Sharp LC-15E2E, LC-20E2E Operating Manual

LC-15E2E LC-20E2E

ENGLISH

DEUTSCH

LCD COLOUR TELEVISION LCD-FARBFERNSEHGERÄT TÉLÉVISION COULEUR À ÉCRAN

À CRISTAUX LIQUIDES (LCD) TELEVISORE A COLORI LCD TELEVISIÓN EN COLOR LCD

LCD-FÄRG-TV LCD-KLEURENTELEVISIE

OPERATION MANUAL BEDIENUNGSANLEITUNG MODE D’EMPLOI MANUALE DI ISTRUZIONI

FRANÇAIS

ITALIANO

ESPAÑOL

SVENSKA

MANUAL DE MANEJO BRUKSANVISNING GEBRUIKSAANWIJZING

NEDERLANDS

This equipment complies with the requirements of Directive 89/336/EEC and 73/23/EEC as amended by 93/68/EEC.

Dieses Gerät entspricht den Anforderungen der EG-Richtlinien 89/336/EWG und 73/23/EWG mit Änderung 93/68/EWG.

Ce matériel répond aux exigences contenues dans les directives 89/336/CEE et 73/23/CEE modifiées par la directive 93/68/CEE.

Dit apparaat voldoet aan de eisen van de richtlijnen 89/336/EEG en 73/23/EEG, gewijzigd door 93/68/ EEG.

Dette udstyr overholder kravene i direktiv nr. 89/336/EEC og 73/23/EEC med tillæg nr. 93/68/EEC. Quest’apparecchio è conforme ai requisiti delle direttive 89/336/EEC e 73/23/EEC come emendata

dalla direttiva 93/68/EEC.

Η εγκατάσταση αυτή ανταποκρίνεται στις απαιτήσεις των οδηγιών της Ευρωπαϊκής Ενωσης 89/336/ΕΟΚ και 73/23/ΕΟΚ, #πως οι κανονισµοί αυτοί συµπληρώθηκαν απ# την οδηγία 93/68/ ΕΟΚ.

Este equipamento obedece às exigências das directivas 89/336/CEE e 73/23/CEE, na sua versão corrigida pela directiva 93/68/CEE.

Este aparato satisface las exigencias de las Directivas 89/336/CEE y 73/23/CEE, modificadas por medio de la 93/68/CEE.

Denna utrustning uppfyller kraven enligt riktlinjerna 89/336/EEC och 73/23/EEC så som kompletteras av 93/68/EEC.

Dette produktet oppfyller betingelsene i direktivene 89/336/EEC og 73/23/EEC i endringen 93/68/ EEC.

Tämä laite täyttää direktiivien 89/336/EEC ja 73/23/EEC vaatimukset, joita on muutettu direktiivillä 93/ 68/EEC.

SPECIAL NOTE FOR USERS IN THE U.K.

The mains lead of this product is fitted with a non-rewireable (moulded) plug incorporating a 3A fuse. Should the fuse need to be replaced, a BSI or ASTA approved BS 1362 fuse marked

the same rating as above, which is also indicated on the pin face of the plug, must be used. Always refit the fuse cover after replacing the fuse. Never use the plug without the fuse cover fitted. In the unlikely event of the socket outlet in your home not being compatible with the plug supplied, cut off the mains plug and fit an appropriate type. DANGER: The fuse from the cut-off plug should be removed and the cut-off plug destroyed immedi-

ately and disposed of in a safe manner.

Under no circumstances should the cut-off plug be inserted elsewhere into a 13A socket

outlet, as a serious electric shock may occur. To fit an appropriate plug to the mains lead, follow the instructions below: IMPORTANT: The wires in the mains lead are coloured in accordance with the following code:

Blue : Neutral Brown : Live As the colours of the wires in the mains lead of this product may not correspond with the coloured markings identifying the terminals in your plug, proceed as follows;

• The wire which is coloured blue must be connected to the plug terminal which is marked N or coloured black.

