 264-2277 www.servicio@sharpsec.com http://www.siempresharp.com

Germany Sharp Electronics (Europe) GmbH

01805- 29 95 29 0,14 €/Min. aus dem dt. Festnetz,

http://www.sharp.de

U.K. Sharp Electronics (U.K.) Ltd.

08705 274277

Italy Sharp Electronics (Italy) S.P.A.

(39) 02-89595-1 http://www.sharp.it

France SHARP ELECTRONICS FRANCE

Tel: 0820 856 333 http://www.sharp.fr

Spain SHARP ELECTRONICA ESPAÑA, S.A.

902 10 13 88 servicio-soporte.es@sharp.eu http://www.sharp.es

Switzerland SHARP ELECTRONICS (SCHWEIZ)

Sharp Infoline deutsch:

Sharp Infoline français:

http://www.sharp.ch

Sweden SHARP Electronics (Nordic) AB

0200 120 800 helpdesksverige@sharp.se www.sharp.se

Norway SHARP Electronics (Nordic) AB

22 07 42 82 helpdesksverige@sharp.se www.sharp.no

Finland SHARP Electronics (Nordic) AB

(09) 146 1500 helpdesksverige@sharp.se www.sharp.ﬁ

lcdsupport@sharpsec.com

(905) 568-7140

Mexico Branch

American Group

Mobilfunkpreis max. 0,42 €/Min.

http://www.sharp.co.uk/customersupport

0848 074 277 (Montag bis Freitag von 09:00-18:00 Uhr)

0848 274 277 (Lundi jusqu'à vendredi de 09:00-18:00 heures)

Denmark SHARP Electronics (Nordic) AB

(0) 70 230 810 helpdesksverige@sharp.se www.sharp.dk

Austria SHARP Electronics (Europe) GmbH

0820 - 50 08 20 EUR 0,145/min, Anrufe aus dem

www.sharp.at

Benelux SHARP Electronics Benelux BV

0900-SHARPCE (0900-7427723)

9900-0159 Belgium http://www.sharp.nl http://www.sharp.be http://www.sharp.lu

Australia Sharp Corporation of Australia Pty.

1300-135-022 http://www.sharp.net.au

New Zealand Sharp Corporation of New Zealand

Phone: (09) 573-0111 Fax: (09) 573-0112 http://www.sharp.net.nz

Singapore Sharp-Roxy Sales (S) Pte. Ltd.

65-226-6556 ckng@srs.global.sharp.co.jp http://www.sharp.com.sg

Hong Kong Sharp-Roxy (HK) Ltd.

(852) 2410-2623 dcmktg@srh.global.sharp.co.jp http://www.sharp.com.hk

Taiwan Sharp Corporation (Taiwan)

0800-025111 http://www.sharp-scot.com.tw

Malaysia Sharp-Roxy Sales & Service Co.

(60) 3-5125678

U.A.E. Sharp Middle East Fze

971-4-81-5311 helpdesk@smef.global.sharp.co.jp

Thailand Sharp Thebnakorn Co. Ltd.

02-236-0170 svc@stcl.global.sharp.co.jp http://www.sharp-th.com

Korea Sharp Electronics Incorporated of

lcd@sharp-korea.co.kr http://www.sharpkorea.co.kr

India Sharp Business Systems (India)

(91) 11- 6431313 service@sharp-oa.com

Mobilfunknetz können teurer sein

Nederland

Ltd.

Korea

(82) 2-3660-2002

Limited

Appendix

Speciﬁ cations

Model PG-LW2000 Display devices 0.65" DLP Resolution WXGA (1280 × 800) Lens F number F 2.5 – 2.7

Input terminals HDMI ×1

Control and communication terminals

Speaker 2 W (Mono) Projection lamp 210 W Rated voltage AC 100 – 240 V Rated frequency 50/60 Hz Input current 2.7 A Power consumption Eco+Quiet

Power consumption (STANDBY Mode)

Operation temperature 41ºF to 95ºF (+5ºC to +35ºC) Cabinet Plastic Dimensions (main body only) [W × H × D] 12

