Sharp PC900V0NSZX Datasheet
PREPARED
BY:
DATE:
SHAR
ELECTRONIC COMPONENTS
GROUP SHARP CORPORATION
SPECIFICATION
f DEVICE SPECIFICATION FOR
PHOTOCOUPLER
MODEL No.
I
(Businessdealingname: PC9OOVONSZXl
1. These specification sheets include materfals protected under copyright of Sharp Corporation (“Sharp”).
Please do not reproduce or cause anyone to reproduce them without Sharp’s consent.
2. When using this product, please observe the absolute maximum ratings and the instructions for use outlIned
in these specification sheets, as well as the precautions mentioned below. Sharp assumes no responsibility
for any damage resulting from use of the product which does not comply with the absolute maximum ratings
and the instructions included in these specification sheets, and the precautions menttoned below.
(Precautions)
(1) This product is designed for use in the following application areas ;
l
OA equipment
- Telecommunication equipment (Terminal)
* Tooling machines - Computers
i
If the use of the product in the above application areas is for equipment listed in paragraphs
(2) or (3). please be sure to observe the precautions gtven in those respective paragraphs.
* Audio visual equipment * Home appliances
PCSOOV
* Measuring equipment
I
1
-+=%An OPTO-ELECTRONIC DEVI
-
(2) Appropriate measures, such as fail-safe design and redundant design considering
the safety design of the overall system and equipment, should be taken to ensure reliability
and safety when this product is used for equipment which demands high reliability and
safety in function and precision, such as ;
* Transportation control and safety equipment (aircraft, train. automobile etc.)
- Traffic
* Other safety equipment
[
[3) Please do not use this product for equipment which require extremely high reliability
and safety in function and precision, such as :
* Space equipment * Telecommunication equipment (for trunk lines)
l
[
(4) Please contact and consult with a Sharp sales representative if there are any questions
regarding interpretation of the above three paragraphs.
3. Please contact and consult with a Sharp sales representative for any questions about this product.
CUSTOMER’S APPROVAL
DATE
BY
sigmk
Nuclear power control equipment * Medical equipment
* Gas leakage sensor breakers * Rescue and security equipment
DATE
PRESENTED J
BY
K. Hachimura,
Department General Manager of
Engineering Dept. .I1
Opto-Electronic Devices Div.
ELECOM Group
SHARP CORPORATION
I
1
F J-p. IJ, ,+a-3
/G&‘&&h
SHRRP CORPORATI
1. Application
This specification applies to the outline and characteristics of photocoupler
Model No. PCSOOV.
2. Outline
Refer to the attached sheet. page 3.
3. Ratings and characteristics
Refer to the attached sheet, page 3 to 5.
4. Reliability
Refer to the attached sheet, page 8.
ON
5. Outgoing inspection
Refer to the attached sheet. page 9.
6. Supplement
Isolation voltage shall be measured in the following method.
6.1
(I) Short among pins 1 to 3 on the primary side and among pins 4 to 6 on
the secondary side.
(2) The dielectric withstand tester with zero-cross circuit shall be used.
(3) The wave form of applied voltage shall be a sine wave.
(It is recommended that the isolation voltage be measured in insulation oil.)
6.2 The business dealing name used for this product when ordered or delivered shall be
PCSOOVONSZX.
6.3 Package specifications
Refer to the attached sheets-2- 1 to 2-3.
SHARP CORPORATION
6.4 UL : Under preparation
6.5 Theory of operation
(1) When the forward current of above the “H+L” threshold input current (Ir,.J
is applied to the input side, the output will go “Low level”.
(2) When the forward current on the input side goes below the “L+H” threshold
input current (I,,,) is applied to the input side, the output will go “High level”.
6.6 This product is not designed against irradiation.
This product is assembled with electrical input and output.
This product incorporates non-coherent light emitting,diode.
6.7 ODS materials
-
This product shall not contain the following materials.
Also, the following materials shall not be used in the production process for this product.
Materials for ODS : CFC, Halon, Carbon tetrachloride.
6.8 Brominated flame retardants
Specific brominated flame retardants such as the PBBOs and PBB, are not used
in this device at all.
7. Notes
Refer to the attached sheet-l- 1. 2.
1.1.1 -Trichloroethane (Methylchloroform)
SHARP CORPORATION
2. Outline
7.12zto.3
-
Anode inai
m
?I
m
cd
-
\ Lot No. ‘1
regulator
Pin
NOS.
Cathode N. c
Anode
connection diagram
l
7.629~0.3
and inter!‘Ial
l
2.54&O. 25
0.5fO. 1
*l) 2-digit number shall be marked according to
*2) Marking is laser marking
Product mass : Approx. 0.36g
DIN
standard.
Name
UNIT: l/l mm
PCSOOV
Outline Dimensions
(Business dealing
name : PC9OOVONSZX)
SHARP CORPORflTION
Ratings and characteristics
3.1 Absolute maximum ratings
*l The derating factors of absolute maximum ratings due to ambient temperature
are shown in Fig. 1, 2. 3.
*2 Pulse widths 100 ps, Dutyratio : 0.001
*3 AC for 1 min, 40 to 6O%RH
*4 ForlOs
Loading...