Sharp MD-MT20WS, MD-MT20WGL, MD-MT20WBL, MD-MT20CS, MD-MT20S Service Manual

MD-MT20/20C/20W
SERVICE MANUAL
No. S6943MDMT20//
MD-MT20(S) MD-MT20C(S) MD-MT20W(BL) MD-MT20W(GL)
Illustration: MD-MT20/20C
MD-MT20W(S)
• In the interests of user-safety the set should be restored to its original condition and only parts identical to those specified be used.
Illustration: MD-MT20W
CONTENTS
SAFETY PRECAUTION FOR SERVICE MANUAL (MD-MT20W ONLY).............................................................................. 2
SPECIFICATIONS ................................................................................................................................................................. 3
NAMES OF PARTS ............................................................................................................................................................... 4
OPERATION MANUAL .......................................................................................................................................................... 5
QUICK GUIDE (MD-MT20 ONLY) ......................................................................................................................................... 8
DISASSEMBLY.................................................................................................................................................................... 10
REMOVING AND REINSTALLING THE MAIN PARTS....................................................................................................... 11
ADJUSTMENT ...................................................................................................................................................................... 12
NOTES ON SCHEMATIC DIAGRAM .................................................................................................................................. 25
TYPES OF TRANSISTOR AND DIODE .............................................................................................................................. 25
VOLTAGE ............................................................................................................................................................................ 26
BLOCK DIAGRAM ............................................................................................................................................................... 27
SCHEMATIC DIAGRAM ...................................................................................................................................................... 28
WIRING SIDE OF P.W.BOARD........................................................................................................................................... 31
WAVEFORMS OF MD CIRCUIT ......................................................................................................................................... 36
TROUBLE SHOOTING ........................................................................................................................................................ 37
FUNCTION TABLE OF IC.................................................................................................................................................... 40
CIRCUIT DESCRIPTION ..................................................................................................................................................... 42
Page
SHARP CORPORATION
– 1 –
This document has been published to be used for after sales service only. The contents are subject to change without notice.
MD-MT20/20C/20W
SAFETY PRECAUTION FOR SERVICE MANUAL (MD-MT20W ONLY)
Precaution to be taken when replacing and servicing the Laser Pickup.
The AEL (Accessible Emission Level) of Laser Power Output for this model is specified to be lower than Class I Requirements. However, the following precautions must be observed during servicing to protect your eyes against exposure to the laser beam.
(1) When the cabinet has been removed, the power is turned on without a compact disc, and the Pickup is on a position
outer than the lead-in position, the Laser will light for several seconds to detect a disc. Do not look into the Pickup Lens.
(2) The Laser Power Output of the Pickup inside the unit and replacement service parts have already been adjusted prior
to shipping. (3) No adjustment to the Laser Power should be attempted when replacing or servicing the Pickup. (4) Under no circumstances look directly into the Pickup Lens at any time. (5) CAUTION - Use of controls or adjustments, or performance of procedures other than those specified herein may result
in hazardous radiation exposure.
CAUTION
This Portable MiniDisc Recorder is classified as a CLASS 1 LASER product. The CLASS 1 LASER PRODUCT label is located on the bottom. Use the Portable MiniDisc Recorder only in accordance with the instructions given in this manual and do not attempt to interfere with the interlock switch or make any other adjustment as this may result in exposure to hazardous radiation.
Laser Diode Properties
Material: GaAIAs Wavelength: 785 nm Pulse time: Read mode; 0.8 mW Continuous Write mode; max. 10 mW 0.5S
min. cycle 1.5S
Repetition
VARO ! Avattaessa ja suojalukitus ohitettaessa olet alttiina näkymättömälle lasersäteilylle. Älä katso säteeseen. VARNING! Osynlig laserstralning när denna del är öppnad och spärren är urkopplad. Betrakta ej strälen.
Precaution to be taken when replacing and servicing the laser pickup. The following precautions must be observed during servicing to protect your eyes against exposure to the laser.
Warning of possible eye damage when repairing: If the AC adaptor or batteries are connected when the top houising (disc cover) of the unit is removed, and the PLAY key is pressed, the laser will light up during focus access (2-3 seconds). (Fig. 2-1) During the operation, the laser will leak from the opening between the magnetic head and the mechanical chassis (Fig. 2-2). In order to protect your eyes, you must not look at the laser during repair. Before repairing be sure to disconnect the AC adaptor and remove the batteries.
Magnet head
Optical pick-up
Top Cabinet
Mechanism Chassis
Spindle motor
Magnet Head
Main PWB
Laser Beam
Optical Pick-Up
Figure 2-1 Figure 2-2
– 2 –
FOR A COMPLETE DESCRIPTION OF THE OPERATION OF THIS UNIT, PLEASE REFER TO THE OPERATION MANUAL.
SPECIFICATIONS
MD-MT20/20C MD-MT20W
General
Power source:
Power consumption: Output power:
Charging time:
Battery life:
DC 2.4V: Rechargeable Nickel-Metal Hydride battery (AD­DC 5V: AC adaptor (AC 120V, 60 Hz)
DC 3.0V: Commercially available, “AA” size (LR6), alkaline DC 4.5V: Separately available car adaptor, AD-CA20X
7.5W(AC adaptor) RMS; 20 mW (10 mW + 10 mW)
(0.2% T.H.D.) Approx. 4 hours (90 %)
Approx. 6 hours (fully charged) (When using the AC adaptor included with the unit)
T20BT) x 1
battery x 2 (for cars with a 12-24V DC negative ground elec-
trical system)
When using the rechargeable battery (fully charged) included with the unit
Continuous recording:
Approx. 7.5 hours
Continuous play: Approx. 12 hours
When using two, commercially available, high capacity, “AA” size (LR6), alkaline batteries
Continuous recording:
Approx. 7.5 hours
Continuous play: Approx. 15 hours
General
Power source:
Power consumption: Output power:
Charging time:
Battery life:
MD-MT20/20C/20W
DC 2.4V: Rechargeable Nickel-Metal Hydride battery (AD­DC 5V: AC adaptor (AC 110 - 240V, 50/60 Hz)
DC 3.0V: Commercially available, “AA” size (LR6), alkaline DC 4.5V: Separately available car adaptor, AD-CA20X
0.15A (AC adaptor) RMS; 20 mW (10 mW + 10 mW)
(0.2% T.H.D.) Approx. 4 hours (90 %)
Approx. 6 hours (fully charged) (When using the AC adaptor included with the unit)
T20BT) x 1
battery x 2 (for cars with a 12-24V DC negative earth electri-
cal system)
When using the rechargeable battery (fully charged) included with the unit
Continuous recording:
Approx. 7.5 hours
Continuous play: Approx. 12 hours
When using two, commercially available, high capacity, “AA” size (LR6), alkaline batteries
Continuous recording:
Approx. 7.5 hours
Continuous play:
Approx. 15 hours
The continuous recording time is for analog inputs when the volume level is set to “VOL 0”.