Weight (approx.) 5.1 lbs. (2.3 kg)

Zoom Manual, x 1.2 Focus Manual

Computer/Component (mini D-sub 15 pin)

Video (RCA) ×1 Audio (RCA) ×1 (L/R) RS-232C (D-sub 9 pin) ×1

Off

Eco+Quiet OnAC 100 V 218 W

Quick Start AC 100 V 2.5 W

Eco AC 100 V 0.5 W

AC 100 V 267 W AC 240 V 254 W

AC 240 V 207 W

AC 240 V 2.9 W

AC 240 V 0.85 W

f = 21.8 – 25.6 mm

×1

(307 × 94 × 245 mm)

Chip ×1

/32" × 3 45/64" × 9 21/32"

As a part of policy of continuous improvement, SHARP reserves the right to make design and speciﬁ cation changes for product improvement without prior notice. The performance speciﬁ cation ﬁ gures indicated are nominal values of production units. There may be some deviations from these values in individual units.

This SHARP projector uses a DLP® chip. This very sophisticated panel contains 1,0240,000 pixels (micromirrors). As with any high technology electronic equipment such as large screen TVs, video systems and video cameras, there are certain acceptable tolerances that the equipment must conform to. This unit has some inactive pixels within acceptable tolerances which may result in inactive dots on the picture screen. This will not affect the picture quality or the life expectancy of the unit.

Dimensions

Units: inches (mm)

12 3/32 (307)

/64

(5)

3 5/32 (80)

(43.5)

/32 (245)

/64 (94)3

(47.6)

(15.5)

/32

(31.5)

/64 (102.5)

/16 (103)

/32 (129) 4 31/32 (126)

M4 M4

Screw hole specs: 75 mm × 104 mm

• Depth of mounting holes: 8 mm

• Standard screw: M4 (pitch 0.7 mm)

•

Quantity: 3

/64

(49.5)

/32

(54.5)

/64 (86)

Appendix

Index

16:9·············································································28, 29 3D MODE button ······························································ 52

Accessories ········································································3 AC socket ·········································································21 Adjustment buttons ···················································· 35, 36 Adjustment foot ································································25 All Reset ···········································································49 AREA ZOOM ····································································29 Aspect ratio ······································································28 Audio input ·······································································27 AUDIO terminal ································································· 21 Audio Mute ·······································································49 Auto Power Off ·································································46 Auto Restart ·····································································46 Auto Sync (Auto Sync adjustment) ···························· 31, 46 AUTO SYNC button··························································31 AV MUTE button ······························································· 27

Background ······································································45 Batteries ···········································································13 Blue ··················································································39 BORDER ·····································································28, 29 BREAK TIMER button ······················································30 Bright ················································································39 BrilliantColor

Clock ················································································41 Closed Caption ································································· 44 CLR Temp (Color Temperature) ········································39 C.M.S. ··············································································39 Color ·················································································39 Complete Menu ································································36 COMPUTER/ Contrast ············································································39

DLP DLP DNR ··················································································40 Dynamic Range ································································41

Eco+Quiet ··································································· 30, 40 ECO+QUIET button ··························································30 EFFECT button ·································································30 ENTER button ··································································· 35 Exhaust vent ·······························································11, 53

Fan Mode ·········································································46 Film Mode ········································································· 40 Focus ring ·········································································24 FREEZE button ·································································31 FULL ·················································································28 FUNCTION button ····························································12 FUNCTION Button setting ················································49

HDMI terminal····························································· 19-21 HEIGHT ADJUST lever ·····················································25 H-Pos ···············································································41

Image shift ········································································43 Information ·······································································36 INPUT modes ···································································27 Input Search Start ····························································36 Intake vent ··································································10, 53

Kensington Security Standard connector ························11 Keycode ··········································································47 Keylock ············································································48 KEYSTONE button ··························································26 Keystone Correction ··················································· 26, 43

Lamp ················································································56 Lamp indicator ·································································54 Lamp Timer (Life) ······························································49 Lamp unit ·········································································57 Language (on-screen display language) ··························45

