Sharp LC-M3700, LC-M3710 User Manual

Download

INPUT

RETURN

STANDBY/ON

ENLARGE

WIDE

LCD MONITOR

ENTER

VOL

LC-M3700/LC-M3710

OPERATION MANUAL

MODE D’EMPLOI

ENGLISH

DEUTSCH

LC-M3700

FRANÇAIS

LC-M3710

SHARP CORPORATION

BEDIENUNGSANLEITUNG

MANUAL DE MANEJO

WIDE LCD MONITOR

ESPAÑOL

BREITBILD-LCD-MONITOR MONITEUR GRAND ÉCRAN À

CRISTAUX LIQUIDES

MONITOR LCD PANORÁMICO

OPERATION MANUAL BEDIENUNGSANLEITUNG MODE D’EMPLOI MANUAL DE MANEJO

Printed on 100% post-consumer recycled paper. Gedruckt auf 100% wiederverwertungs Papier. Imprimé sur 100% de papier recyclé. Impreso en 100% de papel reciclado de postconsumo.

Cover.p65 03.7.25, 1:24 PM1

Printed in Japan Gedruckt in Japan Imprimé au Japon Impreso en Japón TINS-A842WJZZ 03P07-JKK

LC-M3700 LC-M3710

WIDE LCD MONITOR

ENGLISH

OPERATION MANUAL

ENGLISH

IMPORTANT: To aid reporting in case of loss or theft, please record the product’s model and serial numbers in the space provided. The numbers are located in the rear of the product.

Model No.:

Serial No.:

U.S.A. ONLY

IMPORTANT INFORMATION

WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE

THIS PRODUCT TO RAIN OR MOISTURE.

The lightning flash with arrowhead symbol,

CAUTION

RISK OF ELECTRIC SHOCK DO NOT OPEN

CAUTION: TO REDUCE THE RISK OF

ELECTRIC SHOCK, DO NOT REMOVE COVER. NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

within an equilateral triangle, is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.

The exclamation point within a triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the product.

IMPORTANT INFORMATION (Continued)

WARNING: FCC Regulations state that any unauthorized changes or modifications to this

equipment not expressly approved by the manufacturer could void the user’s authority to operate this equipment.

CAUTION: Use the supplied AC cord as it is.

Do not remove the core part from the AC cord, and do not change the way of winding cables around the core part.

INFORMATION:

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Relocate or adjust the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

U.S.A. ONLY

CAUTION

Danger of explosion if battery is incorrectly replaced.

Replace only with the same or equivalent type

recommended by the manufacturer.

Dispose of used batteries according

to the manufacturer’s instructions.

2

DEAR SHARP CUSTOMER

Thank you for your purchase of a SHARP LCD product. To ensure safety and many years of trouble-free operation of your product, please read the Safety Precautions carefully before using this product.

SAFETY PRECAUTIONS

Electricity is used to perform many useful functions, but it can also cause personal injuries and property damage if improperly handled. This product has been engineered and manufactured with the highest priority on safety. However, improper use can result in electric shock and/or fire. In order to prevent potential danger, please observe the following instructions when installing, operating and cleaning the product. To ensure your safety and prolong the service life of your LCD product, please read the following precautions carefully before using the product.

1. Read instructions—All operating instructions must be read and understood before the product is operated.

2. Keep this manual in a safe place—These safety and operating instructions must be kept in a safe place for future reference.

3. Observe warnings—All warnings on the product and in the instructions must be observed closely.

4. Follow instructions—All operating instructions must be followed.

5. Cleaning—Unplug the power cord from the AC outlet before cleaning the product. Use a damp cloth to clean the product. Do not use liquid cleaners or aerosol cleaners.

6. Attachments—Do not use attachments not recommended by the manufacturer. Use of inadequate attachments can result in accidents.

7. Water and moisture—Do not use the product near water, such as bathtub, washbasin, kitchen sink and laundry tub, swimming pool and in a wet basement.

8. Stand—Do not place the product on an unstable cart, stand, tripod or table. Placing the product on an unstable base can cause the product to fall, resulting in serious personal injuries as well as damage to the product. Use only a cart, stand, tripod, bracket or table recommended by the manufacturer or sold with the product. When mounting the product on a wall, be sure to follow the manufacturer’s instructions. Use only the mounting hardware recommended by the manufacturer.

9. When relocating the product placed on a cart, it must be moved with utmost care. Sudden stops, excessive force and uneven floor surface can cause the product to fall from the cart.

10. Ventilation—The vents and other openings in the cabinet are designed for ventilation. Do not cover or block these vents and openings since insufficient ventilation can cause overheating and/or shorten the life of the product. Do not place the product on a bed, sofa, rug or other similar surface, since they can block ventilation openings. Do not place the product in an enclosed place such as a bookcase or rack, unless proper ventilation is provided or the manufacturer’s instructions are followed.

11. Power cord protection—The power cords must be routed properly to prevent people from stepping on them or objects from resting on them.

12. The LCD panel used in this product is made of glass. Therefore, it can break when the product is dropped or applied with impact. Be careful not to be injured by broken glass pieces in case the LCD panel breaks.

13. Overloading—Do not overload AC outlets or extension cords. Overloading can cause fire or electric shock.

14. Entering of objects and liquids—Never insert an object into the product through vents or openings. High voltage flows in the product, and inserting an object can cause electric shock and/or short internal parts. For the same reason, do not spill water or liquid on the product.

15. Servicing—Do not attempt to service the product yourself. Removing covers can expose you to high voltage and other dangerous conditions. Request a qualified service person to perform servicing.

Introduction

and Installation

Connection

Basic Operation

PC Operation

Adjustments

Settings and

Troubleshooting and

Specifications

Appendix

SAFETY PRECAUTIONS (Continued)

16. Repair—If any of the following conditions occurs, unplug the power cord from the AC outlet, and request a qualified service person to perform repairs. a. When the power cord or plug is damaged. b. When a liquid was spilled on the product or when objects have fallen into the product. c. When the product has been exposed to rain or water. d. When the product does not operate properly as described in the operating instructions.

Do not touch the controls other than those described in the operating instructions. Improper adjustment of controls not described in the instructions can cause damage, which often requires extensive

adjustment work by a qualified technician. e. When the product has been dropped or damaged. f. When the product displays an abnormal condition. Any noticeable abnormality in the product indicates

that the product needs servicing.

17. Replacement parts—In case the product needs replacement parts, make sure that the service person uses replacement parts specified by the manufacturer, or those with the same characteristics and performance as the original parts. Use of unauthorized parts can result in fire, electric shock and/or other danger.

18. Safety checks—Upon completion of service or repair work, request the service technician to perform safety checks to ensure that the product is in proper operating condition.

19. Wall or ceiling mounting—When mounting the product on a wall or ceiling, be sure to install the product according to the method recommended by the manufacturer.

20. Heat sources—Keep the product away from heat sources such as radiators, heaters, stoves and other heat-generating products (including amplifiers).

21. Power source—This product must operate on a power source specified on the specification label. If you are not sure of the type of power supply used in your home, consult your dealer or local power company. For units designed to operate on batteries or another power source, refer to the operating instructions.

The LCD panel is a very high technology product with 3,147,264 thin film transistors, giving you fine picture details. Occasionally, a few non-active pixels may appear on the screen as a fixed point of blue, green or red. Please note that this does not affect the performance of your product.

WARNING:

To reduce the risk of fire or electric shock, do not expose this product to rain or moisture.

WARNING:

This is a class A product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures.

4

CONTENTS

Page

Dear SHARP Customer........................................................................... 3

Safety Precautions.................................................................................. 3

Introduction ............................................................................................. 5

Features ................................................................................................. 6

Part Names – Display ............................................................................ 8

Removing the terminal cover ................................................................. 9

Part Names – Remote Control Unit ..................................................... 10

Removing the battery cover ................................................................. 11

Supplied Accessories ........................................................................... 12

Connection and Installation ................................................................. 13

Connecting Peripheral Equipment ....................................................... 13

Connecting external speakers ............................................................. 18

Connecting the AC cord ....................................................................... 19

Connecting multiple monitors ............................................................... 20

Mounting options .................................................................................. 23

Bundling cables .................................................................................... 29

Basic Operation .................................................................................... 30

Turning on Power ................................................................................. 30

Main POWER switch ............................................................................ 30

STANDBY/ON ...................................................................................... 30

Remote Control Unit............................................................................. 31

Menu Items .......................................................................................... 32

Menu option selection .......................................................................... 32

Menu screen explanation ..................................................................... 33

PC (analog) input mode menu items ................................................... 34

AV input mode menu items .................................................................. 35

Language setting .................................................................................. 36

PC Operation ......................................................................................... 37

PC connection ...................................................................................... 37

Communication conditions ................................................................... 37

Communication procedure ................................................................... 38

RS-232C command table ..................................................................... 46

Settings and Adjustments.................................................................... 51

Picture .................................................................................................. 51

Audio .................................................................................................... 53

Power control ....................................................................................... 53

Setup .................................................................................................... 54

Option ................................................................................................... 57

Detailed explanation............................................................................. 58

Troubleshooting and Specifications ................................................... 65

Troubleshooting ................................................................................... 65

Specifications ....................................................................................... 67

Optional Accessories ........................................................................... 67

Appendix ................................................................................................ 68

Appendix 1: PC Compatibility Chart ..........................................................

Appendix 2: Dimensional Drawings ...........................................................

Appendix 3: Menu Option Reference Chart ...............................................

68 69 70

Introduction

Features

Numbers within refer to the main page(s) where the topic is explained.

HIGH-DEFINITION (HD) PANEL

A large, flat LCD display panel with 3.15 million pixels lets you enjoy a detailed, high-

•

definition picture from a digital TV or a PC.

ASV* LOW-REFLECTION BLACK TFT LCD PANEL

SHARP’s unique ASV* low-reflection BLACK TFT LCD panel provides higher luminance,

•

higher contrast, and a wider viewing angle. This reduces reflection in the monitor when it is placed near a window, and ensures brighter, more vivid image reproduction. With a wide viewing angle of 170 degrees, both horizontally and vertically, the image is beautiful, even when viewed off axis.

* ASV … Advanced Super View

CABINET DESIGN ENABLES VERTICAL AND HORIZONTAL INSTALLATION

When mounted vertically, this monitor requires images coded for a vertical screen. It

•

does not have image rotation capability.

EQUIPPED WITH A VARIETY OF TERMINALS 

INPUT1 Terminals are provided for two types of video input signal. Input Select

•

Video Input (BNC-terminal) NTSC (3.58/4.43)/PAL/SECAM (*1) S-video Input (S-terminal) NTSC (3.58/4.43)/PAL/SECAM (*1)

INPUT2 This terminal can be set for input or output. INPUT2 Select

•

Video Input (RCA-terminal) NTSC (3.58/4.43)/PAL/SECAM (*1)

INPUT3 This terminal enables selection of the video signal type.  Input Select

•

COMPONENT/RGB Input (BNC-terminal)

COMPONENT 480i/480p/576i/576p/1080i/720p (*2) RGB Conforms to PC analog input. Appendix 1 (*2, *3)

•

Analog Input (D-Sub terminal) Digital Input (DVI terminal)

*1: There is a setting for auto-detection of the color system. (This is set to “Auto” at factory shipment.) *2: Frequency is auto-detected. *3: The INPUT3 (RGB) and PC (analog) inputs are compatible with Sync On Green input. PC (analog) input is

compatible with Csync input.

VGA/SVGA/XGA/SXGA and others VGA/SVGA/XGA/SXGA and others

 Appendix 1 (*2, *3)

 Appendix 1

6

COMPATIBLE WITH VARIOUS COLOR SYSTEMS

Compatible with NTSC (3.58/4.43), PAL (50/60) and SECAM.

•

Features (Continued)

Numbers within refer to the main page(s) where the topic is explained.

ENLARGEMENT FUNCTION 

Allows output of enlarged images for 4- or 9-screen (“2×2” or “3×3”) setups, without using

•

a special-purpose external device.

CHAIN CONNECTION OF MULTIPLE MONITORS

Enables chain connection of monitors using video signal output (composite-video/D-Sub)

•

terminals. Enables individual control via PC of multiple sets connected in a daisy chain using RS-

•

232C cables. 

EXTERNAL CONTROL AND STATUS MONITORING FROM A PC

The monitor can be controlled in various ways from a PC.

•

Multiple monitors can be individually controlled by connecting them in a daisy chain.

•

EXTERNAL SPEAKERS CAN BE CONNECTED

Introduction



Compatible speakers: L/R, 8 ohm, 10W or larger

•

EQUIPPED WITH BUILT-IN MONITOR SPEAKER (MONO)

When activated from the menu screen, you can check the audio input status using the

•

built-in monitor speaker (mono).

CONTROL LOCK FUNCTIONS 

The monitor is equipped with various operation lock functions to prevent unintended

•

operation or mischief. (The PIN can be set by the user.)

