In the interests of user-safety (Required by safety regulations in some countries) the set should
be restored to its original condition and only parts identical to those specified should be used.
LC-62C42U
OUTLINE
This model is based on the LC-46D62U and is changed some parts. This Service Manual covers the modifications
alone. For the other points, refer to the LC-46/52D62U Service Manual.
CONTENTS
DIFFERENCES FROM BASE MODEL
LIST OF CHANGED PARTS...............................i
[1] REMOVING OF MAJOR PARTS ................... 4-1
Parts marked with "" are important for maintaining the safety of the set. Be sure to replace these parts with specified ones for maintaining the
safety and performance of the set.
This document has been published to be used for
after sales service only.
The contents are subject to change without notice.
MAIN UnitDUNTKD934FM01DUNTKD934FM03 (LC-42D62U) Some parts changed
DUNTKD934FM04 (LC-62C42U) Some parts changed
TERMINAL UnitDUNTKD935FM01DUNTKD935FM03 (LC-42D62U) No parts changed
DUNTKD935FM04 (LC-62C42U) No parts changed
R/C, LED UnitDUNTKD909FM02←—
KEY UnitDUNTKD910FM02←—
POWER SUPPLY UnitRDENCA184WJQZRDENCA192WJQZ—
LCD PANEL
42" WIDE LCD Panel Module Unit—R1LK420D3LF21—
MAIN Unit
R2015 Resistor, 4.7k 1/16W Metal Oxide—VRS-CZ1JF472JYAdd
R2022 Resistor, 4.7k 1/16W Metal OxideVRS-CZ1JF472JY—Delete
R2025 Resistor, 1k 1/16W Metal OxideVRS-CZ1JF102FY—Delete
R2026 Resistor, 1k 1/16W Metal Oxide—VRS-CZ1JF102FYAdd
R2078 Resistor, 10k 1/16W Metal OxideVRS-CZ1JF103FY—Delete
R2079 Resistor, 10k 1/16W Metal Oxide—VRS-CZ1JF103FYAdd
CABINET AND MECHANICAL PARTS
Please refer to a Parts list.
PACKING PARTS AND ACCESSORIES
Please refer to a Parts list.
i
LC-42D62U/LC-62C42U
LC-42D62U/LC-62C42U
SAFETY PRECAUTION
Service Manual
IMPORTANT SERVICE SAFETY PRECAUTION
Service work should be performed only by qualified service technicians who are thoroughly familiar with all safety checks and the
servicing guidelines which follow:
WARNING
1. For continued safety, no modification of any circuit should be
attempted.
2. Disconnect AC power before servicing.
CAUTION: FO R C O N TI NU ED PROTECTION
AGAINST A RISK OF FIRE REPLACE ONLY WITH
SAME TYPE FUSE.
• Use an AC voltmeter having with 5000 ohm per volt, or higher, sensitivity or measure the AC voltage drop across the resistor.
• Connect the resistor connection to all exposed metal parts having a
return to the chassis (antenna, metal cabinet, screw heads, knobs
and control shafts, escutcheon, etc.) and measure the AC voltage
drop across the resistor.
All checks must be repeated with the AC cord plug connection
reversed. (If necessary, a nonpolarized adaptor plug must be used
only for the purpose of completing these checks.)
Any reading of 0.75 Vrms (this corresponds to 0.5 mA rms AC.) or
more is excessive and indicates a potential shock hazard which
must be corrected before returning the monitor to the owner.
DVM
BEFORE RETURNING THE RECEIVER (Fire &
Shock Hazard)
Before returning the receiver to the user, perform the following
safety checks:
3. Inspect all lead dress to make certain that leads are not pinched,
and check that hardware is not lodged between the chassis and
other metal parts in the receiver.
4. Inspect all protective devices such as non-metallic control knobs,
insulation materials, cabinet backs, adjustment and compartment
covers or shields, isolation resistor-capacitor networks, mechanical
insulators, etc.
5. To be sure that no shock hazard exists, check for leakage current in
the following manner.
• Plug the AC cord directly into a 120 volt AC outlet.
• Using two clip leads, connect a 1.5k ohm, 10 watt resistor paralleled by a 0.15µF capacitor in series with all exposed metal cabinet
parts and a known earth ground, such as electrical conduit or electrical ground connected to an earth ground.