·································································39

COMPONENT input terminal

LinkTM ······································································52

LinkTM Invert ····························································52

················19, 20

MAGNIFY buttons ····························································31 MENU button ···································································· 35

NATIVE ··············································································28 NORMAL ····································································28, 29

ON button ·········································································23 Optional accessories ··························································3 OSD Display ····································································44 Overscan ··········································································44

Phase ················································································ 41 Picture Adjustment ··························································38 Picture Mode ······························································ 31, 38 PICTURE MODE button ···················································31 POINTER button ·······························································30 Power cord ······································································· 21 Power indicator ································································54 PRJ-ADJ1/2 ······································································ 46 PRJ Mode ···································································18, 45

Quick Start Menu ·····························································36

Red ···················································································39 Remote control ·································································12 Remote control sensor ····················································· 13 Replacing the lamp·····················································56, 57 Resize ·········································································28, 43 RESIZE button ··································································28 Resolution·········································································41 RETURN button ································································35 RGB cable ········································································19 RS-232C terminal ·····························································22

SCR-ADJ ··········································································43 Screen Size and Projection Distance ·······························17 Security bar ······································································10 Setup Guide ·······························································24, 45 Sharp ················································································39 SIG-ADJ ···········································································41 Signal Info ········································································· 42 Signal Type ·······································································41 Speaker ············································································46 SPOT button ·····································································30 STANDBY button ······························································23 STANDBY Mode ·······························································49 STANDBY/ON button ·······················································23 Supplied accessories ·························································3 System Lock ·····································································47

Temperature warning indicator ·········································54 Tint ···················································································· 39

Video Setup ······································································42 Video System ···································································42 VIDEO terminal ·································································20 VOL (Volume) buttons ·······················································27 V-Pos ················································································41 V-STRETCH ······································································29

Wall Color ········································································· 45

Zoom ring ·········································································25

Sharp PG-LW2000 User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual

Introduction

Accessories

Contents

IMPORTANT SAFEGUARDS

Part Names and Functions

Top V i ew

Front View

Rear View (Terminals)

Inserting the Batteries

Usable Range

Easy Start

Setup and Projection

Setting Up the Projector

Video Setup

Setting Up the Projector

Standard Setup (Front Projection)

Screen Size and Projection Distance

Projection (PRJ) Mode

Ceiling-Mount Setup

Connecting the Projector to Other Equipment

Connections

Connecting the Power Cord

Controlling the Projector by a Computer

Turning the Projector On/Off

Turning the Projector On

Turning the Power Off (Putting the Projector into Standby Mode)

Image Projection

About the Setup Guide

Adjusting the Projected Image

Correcting Trapezoidal Distortion

Switching the Input Mode

Adjusting the Volume

Resize Mode

Operating with the Remote Control

Displaying and Setting the Break Timer

Displaying the Pointer

Using the Spot Function

Switching the Eco+Quiet Mode

Displaying an Enlarged Portion of an Image

Freezing a Moving Image

Selecting the Picture Mode

Menu Items

Using the Menu Screen

Menu Selections (Quick Start Menu)

Quick Start Menu

Menu Selections (Complete Menu)

Picture Adjustment (“Picture” Menu)

Selecting the Picture Mode

Adjusting the Image

Adjusting the Colors

Selecting the Film Mode

Reducing Image Noise (DNR)

Eco+Quiet

Signal Adjustment (“SIG-ADJ” Menu)

Adjusting the Computer Image

Signal Type Setting

Resolution Setting

Selecting the Dynamic Range

Setting the Video System

Setting the Video Setup

Checking the Input Signal

Adjusting the Projected Image (“SCR-ADJ” Menu)

Setting the Resize Mode

Keystone Correction

Setting the Overscan

Closed Caption

Selecting the Setup Guide

Selecting the Wall Color

Adjusting the Projector Function (“PRJ-ADJ1/2” Menu)

Auto Power Off Function

Auto Restart Function

Speaker Setting

Fan Mode Setting

System Lock Function

Keylock Function

STANDBY Mode