Sharp PG-LS2000 User Manual
DATA PROJECTOR
MODEL
PG-LX2000
PG-LS2000
Introduction Easy Start Setup
OPERATION MANUAL
(PG-LX2000 only)
Connections
Operation
Basic
Features
Useful
Appendix
IMPORTANT
• For your assistance in reporting the loss
or theft of your Projector, please record
the Model and Serial Number located on
the bottom of the projector and retain this
information.
• Before recycling the packag ing, please
ensure that you have checked the contents of the carton thoroughly against the
list of “Supplied accessories” on page
SPECIAL NOTE FOR USERS IN THE U.K.
The mains lead of this product is fi tted with a non-rewireable (moulded) plug incorporating
a 10A fuse. Should the fuse need to be replaced, a BSI or ASTA approved BS 1362 fuse
marked
of the plug, must be used.
Always refi t the fuse cover after replacing the fuse. Never use the plug without the fuse
cover fi tted.
In the unlikely event of the socket outlet in your home not being compatible with the plug
supplied, cut off the mains plug and fi t an appropriate type.
DANGER:
The fuse from the cut-off plug should be removed and the cut-off plug destroyed immediately and disposed of in a safe manner.
Under no circumstances should the cut-off plug be inserted elsewhere into a 13A socket
outlet, as a serious electric shock may occur.
To fi t an appropriate plug to the mains lead, follow the instructions below:
WARNING:
THIS APPARATUS MUST BE EARTHED.
IMPORTANT:
The wires in this mains lead are coloured in accordance with the following code:
As the colours of the wires in the mains lead of this apparatus may not correspond with
the coloured markings identifying the terminals in your plug proceed as follows:
The wire which is coloured green-and-yellow must be connected to the terminal in the
x
The wire which is coloured blue must be connected to the terminal which is marked
x
The wire which is coloured brown must be connected to the terminal which is marked
x
or and of the same rating as above, which is also indicated on the pin face
Green-and-yellow : Earth
Blue : Neutral
Brown : Live
plug which is marked by the letter E or by the safety earth symbol
or green-and-yellow.
with the letter N or coloured black.
with the letter L or coloured red.
Model No.:
Serial No.:
3.
or coloured green
IF YOU HAVE ANY DOUBT, CONSULT A QUALIFIED ELECTRICIAN.
Authorized representative responsible for the European Union Community Market
SHARP ELECTRONICS (Europe) GmbH
Sonninstraße 3, D-20097 Hamburg
ii
E.U. ONLY
Before using the projector, please read this operation manual carefully.
Introduction
Introduction
ENGLISH
There are two important reasons for prompt warranty registration of your new
SHARP Projec tor, using the REGISTRATION CARD packed with the projector.
1. WARRANTY
This is to assure that you immediately receive the full benefi t of the parts,
service and labor warranty applicable to your purchase.
2. CONSUMER PRODUCT SAFETY ACT
To ensure that you will promptly receive any safety notifi cation of inspection,
modifi cation, or recall that SHARP may be required to give under the 1972
Consumer Product Safety Act, PLEASE READ CAREFULLY THE IMPORTANT
“LIMITED WARRANTY” CLAUSE.
WARNING:
WARNING:
High brightness light source. Do not stare into the beam of light, or view
directly. Be especially careful that children do not stare directly into the
beam of light.
To reduce the risk of fi re or electric shock, do not
U.S.A . ONLY
expose this product to rain or mois ture.
See bottom of projector.
CAUTION
RISK OF ELECTRIC SHOCK.
DO NOT REMOVE SCREWS
EXCEPT SPECIFIED USER
SERVICE SCREW.
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,
NO USER-SERVICEABLE PARTS EXCEPT LAMP UNIT.
DO NOT REMOVE COVER.
REFER SERVICING TO QUALIFIED SERVICE
PERSONNEL.
The lightning fl ash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence
of uninsulated “dangerous voltage”
within the product's enclosure that may
be of suffi cient magnitude to constitute
a risk or electric shock to persons.
The exclamation point within a triangle
is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the
literature accompanying the product.
WARNING:
This is a Class A product. In a domestic environment this product may cause
radio interference in which case the user may be required to take adequate
measures.
WARNING:
The enclosed computer cable must be used with the device. The cable is
provided to ensure that the device complies with FCC Class A verifi cation.
FCC Regulations state that any unauthorized changes or modifi cations
to this equipment not expressly approved by the manufacturer could
void the user's authority to operate this equip ment.
U.S.A . ONLY
U.S.A . ONLY
1
INFORMATION
This equipment has been tested and found to comply with the limits for a Class A
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference when the equipment is
operated in a commercial environment. This equipment generates, uses, and can
radiate radio frequency energy and, if not installed and used in accordance with
the operation manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful
interference, in which case the user will be required to correct the interference at
his own expense.
U.S.A . ONLY
PRODUCT DISPOSAL
This product utilizes lamp containing a small amount of mercury.
Disposal of these materials may be regulated due to environmental
considerations. For disposal or recycling information, please contact
your local authorities, the Electronics Industries Alliance: www.eiae.org,
the lamp recycling organization www.lamprecycle.org, or Sharp at
1-800-BE-SHARP.
U.S.A . ONLY
Caution Concerning Lamp Replacement
This projector utilizes a pressurized mercury lamp. A loud sound may indicate lamp failure. Lamp
■
failure can be attributed to numerous sources such as: excessive shock, improper cooling, sur face
scratches or deterioration of the lamp due to a lapse of usage time.
The period of time up to failure largely varies depending on the individual lamp and/or the condition
and the frequency of use. It is important to note that failure can often result in the bulb cracking.
When the lamp replacement indicator and on-screen display icon are illuminated, it is recommended
■
that the lamp be replaced with a new one immediately, even if the lamp appears to be operating
normally.