Fluorescent Tubes

■ The fluorescent tubes in this product have a limited lifetime.

» If the screen gets dark, flashes, or does not turn on, change the fluorescent tubes with new

exclusive ones.

Expected lifetime: ............... 60,000 hours for LC-M3700 (horizontal mount)*

40,000 hours for LC-M3710 (vertical mount)* *When “Brightness” is set to a center value.

» For more information, please contact your product dealer.

■ Because of the property of fluorescent tubes, the screen may flash during the initial period of use. If this happens, please turn off the main power switch on the back of the monitor and turn on again to confirm operation.

Part Names – Display

Numbers within refer to the main page(s) where the topic is explained.

Front view

About LC-M3710:

The SHARP logo for the LC-M3710 model is on the vertical base.

LC-3700 LC-3710

Liquid Crystal Display panel

Remote control sensor

When using the

remote control, point it towards here.

STANDBY/ON indicator

Side control panel (See below.)

Panel side

STANDBY/ON button

Side control panel

LEFT

RIGHT

DOWN

ENTER

VOL

INPUT

Menu operation buttons

RIGHT

LEFT

DOWN

ENTER

VOL +/–

INPUT

Cursor control

8

Rear view

Part Names – Display (Continued)

Built-in monitor speaker

Introduction

SPEAKER (R) External speaker terminal (right)

POWER···················· Main power on/off switch

INPUT2 (INPUT/ OUTPUT)

VIDEO OUTPUT

AC Input terminal···············

2 1

INPUT1

PC (DIGITAL) INPUT

INPUT3

SPEAKER (L) External speaker terminal (left)

INPUT3/PC (ANALOG) OUTPUT············

PC (ANALOG) INPUT··················

RS-232C INPUT··············

RS-232C OUTPUT········

Removing the terminal cover

Lower claw

Upper claw

Removing the terminal cover

1. Hold down the two claws at the top of the terminal cover, and pull the cover toward you so it opens a little.

2. Slowly lift the cover so the three claws at the bottom come loose from the claw holes in the console.

Part Names – Remote Control Unit

Numbers within refer to the main page(s) where the topic is explained.

Remote control unit

STANDBY/ON

INPUT

RETURN

ENLARGE

Signal transmitter

STANDBY/ON

INPUT

RETURN

ENTER

ENLARGE

LCD MONITOR

VOL

WIDE

VOL +/– ··································

MENU····································

Cursor control ('/"/\/|)············

ENTER··································

WIDE·····································

10

Part Names – Remote Control Unit (Continued)

Removing the battery cover

Introduction

Gently hold down and press in the arrow direction.

Remote control operation range

Cautions regarding remote control unit

» Do not expose the remote control unit to shock. In addition, do not

expose the remote control unit to liquids, and do not place it in an area with high humidity.

» The remote control unit may not work properly if the remote control

sensor is under direct sunlight or strong lighting. In such cases, change the angle of the lighting or the monitor, or operate the remote control unit closer to the remote control sensor.

Cautions regarding batteries

Improper use of batteries can result in chemical leakage or explosion. Be sure to follow the instructions below.

» Do not mix old and new batteries, or batteries of different

types.

Caution

» Do not charge or disassemble batteries. » Place batteries with their terminals corresponding to the

± and — as indicated in the compartment.

» Do not short-circuit the batteries.

» The batteries supplied with this product may

NOTE:

have a shorter life expectancy due to storage conditions. Replace with new batteries at the earliest opportunity.

» If you will not use the remote control for a long

time, remove its batteries.

» If the remote control does not work, even with

new batteries, take the batteries out, check whether they are facing the right way, then replace them.

10°

6 m

7 m

10°

If the remote control unit does not work well:

» Objects between the remote control unit and the remote

control sensor may prevent proper operation.

» Replace the batteries when they run low as this may shorten

the remote control operation range.

Remote control sensor

6 m

Supplied Accessories

Make sure the following accessories are provided with the product.

Remote control unit (× 1)

STANDBY/ON

INPUT

RETURN

ENLARGE

LCD MONITOR

(RRMCGA186WJSA)

VOL

ENTER

WIDE

“AA” size battery (× 2)

(UBATU0013TAZZ)

AC cord, 9 ft.10-

Cable clamp (× 1)

(XTBS940P-16000)

Cable binder (× 3)

/8″(3 m) (× 1)

(QACCDA024WJPZ)

Page 19

Screw (× 1)

(LHLDW1118CEZZ)

Page 19

Pages 11, 30 - 32 Page 11

» Operation manual × 1

(LHLDWA017WJKA)

Page 29

Terminal cover mounting screw (× 2)

Flat washer (× 2)

(XWHS960-16180)

(XBBS960P20000)

Page 29

Caution:

» This monitor is equipped with a temporary stand when shipped from the factory. Please note this stand is for temporary use

only until the monitor is properly mounted. Be sure to use a special-purpose AN-37ST1 table stand or AN-37AG1 wallmount bracket (both optional). Mounting Options.

12

Connecting Peripheral Equipment

INPUT1

INPUT1 audio

INPUT 1

AUDIO

R - - L

VIDEOS-VIDEO

S-video

■ INPUT1: Terminals are provided for two types of video input signal. Input Select

Video

Introduction

and Installation

Connection

Video

S-video

Terminal type

BNC

S terminal

NTSC (3.58/4.43), PAL, SECAM (*1)

Compatible signals

No matter which video signal is selected, the system uses the signal input to the audio terminals for audio.

Related topic:

Input Select

*1 “Auto” (automatic color system detection) is factory preset value.

Color System

Connecting Peripheral Equipment (Continued)

INPUT2

INPUT2 audio

INPUT 2 (INPUT/OUTPUT)

AUDIOR - - L

VIDEO

Video

■ INPUT2: Input or output can be selected for INPUT2. (*1) INPUT2 Select

This setting cannot be switched when INPUT2 is currently being displayed.

Terminal type

RCA

NTSC (3.58/4.43), PAL, SECAM (*2)Video

Compatible signals

When this is set to “Output”, video signals input from the INPUT1 video input terminal are output. (*3) An audio signal is output with this setting (i.e. the audio signal corresponding to the video currently being displayed). (*4)

Related topic:

INPUT2 Select

*1 “Input” is factory preset value. *2 “Auto” (automatic color system detection) is factory preset value.

*3 Outputs video from INPUT1, regardless of the currently displayed signal. *4 If the “INPUT2 Select” is set to “Output”, audio output is as follows.

Example 1 Input Selection “Input Select”

: INPUT1 : AV

INPUT2 video output: Video from INPUT1 INPUT2 audio output: Audio from INPUT1

Example 2 Input Selection “Input Select”

INPUT2 video output: Video from INPUT1 INPUT2 audio output: Audio from INPUT3

Color System

: INPUT3 : RGB

14

INPUT3

Connecting Peripheral Equipment (Continued)

Horizontal

Input Select: RGB

Input Select: COMPONENT

■ INPUT3: Either COMPONENT or RGB can be selected for the input video signal. Input Select

COMPONENT

The signal is input with the Y/Pb/Pr (Y/Cb/Cr) terminals. The HD and VD terminals are not used. Video adjustment options on the menu are the AV type. Compatible input range: 480i/576i, 480p/576p, 1080i (50Hz (*4) /60Hz), 720p (60Hz). (*1)

sync signal (H sync)

INPUT 3

Vertical sync signal (V sync)

AUDIOPr/Cr/RPb/Cb/B VDHDY/G

INPUT3 audio

and Installation

Connection

RGB

The monitor operates using Video (RGB) and Sync (HD/VD) signals, just like a PC (analog). Supported sync signals are ordinary separate sync (HD/VD) and Sync On Green. (*2) (*3) Video adjustment options on the menu are the PC type. Compatible input range: Conforms to PC (analog). Appendix 1

Related topic:

Input Select

*1 Auto-detects video signal frequency. *2 Automatic sync signal type detection *3 Sync signal presence is detected in the order: Separate Sync → Sync On Green. If for some reason

Separate Sync is not input, the system will operate assuming that the signal is a Sync On Green signal (i.e. that the sync signal is contained in the G signal of RGB), and this may result in an unstable image, depending on the video signal.

*4 1080i (50Hz) corresponds to a SMPTE274M signal. (Horizontal frequency is 28.125kHz)

Connecting Peripheral Equipment (Continued)

PC audio

PC(DIGITAL)INPUT

PC(ANALOG)INPUT

AUDIO

PC (digital) video

■ PC: Terminals for two kinds of PC video input signal are available. Input Select

PC (analog) video

Analog

Digital

Terminal type

D-Sub15-pin

DVI-D

VGA, SVGA, XGA, SXGA and others Appendix 1 In addition to ordinary Separate Sync (HD/VD) signals, the system is also compatible with Composite Sync (Csync) and Sync On Green. (*1) (*2)

VGA, SVGA, XGA, SXGA and others Appendix 1

Compatible signals

No matter which video signal is selected, the system uses the signal input to the audio terminals for audio.

Related topic:

*1 Auto-detects Sync signal type. *2 Sync signal presence is detected in the order: Separate Sync → Composite Sync → Sync On

Green. If for some reason neither Separate Sync nor Composite Sync is input, the system will operate assuming that the signal is a Sync On Green signal (i.e. that the sync signal is contained in the G signal of RGB), and this may result in an unstable image, depending on the video signal.

16

Connecting Peripheral Equipment (Continued)

VIDEO OUTPUT

VIDEO

OUTPUT

Video

■ When INPUT2 is displayed, video from INPUT2 is output. Otherwise video from INPUT1 is output.

INPUT3/PC (ANALOG) OUTPUT

and Installation

Connection

INPUT 3 / PC (ANALOG) OUTPUT

■ When INPUT3 is displayed, video from INPUT3 is output. Otherwise PC (analog) video is output.

RS-232C INPUT/RS-232C OUTPUT

RS-232C INPUT

RS-232C OUTPUT

■ The RS-232C INPUT and RS-232C OUTPUT are used to control this monitor with a PC. To connect a single monitor to a PC, connect to the RS-232C INPUT terminal. To connect multiple monitors in a daisy chain for control by PC, use the RS-232C OUTPUT terminal.

Connecting External Speakers

"Rear view

Speaker compatibility:

» Be sure to use external speakers with an

impedance of 8 ohm and a rated input of at least 10W.

To external speaker (right)

"SPEAKER R terminal

Make sure to connect the speaker jack and cable polarity

To external speaker (left)

"SPEAKER L terminal

How to connect the speaker cables

Pull up the lid.

Insert the edge

of the cable.

Put the lid back

down.

(±, —)

properly.

■ The speaker jacks have plus ± and minus — polarity. Plus is red and minus is black.

The cables are also divided into plus and minus. When connecting the left/right speakers, be sure to connect the plus/minus jacks with the correct cables.

18

NOTE:

» You can output audio from the built-in monitor speaker on the back of the monitor. See “Monitor Speaker Output”

on page 57 for details.

Connecting the AC Cord

Caution

"Rear view

'AC input terminal

(plug in here)

Be sure to turn the main POWER off when connecting the cord.

Plug (to the AC

input terminal)

Plug (to power outlet)

AC cord 9 ft.10-

/8″ (3 m)

and Installation

Connection

Power outlet

Attaching portion

Screw

Cable clamp

Fastening the AC cord

1. Plug the AC cord into the AC input terminal on the back of the monitor.

» Align the shape of the plug and the connector, and

insert all the way in.

2. Attach the supplied cable clamp to the AC cord.

3. Align the hole of the cable clamp with the screw hole on the monitor, and fasten the cable clamp screw.

4. Plug the AC cord into the AC power outlet.

» Be sure to plug all the way into the socket.

» When connecting the power cord to the main unit, always

NOTE:

use the cable clamp to keep the power cord from coming loose.

Connecting Multiple Monitors

■ Multiple monitors can be connected in a daisy chain using the input/output terminals for video/audio signals.

Connection examples for video only

Example: 1

Example: 2

OUTPUT

2 1

Video cable

To video output terminal

External device

INPUT 1VIDEO

Video cable

2 1

INPUT 1

shows the signal flow.

20

PC (ANALOG) INPUT

RGB cable

To video output terminal

INPUT 3/PC (ANALOG) OUTPUT

RGB cable

PC(ANALOG) INPUT

shows the signal flow.

Connecting Multiple Monitors (Continued)

Connection examples for video and audio

Use by selecting “INPUT2 Select” and setting INPUT2 to “Output”.

Example: 1

INPUT 2 (INPUT/ OUTPUT)

VIDEO OUTPUT

(Red: audio right)

(

White: audio left)

2 1

INPUT 1

(Red: audio right)

(

White: audio left)

2 1

INPUT 1

(Red: audio right)

(

White: audio left)

and Installation

Connection

Example: 2

INPUT 2 (INPUT/ OUTPUT)

Video cable

To video output terminal

External device

2 1

Audio cable

To audio output terminal

Video cable

Audio cable

INPUT 1

2 1

shows the signal flow.

