Sharp PC900V, PC900VY Datasheet

PREPARED BY: DATE:
SPEC. No. SA-88049D
SHARP ISSUE
March 25,
1996
PAGE
15 Pages
APPROVED BY: DATE:
REPRESENTATIVE DMSION
7 35h
/ .J-
niMj.;? Tf6
SPECIFICATION
OPTO-ELECTRONIC DEVICES DIV.
f
DEVICE SPECIFICATION FOR
PHOTOCOUPLER
MODEL No.
PCSOOV
Business dealing name
I
1. These specification sheets include materials protected under copyright of Sharp Corporation (“Sharp”). Please do not reproduce or cause anyone to reproduce them without Sharp’s consent.
2.
When using this product, please observe the absolute maximum ratings and the instructions for use outlined
in these specification sheets. as well as the precautions mentioned below. Sharp assumes no responsibility for any damage resulting from use of the product which does not comply with the absolute maximum ratings
and the instructions included in these specification sheets, and the precautions mentioned below.
(Precautions)
(1) This product is designed for use ln the following application areas :
[
* OA equipment * Audio visual equipment * Home appliances * Telecommunication equipment (Terminal) * Measuring equipment * Tooling machines . Computers
1
If the use of the product in the above application areas is for equipment listed in paragraphs (2) or (3). please be sure to observe the precautions given in those respective paragraphs.
(2) Appropriate measures, such as tbil-safe design and redundant design considering
the safety design of the overall system and equipment, should be taken to ensure reliability and safety when this product is used for equipment which demands high reliability and
safety in function and precision, such as ;
[
* Transportation control and safety equipment (aircraft, train, automobile etc.) * Traffic signals
* Gas leakage sensor breakers
. Rescue and security equipment
* Other safety equipment
1
(3) Please do not use this product for equipment which require extremely high reliability
and safety in function and precision, such as :
[
* Space equipment * Telecommunication equipment (for trunk lines) * Nuclear power control equipment . Medical equipment
1
(4) Please contact and consult with a Sharp sales representative lf there are any questions
regarding interpretation of the above three paragraphs.
3. Please contact and consult with a Sharp sales representative for any questions about this product.
CUSTOMER’S APPROVAL
DATE PRESENTED
BY
DATE
BY
T. Matsumura. Department General Manager of Engineering Dept.,11 Opto-Electronic Devices Div.
ELECOM
Group
SHARP CORPORATION
I
SHARP CORPORATION
SA-88049D 1 March25, 1996
MODEL No. PAGE
PCSOOV l/9
i
1. Application
This specification applies to the outline and characteristics of photocopier Model No. PCSOOV.
2. Outline Refer to the attached drawing No. CY544OKO2.
3. Ratings and characteristics Refer to the attached sheet, page 3 to 5.
4. Reliability
Refer to the attached sheet, page 8.
5. Incoming inspection
Refer to the attached sheet, page 9.
6. Supplement
6.1 Isolation voltage shall be measured in the following method. ( 1) Short among pins 1 to 3 on the primary side and among pins 4 to 6 on
the secondary side.
(2) The dielectric whhstand tester with zero-cross circuit shall be used.
(3) The wave form of applied voltage shall be a sine wave.
(It is recommended that the isolation voltage be measured in insulation oil.)
6.2 Business dealing name (”
0”
mark indicates business dealing name of ordered product)
Product
Business dealing name
Remarks
G
PCSOOV
PC9OOVY Applied to products as a option
(Attached sheets -2-l to 2-4.)
SHARP CORPORATION
6.3 This Model is approved by UL. Approved Model No. : PCSOOV UL file No. : E64380
6.4 Theory of operation
(1) When the forward current of above the “H-L” threshold input current (I,)
is applied to the input side, the output will go “Low level”.
(21 When the forward current on the input side goes below the “L-H” threshold
input current (I,1 the output will go “High level”.
6.5 This product is not designed against irradiation. This product is assembled with electrical input and output. This product incorporates non-coherent light emitting diode.
7. Notes Refer to the attached sheet-l-l, 2.
SHARP CORPORATION
PCSOOV
PCSOOV
SHARP
cc
Anode
3
Cathode
,z
N.C.
Voltage regulator
I
Pin Nos.
and internal
connection diagram
bode mark
\ Lot No. l l
Factory identification mark l 2
L
7.6210.3
* 1) a-digit number shall be marked according to DIN standard. *2) Factory identification mark shall be or shall not be marked.
UNIT: l/l mm
Name
Drawing No.
PCSOOV Outline Dimensions (Business dealing name : PC9OOW
CY5440K02
SHARP CORPORATION
SA-88049D 1 March25. 1996
MODEL No. PAGE
PCSOOV
4/9
3. Ratings and characteristics
3.1 Absolute maximum ratings Ta=25C
Parameter
I
*l Forward current
P
~~ I
70
unit
mA
A V
mW
Supply voltage vcc 16
V
High level output voltage
VOH
16 V
output
Low level output current
r,
50 m.A *l Power dissipation PO 150 mW * 1 Total power dissipation
I
Ptot
I
170
I
mW
*3 Isolation voltage viso
Operating temperature
Topr
*4 Storage temperature
Tstg
5.0
-25 to +85
-40 to 125
kVrms
‘C “C
*4 Soldering temperature
I
Tsol
I
260
I
‘C
*l The derating factors of absolute maximum ratings due to ambient temperature
areshowninFig. 1, 2, 3.
*2 Pulse widths 100 /1 s, Dutyratio :
0.001 l 3 AC for 1 min. 40 to 6O%RH *4 For 10s
Loading...
+ 11 hidden pages