Should the lamp break, there is also a possibilit y that glass particles may spread inside of the
■
projector. In such a case, it is recommended you contact your nearest Sharp Authorized Projector
Dealer or Service Center to assure safe operation.
Should the lamp break, the glass particles may spread inside the lamp cage or gas contained in the
■
lamp may be vented into the room from the exhaust vent. Because the gas in this lamp includes
mercury, ventilate the room well if the lamp breaks and avoid all exposure to the released gas. In
case of exposure to the gas, consult a doctor as soon as possible.
Caution
Do not remove the lamp unit from the projector right after use. The lamp will be very hot and may
•
cause burns or injury.
Wait at least one hour after the power cord is disconnected to allow the surface of the lamp unit to
•
fully cool before removing the lamp unit.
Do not touch the glass surface of the lamp unit or the inside of the projector.
•
Do not loosen other screws except for the lamp unit cover and lamp unit.
•
Make sure to reset the lamp timer only when replacing the lamp. If you reset the lamp timer and
•
continue to use the same lamp, this may cause the lamp to become damaged or explode.
Carefully change the lamp by following the instr uctions described on pages
■
* If you wish, you may have the lamp replaced at your nearest Sharp Authorized Projector
Dealer or Service Center.
* If the new lamp does not light af ter replacement, take your projector to the nearest Sharp Authorized
Projector Dealer or Service Center for repair.
2
56 to 58.
Accessories
Supplied accessories
Introduction
Two LR03 batteries
(“AAA” size, UM/SUM-4,
Remote control
<RRMCGB015WJSA>
Power cord*
(1) (2) (3) (4)
For U.S. and
Canada, etc.
(6' (1.8 m))
<QACCDA083WJPZ>
* Which power cords are supplied along with your projector depends on the region. Use the power
cord that corresponds to the wall outlet in your country.
Initial setup guide <TINS-F443WJZZ>
•
CD-ROM <UDSKAA137WJZZ>
•
Note
Codes in “< >” are Replacement parts codes.•
<QACCVA025WJPZ>
HP-16 or similar)
For Europe,
except U.K.
(6' (1.8 m))
For U.K. and
Singapore
(6' (1.8 m))
<QACCBA105WJPZ>
RGB cable
(6' (1.8 m))
<QCNWGA173WJPZ>
For Australia, New
Zealand and Oceania
(6' (1.8 m))
<QACCLA056WJPZ>
Optional accessories
■ Lamp unit
■ Ceiling-mount adaptor
■ Ceiling-mount bracket
■ Ceiling-mount unit
■ Ceiling-mount extension tube
■ 3 RCA to mini D-sub 15 pin cable (10n (3.0 m))
AN-LX20LP
AN-60KT
AN-XRCM30 (for U.S.A. only)
AN-TK201 <for AN-60KT>
AN-TK202 <for AN-60KT>
AN-EP101B <for AN-XRCM30>
(for U.S.A. only)
AN-C3CP2
Note
Some of the optional accessories may not be available depending on the region. Please check with
•
your nearest Sharp Authorized Projector Dealer or Service Center.
3
Contents
Preparing
Introduction
Accessories ............................................3
Contents .................................................4
IMPORTANT SAFEGUARDS ..................6
Part Names and Functions ...................10
Top View ................................................ 10
Front View .............................................. 10
Rear View (Terminals) .............................. 11
Inserting the Batteries ............................. 13
Usable Range ......................................... 13
Easy Start
Easy Start .............................................14
Setup and Projection .............................. 14
Setup
Setting Up the Projector .......................16
Video Setup............................................ 16
Setting Up the Projector ......................... 16
Standard Setup (Front Projection) ........... 16
Screen Size and Projection Distance ...... 17
Projection (PRJ) Mode ............................ 18
Ceiling-Mount Setup ............................... 18
Connections
Connecting the Projector to
Other Equipment ................................19
Connecting the Power Cord .................21
Controlling the Projector by
a Computer ........................................22
Using
Basic Operation
Turning the Projector On/Off ................23
Turning the Projector On ......................... 23
Turning the Power Off (Putting the
Projector into Standby Mode) .............. 23
Image Projection ..................................24
About the Setup Guide ........................... 24
Adjusting the Projected Image ................ 24
Correcting Trapezoidal Distortion ............ 26
Switching the Input Mode ....................... 27
Adjusting the Volume .............................. 27
Displaying the Black Screen and
Turning Off the Sound Temporarily ....... 27
Resize Mode .......................................... 28
Useful Features
Operating with the Remote Control......30
Displaying and Setting the
Break Timer ......................................... 30
Displaying the Pointer ............................. 30
Using the Spot Function ......................... 30
Switching the Eco+Quiet Mode .............. 30
Auto Sync (Auto Sync Adjustment) ......... 31
Freezing a Moving Image ........................ 31
Selecting the Picture Mode ..................... 31
Displaying an Enlarged Portion of
an Image ............................................. 31
Menu Items ...........................................32
Using the Menu Screen ........................35
Menu Selections (Quick Start Menu) .........35
Quick Start Menu .................................... 36
Menu Selections (Complete Menu) .......... 36
Picture Adjustment (“Picture” Menu) ....38
Selecting the Picture Mode ..................... 38
Adjusting the Image ................................ 39
Adjusting the Color Temperature ............. 39
Adjusting the Colors ............................... 39
Selecting the Film Mode ......................... 40
Reducing Image Noise (DNR) ................. 40
Eco+Quiet .............................................. 40
Signal Adjustment (“SIG-ADJ” Menu) ..41
Adjusting the Computer Image ............... 41
Resolution Setting .................................. 41
Signal Type Setting ................................. 41
Selecting the Dynamic Range ................. 41
Setting the Video System ....................... 42
Setting the Video Setup .......................... 42
Checking the Input Signal ....................... 42
Adjusting the Projected Image
(“SCR-ADJ” Menu) .............................43
Setting the Resize Mode ......................... 43
Adjusting the Image Position .................. 43
Keystone Correction ............................... 43