INPUT 1

(Red: audio right)

White:

( audio left)

(Yellow: video)

Video cable

To video output terminal

External device

White:

(

(Red:

audio

left)

right)

Audio cable

To audio output terminal

Video/audio cable

RCA-BNC conversion adapter

(Yellow: video)

(Red: audio right)

(

White: audio left)

shows the signal flow.

Connecting Multiple Monitors (Continued)

Use by selecting “INPUT2 Select” and setting INPUT2 to “Output”.

Example: 3

(Red: audio right)

2 1

(

White: audio left)

INPUT 2 (INPUT/ OUTPUT)

RGB cable

To video output terminal

PC (ANALOG) INPUT

PC audio cable

To PC audio output terminal

INPUT 3/PC (ANALOG) OUTPUT

RGB cable

shows the signal flow.

PC(ANALOG) INPUT

■ Monitors can be externally controlled using the RS-232C interface (COM port) of a PC, and, in this case too, multiple monitors can be connected in a daisy chain. By assigning each monitor an ID number (see page 56), you can perform input switching, adjustment and status monitoring of individual monitors.

"First monitor "Second monitor

"PC

RS-232C cross cable

To COM port

To RS-232C INPUT terminal

To RS-232C OUTPUT terminal

To RS-232C INPUT terminal

To RS-232C OUTPUT terminal

Related topic:

22

PC Operation

Mounting Options

■ Please use an optional table stand or wall-mount bracket designed specifically for this product.

Mounting precautions

This monitor is equipped with a temporary stand when shipped from the factory. Please note this stand is for temporary use only until the monitor is properly mounted. Be sure to use a special-purpose AN-37ST1 table stand or AN-37AG1 wall-mount bracket (both optional).

Mounting the table stand (AN-37ST1) (LC-M3700)

See the table stand instructions for details.

M5 screws 25 mm length (5 screws)

Stand base

Stand hinge

1. Assemble the table stand.

● Align the 5 screw holes of the stand base with the corresponding screw holes of the stand hinge. Then attach the stand base to the stand hinge using the supplied 5 screws (M5 25 mm length).

and Installation

Connection

Terminal cover

Temporary stand

Wide LCD Monitor

Table

Soft cloth, etc.

M5 screws 12 mm length (4 screws)

2. Detach the temporary stand.

●Place the monitor (face down) on a table, etc. covered by a thick, soft cloth for LCD panel protection.

●Position the monitor near the edge of the table so that the temporary stand does not hit the table, then remove the terminal cover.

●Unfasten the 4 screws used to secure the temporary stand in place, then remove the stand.

3. Attach the table stand assembled in step 1 to the back of the monitor using the supplied 4 screws (M5 12 mm length).

●After installation, close the terminal cover, and

adjust the monitor to a suitable angle. (Tilting range: up to 4˚ forward and 6˚ backward. Rotating range: up to 10˚ clockwise and anticlockwise.)

Table stand

Mounting Options (Continued)

AN-37AG1 Wall-Mount Bracket Installation

See the bracket instructions for details.

Mounting precautions

for mounting work. The customer should never perform any of this work himself or herself. Our company will bear no responsibility for accidents or injuries caused by improper mounting or handling.

Installing wall-mount bracket

1. Determine the location where the base bracket will be installed.

● Take a washer about the size of a coin with a string and align it perpendicular to the base bracket.

● Use a pencil, etc., to mark the two screw hole locations.

Special techniques are required to mount this monitor, so be sure to rely on a specialist

Cellophane tape, etc.

Wall-mount bracket unit installation hooks

Perpendicular reference line

shaped screw holes

Use a pencil, etc., to mark the screw hole position on the wall behind the bracket.

Display screen center position

Use this as a reference for the display height position.

Marking A

Align horizontally and vertically until

Base bracket

the string lies on top of the vertical reference line.

2. Loosely screw in the screws.

● Temporarily remove the base bracket from the wall and loosely screw in 2 off-the-shelf screws in the screw hole positions marked on the wall. At this time, the screw heads should extend several millimeters above the wall so that the base bracket can be hung on the screw heads.

● Hang the base bracket on the installed screws, check to make sure the bracket is not sagging to the left or right, and then firmly tighten the screws. Use off-the-shelf screws to secure the remaining screw holes (14 to 18 screws).

Min. 4mm

WallWall

Use the weight with the string used in Step 1 to make sure the bracket is perpendicular.

Base bracket

24

Mounting Options (Continued)

Setting the angle of the wall-mount bracket

■ The wall-mount bracket is assembled for perpendicular installation, so to use it for tilted installation, please follow the procedure below to set it at the installation angle.

Setting the installation angle.

1 Remove the 2 vertical installation screws. These

screws are used when setting the angle in step

2 Assemble the wall-mount bracket as desired as

shown in the figure. (Figure shows a 20˚ angle.)

3 Use the screws removed in Step 1 (M6 15 mm

length × 2 screws) and the included screws M6 15 mm length × 2 screws to loosely fasten the angle-setup bracket with 4 screws. Firmly tighten these 4 screws after the angle-setup

Wall-mount bracket

bracket position has been determined.

Caution

• When setting the angle of the wall-mount bracket, be careful not to pinch your fingers, etc.

and Installation

Connection

Installation angle:

Screws M6 15mm length (4 screws)

LC-M3700 (Horizontal mount) 0° to 20°

LC-M3710 (Vertical mount) 0°

Install so that the angle-setup bracket spacers are facing inward.

Wall-mount bracket

Attaching wall-mount bracket to the monitor

1. Detach the temporary stand.

Terminal cover

Screws (4 locations)

Wide LCD Monitor

As the screw hole numbers become larger (5, 10,15, 20), the Wide LCD Monitor will be tipped farther forward.

5˚

10˚

15˚

20˚

Angle setup bracket (2 units)

●Place the monitor (face down) on a table, etc. covered by a thick, soft cloth for LCD panel protection.

●Position the monitor near the edge of the table so that the temporary stand does not hit the table, then remove the terminal cover.

●Unfasten the 4 screws used to secure the temporary stand in place.

Temporary stand

Table

Soft cloth, etc.

Mounting Options (Continued)

Upper side

Marking A

Wall-mount bracket

Marking A

Attaching wall-mount bracket to LC-M3700 (horizontal mount)

M6 30mm length

2. Attach the wall-mount bracket (with the angle set) to the back of the Wide LCD Monitor.

●Make sure all cables and cords are connected

and bundled (see page 29).

●Attach the terminal cover to the back of the

monitor and align the wall-mount screw holes (Marking A: 4 locations) with the holes (4 locations) on the back of the Wide LCD Monitor.

●Use the supplied M6 30 mm length screws (4

screws) to securely fasten the wall-mount bracket in place.

Attaching wall-mount bracket to LC-M3710 (vertical mount)

M6 30mm length

Upper side

Mounting the Wide LCD Monitor

Caution

Install the wall-mount bracket attached to the Wide LCD Monitor to the base bracket.

Å Hang the square holes ( ) of the wall-mount bracket on the hooks (page 24) of the base bracket. ı Tighten the wall-mount bracket and base bracket screws. (Be sure to do this.)

Åı

Wide LCD

Monitor

• Be sure to use 2 people when installing the Wide LCD Monitor to the base bracket.

• Be sure to perform Steps Å and ı below. Just performing Step Å could result in the display falling off, which is very

dangerous.

Make sure the hooks are engaged.

Wall

Tighten from the bottom.

Base bracket

M5 screws 8mm length (2 screws)

26

Outside dimensional drawings

»With table stand attached

[290]

11-

35-25/32 [909]

31-

/64 [810]

37-23/64 [949]

Mounting Options (Continued)

Unit: inch [mm]

18-43/64 [474.5]

[58.8]

[82.1]

[99.5]

[108.4]

1-13/

[36]

and Installation

Connection

[66.1]

[462.8]

18-

14-9/

32-11/32 [821.6]

[12.3]

3-28/

[173.8]

[370]

[98.4]

10-7/16 [265]

/8 [200]

[173.8]6-27/

[65]

4-1/8 [105]

[13]

1-29/64[37]

with the door opened

[572]

22-

[642]

25-

[356]

[12]

14-

[66.1]

[290]

11-

/32 [18.5]

[6.5]

[24]

6-1/ [154]

[8]

3-11/

2-3/

[55.5]

[80.5]

7-7/8 [200]

[223]

[200]

[170]

1-31/32 [50]

[115]

[142]

[72.5]

6-19/

/32 [120]

[160]

[155]1-

[38.5]

13-7/32 [335.8]7-13/32 [188.3]

Mounting Options (Continued)

Outside dimensional drawings

»With wall-mount bracket attached

[30]

5-3/32 [129.5]

6-4/3 [171.7782]

8-3/8 [212.9]

9-15/16 [252.5]

Unit: inch [mm]

11-7/16 [290.4]

/64 [572]

22-

/32 [129.5]

(0°)

5°

4-13/16 [122.3]

(5°)

4-1/2 [114.2]

(10°)

5-3/

[129.5]

10°

15°

4-5/32 [105.5]

(15°)

(20°)

LC-M3700 (Horizontal mount)

Panel center

[30]

20°

3-25/32 [96]

Wall-mount bracket center

/32 [15]

28

[949]

37-

5-3/

(0°)

[129.5]

LC-M3710 (Vertical mount)

Bundling Cables

Cable binder

To external devices

Bundle of cables

Wrap the cable binder around the bundle of cables.

Put the thinner end of cable binder through the hole as shown, and tighten appropriately.

"With terminal cover closed

■ Cables and cords connected to the back of the monitor can be bundled using the supplied cable clamp and cable binders. This will prevent stray or disorganized cables at the back of the monitor.

"Rear view

To external devices

Cable binder

and Installation

Connection

Wrap the cable binder around the bundle of cables.

Bundle of cables

Put the thinner end of cable binder through the hole as shown, and tighten appropriately.

How to use the supplied terminal cover mounting screws and flat washers

» Use terminal cover mounting screws to firmly fix the terminal cover if difficult to close after

bundling the cables.

Turning on Power

■ Before turning on POWER, make sure that peripherals, external speakers, and the AC cord are connected properly.

■ There are two power supply switches: POWER (main power supply) and STANDBY/ON.

Main POWER switch

"Rear view

"POWER (main) switch

"Front view

STANDBY/ON indicator

PRESS POWER (MAIN) ON THE BACK OF THE MONITOR.

» The STANDBY/ON indicator at the lower-

right corner of LCD panel lights up green.

■ Please note that STANDBY/ON will not turn power on if the main POWER is not switched ON.

STANDBY/ON

"Remote control unit

STANDBY/ON

INPUT

RETURN

ENTER

ENLARGE

VOL

WIDE

PRESS STANDBY/ON TO TURN THE POWER ON/OFF.

Power “On”: STANDBY/ON indicator lights up green. Power “Off”: STANDBY/ON indicator lights up red.

30

Remote Control Unit

■ Generally the monitor is operated using the remote control unit once main POWER on the back of the monitor has been turned on.

INPUT (Input selection)

Press INPUT to display the input selection screen. Press INPUT or use

'/"

(Cursor control) to select the input mode.

» In INPUT1 or PC mode, the video selected in “Input Select”

(page 54) is displayed on the screen.

» INPUT2 can be selected only when it has been set to “Input” in

“INPUT2 Select” (see page 56).

STANDBY/ON

INPUT

RETURN

ENTER

ENLARGE

LCD MONITOR

VOL

WIDE

INPUT1

INPUT3 PCINPUT2

VOL (Volume adjustment)

Press to increase the volume, and to decrease the volume. Sound is muted when volume is set to “0”. Each input terminal has its own volume output setting.

ENLARGE

The display toggles as shown below, based on the setting on the menu screen.

Off 2 × 23 × 3

Enlarge

Basic Operation

WIDE (Screen size selection)

Press WIDE to display the “Wide Mode” menu screen. Press WIDE or use The screen sizes which can be selected vary depending on the type of video signal.

'/"

57 62

(Cursor control) to select the screen size.

Menu Items

■ Menus can be displayed on the screen to enable video and audio adjustment, and setting of various functions, using the remote control. For details refer to the pages where each topic is explained.

Menu option selection

Buttons used in menu operation

STANDBY/ON

» Displays and turns off the menu screen.

INPUT

RETURN

ENLARGE

LCD MONITOR

ENTER

VOL

WIDE

UP/DOWN/LEFT/RIGHT (Cursor control)

» '/"/\ / |: Selects a desired item on the screen. » \ / |: Adjusts a selected item.

Pressing increases a numerical value.

Pressing decreases a numerical value.

ENTER

» Continues to next step. » Determines the selected item.

RETURN

» Returns to the previous menu screen.

Example of menu operation: Adjusting “Position” in “Setup”.

Press menu screen displays.

and the

Press (or ) to select “Setup”.

