Sharp MX-M264U, MX-M264N, MX-M264NV, MX-M264NR, MX-M314U Installation Manual

...
Page 1
Parts marked with " " are important for maintaining the safety of the set. Be sure to replace these parts with specified ones for maintaining the safety and performance of the set.
This document has been published to be used for after sales service only. The contents are subject to change without notice.
SHARP CORPORATION
INSTALLATION MANUAL
MX-M264U/M264N/ M264NV/M264NR MX-M314U/M314N/ M314NV/M314NR MX-M354U/M354N/354NR
MODEL
Page 2
MX-M264U Transit, Installation (using) environment, Note - i
MX-M264U
5GTXKEG/CPWCN
Transit, Installation (using) environment, Note
* About a main unit illustration, it may differ from a target model.
1. Installing (use) conditions
Before installing the machine, check that the following installing (use) conditions are satisfied.
If the installing (use) conditions are not satisfied, the machine may not display full performances, resulting in troubles. It may also cause safety problems. Therefore, be sure to arrange the installing (use) conditions before setting up the machine.
A. Transportation space
For installation of a large size machine, be sure to check that the door size is wide enough before bringing in.
B. Installing space
The following space must be provided around the machine in order to assure machine performances and proper operations.
If any option is installed, provide the additional space for installing it.
Adequate space must be provide behind the machine for proper ventilation heat and dust. If not, the machine cannot exhibit func­tions against heat and dust, causing some troubles.
C. Power source (Capacity, voltage, frequency,
safety, plug)
If the power specifications are not satisfied, the machine cannot exhibit full performances and may cause safety trouble.
Strictly observe the following specifications.
(1) Power capacity
Check that the following power capacity is satisfied. If not, addition­ally provide a power source.
Current capacity
Japan: 20A or more
EX 100V: 15A or more
EX 200V: 10A or more
NOTE: Check the shape of the power plug of the machine, and
insert it into a power outlet of the acceptable shape.
(2) Power voltage
Measure the voltage during copying to check that the voltage is in the range of the specified voltage r10%.
If the voltage is outside the specified range, please have a certified electrician upgrade the outlet.
(An electrical work is required.)
Use of a step-up transformer is also available. In this case, the capacity must be great enough for the max. power consumption of the machine.
(3) Power frequency, waveform
The frequency must be within the range of the specified frequency r2%. If power waveform is deformed, a trouble may occur.
(4) Safety
Be sure to properly ground the machine.
Grounding (earth connection) must be performed before inserting the power plug into the power outlet.
When disconnecting the earth connection, be sure to disconnect the power plug from the power outlet in advance.
(5) Power plug
Check the shape of the power plug of the machine, and insert it into a power outlet of the acceptable shape. Power plug stated in power capacity.
D. Floor strength and level
This machine is considerably heavy and becomes heavier with an option installed.
The floor must be strong enough to safely support the weight of the machine as well as any installed options.
If the unit is not horizontally installed, the toner density control is not performed normally, degrading the copy quality.
If not, color shift or image distortion may occur. To assure proper Image quality, make sure the machine is setting level.
E. Direct rays of the sun, dust, temperature,
humidity, gasses, chemicals, vibration
(1) Temperature and humidity (Environmental
conditions)
This machine is designed to perform properly under the specified temperature and humidity. If the temperature and humidity exceeds the specified range, the machine may not operate properly and or cause equipment failure.
Especially when the humidity is too high, paper absorbs humidity to cause a paper jam or dirty copy.
Do not install the machine near a heater, a cooler, or a humidifier.
Condensation may form inside the machine causing multiple trou­bles. Use enough care for ventilation.
No. Content
1 Transportation space 2 Installing space 3 Power source (Capacity, fluctuation, safety) 4 Floor strength 5 Direct rays of the sun, dust, temperature, humidity, gases,
chemicals
11-13/16" (30cm)
11-13/16" (30cm)
17-23/32" (45cm)
Page 3
MX-M264U Transit, Installation (using) environment, Note - ii
Operational environment
Temperature: 10 to 35qC
Humidity: 20 to 85% RH
Atmospheric pressure: 590 to 1013hPa (altitude: 0 to 2000 m)
(2) Contaminates
If dust enters the machine, it may cause dirty copy and a paper jam, resulting in a shortened lifetime.
(3) Direct sunlight
If the machine is installed under the rays of the sun, the exterior of the machine may be discolored and abnormal copies may be pro­duced.
(4) Gases and chemicals
Do not install the machine at a place where there are gases and chemicals. Especially be careful to avoid installation near a diazo­type copier, which produces ammonium gas.
Copy quality may be adversely affected and a trouble may be caused.
(5) Vibration
Avoid installation near a machine which produces vibrations.
If vibrations are applied to the copier machine, copy images may be deflected and a trouble may be caused.
F. Note for handling PWB and electronic parts
When handling the PWB and the electronic parts, be sure to observe the following precautions in order to prevent against dam­age by static electricity.
• When in transit or storing, put the parts in an anti-static bag or an anti-static case and do not touch them with bare hands.
• When and after removing the parts from an anti-static bag (case), use an earth band as shown below:
• Put an earth band to your arm, and connect it to the machine.
• When repairing or replacing an electronic part, perform the
procedure on an anti-static mat.
85%
HumidityRH
60%
20%
(50F)
(86F)
(95F)
Page 4
MX-M264U Transit, Installation (using) environment, Note - iii
G. Note for proper drum, developing and fusing
unit handling
When handling the OPC drum and developing units, observe the following items.