The continuous play time shows the value when the volume level is set to “VOL 15”.
The above values are the standard values when the unit is charged and used at an
ambient temperature of 68°F (20°C).
The operating time when using an alkaline battery may be different, depending on the type and manufacturer of the battery, and on the operating temperature.
Input sensitivity:
Output level:
Dimensions: Width: 3-7/16"(87.9 mm)
Weight: 0.52 lbs. (235 g) with rechargeable battery Input jack: Line/optical digital, microphone (powered by the main unit) Output jack: Headphones (impedance: 19 ohms)/remote control unit
Recording level Reference input level Input impedance
MIC H 0.25 mV 10 k ohms MIC L
LINE 100 mV 20 k ohms
Headphones 10 mW + 10 mW 16 ohms
LINE
Height: 1-3/16" (29.8 mm) Depth: 3-1/8" (79.7 mm)
2.5 mV 10 k ohms
Specified
output
250 mV (-12dB)
Maximum
output level
Load
impedance
10 k ohms
MiniDisc Recorder
Type: Portable MiniDisc recorder Signal readout: Non-contact, 3-beam semi-conductor laser pick-up Audio channels: Stereo 2 channels/monaural (long-play mode) 1 channel Frequency response: Rotation speed: Approx. 400 – 900 rpm Error correction: ACIRC (Advanced Cross Interleave Reed-Solomon Code) Coding: ATRAC (Adaptive Transform Acoustic Coding), 24-bit com-
Recording method: Magnetic modulation overwrite method Sampling frequency:
Wow and flutter:
20 – 20,000 Hz (± 3 dB)
puted type
44.1 kHz (32 kHz and 48 kHz signals are converted to 44.1 kHz, and then recorded.)
Unmeasurable (less than ±0.001% W. peak)
The continuous recording time is for analogue inputs when the volume level is set to
“VOL 0”. The continuous play time shows the value when the volume level is set to “VOL 15”. The above values are the standard values when the unit is charged and used at an
ambient temperature of 20°C (68°F). The operating time when using an alkaline batteries may be different, depending on
the type and manufacturer of the battery, and on the operating temperature.
Input sensitivity:
Output level:
Dimensions: Width: 87.9 mm (3-7/16")
Weight: 235 g (0.52 lbs.) with rechargeable battery Input socket: Line/optical digital, microphone (powered by the main unit) Output socket: Earphones (impedance: 32 ohms)/remote control unit
Recording level Reference input level Input impedance
MIC H 0.25 mV 10 k ohms
MIC L
LINE 100 mV 20 k ohms
Earphones 10 mW + 10 mW 32 ohms
LINE
Height: 29.8 mm (1-3/16") Depth: 79.7 mm (3-1/8")
2.5 mV 10 k ohms
Specified
output
250 mV (-12dB)
Maximum
output level
Load
impedance
10 k ohms
MiniDisc Recorder
Type: Portable MiniDisc recorder Signal readout: Non-contact, 3-beam semi-conductor laser pick-up Audio channels: Stereo 2 channels/monaural (long-play mode) 1 channel Frequency response: Rotation speed: Approx. 400 – 900 rpm Error correction: ACIRC (Advanced Cross Interleave Reed-Solomon Code) Coding: ATRAC (Adaptive Transform Acoustic Coding), 24-bit com-
Recording method: Magnetic modulation overwrite method Sampling frequency:
Wow and flutter:
20 – 20,000 Hz (± 3 dB)
puted type
44.1 kHz (32 kHz and 48 kHz signals are converted to 44.1 kHz, and then recorded.)
Unmeasurable (less than ±0.001% W. peak)
Specifications for this model are subject to change without prior notice
– 3 –
MD-MT20/20C/20W
Main unit
1. Monaural Long-Play Mode Indicator
2. Record Indicator
3. Level Meter
4. Fast Play Indicator
5. Repeat Indicator
6. TOC Indicator
7. Battery Indicator
8. Random Indicator
9. Track Number Indicator
10. Character/Time Information Indicator
11. Synchro Recording Indicator
12. Disc Mode Indicator
13. Disc Name Indicator
14. Track Name Indicator
15. Remaining Recording Time Indicator
16. Total Track Number Indicator
17. Edit/Auto Mark/Time Mark Button
18. Mode Button
19. Display/Character Select Button
20. Bass/Delete Button
21. Enter/Fast Play/Synchro Button
22. Volume Up/Cursor Button
23. Volume Down/Cursor/Charge Button
24. Record/Track Mark Button
25. Fast Reverse/Recording Level Down/ Name Select Button
26. Stop/Power Off Button
27. Play/Pause Button
28. Fast Forward/Recording Level Up/ Name Select Button
NAMES OF PARTS
Illustration: MD-MT20/20C
11 12
13 14
17
29
123456
15 16
18 20 21
19
28
27262524
7 8
9 10
22 23
30 31
29. Open Lever
30. Remote Control/Earphones Socket
31. Optical/Line Input Socket
32. Microphone Input Socket
33. Hold Switch
34. 5V DC Input Socket
35. Battery Cover
Remote control unit
1. Headphones Jack (MD-MT20/20C)
1. Earphones Socket (MD-MT20W)
2. Fast Reverse/Recording Level Down/ Name Select Button
3. Hold Switch
4. Play/Pause Button
5. Fast Forward/Recording Level Up/ Name Select Button
6. Stop/Power Off Button
7. Volume Up/Cursor Button
8. Bass/Delete/Track Mark Button
9. Volume Down/Cursor Button
1
2
3
32
33
34 35
4 5
6 7
8 9
– 4 –
OPERATION MANUAL
POWER SOURCE
This unit can be used with the following power sources: a rechargeable battery, an AC
adaptor, commercially available alkaline batteries, and a separately available car adaptor
(AD-CA20X).
Rechargeable battery power
When the rechargeable battery is used for the
first time or when you want to use it after a
long period of disuse, be sure to charge it fully.
1
Open the battery cover.
Slide the battery cover as far as it will
go to the outside and then lift to open it.
If the battery cover is lifted without be-
ing slid all the way out, it may break.
2
Insert the rechargeable battery accord-
ing to the polarity marked on the bottom
of the unit.
3
Close the battery cover.
4
Plug the AC adaptor into the AC socket,
and then insert the plug on the AC adap-
tor lead into the DC IN 5V socket.
5
Press the CHARGE (VOLUME down)
button of the main unit to begin charg-
ing.
” will appear, and the battery
will begin charging.
After about 4 hours have passed,
” will go out.
This indicates that the battery charg-
ing is about 90% compleate.
To charge the battery fully, continue
charging for about 2 more hours.