123

32

MENU [Picture]

Contrast

Black level

Color

Tint

Sharpness

Advanced

Reset

NOTE:

Picture

Audio Power control

[30] 0

[ 0] –30

+40

+30

+10

» Due to the type of signal and its frequency, the items in the menu screen appear differently.

Power control

Setup Option

Control Lock

Input Select

Position

Picture Flip

Language

Input 2 Select

ID No. Setting

Enlarge

Panel Protection Cover

[Normal]

[English]

[Input]

[Detached]

[AV]

[Off]

Press (or ) to select “Position”, and

then press

Power control

[—]

∫ The position menu screen is

displayed.

ENTER

Setup Option

Control Lock

Input Select

Position

Picture Flip

Language

Input 2 Select

ID No. Setting

Enlarge

Panel Protection Cover

[Normal]

[English]

[Input]

[Detached]

[AV]

[Off]

[—]

Menu screen explanation

"Menu screen example (partial)

Power control Setup Option

Control Lock

Input Select

Position

Picture Flip

Language

Input 2 Select

ID No. Setting

Enlarge

Panel Protection Cover

Operation guide

MENU [Setup···Picture Flip]

Set Picture Direction

[Normal]

[English]

[Input]

[Off]

[Detached]

[AV]

[—]

Menu Items (Continued)

Item displayed in yellow

» This indicates item currently selected. » Press ENTER to go to the adjustment screen for

this item.



Item in brackets

» This shows the current setting for the item.

Items displayed in white

» This indicates that an item can be selected.

Item displayed with gray characters

» These items cannot be selected.

∗ There are various reasons why items cannot be

selected, but the main reasons are as follows:

1. There is no signal.

2. The function is not compatible with the current input signal.

Most picture adjustment options cannot be

selected in the following states:

1. When “Underscan” is selected in “Wide Mode”.

2. With a PC (digital) signal.

Basic Operation

Normal

Mirror

Upside Down

Rotate

RETURN MENU

: Select/ : Back : Exit

This shows the remote control buttons which can be used with the currently displayed screen, and their functions.

» Operate by following this operation guide.

Menu screen duration

» The menu screen will revert to the normal screen if there is no operation for 1 minute while the menu

screen is displayed.

Language setting

» The On-Screen Display language can be set to Japanese, English, German, French or Spanish.

See page 36 for details.

» Menu options differ between the AV and PC modes, but operating procedures are the same.

NOTE:

» The menu item illustrations in this operation manual are for explanation purposes (some are enlarged; others

cropped) and may vary slightly from the actual displays.

Menu Items (Continued)

PC (analog) input mode menu items

INPUT3 : RGB PC : Analog PC : Digital

For a table of adjustment ranges for each menu item, please see Appendix3 on page 70.

Picture

Audio

Power control

Setup

Option

Control Lock

Input Select

Input Signal

Auto Sync.

Fine Sync.

Picture Flip

Language

Contrast/Black Level

Advanced

C.M.S. (H)/(S)/(V)

Red/Green/Blue

Treble/Bass/Balance

Brightness

Power Management

Lock Item

Menu Display/Remote/Buttons/Power/

RS-232C

PIN/PIN Clear

Start Now/When Connected

NOTE:

INPUT2 Select

ID No. Setting

Enlarge

Panel Protection Cover

» Due to the type of signal and its frequency, some items are not selectable and grayed out. » “C.M.S.” is the only picture adjustment item which can be used with PC (digital) signals. » “Fine Sync.” (position adjustment etc.) cannot be used with PC (digital) signals.

H-Pos./V-Pos./Clock/Phase

Wide Mode/DNR/Quick Shoot/

Monitor Speaker Output

34

AV input mode menu items

Menu Items (Continued)

INPUT1: AV, Y/C INPUT2: INPUT3: COMPONENT

Picture

Audio

Power control

Setup

Option

For a table of adjustment ranges for each menu item, please see Appendix3 on page 71.

Contrast/Black Level/Color/Tint/

Sharpness/

Advanced

C.M.S. (H)/(S)/(V) /Color Temp/Black/

3D-Y/C / Monochrome/Film Mode/

I/P Setting

Treble/Bass/Balance

Brightness

Power Management

Basic Operation

NOTE:

Control Lock

Input Select

Position

Picture Flip

Language

INPUT2 Select

ID No. Setting

Enlarge

Panel Protection Cover

»“INPUT2 Select” is not displayed when the input mode is set to “INPUT2”. » Due to the type of signal and its frequency, some items are not selectable and grayed out. » If “Underscan” has been selected in “Wide Mode”, most picture adjustment items cannot be used (except for

some settings in “Advanced”).

Lock Item

Menu Display/Remote/Buttons/Power/

RS-232C

PIN/PIN Clear

H-Pos./V-Pos.

Wide Mode/Color System/

DNR/Quick Shoot/

Monitor Speaker Output

Menu Items (Continued)

Language setting

■ The On-Screen Display language can be set to Japanese, English, German, French or Spanish.

STANDBY/ON

INPUT

RETURN

ENLARGE

LCD MONITOR

VOL

ENTER

WIDE

1 Press

to display the menu

screen.

2 Press

or to select

“Setup”.

MENU [Setup]

Picture Audio Power control Setup Option

Control Lock

Input Select

Position

Picture Flip

Language

Input 2 Select

ID No. Setting

Enlarge

Panel Protection Cover

Press or to select “Lan- guage”, then press

ENTER

Power control Setup Option

Control Lock

Input Select

Position

Picture Flip

Language

Input 2 Select

ID No.Setting

Enlarge

Panel Protection Cover

[AV]

[Normal]

[English]

[Input]

[—]

[Off]

[Detached]

[Normal]

[English]

[Input]

[Detached]

[AV]

[—]

[Off]

Press or to select desired language.

MENU [

MENU [Setup···Language]

:Select / :Back :Exit

Display language settings.

RETURN MENU

English

Deutsch

Français

Español

»The menu screen is now displayed in the

language selected.

Press

to return to normal

screen.

36

PC connection

PC Operation

1 One-to-one connection with a PC

.......

Basic operation

Connect with RS-232C cross cable between the PC COM port (RS-232C connector) and the RS232C INPUT terminal on the back of monitor.

"Rear view

To RS-232C INPUT terminal

2 Daisy chain connection from a single PC

RS-232C cross cable

.......

Advanced operation

To COM port

"PC

Connect with RS-232C cross cable between the PC COM port (RS-232C connector) and the RS232C INPUT terminal on the back of monitor. Next, connect RS-232C cross cable to the first monitor’s RS-232C OUTPUT terminal and to second monitor’s RS-232C INPUT terminal. Connect in the same way to the third and subsequent monitors. Up to about 20 monitors can be connected, depending on the length of RS-232C cables and installation environment.

"First monitor "Second monitor

Basic Operation

PC Operation

"PC

RS-232C cross cable

To COM port

To RS-232C INPUT terminal



To RS-232C OUTPUT terminal

To RS-232C INPUT terminal

To RS-232C OUTPUT terminal

Communication conditions

■ Set the RS-232C communication settings on the PC to match the monitor’s communication settings.

Baud rate: 9,600 bps

Data length: 8 bits

Parity bit: None

Stop bit: 1 bit

Flow control: None

PC Operation (Continued)

Communication procedure

Basic operation

When a command is sent from the PC to the monitor, the monitor operates according to the received command, and sends a response message to the PC.

C2 C3 C4 P1 P2 P3 P4 ↵

Carriage return code

Command field

(4 prescribed

alphanumerical

characters)

Parameter field

(4 character string

comprised of:

0-9, +, –, space, ?)

Example: VOLM0030

POWR

1 (“ ” indicates a space.)

* Be sure to input 4 characters for the parameter. Pad with spaces if necessary.

× VOLM30 䡩 VOLM 30( )(“ ” indicates a space, “ ” is the carriage return code

(0D

H, 0AH or 0DH).)

If a command has “R” listed for “Direction” in the “RS-232C Command table” on page 46, the current value can be returned by using “?” as the parameter.

Example: 1If an ID number has not been set:

VOLM???? ←From PC to monitor (current volume setting: ?) 30 ←From monitor to PC (current volume setting: 30)

2If an ID number has been assigned (For example, ID number = 001)

VOLM 30

001 ←Monitor to PC (“ ” indicates a space)

? ←PC to monitor (“ ” indicates a space)

■ When a command has been executed correctly

Carriage return code (0D

K ↵

■ When a command has not been executed correctly*

R R ↵

■ If execution of the command is taking some time

A I T ↵

■ If RS-232C is locked

Carriage return code (0D

, 0AH)

38

H, 0AH)

Carriage return code (0D

, 0AH)

Carriage return code (0D

H, 0AH)

K E DOC ↵

This is returned when execution of the command is finished.

* This is returned when there is no such command,

or when the command cannot be used in the current state of the monitor (i.e. video auto-adjustment with video display).

* If there is a bad connection between the PC and

monitor, or if communication has not been established, nothing is returned (not even ERR).

If a command takes some time to execute, WAIT may be returned as the return value. Wait for a moment, and OK or ERR will be returned. New commands cannot be received during this time, even if they are sent.

If RS-232C control has been locked with Control lock (see page 54), LOCKED is returned as the returned value.

PC Operation (Continued)

Advanced operation

■ This section explains commands for daisy chain connection. The basic communication procedure is the same as in the “Basic operation” section.

You can assign a unique ID number to each monitor (see page 56). This allows you to control a particular monitor in a daisy chain of monitors. Up to about 20 monitors can be connected, depending on the length of RS-232C cables and installation environment. You can assign ID numbers either from the menu screen (via remote control or the control buttons on the monitor) or from the PC using RS-232C cable.

[Example]

PC ID number: 1 ID number: 2 ID number: 3 ID number: 4

If monitors are connected as shown above, you can execute commands like “Set the volume of the monitor with ID 4 to 20”.

When controlling monitors linked in a daisy chain by designating ID numbers, you should basically avoid any duplication of ID numbers. If the same ID number is assigned to multiple monitors, only the monitor closest to the PC can be controlled with that ID number. If monitors are connected as shown below, only the monitor 1 can be accessed with ID number 2. Monitor 2 cannot be controlled using that ID number.

[Example]

PC ID number: 1 ID number: 2 ID number: 2 ID number: 3

① ②

ID numbers do not have to be assigned in ascending order starting from the PC. They can also be connected as shown below.

[Example]

PC Operation

PC ID number: 3 ID number: 2 ID number: 4 ID number: 1

Continued on the next page.

PC Operation (Continued)

The command examples shown on this page assume the following connection and ID number set up.

PC ID number: 1 ID number: 2 ID number: 3 ID number: 4

IDST······A monitor receiving this command sets its own ID number in the parameter field. Example: IDST0001

001 ←The ID number of this monitor is set to 1.

Note

After linking monitors, you can automatically assign ID numbers by using the IDST command with the Repeater control (see “Repeater control” on page 42).

[Example]

PC Set 1 Set 2 Set 3 Set 4

If you connect monitors as shown above, and use the command “IDST001+”, ID numbers will be set automatically, as shown below.

[Example]

PC ID number: 1 ID number: 2 ID number: 3 ID number: 4

IDST001+ ←ID setting command with repeater control WAIT OK

001 ←ID = “OK” response from ID number=1

002 ←ID = “OK” response from ID number=2

003 ←ID = “OK” response from ID number=3

004 ←ID = “OK” response from ID number=4 (End)

40

PC Operation (Continued)

IDSL······ The parameter of this command sets the ID number indicating the monitor subject to the

next command.

Example:

IDSL0002 ← The next command is for the monitor with ID number=2. WAIT ← Searching for monitor with ID number=2. OK

002 ← Found monitor with ID number=2 VOLM0030 ← Set volume of monitor with ID number=2 to 30 WAIT ← Processing OK

002 ← OK response from monitor with ID number=2 VOLM0020 ← Set volume to 20 OK

001 ← The volume of the monitor with ID number=1

(the one directly connected to the PC) is set to

20.

IDLK······ The parameter of this command sets the ID number indicating the monitor subject to all

subsequent commands.

Example:

IDLK0002 ← Following commands are for the monitor whose ID number is “2”. WAIT ← Searching for monitor with ID number=2. OK

002 ← Found monitor with ID number=2 VOLM0030 ← Set volume of monitor with ID number=2 to 30 WAIT ← Processing OK

002 VOLM0020 ← Set volume of monitor with ID number=2 to 20 WAIT OK

002 IDLK0000 ← Canceling ID number setting WAIT ← Canceling IDLK OK

002 ← Cancelation complete VOLM0010 OK

001 ← The volume of the monitor with ID number=1 (the one directly connected

to the PC) is set to 10.

The IDSL command is effective only once, for the immediately succeeding command.

The IDLK command remains effective until it is canceled, or power is shut off.

PC Operation

IDCK······ Provides screen display of the ID number currently assigned to a monitor, and the ID

number currently set for IDLK (if any).