Many electrical and mechanical parts in LCD color television have
special safety-related characteristics.
These characteristics are often not evident from visual inspection, nor
can protection afforded by them be necessarily increased by using
replacement components rated for higher voltage, wattage, etc.
Replacement parts which have these special safety characteristics are
identified in this manual; electrical components having such features
are identified by "" and shaded areas in the Replacement Parts List
and Schematic Diagrams.
For continued protection, replacement parts must be identical to those
used in the original circuit.
The use of a substitute replacement parts which do not have the same
safety characteristics as the factory recommended replacement parts
shown in this service manual, may create shock, fire or other hazards.
ii
LC-42D62U/LC-62C42U
PRECAUTIONS A PRENDRE LORS DE LA REPARATION
Ne peut effectuer la réparation qu' un technicien spécialisé qui s'est parfaitement accoutumé à toute vérification de sécurité et aux
conseils suivants.
•
AVERTISSEMENT
1.
N'entreprendre aucune modification de tout circuit. C'est dangereux.
2.
Débrancher le récepteur avant toute réparation.
PRECAUTION:POURLAPROTECTIONCONTINUE CONTRE LES RISQUES D'INCENDIE,
REMPLACER LE FUSIBLE
VERIFICATIONS CONTRE L'INCEN-DIE ET LE
CHOC ELECTRIQUE
Avant de rendre le récepteur à l'utilisateur, effectuer les vérifications suivantes.
Inspecter tous les faisceaux de câbles pour s'assurer que les fils
3.
ne soient pas pincés ou qu'un outil ne soit pas placé entre le châssis et les autres pièces métalliques du récepteur.
4.
Inspecter tous les dispositifs de protection comme les boutons de
commande non-métalliques, les isolants, le dos du coffret, les couvercles ou blindages de réglage et de compartiment, les réseaux
de résistancecapacité, les isolateurs mécaniques, etc.
5.
S'assurer qu'il n'y ait pas de danger d'électrocution en vérifiant la
fuite de courant, de la facon suivante:
•
Brancher le cordon d'alimentation directem-ent à une prise de courant de 120V. (Ne pas utiliser de transformateur d'isolation pour
cet essai).
A l'aide de deux fils à pinces, brancher une résistance de 1.5 kΩ
10 watts en parallèle avec un condensateur de 0.15µF en série
avec toutes les pièces métalliques exposées du coffret et une terre
connue comme une conduite électrique ou une prise de terre
branchée à la terre.
•
Utiliser un voltmètre CA d'une sensibilité d'au moins 5000Ω/V pour
mesurer la chute de tension en travers de la résistance.
•
Toucher avec la sonde d'essai les pièces métalliques exposées qui
présentent une voie de retour au châssis (antenne, coffret métallique, tête des vis, arbres de commande et des boutons, écusson,
etc.) et mesurer la chute de tension CA en-travers de la résistance.
Toutes les vérifications doivent être refaites après avoir inversé la
fiche du cordon d'alimentation. (Si nécessaire, une prise
d'adpatation non polarisée peut être utilisée dans le but de terminer ces vérifications.)
La tension de pointe mesurèe ne doit pas dépasser 0.75V (correspondante au courant CA de pointe de 0.5mA).
Dans le cas contraire, il y a une possibilité de choc électrique qui
doit être supprimée avant de rendre le récepteur au client.
De nombreuses pièces, électriques et mécaniques, dans les téléviseur ACL présentent des caractéristiques spéciales relatives à la sécurité, qui ne sont souvent pas évidentes à vue. Le degré de protection ne peut pas être nécessairement augmentée en utilisant des
pièces de remplacement étalonnées pour haute tension, puissance,
etc.
Les pièces de remplacement qui présentent ces caractéristiques sont
identifiées dans ce manuel; les pièces électriques qui présentent ces
particularités sont identifiées par la marque "" et hachurées dans la
liste des pièces de remplacement et les diagrammes schématiques.