Setting the Overscan .............................. 44
Setting the On-screen Display ................ 44
Closed Caption ...................................... 44
Selecting the Background Image ............ 45
Selecting the Setup Guide ...................... 45
Reversing/Inverting Projected Images ..... 45
Selecting the Wall Color .......................... 45
Selecting the On-screen Display Language
Adjusting the Projector Function
(“PRJ-ADJ1/2” Menu) ........................46
Auto Sync (Auto Sync Adjustment) ......... 46
Auto Power Off Function ........................ 46
Auto Restart Function ............................. 46
Speaker Setting ...................................... 46
Fan Mode Setting ................................... 46
System Lock Function ............................ 47
... 45
4
Keylock Function .................................... 48
Selecting the Quick Start Menu .............. 49
Setting the FUNCTION Button Operation
STANDBY Mode ..................................... 49
®
DLP
LinkTM ............................................ 49
®
DLP
LinkTM Invert .................................. 49
Returning to the Default Settings ............ 49
Checking the Lamp Life Status ............... 49
Viewing Stereoscopic 3D Images .........50
Precautions on Viewing Stereoscopic
3D Images ........................................... 50
Information on the 3D Projection
Function .............................................. 51
Appendix ................................................ 51
Using 3D Viewing Mode ......................... 52
Reference
Appendix
Maintenance .........................................53
Maintenance Indicators ........................54
Regarding the Lamp .............................56
Lamp...................................................... 56
Caution Concerning the Lamp ................ 56
Replacing the Lamp ............................... 56
Removing and Installing the Lamp Unit ... 57
Resetting the Lamp Timer ...................... 58
RS-232C Specifi cations and Commands
Compatibility Chart ..............................64
Troubleshooting ....................................66
For SHARP Assistance .........................69
Specifi cations .......................................70
Dimensions ...........................................71
Index .....................................................72
Introduction
.. 49
...59
In this operation manual, the illustration and the screen display are simplifi ed for explanation, and
•
may differ slightly from the actual display. The examples used throughout this manual are based
on the PG-L X2000 model.
5
IMPORTANT SAFEGUARDS
CAUTION: Please read all of these instructions before you operate this
product and save these instructions for later use.
Electrical energy can perform many useful functions. This product has been engineered
and manufactured to assure your personal safety. BUT IMPROPER USE CAN RESULT IN
POTENTIAL ELECTRICAL SHOCK OR FIRE HAZARDS. In order not to defeat the
safeguards incorporated in this product, observe the following basic rules for its
installation, use and servicing.
1. Read Instructions
All the safety and operating instructions
should be read before the product is
operated.
2. Retain Instructions
The safety and operating instructions
should be retained for future reference.
3. Heed Warnings
All warnings on the product and in the
operating instructions should be adhered to.
4. Follow Instructions
All operating and use instructions should
be followed.
5. Cleaning
Unplug this product from the wall outlet before
cleaning. Do not use liquid cleaners or aerosol
cleaners. Use a damp cloth for cleaning.
6. Attachments
Do not use attachments not recommended by the
product manufacturer as they may cause hazards.
7. Water and Moisture
Do not use this product near water–for
example, near a bath tub, wash bowl, kitchen
sink, or laundry tub; in a wet basement; or
near a swimming pool; and the like.
8. Accessories
Do not place this product on an unstable
cart, stand, tripod, bracket, or table. The
product may fall, causing serious injury to a
child or adult, and serious damage to the
product. Use only with a cart, stand, tripod,
bracket, or table recommended by the
manufacturer, or sold with the product. Any
mounting of the product should follow the
manufacturer's instructions, and should use a
mounting accessory recom mended by the
manufacturer.
9. Transportation
A product and cart
combination should be
moved with care. Quick
stops, excessive force, and
uneven surfaces may
cause the product and cart
combination to overturn.
10. Ventilation
Slots and openings in the cabinet are provided
for ventilation to ensure reliable operation of
the product and to protect it from overheating,
and these openings must not be blocked or
covered. The open ings should never be
blocked by placing the product on a bed, sofa,
rug, or other similar surface. This prod uct
should not be placed in a built-in installation
such as a book case or rack unless proper
ventilation is provided or the manufacturer's
instruc tions have been adhered to.
11. Power Sources
This product should be operated only from
the type of power source indicated on the
marking label. If you are not sure of the
type of power supply to your home, consult
your product dealer or local power
company. For products intended to operate
from battery power, or other sources, refer
to the operating instructions.
12. Grounding or Polarization
This product is provided with one of the
following types of plugs. If the plug should
fail to fi t into the power outlet, please contact
your electrician.
Do not defeat the safety purpose of the plug.
a. Two-wire type (mains) plug.
b. Three-wire grounding type (mains) plug
with a grounding terminal.
This plug will only fi t into a grounding
type power outlet.
13. Power-Cord Protection
Power-supply cords should be routed so
that they are not likely to be walked on or
pinched by items placed upon or against
them, paying particular attention to cords
at plugs, convenience receptacles, and the
point where they exit from the product.
14. Lightning
For added protection for this product during
a lightning storm, or when it is left
unattended and unused for long periods of
time, unplug it from the wall outlet and
disconnect the cable system. This will
pre vent damage to the product due to
lightning and power-line surges.
6
15. Overloading
Do not overload wall outlets, extension cords,
or integral convenience receptacles as this
can result in a risk of fi re or electric shock.