Example:

(After executing IDLK0002) IDCK0000 ← (Parameter has no meaning) ID:001 IDLK:002 ← Returned response. The ID number is also displayed on the

monitor screen. IDCK000+ ← Repeater control WAIT ID:001 IDLK:002

(If a command is used with repeater control, ID designation using

IDSL or IDLK is canceled.) ID:002 IDLK:002 ID:003 IDLK:002 ID:004 IDLK:002

Continued on the next page.

PC Operation (Continued)

This system has a function to allow setting of multiple monitors connected in a daisy chain using a single command. This function is called repeater control. Up to about 20 monitors can be connected, depending on the length of RS-232C cables and installation environment. You can use Repeater control function without assigning ID numbers.

[Example]

PC Set 1 Set 2 Set 3 Set 4

If monitors are connected as shown above, you can execute a command like “Set all monitors’ input settings to INPUT”.

Repeater control is achieved by setting the FOURTH CHARACTER of the parameter to “+”.

Example: VOLM030+ ← Sets volume of all monitors to 30.

In repeater control, responses are returned by all the connected monitors.* If you want to determine that a value has been returned by a specific set, assign ID numbers to each monitor in advance. If no response is returned, this may be because the monitor has not received (or is still processing) the command, so it is possible that new commands may not be executed even if they are sent.

* If power is turned “OFF” using Repeater control, only the monitor closest to the PC returns a

response.

Example: (When 4 monitors are connected, and assigned ID numbers 1 through 4)

VOLM030+ WAIT OK

001

002

003

004 ← If 4 monitors are connected in a chain, reliable operation can be ensured

by sending a new command only after a reply has been returned by 4th (last) monitor.

Repeater control can also be used for reading settings.

42

NOTE:

Example:

VOLM???+ WAIT 10

001

002

003

004

» If repeater control is used during ID designation (IDSL, IDLK), the ID designation is canceled.

Volume settings for all monitors are returned.

■ Normal response

1Response when no ID number has been set.

Carriage return code (0D

H, 0AH)

K ↵

2Response when an ID number has been set.

Space (20H)

K SPC 0 0 1 ↵

ID number of

responding monitor

■ When a command has not been executed correctly*

1Response when no ID number has been set.

A response is returned when execution of the pertinent command is finished.

Carriage return code (0D

H, 0AH)

PC Operation (Continued)

Carriage return code (0D

H, 0AH)

R R ↵

2Response when an ID number has been set.

Space (20H)

R R SPC 0 0 1 ↵

Carriage return code (0D

H, 0AH)

ID number

* This is returned when there is no such command, or when the command cannot be used in the

current state of the monitor (i.e. video auto-adjustment with video display).

* If communication has not been established for reasons like a bad connection with the monitor,

nothing is returned (not even ERR).

* If no monitor has been assigned the designated ID number (e.g. if the command IDSL0002[X] is

issued, but no monitor with ID=002 is found), ERR

XXX[X] is returned.

(ID number at the furthest end)

[Example]

PC Set 1 Set 2 Set 3

PC Operation

In the above case IDSL0004

←Non-existent ID number WAIT ERR 003 ←Monitor with ID=3 at the furthest end returns ERR

Continued on the next page.

PC Operation (Continued)

■ If execution of the command is taking some time.

Carriage return code (0D

, 0AH)

If execution of a command takes some time, WAIT may be returned as the returned value. In this case, a value will be returned if you wait a while. During this time, new commands will not be

received, even if they are sent.

No ID number is attached to WAIT response.

• Cases where WAIT is returned

1. When repeater control is used

2. When an IDSL or IDLK command is used

3. When one of the following commands is used: RSET, INP1, INP2, INP3, INPC, INPS, ITGD, IAVD, IPCD, CLSY, ASNC, WIDE, EMAG, EPOS, PXSL, POWR

A I T ↵

■ When control via RS-232C is locked (to prevent use) using the Control lock function (see page 54).

Carriage return code (0D

, 0AH)

LOC K

↵

■ If a timeout occurs while waiting for a command

Carriage return code (0D

, 0AH)

↵

I M E O U

■ If a timeout occurs while waiting for a command (when the monitor waiting for the command is assigned an ID number = 001 in the following example)

Carriage return code (0D

, 0AH)

↵

TIM E O U

Space (20H)

SPC

0 0 1

■ If the current parameter is read out using "?" for the parameter (for numerical values etc.)

1Response when no ID number has been set.

<Example> VOLM????

2Response when an ID number has been set. (In the example below: ID=001)

<Example> VOLM????

10 001

44

PC Operation (Continued)

If the next command is sent in the interval before OK or ERR is returned, it will basically be ignored. (Exception: Forced end using ASNC command) Leave an interval of 100 ms between command response and transmission of the next command. You can use Repeater control function without assigning ID numbers.

VOLM0020 OK

Leave an interval of 100 ms

INP10000 OK

PC Operation

PC Operation (Continued)

RS-232C command table

Command : Command field

Direction : W When the “Parameter” is set in the parameter field (

command functions as described under “Control/Response Contents”.

R The returned value indicated under “Reply” can be obtained by setting

“????”, “___?” or “???+” (repeater control) in the parameter field (

Parameter :

Parameter

Reply : Response Returned value

∗A circle indicates commands which can be used in power standby mode.

Power control, etc.

CONTROL ITEM

POWER SETTING POWR W 0 Switches to standby.

CHANNEL DISPLAY DISP W − It displays channel display.

VOLUME VOLM WR 0 - 60 0 - 60

MUTE MUTE WR 0 0 OFF

SYNC CHECK SYNC W 0 It returns Yes/No.

CAUSE OF LAST STANDBY STCA W 0 Content initialization

CAUSE OF LAST ERROR ERCA WR 0 Content initialization

POWER CONTROL BRIGHTNESS VLMP WR ±8 ±8 Brightness

POWER PMNG WR 0 0 Off

LANGUAGE LANG WR 1 German

RESET RSET W 4 digits Input 4-digit PIN for parameter. It resets to factory preset value.

Command Direction Parameter Reply

1 Returns from standby.

R 0 Standby state

1 Normal status

2 Power standby state ("Mode2" in "Power Management").

11ON

1 It returns frequency.

1 Electrical standby due to some error condition (See cause of last error)

2 Invalid input has continued for a long time during PC display

3 It entered standby mode (PC mode: "Mode1" in "Power Management")

4 It entered standby mode (PC mode: "Mode2" in "Power Management")

6 It entered standby mode by the command from RS-232C.

0 No detectable error has occurred

1 Invalid input has continued for a long time during PC display

2 Internal bus error

3 Abnormal temperature

4 Board connection error

5 Lamp error

7 Electrical system error

8 Error in communication with microcomputer

1 1 Mode1

2 2 Mode2

2 French

4 Spanish

13 Japanese

14 English

RSE+ W 4 digits

No standby operation (except remote control and monitor button operation) after initialization

Input 4-digit PIN for parameter. It resets to factory preset value. For Repeater control

CONTROL/RESPONSE CONTENTS

), the

∗

46

PC Operation (Continued)

Input selection, etc.

INPUT SELECTION INPUT1 SELECTION INP1 W 0 Leaves input selection as is, and switches input to INPUT1

1 Sets input selection for INPUT1 to "AV"

2 Sets input selection for INPUT1 to "Y/C"

R 1 Input selection for INPUT1 is "AV"

2 Input selection for INPUT1 is "Y/C"

INPUT2 SELECTION INP2 W 0

1 Sets INPUT2 selection to "Input"

9 Sets INPUT2 selection to "Output"

R 1 INPUT2 selection is "Input"

INPUT3 SELECTION INP3 W 0 Leaves input selection as is, and switches input to INPUT3

1 Sets input selection for INPUT3 to "COMPONENT"

2 Sets input selection for INPUT3 to "RGB"

R 1 Input selection for INPUT3 is "COMPONENT"

PC INPUT SELECTION INPC W 0 Leaves input selection as is, and switches input to PC

1 Sets input selection for PC to "Analog"

2 Sets input selection for PC to "Digital"

INPC R 1 Input selection for PC is "Analog"

INPUT SELECT INPS W 0 Toggle operation

1 Switches input to video terminal of INPUT1.

2 Switches input to S-video terminal of INPUT1.

4 Switches input to video terminal of INPUT2. (Returns ERR if set to output.)

5 Switches input to INPUT3.

6 Switches input to D-sub pin 15 terminal of PC

7 Switches input to DVI terminal of PC

R 1 Displays video signal from INPUT1

ITGD W 0 Toggle operation

IAVD W 1 Switches input to INPUT1.

2 Switches input to INPUT2. (Return ERR if set to output.)

3 Switches input to INPUT3.

IPCD W

INPUT SOURCE DISPLAY IMOD R 1 INPUT1

−

Leaves input selection as is, and switches input to INPUT2. ERR if INPUT is set to output.

9 INPUT2 selection is "Output"

2 Input selection for INPUT3 is "RGB"

2 Input selection for PC is "Digital"

2 Displays S-terminal input video from INPUT1

4 Displays video from INPUT2

5 Displays INPUT3

6 Displays D-sub pin 15 terminal input video from PC

7 Displays DVI terminal input video from PC

Switches input to PC.

2 INPUT2

3 INPUT3

5PC

PC Operation

PC Operation (Continued)

Picture and audio adjustment, etc.

PICTURE ADJUSTMENT CONTRAST CONT WR 0 - 40 0 - 40

BLACK LEVEL BLVL WR ±30 ±30

COLOR COLR WR ±30 ±30

TINT TINT WR ±30 ±30

SHARPNESS SHRP WR ±10 ±10

RED REDG WR ±30 ±30

GREEN GREN WR ±30 ±30

BLUE BLUE WR ±30 ±30

C. M. S. (H) CMHR WR ±30 ±30 Red

CMHY WR ±30 ±30 Yellow

CMHG WR ±30 ±30 Green

CMHC WR ±30 ±30 Cyan

CMHB WR ±30 ±30 Blue

CMHM WR ±30 ±30 Magenta

C. M. S. (S) CMSR WR ±30 ±30 Red

CMSY WR ±30 ±30 Yellow

CMSG WR ±30 ±30 Green

CMSC WR ±30 ±30 Cyan

CMSB WR ±30 ±30 Blue

CMSM WR ±30 ±30 Magenta

C. M. S. (V) CMVR WR ±30 ±30 Red

CMVY WR ±30 ±30 Yellow

CMVG WR ±30 ±30 Green

CMVC WR ±30 ±30 Cyan

CMVB WR ±30 ±30 Blue

CMVM WR ±30 ±30 Magenta

COLOR TEMP CTMP WR 0 0 Low

1 1 Mid-Low

2 2 Mid

3 3 Mid-High

4 4 High

BLACK BLAK WR 0 0 Off

1 1 High

2 2 Low

3D-Y/C 3DYC WR 0 0 Standard

1 1 Fast

2 2 Slow

MONOCHROME MNCR WR 0 0 Off

11On

FILM MODE FILM WR 0 0 Off

11On

I/P SETTING IPST WR 0 0 Interlace

1 1 Progressive

AUDIO ADJUSTMENT TREBLE TRBL WR ±15 ±15

BASS BASS WR ±15 ±15

BALANCE BLNC WR ±30 ±30

COLOR SYSTEM CLSY W 0 AUTO

1 PAL

3 SECAM

4 NTSC358

5 NTSC443

R 0 AUTO

1 PAL

3 SECAM

4 NTSC358

5 NTSC443

48

PC Operation (Continued)

Picture and audio adjustment, etc. (continued)

POSITION/FINE SYNC. H-POSITION (AV) HPOS WR ±10 ±10 Video/S-video INPUT3 (Component)

H-POSITION (PC) WR 0 -180 0 - 180 INPUT3 (RGB)/PC (Analog)

V-POSITION (AV) VPOS WR ±20 ±20 Video/S-video INPUT3 (Component)

V-POSITION (PC) WR 0 - 99 0 - 99 INPUT3 (RGB)/PC (Analog)

CLOCK CLCK WR 0 - 180 0 - 180 Returns ERR in case of a video signal

PHASE PHSE WR 0 - 40 0 - 40 Returns ERR in case of a video signal

AUTO SYNC. ASNC W 0 Abort (after execution)

1 Start

ASAE WR 0 Setting cancel

1 Automatic execution when PC sync is input

WIDE MODE WIDE WR 0 0 Toggle operation

PICTURE FLIP PFLP WR 0 0 Normal

ENLARGE ENLARGE SETTING EMAG WR 0 0 Off

DNR DNR_ WR 0 0 Off

QUICK SHOOT QSDV WR 0 0 Off

MONITOR SPEAKER OUTPUT MOSP W R 0 0 Fixed

INPUT SIGNAL PXCK R

AV (Input1/Input2/Input3 (Component)

PC (Input3 (RGB)/PC) WIDE WR 0 0 Toggle operation

ENLARGED IMAGE EPOS WR 0 0 Enlarge Setting : Off

POSITION 0 0 Enlarge Setting : 2x2) Upper left

PXSL WR 0 0 V=400, 640x400

1 1 Normal

2 2 Full 14:9

3 3 Zoom 14:9

4 4 Panorama

5 5 Cinema 14:9

6 6 Cinema 16:9

7 7 Full

8 8 Underscan

1 1 Normal

2 2 Full

3 3 Cinema

44D by D

1 1 Mirror

2 2 Upside Down

3 3 Rotate

1 1 Enlarge Setting : 2x2) Upper right

2 2 Enlarge Setting : 2x2) Lower left

3 3 Enlarge Setting : 2x2) Lower right

0 0 Enlarge Setting : 3x3) Upper left

1 1 Enlarge Setting : 3x3) Upper middle

2 2 Enlarge Setting : 3x3) Upper right

3 3 Enlarge Setting : 3x3) Middle left

4 4 Enlarge Setting : 3x3) Center

5 5 Enlarge Setting : 3x3) Middle right

6 6 Enlarge Setting : 3x3) Lower left

7 7 Enlarge Setting : 3x3) Lower middle

8 8 Enlarge Setting : 3x3) Lower right

1 1 Low

2 2 High

11On

1 1 Variable

1 1 V=400, 720x400

0 0 V=480, 640x480

2 2 V=480, 848x480

3 3 V=480, 852x480

0 0 V=768, 1024x768

1 1 V=768, 1280x768

2 2 V=768, 1366x768

2×2

3×3

Returns current resolution in the form xxx,xxx.