(In this case, you do not need to press
the CHARGE button. Even if the
CHARGE button is pressed, “
will not appear.)
Notes:
After charging has been completed, the
AC adaptor may be left connected.
(For example, when charging at night)
The battery will not be charged when the
power to the main unit is turned on.
Do not force open the battery cover too wide.
Do not use a rechargeable battery or an
AC adaptor other than those specified
(ACCESSORIES).
The charging time will vary, depending
on the condition of the battery.
When the battery is charged for the first
time or is charged after not being used
for a long period, the operating time may
be shorter than normal.The battery life
will recover with normal use i.e. charg-
ing and discharging.
T o avoid shortening the service life of the
battery only recharge the battery after it
has been completely discharged.
1
2
3
5
4
AC 110-240V,
50/60 Hz
Insert securely,
all the way in.
To the DC IN 5V socket
AC 120V,
60 Hz
Insert securely,
all the way in.
To the DC IN 5V jack
For MD-MT20/20C
For MD-MT20W
RECORDING USING THE OPTICAL DIGITAL CABLE
This is the method used for recording digi-
tal signals from CDs or MDs exactly as they
are stored on the original. Compared to re-
cordings made from analogue inputs, digi-
tal recordings have extremely high-quality
sound.
1
Connect the external equipment.
2
Start recording.
Synchro recording:
Before starting a synchro recording,
perform the following steps on the
equipment connected to this unit.
(1) First, put it in the playback mode.
(2) Next, put it in the pause mode.
(3) Finally, position it at the beginning
of the track you want to record.
(1) Insert a recordable MiniDisc, and
then press the REC button.
(2) Press the ENTER/SYNC button.
(3) Start the playback on the equipment
connected to this unit.
Manual recording:
(1) Insert a recordable MiniDisc, and
then press the REC button.
(2) Press the button.
When recording from digital inputs,it
is not necessary to adjust the record-
ing level.
Notes:
This unit incorporates a sampling rate
converter.
When this unit is connected to digital
equipment such as CS/BS tuners or DA T
tape recorders that use a different sam-
pling frequency (32 kHz or 48 kHz), re-
cordings can still be made. (The sam-
pling frequency of this unit is 44.1 kHz.)
When making a digital recording from a
portable CD player (if the player has a
sound skip prevention function and this
function is turned on) the optical output
will drop out and digital recording will not
be possible. Be sure to turn the sound
skip prevention function off.
There are cases where digital recording
may be impossible.
In the following cases digital recording is
impossible, even if you are using digital
cables.
When you attempt to make a new digital
recording from a track that was digitally re-
corded on a MiniDisc.
MiniDiscs are designed so that only first
generation digital copies can be made.
Further digital copies are prevented by
the SCMS (Serial Copy Management
System).
Playback
Digital cable
CD player, MD
player, etc.
Digitally recorded MiniDisc
Analogue recording is
possible.
Recording
Playback
Digital cable
Recording
MD player
MD-MT20/20C/20W
– 5 –
MD-MT20/20C/20W
If the hold function is active whilst the power
is turned off, the power cannot be turned
on by mistake and the battery will not be
accidentally drained.
CONVENIENT OPERATION OF THE UNIT
< How to read the battery indicator >
When the battery is completely discharged,
the battery indicator will flash. Recharge the
battery or replace the alkaline batteries with
a new one.
When the battery has run completely out,
“BATT EMPTY” will appear. Then, the
power will be disconnected automatically.
Notes:
When using the unit with alkaline batteries
or a rechargeable battery, the battery indi-
cator will not correctly display the remain-
ing capacity for approximately 10 seconds
after the power has been turned on.
When the AC adaptor included with this unit
or a separately available car adaptor is
used, the battery indicator will not be shown.
The number of bars shown in the battery
indicator may increase or decrease, de-
pending on the operation being performed.
This is normal.
To prevent the unit from being
operated by mistake
To avoid accidental operation of the unit,
use the hold function.
Move the HOLD switch to the safety posi-
tion (direction indicated by the arrow).
When the unit is in the hold mode, press-
ing the buttons will have no affect.
To cancel the hold mode, move the
HOLD switch away from the safety po-
sition (the opposite direction of the ar-
row).
Battery indicator
Since the battery level is very low, you
cannot start recording or editing.
When the battery
level is high
When the battery
level is very low
Remote
control unit
Main
unit
Can be operated
from either the
remote control unit or
the main unit.
Can only be operated
from the remote
control unit.
Can only be operated
from the main unit.
Cannot be operated
from either the
remote control unit or
the main unit.
Cancel
Cancel
Cancel
Cancel
Hold
Hold
Hold
Hold
Checking the remaining amount
of battery level
The remaining amount of battery level is
shown by the battery indicator (
) dur-
ing operation.
TROUBLESHOOTING
Moisture condensation
In the following cases, condensation
may form inside the unit.
Shortly after turning on a heater.
When the unit is placed in a room where
there is excessive steam or moisture.
When the unit is moved from a cool
place to a warm place.
When the unit has condensation inside,
the disc signals cannot be read, and the
unit may not function properly.
If this happens, remove the disc.
The condensation should evaporate in
approximately 1 hour. The unit will then
function properly.
Many potential “problems” can be resolved by the owner without calling a service techni-
cian.
If something seems to be wrong with this product, check the following before calling your
authorised SHARP dealer or service centre.
PROBLEM CAUSE
The unit does not turn
on.
Is the AC adaptor disconnected?
Is the battery exhausted?
Is the unit in the hold mode?
Has condensation formed inside the unit?
Is the unit being influenced by mechanical shock or by
static electricity?
Is the volume set too low?
Is the remote control unit or the earphones plugged in?
Are you trying to play a MiniDisc with data on it instead
of a MiniDisc containing music?
Is the unit in the hold mode?
Is the battery exhausted?
Is the remote control unit plug or the earphone plug in-
serted firmly?
Is the battery exhausted?
Is the unit being subjected to excessive vibration?
Has the track number or character information been
written on the disc yet?
Is the unit in the recording or editing mode?
Is the MiniDisc protected against accidental erasure?
Is the unit connected properly to the other equipment?
Is the AC adaptor unplugged or did a power failure oc-
cur whilst recording or editing?
Is the unit in the hold mode?
Is an optical signal being output from the external equip-
ment?
Read the operation manual for the external equipment.
No sound is heard from
the earphones.
When the operation
buttons are pressed, the
unit does not respond.
Some sounds are
skipped.
The MiniDisc cannot be
ejected.
Recording and editing
are impossible.
If trouble occurs
When this product is subjected to strong
external interference (mechanical shock,
excessive static electricity, abnormal sup-
ply voltage due to lightning, etc.) or if it is
operated incorrectly, it may malfunction.
If such a problem occurs, do the following:
1. Unplug the AC adaptor from the AC
socket.