• The wire which is coloured brown must be connected to the plug terminal which is marked L or coloured red.

Ensure that neither the brown nor the blue wire is connected to the earth terminal in your three-pin plug. Before replacing the plug cover make sure that:

• If the new fitted plug contains a fuse, its value is the same as that removed from the cut-off plug.

• The cord grip is clamped over the sheath of the mains lead, and not simply over the lead wires.

IF YOU HAVE ANY DOUBT, CONSULT A QUALIFIED ELECTRICIAN.

ASA

and of

Contents

LC-15E2E

ENGLISH

LC-20E2E

LCD COLOUR TELEVISION

ENGLISH

OPERATION MANUAL

Page Page

Dear SHARP Customer.......................................... 2

Important Safety Precautions ................................. 2

Supplied Accessories ............................................. 4

Preparation ............................................................. 5

Installing Batteries in the Remote Control ...... 5

Using Remote Control ..................................... 5

Power Connection ........................................... 6

Antenna Connection ........................................ 6

First Installation ............................................... 7

Part Names of Main Unit ........................................ 9

Part Names of Remote Control ............................ 11

Basic Operation .................................................... 12

Turning On and Off the Main Power ............. 12

Switching the TV/VIDEO (AV1/AV2/TV) Mode .....

Sound Volume ............................................... 13

ON/OFF Standby ........................................... 13

Changing Channels ....................................... 14

Selecting Menu Items .................................... 15

Useful Features .................................................... 17

Adjusting Picture Settings ............................. 17

Adjusting Sound Settings .............................. 18

Hi-fi Sound Settings ....................................... 19

Using Programme Table ............................... 19

Programmes .................................................. 20

Features ......................................................... 26

On-screen Display ......................................... 28

Child Lock ...................................................... 29

AV Connections ............................................. 34

Timer Functions ............................................. 36

NICAM Broadcast Selection .......................... 37

IGR (German stereo system) Broadcasts ..... 38

Teletext ................................................................. 39

Connecting External Devices ............................... 43

Examples of external devices that can be

connected ................................................... 43

21-pin Euro-SCART (RGB) ........................... 44

How to fix the cables ..................................... 46

Troubleshooting .................................................... 47

Specifications........................................................ 49

Dimensional Drawings .......................................... 50

Dear SHARP Customer

Thank you for your purchase of the SHARP LCD Colour TV product. To ensure safety and many years of trouble-free operation of your product, please read the Important Safety Precautions carefully before using this product.

Important Safety Precautions

Electricity is used to perform many useful functions, but it can also cause personal injuries and property damage if improperly handled. This product has been engineered and manufactured with the highest priority on safety. However, improper use can result in electric shock and/or fire. In order to prevent potential danger, please observe the following instructions when installing, operating and cleaning the product. To ensure your safety and prolong the service life of your LCD colour TV product, please read the following precautions carefully before using the product.

■ Read instructions—All operating instructions must be read and understood before the product is operated.

■ Keep this manual in a safe place—These safety and operating instructions must be kept in a safe place for

future reference.

■ Observe warnings—All warnings on the product and in the instructions must be observed closely.

■ Follow instructions—All operating instructions must be followed.

■ Attachments—Do not use attachments not recommended by the manufacturer. Use of inadequate attach-

ments can result in accidents.

■ Power source—This product must operate on a power source specified on the specification label. If you are not sure of the type of power supply used in your home, consult your dealer or local power company. For units designed to operate on batteries or another power source, refer to the operating instructions.

■ Power cord protection—The power cords must be routed properly to prevent people from stepping on them or objects from resting on them. Check the cords at the plugs and product.

■ If you plan to use a DC power supply unit other than the AC adapter supplied with the product, make sure the power supply unit provides stable voltage with minimum fluctuations. Unstable power supply can cause problems in the product.

■ Overloading—Do not overload AC outlets or extension cords. Overloading can cause fire or electric shock.