16. Object and Liquid Entry
Never push objects of any kind into this
product through openings as they may touch
dangerous voltage points or short-out parts
that could result in a fi re or electric shock.
Never spill liquid of any kind on the product.
17. Servicing
Do not attempt to service this product
yourself as opening or removing covers
may expose you to dan ger ous voltage or
other hazards. Refer all servicing to
qualifi ed service personnel.
18. Damage Requiring Service
Unplug this product from the wall outlet
and refer servicing to qualifi ed ser vice
personnel under the following conditions:
a. When the power-supply cord or plug is
damaged.
b. If liquid has been spilled, or objects
have fallen into the product.
c. If the product has been exposed to rain
or water.
d. If the product does not operate normally
by following the operating instructions.
Adjust only those con trols that are
covered by the operating instructions,
as an improper adjustment of other
controls may result in damage and will
often require extensive work by a
qualifi ed technician to restore the
product to normal operation.
e. If the product has been dropped or
damaged in any way.
f. When the product exhibits a distinct
change in performance, this indicates a
need for service.
19. Replacement Parts
When replacement parts are required, be
sure the ser vice technician has used
replace ment parts specifi ed by the
manufacturer or have the same
characteristics as the original part.
Unauthorized substitutions may result in
fi re, electric shock, or other hazards.
20. Safety Check
Upon completion of any service or repairs
to this product, ask the ser vice technician
to per form safety checks to determine that
the product is in proper operating
condition.
21. Wall or Ceiling Mounting
This product should be mounted to a wall
or ceiling only as recommended by the
manufacturer.
22. Heat
This product should be situated away from
heat sources such as radiators, heat
registers, stoves, or other products
(including amplifi ers) that produce heat.
Introduction
DLP® and the DLP logo are registered trademarks of Texas Instruments and
•
BrilliantColor
PC/AT is a registered trademark of International Business Machines Corporation in the
•
United States.
Macintosh
•
TM
and DLP® LinkTM are trademarks of Texas Instruments.
®
is a registered trademark of Apple Computer, Inc. in the United States and/or
other countries.
HDMI, the HDMI logo and High-Defi nition Multimedia Interface are trademarks or
•
registered trademarks of HDMI Licensing LLC.
All other company or product names are trademarks or registered trademarks of their
•
respective companies.
•
Some IC chips in this product include confi dential and/or trade secret property belonging
to Texas Instruments. Therefore you may not copy, modify, adapt, translate, distribute,
reverse engineer, reverse assemble or discompile the contents thereof.
7
Observe the following safeguards when setting up your
projector.
Caution concerning the lamp unit
Potential hazard of glass particles if lamp
■
ruptures. In case of lamp rupture, contact
your nearest Sharp Authorized Projector
Dealer or Service Center
for replacement.
See “Regarding the Lamp”
on page
56.
Caution concerning the setup of the
projector
For minimal servicing and to maintain high
■
image quality, SHARP recommends that
this projector be installed in an area free
from humidity, dust and cigarette smoke.
When the projector is subjected to these
environments, the vents and lens must be
cleaned more often. As long as the
projector is regularly cleaned, use in these
environments will not reduce the overall
operation life of the unit. Internal cleaning
should only be per formed by a Sharp
Authorized Projector Dealer or Ser vice
Center.
Rest your eyes occasionally.
Continuously watching the screen for long
■
hours will cause eye strain. Take regular
breaks to rest your eyes.
Do not set up the projector in places
exposed to direct sunlight or bright light.
■
Position the screen so that it is not in direct
sunlight or room light. Light falling directly
on the screen washes out the colors,
making viewing diffi cult. Close the cur tains
and dim the lights when setting up the
screen in a sunny or bright room.
Caution regarding placing of the projector
■
Place the projector on a level site within the
adjustment range (9 degrees) of the
adjustment foot.
■
After the projector is purchased, a faint
smell from the vent may appear when the
power is fi rst turned on. This is normal and
is not a malfunction. It will disappear after
the projector is used for a while.
When using the projector in highaltitude areas such as mountains (at
altitudes of approximately 1,500
meters (4,900 feet) or more)
■
When you use the projector in high-altitude
areas with thin air, set “Fan Mode” to
“High”. Neglecting this can affect the
longevity of the optical system.
■
Use the projector at altitudes of 2,300
meters (7,500 feet) or less.
Warning about placing the projector in
a high position
■
When placing the projector in a high
position, make cer tain it is carefully secure
to avoid personal injury caused by the
projector falling down.
Do not subject the projector to hard
impact and/or vibration.
■
Protect the lens so as not to hit or damage
the surface of the lens.
Avoid locations with extremes of
temperature.
■
The operating temperature of the projector
is from 41°F to 95°F (+5°C to +35°C).
■
The storage temperature of the projector is
from –4°F to 140°F (–20°C to +60°C).
Do not block the exhaust and intake
vents.
■
Allow at least 11 13/16 inches (30 cm) of
space between the exhaust vent and the
nearest wall or obstruction.
■
Ensure that the intake vent and the exhaust
vent are not obstructed.
■
If the cooling fan becomes obstructed, a
protection circuit will automatically put the
projector into Standby mode to prevent
overheat damage. This does not indicate a
malfunction. (See pages 54 and 55.)
Remove the projector power cord from the
wall outlet and wait at least 10 minutes.
Place the projector where the intake and
exhaust vents are not blocked, plug the
power cord back in and turn on the
projector. This will return the projector to
the normal operating condition.
8
Caution regarding usage of the projector
■
If you are not to use the projector for a long
time or before moving the projector, make
certain you unplug the power cord from the
wall outlet, and disconnect any other
cables connected to it.
■
Do not carry the projector by holding the
lens.
■
Do not expose the projector to direct
sunlight or place next to heat sources.