2. Remove the battery.
3. Leave the unit completely unpowered for
approximately 30 seconds.
4. Plug the AC adaptor back into the AC
socket and retry the operation.
If strange sounds, smell or smoke come out
of the unit or an object is dropped into the
unit, remove the AC adaptor from the AC
socket immediately and contact an
authorised SHARP service centre.
– 6 –
MD-MT20/20C/20W
When the number of tracks used reaches
the limit, regardless of the remaining re-
cording time, further recording will be
impossible.
(Maximum number of tracks: 255)
If a MiniDisc has been recorded or ed-
ited repeatedly or if a MiniDisc has
scratches on it, it may not be possible to
record the maximum number of tracks on
it.
If there are scratches on a disc, the unit
will automatically avoid recording in those
areas. The recording time will be reduced.
When the remaining recording time of a
disc is displayed, short tracks less than
12 seconds long may not be included in
the total.
For MiniDiscs on which repeated record-
ing and editing operations were per-
formed, the COMBINE function may not
work.
A cluster (about 2 seconds) is normally the
minimum unit of recording. So, even if a track
is less than 2 seconds long, it will use about
2 seconds of space on the disc.
Therefore, the time actually available for re-
cording may be less than the remaining time
displayed.
If there are scratches on discs, those sec-
tions will be automatically avoided (no record-
ing will be placed in those sections). There-
fore, the recording time will be reduced.
For MiniDiscs on which repeated record-
ing and editing were performed, some
sounds may be skipped whilst cueing and
reviewing.
If there are scratches or dust on a
MiniDisc, the track numbers following that
track will be increased by one.
MINIDISC SYSTEM LIMITATIONS
MiniDiscs are recorded using a different system than is used for cassette tapes or DAT
recordings. Therefore, the following conditions may be encountered, depending on how
the disc has been recorded or edited. These are due to system limitations, and should be
considered normal.
Even if the maximum recording
time of a MiniDisc has not been
reached, “DISC FULL” or “TOC
FULL” may be displayed.
Even if the number of tracks and
the recording time have not
reached the limit, “DISC FULL”
may be displayed.
Even if several short tracks are
erased, the remaining recording
time may not show an increase.
Two tracks may not be combined
in editing.
The total of the recorded time and
time remaining on a disc may not
add up to the maximum possible
recording time.
When recorded tracks are played
back using the cue and review op-
erations, some sounds may be
skipped.
A track number can be created in
the middle of a track.
The battery is run down.
Nothing is recorded.
No copy can be made because of the
SCMS copyright system.
A track cannot be edited.
Recording cannot be performed
correctly due to vibration or shock in
the unit.
Editing is impossible.
The disc is scratched.
Poor connection of the digital cable.
The disc is out of recording space.
The unit is in the hold mode.
The EJECT lever was moved during
recording or editing.
A disc has not been loaded.
You tried to record on a playback- only
disc.
Improper power is being supplied.
The MD is write protected.
You tried to record without loading an
MD.
A playback-only MD was loaded and
the REC button was pressed when the
power was off.
The disc is damaged.
Since a track number is currently being
located or written to, the unit cannot
accept your command.
You have come to the conclusion that
the unit is out of order.
The temperature is too high.
A large portion of the disc has been
damaged.
There is no space left for recording
character information (track names,
disc names, etc.).
The track has been protected from
being erased.
A large portion of the disc has been
damaged.
There is an error in the recorded signal.
A disc which contains data other than
music was played.
There is an error in the signal from the
disc.
Charge the rechargeable battery or
replace the alkaline battery (or use the
AC adaptor for power).
Replace the disc with a recorded disc.
Record using the analog cable.
Change the stop position of the track
and then try editing it.
Re-record or replace it with another
recordable disc.
Check the number of tracks.
If the sound you hear is not right, try
recording again.
Replace the disc with another
recordable disc.
Connect the digital cable securely.
Replace it with another recordable disc.
Return the HOLD switch to its original
position.
Turn off the power and remove the
MiniDisc.
Load a disc.
Replace it with a recordable disc.
Use one of the specified power
sources.
Move the write protection knob back to
its original position.
Load a recordable MD.
Replace it with a recordable MD.
Reload the disc or replace it.
Replace it with another recorded disc.
Wait for a while and try the operation
again.
To have it repaired, go to the distributor
where you purchased the unit.
Turn off the power, and wait for a while.
Replace it with another recorded disc.
Replace it with another recordable disc.
Edit the track with the device on which
it was recorded.
Replace it with another recorded disc.
Erase all of the signal errors, and then
try recording again.
A disc which contains non-music data
cannot be played.
Replace it with another recorded disc.
ERROR MESSAGES
( ): Error messages seen on the remote control.
Error messages
Remedy
BATT EMPTY
(Lo BATT)
BLANK DISC
(BLANK)
Can’t COPY
(Not REC)
Can’t EDIT
Can’t REC
(Not REC)
Can’t WRITE
DEFECT
(DEFECT)
Din UNLOCK
(UNLOCK)
READ ERROR
(E-READ)
DISC FULL
HOLD
(HOLD)
LOCKED
LOCK ERROR
NO DISC
PB DISC
POWER ?
SORRY
(SORRY)
SYSTEM ERR
(E-SYS)
TEMP OVER
(E-TEMP)
TOC ERROR
(E-TOC)
TOC FULL
Tr. Protect
U TOC ERROR
(E-UTOC)
? DISC
(?DISC)
Meaning
PROTECTED
– 7 –
MD-MT20/20C/20W
3
Connection /
Conexión
Analog recording
Grabación analógica
Digital recording
Grabación digital
Microphone
Micrófono
MIC IN
PLUG IN
POWER
Stereo microphone
Micrófono estéreo
Recording side
Lado de grabación
OPTICAL/
LINE IN
To the line output jacks
on a stereo
A los enchufes de
salida de línea de un
equipo estéreo
LR
(RIGHT)
(DERECHO)
Analog cable included with this unit
Cable analógico suministrado con este
(LEFT)
(IZQUIERDO)
Playback side
Lado de reproducción
Recording side
Lado de grabación
OPTICAL/
LINE IN
Optical digital cable
(supplied)
Cable óptico digital
(suministrado)
Playback side
Lado de reproducción
Recording side
Lado de grabación
DIGITAL OUT
AUDIO OUT
1
2
4
3
5
5
1
Check the supplied accessories /
Compruebe los accesorios suministrados
2
Power source /
Alimentación
PORTABLE MINIDISC RECORDER
Quick Guide/Guía rápida
MD-MT20
Rechargeable battery power
Alimentación de la batería recargable
AC 120V, 60Hz
120V CA, 60Hz
Alkaline battery power
Alimentación de la pila alcalina
AC power
Alimentación de CA
AC 120V, 60Hz
120V CA, 60Hz
Carrying Bag x 1
Caja para el
transporte x 1
Analog Cable x 1
Cable analógico x 1
Optical Digital Cable
x 1
Cable óptico digital
x 1
AC Adaptor x 1
Adaptador de CA x 1
Headphones x 1
Auriculares x 1
Remote Control Unit
x 1
Controlador remoto
x 1
Rechargeable Nickel-
Metal Hydride Battery x 1
Batería recargable de
litio-ion x 1
1
2
3
Battery Carrying Case
x 1
Caja portabaterías x 1
OUICK GUIDE (MD-MT20 ONLY)
– 8 –
MD-MT20/20C/20W
2
1
3
2
1
3
4
4
Recording /
Grabación
To turn off the power:
Para desconectar la alimentación:
To remove the MiniDisc:
Para extraer el minidisco:
Turn off the power and move the OPEN lever in the di-
rection indicated by the arrow.