■ Entering of objects and liquids—Never insert an object into the product through vents or openings. High voltage flows in the product, and inserting an object can cause electric shock and/or short internal parts. For the same reason, do not spill water or liquid on the product.

■ Servicing—Do not attempt to service the product yourself. Removing covers can expose you to high voltage and other dangerous conditions. Request a qualified service person to perform servicing.

■ Repair—If any of the following conditions occurs, unplug the power cord from the AC outlet, and request a qualified service person to perform repairs: a. When the power cord or plug is damaged. b. When a liquid was spilled on the product or when objects have fallen into the product. c. When the product has been exposed to rain or water. d. When the product does not operate properly as described in the operating instructions.

Do not touch the controls other than those described in the operating instructions. Improper adjustment of controls not described in the instructions can cause damage, which often requires extensive adjust-

ment work by a qualified technician. e. When the product has been dropped or damaged. f. When the product displays an abnormal condition. Any noticeable abnormality in the product indicates

that the product needs servicing.

■ Replacement parts—In case the product needs replacement parts, make sure that the service person uses replacement parts specified by the manufacturer, or those with the same characteristics and performance as the original parts. Use of unauthorized parts can result in fire, electric shock and/or other danger.

■ Safety checks—Upon completion of service or repair work, request the service technician to perform safety checks to ensure that the product is in proper operating condition.

■ Wall or ceiling mounting—When mounting the product on a wall or ceiling, be sure to install the product according to the method recommended by the manufacturer.

Important Safety Precautions (Continued)

■ Cleaning—Unplug the power cord from the AC outlet before

cleaning the product. Use a damp cloth to clean the product. Do not use liquid cleaners or aerosol cleaners.

■ Water and moisture—Do not use the product near water, such

as bathtub, washbasin, kitchen sink and laundry tub, swimming pool and in a wet basement.

■ Stand—Do not place the product on an unstable cart, stand,

tripod or table. Placing the product on an unstable base can cause the product to fall, resulting in serious personal injuries as well as damage to the product. Use only a cart, stand, tripod, bracket or table recommended by the manufacturer or sold with the product. When mounting the product on a wall, be sure to follow the manufacturer’s instructions. Use only the mounting hardware recommended by the manufacturer.

■ When relocating the product placed on a cart, it must be moved

with utmost care. Sudden stops, excessive force and uneven floor surface can cause the product to fall from the cart.

■ Ventilation—The vents and other openings in the cabinet are

designed for ventilation. Do not cover or block these vents and openings since insufficient ventilation can cause overheating and/or shorten the life of the product. Do not place the product on a bed, sofa, rug or other similar surface, since they can block ventilation openings. This product is not designed for built-in installation; do not place the product in an enclosed place such as a bookcase or rack, unless proper ventilation is provided or the manufacturer’s instructions are followed.

■ The LCD panel used in this product is made of glass. Therefore,

it can break when the product is dropped or applied with impact. Be careful not to be injured by broken glass pieces in case the LCD panel breaks.

■ Heat sources—Keep the product away from heat sources such

as radiators, heaters, stoves and other heat-generating products (including amplifiers).

The LCD panel is a very high technology product with 921,600 thin film transistors, giving you fine picture details. Occasionally, a few non-active pixels may appear on the screen as a fixed point of blue, green or red. Please note that this does not affect the performance of your product.

LCD COLOUR TELEVISION LCD-FARBFERNSEHGERÄT TÉLÉVISION COULEUR À ÉCRAN À CRISTAUX LIQUIDES (LCD) TELEVISORE A COLORI LCD TELEVISIÓN EN COLOR LCD LCD-FÄRG-TV LCD-KLEURENTELEVISIE

LC-15E2E LC-20E2E

OPERATION MANUAL BEDIENUNGSANLEITUNG MODE D’EMPLOI MANUALE DI ISTRUZIONI MANUAL DE MANEJO BRUKSANVISNING GEBRUIKSAANWIJZING

ENGLISHDEUTSCHFRANÇAISITALIANOESPAÑOLSVENSKA

NEDERLANDS

Supplied Accessories

Make sure the following accessories are provided with the product.