Doing so may affect the cabinet color or
cause deformation of the plastic cover.
Other connected equipment
■
When connecting a computer or other
audio-visual equipment to the projector,
make the connections AFTER unplugging
the power cord of the projector from the
AC outlet and turning off the equipment to
be connected.
■
Please read the operation manuals of the
projector and the equipment to be
connected for instructions on how to make
the connections.
Using the projector in other countries
■
The power supply voltage and the shape of
the plug may vary depending on the region
or country you are using the projector in.
When using the projector overseas, make
sure you use an appropriate power cord for
the country you are in.
Temperature monitor function
If the temperature inside the projector
■
increases, due to blockage of the air vents,
or the setting location, the temperature
warning indicator will blink. And if the
temperature keeps on rising, “ ” will
illuminate in the lower left corner of the
picture with the temperature warning
indicator blinking. If this state continues,
the lamp will turn off, the cooling fan will
run and then the projector will enter
Standby mode. Refer to “Maintenance
Indicators” on pages 54 and 55 for details.
Info
The cooling fan regulates the internal
•
temperature, and its performance is automatically
controlled. The sound of the fan may change
during projector operation due to changes in the
fan speed. This does not indicate malfunction.
Introduction
Closed Caption uses Bitstream Vera fonts
Copyright (c) 2003 by Bitstream, Inc. All Rights Reser ved. Bitstream Vera is a trademark of Bitstream, Inc.
Permission is hereby granted, free of charge, to any person obtaining a copy of the fonts accompanying this
license (“Fonts”) and associated documentation fi les (the “Font Software”), to reproduce and distribute the
Font Software, including without limitation the rights to use, copy, merge, publish, distribute, and/or sell
copies of the Font Software, and to permit per sons to whom the Font Software is furnished to do so, subject
to the following conditions:
The above copyright and trademark notices and this permission notice shall be included in all copies of one
or more of the Font Sof tware t ypefaces.
The Font Software may be modifi ed, altered, or added to, and in particular the designs of glyphs or
characters in the Fonts may be modifi ed and additional glyphs or characters may be added to the Fonts,
only if the fonts are renamed to names not containing either the words “Bitstream” or the word “Vera”.
This License be comes null and void to the extent applicable to Fonts or Font Sof tware that has been
modifi ed and is distributed under the “Bitstream Vera” names.
The Font Software may be sold as part of a large r software package but no copy of one or more of the Font
Software typefaces may be sold by itself.
THE FONT SOFTWARE IS PROVIDED “AS IS”, WITHOUT WARR ANT Y OF ANY KIND, EXPRESS OR
IMPLIED, INCLUDING BUT NOT LIMITED TO ANY WARR ANTIES OF MERCHANTABILIT Y, FITNESS FOR A
PARTICULAR PURPOSE AND NONINFRINGEMENT OF COPYRIGHT, PATENT, TRADEMARK, OR OTHER
RIGHT. IN NO EVENT SHALL BITSTREAM OR THE GNOME FOUNDATION BE LIABLE FOR ANY CLAIM,
DAMAGES OR OTHER LIABILITY, INCLUDING ANY GENERAL, SPECIAL, INDIRECT, INCIDENTAL, OR
CONSEQUENTIAL DAMAGES, WHETHER IN AN ACTION OF CONTR ACT, TORT OR OTHERWISE, ARISING
FROM, OUT OF THE USE OR INABILITY TO USE THE FONT SOFTWARE OR FROM OTHER DEALINGS IN
THE FONT SOFTWARE.
Except as contained in this notice, the names of Gnome, the Gnome Foundation, and Bitstream Inc., shall
not be use d in adver tising or otherwise to promote the sale, use or other dealings in this Font Software
without prior written authoriz ation from the Gnome Foundation or Bitstream Inc., respectively. For further
information, contact: fonts at gnome dot org.
9
Part Names and Functions
Numbers in Z refer to the main pages in this operation manual where the
topic is explained.
1
2
3
4
5
8
9
6
7
Top V i e w
1 Temperature warning indicator
2 Lamp indicator
3 Power indicator
4 STANDBY/ON button
For turning the power on and putting the
projector into Standby mode.
5 ENTER button
For setting items selected or adjusted on
the menu.
6 VOL (Volume) buttons (–O/Q+)
For adjusting the speaker sound level.
7 AUTO SYNC button
For automatically adjusting images when
connected to a computer.
8 Adjustment buttons (P/R/O/Q)
For selecting menu items.
9 INPUT buttons (P/R)
For switching Input mode.
10 MENU button
For displaying adjustment and setting
screens.
54
54
35
31
35
10
54
23
27
35
27
15 16 17
Front View
11 Zoom ring
For enlarging/reducing the picture.
12 Focus ring
For adjusting the focus.
13 Intake vent
14 Security bar
15 HEIGHT ADJUST lever
16 Adjustment foot
17 Remote control sensor
25
24
53
25
25
13
11
12
13
14
10
1234 5
Rear View (Terminals)
Introduction
6
7
8
9
10
1 HDMI terminal
(PG-LX2000 only)
Terminal for HDMI input.
2 AUDIO input terminal
3 VIDEO input terminal
Terminal for connecting video equipment.
19, 20, 21
21
20
4 COMPUTER/COMPONENT input
terminal
Terminal for computer RGB and
component signals.
5 RS-232C terminal
Terminal for controlling the projector using
a computer.
6 Exhaust vent
7 Speaker
19, 20
22
53
46
8 Kensington Security Standard
connector
9 Rear adjustment foot
10 AC socket
Connect the supplied power cord.
21
25
Using the Kensington Lock
•
This projector has a Kensington Security
Standard connector for use with a
Kensington MicroSaver Security System.