Pour assurer la protection, ces pièces doivent être identiques à celles
utilisées dans le circuit d'origine. L'utilisation de pièces qui n'ont pas
les mêmes caractéristiques que les pièces recommandées par l'usine,
indiquées dans ce manuel, peut provoquer des électrocutions, incendies, radiations X ou autres accidents.
iii
LC-42D62U/LC-62C42U
PRECAUTIONS FOR USING LEAD-FREE SOLDER
Employing lead-free solder
• “PWBs” of this model employs lead-free solder. The LF symbol indicates lead-free solder, and is attached on the PWBs and service manuals. The
alphabetical character following LF shows the type of lead-free solder.
Example:
Indicates lead-free solder of tin, silver and copper.Indicates lead-free solder of tin, silver and copper.
Using lead-free wire solder
• When fixing the PWB soldered with the lead-free solder, apply lead-free wire solder. Repairing with conventional lead wire solder may cause damage or accident due to cracks.
As the melting point of lead-free solder (Sn-Ag-Cu) is higher than the lead wire solder by 40 °C, we recommend you to use a dedicated soldering
bit, if you are not familiar with how to obtain lead-free wire solder or soldering bit, contact our service station or service branch in your area.
Soldering
• As the melting point of lead-free solder (Sn-Ag-Cu) is about 220 °C which is higher than the conventional lead solder by 40 °C, and as it has poor
solder wettability, you may be apt to keep the soldering bit in contact with the PWB for extended period of time. However, Since the land may be
peeled off or the maximum heat-resistance temperature of parts may be exceeded, remove the bit from the PWB as soon as you confirm the
steady soldering condition.
Lead-free solder contains more tin, and the end of the soldering bit may be easily corroded. Make sure to turn on and off the power of the bit as
required.
If a different type of solder stays on the tip of the soldering bit, it is alloyed with lead-free solder. Clean the bit after every use of it.
When the tip of the soldering bit is blackened during use, file it with steel wool or fine sandpaper.
• Be careful when replacing parts with polarity indication on the PWB silk.
75Unbalance, F Type1 for Analog (VHF/UHF/CATV) and Digital (AIR/CABLE)
DIGITAL AUDIO OUTPUT
OUTPUT
OSD language
Power Requirement
Power Consumption
w/o stand
Weight (approx.)
with stand
Dimension*
(WHD)
2
w/o stand
with stand
Operating temperature
1
Emergency alert messages via Cable are unreceivable.
*
2
*
The dimensional drawings are shown on the inside back cover.
As part of policy of continuous improvement, SHARP reserves the right to make design and specification changes for product
•
Optical Digital audio output1 (PCM/Dolby Digital)
Audio out
English/French/Spanish
AC 120 V, 60 Hz
247 W
66.2 lbs./30.0 kg
73.5 lbs./33.3 kg
19
40
/
2637/
32
19
/
40
+++
287/8111/2inch
32
32°F to104°F (0°C to40°C)
64
59/32inch
improvement without prior notice. The performance specification figures indicated are nominal values of production units.
There may be some deviations from these values in individual units.
1 – 1
LC-42D62U/LC-62C42U
CHAPTER 2. OPERATION MANUAL
[1] OPERATION MANUAL
Part names
TV (Front)
LC-42D62U/LC-62C42U
Service Manual
Remote control sensor
OPC sensor*
NOTE
*OPC: Optical Picture Control.
**TV status indicator.
TV (Rear)
HDMI terminal (INPUT 5)
HDMI terminal (INPUT 4)
DIGITAL AUDIO OUTPUT terminal
Antenna/Cable in
Channel buttons
(CH
Volume
buttons
-
(VOL /)
+
OPC indicator*
SLEEP indicator**
POWER indicator**
/)
INPUT
POWER
button
button
AUDIO terminal (INPUT 4)
INPUT 3 terminals
INPUT 1 terminals
INPUT 2 terminals
AUDIO OUTPUT terminals
AC INPUT terminal
2 – 1
LC-42D62U/LC-62C42U
Part names
Remote control unit
114
2
3
4
5
6
7
8
9
10
1123
12
1327
15
16
17
18
19
20
21
22
24
25
26
1 TV POWER: Switch the TV power on or enters standby
mode.
2DISPLAY:Display the channel information.
3 SOURCE POWER: Turns the power of the external
equipment on and off.