Wireless remote control (×1)

AC adapter (×1)

R-03 (“AAA” size, UM/SUM-4) dry battery (×2)

AC cord (×1)

Cable clamp (×2)

* Product shape varies in some countries.

Operation manual (×1)

Preparation

Installing Batteries in the Remote Control

Before using the LCD TV set for the first time, install the two R-03 (“AAA” size, UM/SUM-4) batteries supplied in the remote control. When the batteries become depleted and the remote control fails to operate, replace the batteries with new R-03 (“AAA” size, UM/SUM-4) batteries.

1 Open the battery cover. 2 Insert two R-03 (“AAA” size,

UM/SUM-4) batteries.

■ Slide the cover while pressing the ([) part.

■ Position the positive and negative ends of the batteries as indicated in the compartment.

3 Replace the battery cover.

■ Engaging the lower claw with the remote control, close the cover.

Caution!

Precautions regarding batteries

■ Improper use of batteries can result in a leakage of chemicals and/or explosion. Be sure to follow the instructions below.

• Place batteries with their terminals corresponding to the (+) and (–) indications.

• Different types of batteries have different characteristics. Do not mix batteries of different types.

• Do not mix old and new batteries. Mixing old and new batteries can shorten the life of new batteries and/

or cause old batteries to leak chemicals.

• Remove batteries as soon as they are depleted. Chemicals that leak from batteries can cause a rash. If chemical leakage is found, wipe it off with a cloth.

• The batteries supplied with the product may have a shorter life expectancy due to storage conditions.

• If the remote control is not to be used for an extended period of time, remove the batteries from the

remote control.

Using Remote Control

■ Use the remote control by pointing it towards the remote sensor window of the main unit. Objects between the remote control and sensor window may prevent proper operation.

Cautions regarding use of remote control

■ Do not expose the remote control to shock. In addition, do not expose the remote control to liquids, and do not place it in an area with high humidity.

■ Do not install or place the remote control under direct sunlight. The heat may cause deformation of the unit.

■ The remote control may not work properly if the remote sensor window is under direct sunlight or strong lighting. In such a case, change the angle of the lighting or main unit, or operate the remote control closer to the remote sensor window.

Remote sensor indicator Power/Standby indicator Remote sensor window

Preparation (Continued)

Power Connection

Connect to the DC input terminal of the product.

Pull down the hook to open the cover.

2 N I

E D I

O E

D I V

O I

D U

W O P

P N I

V 2 1

To POWER INPUT terminal

Plug into an AC outlet.

Household

power outlet

(DC 12V : LC-15E2E) (DC 13V : LC-20E2E)

AC cord*

* Product shape varies in some countries.

Note:

• Always turn the MAIN POWER

AC adapter

( )

switch of the LCD TV set to OFF when connecting the AC adapter.

• Unplug the AC adapter from the LCD TV set and power outlet when the LCD TV set is not to be used for a long period of time.

Antenna Connection

To enjoy a clearer picture, we recommend that you use an outdoor antenna. The following is a brief explanation of the types of connection that are used for coaxial and feeder cables:

(1)If your outdoor antenna uses a 75-ohm coaxial

cable, change this for a new standard DIN45325 (IEC169-2) plug and plug it into the antenna terminal at the back of TV set via the antenna cable (not supplied).

(2)If your outdoor antenna uses a 300-ohm twin-lead

flat feeder, change this for a 300-ohm to 75-ohm impedance converter and plug it into the antenna terminal at the back of TV set via the antenna cable (not supplied).

75-ohm coaxial cable (round cable)

300-ohm twin-lead flat feeder

To antenna input terminal ( )

2 N I

E D I

O E

D I V

O I

D U

W O P

P N I

V 2 1

Preparation (Continued)

First Installation

When you turn on the LCD TV set for the first time, the First Installation routine, which makes installation easier, is activated. Using this routine, you can select the on-screen display language, and automatically search for and store all the receivable channels.