Desconecte la alimentación y mueva la palanca OPEN en el
sentido indicado por la flecha.
Press the ENTER/SYNC button.
Pulse el botón ENTER/SYNC.
Begin playback on the source equipment.
Inicie la reproducción en el equipo fuente.
Press the REC button.
Pulse el botón
REC.
When a sound, such as a person speaking, is
picked up by the microphone, recording will be-
gin automatically.
Connect the stereo microphone to the MIC IN jack.
Insert a recordable MiniDisc.
Inserte un minidisco grabable.
Recording from CDs or MDs (Synchro recording)
Grabación de discos compactos o minidiscos (Grabación sincronizada)
Recording from the microphone (Mic synchro recording)
Grabación de un micrófono (Grabación sincronizada con micrófono)
Press the ENTER/SYNC button to select the syn-
chro recording level. (This level can be changed,
even while recording.)
Press the /:OFF button while in the stop mode.
Pulse el botón
/:OFF estando en el modo de parada.
Connect the external equipment.
Conecte el equipo externo.
1
Insert a recordable MiniDisc.
Inserte un minidisco grabable.
2
Press the REC button.
Pulse el botón REC.
3
4
5
6
1
2
3
4
5
6
Press the/:OFF button.
Pulse el botón
/:OFF.
To stop recording:
Para detener la grabación:
Mientras se produce el sonido del equipo externo
conectado a este aparato, pulse el botón o
para ajustar el nivel de grabación.
Conecte el micrófono estéreo al enchufe MIC IN del
aparato principal.
Pulse el botón o para ajustar el nivel
de grabación.
Press the or button to adjust the
recording level.
Pulse el botón ENTER/SYNC para seleccionar el
nivel de la grabación sincronizada. (Este nivel podrá
cambiarse incluso durante la grabación.)
Cuando el micrófono capte un ruido, el de una per-
sona que hable por ejemplo, la grabación empezará
automáticamente.
While playing sound from the external
equipment connected to this unit, press the
or button to adjust the recording
level.
5
Playing a MiniDisc /
Reproducción de un minidisco
2
1
3
4
Insert the headphones plug firmly into the
headphones jack on the remote control unit.
1
Plug the remote control unit into the jack on
the main unit. Push the plug all the way in.
2
The power will be turned on automatically, and play-
back will start from the first track.
(Auto-play function)
La alimentación se conectará automáticamente, y la
reproducción empezará desde la primera pista.
(Función de reproducción automática)
To interrupt playback:
Para interrumpir la reproducción:
Press the button during playback.
To resume playback, press the button again.
Pulse el botón
durante la reproducción.
Para reanudar la reproducción, pulse de nuevo el botón
To turn off the power:
Para desconectar la alimentación:
Press the button.
In the following cases, the auto-play function will not work.
When the recordable MiniDisc write protection tab is closed
When the auto-play function has been canceled
Playback does not start when a MiniDisc is inserted:
La
reproducción no empieza cuando se inserta un
minidisco:
6
Sound control /
Control del sonido
Adjust the bass level.
Each time the BASS button is pressed, the tone will be
switched as follows:
Volume (0 - 30)
Volumen (0 - 30)
To stop playback:
Para detener la reproducción:
Press the /:OFF button.
Pulse el botón
/:OFF.
Press the /:OFF button while in the stop mode.
Pulse el botón
/
:OFF estando en el modo de parada.
3
Adjust the volume.
Press the + button to increase the volume and the –
button to decrease the volume.
Ajuste el volumen.
Pulse el botón + para aumentar el volumen y el botón –
para reducirlo.
BASS 1 ------- Bass sounds are emphasized slightly
.
BASS 2 ------- Bass sounds are emphasized more.
BASS 3 ------- Bass sounds are emphasized even more.
BASS OFF ----Bass emphasiz is canceled.
BASS 1 -------
Los sonidos graves se realzan ligeramente.
BASS 2 -------
Los sonidos graves se realzan más.
BASS 3 -------
Los sonidos graves se realzan aún más.
BASS OFF ----
El realce de los graves se cancela.
Inserte firmemente la clavija de los auriculares
en el enchufe de auriculares del controlador
remoto.
Enchufe el controlador remoto en el enchufe
del aparato principal. Empuje completamente
hacia adentro la clavija.
Pulse el botón
.
En los casos siguientes, la función de reproducción automática
no se activará.
Cuando esté cerrada la lengüeta de protección contra
escritura del minidisco grabable
Cuando haya sido cancelada la función de reproducción
automática
Ajuste el nivel de los graves.
Cada vez que pulse el botón BASS, el tono cambiará de la
forma siguiente:
Insert a MiniDisc.
Inserte un minidisco.
– 9 –
MD-MT20/20C/20W
DISASSEMBLY
Cares before disassembling
When assembling the machine after disassembling or repair, observe the following requirements so as to ensure safety and performance.
1. Remove the batteries from the machine, and take out the mini-disc.
2. When assembling after repair, be sure to restore the initial location of wires. Since the screws are small, incorrect fixing may result in malfunction.
3. When repairing, pay utmost attention to static electricity of IC.
STEP
REMOVAL
1 Bottom Cabinet 1. Screw .....................(A1) x7 10-1
2 Top Cabinet 1. Open the Top cabinet. 10-1
3 Key Switch/LCD 1. Flexible PWB......... (C1) x2 10-2
4 Mechanism Unit 1. Flexible PWB......... (D1) x2 10-2
5 Main PWB 1. Flat cable................(E1) x1 10-2
6 Audio PWB
PROCEDURE
2. Screw .....................(B1) x4
3. Screw .....................(B2) x1
2. Raise the rear part, and ..... 10-3
remove in the arrow direction.
2. Screw .....................(E2) x2
1.