Drum unit
• To prevent damage to the OPC drum, avoid working on the drum unit in high intensity light areas.
• When the OPC drum is removed from the machine, cover it with light blocking material. (When using paper, use about 10 sheets of paper to cover it.)
• Be careful not to attach fingerprints, oil, grease, or other foreign material on the OPC drum surface.
Developing unit
• Be careful not to "leave” fingerprints, oil, grease, or other foreign material on the developing unit.
Fusing unit
• Be careful not to "leave” fingerprints, oil, grease, or other foreign material on the fusing roller.
If these items are neglected, a trouble may be generated in the copy and print image quality.
2. Transit and delivery
A. Implements, facility, and manpower
It is recommendable to use a forklift for bringing in the machine for safety.
If no forklift is available, man-power of two persons is required. The machine is considerably heavy, and requires safety precautions for delivery and installation.
Transit of the machine must be made in packed condition to the installing place.
Use care not to exert vibrations or shocks to the machine when in transit.
B. Delivery
Remove the packing materials prior to installation in the office envi­ronment.
No. Content Method
1 Implements, facility,
and man power
Use a forklift. (If no forklift is available, manpower of two persons is required.)
2 Delivery Transit must be made in packed condition.
Page 5
MX-M264U MX-M264U/M314U/M354U/M264N/M314N/M354N/M264NV/M314NV/M264NR/M314NR/M354NR (MAIN UNIT) 2 – 1
MX-M264U
6HUYLFH0DQXDO
[2] MX-M264U/M314U/M354U/M264N/M314N/M354N/M264NV/M314NV/
M264NR/M314NR/M354NR (MAIN UNIT)
1. Unpacking
A. Unpacking
B. Fixing tape and protection material removal
C. Packed items check
D. Lock release
(1) Tray rotation plate lock release
1) Pull out the tray. Turn the fixing material and remove it. Remove the caution label. Attach the removed fixing material to the position shown in the figure for future use. Close the tray which was pulled out.
(2) Scanner (2/3 mirror unit) lock release
1) Remove the optical unit fixing screw, and remove the note label.
No. Name Quantity
1 Operation manual 1
1
Page 6
MX-M264U MX-M264U/M314U/M354U/M264N/M314N/M354N/M264NV/M314NV/M264NR/M314NR/M354NR (MAIN UNIT) 2 – 2
2. Installation
NOTE: When an optional paper feed desk is connected to the
machine, unpack and install the paper feed desk, then unpack the machine. Place the machine on the option desk securely, and perform the installing procedures of the machine. Place the machine on the optional desk firmly and secure.
A. Developer installation
NOTE: Be careful not to leave fingerprints or oily dirt on the DV
roller surface.
1) Hold the both sides of the front cover, and pull down to open it.
2) Loosen the blue screw and pull out the developing unit.
3) Remove the cover from the developer unit.
4) Rotate the MG roller in the arrow direction and supply devel­oper evenly into the developing unit.
NOTE: Shake the developer bag well before opening it.
NOTE: Check that the DV seal is free from developer. If devel-
oper is attached to the DV seal, clean and remove it.
NOTE: After supplying developer into the developer unit, do
not tilt or shake the developer unit.
5) Attach the developer unit to the copier, and fix it with the screw.
B. Set the control level for the reference toner
density
1) With the front cabinet open, connect the power plug to the power outlet.
2) Shake the toner cartridge horizontally 20 times.
3) Insert the toner cartridge.
NOTE: Do not forcibly insert the toner cartridge.
Push it in until the cartridge is securely locked in place.
4) Turn ON the main power switch of the machine and the power switch on the operation panel.
5) Enter the SIM25-2 mode.
6) Close the front cabinet.
7) Press [EXECUTE] key.
8) After completion of the adjustment, press reset key of the machine to exit the simulation mode.
C. Paper feed tray setup
(1) System setting
1) Press the [SYSTEM SETTINGS] key.
2) Touch the [Paper Tray Settings] key.
3) Touch the [Paper Tray Settings] key to configure the settings. These settings specify the paper type, paper size, and func­tions allowed for each paper tray. When the [Tray Settings] key is touched, a list appears showing the trays and the current settings.
4) Touch the [Change] key in the above screen to change the set­tings. The following settings can be configured.
Item Description
Type Select the type of paper that is loaded in the tray.
The paper types that can be selected vary by paper tray.
Size Select the paper size from the list. The paper sizes
that can be selected vary by tray. The sizes that can be selected may also be restricted by the paper type selected above. If the desired size does not appear in the list, select [Custom Size] and directly enter the size (only for
the bypass tray). Feeding Approved Job
Select the modes that can be used. If there is a
function that you do not wish to be used with the
selected tray, disable the function. When the "Type"
is other than plain paper, recycled paper, colored
paper, or a user type, [Fax] and [Internet Fax]
cannot be selected.
Page 7
MX-M264U MX-M264U/M314U/M354U/M264N/M314N/M354N/M264NV/M314NV/M264NR/M314NR/M354NR (MAIN UNIT) 2 – 3
(2) Tray size setup
1) Pull out the paper tray.
Gently pull the tray out until it stops.
If paper remains in the tray, remove it.
2) Adjust the guide plates A and B by squeezing their lock levers and sliding them to match the vertical and horizontal dimen­sions of the paper to be loaded.
The guide plates A and B are slidable. Slide each guide plate while squeezing its lock lever.
A
B
Loading...