MAIN

SUBTITLE

SUBPAGE

POWER ( )

TV/VIDEO

TEXT

ROTATE

END

MENUSOUND

TV/VIDEO

]/[

</>

1 Press the MAIN POWER ( )

switch. The “First installation (Language)” screen with a list of the languages for the on-screen display appears.

2 Press ]/[ to select the desired

language, and then press OK. The “First installation (Automatic search)” screen appears in the language selected.

Note:

• You can change the on-screen display language after the First Installation routine by selecting “Language” on the TV menu (see pages 15 and 16).

3 Press ]/[ to select the desired

adjustment item, and then press OK. Then press </> to select the desired item.

4 Press ]/[ to select “Start

search.”

First installation (

English Deutsch Français Español Italiano Nederlands Svenska

First installation (

Country Colour system [ PAL Sound system [ I Start search

First installation (

Country Colour system [ PAL Sound system [ I Start search

)

Language

Automatic search

Back

End

[ UK]

Back

[ UK]

)

End

] ]

Note:

Notes:

Back

End

• AV1 is automatically switched to, when “First installation” is selected. If you selected “First installation”, and

want to return to the previous screen, press Flashback ( ).

Preparation (Continued)

First Installation (Continued)

TEXT

TITLE

SUBPAGE

TV/VIDEO

END

MENUSOUND

5 Press OK to begin the automatic

programme search.

When the search is completed, the new programmes found are displayed in yellow on the programme list.

Start search

42.25MHz PAL-I

8 16 1 9 17 2 1 18 3 11 19 4 12 2 5 13 21 6 14 22 7 15 23

Start search

Search is completed 8 16

S 8

1 11 19

11 12 2

Cancel

6 9 17

1 18

3 13 21 5 14 22 6 15 23

End

6 Press END to exit.

Part Names of Main Unit

Controls

Upper control panel

LC-20E2E

TV/VIDEO

LC-15E2E

Volume (–)/(+)

CH ( )/( )

(MAIN POWER)

TV/VIDEO

To change the vertical angle of the LCD TV set, tilt the screen up to 2.5 degrees forward or 10 degrees backward. The TV set can also be rotated 25 degrees to right and left. Please adjust the angle so that the TV set can be watched most comfortably. (See How to adjust the angle on page 10.)

Speaker

Remote sensor indicator

Remote sensor window

A red indicator blinks when the TV set receives the remote control signal.

POWER/STANDBY indicator

A green indicator lights when the power is on and a red indicator lights when in the standby mode (the indicator will not light when the main power is off).

Note:

• TV/VIDEO, CH( )/( ), Volume (–)/(+) and MENU on the main unit have the same functions as the same buttons

• The LC-15E2E and LC-20E2E have different external dimensions and the positions where the names of the

Note:

on the remote control. Fundamentally, this operation manual provides a description based on operation using the remote control.

buttons are displayed also differ but the same operating procedures are followed for all two models.

Part Names of Main Unit (Continued)

Terminals

AUD

Antenna

AUDIO OUT (L) AUDIO OUT (R) Headphones

How to adjust the angle

Tilt the display by grabbing onto the carrying handle while securely holding down the stand with your other hand.

Carrying handle

E D I

I D

P N I

1 C

O O I

D U

Rear view

AV-IN 1

(21pin Euro-SCART)

S-VIDEO

AV-IN 2

VIDEO

AUDIO (L)

AUDIO (R)

POWER INPUT (DC 12V : LC-15E2E) (DC 13V : LC-20E2E)

-IN

-V

Part Names of Remote Control

Selects the brightness

BRIGHT

of the display.

(P.27)

HOLD

Temporarily holds the

current Teletext page.

(P.42)

(Power)

(P.13)

OK, Programme Table

(P.7)

SUBTITLE

Displays the Teletext

Subtitle directly.