Screw ......................(F1) x3 10-4
FIGURE
(A1)x2
ø1.4x2mm
Open Lever
ø1.4x2mm
(E2)x2
ø1.7x2.5mm
Main PWB
(B1)x2
ø1.4x2mm
OpenOpen
(B2)x1
pull
pull
pull
LCD
Key Switch
Top Cabinet
(A1)x2
ø1.4x2mm
Bottom
Cabinet
Figu re 10-1
Put the fold on the connector, and apply with the felt. Sagging may result in contact with the sheet metal.
(D1)x1
pull
pull
pull
pull
pull
(A1)x1
ø1.4x2mm
(B1)x2
ø1.4x2mm
(A1)x2
ø1.4x2mm
Felt
(D1)x1* Flexible PWB for optical pickup
Audio
PWB
(F1)x3
ø1.7x2.5mm
(C2)x2
Mechanism
(E1)x1
Unit
LCD
Key Switch
Caution:
Carefully handle the main PWB and flexible PWB. After removing the flexible PWB (1*) for the optical pickup from the connector, do not touch directly the front end of flexible PWB with your hand so as to prevent damage of optical pickup by static electricity.
Figure 10-2
Mechanism Unit
Audio PWB
Figure 10-4
Figure 10-3
– 10 –
REMOVING AND REINSTALLING THE MAIN PARTS
Remove the mechanism according to the disassembling meth­ods 1 to 4. (See Page 10.)
How to remove the spindle motor (See Fig. 11-1.)
1. Remove the solder joint (A1) x 1 of flexible PWB.
2. Remove the screws (A2) x 3 pcs., and remove the spindle motor.
How to remove the head up/down motor (See Fig. 11-2.)
1. Remove the solder joints (B1) x 2 of head up/down motor
lead wire.
2. Remove the screw (B2) x 1 pc., and remove the flexible PWB.
3. Remove the screw (B3) x 1 pc., and remove the head up/ down motor.
Note:
Take care so that the motor gear is not damaged. (If the gear is damaged, noise is caused.)
(A2)x3 ø1.4x2.8mm
Spindle Motor
Remove the solder joint (B1)x2
Head Up/Down Motor
MD-MT20/20C/20W
(A1)x1 Mechanism Flexible PWB Solder joint
MD Mechanism
Figure 11-1
(B3)x1 ø1.4x5.5mm
(B2)x1 ø1.4x1.5mm
How to remove the sled motor (See Fig. 11-3.)
1. Remove the stop washer (C1) x 1 pc., and remove the drive
gear (C2) x 1 pc.
2. Remove the screws (C3) x 2 pcs., and remove the sled
motor.
3. Remove the solder joints (C4) x 2 of flexible PWB.
Note:
Take care so that the motor gear is not damaged. (If the gear is damaged, noise is caused.)
How to remove the magnetic head (See Fig. 11-4.)
1. Remove the screws (D1) x4 which connects the magnetic
head to the head relay flexible PWB, remove the spring washers (D2) x 2 and remove the soldering joints (D3) x 2.
Note:
Mount carefully so as not to damage the magnetic head. (If the gear is damaged, noise is caused.)
How to reinstall the optical pickup unit (See Fig. 11-5.)
1. Remove the screw (E1) x 1 pc.
2. Slowly raise the optical pickup.
(C1)x1
Stop Washer
(C2)x1
Drive Gear
Figure 11-2
Figure 11-3
(D1)x2 ø1.4x2.2mm
MD Mechanism
(C3)x2 ø1.4x1.2mm
Sled Motor
(C4)x2 Mechanism Flexible PWB Solder Joint
MD Mechanism
(D2)x2 Spring Washer
Guide Shaft
Optical Pickup Unit
Figure 11-5
(E1)x1 ø1.7x3mm
Thrust Plate Spring
MD Mechanism
– 11 –
Magnetic Head
(D1)x1 ø1.4x1.5mm
Figure 11-4
(D3)x2 Solder joint
(D1)x1 ø1.2x1.6mm
MD Mechanism
MD-MT20/20C/20W
ADJUSTMENT
Test disc
MD adjustment needs two types of disc, namely recording disc (low reflection disc) and playback-only disc (high reflection disc).
Type
Test disc
Parts No.
1 High reflection disc MMD-110 (TEAC Test MD) 88GMMD-110 2 Low reflection disc MMD-212 (TEAC Test MD) 74-minute disc 88GMMD-212 3 Low reflection disc MMD-213A (TEAC Test MD) 80-minute disc 88GMMD-213A 4 Low reflection disc Recording minidisc UDSKM0001AFZZ
Note: Use the low reflection disc on which music has been recorded.
Entering the TEST mode
1. Setting at port (power nonconnected state)
(1) Set the port as follows. TEST1 : "Low" (TP416) TEST0 : "High" (2) Turn the Power ON. (3) Test Mode STOP [ T E S T _ ]
2. Setting by special button operation (in standby state)
(1) Holding down the DISP button and ENTER button, press the PLAY button. (2) Normal mode setting initialization (BASS setting, VOL setting, etc.) *Since the unit is changed to the setting for production line inspection , be sure to set it to the default setting state in the following default setting procedure before returning it to the user. (3) Indication of microcomputer version for one second [ 3 1 8 A f X ]
Destination
Microcomputer version
(4) Whole LCD lighting for 2 seconds (5) Test Mode STOP [ T E S T _ ] *When the PLAY button is pressed during indication (3) and (4), the process proceeds to (5).
EEPROM version
Leaving the TEST mode
(1) Press the STOP button in the TEST mode stop state or version indicating state or whole LCD lighting state.
Shipping setting method
Holding down simultaneously the VOLUME-DOWN Button and PLAY Button of the set unit without disc, supply the power from the DC IN plug. After the indication "INIT" -> "BYE OK" disappears, release the power supply of DC IN.
Test Mode
1. AUTO 1 Mode • Perform preliminary automatic adjustment.
2. AUTO 2 Mode
3. TEST-PLAY Mode
4. TEST-REC Mode
5. MANUAL 1 Mode
6. MANUAL 2 Mode
• If the combination of mechanism and pickup PWB has been changed, be sure to start from
AUTO1.
• Perform ATT (attenuator) automatic adjustment.
• Perform continuous playback (error rate display, jump test)
• Continuous playback from the specified address is performed.
• 1 line, 10 lines or 384 lines manual jump is performed.
• C1 error rate display (pit section), ADIP error rate display (groove section)
• The temperature correction is performed only when servo start is performed, but the posture correction is not performed during continuous playback.
• Continuous record from the specified address is performed.
• Change of record laser output(servo gain is also changed according to laser output).
• The temperature correction is performed only when servo start is performed, but the posture correction is not performed during continuous recording.
• Temperature is displayed. (Updating in real time)
• Seeing the displayed adjustment value, perform
preliminary manual adjustment. (Error rate indication, jump test)
• Temperature is displayed. (Updating in real time)
• Seeing the displayed adjustment value perform manfully the preliminary adjustment.