4 External equipment operational buttons: Operate the
external equipment.
50_9: Set the channel.
6(DOT):
7 INPUT: Select a TV input source. (TV, INPUT 1, INPUT 2,
INPUT 3, INPUT 4, INPUT 5)
8 VOL / : Set the volume.
9 SURROUND: Select Surround settings.
10 FREEZE: Set the still image. Press again to return to
normal screen.
11 EXIT: Turn off the menu screen.
12 SLEEP: Set the sleep timer.
13 AUDIO: Selects the MTS/SAP or the audio mode during
multi-channel audio broadcasts.
14 FUNCTION: Switches the remote control for TV, CBL/
SAT, VCR, DVD and AUDIO operation. Indicator lights up
for the current mode.
* To enter the code registration mode, you need to press
FUNCTION and DISPLAY at the same time.
15 LIGHT: When pressed all buttons on the remote
control unit will light. The lighting will turn off if no
operations are performed within about 5 seconds. This
button is used for performing operations in low-light
situations.
16 VIEW MODE: Select the screen size.
17 ENT: Jumps to a channel after selecting with the 0_9
buttons.
18 FLASHBACK:Return to the previous channel or external
input mode.
19
CH /: Select the channel.
20 MUTE: Mute the sound.
21 MENU: Display the menu screen.
22////ENTER: Select a desired item on the
screen.
23 RETURN: Return to the previous menu screen.
24 FAVORITE CH
A, B, C, D: Select 4 preset favorite channels in 4 different
categories.
While watching, you can toggle the selected channels by
pressing A, B, C and D.
25 FAVORITE: Register favorite channel.
26 CC: Display captions from a closed-caption source.
NOTE
When using the remote control unit, point it at the TV.
27 AV MODE: Select an audio or video setting. (When the
input source is TV, INPUT 1, 2 or 3: STANDARD, MOVIE,
GAME, USER, DYNAMIC (Fixed), DYNAMIC. When
the input source is INPUT 4 or 5: STANDARD, MOVIE,
GAME, PC, USER, DYNAMIC (Fixed), DYNAMIC)
2 – 2
LC-42D62U/LC-62C42U
Appendix
Removing the stand
Before detaching (or attaching) stand, unplug the AC cord from the AC INPUT terminal.
CAUTION
Do not remove the stand from the TV unless using an optional wall mount bracket to mount it.
Before attaching/detaching stand
Before performing work make sure to turn off the TV.
Before performing work spread cushioning over the base area to lay the TV on. This will prevent it from being
damaged.
1
Unfasten the four screws used to secure the stand in
place.
NOTE
To attach the stand, perform the above steps in reverse order.
Hex key
2
Detach the stand from the TV. (Hold the stand so it will
not drop from the edge of the base area.)
Setting the TV on the wall
CAUTION
This TV should be mounted on the wall only with the AN-37AG2/AN-52AG1 (SHARP) wall mount bracket. The use
of other wall mount brackets may result in an unstable installation and may cause serious injuries.
Installing the TV requires special skill that should only be performed by qualified service personnel. Customers
should not attempt to do the work themselves. SHARP bears no responsibility for improper mounting or
mounting that results in accident or injury.
Using an optional bracket to mount the TV
You can ask a qualified service professional about using an optional AN-37AG2/AN-52AG1 bracket to mount the
TV to the wall.
Carefully read the instructions that come with the bracket before beginning work.
Hanging on the wall
AN-37AG2/AN-52AG1 wall mount bracket.
Vertical mounting
NOTE
Detach the cable clamps on the rear of the TV when using the optional mount bracket.
Angular mounting
About setting the TV angle and height adjustment
0° or 5°
AN-37AG2AN-52AG1
2 – 3
For AN-52AG1
0/5/10/15/20°
-
5/0/ 5 cm
+
(can be moved
5cmupor
down)
LC-42D62U/LC-62C42U
Basic adjustment settings
Menu items for TV/INPUT 1/2/3
Picture
OPC
Backlight
Contrast
Brightness
Color
Tint
Sharpness
Advanced
Color Temp.
Black
3D-Y/C
Monochrome
Film Mode
Range of OPC
Audio
Treble
Bass
Balance
Surround
Power Control
No Signal Off
No Operation Off
Menu items for HDMI (INPUT 4/5)
Picture
OPC
Backlight
Contrast
Brightness
Color
Tint
Sharpness
Advanced
Color Temp.
Black
Monochrome
Film Mode
Range of OPC
Audio
Treble
Bass
Balance
Surround
Power Control
No Signal Off
No Operation Off
EZ Setup
CH Setup
Antenna Setup-DIGITAL
Input Skip
Input Label
Parental CTRL
Position
Language
Reset
Audio Only
Digital Noise Reduction
Input Select
Output Select
Color System
Caption Setup
Program Title Display
Favorite CH
Audio Setup
Setup
Option
Digital Setup
Setup
Input Skip
Input Signal
Input Label
Position
Language
Reset
Option
Audio Only
Digital Noise Reduction
HDMI Setup
Output Select
NOTE
Some menu items may not be displayed depending on the
selected input source.
2 – 4
LC-42D62U/LC-62C42U
CHAPTER 3. DIMENSIONS
[1] DIMENSIONS
21
40
17
/64(540)
19
/32(1031)
LC-42D62U/LC-62C42U
Service Manual
Unit: inch/(mm)
59/32(134)325/32(96)
(733)
8
/
7
28
(200)
8
/
7
7
(675)2
64
/
37
26
(58)
32
/
9
(85)
64
/
23
3
47
/64(933.0)
36
77/8(200)
(526.0)
32
/
23
20
(421)
64
/
37
16
11
1
/2(292)
3 – 1
LC-42D62U/LC-62C42U
LC-42D62U/LC-62C42U
CHAPTER 4. REMOVING OF MAJOR PARTS
Service Manual
[1] REMOVING OF MAJOR PARTS
1. Remove the SD Card Cover.
2. Remove the 4 lock screws and detach the Stand Base Ass'y.
3. Remove the 12 lock screws, 5 lock screws and detach the Rear Cabinet.
3
1
SD Card Cover
3
2
Rear Cabinet
Stand Base Ass'y
4 – 1
4. Remove the 4 lock screws and detach the Chassis Fixing Angle.
5. Remove the 4 lock screws and detach the Center Angle (L)(R).
6. Remove the 2 lock screws and detach the Stand Assist Angle.
7. Remove the 2 lock screws and detach the Stand Assist Cover.
8. Remove the 4 lock screws and detach the Stand Fixing Angle.
9. Remove the 7 lock screws, 1 lock screw and detach the MAIN Shield and Earth Plate.
5
LC-42D62U/LC-62C42U
MAIN Shield
9
Center Angle (R)
9
Earth Plate
Center Angle (L)
5
Stand Fixing Angle
Stand Assist Cover
4 – 2
7
Stand Assist Angle
8
Chassis Fixing Angle
6
4
4
LC-42D62U/LC-62C42U
10.Disconnect all the connectors from all the PWBs.
11.Remove the Top Cover Ass'y. Remove the 1 lock screw from the Top Cover Ass'y and detach the KEY Unit.
Top Cover Ass'y
KEY Unit
11
10
10
10
10
4 – 3
12.Remove the 7 lock screws and detach the Tray Chassis.
13.Remove the 2 lock screws, 3 lock screws, 2 lock screws and detach the Terminal Angle.
14.Remove the 5 lock screws and detach the POWER Unit.
15.Remove the 4 lock screws and detach the TERMINAL Unit.
16.Remove the 3 lock screws, 3 lock screws and detach the MAIN PWB Radiator and MAIN Unit.
17.Remove the 2 lock screws and detach the Speaker (L)(R).
18.Remove the 2 lock screws and detach the R/C, LED Unit.
LC-42D62U/LC-62C42U
MAIN PWB
Radiator
13
13
13
Terminal Angle
16
14
16
MAIN Unit
16
POWER Unit
12
Tray Chassis
TERMINAL Unit
15
Speaker (R)
17
R/C, LED Unit
4 – 4
Speaker (L)
18
17
LC-42D62U/LC-62C42U
19.Remove the 4 lock screws and detach the Tray Fixing Angle (L)(R).
20.Remove the 7 lock screws and detach the Lug Angle Top.
21.Remove the 8 lock screws and detach the Lug Angle Bottom.
22.Remove the LCD Panel Module.
Lug Angle Top
20
20
20
20
20
19
Tray Fixing Angle (R)
19
21
2121
21
21
19
Tray Fixing Angle (L)
19
21
Lug Angle Bottom
4 – 5
PartsGuide
LC-42D62U/LC-62C42U
PARTS GUIDE
No. S86V9LC42D62U
Note:
The reference numbers on the PWB
are arranged in alphabetical order.
[1]PRINTED WIRING BOARD
ASSEMBLIES (NOT
REPLACEMENT ITEM)
[2]LCD PANEL (NOTE: THE PARTS
HERE SHOWN ARE SUPPLIED AS
AN ASSEMBLY BUT NOT
INDEPENDENTLY.)
[3]DUNTKD934FM03/04 (LC-42D62U/
LC-62C42U) (MAIN Unit)
MODELS
CONTENTS
LC-42D62U
LC-62C42U
[4]CABINET AND MECHANICAL
PARTS
[5]SUPPLIED ACCESSORIES
[6]PACKING PARTS (NOT
REPLACEMENT ITEM)
[7]SERVICE JIGS (USE FOR
SERVICING)
Parts marked with "" are important for maintaining the safety of the set. Be sure to replace these
parts with specified ones for maintaining the safety and performance of the set.
This document has been published to be used
for after sales service only.
The contents are subject to change without notice.
N DUNTKD934FM03CQNRMAIN Unit[LC-42D62U]
N DUNTKD934FM04CQNRMAIN Unit[LC-62C42U]
N DUNTKD935FM03BHNXTERMINAL Unit[LC-42D62U]
N DUNTKD935FM04NXTERMINAL Unit[LC-62C42U]
N DUNTKD909FM02AQNXR/C, LED Unit
N DUNTKD910FM02AHNXKEY Unit
N RDENCA192WJQZBUNXPOWER Unit
[2] LCD PANEL (NOTE: THE PARTS HERE SHOWN ARE SUPPLIED AS AN ASSEMBLY BUT NOT INDEPEN-
R2015 VRS-CZ1JF472JYAAJResistor, 4.7k 1/16W Metal Oxide
R2026 VRS-CZ1JF102FYAAJResistor, 1k 1/16W Metal Oxide
R2079 VRS-CZ1JF103FYABJResistor, 10k 1/16W Metal Oxide
2
[4] CABINET AND MECHANICAL PARTS
1
21
43
43
43
43
21
3
34
47
36
20
20
41
41
37
47
8
22
40
51
2
14
42
26
44
44
48
1-1
3-1
3-2
2-1
2-2
1-2
1-3
1-4
1-5
1-6
1-7
1-7
1-7
1-10
1-10
1-7
1-7
1-7
1-8
1-8
1-8
1-9
1-9
1-9
1-9
4
25
5
17
43
43
43
43
18
48
11
10
12
46
54
24
30
35
39
52
38
45
30
31
28
29
15
32
45
13
27
6
9
16
16
23
43
43
43
43
49
48
48
48
48
48
43
45
53
55
45
56
56
45
45
43
50
43
43
48
48
7
6-1
6-2
9-1
7-1
7-2
33
43
TERMINAL Unit
POWER Unit
KEY Unit
R/C, LED Unit
MAIN Unit
9-3
9-3
9-3
9-4
9-4
9-2
19
LC-42D62U/LC-62C42U
3
LC-42D62U/LC-62C42U
NO.PARTS CODE
PRICE
RANK
NEW
MARK
PAR T
DELIVERY
DESCRIPTION
[4] CABINET AND MECHANICAL PARTS
1 CCABAB600WJ01NXFront Cabinet Ass'y[LC-42D62U]
1 CCABAB600WJ02NXFront Cabinet Ass'y[LC-62C42U]
1-1 Not Available-N-Front Cabinet
1-2 Not Available--LED Cover
1-3 Not Available-N-Front Cover
1-4 Not Available--Badge, "SHARP"
1-5 Not Available-N-Shaine Trim
1-6 HPNLSA090WJSANXSP-Net[LC-42D62U]
1-6 HPNLSA090WJSBNXSP-Net[LC-62C42U]