−

PC Operation

PC Operation (Continued)

Other control options

ID NUMBER ID NO. SETTING IDST W 0 - 255 It sets the monitor's ID number.

R 0 - 255 It returns the monitor's ID number.

ID NO. SETTING (ONCE)

ID NO. SETTING (SUBSEQUENT)

ID CHECK IDCK W

CONTROL LOCK MENU DISPLAY LMNU WR Normal (Menu Display is available)

REMOTE CONTROL LREM W R Normal (Operational)

CONTROL BUTTONS LBTN WR Normal (Operational)

POWER LPOW WR Normal (Operational)

RS232C LCOM WR Normal (Operational)

PIN SET PIN PSET W 4 digits Sets PIN (Activates lock function)

INPUT PIN PINP W 4 digits Input of set PIN (Temporary unlock)

CLEAR PIN PCLR W 4 digits Initializes PIN

POWER-ON METHOD, ETC. MAX VOLUME MVOL W R 1 - 60 1 - 60 Maximum volume limit. Only displays volume in numbers when set to other than 60.

FIX VOLUME FVOL WR 0 0 Off

OSD SETTING ODSP WR 0 0 Normal

DISPLAY BOOT FINP W R 0 0 Normal

OPTION 1 1 Starts with INPUT1 + [AV] input selection

SOUND INPUT SELECT SNDS WR 0 0 Normal

PANEL PROTECTION COVER

IDSL W 1 - 255

0 Clears the ID number if one has been designated.

IDLK W 1 - 255

0 Clears the ID number if one has been designated.

−

1 1 Menu Display is not available.

1 1 Disabled

PSE+ W 4 digits Sets PIN: for repeater control

PIN+ W 4 digits Input of set PIN: for repeater control

PCL+ W 4 digits Initializes PIN: for repeater control

1 1 Fixes volume at a constant value

1 1 No OSD is displayed.

2 2 Starts with INPUT1 + [Y/C] input selection

4 4 Starts with INPUT2. Returns ERR if INPUT2 selection is "Output"

5 5 Starts with INPUT3.

6 6 Starts with PC + [Analog] input selection

7 7 Starts with PC + [Digital] input selection

11 11 Starts with INPUT1 + [AV] input selection, and remains fixed

12 12 Starts with INPUT1 + [Y/C] input selection, and remains fixed

14 14

15 15 Starts with INPUT3, and remains fixed

16 16 Starts with PC + [Analog] input selection, and remains fixed

17 17 Starts with PC + [Digital] input selection, and remains fixed

1 1 Uses INPUT1 audio as fixed source

2 2 Uses INPUT2 audio as fixed source

COVR WR 0 0 Detached

1 1 Attached

Sets a monitor ID number. This ID number is only effective for the command immediately after this command.

Sets a monitor ID number. This ID number is effective for the next and all subsequent commands after this command.

Displays selected ID number and the monitor's own ID number on the screen.

Maximum volume limit. Only displays volume in numbers when set to other than 60.

Starts with INPUT2, and remains fixed. Returns ERR if INPUT2 selection is "Output".

50

Picture

Contrast

Adjustable range 0 - 40 Default 30 + direction For more contrast – direction For less contrast

Black Level

Adjustable range –30 - +30 Default 0 + direction Brightens entire video signal – direction Darkens entire video signal

Color (Video/S-video/COMPONENT)

Adjustable range –30 - +30 Default 0 + direction For more color intensity – direction Decreases color intensity (Monochrome at “0”)

Tint (Video/S-video/COMPONENT)

Adjustable range –30 - +30 Default 0 + direction Changes skin tone closer to green – direction Changes skin tone closer to magenta

Sharpness (Video/S-video/COMPONENT)

Adjustable range –10 - +10 Default 0 + direction For more sharpness – direction For less sharpness

Settings and Adjustments

PC Operation

Advanced: C. M. S. (H)

Function Six-color hue adjustments Adjustable range –30 - +30 (Red/Yellow/Green/Cyan/Blue/Magenta) Default 0 + direction Move selected color hue clockwise – direction Move selected color hue counter-clockwise

Advanced: C. M. S. (S)

Function Six-color saturation adjustments Adjustable range –30 - +30 (Red/Yellow/Green/Cyan/Blue/Magenta) Default 0 + direction Increases saturation of the selected color – direction Decreases saturation of the selected color

Advanced: C. M. S. (V)

Function Six-color image value adjustments Adjustable range –30 - +30 (Red/Yellow/Green/Cyan/Blue/Magenta) Default 0 + direction Increases brightness of the selected image value – direction Decreases brightness of the selected image value

Adjustments

Settings and

Settings and Adjustments (Continued)

Advanced: Color Temp (Video/S-video/INPUT 3 COMPONENT)

Adjustable range High, Mid-High, Mid, Mid-Low, Low Default Mid Upward Entire image bluish tone (color temperature increases) Downward Entire image reddish tone (color temperature decreases)

Advanced: Black (Video/S-video/INPUT 3 COMPONENT)

Adjustable range Off, High, Low Default Low Off No Adjustment High For high detail in black portions Low For low detail in black portions

Advanced: 3D-Y/C (Video)

Adjustable range Standard, Fast, Slow Default Standard Standard Normal adjustment [Sets characteristics for 3-dimensional Y/C separation to

standard setting.]

Fast For movie image [Sets characteristics for 3-dimensional Y/C separation to settings

appropriate for movies.]

Slow For still image [Sets characteristics for 3-dimensional Y/C separation to settings

appropriate for still pictures.]

Note: Effective only when displaying video source with color system NTSC 3.58

Advanced: Monochrome (Video/S-video/INPUT 3 COMPONENT)

Adjustable range On/Off Default Off On Displays video in monochrome. (“Tint” cannot be adjusted. The setting automatically

set to “Off” if “Color” is adjusted.)

Off Normal color

Advanced: Film mode (Video/S-video/INPUT 3 COMPONENT)

Adjustable range On/Off Default On On Automatically detects that the source signal is a video image at 24 frames/sec (DVDs

containing films etc.), and displays signal with high picture quality.

Off Does not automatically detect sources at 24 frames/sec. Note: Effective only for interlaced video (480i/576i/1080i)

Advanced: I/P Setting (Video/S-video/INPUT 3 COMPONENT)

Adjustable range Interlace/Progressive Default Progressive Interlace Displays interlaced signal with 2-dimensional interpolation Progressive Displays interlaced signal with 3-dimensional interpolation Note: Effective only for Video, S-video and COMPONENT 480i/576i image

Red (PC (analog)/INPUT3(RGB))

Adjustable range –30 - +30 Default 0 + direction Brightens red component – direction Darkens red component

52

Green (PC (analog)/INPUT3(RGB))

Adjustable range –30 - +30 Default 0 + direction Brightens green component – direction Darkens green component

Blue (PC (analog)/INPUT3(RGB))

Adjustable range –30 - +30 Default 0 + direction Brightens blue component – direction Darkens blue component

Audio

Treble

Adjustable range –15 - +15 Default 0 + direction For stronger treble – direction For weaker treble

Bass

Adjustable range –15 - +15 Default 0 + direction For stronger bass – direction For weaker bass

Settings and Adjustments (Continued)

Balance

Adjustable range Left 30 - Right 30 Default 0 (center value) Toward left Decrease audio from the right speaker Toward right Decrease audio from the left speaker

Power control

Brightness

Function Adjusts backlight brightness Adjustable range –8 - +8 Default +8 + direction Increases backlight brightness – direction Decreases backlight brightness

Power Management

Function With this setting, the monitor automatically switches to (or returns from) the power

standby mode, depending on the presence of a sync signal.

Adjustable range Off/Mode1/Mode2 Default Off Off No Power Management Mode1 Detects sync signal of currently displayed video signal, and enters power standby

mode if there is no sync signal for 8 minutes.

Mode2 D

etects sync signal of currently displayed video signal, and enters power standby

mode if there is no sync signal for 8 seconds. Restarts when sync signal is input again

Adjustments

Settings and

NOTE:

» The monitor may not work properly if the AC cord is unplugged and replugged when “Mode2” is selected in

“Power Management”. In this case simply press the STANDBY/ON button on the monitor or on the remote control.

Settings and Adjustments (Continued)

Setup

Control Lock: Lock Item (See page 58 for details.)

Function Adjustable range Lock/Unlock (“Menu Display”, “Remote”, “Buttons”, “Power” and “RS-232C”) Default Unlock (all items) Lock The pertinent function is disabled when a PIN is set (see page 58). Unlock The pertinent function can be used, even if a PIN is set.

Control Lock: PIN (See page 58 for details.)

Function Sets 4-digit PIN

After a PIN has been set, it becomes effective when the menu is closed. If a PIN is temporarily canceled (see page 58 for details), it remains canceled until the monitor enters standby mode or shuts down.

Control Lock: PIN Clear (See page 58 for details.)

Function Initializes set PIN. (Returns to state where no PIN has been input.)

Input Select

Function Selects video input terminal/type. Adjustable range INPUT1: AV / Y/C

INPUT3: COMPONENT/RGB PC: Analog/Digital

Default INPUT1: AV

INPUT3: COMPONENT PC: Analog

Input Signal (INPUT3 (RGB) /(PC (analog))

Function Manually selects input resolution. Adjustable range (Analog 400 vertical lines) 640 × 400/720 × 400

(Analog 480 vertical lines) 640 × 480/848 × 480/852 × 480 (Analog 768 vertical lines) 1024 × 768/1280 × 768/1366 × 768 (Digital 480 vertical lines) 640 × 480/480p

Default (Analog 400 vertical lines) 640 × 400

(Analog 480 vertical lines) 640 × 480 (Analog 768 vertical lines) 1024 × 768 (Digital 480 vertical lines) 640 × 480

Auto Sync.: When Connected (INPUT3 (RGB) /(PC (analog))

Function Automatically optimizes position, phase and clock when applicable video is input. Adjustable range Yes/No Default No Note: You can quickly achieve high-picture quality results by using a signal suited to the

adjustment as the video signal used for adjustment. Conversely, performing adjustment with a signal unsuited for adjustment may cause adjustment to fail, or make it impossible to achieve good results even if it succeeds. Example of the ideal signal for use in adjustment: An image with full size and resolution, and a vertical stripe signal which inverts between black and white at each pixel. *Signals suitable for Auto Sync. •Detailed still image with well-defined contrast

•Image with high luminosity at edges

*Signals not suited for Auto Sync. •Image with low contrast • Moving picture

•Image with low luminosity at edges

54

Settings and Adjustments (Continued)

Auto Sync.: Start Now

Function If “Yes” is selected and the ENTER button is pressed when applicable video is input,

the system automatically optimizes position, phase and clock using the video signal which is currently being input.

Adjustable range Yes/No (“No” is always the default value)

Position: H-pos. (Video/S-video/INPUT 3 COMPONENT)

Adjustable range –10 - +10 Default 0 + direction Image shifts right. – direction Image shifts left.

Position: V-pos. (Video/S-video/INPUT 3 COMPONENT)

Adjustable range –20 - +20 Default 0

+ direction Image shifts up.

– direction Image shifts down.

Fine Sync.: H-pos. (INPUT3 (RGB)/(PC (analog))

Adjustable range 0 - 180 Default 0 + direction Image shifts right. – direction Image shifts left. Note: No position adjustment is available when PC (digital) signal is received.

Fine Sync.: V-pos. (INPUT3 (RGB) /(PC (analog))

Adjustable range 0 - 99 Default (Varies depending on video frequency) + direction Image shifts up. – direction Image shifts down. Note: No position adjustment is available when PC (digital) signal is received.