(Error rate indication, jump test)
• Continuous playback is performed
(error rate display, jump test).
7. RESULT 1 Mode
8. RESULT 2 Mode
9. DIGITAL INPUT Mode
10. ERROR INFORMATION Mode • Error information is initialized
11. NORMAL Mode
12. EEPROM Mode
13. INNER Mode
• The value adjusted in AUTO1 or MANUAL1 is indicated.
• (Execution in servo "OFF" state").
• The value adjusted in AUTO 2 or MANUAL 2 is indicated.
• Adjustment value is changed manually. (error rate display, jump test).
• Digital input information is displayed.
• Error information is displayed.
• The mode is changed from the TEST mode to the normal mode without adjustment.
• In the normal mode the internal operation mode, memory capacity, etc. areindicated.
• In the normal mode both temperature correction and posture correction are perfomed.
• Factors of digital servo are changed manually. (Each servo is turned on individually.)
• Cut-off frequency of BASS1, BASS2 and BASS3 is selected manually.
• Temperature detection terminal voltage is measured, and the reference value is set.
• Defaults are selected and set.
• Setting of EEPROM protect area is updated. (In case of protect releasing)
• Determine the position where the INNER switch is turned on. (only high reflection disc).
• The temperature correction is performed only when servo start is performed, but the posture correction is not performed.
– 12 –
MD-MT20/20C/20W
Operation in each TEST mode
1. AUTO1 Mode
• When the STOP button is pressed while the AUTO1 menu appears or during automatic adjustment, the mode changes to the TEST mode stop state. At this time the adjustment value is not output.
• Be sure to adjust, using the specified disc MMD-213A or MMD-212.
At this time release the EEPROM (IC402) protection. (Refer to EEPROM write procedure.)
• Adjustment NG; Adjustment item out of range, focus ON failure, and adjustment error
• When the PLAY button is pressed while ADJ. OK is displayed, AUTO2 is executed.
2. AUTO2 Mode
• When the STOP button is pressed while the AUTO2 menu appears or during automatic adjustment, the mode changes to the TEST mode stop state. At this time the adjustment value is not output.
• Adjustment NG; Adjustment item out of range, and adjustment error.
• When the PLAY button is pressed while ADJ. OK is displayed,TEST_PLAY is executed.
3. TEST-PLAY Mode
• When the STOP button is pressed while the TEST-PLAY menu appears, or in TEST-PLAY or continuous playback mode, the mode changes to the TEST mode stop state.
• When the PLAY button is pressed while the TEST-PLAY menu appears,continuous playback is initiated from the current pickup position.
• Whenever the DISP button is pressed in the TEST-PLAY menu, the target address changes as follows.
When the PLAY button is pressed while a target address is displayed, continuous playback is performed after searching that address.
• Each time the MODE button is pressed while the TEST-PLAY mode target address is displayed, the digit which is changed by pressing the SKIP UP/DOWN button is changed as follows.
• When the SKIP UP button is pressed in the TEST-PLAY mode target address is displayed, the digit of address specified by the MODE button is set to +1h. (0 to F)
• When the SKIP DOWN button is pressed in the TEST-PLAY mode target address is displayed, the digit of address specified by the MODE button is set to -1h. (0 to F) * When the SKIP UP/DOWN button is held down, the setting changes continuously, one cycle being 100 ms.
• When the BASS button is pressed in the continuous playback mode, the number of jump lines changes as follows.
* After the number of jump lines is indicated for one second, the address indication is restored. [ T R _ ]
• When the SKIP UP button is pressed in the continuous playback mode, the specified number of lines is jumped in the FWD direction.
• When the SKIP DOWN button is pressed in the continuous playback mode, the specified number of lines is jumped in the REV direction. * When the SKIP UP/DOWN button is held down, jump is repeated every approx. 100 ms.
•Whenever the DISP button is pressed in the continuous playback mode, the indication changes as follows. * Pre-mastered disc
* Recordabl disk
0032 — 03C0 — 0700 — 08A0 — 0950— 0032 —
0032 — 0032 — 0032 — 0032 —
1 — 10 — 384 — 1
Continuous playback (SUBQ address indication) [ S Q ]
|
Continuous playback (C1 error indication) [ C E ]
|
Continuous playback (SUBQ address indication) [ S Q ]
Continuous playback (ADIP address indication) [ A P ]
|
Continuous playback (C1 error indication) [ C E ]
|
Continuous playback (ADIP error indication) [ A E ]
|
Continuous playback (ADIP address indication) [ A P ]
4. TEST-REC Mode
• When the STOP button is pressed while the TEST-REC menu appears, or in the TEST-REC mode or continuous record mode, the mode changes to the TEST mode stop state.
• When the PLAY button is pressed while the TEST-REC menu appears, the continuous record is initiated from the current pickup position.
• Whenever the DISP button is pressed in the TEST-REC menu, the target address changes as follows.
0032 — 03C0 — 0700 — 08A0 —0950 — 0032 —
When the PLAY button is pressed while a target address is displayed, continuous playback is performed after searching that address.
• Whenever the MODE button is pressed in the TEST-REC mode target address is displayed, the digit which is changed by the SKIP UP/
DOWN button changes as follows.
0032 — 0032 — 0032 — 0320 —
• When the SKIP UP button s pressed in the TEST-REC mode target address is displayed, the digit of address specified by the BASS button is set to +1h.(0 to F)
• When the SKIP DOWN button is pressed in the TEST-REC mode target address is displayed, the digit of address specified by the BASS button is set to -1h. (0 to F)
* When the SKIP UP/DOWN button is held down, the setting changes continuously, one cycle being 100 ms.
– 13 –
MD-MT20/20C/20W
5. NORMAL Mode
• When the STOP button is pressed while the NORMAL menu appears, the mode changes to the TEST mode stop state.
• Indication during operation Indication of memory capacity on main unit LCD [ ] + Level meter
: Internal mode : Address (Cluster section)
• Selection of sound volume, BASS, etc. is possible (without indication)
• Recording is also possible.
• If the STOP button is pressed during operation in the NORMAL mode, the NORMAL mode is canceled, and the power is turned off.
6. Error data display Mode
• Reversing when SKIP DOWN button is pressed
• When the STOP button is pressed while the error data indication menu appears or during error data indication, the mode changes to the TEST mode stop state.
• Error data 0 is the latest error.
• Error which occurred in the TEST mode is also stored in the memory.
