In the interests of user-safety (Required by safety regulations in some countries) the set should be restored
to its original condition and only parts identical to those specified should be used.
CONTENTS
» IMPORTANT SERVICE SAFETY PRECAUTION ................................................................................... 2
» REMOVING OF MAJOR PARTS............................................................................................................11
» ADJUSTING PROCEDURE OF EACH SECTION ................................................................................ 15
» PUBLIC MODE ...................................................................................................................................... 26
» REPLACEMENT PARTS LIST .............................................................................................................. 73
» PACKING OF THE SET......................................................................................................................... 87
LC-15C3U-S
Page
SHARP CORPORATION
This document has been published to be used for
after sales service only.
The contents are subject to change without notice.
LC-13C3U-S
2
2
LC-15C3U-S
IMPORTANT SERVICE SAFETY PRECAUTION
Ë
Service work should be perfomed only by qualified ser vice technicians who are thoroughly familiar with all safety checks and the servicing guidelines which follow:
WARNING
1. For continued safety, no modification of any circuit
should be attempted.
2. Disconnect AC power before servicing.
CAUTION: FOR CONTINUED
PROTECTION A GAINST A RISK OF
FIRE REPLACE ONLY WITH SAME
TYPE F3701 (2.0A, 125V), F3702
A V
(1.6A, 125V), F6500 (1.6A, 125V)
AND F6501 (1.6A, 125V) FUSE.
BEFORE RETURNING THE RECEIVER
(Fire & Shock Hazard)
Before returning the receiver to the user, perform
the following safety checks:
1. Inspect all lead dress to make certain that leads are
not pinched, and check that hardware is not lodged
between the chassis and other metal parts in the
receiver.
2. Inspect all protective devices such as non-metallic
control knobs, insulation materials, cabinet backs,
adjustment and compartment covers or shields,
isolation resistor-capacitor networks, mechanical
insulators, etc.
3. To be sure that no shock hazard exists, check for
leakage current in the following manner.
• Plug the AC cord directly into a 110~240 volt A C outlet,
and connect the DC power cable into the receiver's
DC jack. (Do not use an isolation transformer for this
test).
• Using two clip leads, connect a 50k ohm, 10 watt
resistor paralleled by a 0.15µF capacitor in series with
all exposed metal cabinet parts and a known earth
ground, such as electrical conduit or electrical ground
connected to an earth ground.
• Use an AC voltmeter ha ving with 5000 ohm per volt, or
higher, sensitivity or measure the AC voltage drop
across the resisor.
• Connect the resistor connection to all exposed metal
parts having a return to the chassis (antenna, metal
cabinet, screw heads, knobs and control shafts,
escutcheon, etc.) and measure the AC voltage drop
across the resistor.
All checks must be repeated with the AC cord plug
connection reversed. (If necessary, a nonpolarized
adaptor plug must be used only for the purpose of
completing these checks.)
Any reading of 0.75V peak (this corresponds to 0.5
milliamp. peak A C .) or more is e xcessive and indicates
a potential shock hazard which must be corrected
before returning the monitor to the owner .
Many electrical and mechanical parts in LCD television
have special safety-related characteristics.
These characteristics are often not evident from visual
inspection, nor can protection afforded by them be
necessarily increased by using replacement components
rated for higher voltage , w attage , etc.
Replacement parts which have these special safety
characteristics are identified in this manual; electrical
and shaded areas in the
Schematic Diagrams
For continued protection, replacement parts must be
identical to those used in the original circuit.
The use of a substitute replacement parts which do not
have the same safety characteristics as the factory
recommended replacement parts shown in this service
manual, may create shock, fire or other hazards.
components having such features are identified by “ å”
Ne peut effectuer la réparation qu' un technicien spécialisé qui s'est parfaitement
accoutumé à toute vérification de sécurité et aux conseils suivants.
AVERTISSEMENT
conduite électrique ou une prise de terre branchée à la
terre.
1. N'entreprendre aucune modification de tout circuit.
C'est dangereux.
2. Débrancher le récepteur avant toute réparation.
• Utiliser un voltmètre CA d'une sensibilité d'au moins
5000Ω/V pour mesurer la chute de tension en travers
de la résistance.
• Toucher avec la sonde d'essai les pièces métalliques
exposées qui présentent une voie de retour au châssis
(antenne, coffret métallique, tête des vis, arbres de
commande et des boutons, écusson, etc.) et mesurer
la chute de tension CA en-travers de la résistance.
Toutes les vérifications doivent être refaites après avoir
inversé la fiche du cordon d'alimentation. (Si nécessaire,
une prise d'adpatation non polarisée peut être utilisée
dans le but de terminer ces vérifications.)
A V
PRECAUTION: POUR LA
PRO TECTION CONTINUE CONTRE
LES RISQUES D'INCENDIE,
REMPLACER LE FUSIBLE PAR UN
FUSIBLE DE MEME TYPE F3701
(2.0A, 125V), F3702 (1.6A, 125V),
F6500(1.6A, 125V), F6501(1.6A, 125V)
Tous les courants mesurés ne doivent pas dépasser
0,5 mA.
VERIFICATIONS CONTRE L'INCEN-DIE ET
LE CHOC ELECTRIQUE
Dans le cas contraire, il y a une possibilité de choc
électrique qui doit être supprimée avant de rendre lerécepteur au client.
Avant de rendre le récepteur à l'utilisateur, effectuer
les vérifications suivantes.
1. Inspecter tous les faisceaux de câbles pour s'assurer
que les fils ne soient pas pincés ou qu'un outil ne soit
pas placé entre le châssis et les autres pièces
métalliques du récepteur.
2. Inspecter tous les dispositifs de protection comme les
boutons de commande non-métalliques, les isolants,
le dos du coffret, les couvercles ou blindages de réglage
VTVM
ECHELLE CA
50k ohm
10W
et de compartiment, les réseaux de résistancecapacité, les isolateurs mécaniques, etc.
3. S'assurer qu'il n'y ait pas de danger d'électrocution en
vérifiant la fuite de courant, de la facon suiv ante:
• Brancher le cordon d'alimentation directem-ent à une
0.15 µF
SONDE D'ESSAI
prise de courant de 110-240V. (Ne pas utiliser de
transformateur d'isolation pour cet essai).
• A l'aide de deux fils à pinces, brancher une résistance
de 50 kΩ 10 watts en parallèle avec un condensateur
de 0,15µF en série avec toutes les pièces métalliques
exposées du coffret et une terre connue comme une
De nombreuses pièces, électriques et mécaniques,
dans les téléviseurs présentent des caractéristiques
spéciales relatives à la sécurité, qui ne sont souvent
pas évidentes à vue. Le degré de protection ne peut
pas être nécessairement augmentée en utilisant des
pièces de remplacement étalonnées pour haute tension,
puissance, etc.
Les pièces de remplacement qui présentent ces
caractéristiques sont identifiées dans ce manuel; les
pièces électriques qui présentent ces particularités sont
identifiées par la marque " å " et hachurées dans la
liste des pièces de remplacement et les diagrammes
schématiques.
Pour assurer la protection, ces pièces doivent être
identiques à celles utilisées dans le circuit d'origine.
L'utilisation de pièces qui n'ont pas les mêmes
caractéristiques que les pièces recommandées par
l'usine, indiquées dans ce manuel, peut provoquer des
électrocutions, incendies, radiations X ou autres
accidents.
3
LC-13C3U-S
LC-15C3U-S
Precautions for using lead-free solder
1 Employing lead-free solder
"All PWBs" of this model employs lead-free solder . The LF symbol indicates lead-free solder , and is attached on
the PWBs and service manuals. The alphabetical character following LF shows the type of lead-free solder.
Example:
L Fa
Indicates lead-free solder of tin, silver and copper.
2 Using lead-free wire solder
When fixing the PWB soldered with the lead-free solder, apply lead-free wire solder. Repairing with conventional
lead wire solder may cause damage or accident due to cracks.
As the melting point of lead-free solder (Sn-Ag-Cu) is higher than the lead wire solder by 40ºC, we recommend
you to use a dedicated soldering bit, if you are not familiar with how to obtain lead-free wire solder or soldening
bit, contact our service station or service ranch in your area.
3 Soldering
As the melting point of lead-free solder (Sn-Ag-Cu) is about 220°C which is higher than the conventional lead
solder by 40°C, and as it has poor solder wettabillty, you may be apt to keep the soldering bit in contact with the
PWB for extended period of time. However, Since the land may be peeled off or the maximum heat-resistance
temperature of parts may be excoeded, remove the bit from the PWB as soon as y ou conurm the steady soldering
condition.
Lead-free solder contains more tin, and the end of the soldering bit may be easily corroded. Make sure to tum on
and off the power of the bit as required.
if a different type of solder stays on the tip of the soldering bit, it is alloyed with lead-free solder. Clean the bit after
every use of it.
When the tip of the soldering bit is blackened during use, file it with steel wool or fine sandpaper.
Becareful when replacing parts with polarity indication on the PWB silk.
Lead-free wire solder for servicing
Part N o,★DescriptionCode
ZHNDAi123250EJφ0.3mm250g(1roll)BL
ZHNDAi126500EJφ0.6mm500g(1roll)BK
ZHNDAi12801KEJφ1.0mm1kg(1roll)BM
4
SPECIFICATIONS
LC-13C3U-S
LC-15C3U-S
Items
LCD panel
Number of dots921,600 dots VGA
Video color systemsN358, N443, PAL, PAL-M, PAL-N, SECAM, PAL-60
DestinationUSA/Latin America/Taiwan
TV Standard (CCIR)NTSC/PAL-M/PAL-N
TV functionTV Tuning SystemPLL 181 ch.
STEREOMTS+SAP
CATV125 ch.
Y/C FILTER4-LINE COMB FILTER
Brightness430 cd/m
Lamp life (Fluorescent lamp)60,000 hours
Viewing anglesH: 170° V: 170°
Audio amplifier2.1 W x 2 + 3 W x 1
Speakersø2 in. (ø5 cm), 3 pcs.
Precautions at the time of the side B(back) service of Digital unit.
1. Remove only SC2001 of the FFC for connection between Digital unit(SC2001) and Analog unit(SC3403), and
connect the extended cable (QCNW-A556WJZZ) for service.
2. Remove only P2004 of the Connecting Cord for connection between Digital unit(P2004) and Analog unit(P3702),
and connect the extended cable (QCNW-A552WJZZ) for service.
3. Remove the FFC for connection between Digital unit(SC1203) and LCD panel unit, and connect the extended
cable (QCNW-A553WJZZ) for service.
4. Remove the FFC for connection between Digital unit(SC1202) and LCD panel unit, and connect the extended
cable (QCNW-A556WJZZ) for service.
5. Remove the FFC for connection between Digital unit(SC1201) and LCD panel unit, and connect the extended
cable (QCNW-A555WJZZ) for service.
6. Remove the R/C, LED unit fixing screws(1 pc.).
7. Remove the Digital unit fixing screws(1 pc.), a substrate is reversed.
Digital PWB
(side B)
7
3
SC1202
SC1203
54
P4004
SC1201
Digital PWB
P2003
P3702
P3502
P3502
P3501
P3501
6
SC2001
SC2001
P2004
2
Analog PWB
P3601
R/C, LED PWB
1
Inverter-PWB
P6502
P3703
SC3403
P6501
P6500
StepPart No.Description
1QCNW-A556WJZZExtention Cable 50-pin Digital (SC2001)-Analog (SC3403)
2QCNW-A552WJZZExtention Cable 5-pin Digital (SC2004)-Analog (P3702)
3QCNW-A553WJZZExtention Cable 30-pin Digital (SC1203)-LCD panel
4QCNW-A556WJZZExtention Cable 50-pin Digital (SC1202)-LCD panel
5QCNW-A555WJZZExtention Cable 20-pin Digital (SC1201)-LCD panel
14
LC-13C3U-S
LC-15C3U-S
ADJUSTING PROCEDURE OF EACH SECTION
The best adjustment is made before shipping. If any position deviation is found or after part replace is performed, adjust
as follows.
1.Preparation for Adjustments
(1)Use the exclusive-use AC adapter or stable DC power supply.
AC adapter: UADP-A009WJPZ
DC power supply: 12 ± 0.5V (4.5A)
2.Special mode setting procedure
(1)After initialization of E2PROM the mode is changed to the adjustment mode.
[Procedure]
Connect TP2001 and TP2002 to GND, and turn on the power.
[Description]
» The initialization of microprocessor is as follows.
» AV position, DAC data, G/A data, sound processor data, and video chroma data adjustment values are taken as
defaults.
(2)Adjustment mode
[Procedure]
Short-circuit TP2001 to GND, and turn on the power.
Or short-circuit TP2002 to GND, and turn on the power.
Or holding down the [TV/VIDEO] key and [MENU] key, turn on the main power, and simultaneously press the
(inspection process) [CH "] key and [VOL– ] key to change the mode to the adjustment mode.
[Description]
The manual adjustment or adjustment through communication with the automatic machine is performed.
(3)Shipping setting mode
[Procedure]
Holding down the [TV/VIDEO] key and [MENU] key, turn on the main power, and simultaneously press the
(inspection process) [CH '] key and [VOL+] key to change the mode to the shipping setting mode.
Note: Keep it in mind to turn off the power immediately. If any key-in is accidentally made, the setting will be
canceled.
[Description]
User adjustment and other values are taken as defaults.
If TV is indicated as SETTING COMPLETE, setting has been completed.
3.Cancel of special mode
Turn off the main unit power.
15
LC-13C3U-S
LC-15C3U-S
4.Adjustments
AdjustmentAdjusting conditionsAdjusting method
1B+ Adjustment
(R3760)
2Inch Size setup
(If E2PROM is replaced)
(IC2004)
3Common-bias adjustment
4TAMP adjustment
1. Connect the DC voltmeter to
pin 2 of P3702.
1. Go to the adjustment mode.
1. Receive a B/W channel.
2. Go to the adjustment mode.
3. Select the "COM BIAS" with
[MENU] key.
1. Receive a half color bar signal in the
TV mode so that the top left zone
should turn white 75% as shown below. Other signal can be fed instead
of the half color bar signal, however,
if the point at the vertical 180th line
and horizontal 46th pixel is of white
75%. (Make the adjustment based on
the setting of this point.)
2. Adjust the “NTSC TAMP” setting on
page 2 of adjustment process mode
so that the “Y” reading on the same
page should be BB - CA.
3. Make the same setting for the PALM TAMP and PAL-N TAMP data.
1. Adjust the "B+ Adj" value to
5.0±0.02V with R3760.
* Keep the voltage at pin(2) of P3702
below 5.3V during the adjustment.
1. Select "INCH SIZE" and adjust to
"13"(LC-13C3U-S), "15"(LC-15C3U-S)
with [VOL+] or [VOL-] key.
* The color of "INCH SIZE" must be
yellow.
1. Adjust "COM BIAS" to the darkest
screen with [VOL+] and [VOL-] key.
* The color of "COM BIAS" must be
yellow.
White 75% at
top left zone
Page 2 of adjustment process mode
2
| COM BIAS140
NTSCTAMP27
PAL-M T AMP27
PAL-N T AMP27
RCUTOFF0
GCUTOFF0
BCUTOFF0
G3B3R3000000
G1B4YDF DEB5
TAMP HC9
TAMP LBF
Vertical 180th line and
horizontal 46th pixel
640 pixels
GAIBU VER0.000
480 lines
Y data
(white 100%)
5White balance adjustment
1. Receive the monoscope pattern signal.
2.Adjust the “RCUTOFF” and
“BCUTOFF” settings on page 2 of
adjustment process mode to achieve
an optimum white balance.
16
1. Do not change the “GCUTOFF” setting
because otherwise the black level may
fluctuate.
Air/Cable ............................................................................................................................................. Air
Skip Data_CATV................................................................................................................................. All Skip
Skip Data_AIR .................................................................................................................................... All Skip
Color ................................................................................................................................................... 0
Black Level ......................................................................................................................................... 0
GREEN ............................................................................................................................................... 0
TV Color System................................................................................................................................. N358
AV Color System ................................................................................................................................ Auto
Language ............................................................................................................................................ English
Blue Screen ........................................................................................................................................ Off
EZ Setup Auto Start............................................................................................................................ On
Auto Power Off ................................................................................................................................... Off
Picture Flip.......................................................................................................................................... Normal
AV2 IN/OUT........................................................................................................................................ In
CC/TEXT............................................................................................................................................. OFF
V Chip block(MPAA)..................................................................................................................... None
Sub woofer.......................................................................................................................................... ON
Put the screen in AV1, AV2 or COMPONENT but keep out any signal. Call the adjustment process mode,
select “TEST PATTERN” in the 3rd line of page 9, make the settings 1 thru 6, and the following test patterns
show up.
1-2. Test patterns
» Setting 1
The color bars are displayed as shown at left.
Yellow
Green
Cyan
Magenta
Green
Red
Blue
greengreen
Yellow
» Setting 2
Finer vertical stripes than Setting 1 are displayed.
» Setting 3
Green
BrightBrightDark
» Setting 4
A rather dark green-only pattern is displayed.
» Setting 5
A half-tone green-only pattern is displayed.
» Setting 6
A rather bright green-only pattern is displayed.
[2] IC1201 (LCD controller) test pattern
2-1. Getting the test pattern displayed
Put the screen in AV1, AV2 or COMPONENT but keep out any signal. Call the adjustment process mode,
select “G/A TEST PATTERN” in the 13th line of page 18, turn on the setting, and the following test pattern
shows up.
2-2. Test pattern
The following test pattern appears.
Cyan
Magenta
The green pattern is displayed as shown at left.
W
h
i
t
gradation
e
Dark
Dark
Dark
Black
0-level
Gray scale
Gray
16-level
gradation
Red
Green
Blue
Gray
32-level
gradation
Bright
Bright
Bright
Bright
Gray
48-level
gradation
DarkDark
Dark
Dark
Dark
White
63-level
gradation
Note: When the IC801 and IC1201 test pattern display commands are both turned on at the same time, the IC1201
test pattern is given priority.
18
Pin functions of microprocessor IC (IC2001) RH-iXA460WJZZQ
No
.Pin nameFunction
1V HOLD
2HLF
3MAIN SW
4TIMELED
5M/S OUT
6CSYNC
7IREM1
8BYTE
9CNVSS
Closed caption
Closed caption
Main switch ON[H]/OFF[L]
Off timer LED light-up
N.C.
Composite sync signal
Remote control
Grounding
Grounding
N.C.
N.C.
Reset at “L” level
Microprocessor oscillator connection
Grounding
Microprocessor oscillator connection
Power
OSD clock input
N.C.
Main power input
N.C.
OSD blanking output
DAC1 chip select
DAC2 chip select
D terminal connection detect
N.C.
I2C bus open/closed select input
I2C bus serial clock line 2
I2C bus serial clock line 1
I2C bus serial data line 1
I2C bus serial data line 2
R signal output
G signal output
B signal output
N.C.
N.C.
N.C.
N.C.
N.C.
N.C.
3D Y/C separation IC reset (3D YC)
Fluorescent lamp error detect input
Audio input/output select
N.C.
N.C.
N.C.
N.C.
N.C.
N.C.
Panel gate driver voltage control
Adjustment process
BS fixed selector switch
Main Speaker mute
Sab Speaker mute
Headphone detect at “L” level
Speaker standby (at “H” level)
Panel gate driver voltage check
Line out audio mute
Video input/output select
Multiplex reset at “L” level
N.C.
Power
N.C.
Grounding
N.C.
N.C.
Analog switch 3 (3D YC)
CCD input select 2 (3D YC)
CCD input select 1 (3D YC)
N.C.
N.C.
DC/DC control output
N.C.
N.C.
G/A read enable
G/A data input
G/A chip select
G/A data output
G/A clock
Digital decoder reset
Key input 4
Key input 5
N.C.
N.C.
N.C.
N.C.
N.C.
S terminal connect input at “L” level
AFT voltage input
AGC voltage input
Key input 1
Key input 2
N.C.
DC/DC start-up detect
OSD vertical sync signal
Analog power input (GND)
OSD horizontal sync signal
Closed caption (GND)
OSD power input
Closed caption signal input
19
LC-13C3U-S
LC-15C3U-S
Adjustment process mode menus at a glance
Page Item
Initial setting
13-inch15-inch
FunctionAdjust/modify
Basic settings
1MODELA460A460Model number
INCH SIZE1315Inch unit selectAdjustment
SYSTEMAUTOAUTOColor system select
NTSC PWM FREQOCOOCODimmer frequency setting
PAL PWM FREQOBDOBDDimmer frequency setting
NTSC PWM DUTY00Dimmer duty setting
PAL PWM DUTY00Dimmer duty setting
TV GAINOFFOFFAuto gain setting in TV mode
ERROR NO RESET00Lamp error count & resetNo. of lamp error detections
PUBLIC MODEOFFOFFHOTEL MODE
V-CHIP11VCHIP line mute setting
CANADIAN VCHIPOFFOFFCanadian VCHIP setting
VERMicroprocessor Ver. No. display
RCUTOFF-1-1White balance adjustment (Red)Adjustment
GCUTOFF00Green cutoff adjustment
BCUTOFF-1-1White balance adjustment (Blue)Adjustment
G30000Data read value
B30000Data read value
R30000Data read value
G10000Data read value
B40000Data read value
Y0000Data read value at TAMP adjustmentAdjustment
TAMP HC9C9Y upper limit setting at TAMP adjustment
TAMP LBFBFY lower limit setting at TAMP adjustment
GAIBU VERExternal version display
3TV NTSC CONT5050Video contrast setting (TV NTSC)
TV PAL-M CONT5050Video contrast setting (TV PAL-M)
TV PAL-N CONT5050Video contrast setting (TV PAL-N)
AV NTSC CONTRAST5050Video contrast setting (Composite, S Video)
AV PAL CONTRAST5050Video contrast setting (Composite, S Video)
AV SECAM CONTRAST5050Video contrast setting (Composite, S Video)
AV PAL-M CONTRAST5050Video contrast setting (Composite, S Video)
AV PAL-N CONTRAST5050Video contrast setting (Composite, S Video)
AV PAL60 CONTRAST5050Video contrast setting (Composite, S Video)
G30000Data read value
B30000Data read value
R30000Data read value
G10000Data read value
B40000Data read value
Y0000Data read value
(Same setting as for NTSC TAMP)
(Same setting as for NTSC TAMP)
Audio adjustments
4VOLUME2020Volume
L-BOOST TESTOFFOFFAdjustment process ultra-bass switch
PRESCALE SCART2727Pre-scale setting (External input)
PRESCALE FM/AM-M3333Pre-scale setting (TV)
AVCOFFOFFAVC setting
MSP DATA00Audio IC MSP data write & read
MSP DATAWAITWAITWrite & read execution
CARRIER MUTEONONAudio output setting out of sync with TV
IGR THR12D12DIGR THRESH LEVEL
SP TESTOFFOFFAudio test (FS mute 1,2 ON/OFF)
VPC DATAWAITWAITWrite & read execution
TEST PATTERN00VPC test pattern selectVideo IC test pattern
AUTO LDLY-2-2Y/C phase setting
DVD NTSC CR2525Color density setting (Component)
DVD NTSC CB2828Color density setting (Component)
DVD NTSC TINT+7+7Color tone setting (Component)
DVD NTSC BRIGHTNESS+64+64Brightness setting (Component)
DVD NTSC CONTRAST2828Video setting (Component)
DVD NTSC P FILTER00Peaking filter setting (Component)
DVD NTSC H-PEAKING33Picture quality setting (Component)
DVD NTSC BRIGHT2+9+8Brightness setting 2 (Component)
DVD NTSC CONTRAST24848Video setting 2 (Component)
10DVD PAL CR3131Color density setting (Component)
DVD PAL CB3131Color density setting (Component)
DVD PAL TINT00Color tone setting (Component)
DVD PAL BRIGHTNESS+64+64Brightness setting (Component)
DVD PAL CONTRAST2727Video setting (Component)
DVD PAL P FILTER00Peaking filter setting (Component)
DVD PAL H-PEAKING33Picture quality setting (Component)
DVD PAL BRIGHT2+9+9Brightness setting 2 (Component)
DVD PAL CONTRAST24848Video setting 2 (Component)
Video adjustments (TV, composite & S video)
11N358 TV COLOR26002600Color density setting (TV)
N358 AV COLOR26002600Color density setting (Composite, S video)
N358 TV TINT+70+70Color tone setting (TV)
N358 AV TINT+70+70Color tone setting (Composite, S video)
N358 BRIGHTNESS+9+8Brightness setting (TV, composite, S video)
N358 PEAKING FILTER00Peaking filter setting (TV, composite, S video)
N358 TV H-PEAKING33Picture quality setting (TV)
N358 AV H-PEAKING33Picture quality setting (Composite, S video)
N358 AVO START156156Horizontal position setting
N358 SFIF00Horizontal position setting
N358 SCINC116011601Roundness setting
N358 TV LDLY-2-2Y/C phase setting (TV)
N358 AV LDLY-2-2Y/C phase setting (Composite, S video)
12N443 AV COLOR26002600Color density setting (Composite, S video)
N443 AV TINT+70+70Color tone setting (Composite, S video)
N443 BRIGHTNESS+9+8Brightness setting (TV, composite, S video)
N443 PEAKING FILTER00Peaking filter setting (TV, composite, S video)
N443 AV H-PEAKING33Picture quality setting (Composite, S video)
N443 AVO START156156Horizontal position setting
N443 SFIF00Horizontal position setting
N443 SCINC116011601Roundness setting
N443 AV LDLY-2-2Y/C phase setting (Composite, S video)
Video adjustments (TV, composite & S video)
13PAL AV COLOR26002600Color density setting (Composite, S video)
PAL AV TINT+70+70Color tone setting (Composite, S video)
PAL BRIGHTNESS+9+8Brightness setting (TV, composite, S video)
PAL PEAKING FILTER00Peaking filter setting (TV, composite, S video)
PAL AV H-PEAKING33Picture quality setting (Composite, S video)
PAL AVO START156156Horizontal position setting
PAL SFIF00Horizontal position setting
PAL SCINC116011601Roundness setting
PAL AV LDLY-2-2Y/C phase setting (Composite, S video)
22
LC-13C3U-S
LC-15C3U-S
Page Item
Initial setting
13-inch15-inch
FunctionAdjust/modify
Video adjustments (TV, composite & S video)
14SECAM AV COLOR26002600Color density setting (Composite, S video)
SECAM AV TINT+70+70Color tone setting (Composite, S video)
SECAM BRIGHTNESS+9+8Brightness setting (TV, composite, S video)
SECAM PEAKING FILTER00
SECAM AV H-PEAKING33Picture quality setting (Composite, S video)
SECAM AVO START156156Horizontal position setting
SECAM SFIF00Horizontal position setting
SECAM SCINC116011610Roundness setting
SECAM AV LDLY-2-2Y/C phase setting (Composite, S video)
15PAL-M TV COLOR26002600Color density setting (TV)
PAL-M AV COLOR26002600Color density setting (Composite, S video)
PAL-M TV TINT+70+70Color tone setting (TV)
PAL-M AV TINT+70+70Color tone setting (Composite, S video)
PAL-M BRIGHTNESS+9+8Brightness setting (TV, composite, S video)
PAL-M PEAKING FILTER00
PAL-M TV H-PEAKING33Picture quality setting (TV)
PAL-M AV H-PEAKING33Picture quality setting (Composite, S video)
PAL-M AVO START156156Horizontal position setting
PAL-M SFIF00Horizontal position setting
PAL-M SCINC116011601Roundness setting
PAL-M TV LDLY-2-2Y/C phase setting (TV)
PAL-M AV LDLY-2-2Y/C phase setting (Composite, S video)
16PAL-N TV COLOR26002600Color density setting (TV)
PAL-N AV COLOR26002600Color density setting (Composite, S video)
PAL-N TV TINT+70+70Color tone setting (TV)
PAL-N AV TINT+70+70Color tone setting (Composite, S video)
PAL-N BRIGHTNESS+9+8Brightness setting (TV, composite, S video)
PAL-N PEAKING FILTER00
PAL-N TV H-PEAKING33Picture quality setting (TV)
PAL-N AV H-PEAKING33Picture quality setting (Composite, S video)
PAL-N AVO START156156Horizontal position setting
PAL-N SFIF00Horizontal position setting
PAL-N SCINC116011601Roundness setting
PAL-N TV LDLY-2-2Y/C phase setting (TV)
PAL-N AV LDLY-2-2Y/C phase setting (Composite, S video)
17PAL60 AV COLOR26002600Color density setting (Composite, S video)
PAL60 AV TINT+70+70Color tone setting (Composite, S video)
PAL60 BRIGHTNESS+9+8Brightness setting (TV, composite, S video)
PAL60 PEAKING FILTER00
PAL60 AV H-PEAKING33Picture quality setting (Composite, S video)
PAL60 AVO START156156Horizontal position setting
PAL60 SFIF00Horizontal position setting
PAL60 SCINC116011601Roundness setting
PAL60 AV LDLY-2-2Y/C phase setting (Composite, S video)
AFT DOWN1.81.8AFT reference voltage
NTSC 018C8CInitial settings
NTSC 02C0C0Various settings
NTSC 038181RCUTOFF
NTSC 040000GCUTOFF
NTSC 058181BCUTOFF
NTSC 060B0BHorizontal display position
NTSC 071010Vertical display position
NTSC 080000UV data phase delay
NTSC 094C4CPanel clock adjustment
NTSC 0A4B4BDisplay screen top/bottom mask position
NTSC 108080Test pattern display
NTSC 110000Test pattern data
NTSC 120000Horizontal display mask (Left) position
NTSC 130000Horizontal display mask (Right) position
NTSC E00000FIFO TEST
NTSC E10303Sync polarity reversal
NTSC F00707OFL terminal operation setting
23
LC-13C3U-S
LC-15C3U-S
Page Item
18NTSC F10000Inverter frequency setting
NTSC F20000Inverter duty setting
NTSC F3C0C0Dimmer frequency setting, lower level
NTSC F40000Dimmer frequency setting, upper level
NTSC F50000Dimmer PWM setting, lower level
NTSC F60000Dimmer PWM setting, upper level
NTSC F70000OFL 1/2 phase
NTSC 140202System clock setting
G/A TEST PATERNOFFOFFGradation test pattern displayLCD controller IC test pattern
19PAL 018E8EInitial settings
PAL 02C8C8Various settings
PAL 038181RCUTOFF
PAL 040000GCUTOFF
PAL 058181BCUTOFF
PAL 061313Horizontal display position
PAL 071818Vertical display position
PAL 08O2O2UV data phase delay
PAL 094C4CPanel clock adjustment
PAL 0A4A4ADisplay screen top/bottom mask position
PAL 108080Test pattern display
PAL 110000Test pattern data
PAL 120000Horizontal display mask (Left) position
PAL 130000Horizontal display mask (Right) position
PAL E00000FIFO TEST
PAL E10303Sync polarity reversal
PAL F00707OFL terminal operation setting
PAL F10000Inverter frequency setting
PAL F20000Inverter duty setting
PAL F3BDBDDimmer frequency setting, lower level
PAL F40000Dimmer frequency setting, upper level
PAL F50000Dimmer PWM setting, lower level
PAL F60000Dimmer PWM setting, upper level
PAL F70000OFL 1/2 phase
PAL 140202System clock setting
CLOSED CAPTION1515Closed caption thresh level
CCD ISO1616Closed caption phase setting
AIR SERCH1.6001,600
Initial setting
13-inch15-inch
FunctionAdjust/modify
Last synchronous judging frequency at the AIR CH SEARCH
Gradation & COM settings
20V255255255Gradation power reference voltage
V255 BIAS127127Gradation power reference voltage
V235226226Gradation power reference voltage
V235 BIAS127127Gradation power reference voltage
V176138137Gradation power reference voltage
V176 BIAS150150Gradation power reference voltage
V112103103Gradation power reference voltage
V112 BIAS170170Gradation power reference voltage
V647273Gradation power reference voltage
V64 BIAS4040Gradation power reference voltage
V326262Gradation power reference voltage
V32 BIAS4545Gradation power reference voltage
21V214950Gradation power reference voltage
V21 BIAS5050Gradation power reference voltage
V174545Gradation power reference voltage
V17 BIAS5555Gradation power reference voltage
V72929Gradation power reference voltage
V7 BIAS6565Gradation power reference voltage
V000Gradation power reference voltage
V0 BIAS80130Gradation power reference voltage
VGL ADJ2727VGL bias setting
VGL COM215215VGL COM setting
COM181181COM amplitude setting
G/A READDATA00 0000 00Controller read data setting
G/A READDATAWAITWAITRead execution
24
LC-13C3U-S
LC-15C3U-S
Page Item
Initial setting
13-inch15-inch
FunctionAdjust/modify
Three-dimensional settings & sync ID settings
223D Y/C003D ON/OFF setting
3D Y/C DATA003D YC data write & read
3D Y/C DATAWAITWAITWrite & read execution
LSYNC625625Sync ID threshold level (TV)
HSYNC655655Sync ID threshold level (TV)
AVSYNC50005000Sync ID threshold level (External input)
VPC FP20HDATA0000 DATA0000 VPC data read value
VPC FP21HDATA0000 DATA0000 VPC data read value
VPC FP13HDATA0000 DATA0000 VPC data read value
MSP DEMO200HDATA0000 DATA0000 MSP data read value
L ERROR WAIT15s15sLamp error detect wait time
L ERROR H TIME1.0s1.0sLamp error detect time
VPC I2C 20H2424Sync control setting
Power off mode settings & Measure against baund setting
23DENKA PORTOFFOFFPower off mode setting
DENKA TESTP0000Power off mode setting
DENKA TESTP230ms30msPower off mode setting
FP12TIM700700Measure against vertical baund
REMOCON CODEReceived remote control code display
25
LC-13C3U-S
LC-15C3U-S
PUBLIC MODE
1. Outline
The Public mode is designed to limit the functions of LCD TV sets that are set up at hotels , pub lic places (hospitals ,
for example), shop fronts and similar locations.
Note:
In the Public mode, some user settings may fail to be changed later. The Closed Caption, V-Chip, MTS and some
other functions, as well as the volume control must be preset before getting the TV set into the Public mode.
2. Setting procedure
Take the following steps to go to the Public mode.
Call the adjustment process mode, and turn on [PUBLIC MODE]. (Getting started in the Public mode)
On the Public mode setup screen, make necessary settings. (Making settings in the Public mode)
3. Getting started in the Public mode
Hold down the [TV/VIDEO] and [MENU] buttons at once, and press the MAIN POWER switch to power on the TV
set.
Then press the [CH"] and [VOL-] buttons at once to go to the adjustment process mode.
Now press the [MENU] button and select [PUBLIC MODE]. Press the [VOL+] button to turn on the Public mode.
And power off the TV set.
4. Making settings in the Public mode
Before taking the steps below, make sure the TV set is in the Public mode (PUBLIC MODE on).
Hold down the [VOL-] and [CH"] buttons at once, and press the MAIN POWER switch to power on the TV set
again. The PUBLIC MODE screen shows up.
PUBLIC MODE
MAXIMUM VOLUME[ 60 ]
VOLUME FIXED[VARIABLE ]
REMOTE CONTROL[RESPOND]
USER CONTROL[RESPOND ]
ON SCREEN DISPLAY[YES]
AV1 INPUT[NORMAL ]
RESET
ENTER
Using the [CH"] or [CH'] button, select an item.
Using the [VOL-] or [VOL+] button, change the setting.
Note:
Finally be sure to select [ENTER] and press the [VOL-] or [VOL+]
button to save the new setting.
26
LC-13C3U-S
LC-15C3U-S
MAXIMUM VOLUME601~60
ItemDefaultSettingFunction
VOLUME FIXEDVARIABLEVARIABLE
FIXED
REMOTE CONTROLRESPONDRESPOND
NO RESPOND
USER CONTROLRESPONDRESPOND
NO RESPOND
ON SCREEN DISPLAYYESYES
NO
AV1 INPUTNORMALNORMAL
START
AV1 FIXED
RESET
ENTER
Sets the highest sound volume level.
(The volume level is expressed in digital form only.)
Makes the sound volume adjustable.
Keeps the sound volume fixed.
(The sound volume is fixed at the then level. The Volume and
Mute characters are not displayed onscreen.)
Activates the remote controller.
Deactivates the remote controller.
(The buttons on the TV set are operative.)
Activates the buttons on the TV set.
Deactivates the buttons on the TV set.
(The remote controller alone is operative.)
Activates the onscreen display.
Deactivates the onscreen display.
Usual operation.
Enters the AV1 mode when powered on.
(Switchable between TV and VIDEO)
Keeps the TV set fixed at the AV1 mode.
(Unswitchable between TV and VIDEO)
Returns all the settings to their defaults.
Saves new settings.
5. Quitting the Public mode
Hold down the [TV/VIDEO] and [MENU] buttons at once, and press the MAIN POWER switch to power on the TV
set.
Then press the [CH"] and [VOL-] buttons at once to go to the adjustment process mode.
Now press the [MENU] button and select [PUBLIC MODE]. Press the [VOL+] button to turn off the Public mode.
Finally power off the TV set.
Q3603, Q3604 and their peripheral parts as well as pin (42) of IC2001
(2) Inverter circuit (inverter PWB and main PWB)F6700, F6701, F6702, F6703,
(3) Lamp error detection circuit (terminal PWB and main PWB)D3600, D3601,
This model is equipped with the lamp error detection function that detects the current
flowing into the fluorescent lamp and protects the backlight lamp drive circuit.
If a lamp error is detected, the microprocessor interrupts the unit and the ERROR NO
Note:
RESET setting will go up.
13(LC-13C3U-S), 15(LC-15C3U-S)
When the ERROR NO RESET setting has reached "5", the microprocessor turns and
keeps off the unit's power. To resume the power, take the above procedure to clear the
ERROR NO RESET setting.
~
28
Check all the settings on the microprocessor
’s adjust process menu.
No picture
No picture
at all
Yes
No
Are inputs
and outputs
of IC801 as
specified?
Does the LCD
controller test
pattern
appear?
Does the
video decoder
test pattern
appear?
Check IC3401
and its
peripheral
parts.
Check
IC1201, its
peripheral
circuits and
the LCD
panel.
Check IC801
and its
peripheral
circuits.
Yes
No
No
No VIDEO
1 or 2
output
No
Are inputs
and outputs
of IC3401 as
specified?
Check
IC3401 and
its peripheral
parts.
Yes
Check pin (88)
of IC2001,or
check SSW
line.
No
Is input at Pin
(73) of IC801
as specified?
Check IC801,
AV1 line and
t
heir peripheral
parts.
Yes
No S
VIDEO
output
No
Are inputs at
Pins (71) and
(72) of IC801
as specified?
Check
SC3405, SY
line, SC line
and peripheral
parts.
No
COMPONENT
output
No
Is input at
Pins (4), (5),
(6) and (75)
of IC801 as
specified?
Check J3410,
DVD-Y line,
PB line, PR
line and
peripheral
parts.
No TV
output
Yes
No
Are voltages
at Pins (6),
(7) and (9) of
tuner as
specified?
Check the
power line.
No
Is output at
Pin (19) of
tuner as
specified?
No
Check the
tuner and its
peripheral
parts.
Check the
line in
question.
Yes
Is input at pin
(47) of IC3401
as specified?
Yes
Check IC3401
and its
peripheral
parts.
TROUBLE SHOOTING TABLE (Continued)
LC-13C3U-S
LC-15C3U-S
29
LC-13C3U-S
No picture and sound
Yes
No
Do F3701and F3702
function?
Check all the settings on the microprocessor
’s adjust process menu.
No
Are secondary outputs
(+34V, +9V, +5V, -7V, -20V)
of T3701 as specified?
Yes
Are the oscillation waveform
at T3701’s primary side as
specified?
Yes
No
Disconnect F3701and
F3702. Is the load side
short-circuited?
Yes
No
Is any of T3701
’s primary
side, Q3700 and S4701 short-
circuited?
Check J3701, its peripheral
parts and connection cable.
Replace F3701 and F3702.
Check S4701 and
connection cable.
Check the secondary-side
load of T3701.
Fluorescent lamp
Yes
No
Does F6700, F6701,
F6702, F6703, and
F6704 function?
Yes
No
Is Pin (34) of IC1201 at
“H”?
Yes
No
Are the oscillation waveforms
at the primary side of T6700,
T6702, T6704, T6706, and
T6708 as specified?
Yes
Replace F6700, F6701,
F6702, F6703, and F6704.
Yes
Check the line, IC1201 and
its peripheral parts.
Check Q6700 - 6714, T6700
- 6709 and their peripheral
parts.
Replace the fluorescent lamp
and check the oscillation
waveform again.
LC-15C3U-S
TROUBLE SHOOTING TABLE (Continued)
30
TROUBLE SHOOTING TABLE (Continued)
No color
No TV color
No S-VIDEO color
No
Is input at Pin (71) of IC801
as specified?
Check SC3405,IC7101, SC
line and peripheral parts.
No VIDEO color
Check all the settings on the microprocessor
’s adjust process menu.
No COMPONENT color
No
Is input at Pins (4) and (6) of
IC801 as specified?
Check J3410, PB line, PR line
and peripheral parts.
LC-13C3U-S
LC-15C3U-S
31
LC-13C3U-S
No sound
from
speakers
Yes
No
Is pin (53) ,(54)
of IC2001 at
“L”?
Check all the settings on the microprocessor
’s adjust process menu.
No sound
No
Are outputs at
pins (1) and (7)
of IC3301,
IC3302, IC3303,
IC3508 as
specified?
Yes
No
Are inputs at pins
(2) and (4) as well
as outputs at pins
(8) and (12), all of
IC3305, and
IC3507 as
specified?
Muting effect is
on. Check the
PSMUTE 1 and
2 line.
Check IC3301,
IC3302, IC3303
IC3508 and their
peripheral parts.
Yes
Yes
No
Are input and
output of
IC3304 as
specified?
Check IC3304
and its
peripheral parts.
No
Are input and
output of
IC3401 as
specified?
Check IC3401
and its
peripheral parts.
Check the line
in question,
IC3301,IC3507
and its
peripheral parts.
Yes
Check the
speakers and
their peripheral
parts.
No sound
from
headphone
Yes
No
Is pin (55) of
IC2001 at “L”?
Check the
headphone and
its peripheral
parts.
Check Q2007,
J3500, harness
and their
peripheral parts.
No sound
from output
line
Yes
No
Is pin (58) of
IC2001 at “L”?
No
Are outputs at
pins (14) and
(15) of IC3501
as specified?
Yes
Check the line
in question.
Check the
LMUTE line.
Check IC3501,
IC3502, IC3304
and their
peripheral parts.
TV sound
failure
Yes
No
Is output at Pins
(15) and (16) of
tuner as
specified?
No
Is input at pin
(67) of IC3304
as specified?
Yes
Check IC3304,
X3301 and
their peripheral
parts.
Check the
tuner and its
peripheral
parts.
Check Q3201,
Q3202 and
their peripheral
parts.
LC-15C3U-S
TROUBLE SHOOTING TABLE (Continued)
32
CHASSIS LAYOUT
ANALOG Unit
CONTROL Unit
DIGITAL Unit
INVBERTER Unit
R/C, LED Unit
H
G
LC-13C3U-S
LC-15C3U-S
F
E
D
C
B
A
654321
33
LC-13C3U-S
LC-15C3U-S
BLOCK DIAGRAM
H
G
F
E
D
C
B
A
87109654321
34
LC-13C3U-S
LC-15C3U-S
35
17161918151413121110
LC-13C3U-S
LC-15C3U-S
OVERALL WIRING DIAGRAM (LC-13C3U-S)
H
G
F
E
D
C
B
A
87109654321
36
LC-13C3U-S
LC-15C3U-S
37
17161918151413121110
LC-13C3U-S
LC-15C3U-S
OVERALL WIRING DIAGRAM(LC-15C3U-S)
H
G
F
E
D
C
B
A
87109654321
38
LC-13C3U-S
LC-15C3U-S
39
17161918151413121110
LC-13C3U-S
LC-15C3U-S
DESCRIPTION OF SCHEMATIC DIAGRAM
VOLTAGE MEASUREMENT CONDITION:
1. The voltages at test points are measured on
exclusive AC adaptor and the stble supply voltage
of AC 120V. Signals are fed by a color bar signal
generator for servicing purpose and the above
voltages are measured with a 20k ohm/V tester.
INDICATION OF RESISTOR & CAPACITOR:
RESISTOR
1. The unit of resistance “Ω” is omitted.
(K=kΩ=1000 Ω, M=MΩ).
2. All resistors are ± 5%, unless otherwise noted.
(J= ± 5%, F= ± 1%, D= ± 0.5%)
3. All resistors are 1/16W, unless otherwise noted.
4. All resistors are Carbon type, unless otherwise
noted.
C
: Solid
S : Oxide FilmT : Special
N : Metal Coating
CAPACITOR
1. All capacitors are µF, unless otherwise noted.
(P=pF=µµF).
2. All capacitors are 50V, unless otherwise noted.
3. All capacitors are Ceramic type, unless otherwise
noted.
This circuit diagram is original one, therefore there may be a
slight difference from yours.
IMPORTANT SAFETY NOTICE:
PARTS MARKED WITH “å” () ARE
IMPORTANT FOR MAINTAINING THE SAFETY OF
THE SET. BE SURE TO REPLACE THESE PARTS
WITH SPECIFIED ONES FOR MAINTAINING THE
SAFETY AND PERFORMANCE OF THE SET.
AVIS DE SECURITE IMPORTANT:
LES PIECES MARQUEES “å” ( )SONT
IMPORTANTES POUR MAINTENIR LA SECURITE
DE L'APPAREIL.
NE REMPLACER CES PIEDES QUE PAR DES
PIECES DONT LE NUMERO EST SPECIFIE POUR
MAINTENIR LA SECURITE ET PROTEGER LE BON
FONCTIONNEMENT DE L'APPAREIL.
Replacement parts which have these special safety characteristics
identified in this manual; electrical components having such features
are identified by
and Schematic Diagrams. The use of a substitute replacement part
which dose no have the same safety characteristic as the factory
recommended replacement parts shown in this service manual may
create shock, fire or other hazards.
"HOW TO ORDER REPLACEMENT PARTS"
To have your order filled promptly and correctly, please furnish the
following informations.
1. MODEL NUMBER2. REF. NO.
3. PART NO.4. DESCRIPTION
in USA: Contact your nearest SHARP Parts Distributor to order.
Ref. No.Part No.★DescriptionCode
PRINTED WIRING BOARD ASSEMBLIES
NOTE: THE PARTS HERE SHOWN ARE SUPPLIED AS AN
ASSEMBLY BUT NOT INDEPENDENTLY.
å and shaded areas in the Replacement Parts Lists
For location of SHARP Parts Distributor, Please call TollFree; 1-800-BE-SHARP
★ MARK: SPARE PARTS-DELIVERY SECTION
(NOT REPLACEMENT ITEM)
LC-13C3U-S
DUNTKB273FE07– DIGITAL Unit—
DUNTKB617DE01– ANALOG Unit—
DUNTKB618DE01– CONTROL Unit—
DUNTKB619DE01– R/C, LED Unit—
DUNTKB620DE01– INVERTER Unit—
LC-15C3U-S
DUNTKB273FE08– DIGITAL Unit—
DUNTKB617DE02– ANALOG Unit—
DUNTKB618DE02– CONTROL Unit—
DUNTKB619DE02– R/C, LED Unit—
DUNTKB620DE02– INVERTER Unit—
Les pi`eces de rechange qui pr élelesentent ces caract éleristiques
sp éleciales de s élecurit éle, sont identifi élees dans ce manuel : les
pi`eces élelectriques qui pr élesentent ces particularit éles, sont rep
éler élee par la marque å et sont hachur élees dans les listes de
pi`eces et dans les diagrammes sch élematiques.
La substitution d'une pi`ece de rechange par une autre qui ne pr
éLesente pas les m éoemes caract éLeristiques de s élecurit éle que
la pi`ece recommand élee parl'usine et dans ce manuel de service,
peut provoquer une éLelectrocution, un incendie ou toutautre sinistre.
"COMMENT COMMANDER LES PIECES DE RECHANGE"
Pour que votre commande soit r apidement et correctement remplie ,
veuillez fournir les renseignements suivants.
1. NUMERO DU MODELE2. NO. DE REF
3. NO. DE PIECE4. DESCRIPTION
in CANADA: Contact SHARP Electronics of Canada Limited
R401VRS-CY1JF104JYJ 100k 1/16W Metal Oxide AA
R402VRS-CY1JF333JYJ 33k 1/16W Metal Oxide AA
R403VRS-CY1JF103JYJ 10k 1/16W Metal Oxide AA
R404VRS-CY1JF101JYJ 100 1/16W Metal Oxide AA
R405VRS-CY1JF562JYJ 5.6k 1/16W Metal Oxide AA
R406VRS-CY1JF332JYJ 3.3k 1/16W Metal Oxide AA
R408VRS-CY1JF332JYJ 3.3k 1/16W Metal Oxide AA
R409VRS-CY1JF103JYJ 10k 1/16W Metal Oxide AA
R410VRS-CY1JF474JYJ 470k 1/16W Metal Oxide AA
R411VRS-CY1JF101JYJ 100 1/16W Metal Oxide AA
R412VRS-CY1JF562JYJ 5.6k 1/16W Metal Oxide AA
R705VRS-CY1JF1R0JYJ 11/16W Metal Oxide AA
R711VRS-CY1JF103JYJ 10k 1/16W Metal Oxide AA
R712VRS-CY1JF103JYJ 10k 1/16W Metal Oxide AA
R714VRS-CY1JF1R0JYJ 11/16W Metal Oxide AA
R715VRS-CY1JF103JYJ 10k 1/16W Metal Oxide AA
R716VRS-CY1JF102FYJ 1k1/16W Metal Oxide AA
R717VRS-CY1JF362FYJ 3.6k 1/16W Metal Oxide AA
R719VRS-CY1JF823FYJ 82k 1/16W Metal Oxide AA
R726VRS-CY1JF1R0JYJ 11/16W Metal Oxide AA
R801VRS-CB1JF221JYJ 220 1/16W Metal Oxide AC
R802VRS-CB1JF220JYJ 221/16W Metal Oxide AC
R803VRS-CB1JF220JYJ 221/16W Metal Oxide AC
R804VRS-CA1JF101JYJ 100 1/16W Metal Oxide AA
R807VRS-CY1JF750JYJ 751/16W Metal Oxide AA
R808VRS-CY1JF750JYJ 751/16W Metal Oxide AA
R809VRS-CY1JF750JYJ 751/16W Metal Oxide AA
R810VRS-CB1JF220JYJ 221/16W Metal Oxide AC
R811VRS-CY1JF222JYJ 2.2k 1/16W Metal Oxide AA
R812VRS-CY1JF000JYJ 01/16W Metal Oxide AA
R813VRS-CB1JF220JYJ 221/16W Metal Oxide AC
R814VRS-CY1JF332JYJ 3.3k 1/16W Metal Oxide AA
R815VRS-CY1JF101JYJ 100 1/16W Metal Oxide AA
R816VRS-CY1JF470JYJ 471/16W Metal Oxide AA
R819VRS-CY1JF000JYJ 01/16W Metal Oxide AA
R826VRS-CY1JF101JYJ 100 1/16W Metal Oxide AA
R831VRS-CY1JF102JYJ 1k1/16W Metal Oxide AA
R832VRS-CY1JF102JYJ 1k1/16W Metal Oxide AA
R833VRS-CY1JF102JYJ 1k1/16W Metal Oxide AA
R834VRS-CY1JF102JYJ 1k1/16W Metal Oxide AA
R836VRS-CY1JF000JYJ 01/16W Metal Oxide AA
R838VRS-CY1JF000JYJ 01/16W Metal Oxide AA
R844VRS-CY1JF105JYJ 1 M 1/16W Metal Oxide AA
R1001 VRS-CY1JF102JYJ 1k1/16W Metal Oxide AA
R1002 VRS-CY1JF103FYJ 10k 1/16W Metal Oxide AA
R1003 VRS-CY1JF103FYJ 10k 1/16W Metal Oxide AA
R1005 VRS-CY1JF103FYJ 10k 1/16W Metal Oxide AA
R1006 VRS-CY1JF243FYJ 24k 1/16W Metal Oxide AA
R1007 VRS-CY1JF563FYJ 56k 1/16W Metal Oxide AA
R1008 VRS-CY1JF822FYJ 8.2k 1/16W Metal Oxide AA
R1009 VRS-CY1JF682FYJ 6.8k 1/16W Metal Oxide AA
R1013 VRS-CY1JF101JYJ 100 1/16W Metal Oxide AA
R1014 VRS-CY1JF103JYJ 10k 1/16W Metal Oxide AA
R1016 VRS-CY1JF103JYJ 10k 1/16W Metal Oxide AA
R1017 VRS-CY1JF272JYJ 2.7k 1/16W Metal Oxide AA
R1019 VRS-CY1JF473JYJ 47k 1/16W Metal Oxide AA
R1020 VRS-CY1JF472JYJ 4.7k 1/16W Metal Oxide AA
R1021 VRS-TW2ED102JY J 1k1/4WMetal Oxide AA
R1022 VRS-CY1JF000JYJ 01/16W Metal Oxide AA
R1024 VRS-CY1JF123FYJ 12k 1/16W Metal Oxide AA
R1025 VRS-CY1JF000JYJ 01/16W Metal Oxide AA
R1026 VRS-CY1JF000JYJ 01/16W Metal Oxide AA
R1027 VRS-CY1JF123FYJ 12k 1/16W Metal Oxide AA
R1028 VRS-CY1JF123FYJ 12k 1/16W Metal Oxide AA
R1029 VRS-CY1JF123FYJ 12k 1/16W Metal Oxide AA
R1030 VRS-TW2ED150JY J 151/4WMetal Oxide AA
R1033 VRS-CY1JF000JYJ 01/16W Metal Oxide AA
R1034 VRS-CY1JF000JYJ 01/16W Metal Oxide AA
R1106 VRK-CD1JJ333JYJ 33k 1/16W MetalAC
Composition
R1107 VRS-CY1JF103FYJ 10k 1/16W Metal Oxide AA
R1108 VRS-CY1JF103FYJ 10k 1/16W Metal Oxide AA
R1110 VRS-CY1JF104FYJ 100k 1/16W Metal Oxide AA
R1112 VRS-CY1JF103FYJ 10k 1/16W Metal Oxide AA
R1114 VRS-CY1JF103FYJ 10k 1/16W Metal Oxide AA
R1117 VRS-CY1JF102JYJ 1k1/16W Metal Oxide AA
R1118 VRS-CY1JF563FYJ 56k 1/16W Metal Oxide AA
R1119 VRS-CY1JF472FYJ 4.7k 1/16W Metal Oxide AA
R1120 VRS-TX2HF5R6JY J 5.6 1/2WMetal Oxide AB
R1121 VRS-CY1JF181JYJ 180 1/16W Metal Oxide AA
R1123 VRS-CY1JF181JYJ 180 1/16W Metal Oxide AA
R1124 VRS-CY1JF472FYJ 4.7k 1/16W Metal Oxide AA
R1125 VRS-TX2HF101JYJ 100 1/2WMetal Oxide AA
R1126 VRS-CY1JF000JYJ 01/16W Metal Oxide AA
R1127 VRS-TX2HF1R8JY J 1.8 1/2WMetal Oxide AB
R1128 VRS-CY1JF105JYJ 1 M 1/16W Metal Oxide AA
R1129 VRS-CY1JF363FYJ 36k 1/16W Metal Oxide AA
R1130 VRS-TX2HF5R6JY J 5.6 1/2WMetal Oxide AB
R1131 VRS-CY1JF105JYJ 1 M 1/16W Metal Oxide AA
R1132 VRS-CY1JF000JYJ 01/16W Metal Oxide AA
R1134 VRS-CY1JF000JYJ 01/16W Metal Oxide AA
R1140 VRS-CY1JF273FYJ 27k 1/16W Metal Oxide AA
R1142 VRS-CY1JF103FYJ 10k 1/16W Metal Oxide AA
R1143 VRS-CY1JF391JYJ 390 1/16W Metal Oxide AA
R1144 VRS-CY1JF391JYJ 390 1/16W Metal Oxide AA
R1145 VRS-TW2ED5R6JY J 5.6 1/4WMetal Oxide AA
R1146 VRS-TW2ED8R2JY J 8.2 1/4WMetal Oxide AA
R1148 VRS-TX2HF100JYJ 101/2WMetal Oxide AB
R1157 VRS-CY1JF683FYJ 68k 1/16W Metal Oxide AA
R1160 VRS-CY1JF103FYJ 10k 1/16W Metal Oxide AA
R1161 VRS-CY1JF103FYJ 10k 1/16W Metal Oxide AA
R1162 VRS-CY1JF103FYJ 10k 1/16W Metal Oxide AA
R1163 VRS-CY1JF123FYJ 12k 1/16W Metal Oxide AA
R1164 VRS-CY1JF000JYJ 01/16W Metal Oxide AA
R1166 VRS-CY1JF104FYJ 100k 1/16W Metal Oxide AA
R1167 VRS-CY1JF103FYJ 10k 1/16W Metal Oxide AA
R1168 VRS-CY1JF103FYJ 10k 1/16W Metal Oxide AA
R1169 VRK-CD1JJ333JYJ 33k 1/16W MetalAC
Composition
R1170 VRS-CY1JF683FYJ 68k 1/16W Metal Oxide AA
R1171 VRS-CY1JF123FYJ 12k 1/16W Metal Oxide AA
R1172 VRS-CY1JF103FYJ 10k 1/16W Metal Oxide AA
R1174 VRS-CY1JF683FYJ 68k 1/16W Metal Oxide AA
R1175 VRS-CY1JF123FYJ 12k 1/16W Metal Oxide AA
R1176 VRS-CY1JF103FYJ 10k 1/16W Metal Oxide AA
R1177 VRS-CY1JF683FYJ 68k 1/16W Metal Oxide AA
R1178 VRS-CY1JF123FYJ 12k 1/16W Metal Oxide AA
R1179 VRS-CY1JF103FYJ 10k 1/16W Metal Oxide AA
R1182 VRS-CY1JF102JYJ 1k1/16W Metal Oxide AA
R1183 VRS-CY1JF102JYJ 1k1/16W Metal Oxide AA
R1184 VRS-CY1JF102JYJ 1k1/16W Metal Oxide AA
R1185 VRS-CY1JF102JYJ 1k1/16W Metal Oxide AA
R1186 VRS-CY1JF102JYJ 1k1/16W Metal Oxide AA
R1187 VRS-CY1JF102JYJ 1k1/16W Metal Oxide AA
R1188 VRS-CY1JF102JYJ 1k1/16W Metal Oxide AA
R1190 VRS-CY1JF000JYJ 01/16W Metal Oxide AA
R1191 VRS-CY1JF000JYJ 01/16W Metal Oxide AA
R1192 VRS-CY1JF680FYJ 681/16W Metal Oxide AA
R1193 VRS-CY1JF680JYJ 681/16W Metal Oxide AA
R1194 VRS-CY1JF000JYJ 01/16W Metal Oxide AA
R1195 VRS-CY1JF000JYJ 01/16W Metal Oxide AA
R1196 VRS-CY1JF000JYJ 01/16W Metal Oxide AA
R1199 VRS-CY1JF000JYJ 01/16W Metal Oxide AA
R1201 VRS-CY1JF000JYJ 01/16W Metal Oxide AA
R1202 VRK-CD1JJ220JYJ 221/16W MetalAC
Composition
R1203 VRK-CD1JJ220JYJ 221/16W MetalAC
Composition
R1204 VRK-CD1JJ220JYJ 221/16W MetalAC
Composition
R1208 VRS-CY1JF101JYJ 100 1/16W Metal Oxide AA
R1209 VRS-CA1JF220JYJ 221/16W Metal Oxide AA
R1210 VRS-CY1JF220JYJ 221/16W Metal Oxide AA
R1211 VRS-CY1JF221JYJ 220 1/16W Metal Oxide AA
R1212 VRS-CY1JF000JYJ 01/16W Metal Oxide AA
R1214 VRS-CB1JF101JYJ 100 1/16W Metal Oxide AA
R1217 VRS-CY1JF101JYJ 100 1/16W Metal Oxide AA
R1218 VRS-CA1JF101JYJ 100 1/16W Metal Oxide AA
R1221 VRS-CB1JF332JYJ 3.3k 1/16W Metal Oxide AC
R1222 VRS-CB1JF000JYJ 01/16W Metal Oxide AC
R1223 VRS-CA1JF101JYJ 100 1/16W Metal Oxide AA
R1225 VRS-CY1JF472JYJ 4.7k 1/16W Metal Oxide AA
R1226 VRS-CY1JF101JYJ 100 1/16W Metal Oxide AA
R1228 VRS-TX2HF330JYJ 331/2WMetal Oxide AB
R1230 VRS-TV1JD562JYJ 5.6k 1/16W Metal Oxide AA
R1231 VRS-CY1JF000JYJ 01/16W Metal Oxide AA
R1232 VRS-CY1JF101JYJ 100 1/16W Metal Oxide AA
R1233 VRS-CY1JF101JYJ 100 1/16W Metal Oxide AA
R1235 VRS-CB1JF473JYJ 47k 1/16W Metal Oxide AC
R1236 VRS-CB1JF473JYJ 47k 1/16W Metal Oxide AC
R1237 VRS-TX2HF472JYJ 4.7k 1/2WMetal Oxide AB
R1238 VRS-CY1JF101JYJ 100 1/16W Metal Oxide AA
R1240 VRS-CY1JF000JYJ 01/16W Metal Oxide AA
R1243 VRS-CY1JF1R0JYJ 11/16W Metal Oxide AA
R1245 VRS-CY1JF272JYJ 2.7k 1/16W Metal Oxide AA
R1246 VRS-CY1JF272JYJ 2.7k 1/16W Metal Oxide AA
R1247 VRS-CY1JF682JYJ 6.8k 1/16W Metal Oxide AA
R1248 VRS-CY1JF562JYJ 5.6k 1/16W Metal Oxide AA
R1249 VRS-CY1JF103JYJ 10k 1/16W Metal Oxide AA
R1250 VRS-CY1JF000JYJ 01/16W Metal Oxide AA
R1251 VRS-CY1JF000JYJ 01/16W Metal Oxide AA
R1252 VRS-CY1JF000JYJ 01/16W Metal Oxide AA
R1260 VRS-CY1JF000JYJ 01/16W Metal Oxide AA
R1261 VRS-CY1JF000JYJ 01/16W Metal Oxide AA
R2001 VRS-CY1JF102JYJ 1k1/16W Metal Oxide AA
R2002 VRS-CY1JF101JYJ 100 1/16W Metal Oxide AA
R2007 VRS-CY1JF223JYJ 22k 1/16W Metal Oxide AA
R2009 VRS-CY1JF102JYJ 1k1/16W Metal Oxide AA
R2010 VRS-CY1JF101JYJ 100 1/16W Metal Oxide AA
R2011 VRS-CB1JF101JYJ 100 1/16W Metal Oxide AA
R2012 VRS-CA1JF103JYJ 10k 1/16W Metal Oxide AA
R2013 VRS-CA1JF103JYJ 10k 1/16W Metal Oxide AA
R2014 VRS-CA1JF101JYJ 100 1/16W Metal Oxide AA
R2015 VRS-CB1JF331JYJ 330 1/16W Metal Oxide AC
R2016 VRS-CY1JF103JYJ 10k 1/16W Metal Oxide AA
R2017 VRS-CA1JF102JYJ 1k1/16W Metal Oxide AA
R2018 VRS-CY1JF223JYJ 22k 1/16W Metal Oxide AA
R2019 VRS-CY1JF471JYJ 470 1/16W Metal Oxide AA
R2020 VRS-CY1JF105JYJ 1 M 1/16W Metal Oxide AA
R2021 VRS-CY1JF102JYJ 1k1/16W Metal Oxide AA
R2029 VRS-CY1JF223JYJ 22k 1/16W Metal Oxide AA
R2030 VRS-CA1JF333JYJ 33k 1/16W Metal Oxide AA
R2033 VRS-CB1JF101JYJ 100 1/16W Metal Oxide AA
R2036 VRS-CY1JF000JYJ 01/16W Metal Oxide AA
R2037 VRS-CY1JF000JYJ 01/16W Metal Oxide AA
R2041 VRS-CY1JF101JYJ 100 1/16W Metal Oxide AA
R2042 VRS-CY1JF101JYJ 100 1/16W Metal Oxide AA
R2044 VRS-CY1JF103JYJ 10k 1/16W Metal Oxide AA
R2045 VRS-CY1JF103JYJ 10k 1/16W Metal Oxide AA
R2052 VRS-CY1JF101JYJ 100 1/16W Metal Oxide AA
R2053 VRS-CA1JF101JYJ 100 1/16W Metal Oxide AA
R2055 VRS-CA1JF223JYJ 22k 1/16W Metal Oxide AA
R2056 VRS-CY1JF101JYJ 100 1/16W Metal Oxide AA
R2057 VRS-CY1JF223JYJ 22k 1/16W Metal Oxide AA
R2058 VRS-CY1JF000JYJ 01/16W Metal Oxide AA
R2060 VRS-CY1JF103JYJ 10k 1/16W Metal Oxide AA
R2061 VRS-CY1JF101JYJ 100 1/16W Metal Oxide AA
R2067 VRS-CY1JF223JYJ 22k 1/16W Metal Oxide AA
R2068 VRS-CY1JF223JYJ 22k 1/16W Metal Oxide AA
R2071 VRS-CY1JF000JYJ 01/16W Metal Oxide AA
R2072 VRS-CY1JF000JYJ 01/16W Metal Oxide AA
R2074 VRS-CY1JF000JYJ 01/16W Metal Oxide AA
R2075 VRS-CY1JF000JYJ 01/16W Metal Oxide AA
R3201 VRS-CY1JF102JYJ 1k1/16W Metal Oxide AA
R3202 VRS-CY1JF153JYJ 15k 1/16W Metal Oxide AA
R3203 VRS-CY1JF332JYJ 3.3k 1/16W Metal Oxide AA
R3204 VRS-CY1JF152JYJ 1.5k 1/16W Metal Oxide AA
R3205 VRS-CY1JF331JYJ 330 1/16W Metal Oxide AA
R3206 VRS-CY1JF102JYJ 1k1/16W Metal Oxide AA
R3207 VRS-CY1JF102JYJ 1k1/16W Metal Oxide AA
R3208 VRS-CA1JF561JYJ 560 1/16W Metal Oxide AA
R3306 VRS-CY1JF000JYJ 01/16W Metal Oxide AA
R3310 VRS-CY1JF000JYJ 01/16W Metal Oxide AA
R3315 VRS-CY1JF103FYJ 10k 1/16W Metal Oxide AA
R3316 VRS-CY1JF472JYJ 4.7k 1/16W Metal Oxide AA
R3317 VRS-CY1JF103FYJ 10k 1/16W Metal Oxide AA
R3318 VRS-CY1JF472JYJ 4.7k 1/16W Metal Oxide AA
R3319 VRS-CY1JF472FYJ 4.7k 1/16W Metal Oxide AA
R3320 VRS-CY1JF472FYJ 4.7k 1/16W Metal Oxide AA
R3321 VRS-CY1JF103FYJ 10k 1/16W Metal Oxide AA
R3322 VRS-CY1JF103JYJ 10k 1/16W Metal Oxide AA
R3323 VRS-CY1JF103FYJ 10k 1/16W Metal Oxide AA
R3324 VRS-CY1JF103JYJ 10k 1/16W Metal Oxide AA
R3325 VRS-CY1JF683FYJ 68k 1/16W Metal Oxide AA
R3326 VRS-CY1JF683FYJ 68k 1/16W Metal Oxide AA
R3327 VRS-CY1JF154FYJ 150k 1/16W Metal Oxide AA
R3328 VRS-CY1JF154FYJ 150k 1/16W Metal Oxide AA
R3333 VRS-CY1JF223JYJ 22k 1/16W Metal Oxide AA
R3334 VRS-CY1JF223JYJ 22k 1/16W Metal Oxide AA
R3335 VRS-CY1JF471JYJ 470 1/16W Metal Oxide AA
R3336 VRS-CY1JF471JYJ 470 1/16W Metal Oxide AA
R3337 VRS-CY1JF104JYJ 100k 1/16W Metal Oxide AA
R3338 VRS-CY1JF104JYJ 100k 1/16W Metal Oxide AA
R3339 VRS-CY1JF000JYJ 01/16W Metal Oxide AA
R3340 VRS-CY1JF000JYJ 01/16W Metal Oxide AA
R3343 VRS-CY1JF104JYJ 100k 1/16W Metal Oxide AA
R3344 VRS-CY1JF104JYJ 100k 1/16W Metal Oxide AA
R3348 VRS-CY1JF104JYJ 100k 1/16W Metal Oxide AA
R3351 VRS-CY1JF104JYJ 100k 1/16W Metal Oxide AA
R3353 VRS-CY1JF101JYJ 100 1/16W Metal Oxide AA
R3354 VRS-CY1JF101JYJ 100 1/16W Metal Oxide AA
R3355 VRS-CY1JF101JYJ 100 1/16W Metal Oxide AA
R3357 VRS-CY1JF105JYJ 1M 1/16W Metal Oxide AA
R3358 VRS-CY1JF562JYJ 5.6k 1/16W Metal Oxide AA
R3359 VRS-CY1JF101JYJ 100 1/16W Metal Oxide AA
R3362 VRS-CY1JF472JYJ 4.7k 1/16W Metal Oxide AA
(LC-15C3US)
R3364 VRS-CY1JF122JYJ 1.2k 1/16W Metal Oxide AA
R3365 VRS-CY1JF152JYJ 1.5k 1/16W Metal Oxide AA
(LC-13C3US)
R3365 VRS-CY1JF182JYJ 1.8k 1/16W Metal Oxide AA
(LC-15C3US)
R3366 VRS-CY1JF152JYJ 1.5k 1/16W Metal Oxide AA
(LC-13C3US)
R3366 VRS-CY1JF182JYJ 1.8k 1/16W Metal Oxide AA
(LC-15C3US)
R3367 VRS-CY1JF102JYJ 1k1/16W Metal Oxide AA
R3371 VRS-CY1JF000JYJ 01/16W Metal Oxide AA
R3372 VRS-CY1JF000JYJ 01/16W Metal Oxide AA
R3373 VRS-CY1JF000JYJ 01/16W Metal Oxide AA
R3375 VRS-CY1JF000JYJ 01/16W Metal Oxide AA
R3377 VRS-CY1JF000JYJ 01/16W Metal Oxide AA
R3379 VRS-CY1JF822JYJ 8.2k 1/16W Metal Oxide AA
R3380 VRS-CY1JF103JYJ 10k 1/16W Metal Oxide AA
R3381 VRS-CY1JF562JYJ 5.6k 1/16W Metal Oxide AA
R3383 VRS-CY1JF153JYJ 15k 1/16W Metal Oxide AA
R3384 VRS-CY1JF000JYJ 01/16W Metal Oxide AA
R3386 VRS-CY1JF153FYJ 15k 1/16W Metal Oxide AA
R3387 VRS-CY1JF153FYJ 15k 1/16W Metal Oxide AA
R3388 VRS-CY1JF153FYJ 15k 1/16W Metal Oxide AA
R3389 VRS-CY1JF153FYJ 15k 1/16W Metal Oxide AA
R3397 VRS-CY1JF101JYJ 100 1/16W Metal Oxide AA
R3398 VRS-CY1JF101JYJ 100 1/16W Metal Oxide AA
R3401 VRS-CY1JF101JYJ 100 1/16W Metal Oxide AA
R3402 VRS-TQ2BD750JY J 751/8WMetal Oxide AA
R3409 VRS-CY1JF101JYJ 100 1/16W Metal Oxide AA
R3410 VRS-CY1JF101JYJ 100 1/16W Metal Oxide AA
R3411 VRS-TQ2BD750JY J 751/8WMetal Oxide AA
R3412 VRS-TQ2BD750JY J 751/8WMetal Oxide AA
R3413 VRS-CY1JF101JYJ 100 1/16W Metal Oxide AA
R3414 VRS-CY1JF562JYJ 5.6k 1/16W Metal Oxide AA
R3415 VRS-CY1JF562JYJ 5.6k 1/16W Metal Oxide AA
R3420 VRS-CY1JF472JYJ 4.7k 1/16W Metal Oxide AA
R3421 VRS-CY1JF472JYJ 4.7k 1/16W Metal Oxide AA
R3426 VRS-CY1JF562JYJ 5.6k 1/16W Metal Oxide AA
R3427 VRS-CY1JF562JYJ 5.6k 1/16W Metal Oxide AA
R3428 VRS-CY1JF750JYJ 751/16W Metal Oxide AA
R3429 VRS-CY1JF750JYJ 751/16W Metal Oxide AA
R3430 VRS-CY1JF750JYJ 751/16W Metal Oxide AA
R3431 VRS-CY1JF000JYJ 01/16W Metal Oxide AA
R3432 VRS-CY1JF000JYJ 01/16W Metal Oxide AA
R3433 VRS-CY1JF000JYJ 01/16W Metal Oxide AA
R3460 VRS-TQ2BD1R0JY J 11/8WMetal Oxide AA
R3472 VRS-CY1JF622FYJ 6.2k 1/16W Metal Oxide AA
R3473 VRS-CY1JF102FYJ 1k1/16W Metal Oxide AA
R3482 VRS-CY1JF222FYJ 2.2k 1/16W Metal Oxide AA
R3483 VRS-CY1JF222FYJ 2.2k 1/16W Metal Oxide AA
R3484 VRS-CY1JF102JYJ 1k1/16W Metal Oxide AA
R3489 VRS-CY1JF103JYJ 10k 1/16W Metal Oxide AA
R3492 VRS-CY1JF101JYJ 100 1/16W Metal Oxide AA
R3493 VRS-CY1JF101JYJ 100 1/16W Metal Oxide AA
R3496 VRS-CY1JF000JYJ 01/16W Metal Oxide AA
R3497 VRS-CY1JF101JYJ 100 1/16W Metal Oxide AA
R3502 VRS-CY1JF102JYJ 1k1/16W Metal Oxide AA
R3503 VRS-CY1JF102JYJ 1k1/16W Metal Oxide AA
R3514 VRS-CY1JF000JYJ 01/16W Metal Oxide AA
R3515 VRS-CY1JF000JYJ 01/16W Metal Oxide AA
R3520 VRS-CY1JF101JYJ 100 1/16W Metal Oxide AA
R3523 VRS-CY1JF103JYJ 10k 1/16W Metal Oxide AA
R3524 VRS-CY1JF103JYJ 10k 1/16W Metal Oxide AA
R3530 VRS-CY1JF104JYJ 100k 1/16W Metal Oxide AA
R3531 VRS-TQ2BD750JY J 751/8WMetal Oxide AA
R3532 VRS-CY1JF102JYJ 1k1/16W Metal Oxide AA
R3533 VRS-CY1JF680JYJ 681/16W Metal Oxide AA
R3534 VRS-CY1JF101JYJ 100 1/16W Metal Oxide AA
R3535 VRS-CY1JF223JYJ 22k 1/16W Metal Oxide AA
R3536 VRS-CY1JF472JYJ 4.7k 1/16W Metal Oxide AA
R3537 VRS-CY1JF272JYJ 2.7k 1/16W Metal Oxide AA
R3540 VRS-CY1JF000JYJ 01/16W Metal Oxide AA
R3542 VRS-CY1JF680JYJ 681/16W Metal Oxide AA
R3543 VRS-CY1JF562JYJ 5.6k 1/16W Metal Oxide AA
R3544 VRS-CY1JF104JYJ 100k 1/16W Metal Oxide AA
R3545 VRS-CY1JF103JYJ 10k 1/16W Metal Oxide AA
R3546 VRS-CY1JF000JYJ 01/16W Metal Oxide AA
R3547 VRS-CY1JF000JYJ 01/16W Metal Oxide AA
R3550 VRS-TX2HF221JYJ 220 1/2WMetal Oxide AB
R3551 VRS-TX2HF221JYJ 220 1/2WMetal Oxide AB
R3552 VRS-CY1JF153JYJ 15k 1/16W Metal Oxide AA
R3553 VRS-CY1JF000JYJ 01/16W Metal Oxide AA
R3559 VRS-TX2HF000JYJ 01/2WMetal Oxide AB
R3560 VRS-TQ2BD000JY J 01/8WMetal Oxide AA
R3571 VRS-CY1JF562JYJ 5.6k 1/16W Metal Oxide AA
R3572 VRS-CY1JF153JYJ 15k 1/16W Metal Oxide AA
R3573 VRS-CY1JF472JYJ 4.7k 1/16W Metal Oxide AA
(LC-15C3US)
R3573 VRS-CY1JF682JYJ 6.8k 1/16W Metal Oxide AA
(LC-13C3US)
R3574 VRS-CY1JF152JYJ 1.5k 1/16W Metal Oxide AA
(LC-15C3US)
R3574 VRS-CY1JF182JYJ 1.8k 1/16W Metal Oxide AA
(LC-13C3US)
R3575 VRS-CY1JF122JYJ 1.2k 1/16W Metal Oxide AA
R3576 VRS-CY1JF103JYJ 10k 1/16W Metal Oxide AA
R3577 VRS-CY1JF103JYJ 10k 1/16W Metal Oxide AA
R3578 VRS-CY1JF103JYJ 10k 1/16W Metal Oxide AA
R3579 VRS-CY1JF103JYJ 10k 1/16W Metal Oxide AA
R3580 VRS-CY1JF362FYJ 3.6k 1/16W Metal Oxide AA
(LC-13C3US)
R3580 VRS-CY1JF512FYJ 5.1k 1/16W Metal Oxide AA
(LC-15C3US)
R3581 VRS-CY1JF222FYJ 2.2k 1/16W Metal Oxide AA
(LC-13C3US)
R3581 VRS-CY1JF242FYJ 2.4k 1/16W Metal Oxide AA
(LC-15C3US)
R3582 VRS-CY1JF332JYJ 3.3k 1/16W Metal Oxide AA
R3583 VRS-CY1JF103FYJ 10k 1/16W Metal Oxide AA
R3584 VRS-CY1JF102JYJ 1k1/16W Metal Oxide AA
R3585 VRS-CY1JF154FYJ 150k 1/16W Metal Oxide AA
R3586 VRS-CY1JF563FYJ 56k 1/16W Metal Oxide AA
R3600 VRS-CB1JF222JYJ 2.2k 1/16W Metal Oxide AC
R3604 VRS-CB1JF824JYJ 820k 1/16W Metal Oxide AC
R3607 VRS-CB1JF562JYJ 5.6k 1/16W Metal Oxide AC
R3610 VRS-CY1JF563JYJ 56k 1/16W Metal Oxide AA
R3700 VRS-CY1JF472JYJ 4.7k 1/16W Metal Oxide AA
R3701 VRS-CY1JF000JYJ 01/16W Metal Oxide AA
R3702 VRS-TW2ED102JY J 1k1/4WMetal Oxide AA
R3703 VRS-CY1JF274JYJ 270k 1/16W Metal Oxide AA
R3704 VRS-CY1JF133FYJ 13k 1/16W Metal Oxide AA
R3705 VRS-CY1JF184JYJ 180k 1/16W Metal Oxide AA
R3706 VRS-CY1JF100JYJ 101/16W Metal Oxide AA
R3707 VRS-CY1JF105JYJ 1M 1/16W Metal Oxide AA
R3708 VRS-CY1JF682JYJ 6.8k 1/16W Metal Oxide AA
R3710 VRS-CY1JF273FYJ 27k 1/16W Metal Oxide AA
R3716 VRS-TX2HF000JYJ 01/2WMetal Oxide AB
R3718 VRS-CE3AF821JYJ 820 1WMetal Oxide AC
R3721 VRS-CY1JF000JYJ 01/16W Metal Oxide AA
R3722 VRS-CY1JF000JYJ 01/16W Metal Oxide AA
R3724 VRS-CY1JF1R0JYJ 11/16W Metal Oxide AA
R3725 VRS-CY1JF000JYJ 01/16W Metal Oxide AA
R3726 VRS-TQ2BD683JY J 68k 1/8WMetal Oxide AA
R3727 VRS-CY1JF000JYJ 01/16W Metal Oxide AA
R3728 VRS-CY1JF393JYJ 39k 1/16W Metal Oxide AA
R3730 VRS-CY1JF223JYJ 22k 1/16W Metal Oxide AA
R3731 VRS-CY1JF222JYJ 2.2k 1/16W Metal Oxide AA
R3733 VRS-CY1JF102JYJ 1k1/16W Metal Oxide AA
R3734 VRS-CY1JF103FYJ 10k 1/16W Metal Oxide AA
R3735 VRS-CY1JF123FYJ 12k 1/16W Metal Oxide AA
R3736 VRS-CY1JF223FYJ 22k 1/16W Metal Oxide AA
R3737 VRS-CY1JF103JYJ 10k 1/16W Metal Oxide AA
R3738 VRS-CY1JF103FYJ 10k 1/16W Metal Oxide AA
R3739 VRS-CY1JF622FYJ 6.2k 1/16W Metal Oxide AA
R3740 VRS-CY1JF473FYJ 47k 1/16W Metal Oxide AA
R3741 VRS-CY1JF113FYJ 11k 1/16W Metal Oxide AA
R3742 VRS-CY1JF182FYJ 1.8k 1/16W Metal Oxide AA
R3743 VRS-CY1JF122FYJ 1.2k 1/16W Metal Oxide AA
R3745 VRS-CY1JF682FYJ 6.8k 1/16W Metal Oxide AA
R3746 VRS-CY1JF122FYJ 1.2k 1/16W Metal Oxide AA
R3749 VRS-CY1JF102JYJ 1k1/16W Metal Oxide AA
R3750 VRS-CY1JF391JYJ 390 1/16W Metal Oxide AA
R3751 VRS-TV1JD103JYJ 10k 1/16W Metal Oxide AA
R3752 VRS-CY1JF102JYJ 1k1/16W Metal Oxide AA
R3753 VRS-TX2HF000JYJ 01/2WMetal Oxide AB
R3759 VRS-TW2ED102JY J 1k1/4WMetal Oxide AA
R3761 VRS-CY1JF272JYJ 2.7k 1/16W Metal Oxide AA
R3762 VRS-TW2ED561JY J 560 1/4WMetal Oxide AA
R3766 VRS-CY1JF472JYJ 4.7k 1/16W Metal Oxide AA
R3901 VRS-TQ2BD000JY J 01/8WMetal Oxide AA
R3902 VRS-TQ2BD000JY J 01/8WMetal Oxide AA
å F3701 QFS-B2021GEZZJ Fuse, 2.0A/125VAD
å F3702 QFS-B1621GEZZJ Fuse, 2.0A/125VAD
R4005 VRS-CY1JF123JYJ 12k 1/16W Metal Oxide AA
R4006 VRS-CY1JF822JYJ 8.2k 1/16W Metal Oxide AA
R4011 VRS-CY1JF123JYJ 12k 1/16W Metal Oxide AA
R4012 VRS-CY1JF822JYJ 8.2k 1/16W Metal Oxide AA
R4021 VRS-CY1JF101JYJ 100 1/16W Metal Oxide AA
R4023 VRS-CY1JF472JYJ 4.7k 1/16W Metal Oxide AA
R4024 VRS-CY1JF471JYJ 470 1/16W Metal Oxide AA
R4029 VRS-CY1JF472JYJ 4.7k 1/16W Metal Oxide AA
R4030 VRS-CY1JF472JYJ 4.7k 1/16W Metal Oxide AA
å T6500 RTRNZ0805CEZZQ J TransformerAM
å T6501 RTRNZ0805CEZZQ J TransformerAM
å T6502 RTRNZ0805CEZZQ J TransformerAM
å T6503 RTRNZ0805CEZZQ J TransformerAM
R6500 VRS-TW2ED332JY J 3.3k 1/4WMetal Oxide AB
R6501 VRS-TW2ED332JY J 3.3k 1/4WMetal Oxide AB
R6502 VRS-CY1JF103JYJ 10k 1/16W Metal Oxide AA
R6503 VRS-CY1JF333JYJ 33k 1/16W Metal Oxide AA
R6504 VRS-TW2ED332JY J 3.3k 1/4WMetal Oxide AB
R6505 VRS-TW2ED332JY J 3.3k 1/4WMetal Oxide AB
R6506 VRS-CY1JF103JYJ 10k 1/16W Metal Oxide AA
R6507 VRS-CY1JF333JYJ 33k 1/16W Metal Oxide AA
MISCELLANEOUS PARTS
å F6500 QFS-B1621GEZZJ Fuse, 1.6A/125VAD
å F6501 QFS-B1621GEZZJ Fuse, 1.6A/125VAD
No part of this publication may be reproduced,
stored in a retrieval system, or transmitted in
any form or by any means, electronic, mechanical,
photocopying, recording, or otherwise, without
prior written permission of the publisher.
TQ1458-S
Jan. 2003 Printed in Japan
Design and Production Information
Design: Japan
Production : Japan
MI. KG
SHARP CORPORATION
AV Systems Group
Quality & Reliability Control Center
Yaita, Tochigi 329-2193, Japan
Loading...
+ hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.