Fine Sync.: Clock (INPUT3 (RGB) /(PC (analog))

Function Adjusts frequency for sampling clock for applicable video.

Adjust when there is flickering in the form of vertical stripes.

Adjustable range 0 - 180 Default 90 + direction Clock frequency increases – direction Clock frequency decreases Note: No clock frequency adjustment is available when PC (digital) signal is received.

Fine Sync.: Phase (INPUT3 (RGB) /(PC (analog))

Function Adjusts phase of sampling clock for applicable video.

Useful when small characters appear with low contrast and/or there are flickers at corners.

Adjustable range 0 - 40 Default 20 + direction Advances clock phase – direction Delays clock phase Note: There is no clock phase adjustment for PC (digital) signals.

Adjustments

Settings and

Settings and Adjustments (Continued)

Picture Flip Adjustable range Normal/Mirror/Upside Down/Rotate Default Normal Normal Normal image Mirror Mirror image Upside Down Upside down image Rotate Rotated image

Language

Function Selects display language setting. Adjustable range Japanese, English, German, French, Spanish Default English

INPUT2 Select

Function Selects INPUT2 terminal use. Adjustable range Input/Output Default Input Input Using as Input Output Using as Output Note: (This setting cannot be switched when INPUT2 is currently being displayed.)

ID No. Setting

Function Assigns ID numbers to monitors connected in a daisy chain (see page 37), using

RS-232C cables.

Adjustable range 0 - 255 Default 0 Note: The numbers 1 to 255 are available for ID numbers.

(If “0” is set, the system regards this as the state where no ID number is set.) Although numbers up to 255 can be used for monitor IDs, the number of connectable monitors varies depending on the length of RS-232C cables and the installation environment. Use \/| to move between digits, and '/" to raise or lower digit values.

Enlarge: (see page 61 for details.)

Function Sets the image enlargement ratio, and the part of the original image to be enlarged. Adjustable range Off/2 × 2/3 × 3 Default Off ↓(After adjustment) Adjustable range (When set to “2 × 2”) 1 - 4 Default (When set to “2 × 2”) 1 Adjustable range (When set to “3 × 3”) 1 - 9 Default (When set to “3 × 3”) 1

Panel Protection Cover

Function Setting for panel protection cover. Be sure to set this item when using the cover. Adjustable range Attached/Detached Default Detached Note: Set to “Attached” when using the optional panel protection cover (commercially

available in the future).

56

Settings and Adjustments (Continued)

Option

Wide Mode (Video/S-video/INPUT 3 COMPONENT) (see page 63 for details.)

Adjustable range Default Panorama Note: Available when receiving a 480i, 576i, 480p or 576p image.

Wide Mode (INPUT 3 COMPONENT)

Adjustable range Full, Underscan Default Full Note: Available when receiving 1080i or 720p image

Wide Mode (INPUT3 (RGB)/PC (analog/digital)) (see page 62 for details.)

Adjustable range Normal, Full, Cinema and Dot by Dot Default Normal

Color System (Video/S-video)

Function Selects color system for Video and S-video image.

Adjustable range Auto, PAL, SECAM, NTSC 3.58, NTSC 4.43 Default Auto

Normal, Full 14:9, Zoom 14:9, Panorama, Cinema 14:9, Cinema 16:9, Full and Underscan

“Auto” (auto-detection of the color system) is the factory preset value. If normal discrimination cannot be achieved with the automatic setting, select the optimal color system manually.

DNR

Function Reduces picture noise. Adjustable range Off/High/Low Default Low Off This feature is inactive. High Applies stronger noise reduction Low Applies weaker noise reduction

Quick Shoot

Adjustable range On/Off Default On On Improves the response of Liquid Crystal Panel when viewing fast-moving images.

Monitor Speaker Output

Function Selects whether to use built-in monitor speaker. Adjustable range On/Off Default Off On Outputs sound from built-in monitor speaker Off Does not output sound from built-in monitor speaker

Adjustments

Settings and

Settings and Adjustments (Continued)

Detailed explanation

Control lock

Overview

This monitor is equipped with a control lock function to prevent third parties from changing the operating state. Locked functions cannot be used unless a PIN is input. PINs can be freely set by the user. The following types of operation can be locked.

» Menu Display

When locked, MENU buttons on the remote control and monitor are disabled.

» Remote Control

When enabled buttons on the remote control except STANDBY/ON are locked.

» Monitor Buttons

When enabled monitor buttons except STANDBY/ON are locked.

» Power

When locked, the STANDBY/ON button on the remote control and the monitor cannot perform switching from the operating state to the standby state. It can however, perform switching from the standby state to the operating state.

» RS-232C

When enabled operation using RS-232C is locked.

Lock state and temporary unlock (Except for RS-232C)

When some functions are locked, you will be prompted to enter PIN if you attempt to use the function. If you enter the correct PIN, the locks on all locked functions are temporarily unlocked, so you can use the functions. Functions which have been temporarily unlocked are locked again under the following conditions.

• The monitor entered standby mode. • Main POWER was turned off.

• PIN was changed. • Lock Items were modified.

Even if functions are temporarily unlocked, the system will ask for a PIN if you try to enter “Control Lock” from the “Setup” menu. This is to prevent the PIN from being modified while it is temporarily unlocked.

Permanent unlocking (Except for RS-232C)

1) Select “Control Lock” from “Setup” in the menu screen.

2) Select “PIN Clear”, then “Yes” and press ENTER.

Lock state and temporary unlock (RS-232C)

If RS-232C is locked and you sent an RS-232C command, LOCKED will come back as the returned value. Only the following commands will work in this state.

» PINPxxxx (“xxxx” is the current PIN.)

Temporarily unlocks the current lock. Functions which have been temporarily unlocked are locked again under the following conditions.

• The monitor entered standby mode. • Main POWER was turned off.

• PIN was changed. • Lock Items were modified.

58

» PIN+xxxx (“xxxx” is the current PIN.)

This command temporarily releases current lock.

Settings and Adjustments (Continued)

“+” indicates repeater control for the PINP command. (

Repeater control)

» PCLRxxxx (“xxxx” is the current PIN.)

It reverts to the state where no PIN has been set. This is the same as “PIN Clear” under “Control Lock” on the “Setup” menu. (“Permanent unlocking”)

» PCL+xxxx (“xxxx” is the current PIN.)

It reverts to the state where there is no PIN. “+” indicates repeater control for the PCLR command.

Permanent Control lock deactivation (RS-232C)

When a single monitor is connected, use “PCLRxxxx” (“xxxx” is the current PIN.) When multiple monitors are connected, use “PCLR+xxxx”. If the “RS-232C” function is locked, the IDSL and IDLK commands cannot be used.

[Example: 1] Disabling remote control operations

1) From the menu screen, select “Control Lock” from “Setup”.

2) Go to “Lock Items”, then “Remote”, and select “Lock”.

Note: If you exit the menu at this point, the locking will not occur.

3) Go to PIN input, and enter a 4-digit PIN.

4) After PIN input, the set locks will become effective when you close the menu.

[Example: 2] Disabling remote control, monitor buttons and power operations

1) From the menu screen, select “Control Lock” from “Setup”.

2) Go to “Lock Items”, and set “Remote”, “Buttons” and “Power” to “Lock”.

Note: If you exit the menu at this point, the locking will not occur.

3) Go to PIN input screen and enter 4-digit PIN.

4) After PIN input, the set locks will become effective when you close the menu.

[Example: 3] Disabling menu display (RS-232C single connection)

Note: The returned value assumes that no ID has been set.

PCLRxxxx ←(“xxxx” is the current PIN. “xxxx” is not necessary if no PIN has been set.) OK LMNU0001 ←Locks menu display. OK PSETxxxx ←(“xxxx” is new PIN.) OK

Adjustments

Settings and

Settings and Adjustments (Continued)

[Example: 4] Disabling remote control, monitor buttons and power operations (RS-232C daisy-chain

connection)

Note: Values returned by monitors are omitted because they vary depending on the number of

connected monitors.

PCL+xxxx ←(“xxxx” is the current PIN. “xxxx” is not necessary if no PIN is set.) LREM001+ ←Locks remote control LBTN001+ ←Locks monitor buttons LPOW001+ ←Locks power operation PSE+xxxx ←(“xxxx” is new PIN.)

[Example: 5] Disabling remote control operation, operation using monitor buttons, and switching to the

power standby state using those controls for a specific monitor (example: ID=2) in a chain of monitors connected via RS-232C.

Note: Response messages are omitted for convenience as the number of connected monitors

varies.

IDLK0002 ←Select monitor with ID=2 PCLRxxxx ←(“xxxx” is the current PIN. “xxxx” is not necessary if no PIN is set.) LREM0001 ←Locks remote control LBTN0001 ←Locks monitor buttons LPOW0001 ←Locks power operation PSETxxxx ←(“xxxx” is new PIN.) IDLK0000 ←Exit “IDLK” command

If you forget your PIN

If you forget the PIN which you yourself set, perform the following operation when the PIN input screen is displayed.

This allows you to temporarily unlock the function.

MENUENTER

60

Settings and Adjustments (Continued)

● Enlarge

■ You can set up 4 or 9 monitors and integrate them into a single screen to display video. Each

monitor displays an enlargement of 1/4 or 1/9 of the original image.

How to use the “Enlarge” feature

4 screen monitor set-up

4 monitors

9 screen monitor set-up

9 monitors

546

1 2 3

4 5 6

7 8 9

Adjustments

Settings and

Settings and Adjustments (Continued)

● Wide Mode (INPUT3 (RGB) /(PC (analog))

■ In PC mode, you can select the following screen sizes to suit the input signal.

Input signal Normal Full Dot by DotCinema

4:3 image

640 x 400, 720 x 400 640 x 480, 800 x 600

832 x 624, 1024 x 768

16:9 image

848 x 480 852 x 480

1280 x 768

16:9 image

1366 x 768

5:4 image

Displays image so it fills the screen vertically, while maintaining the original aspect ratio.

An image fully fills the screen. Detects the resolution of the

An image fully fills the screen.

Keep the original aspect ratio in a full screen display. The top and bottom of the image is slightly cropped.

signal and displays an image with the same number of pixels on the screen.

Detects the resolution of the signal and displays an image with the same number of pixels on the screen.

1280 x 1024

Displays image so it fills the screen vertically, while maintaining the original aspect ratio.

An image fully fills the screen.

Keep the original aspect ratio in a full screen display. The top and bottom of the image is slightly cropped.

What is “Dot by Dot”?

■ This function detects the resolution of the signal from a PC and displays an image with the same

number of pixels, dot by dot. (See “Appendix 1: PC compatibility chart” on page 68).

62

Normal

For 4:3 “Standard” pictures. A side bar appears on each side.

Full 14 : 9

For 14:9 squeeze pictures. A thin side bar appears on each side.

Zoom 14 : 9

For 14:9 letterbox pictures. An image vertically fills the screen.

Panorama

In this mode the picture is progressively stretched toward each side of the screen.

Full

Takes an image which has been compressed from 16:9 to 4:3, restores it to the original 16:9, and displays it so it fills the entire screen.

Cinema 14 : 9

Displays Cinescope 14:9 size movie software so it fills the entire screen.

Cinema 16 : 9

For 16:9 letterbox pictures. An image fully fills the screen.

Displays edge portion of the image which is normally cut off.

Underscan

Settings and Adjustments (Continued)

● Wide Mode (Video, S-video, Input 3 COMPONENT)

The desired screen size can be selected to suit the input broadcast or software.

■ The following 8 screen sizes can be selected.

Adjustments

Settings and

Special processing is performed for underscan, so switching takes more time than other screen sizes. This is not a malfunction. “Underscan” employs special processing, so only some picture related adjustments can be used.

Settings and Adjustments (Continued)

» When set to “Enlarge” (i.e. with a “2 × 2” or “3 × 3” setting), the screen size is fixed in “Full” mode.

NOTE:

Tips:

» When using the screen size selection function of this monitor, the appearance of the original video may change if

you select a screen size with a different aspect ratio than the original image (i.e. TV broadcast or video input from an external device). Please consider this point when selecting the screen size.

» Using this monitor’s screen size switching function to compress or expand the screen for commercial or public

viewing in establishments like cafes or hotels may infringe on the rights of creators, as protected by Copyright Law, so please be careful.

» When ordinary non-wide image (4:3) is viewed with the whole screen using the screen size switching function of

this monitor, the edge of the image may be lost or appear distorted. If you wish to respect the creator’s intensions, set the screen size to “Normal”.

» When playing commercial software, parts of the image (like subtitles) image may be cropped. In this case select

the optimal screen size using “Wide Mode” and adjust the vertical position (see “Position” on page 55). With some software, there may be noise or distortion at the edges or top of the screen. This is due to the characteristics of the software, and is not a malfunction.

» Depending on the original image size (i.e. CinemaScope size), black bands may remain at the top and bottom of

the screen.