• When the DISP button is pressed while the error data indication menu appears, the error data is initialized. [ C L E A R _ ]
: Error Code
Explanation of error history code
12h : RF side FG, TG, and TCRS adjustment termination failure 13h : Adjustment servo retraction excessive retrial 16h : C. IN detection time-over 17h : A, B, E, F, and TCRSO offset measurement value out of
tolerable range 21h : Focus retraction completion allowable time-over 23h : Track search completion allowable time-over 24h : Disc linear speed measurement failure 32h : P-TOC read failure 42h : U-TOC read failure 44h : U-TOC write data write disabled/read check error 52h : SD write data write disabled 71h : Pickup position initialization time-over 72h : EEPROM data read check sum error 73h : Record head drive disabled (by EJECT lever) 82h : Power overvoltage detection 91h : Ambient temperature is higher that the allowable tempera-
ture.
: Address (Sector section)
7. INNER Mode
• when the STOP button is pressed on the INNER menu (SQ______ ), the state is changed to the TEST mode STOP state.
• : Address
– 14 –
MD-MT20/20C/20W
EEPROM (IC402) writing procedure
1. Procedure to replace EEPROM and write initial value of microcomputer in EEPROM
(1) Replace EEPROM. (2) Deprive EEPROM of protection (connect the pins 8 and 6 of IC402). (3) Refer to the latest EEPROM data list. (4) Press the Display button, Ente button and Play button to start the test mode. (5) Version display
[ V e r . ]
(6) The whole LCD lights. (7) Test mode stop state.
[ T E S T ]
(8) Press the "BASS" button, and press twice the "SKIP DOWN" button.
[ E E P R O M ]
(9) Perform the operation to display "EEPROM SETTING MODE CHART", compare the EEPROM DATA LIST with the display,
and set according to the EEPROM DATA LIST with the VOL UP or VOL DOWN key.
(10)
Set the temperature reference. (Refer to the Temperature Reference Setting Method.)
(11)
Set according to the EEPROM DATA LIST.
(12)
Press the Stop button.
[ T E S T ]
(13)
Press the Stop button.
(14)
After data is written in EEPROM, turn off power .
(15)
Restore protection of EEPROM (Disconnect connection made in Step (2) above).
X
EEPROM version (f ~ Z) Microcomputer ROM version
2. Temperature reference setting method
[1] Measurement, calculation and setting procedure
(1) Set the TEST mode.
Set TEST 1, 0 = '01', and turn on power (or set PLAY ON in standby state). (2) Start the EEPROM mode 'Temp' menu.
Key operation in order of BASS, SKIP-DOWN x 2 times, PLAY, PLAY in the test mode STOP state.
'TM$$%%' is displayed. ($$= Temperature code, %% = Temperature reference) (3) Once press SKIP-UP, and determine the displayed microcomputer TEMP input AD value.
• 'TPin##' is displayed. (## = TEMP input AD value) (4) At the ambient temperature, determine the temperature corrected value from the temperature measurement value
correction table.
(5) Determine the temperature reference, using the following formula.
• Temperature reference = Microcomputer TEMP input AD value + Temperature corrected value (6) Set the temperature reference value by button operation , and check whether the temperature code indication corresponds to "Temperature
Code Identification Table".
[2] Temperature measurement value correction table
Ambient
temperature
+ 9oC ~ +11oC - 05h + 10.0oC +12oC ~ +14oC - 04h + 12.7oC +15oC ~ +16oC - 03h + 15.4oC +17oC ~ +19oC - 02h + 18.2oC +20oC ~ +22oC - 01h + 20.9oC +23oC ~ +24oC ± 00h + 23.6oC +25oC ~ +27oC + 01h + 26.3oC +28oC ~ +30oC + 02h + 29.0oC +31oC ~ +33oC + 03h + 31.8oC
Temperature
correction
Center
temperature
Ambient
temperature
- 9oC ~ +10oC 08h + 0.5oC
+ 3oC ~ +21oC 07h + 12.5oC +15oC ~ +33oC 06h + 23.6oC +26oC ~ +43oC 05h + 35.0oC
Temperature
correction
Center
temperature
– 15 –
MD-MT20/20C/20W
EEPROM DATA LIST (EEPROM version f)
TEMP setting
Item display Set values
T M _ _ Calculate values
Fucus setting
Item display Set values
F G _ _ B 0 H F F 1 _ 7 0 H F F 2 _ E 8 H F Z H _ E D H F L n _ 0 A H D J G _ 1 4 H F L V _ 3 3 H W T f _ 2 0 H F S S _ E 9 H
Tracking setting
Item display Set values
T G _ _ 4 8 H T F 1 _ 7 0 H T F 2 _ E 0 H T F S _ 0 0 H T B o _ 4 4 H T B t _ 2 0 H T K o _ 4 4 H T K t _ 1 D H T D o _ 6 7 H T D t _ 3 4 H T G R _ 0 0 H S C t _ 4 0 H S C m _ 5 3 H C L p _ 1 8 H C L r _ 2 8 H J P I _ 0 1 H K 1 0 _ 6 5 H
Spindle setting
Item display Set values
S P G _ 1 4 H S P i _ E 0 H S P m _ A 0 H S P o _ 6 8 H S P 1 _ 1 0 H S P 2 _ 6 0 H S P 3 _ F 2 H S P 4 _ F 2 H S P 5 _ 1 0 H S P D _ 7 F H S P K _ E B H
BASS setting
Item display Set values
B S 1 _ 3 F H B S 2 _ 1 F H B S 3 _ E 2 H
Sled setting
Item display Set values
S L G _ D F H S L 2 _ 2 0 H S L M _ 7 F H S L V _ D 7 H S K k _ 7 2 H S K t _ 7 0 H S K m _ 7 8 H W T m _ 2 4 H M V 1 _ 4 F H M V 2 _ A A H S R V _ 0 A H
ADJ. SET setting
Item display Set values
C O K _ A 0 H F A T _ C 0 H T A T _ 3 E H C A T _ 2 0 H F A B _ E 0 H
EQ. SET setting
Item display Set values
H Q 1 _ 9 0 H H Q 2 _ 9 0 H H S G _ 1 1 H H S O _ F D H L Q 1 _ 9 0 H L Q 2 _ 9 0 H L S G _ 1 1 H L S O _ 0 0 H G Q 1 _ 9 8 H G Q 2 _ 8 4 H G S G _ 1 1 H F L p _ 0 8 H
Control setting
Item display Set values
C T 0 _ 0 5 H C T 1 _ 1 1 H C T 2 _ 7 F H C T 3 _ 3 0 H R C 0 _ C 0 H R C 1 _ F E H S Y C _ A 6 H P W L _ 0 3 H D R 1 _ 9 2 H D R 2 _ C 8 H I N 1 _ D 3 H I N 2 _ 6 4 H I N 3 _ D 2 H
I N H _ 6 4 H D R H _ C 8 H P L E _ 1 B H R C E _ 4 2 H E L T _ 7 6 H S L T _ 4 3 H S P M _ 0 0 H M S L _ 0 0 H U S 0 _ 0 0 H U S 1 _ 0 0 H U S 2 _ 0 0 H
– 16 –
Loading...
+ 36 hidden pages