(P.42)

SOUND

Switches the sound

mode. (P.37)

Right / Left Selection

(P.7)

Red, Picture Menu

(P.17)

Green, Sound Menu

(P.18)

Volume (+)/(

(P.13)

Channel Select

(P.14)

Flashback

Returns to the previous

channel. (P.7)

SUBPAGE

Displays the Teletext Subpage directly. (P.41)

TEXT

Displays the Teletext mode screen. (P.39)

REVEAL

Displays hidden information

BRIGHT

TEXT

ROTATE

such as solutions to riddles and puzzles. (P.42)

REVEAL

SUBPAGE

HOLD

SUBTITLE

END

MENUSOUND

)

TV/VIDEO

ROTATE

Rotates the display in every direction. (P.27)

END

Returns to normal screen. (P.8)

Upwards/Downwards Selection, zoom display function (Teletext mode)

(P.7)

Displays the TV menu. (P.15)

Cyan, Status Display

Turns on the status display when the menu is not displayed. (P.28)

Yellow, Timer function Menu

(P.36)

Mute

Switches the sound on and off. (P.13)

CH ( )/( )

Displays previous/next page. (Teletext mode) (P.14)

TV/VIDEO

Switches the input source between AV1, AV2 and TV mode. (P.12)

Basic Operation

AV2

1 S06

AV1

Turning On and Off the Main Power

MAIN POWER ( )

TV/VIDEO

Press the MAIN POWER (

switch. The power/standby indicator instantaneously changes from red to green and the main unit is turned on.

Note:

• The On-screen indicator disappears after a few seconds.

To turn off the main power, press

the MAIN POWER ( ) switch.

Power/Standby indicator

Switching the TV/VIDEO (AV1/AV2/TV) Mode

1 Turn on the power of the

connected video equipment.

2 Press TV/VIDEO to select the

applicable input source. The screen displays AV1, AV2 or TV mode each time TV/VIDEO is pressed.

Note:

• About the video modes

• AV1: Select this when viewing the

signals from the video equipment connected to the AV-IN 1 terminal.

• AV2: Select this when viewing the

signals from the video equipment connected to the AV-IN 2 terminals using the VIDEO or S-VIDEO terminal for video input.

• If both VIDEO and S-VIDEO terminals are connected with cables, the S-VIDEO input terminal is selected as the high priority.

TEXT

TITLE

SUBPAGE

TV/VIDEO

MENUSOUND

TV/ VIDEO

)

On-screen display

1 S06

AV1 mode

AV2 mode

TV mode

Sound Volume

Basic Operation (Continued)

TEXT

SUBPAGE

REV

MENUSOUND

Mute Volume

(+)/(–)

TV/VIDEO

To adjust the volume

Press Volume (+) to increase the

sound volume. The numerical value increases.

Press Volume (–) to decrease the

sound volume. The numerical value decreases.

Volume 50

Volume 10

To mute the sound

Press Mute to temporarily turn off

the sound. “Sound off” is displayed.

Press Mute to turn off the Mute

function. “Sound on” is displayed.

Note:

• When Volume (+)/(–) is pressed in the Mute mode, the sound turns on and the volume indicator is displayed.

• The Mute function is cancelled when is pressed.

Sound off

Sound on

ON/OFF Standby

TEXT

BTITLE

SUBPAGE

TV/VIDEO

MENUSOUND

To turn off the LCD TV

Press . The power/standby indicator will turn red.

To turn the LCD TV back on

Press again. The power/standby indicator will turn green.

Basic Operation (Continued)

Changing Channels

You can select channels using Channel Select or CH ( )/( ).

• To handle the increasing number of channels available, this LCD TV set allows you to select up to 200 channels (0 to 199).

Using Channel Select

When selecting the channel using Channel Select, finish inputting the channel number by holding down the button for the last digit for a moment.

TEXT

SUBPAGE

MENUSOUND

To select a one-digit channel (e.g. Channel 5):

1 Hold down the button.

CH ( )/( )

TV/VIDEO

Channel Select

To select a two/three-digit channel (e.g. Channel 15):

1 Press the button. 2 Hold down the button.

Using CH ( )/( )

Press CH ( ) and the channels change in the order shown below:

1 → 2 → 3 → . . . → 198 → 199 → 0 → 1 → 2 → 3 → . . .

Press CH (

) and the channels change in the order shown below:

3 → 2 → 1 → 0 → 199 → 198 → . . . → 3 → 2 → 1 → . . .

Note:

• Channel “0” is prepared for RF output of VCR.

Basic Operation (Continued)

Selecting Menu Items

• The menus can be used to adjust the various settings of your LCD TV set. Select the desired menu item by following the steps below.

■ Using TV Menus

TEXT

SUBPAGE

REVEAL

</>

END

MENUSOUND

]/[

TV/VIDEO

■ Using Direct Control Menu

Control panel of

the main unit

TV/VIDEO

TV/

VIDEO

Volume

(–)/(+)

(

)/( )

1 Press MENU on the remote

control to display the TV menu.

2 Press ]/[ to select the desired

menu item.

• The cursor moves up or down.

• The cursor indicates the selected

menu item.

3 Press OK to display the setting

screen for the selected menu item.

• Press OK again to adjust the selected item.

• See the next page for a table of the setting screens.

4 Press </> to adjust the selected

item.

5 Press MENU to return to the

previous screen or END to return to the normal screen.

1 Press MENU on the main unit to

display the TV menu.

2 Press CH ( )/( ) to select the

desired menu item.

• The cursor moves up or down.

• The cursor indicates the selected

menu item.

3 Press TV/VIDEO to display the

setting screen for the selected menu item.

• Press TV/VIDEO again to adjust the selected item.

TV menu

Picture Sound Programmes Features AV connections Timer functions First installation Language

TV menu

Picture Sound Programmes Features AV connections Timer functions First installation Language

Back

End

4 Press Volume (–)/(+) to make the

adjustment.

5 Press MENU to return to the

previous screen.

• Each time MENU is pressed, you will return the previous screens.

Note:

• The items displayed differ depending on the setting conditions.

• The item selected is displayed in yellow.

• The adjustment values and settings which were changed before the screen is restored are saved as is in the

Note:

memory.

Basic Operation (Continued)

Selecting Menu Items (Continued)

■ TV Menu Setting Screens

For details on using each setting screen, refer to the page number indicated.

TV menu

Picture Sound Programmes Features AV connections Timer functions First installation Language

Back

End

(Page 17)

Picture menu

Contrast [ 30 Colour [ 0 Black level[ 0 Sharpness [ 0 Red-blue [ 0 Green [ 0 Reset

Back

] ] ] ] ] ]

End

(Page 18–19)

Sound menu

Sound via [ TV Headph. vol. [ 3 Loudsp. sound[ Mono Headph. sound[ Mono AV audio sig.[Sound1+2 Sound wide [ off Balance [

Back

(Page 20–25)

Programmes

Automatic search Manual adjustment Sort Erase programme range Enter/change name

Back

End

] ]

] ] ] ] ]

TV menu

Picture Sound Programmes Features AV connections Timer functions First installation Language

Back

End

(Page 34–35)

AV connections

AV1

)

AV2(Y/C

)

AV2(CVBS For programmes

Back

End

(Page 36)

Timer functions

Time Switch off [ no Alarm [ no Alarm volume [

[

Back

: :

(Page 7)

First installation (

English Deutsch Français Español Italiano Nederlands Svenska

)

Language

Back

End

] ] ] ]

End

(Page 26–33)

Features

Brightness [bright Rotate horizontally[off Rotate vertically [off Auto power off [off On-screen display Child lock

Back

(Page 7)

] ] ] ]

End

Language

English Deutsch Français Español Italiano Nederlands Svenska

Back

End

+ 41 hidden pages