Refer to the information that came with the
system for instructions on how to use it to
secure the projector.
11
Part Names and Functions (Continued)
Numbers in Z refer to the main pages in this operation manual where the
topic is explained.
1
2
3
4
5
6
7
8
9
10
11
12
1
ON button
For turning the power on.
2
STANDBY button
For putting the projector into the Standby
mode.
3
MAGNIFY buttons
For enlarging/reducing part of the image.
4
FREEZE button
For freezing images.
5
BREAK TIMER button
For displaying the break time.
6
AV MUTE button
For temporarily displaying a black screen
and turning off the sound.
7
SPOT button
For displaying the spotlight.
23
23
31
31
30
27
30
13
14
15
16
17
18
19
20
21
22
8
POINTER button
For displaying the pointer.
9
Adjustment buttons (P/R/O/Q)
For selecting and adjusting menu items.
10
EFFECT button
For changing the pointer or spot area.
11
KEYSTONE button
For entering the Keystone Correction
mode.
12
FUNCTION button
For operating and executing a function
assigned to “FUNCTION Button”.
13
VOL +/– (Volume) buttons
For adjusting the speaker sound level.
14
INPUT buttons (P/R)
For switching Input mode.
15
PICTURE MODE button
For selecting the appropriate picture.
16
AUTO SYNC button
For automatically adjusting images when
connected to a computer.
17
RESIZE button
For switching the picture size (NORMAL,
16:9, etc.).
18
MENU button
For displaying adjustment and setting
screens.
19
ENTER button
For setting items selected or adjusted on
the menu.
20
RETURN button
For returning to the previous menu screen
during menu operations.
21
ECO+QUIET but ton
For lowering the noise of the cooling fan
and extending the lamp life.
22
3D MODE button
For displaying the 3D MODE menu screen.
30
30
26
49
27
27
31
31, 46
28
35
35
35
30
52
35
12
Inserting the Batteries
3
Pull down the tab on the cover and remove the
1
cover towards the direction of the arrow.
Insert the batteries.
2
Insert the batteries making sure the polarities correctly match
•
the m and n marks inside the battery compartment.
Insert the lower tab of the cover into the opening,
3
and lower the cover until it clicks in place.
Incorrect use of the batteries may cause them to leak or explode.
Please follow the precautions below
Caution
Danger of explosion if battery is incorrectly replaced.
•
Replace only with alkaline or manganese batteries.
Inser t the batteries making sure the polarities correctly match the m and n marks inside the batter y
•
compartment.
Batteries of dif ferent types have different properties, therefore do not mix batteries of dif ferent types.
•
Do not mix new and old batterie s.
•
This may shorten the life of new batteries or may cause old batteries to leak.
Remove the batteries from the remote control once they have run out, as leaving them in can cause them to leak.
•
Batter y fl uid from leaked batteries is harmful to skin, therefore ensure you wipe them fi rst and then
remove them using a cloth.
The batteries included with this projector may run down in a short period, depending on how they are kept.
•
Be sure to replace them as soon as possible with new batteries.
Remove the batteries from the remote control if you will not be using the remote control for a long time.
•
Comply with the rules (ordinance) of each local government when disposing of worn-out batteries.
•
Introduction
Usable Range
The remote control can be used to control the
projector within the ranges shown in the
illustration.
Note
•
The signal from the remote control can be
refl ected off a screen for easy operation.
However, the effective distance of the signal
may differ depending on the screen material.
When using the remote control
Ensure that you do not drop it or expose it to
•
moisture or high temperature.
The remote control may malfunction under a
•
fl uorescent lamp. In this case, move the
projector away from the fl uorescent lamp.
Remote control
Remote control
Remote control sensor
Remote control sensor
30°
30°
30°
30°
Remote control signal
Remote control signal
transmitters
transmitters
33n (10 m)
33n (10 m)
13
Easy Start
This section shows the basic operation (projector connecting with the computer). For details,
see the page described below for each step.
Setup and Projection
In this section, connection of the projector and the computer is explained using one example.
3
STANDBY/ON
8
button
O/Q buttons
6
INPUT buttons
6
STANDBY button
8
ON button
3
INPUT buttons
6
Zoom ring
4
Focus ring
4
HEIGHT
4
ADJUST lever
1. Place the projector facing a wall or a screen
5
Adjustment
6
buttons
(P/R/O/Q)
KEYSTONE button
5
P. 16
B
2. Connect the projector to the computer and plug the power
cord into the AC socket of the projector
When connecting equipment other than a computer, see pages
20 and 21.
BPP. 19, 21
3. Turn the projector on
Press STANDBY/ON on the projector or ON on the remote control.
14
BP. 2 3
4. Adjust the projected image with the Setup Guide
1 After the projector turns on, the Setup Guide appears.
(When “Setup Guide” is set to “On”. See page
2
Follow the steps in the Setup Guide and adjust the focus, height (angle) and picture size.
45.)
3 After adjusting the focus, height (angle) and picture size, press ENTER to fi nish the
Setup Guide.
BP. 2 4
5. Correct trapezoidal distortion
Correcting trapezoidal distortion using Keystone Correction.
On the remote control
Shrinks
upper side.
Shrinks
lower side.
BP. 2 6
6. Select the Input mode
Press INPUT P/R to display the INPUT list. Use INPUT P/R to select the Input mode.
On the
projector
On the remote
control
INPUT list (e.g. PG-L X2000)
INPUT
COMPUTER
H
HDMI
V
VIDEO
Audio
Easy Start
[PG-LX2000 only]
When you select HDMI input, use O/Q to select the audio input terminal (HDMI or AUDIO).
BP. 2 7
7. Turn the computer on
8. Turn the power off
Press STANDBY/ON on the projector or STANDBY on the remote control, and then press
the button again while the confi rmation message is displayed to put the projector into
Standby mode.
On the
projector
On the remote
control
On-screen display
BP. 2 3
15
Setting Up the Projector
Video Setup
If using this projector outside the U.S.A., please change setting to “0 IRE” in Video Setup. (See
page 42.)
Setting Up the Projector
For optimal image quality, position the projector perpendicular to the screen with the projector's
feet fl at and level. Doing so will eliminate the need for Keystone correction and provide the best
image quality. (See page 26.)
Standard Setup (Front Projection)
■
Place the projector at the required distance from the screen according to the desired picture
size. (See page 17.)
Indication of the Projection Image Size and Projection Distance
Example: 4:3 Signal Input (Normal Mode)
Picture Size
300" (762 cm)
200" (508 cm)
100" (254 cm)
40" (102 cm)
32"
×
24"
(81 cm
×
80"
(203 cm
61 cm)
×
240"×180"
(610 cm × 457 cm)
160"
×
120"
(406 cm
60"
×
152 cm)
×
305 cm)
Projection
Distance
16
5'2"–6'2"
(1.6 m – 1.9 m)
12'11"–15'6"
(3.9 m – 4.7 m)
25'10"–30'11"
(7.9 m – 9.4 m)
38'9"–46'5"
(11.8 m – 14.2 m)
Screen Size and Projection Distance
Screen
Note
H
Lens center
L
4:3 Signal Input (Normal Mode)
Picture (Screen) size Projection distance [L]
Diag. [F]
Width Height Minimum [L1] Maximum [L2]
300" (762 cm) 610 cm (240") 457 cm (180") 11.8 m (38' 9") 14.2 m (46' 5")
250" (635 cm) 508 cm (200") 381 cm (150") 9.9 m (32' 4") 11.8 m (38' 8")
200" (508 cm) 406 cm (160") 305 cm (120") 7.9 m
(25' 10")
150" (381 cm) 305 cm (120") 229 cm (90") 5.9 m (19' 5") 7.1 m (23' 3")
120" (305 cm) 244 cm (96") 183 cm (72") 4.7 m (15' 6") 5.7 m (18' 7")
100" (254 cm) 203 cm (80") 152 cm (60") 3.9 m
(12' 11")
80" (203 cm) 163 cm (64") 122 cm (48") 3.2 m (10' 4") 3.8 m (12' 5")
70" (178 cm) 142 cm (56") 107 cm (42") 2.8 m (9' 1") 3.3 m
60" (152 cm) 122 cm (48") 91 cm (36") 2.4 m (7' 9") 2.8 m (9' 3")
40" (102 cm) 81 cm (32") 61 cm (24") 1.6 m (5' 2") 1.9 m (6' 2")
16:9 Signal Input (16:9 Mode)
Picture (Screen) size Projection distance [L]
Diag. [F]
300" (762 cm) 664 cm (261") 374 cm (147") 12.9 m (42' 3") 15.4 m (50' 7") 81 cm
250" (635 cm) 553 cm (218") 311 cm (123") 10.7 m (35' 3") 12.8 m (42' 2") 67 cm
200" (508 cm) 443 cm (174") 249 cm (98") 8.6 m (28' 2") 10.3 m (33' 9") 54 cm
150" (381 cm) 332 cm (131") 187 cm (74") 6.4 m (21' 2") 7.7 m (25' 3") 40 cm
120" (305 cm) 266 cm (105") 149 cm (59") 5.2 m (16' 11") 6.2 m (20' 3") 32 cm
100" (254 cm) 221 cm (87") 125 cm (49") 4.3 m (14' 1") 5.1 m (16' 10") 27 cm
80" (203 cm) 177 cm (70") 100 cm (39") 3.4 m (11' 3") 4.1 m (13' 6") 22 cm
60" (152 cm) 133 cm (52") 75 cm (29") 2.6 m (8' 5") 3.1 m (10' 1") 16 cm
40" (102 cm) 89 cm (35") 50 cm (20") 1.7 m (5' 8") 2.1 m (6' 9") 11 cm
When using the projector with screen sizes not listed in the above charts, calculate the values according to the formulas.
L1: Minimum projection distance (m/ft) 0.03941F0.03941F / 0.3048 0.04294F0.04294F / 0.3048
L2: Maximum projection distance (m/ft) 0.04717
H:
Distance from the lens center to the bottom of the image (cm/in)
Adjustable range of image position (cm/in)
S:
F
: Picture diagonal size : 40
Width Height Minimum [L1] Maximum [L2]
[m/cm] [Feet/inches] [m/cm] [Feet/inches]
0.05689F0.05689F / 2.54 0.26952F0.26952F / 2.54
''
-300
See page 43.
''
— — ±0.20754F±0.20754F / 2.54
Note
Allow a margin of error in the values in the
•
Allow a margin of error in the values in the
•
diagrams below.
diagrams below.
Distance from the lens center
9.4 m
(30' 11")
4.7 m (15' 6")
(10' 10")
to the bottom of the image [H]
Distance from the lens
center to the bottom
of the image [H]
17 cm
14 cm
11 cm
9 cm
7 cm
6 cm
5 cm
4 cm
3 cm
2 cm
(31 53/64"
23
(6
/32")
19
/32")
(5
31
/64")
(4
23
(3
/64")
11
(2
/16")
15
(2
/64")
51
/64")
(1
9
/16")
(1
11
(1
/32")
57
(
/64")
Adjustable range of
image position [S]
±62 cm
)
(2617/32")±52 cm
(21 7/32"
(15 59/64"
(12 47/64"
(10 39/64"
(831/64"
(6 23/64"
(4 1/4"
±42 cm
)
±31 cm
)
±25 cm
)
±21 cm
)
±17 cm
)
±12 cm
)
±8 cm
)
4:3 Signal 16:9 Signal
F
0.04717F / 0.3048 0.05139F0.05139F / 0.3048
(±24 33/64"
27
(±20
/64"
(±16 11/32"
(±12 1/4"
(±9 13/16"
(±8 11/64"
(±6 17/32"
(±4 29/32"
(±3 17/64"
)
Setup
)
)
)
)
)
)
)
)
17
Setting Up the Projector (Continued)
Projection (PRJ) Mode
The projector can use any of the 4 projection modes shown in the diagram below. Select the
mode most appropriate for the projection setting in use. (You can set the PRJ mode in “SCRADJ” menu. See page 45.)
Table mounted, front projection
■
[Menu item ➞ “Front”]
Table mounted, rear projection
■
(with a translucent screen)
[Menu item ➞ “Rear”]
Ceiling mounted, front projection
■
[Menu item ➞ “Ceiling + Front”]
■
Ceiling mounted, rear projection
(with a translucent screen)
[Menu item ➞ “Ceiling + Rear”]
a
Ceiling-Mount Setup
It is recommended that you use the optional Sharp ceiling-mount adaptor and unit for this
installation. Before mounting the projector, contact your nearest Sharp Authorized Projector
Dealer or Service Center to obtain the recommended ceiling-mount adaptor and unit (sold
separately).
18
Connecting the Projector to Other Equipment
Before connecting, ensure that the power cord of the projector is unplugged from the AC outlet
and turn off the equipment to be connected. After making all connections, turn on the projector
and then the other pieces of equipment. When connecting a computer, ensure that it is the last
equipment to be turned on after all the connections are made.
IMPORTANT:
Ensure that the appropriate input mode has been selected on the projector before
you turn on the connected equipment.
For more details of connection and cables, refer to the operation manual of the connecting equipment.
•
You may need other cables or connectors not listed below.
•
Terminals on the Projector
Equipment
Computer
Terminal on
connected equipment
RGB
output
terminal
RGB cable (supp lied) COMPUTER/
Cable
Terminal o n the
projector
COMPONENT
Connections
HDMI output
terminal
is only for PG-LX2000
Note
•
Depending on specifi cations of equipment or the DVIÙHDMI digital cable, the signal transmission
may not work property. (The HDMI specifi cation does not suppor t all connections to equipment that
has digital output terminal using a DVIÙHDMI digital cable.)
•
See page
with computer signals other than those listed may cause some of the functions to not work.
•
A Macintosh adaptor may be required for use with some Macintosh computers. Contact your nearest
Macintosh Dealer.
Depending on the computer you are using, an image may not be projected unless the
•
computer's external output port is switched on (e.g. Press “Fn” and “F5” keys
simultaneously when using a SHARP notebook computer). Refer to the specifi c instructions in
your computer's operation manual to enable your computer's external output port.
64 “Compatibility Chart” for a list of computer signals compatible with the projector. Use
HDMI cable (commercially available) HDMI
19
Connecting the Projector to Other Equipment (Continued)
Equipment
Video equipment
Camera/Video game
is only for PG-LX2000
Terminal on
connected equipment
HDMI output
terminal
Component
video output
terminal
Video output
terminal
Component
video
output
terminal
Video
output
terminal
HDMI cable (commercially available) HDMI
3 RCA to mini D-sub 15 pin cable
(optional, AN-C3CP2)
Video cable (commercially available) VIDEO
Cables for a camera or a vi deo game/3 RCA to
mini D-sub 15 pin cable (optional, AN-C3CP2)
Cables for a camera or a vi deo game
Cable
RCA adaptor plug
(commercially available)
Terminal o n the
projector
COMPUTER/
COMPONENT
COMPUTER/
COMPONENT
VIDEO
Note
Depending on specifi cations of equipment or the DVIÙHDMI digital cable, the signal transmission
•
may not work property. (The HDMI specifi cation does not suppor t all connections to equipment that
has digital output terminal using a DVIÙHDMI digital cable.)
HDMI (High-Defi nition Multimedia Interface) is a digital AV interface that can deliver a high-defi nition
•
video signal, multi-channel audio signal, and bi-directional control signal all in just one cable.
Because it is compatible with the HDCP (High-bandwidth Digital Content Protection) system, the
•
digital video signal does not degrade when transmitted, and a high-quality image with a simple
connection can be enjoyed.
The HDMI terminal does not support the CEC signal.
•
When you connect video equipment with a 21-pin RGB output (Euro-scar t) to the projector, use a
•
commercially available cable that fi ts in the projector terminal you want to connect.
The projector does not suppor t RGBC signals via the Euro-scart.
•
20
Equipment
Audio equipment
Terminal on
connected equipment
ø3.5 mm
audio output
terminal
ø3.5 mm stereo minijack to RCA audio cable
(commercially available)
Cable
Terminal o n the
projector
AUDIO
RCA audio
output
terminal
Audio
output
terminal
HDMI output
terminal
is only for PG-LX2000
Note
You can select HDMI or AUDIO in the INPUT list. (See page 27.)•
RCA audio cable (commercially available)
Cables for a camera or a vi deo game
HDMI cable (commercially available) HDMI
This projector is able to process the following signals when connected to HDMI
equipment:
•
Video signal: For details, see “Digital Support” in the list of “Compatibility Char t” on page 64.
•
Audio signal: Linear PCM audio
•
Sampling frequency: 48kHz/44.1kHz/32kHz
Connections
Connecting the Power Cord
Plug the supplied power cord into the AC
socket on the rear of the projector. Then
plug into AC outlet.
Power cord
Power cord
(supplied)
(supplied)
AC socket
AC socket
To A C out l et
To A C out l et
21
Loading...