1-7 PSPAHB027WJZZNXSpacer, x6
1-8 Not Available-N-Spacer, x3
1-9 Not Available-N-Spacer, x4
X1 QACCDA039WJPZARXAC Cord
X2 RRMCGA535WJSABANXRemote Control Unit
X3 LHLDWA131WJKZAEJCable Clamp
X4 LHLDWA083WJ00ADXCable Band
X5 TCADEA208WJZZNXEnquete Card
X6 TiNS-C762WJZZAQNXOperation Manual[LC-42D62U]
X6 TiNS-C763WJZZAMNXOperation Manual[LC-62C42U]
X7 Not Available--"AAA" Size Battery
X8 CDAi-A327WJ02NXStand Unit[LC-42D62U]
X8 CDAi-A327WJ04NXStand Unit[LC-62C42U]
X9 TCAUHA184WJZZADXSetup Guide[LC-62C42U]
X10 LHLDWA012WJKZACJWire Holder
PAR T
X3
Cable Clamp
X10
DESCRIPTION
X4
Cable Band
5
LC-42D62U/LC-62C42U
[6] PACKING PARTS (NOT REPLACEMENT ITEM)
S11
S10
S4
S3
S4
S6
S7
S8
S9
S13
S5
S1
S12
S4
S4
S2
6
LC-42D62U/LC-62C42U
NO.PARTS CODE
PRICE
RANK
NEW
MARK
PAR T
DELIVERY
DESCRIPTION
[6] PACKING PARTS (NOT REPLACEMENT ITEM)
S1 SPAKCD081WJZZ-N-Packing Case[LC-42D62U]
S1 SPAKCD082WJZZ-N-Packing Case[LC-62C42U]
S2 SPAKCD085WJZZ-N-Packing Case (Bottom)
S3 SPAKPA774WJZZ-N-Wrapping Paper (Monitor)
S4 SPAKXB298WJZZ-N-Packing Add.
S5 SPAKFB110WJZZ-N-Packing Case (Stand)
S6 SPAKFB111WJZZ-N-Stand Pad[LC-42D62U]
S6 SPAKFB112WJZZ-N-Stand Pad[LC-62C42U]
S7 SPAKPA780WJZZ-N-Wrapping Paper (Mirror Mat Base)
S8 SPAKPA781WJZZ-N-Wrapping Paper (Mirror Mat Sup)
S9 SSAKHA020WJZZ--Polyethylene Bag (for Screw)
S10 SSAKA0101GJZZ--Polyethylene Bag
S11 SSAKAA032WJZZ--Polyethylene Bag
S12 TLABKA009WJZZ--No. Label
S13 SPAKPA602WJZZ--Wrapping Paper (Mirror Mat B)[LC-42D62U]
[7] SERVICE JIGS (USE FOR SERVICING)
N QCNW-C799WJPZAGJRCA Cable L=1500mm, Tuner Extension
N QCNW-D483WJQZAXJ12pins L=1000mm, Main to Power Unit PH (PA)
N QCNW-E068WJQZASJ6pins L=1000mm, Main to Power Unit PD (MI)
N QCNW-E134WJQZBGJ41pins L=400mm, Main to LCD Controller Unit (LV)
N QCNW-F177WJQZBAJ14pins L=1300mm,
NMain/Power to Inverter Unit LA (LB)
N QCNW-F178WJQZAWJ20pins L=1000mm, Main to LCD Controller Unit (LP)
N QCNW-F197WJQZARJ45pins FFC L=1000mm,
NLCD Controller Unit to LCD panel, X 4pcs used
7
LC-42D62U/LC-62C42U
COPYRIGHT2006 BY SHARP CORPORATION
ALL RIGHTS RESERVED.
No part of this publication may be reproduced,
stored in a retrieval system, or transmitted in
any form or by any means, electronic, mechanical,
photocopying, recording, or otherwise, without
prior written permission of the publisher.
TQ2052-S
Sep. 2006 Printed in Japan
Design and Production Information
Design: Japan
Production: SEMEX
SY. KD
SHARP CORPORATION
AV Systems Group
CS Promotion Center
Yaita, Tochigi 329-2193, Japan
Loading...
+ hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.