When operating from Menu screen:

1Press MENU and the MENU screen displays. 2Press \/| to select “Option”. 3Press '/" to select “Wide Mode”, and then press ENTER. 4Press '/"/\/| to select desired screen size. 5Press MENU to turn off the MENU screen.

64

Troubleshooting

Before calling for repair services, make sure following checks for possible remedies to the encountered symptoms.

Problem Check item

There is no picture or sound.

There is no picture.

Remote control does not work.

Right sound

Left

sound

········

Sound from left and right speakers is reversed. Sound is heard from only one side.

There is a picture but no sound

»Is the AC cord disconnected? »Is the Main POWER turned off or is the monitor in

standby mode?

»Make sure external devices are connected properly. »Make sure correct INPUT is selected. »Make sure the connected external device is operating

(playing back).

Has the correct terminal been selected with Input selection?

»The signal may be incompatible. »Make sure sync signals (HD and VD) are connected

correctly (INPUT3 RGB mode). When using INPUT3 (RGB) or PC (analog) input, a sync signal is necessary if the signal does not employ Sync on Green.

»Are the batteries inserted with polarity ( »Are the batteries worn out? »Point the remote control toward the monitor’s remote

control sensor.

»Is Control lock activated? »Are audio cables connected properly?

Make sure audio cables for external speakers are connected properly: left and right cables may be reversed or one of the two cables may not be connected.

»The monitor speaker output is monaural. »Make sure the volume is not set to minimum.

S-video, COMPONENT-video and RGB terminals are for video only. Make sure audio cables are also connected.

»Is the audio corresponding to the selected image being

input?

»Is audio output when monitor speaker output is set to

“On”? If so, the problem is located subsequent to the external speaker output terminal. If not, the problem is in the input terminal or settings.

±, —) aligned?

Page

13 to 17

–

54, 58

13 to 16

–

13 to 16

Adjustments

Settings and

Faint color or bad hue.

Menu screen does not display. Monitor buttons do not work.

RS-232C command does not work.

»Check “Color” and “Tint” adjustments. »When using INPUT3 input, make sure the connection

sequence is correct.

»Is Control lock activated?

»Are matching settings (for baud rate etc.) used on the

PC side?

»Is Control lock activated? »If monitors are chained, make sure connection between

terminals are correct. (The side closer to the PC should be RS-232C INPUT, and the side further from the PC should be RS-232C OUTPUT.)

»Make sure the command is correct. »Did you enter carriage return code (0D

each command?

»Is cross cable used for RS-232C connection? (Straight

cable cannot transmit data).

»Did you receive a response for the previous command?

(Make sure OK or ERR message was returned.)

H) at the end of

51 15

54, 58

and Specifications

Troubleshooting

Troubleshooting (Continued)

■ Warning when temperature rises

Nature of warning:

∫ “Temperature” flashes at the lower right corner of the screen. The monitor automatically enters standby

mode if temperature continues to rise.

Solution:

∫ If the monitor enters standby mode due to a rise in temperature, you can turn on the power on again in

the usual way using the remote control or buttons on the monitor. However the monitor will enter standby mode again if the cause of the temperature rise is not eliminated.

∫ Check whether the monitor is placed at a location where a quick rise in temperature is likely. Internal

temperature rises quickly if the vents on the back are blocked.

∫ Internal temperature rises quickly if dust accumulates inside the monitor or around the vents. Remove

dust if possible. Ask your dealer about removing internal dust.

Cracking sound

The monitor sometimes makes a cracking sound.

» You may hear cracking sound from the monitor. This happens when the cabinet slightly

expands and contracts according to change in temperature. This does not affect the monitor’s performance.

CRACK !

66

Specifications

Product

Model

Screen size

LCD

Panel Drive

Number of dots

Color system

Speaker

Audio amplifier

Terminals

Power requirement

Power consumption

Standby power consumption

Dimensions inch (mm)

Weight lbs. (kg)

Operating temperature 0°C – +40°C

Operating humidity 20% – +80%

inch (mm)

Wide LCD Monitor

LC-M3700/LC-M3710

37” (32-

TFT (thin film transistor) Active Matrix

3,147,264 dots (768 (height) x 1,366 (width) x 3)

NTSC (3.58/4.43MHz), PAL/PAL-60, SECAM

External speakers: 20 W (10 W + 10 W) Built-in monitor speaker: 0.8 W

INPUT1 VIDEO in (BNC), S-video in, AUDIO (L/R) in

INPUT2(INPUT/OUTPUT)

VIDEO OUTPUT VIDEO out (BNC)

INPUT3 (Y/G, Cb/Pb/B, COMPONENT video in/PC (ANALOG) in (BNC),

Cr/Pr/R, HD, VD) AUDIO in (stereo jack, φ 3.5mm)

INPUT3/PC(ANALOG)

OUTPUT

PC(ANALOG)INPUT PC (ANALOG) INPUT in (Mini D-Sub 15 pin),

PC(DIGITAL)INPUT PC (DIGITAL) INPUT in (DVI-D)

RS-232C INPUT terminal (9 pins), RS-232C OUTPUT terminal (9 pins),

SPEAKER terminal (L/R), AC input terminal

AC120V, 60Hz

181 W

0.8 W

37-

41.9 (19) (without stand)

/64 (819.6) (width) x 18-9/64 (460.8) (height), 37-1/64 (940.3) (diagonal))

1-31/32 inch (5 cm), 1 piece

/64 x 3-29/32 x 22-33/64 (949 x 99.5 x 572)

VIDEO in/out (RCA), AUDIO (L/R) in/out

INPUT3/PC (ANALOG) OUTPUT (Mini D-Sub 15 pin)

AUDIO in (stereo jack, φ 3.5 mm)

■ As a part of policy of continuous improvement, SHARP reserves the right to make design and specification changes for product improvement without prior notice. The performance specification figures indicated are nominal values of production units. There may be some deviations from these values in individual units.

■ The Liquid Crystal panel is a very high technology product with 3,147,264 thin film transistors, giving you fine picture details. Occasionally, a few non-active pixels may appear on the screen as a fixed point of blue, green or red. Please note that this does not affect the performance of your product.

Optional accessories

■ The listed optional accessories are available for the Wide LCD Monitor. Please purchase them at your nearest shop.

No. Part name Model name

1 Table stand AN-37ST1

2 Wall-mount bracket AN-37AG1

» Additional optional accessories may be available in the near future. When purchasing, please read the

newest catalogue for compatibility and check the availability.

Mounting precautions

Special techniques are required to mount this monitor, so be sure to rely on a specialist for mounting work. The customer should never perform any of this work himself or herself. Our company will bear no responsibility for accidents or injuries caused by improper mounting or handling.

(As of June 2003)

and Specifications

Troubleshooting

Appendix 1: PC Compatibility Chart

● PC (analog) and INPUT3 (RGB) signal input compatibility chart

Vertical frequency

(∗)

640 × 400 720 × 400 640 × 480 848 × 480 852 × 480 800 × 600 832 × 624 1024 × 768 1280 × 768 1280 × 1024 1366 × 768 540p 1080i 720p

* Interlaced

43Hz

○

      



50Hz

○ ○ ○ ○ ○ ○

○

55Hz

○ ○ ○ ○ ○ ○

○

56Hz

○



○ ○

    



60Hz

○ ○ ○ ○ ○ ○

○ ○ ○ ○ ○ ○ ○

65Hz



○ ○ ○ ○ ○ ○

70Hz

○ ○ ○ ○ ○ ○

○ ○

72Hz

○ ○ ○ ○



 

74.5Hz      

○ ○

75Hz

○ ○ ○ ○ ○ ○

80Hz

○ ○ ○ ○ ○ ○

○

85Hz

○ ○ ○ ○ ○ ○

○

● PC (digital) signal input compatibility chart

640× 480  480p  848× 480 852× 480 800× 600 832× 624 1024× 768 1280× 768 1280× 1024 1366× 768  576p  1080 720p

 640× 480 720× 480 1440× 480         640× 576 720× 576 1440× 576

» Signal timing is confirmed primarily with VESA standard

signals.

» Please note that it may be impossible to display signals with

special timing, even if their resolution is listed in the Table.

» Please be aware that it may be impossible to output special

resolutions with devices like an ordinary PC.

68

Appendix 2: Dimensional Drawings

Unit: inch [mm]

35-25/32 [909]

/64 [810]

31-

[99.5]

37-23/64 [949]

[36]

[66.1]

[462.8]

18-

14-

32-11/32 [821.6]

[13]

[572]

[6.5]

22-

[12]

[24]

/32 [18.5]

1-29/64[37]

[13]

[66.1]

[12.3]

[65]

[370]

/8 [200]

10-

/8 [200]

/16 [265]

/8 [105]

[223]

[200]

[115]

[142]

[72.5]

[155]

[38.5]

13-7/32 [335.8]7-13/32 [188.3]

Appendix

Appendix 3: Menu Option Reference Chart

Menu option reference chart: PC input mode

Picture

Audio

Power control

Setup

Contrast

Black Level

Red

Green

Blue

Advanced

Reset

Treble

Bass

Balance

Reset

Brightness

Power Management

Control Lock

Input Select

Input Signal *

Auto Sync.

Fine Sync.

Picture Flip

Language

INPUT2 Select

ID No. Setting

Enlarge

Panel Protection Cover

0 - 40

–30 - 0 - +30

–10 - 0 - +10

Yes, No

–15 - 0 - +15

L 30 - 0 - R 30

Yes, No

–8 - STD - +8

Off, Mode1, Mode2

C.M.S. (H)

C.M.S. (S)

C.M.S. (V)

Lock Item

PIN Clear

Analog, Digital *

640×480, 720×400, 640×480, 848×480, 852×480,

1024×768, 1280×768, 1366×768, 640×480p *

Start Now

When Connected

H-Pos.

V-Po s.

Clock

Phase

Reset

Normal, Mirror, Upside Down, Rotate

Japanese, English, Deutsch, Français, Español

Input, Output

Input numbers from 000 to 255

Off

2×2

3×3

Attached, Detached

Input 4 digit numbers

Yes, No

0 - 180

0 - 99

0 - 180

0 - 40

Yes, No

Select the position from 1 to 4

Select the position from 1 to 9

C.M.S.

Reset

Menu Display

Remote

Buttons

Powe r

RS-232C

–30 - 0 - +30

Yes, No

Lock, Unlock

70

Option

NOTE:

Wide Mode

DNR

Quick Shoot

Monitor Speaker Output

Normal, Full, Cinema, Dot by Dot *

Off, High, Low

On, Off

*1 May not be displayed for certain signal types. *2 Items displayed may vary according to input signal types. *3 Items displayed may vary according to input signal types. » Depending on the conditions, certain menu items may be displayed in gray. These items cannot be selected.

Appendix 3: Menu Option Reference Chart (Continued)

Menu option reference chart: AV input mode

Picture

Audio

Power control

Setup

Contrast

Black Level

Color

Tint

Sharpness

Advanced

Reset

Treble

Bass

Balance

Reset

Brightness

Power Management

Control Lock

Input Select *

Position

Picture Flip

Language

INPUT2 Select *

ID No. Setting

Enlarge

Panel Protection Cover

0 - 40

–30 - 0 - +30

–10 - 0 - +10

Yes, No

–15 - 0 - +15

L 30 - 0 - R 30

Yes, No

–8 - STD - +8

Off, Mode1, Mode2

C.M.S. (H)

C.M.S. (S)

C.M.S. (V)

Color Temp

Black

3D-Y/C

Monochrome

Film Mode

I/P Setting

Lock Item

PIN Clear

AV, Y/C

COMPONENT, RGB *

H-Pos.

V-Po s.

Reset

Normal, Mirror, Upside Down, Rotate

Japanese, English, Deutsch, Français, Español

Input, Output

Input numbers from 000 to 255

Off

2×2

3×3

Attached, Detached

High, Mid-High, Mid, Mid-Low, Low

Off, High, Low

Standard, Fast, Slow

On, Off

Interlace, Progressive

Input 4 digit numbers

Yes, No

–10 - 0 - +10

–20 - 0 - +20

Yes, No

Select the position from 1 to 4

Select the position from 1 to 9

C.M.S.

Reset

Menu Display

Remote

Buttons

Powe r

RS-232C

–30 - 0 - +30

Yes, No

Lock, Unlock

Option

NOTE:

Wide Mode

Color System

DNR

Quick Shoot

Monitor Speaker Output

Normal, Full 14:9, Zoom 14:9, Panorama, Cinema 14:9, Cinema 16:9, Full, Underscan

Auto, PAL, SECAM, NTSC3.58, NTSC4.43

Off, High, Low

On, Off

*1 This item cannot be chosen if input other than “INPUT1” or “INPUT3” is selected. *2 Available only for “INPUT3” *3 Not available when “INPUT2” is selected. » Depending on the conditions, certain menu items may be displayed in gray. These items cannot be selected.

Appendix

Sharp LC-M3700, LC-M3710 User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual