Sharp DV-NC100SY Operating Manual

VCR/DVD COMBINATION
OPERATION MANUAL
Please read this Operation Manual carefully before using your VCR/DVD COMBINATION.
SHOWVIEW is a registered trademark of Gemstar Development Corporation. The SHOWVIEW system is manufactured under licence from Gemstar Development Corporation.
2
PULL OPEN
DV-NC100
OPERATE
OPEN/CLOSE
PLAYSTOP
DVDVCRCH
TIMER
RECPLAYREW FF
STOP/ EJECT
(TRACKING)
OUTPUT
The region number for this VCR/DVD is 2.
MODEL
DV-NC100S(Y)
SAFETY INFORMATION
DVD
DIGITAL
AUDIO OUT
ANALOG
AUDIO OUT
L
R
S-VIDEO
OUT
VCR AV2 (DECODER)
AV1 (TV)
DVD/VCR
AERIAL
RF OUT
COAXIAL
CLASS 1 LASER PRODUCT KLASSE 1 LASER PRODUKT KLASS 1 LASER APPARAT CLASSE 1 PRODUIT LASER
WARNING:
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS EQUIPMENT TO RAIN OR MOISTURE.
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, AND ANNOYING INTERFERENCE, USE THE RECOMMENDED ACCESSORIES ONLY.
TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS APPARATUS TO DRIPPING OR SPLASHING, NO OBJECTS FILLED WITH LIQUIDS, SUCH AS VASES, SHOULD BE PLACED ON THE APPARATUS.
Laser Diode Properties
Material: GaAs Wave length: DVD: 655 nm
CD: 790 nm Emission Duration: Continuous Laser output: Max. 0.8 mW
Power Cord Protection
To avoid any malfunctions of the VCR/DVD, and to protect against electric shock, fire or personal injury, please observe the following.
• Hold the plug firmly when connecting or disconnecting the AC power cord.
• Keep the AC power cord away from heating appliances.
• Never put any heavy object on the AC power cord.
• Do not attempt to repair or reconstruct the AC power cord in any way.
NOTE:
This VCR/DVD can be used only where the power supply is AC 220V-240V, 50Hz. It cannot be used elsewhere.
CAUTION:
USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF PROCEDURES OTHER THAN THOSE SPECIFIED HEREIN MAY RESULT IN HAZARDOUS RADIATION EXPOSURE.
AS THE LASER BEAM USED IN THIS VCR/DVD IS HARMFUL TO THE EYES, DO NOT ATTEMPT TO DISASSEMBLE THE CABINET. REFER SERVIC­ING TO QUALIFIED PERSONNEL ONLY.
• This VCR/DVD is classified as a CLASS 1 LASER product.
• The CLASS 1 LASER PRODUCT label is located on the rear cover.
• This product contains a low power laser device. To ensure continued safety, do not remove any cover or attempt to gain access to the inside of the product. Refer all servicing to qualified personnel.
–2–
EN
SAFETY INFORMATION
Location and Handling
• Do not cover or place the VCR/DVD in enclosed spaces to prevent excessive temperature build up.
• Do not place the VCR/DVD in direct sunlight, or near heat sources.
• Keep the VCR/DVD away from strong magnetic objects.
• Do not place any object containing water or other liquids on the VCR/DVD. In the event that liquid should enter the cabi­net, unplug the VCR/DVD immediately and contact the retailer or service centre approved by SHARP immediately.
• Do not remove the VCR/DVD cabinet. Touching parts inside the cabinet could result in electric shock and/ or damage to the VCR/DVD. For service and adjustment inside the cabi­net, call a qualified dealer or service centre approved by SHARP.
• Depending on the use environment, the temperature of the VCR/DVD may increase slightly.
tion.
This is not a malfunc-
Nonuse Periods
When the VCR/DVD is not being used, switch the VCR/DVD to the Standby mode. When left unused for a long period of time, the VCR/DVD should be unplugged from the household AC outlet.
No Fingers or Other Objects Inside
Do not put your fingers or objects on the disc tray or the cassette compartment.
Stacking
Place the VCR/DVD in a horizontal position, and do not place anything heavy on it.
Condensation
Moisture may form inside the VCR/DVD under the following conditions:
• immediately after a heater has been turned on.
• in a steamy or very humid room.
• when the VCR/DVD is suddenly moved from a cold environ­ment to a warm one.
If moisture forms inside this VCR/DVD, it may not operate properly or damage the video cassette. In this case, turn on the power and wait for more than two hours for the moisture to evaporate.
Cleaning
Unplug your VCR/DVD before cleaning. Use a damp cloth for cleaning. Do not use cleaning fluids or aerosols which could enter the VCR/DVD and cause damage, fire, or electrical shock. These substances may also deteriorate the finish of your VCR/DVD.
Auto Head Cleaning
• Automatically cleans video heads as you insert or remove a cassette, so you can see a clear picture.
• Playback picture may become blurred or interrupted while the TV program reception is clear. Dirt accumulated on the video heads after a long period of use, or the usage of rental or worn tapes can cause this problem. If a streaky or snowy picture appears during playback, the video heads in your DVD/VCR may need to be cleaned.
1. Please visit your local Audio/Video store and purchase a
good quality VHS Video Head Cleaner.
2. If a Video Head Cleaner does not solve the problem, please
refer any service to the nearest service centre approved by SHARP.
NOTES:
• Remember to read the instructions along with the video head cleaner before use.
• Clean video heads only when problems occur.
If there is Noise Interference on the TV While a Broadcast is being Received
Depending on the reception condition of the TV, interference may appear on the TV monitor while you watch a TV broad­cast and the VCR/DVD is left on. This is not a malfunction of the VCR/DVD or the TV. To watch a TV broadcast, turn off the VCR/DVD.
Service
Do not attempt to service this VCR/DVD yourself. Please refer any service to the nearest service centre approved by SHARP.
Copyright
Audio-visual material may consist of copyrighted works which must not be recorded without the authority of the owner of the copyright. Please refer to relevant law in your country.
Copy Protection
This VCR/DVD supports Macrovision copy protection. On DVDs that include a copy protection code, if the contents of the DVD are copied using a VCR, the copy protection code prevents the videotape copy from playing normally.
Apparatus Claims of U.S.Patent Nos. 4,631,603, 4,577,216, 4,819,098 and 4,907,093 licensed for limited viewing uses only.
This product incorporates copyright protection technology that is protected by method claims of certain U.S. patents and other intellectual property rights owned by Macrovision Corporation and other rights owners. Use of this copyright protection technology must be authorised by Macrovision Corporation, and is intended for home and other limited viewing uses only unless otherwise authorised by Macrovision Corporation. Reverse engineering or disas­sembly is prohibited.
Recommended Measures for Optimum Picture Excellence
The VCR/DVD is a precision device that is constructed using extremely accurate technology. Soiling or friction affecting the pickup lens or disc drive can impair the image quality. At the worst, neither video nor audio will be played back. Contact your authorised Sharp supplier for details.
Do not attempt to clean the pickup lens yourself.
–3–
EN
FEATURES
DVD
¡Dolby Digital sound
This VCR/DVD can handle Dolby Digital surround sound having 5.1 channels when connected to a Dolby Digital decoder.
¡Still/fast/slow/step playback ¡Rapid Play
Playback in slightly faster/ slower speed while keeping the sound quality as in the normal playback. Rapid Play is available only on discs recorded in the Dolby Digital format.
¡Random playback for audio CD, MP3, JPEG and
Kodak Picture CD
¡Programme playback for audio CD, MP3, JPEG
and Kodak Picture CD
¡DVD menus in a desired language ¡Screen saver
The screen saver programme starts when there is no input from the VCR/DVD for 5 minutes in the stop mode.
¡Subtitles in a desired language ¡Selecting a camera angle ¡Choices for audio language and sound mode ¡Parental lock ¡Automatic detection of discs
This VCR/DVD automatically detects if a loaded disc is DVD, audio CD, video CD, MP3 and JPEG on disc or Kodak Picture CD.
¡Playing an MP3 disc ¡Displaying a JPEG picture
Kodak Picture CDs can be played. Still images stored in JPEG format on CD-RW/R can also be played.
¡Direct Search ¡DTS (Digital Theater System)
You can enjoy 5.1 channel surround sound system devel­oped by Digital Theater System, Inc. which reproduces the original sound as truthfully as possible. External decoder is required.
¡On-screen display
Information about the current operation can be displayed on a TV screen, allowing you to confirm the currently active functions (such as programme playback), on the TV screen using the remote control.
¡MPEG audio
This VCR/DVD can handle a disc that supports MPEG audio when it is connected to a MPEG decoder.
¡Search
Chapter search / Title search / Track search / Time search
¡Repeat
Chapter / Title / Track / Group / All / A-B
¡Zoom ¡Marker
The part designated by user can be called back.
¡Resume Play ¡Virtual Surround ¡Bit rate indication ¡DRC (Dynamic range control)
You can control the range of sound volume.
¡Digital Gamma Setting ¡Video Out
When playing an NTSC disc, select either PAL or AUTO(NTSC) correspondingly to your TV system.
VCR
¡Auto Head Cleaner ¡6 Head Hi-Fi Stereo ¡On screen Display ¡Auto power on system
Automatically turns the VCR on when you insert the cas­sette.
¡Digital Auto Tracking (DTR) ¡Auto Repeat ¡Index Search ¡Time Search ¡Quick-Find ¡NTSC Playback ¡1 Year, 8 events (including Daily and Weekly
Timer Recording)
¡OTR (One Touch Recording) ¡VPS (Video Programme System) /
PDC (Programme Delivery Control)
“Kodak Picture CD of Eastman Kodak Company.
COMPATIBLE
” is a trademark
INTRODUCTION
Symbols Used in this Manual
The following symbols appear below in some headings and notes in this manual, with the following meanings:
DVD
:Description refers to playback of DVD video discs. (includ-
ing DVD-RW/R and DVD+RW/R discs (Video mode only))
CD
:Description refers to playback of audio CDs.
/
VCDVCD
:Description refers to playback of video CDs.
without PBC function
MP3
:Description refers to playback of MP3 discs.
DVD-RW
VR mode
: Description refers to playback of the VR mode (Video
Recording format).
*The VR mode (Video Recording format) is a recording
mode to enjoy editing the programme or “manual mode” for recording in desired resolution and time.
JPEG
: Description refers to viewing of JPEG discs.
(QUICK)
: Basic setup can be performed more quickly by selecting
(QUICK setup menu).
–4–
INTRODUCTION
Supplied Accessories
• Remote control
• Two R-6 batteries
• Operation Manual
• Round coaxial cable
Manufactured under license from Dolby Laboratories. “Dolby” and the double-D symbol are trademarks of Dolby Laboratories.
TABLE OF CONTENTS
SAFETY INFORMATION. . . . . . . . . . . . . . . . . . . . . . . . 2
FEATURES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Symbols Used in this Manual. . . . . . . . . . . . . . . . . . . . . 4
Supplied Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . 5
ABOUT THE DISCS . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Playable Discs. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Disc Types . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
FUNCTIONAL OVERVIEW . . . . . . . . . . . . . . . . . . . . . . 7
FRONT PANEL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
REAR VIEW . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
REMOTE CONTROL . . . . . . . . . . . . . . . . . . . . . . . . . 8
Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Displays During Operation . . . . . . . . . . . . . . . . . . . . . . . 9
Loading the Batteries. . . . . . . . . . . . . . . . . . . . . . . . . . . 9
SETTING UP YOUR VCR/DVD COMBINATION . . . . . . 10
Connecting to a TV or a stereo TV . . . . . . . . . . . . . . . . 10
Connecting to a TV Equipped with S-VIDEO Input Jack
Connecting to Audio Equipment. . . . . . . . . . . . . . . . . . 11
Playing 2 channel audio . . . . . . . . . . . . . . . . . . . . . . 11
Playing Dolby Digital (5.1 channel), DTS
or MPEG audio . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
VCR/DVD SET UP. . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Tuning on Your VCR/DVD. . . . . . . . . . . . . . . . . . . . . . . 12
Changing the Language. . . . . . . . . . . . . . . . . . . . . . . . 12
Video Channel Setting . . . . . . . . . . . . . . . . . . . . . . . . . 12
Setting the Clock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Channel Presetting . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Automatic Channel Preset . . . . . . . . . . . . . . . . . . . . . . 13
Manual Channel Preset . . . . . . . . . . . . . . . . . . . . . . . . 13
To Skip a Preset Channel . . . . . . . . . . . . . . . . . . . . . . 14
Channel Reprogramming . . . . . . . . . . . . . . . . . . . . . . . 14
VCR OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
VCR Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Playback . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Recording . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Hi-Fi Stereo Sound System . . . . . . . . . . . . . . . . . . . . . 15
OTR (One Touch Recording) . . . . . . . . . . . . . . . . . . . . 15
Auto Repeat Playback . . . . . . . . . . . . . . . . . . . . . . . . . 16
Picture Select . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Automatic Operation . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Real Time Tape Counter . . . . . . . . . . . . . . . . . . . . . . . 16
Timer Recording . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
SHOWVIEW®Guide Channel Set . . . . . . . . . . . . . . . . . . 17
Timer Recording Using the SHOWVIEW System . . . . . . . 17
Auto Return . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
VPS/PDC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Quick-Find. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Index Search . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Time Search . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Recording from DVD to VCR . . . . . . . . . . . . . . . . . . . . 19
Copying a Video Tape . . . . . . . . . . . . . . . . . . . . . . . . . 19
. . 10
“DTS” and “DTS Digital Out” are trademarks of Digital Theater Systems, Inc.
Status Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Video Cassette Tape . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Tw o Different Tape Speeds . . . . . . . . . . . . . . . . . . . . 19
TV Colour System . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
PLAYING A DISC . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Basic Playback . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
General Features. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Pause . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Disc Menus . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Title Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Step by Step Playback. . . . . . . . . . . . . . . . . . . . . . . . . 21
Rapid Play. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Resume. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Playing the disc recorded in VR mode
(Video Recording format). . . . . . . . . . . . . . . . . . . . . . . 21
Fast Forward / Reverse Search . . . . . . . . . . . . . . . . . . 22
Slow Forward / Reverse. . . . . . . . . . . . . . . . . . . . . . . . 22
Zoom. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Tr ack Search . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Title / Chapter Search . . . . . . . . . . . . . . . . . . . . . . . . . 22
Time Search . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Repeat . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
A-B REPEAT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Programme (CD) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Random Playback (CD) . . . . . . . . . . . . . . . . . . . . . . . . 24
MP3 / JPEG Playback . . . . . . . . . . . . . . . . . . . . . . . . . 24
Kodak Picture CD . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Slide Show Mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Programme (MP3/JPEG) . . . . . . . . . . . . . . . . . . . . . . . 25
Random Playback (MP3/JPEG) . . . . . . . . . . . . . . . . . . 25
Stereo Sound Mode. . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Audio Language . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Subtitle Language . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Camera Angle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Changing the On-Screen Display . . . . . . . . . . . . . . . . . 26
Marker Setup Screen. . . . . . . . . . . . . . . . . . . . . . . . . . 27
Digital Gamma Setting. . . . . . . . . . . . . . . . . . . . . . . . . 27
Virtual Surround . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
DVD SETUP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Audio Setting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Parental Control. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
PARENTAL LEVEL. . . . . . . . . . . . . . . . . . . . . . . . . . 28
IF YOU FORGET THE PASSWORD . . . . . . . . . . . . . 28
PARENTAL CONTROL LEVELS. . . . . . . . . . . . . . . . 28
Display Setting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Language Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Returning all selections of SETUP
(except for PARENTAL) to their default settings . . . . . . 29
TROUBLESHOOTING GUIDE. . . . . . . . . . . . . . . . . . . 30
SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
MAINTENANCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
–5–
EN
ABOUT THE DISCS
Example
Group 1 Group 2
Tra c k 1 Track 2Track 5Track 6Tra c k 3 Track 4
Example
Tra c k 1 Track 2 Track 3 Track 4 Track 5 Track 6
Example
Title 1 Title 2
Chapter 1 Chapter 2 Chapter 1 Chapter 2Chapter 3 Chapter 4
2
Playable Discs
The following discs can be played back on this VCR/DVD.
¡
DVD video ¡DVD-RW/R* ¡DVD+RW/R* ¡Audio CD ¡CD-RW/R* ¡MP3* ¡Video CD ¡JPEG*
¡
Kodak Picture CD
*
Depending on the types or the writing method of the medium some discs cannot be played. For DVD+RW/R, only discs recorded in the Video mode can be played back.
• Some DVD-RW/R, DVD+RW/R or CD-RW/R discs made on personal computers, or on DVD recorders may not be played back prop­erly due to the factors such as scratches, dirt or special properties of the disc. Discs made on personal computers may not playback properly due to compatibility or settings in the recording software. We recommend
• always to use the standard settings and correctly formatted discs. (Please contact the software supplier for more details.)
You can play back discs which bear the marks on page 31. If you use nonstandardized discs, this unit may not play them back. Even if they are played back, the sound or video quality will be compromised.
This VCR/DVD cannot record a copy protected DVD and CD!
This VCR/DVD conforms to the PAL colour system. Also you can play discs recorded with the NTSC system via a PAL system TV set.
• Some discs include region codes as shown below.
• The number inside the symbol refers to a region of the world, and a disc encoded in a specific region format can only be played back on DVD players with the same region code.
:This label indicates playback compatibility with DVD-RW discs recorded in VR mode (Video Recording Format).
NOTE
• This VCR/DVD cannot play the DVD-RW that supports CPRM (Contents Protection for Recordable Media).
ABOUT THE PBC FUNCTION OF VIDEO CD
This unit conforms to ver.1.1 and ver.2.0 of VIDEO CD standard, with PBC function. Ver.1.1 (without PBC function): You can enjoy playback picture as well as music CD. Ver.2.0 (with PBC function): When using a VIDEO CD with PBC function, “PBC” appears on the display.
What is PBC? “PBC” stands for the PlayBack Control.You can play interactive software using a menu screens. Refer to instructions of VIDEO CD.
For Customer Use: Read carefully the information located at the bottom of your VCR/DVD and enter below the Serial No.Retain this information for future reference. Model No.: VCR/DVD COMBINATION: DV-NC100S Serial No.: __________________________
The following discs cannot be played back on this VCR/DVD:
¡
DVD with region codes other than 2 or ALL.¡DVD-ROM
¡
DVD-RAM (Never play back, otherwise malfunction may result.)
¡
CD-ROM ¡CDV (Only plays back the audio part.)
¡
CD-G (Only plays back the sound.) ¡CD-I (Never play back, otherwise malfunction may result.)
¡
Super Audio CD (Only the sound recorded on the normal CD layer can be delivered. The sound record­ed on the high density Super Audio CD layer cannot be delivered.)
¡
Photo CD (Never play back, otherwise malfunction may result.)
Any other discs without compatibility indications.
Disc Types
[DVD]
Data on a DVD is divided into sections called “titles”, and then into subsections called “chapters”, each of which is given a title or chapter number. Playback condi­tions are preset on some DVD video discs, and these playback conditions take priority over user operations on this VCR/DVD. If a function you selected do not run as desired, refer to the manual accompanying the disc.
[Audio CD / Video CD]
Data on an audio CD or a video CD is divided into sections called “tracks”, each of which is given a track number.
[MP3/JPEG]
Data on an MP3 and JPEG discs are divided into sections called “groups”, and then into subsections called “tracks”, each of which is given a group or track number.
6–
EN
FUNCTIONAL OVERVIEW
FRONT PANEL
1
DV-NC100
OPERATE
2
3
OPEN/CLOSE
4 5
6
PULL OPEN
20 19
STOP/
TIMER
RECPLAYREW FF
EJECT
16
1718
13
14
15
1. OPERATE
To turn the unit ON or OFF. The indicator is on when this unit is turned on.
2. Cassette Compartment
3. OPEN/CLOSE (DVD)
To open or close the disc tray.
4. VCR OUTPUT indicator
The indicator is on when this unit is in the VCR mode. Make sure that this indicator is on before VCR opera­tion.
5. DVD OUTPUT indicator
The indicator is on when this unit is in the DVD mode. Make sure that this indicator is on before using the DVD player.
6. Disc tray
7. PLAY (DVD)
To begin disc playback.
8. STOP (DVD)
To stop playback.
9. OUTPUT
To select the DVD mode or VCR mode.
10. CHANNEL
To change TV channels. To adjust the tracking manually during VCR playback
11. Display
OUTPUT
DVDVCRCH
(TRACKING)
12
11
10
9
PLAYSTOP
8 7
12. Remote Sensor
13. TIMER indicator
The indicator is on when the VCR/DVD is in standby mode for a timer recording or during a One Touch Recording.
14. REC (VCR)
Press once to start recording or repeatedly to start One Touch Recording. The indicator is on during recording.
15. PLAY (VCR)
To begin tape playback
16. STOP/EJECT (VCR)
To stop playback. To eject the tape in the Stop mode.
17. FF (VCR)
To fast forward the tape.
18. REW (VCR)
To rewind the tape.
19. AUDIO IN AV3 jacks (VCR Only)
Connect audio cables coming from the audio out jacks of a camcorder, another VCR, or an audio source here.
20. VIDEO IN AV3 jack (VCR Only)
Connect a cable coming from the video out jack of a camcorder, another VCR or an audio-visual source (laser disc player, video disc player, etc.) here.
REAR VIEW
DVD
DIGITAL
ANALOG
AUDIO OUT
S-VIDEO
OUT
L
R
VCR AV2 (DECODER)
DVD/VCR
AUDIO OUT
COAXIAL
21. MAIN (AC power cord)
Connect to a standard AC plug.
22. COAXIAL DIGITAL AUDIO OUT jack (DVD Only)
Connect to a compatible Dolby Digital receiver. Use to connect to a Dolby Digital decoder, DTS decoder or MPEG decoder.
23. AUDIO OUT jack (ANALOG Left/Right) (DVD Only)
Connect to the Audio input jacks of A/V-compatible TV
24. S-VIDEO OUT jack (DVD Only)
Use the S-Video cable to connect this jack to the S­Video jack on your A/V-compatible TV or wide screen TV for a higher quality picture.
AV1 (TV)
25. EURO AV1 (TV) OUT terminal
Use the scart cable to connect this terminal to the 21 pin scart terminal on your A/V-compatible TV or wide screen TV for a best quality picture.
26. EURO AV2 (DECODER) terminal (VCR Only)
Use the scart cable to connect this terminal to the 21 pin scart terminal on your decoder.
27. RF OUT jack
Use the supplied round coaxial cable to connect this jack to the ANTENNA IN jack on your TV.
28. AERIAL jack
Connect your antenna, Cable Box, or Direct Broadcast System.
–7–
AERIAL
RF OUT
27 2825 2624232221
EN
FUNCTIONAL OVERVIEW
REMOTE CONTROL
1. DISPLAY Button
Press to display the current playback mode.(DVD)
Press to display the current time, tape counter and channel number.(VCR)
2. OPERATE Button
Press to turn the power on and off.
3. ANGLE/SHOWVIEW Button
Press to change the camera angle to see the sequence being played back from a different angle.(DVD) Press to programme timer recording with the S system. (VCR)
4. SUBTITLE Button
Press to select a desired subtitle language or to change the Panel Display settings. (DVD)
5. ZOOM Button
Enlarges part of a DVD-reproduced image.
6. VCR Button
Press to select VCR output mode and to use the remote control in VCR mode.
7. TITLE Button
Displays the title menu.
8. ARROW Buttons (opsB)
(up/down/left/right) Press to select an item in the menu and to move the cursor.
9. RETURN Button
Returns to the previous operation.(DVD)
10. Numerical Buttons
11. CLEAR/C-RESET Button
Press to clear the markers or the incorrect input. (DVD)
Press to reset the counter. (VCR)
12. PLAY Button
Press to begin playback.
13. REV Button
Fast reverse playback to a desired point.
14. REC/OTR Button
Press once to start recording or repeatedly to start One Touch Recording. (VCR)
15. STOP Button
Press to stop playback. (DVD)
Press to stop playback or recording. (VCR)
16. DIRECT SKIP/QUICK-FIND Button
Press to locate a desired point. (DVD)
Press to skip to the beginning of the next programme.
(VCR)
17. TAPE SPEED Button
Press to select the VCR’s recording speed. (SP or LP)
18. GAMMA Button
Press to adjust the black parts of the picture brighter. (DVD)
19. SEARCH MODE Button
Press to call up the index or time search menu. (VCR)
20. CH (o/p) Button
Press to change TV channels or to adjust the tracking manual on the VCR.
21. TIMER ON/OFF Button
Press to put the VCR into standby mode for a timer recording.
22. SLOW Button
Press to view the video tape in slow motion.
23. STILL/PAUSE Button
• Press to pause playback or to advance playback one
frame at a time. (DVD)
• Press to pause playback or recording or to advance
playback one frame at a time. (VCR)
24. FWD Button
• Fast forwards playback to a desired point.
HOWVIEW
136
OPERATE
2 3
SUBTITLE
4
5 6
7 8
9
ZOOM
RETURN
1 2 3
10
11 12
7
CLEAR/C-RESET
REV
13
14
15
DIRECT SKIP
16
18
QUICK-FIND
17
GAMMA
19
25. DAILY/WEEKLY Button
Press to select once, daily, everyday, or weekly when you programme the automatic timer recording using the SHOWVIEW system. (VCR)
26. SKIP (G / H) Buttons
Press to skip Chapters or Tracks. (DVD)
27. A-B REPEAT Button
Repeats playback of a selected section. (DVD)
28. REPEAT Button
Repeats playback of the current disc, title, chapter or track. (DVD)
29. ENTER Button
Press to accept a setting. (DVD)
30. MENU Button
Press to display the DVD menus and MP3 file lists.
(DVD)
Press to display the VCR menu. (VCR)
31. DVD Button
Press to select DVD output mode and to use the remote control in DVD mode
32. MODE Button
Activates programme playback or random playback mode. (CD/ MP3/ JPEG) Activates the 3D sound or Rapid Play. (DVD)
33. MARKER Button
Press to call back the Marker display. (DVD)
34. AUDIO Button
Press to select a desired audio language or sound mode. (DVD)
Press to select a desired sound mode. (VCR)
35. OPEN/CLOSE/EJECT Button
Press to insert discs into or remove them from the tray.
(DVD)
Press to remove the tape from the VCR. (VCR)
36. SETUP Button
Press to enter the setup mode or to change setup items. (DVD)
–8–
OPEN/CLOSE
SETUP
DISPLAY
ANGLE
AUDIO
SHOWVIEW
VCR
DVD
6
54
8 9
DAILY/WEEKLY
+10
0
PLAY
STILL/PAUSEREC/OTR
STOP
TAPE
TIMER
SPEED
ON/OFF
SEARCH MODE
VCR/DVD COMBINATION
CH
TM
NA526ED
EJECT
MARKER
MODE
MENUTITLE
ENTER
REPEAT
A-B REPEAT
FWD
SLOW
SKIP
35
34
33
32
31
30
29
28
27
26
25
24
23
22
21
20
EN
FUNCTIONAL OVERVIEW
Lights up when the inserted disc is being played back.
Displays a type of the disc which is inserted on the tray.
• DVD : DVD
• CD : Audio CD, MP3, JPEG, Kodak Picture CD
• VCD : Video CD
Lights up when the A-B repeat function is on.
Lights up when the repeat function is on.
GROUP
DVD
VCD
Lights up when the ALL repeat function is on.
Lights up when playing back in slow mode. (DVD or Video CD)
Lights up when the inserted disc comes to a pause.
Displays the elapsed time of the title or track. The number of a new title, chapter, or track is displayed when a chapter or track is switched.
No disc inserted or cannot read
Tr ay open
Tr ay closed
Loading the Disc
Lights up when the playback control is activated.
Display
DVD output mode
Displays During Operation
DVD
VCR output mode
*Lights up when a tape
is inserted.
Lights up during playback when the repeat function is on.
Lights up when the playback is in still or slow mode.
Lights up when the inserted tape is being played back.
* , and mark will disappear when you set VCR/DVD in DVD mode. However, the function indicated by each mark is still working.
REC
Loading the Batteries
1. Open the battery compartment cover.
2. Insert two R-6 batteries, with each one oriented correctly.
*Lights up when the timer recording
or an OTR recording has been set.
REC
Works as a tape counter (hour, minute, second). Also displays a channel number, tape speed, remaining time for OTR
*Lights up
during a recording. Flashes when a recording is paused.
–9–
3. Close the cover.
NOTES:
• Do not mix alkaline and manganese batteries.
• Do not mix old and new batteries.
EN
TV (with external input jacks)
RL
AUDIO
IN
DVD
DIGITAL
AUDIO OUT
ANALOG
AUDIO OUT
S-VIDEO
OUT
L
R
VCR AV2 (DECODER)
AV1 (TV)
DVD/VCR
AERIAL
RF OUT
S-VIDEO
INPUT
AUDIO cable
(commercially available)
S-VIDEO cable (commercially available)
To ANALOG
AUDIO OUT jacks
To S-VIDEO
OUT jack
(White)
(Red)
(White)
To AUDIO input
jacks
To S-VIDEO
input jack
(Red)
SETTING UP YOUR VCR/DVD COMBINATION
To AERIAL
jack
To SCART
terminal
Round coaxial cable
(supplied)
Scart cable
(commercially available)
from Antenna
DVD
DIGITAL
AUDIO OUT
ANALOG
AUDIO OUT
S-VIDEO
OUT
L
R
VCR AV2 (DECODER)
AV1 (TV)
DVD/VCR
AERIAL
RF OUT
(TV)
To RF OUT
jack
To EURO AV1(TV)
OUT terminal
VCR/DVD
VCR
TV
CAUTION:
• Be sure to turn off the VCR/DVD and equipment to be connected before connecting.
• Read through the operation manual for the equipment to be connected.
• Be sure to keep the VCR/DVD connection cables separate from the TV antenna cable when you install the VCR/DVD, because it may cause electrical interference when you are watching television programmes.
• DTS audio cannot be produced with an analogue connection.
Connecting to a TV or a stereo TV
CAUTION:
• Connect the VCR/DVD directly to the TV. Do not connect the VCR/DVD to a VCR, then connect the VCR to the TV. Copyright protection in the VCR could distort the picture playing on the VCR/DVD.
Connecting to a TV Equipped with S-VIDEO Input Jack (DVD only)
If your TV has no SCART input terminal but has an S-VIDEO input jack, use a commercially available S-VIDEO cable to con­nect from the VCR/DVD to the TV.
• You will not be able to hear all of the sound being output by the VCR/DVD if you use the AUDIO cable (commercially avail­able) to a monaural TV that has only one AUDIO input jack.
NOTES:
• Be sure that the colours of the jacks and plugs match up when connecting the cable.
• Connect the VCR/DVD directly to the TV. If you attempt to view video on a TV connected via a VCR, the copy protection function will scramble the picture.
• If you want to listen to the audio through audio equipment, connect only the S-VIDEO cable to the TV.
• You will still need the scart cable or Round coaxial cable for VCR features. (S-VIDEO connection is available only in DVD mode.)
–10–
EN
SETTING UP YOUR VCR/DVD COMBINATION
DVD
DIGITAL
AUDIO OUT
ANALOG
AUDIO OUT
S-VIDEO
OUT
L
R
VCR AV2 (DECODER)
AV1 (TV)
DVD/VCR
AERIAL
RF OUT
ANALOG INPUT
R
L
Amplifier of stereo system, etc.
Audio cable
(commercially
available)
(Red)
(White)
(Red)
(White)
Jack and Plug Colours
To amplifier audio input jacks
Audio Left: White Audio Right: Red
To AUDIO OUT jacks
COAXIAL
DIGITAL IN
DVD
DIGITAL
AUDIO OUT
ANALOG
AUDIO OUT
S-VIDEO
OUT
COAXIAL
L
R
VCR AV2 (DECODER)
AV1 (TV)
DVD/VCR
AERIAL
RF OUT
Coaxial digital cable (commercially available)
To coaxial digital
input jack
To COAXIAL
DIGITAL AUDIO
OUT jack
Audio equipment with coaxial digital input jack
Connecting to Audio Equipment
Connecting the VCR/DVD to audio equipment provides normal stereo sound, plus powerful stereo sound enhanced by Dolby Digital 5.1 channel surround sound, DTS, and MPEG Audio.
Playing 2 channel audio
CC
Analogue audio connection
CC
Digital audio connection
You can make this connection using a coaxial digital cable.
Digital Connection to an MD to Record a CD
Some Audio CDs have a short silent section between musical tracks. When sound from discs such as these is digitally recorded by connecting the VCR/DVD directly to a digital recorder (such as an MD recorder), the music may be recorded con­tinuously and track numbers may be lost.
CC
Digital Connection to Audio Equipment or MD Recorder without a Dolby Digital Decoder
• Audio CD Audio CDs can be transferred digitally to other equipment such as an MD recorder, play the disc as you would normally with
the audio mode set to “L+R” and use the connection shown above. Audio CDs recorded in the DTS format cannot be trans­ferred digitally or via analogue.
•DVD DVDs recorded in Dolby Digital 5.1 channel surround sound, DTS or MPEG Audio cannot be connected digitally to external
recording equipment such as an MD recorder. The audio source on a disc in a Dolby Digital 5.1 channel surround format cannot be recorded as digital sound by an MD
recorder. It may be possible to record “DOLBY DIGITAL” or MPEG Audio via a digital connection if the VCR/DVD output is set to “DPCM” (Refer to page 27 “Audio Settings”). Analogue recording is possible but not for DTS recorded audio.
–11–
EN
SETTING UP YOUR VCR/DVD COMBINATION
DIGITAL IN
COAXIAL
To coaxial digital
input jack
Coaxial digital cable (commercially available)
Dolby Digital (5.1 ch) / DTS / MPEG Audio processor or amplifier
DVD
DIGITAL
AUDIO OUT
ANALOG
AUDIO OUT
S-VIDEO
OUT
COAXIAL
L
R
VCR AV2 (DECODER)
AV1 (TV)
DVD/VCR
AERIAL
RF OUT
To COAXIAL
DIGITAL AUDIO
OUT jack
Playing Dolby Digital (5.1 channel), DTS or MPEG audio
Connecting an amplifier with a Dolby Digital/ DTS/ MPEG Audio digital surround processor to your VCR/DVD’s coaxial digital jack provides richer and more powerful audio play.
CC
Digital connection to a processor or amplifier with a coaxial digital input jack
You can make this connection using a coaxial digital cable.
NOTES:
• This connection is not possible if the processor or amplifier to which you want to connect does not have a coaxial digital input jack.
• ANALOG AUDIO OUT and AV (TV) of the VCR/DVD are not available on the DTS audio.
VCR/DVD SET UP
Turning on Your VCR/DVD
The following steps should only be performed if there is a power failure or if this unit is unplugged for more than 1 hour.
1
Tu rn on the TV and select the video channel on the TV.
2
Press
OPERATE, then VCR.
3 4
K or L repeatedly to select your desired language.
Press
MENU.
Press
Changing the Language
1
Press VCR, then MENU.
2
Press
K or L to select INITIAL, then press B.
3 4
K or L to select LANGUAGE, then press B.
Press
K or L repeatedly to select your desired language,
Press and
MENU to confirm.
Video Channel Setting
Video Channel setting will be necessary, if your VCR/DVD is connected to the TV via the round coaxial cable.
1
Press
VCR.
2
Insert a pre-recorded tape into the cassette compart-
ment. Playback will start automatically. If playback does not start, press PLAY.
3
Select and adjust your TV to channel 36.
• If the playback picture appears on the TV screen, con-
tinue with step .
9
• If channel 36 is set for broadcasting, or interference lines appear on the picture, the RF converter must be set to a different channel between CH22 and CH69.
Continue with step .
4
NOTES:
–12–
4
Press MENU.
5
Press K or L repeatedly to select INITIAL, then press B.
6
Press K or L repeatedly to select RF OUT, then press B. The RF OUT CH menu will appear.
7
Press K or L to select a channel which is not used for broadcasted between channel 22 and channel 69 in your area, and
8
Press
B to confirm.
MENU to exit. Set the TV channel to the RF OUT CHANNEL which was selected on the VCR/DVD. A picture from the VCR/DVD will appear on the TV screen. If a picture does not
appear, repeat steps to using a different channel
84
which is not used for broadcasting.
9
STOP to stop the tape.
Press
• You may also access the RF OUT CH menu by pressing and holding MENU on the remote control for 3 seconds during power off until the RF OUT CH menu appears.
• If this unit and your TV are connected using a SCART cable, the RF converter may be switched off to avoid any possibility of interference. To switch off the RF converter, follow steps and to above and press Lrepeat-
641
edly until “--” appears next to RF OUT CH. Press B, then press MENU to exit.
EN
VCR/DVD SET UP
Channel Plan
CH Indication TV Channel
02 – 12 E2 – E12 13 – 20 A – H (only ITALY) 21 – 69 E21 – E69 74 – 78 X, Y, Z, Z+1, Z+2 80 – 99,100 S1 – S20,GAP 121 – 141 S21 – S41
This VCR/DVD can receive Hyper and Oscar frequency bands.
Setting the Clock
This VCR/DVD incorporates a 24-hour clock. The clock must be set for the Timer Recording function to operate correctly.
1
Press VCR, then MENU.
2
Press K or L to select INITIAL, then press B.
3
Press K or L to select CLOCK, then press B.
4
Press K or L to select MANUAL or AUTO, then press B.
• If you select MANUAL, continue with step .
• If you select AUTO, Auto Clock Setting becomes ON. The clock time will appear automatically when you next turn the VCR mode off and on.
5
Press K or L until the relevant year appears, then press B.
6
Press
K or L until the relevant month appears, then
press B.
7
Press K or L until the relevant day appears, then press B.
8
Press K or L until the relevant hour appears, then press B.
9
Press K or L until the relevant minute appears.
10
Press MENU to start the clock.
NOTES:
• Press s to go one step back from the current step during steps to .
• Although seconds are not displayed, they begin count­ing from 00 when you exit by pressing the MENU. Use this feature to synchronise the clock with the correct time.
• If this unit is unplugged or if there is a power failure for more than 1 hour, you may have to reset the clock.
Auto Clock
Channel Presetting must be set before the Auto Clock is set.
• To set the clock automatically, the channel assigned to position 01 must have the PDC signal.
• The clock cannot be set automatically if you are not receiv­ing a channel that carries a time signal in your area. In this case, set the clock manually.
• Once the auto clock setting is performed, the VCR/DVD will correct the current time by receiving VPS/PDC broad­casts whenever you turn off the VCR/DVD.
• The VCR/DVD will correct the current time automatically at 8:00, if the VCR/DVD power is turned off.
• Between 23:00~1:00, the AUTO CLOCK function does not work even if the VCR/DVD power is turned off.
95
Channel Presetting
Tuning of broadcast channels not already preset in the VCR/DVD can be performed in two ways.
Automatic Channel Preset
• By “AUTOMATICALLY” tuning channels and placing them in sequential order in the VCR/DVD’s memory i.e. the first channel found will be memorised into the VCR/DVD’s channel position 1, the second channel found will be mem­orised into the VCR/DVD’s channel position 2 and so on.
• Execution of the “Automatic” Channel presetting cancels all the preset channels. DO NOT use this feature if you intend to use some of the pre-tuned channels. Use the “Manual” channel presetting function to tune in the additional chan­nels you require.
Manual Channel Preset
Each channel is tuned manually and individually. Follow the steps laid out in the “Manual Channel Preset”.
Before you preset Channel...
• It is necessary to set the video channel if your VCR/DVD is connected to the TV via the round coaxial cable, and TV channel 36 is set for broadcasting, or interference lines appear on the picture. Please refer to “Video Channel Setting”.
Automatic Channel Preset
You can programme the tuner to scan all the channels you can receive in your area.
1
Tu rn on the TV and select the TV channel to the video channel on the TV.
2
Press
5
3 4 5
To select a desired channel
You can select a desired channel by using CH (oo/pp), or directly pressing the numerical buttons on the remote con­trol.
• Enter a channel numbers as a two-digit number for the quickest results. For example, to select channel 6, press 0 and 6. If you only press 6, channel 6 will be selected after a brief delay.
• You can only select channels 1–99.
VCR, then MENU. Press K or L to select INITIAL, then press B. Press K or L to select CH TUNING, then press B. Press K or L to select AUTO, then press B.
• The tuner scans and memorises all the active channels in your area. After scanning, the tuner stops on the lowest memorised channel.
Manual Channel Preset
1
Press VCR, then MENU.
2
Press K or L to select INITIAL, then press B.
3
Press K or L to select CH TUNING, then press B.
4
Press K or L to select MANUAL, then press B.
5
Press K or L to select POSITION, then press B.
• When a weak signal is received in Manual Tuning mode, you can change the background to solid blue or the static screen by pressing the CLEAR/C-RESET.
–13–
6
Press the position number, then press B.
• You can select position number 01-99.
• If ON appears on the right side of SKIP, press K or L
• If you want to remove scrambled signals, press K or L
7
Press K or L to select CHANNEL, then press B. Press K or L. The VCR/DVD tuner will begin to search up or down automatically. When a channel is found, the VCR/DVD will stop searching and the picture will appear on the TV Screen.
• You can select desired channel number by using the
• If this is the channel you want, press B.
8
Press MENU to exit.
NOTE:
• To confirm that a channel has been added, press CH
numerical buttons,K or L to select your desired
to point to SKIP. Then press B to select OFF.
repeatedly to point to DECODER. Then, press B to select ON.
numerical buttons. You must refer to the following Channel Plan table and press three digits to select the channel number. (To select channel 24, first press “0” button and then press “2” and “4”).
oo/pp
).
(
EN
VCR/DVD SET UP
To Skip a Preset Channel
The channels you can no longer receive or seldom watch can be set to be skipped when you access channels with
CH (oo/pp).
1
Press
2 3 4 5 6
7
8
NOTE:
VCR, then MENU.
Press K or L to select INITIAL, then press B. Press K or L to select CH TUNING, then press B. Press K or L to select MANUAL, then press B.
Press K or L to select POSITION, then press B. Press the numerical buttons,KorLto select relevant po­sition number, then press B. Press K or L to select SKIP, then press B to select [ON].
• To memorise the channel again, press B. ON will change to OFF.
Press MENU to exit.
• To confirm that a channel has been deleted, press CH
(oo/pp).
VCR OPERATION
VCR Features
Ensure that all VCR setting begins in VCR mode by pressing
VCR. (Make sure that the VCR OUTPUT indicator is lit.)
Playback
Tracking Adjustment
• Tracking adjustment will be activated automatically (Digital Tr acking function) when you start playback.
• When playing pre-recorded tapes or tapes recorded on
units other than your own, noise lines (black and white streaks) may appear on the playback picture. If this occurs, you can adjust the tracking control manually by pressing CH (oo/pp) until the streaks disappear. To return to the DTR function, stop the tape once and start playback again.
• You can reduce the noise lines by pressing CH (oo/pp) in Slow mode, too. Slow tracking adjustment is not set auto­matically.
• In the Still mode, press the streaks disappear. To return to the Still mode, press the
STILL/PAUSE again.
1
Tu rn on the TV and select the video channel on the TV.
2
Insert a prerecorded tape. The VCR/DVD will turn on automatically. If the erase-pro­tection tab has been removed, the VCR mode will start playback automatically.
• If the VCR/DVD power was already on, press switch to VCR mode.
3
If playback does not start automatically, press press PLAY to begin playback.
•Tracking adjustment will be activated automatically (Digital Tracking function) when you start playback. To adjust the tracking manually, press CH (oo/pp). <If a tape is already in the VCR/DVD...>
• Using the b
Just press PLAY on the VCR/DVD. Power will auto- matically turn on and playback will start. (Direct Button Operation)
• Using the b
Press OPERATE to turn on, and then press PLAY.
4
Press STOP to stop playback.
•To remove the tape, press EJECT.
SLOW, and press CH (oo/pp) until
VCR to
VCR, then
uttons on the VCR/DVD
uttons on the remote control
Channel Reprogramming
You can replace two channels.
1
Press
2 3 4 5
6
7
Speed Search
1
2
3
Still Picture
Press STILL/PAUSE during playback to view a still picture on the TV screen.
• When the picture begins to vibrate vertically, stabilise the
• After the VCR/DVD has been in Still mode for 5 minutes, it
NOTE (for “Speed Search” and “Still Picture”):
Slow Motion
• Press SLOW to reduce the playback speed. The VCR/DVD
• If it is left in the Slow mode for more than 5 minutes, the
VCR, then MENU. Press K or L to select INITIAL, then press B. Press K or L to select CH TUNING, then press B. Press K or L repeatedly to select MOVE, then press B. Press
K or L repeatedly to select the position number you want to change the channel, then press B.
•You cannot select a position number where “- - - ” appears next to the number. This is because SKIP is set to [ON] for this position number.
• When a weak signal is received in Channel Reprogramming mode, you can change the back­ground to static blue by pressing CLEAR/C-RESET. If you press the button again, the background will return to the static screen.
K or L repeatedly until the channel move to another
Press position number, then press B. Press the MENU.
During playback, press FWD DDor REV EEto view a videotape at a high speed in either a forward or reverse direction. In this mode, the sound will be muted. Press the button again, the VCR/DVD will now search in super high speed. (This function will not operate for a NTSC tape.)
PLAY to return to normal playback.
Press
picture by pressing the CH (oo/pp) in the Still mode.
will stop automatically to protect the tape and the video head.
• Usually there will be video “noise” lines (black and white streaks or dots) on the screen. This is normal.The still picture will, in addition to containing the “noise” lines, be black and white.This is not a fault of the machine but merely a by-product of the technology involved in producing a VCR with LP mode.
mutes the sound during slow motion. You can control the speed by pressing Press PLAY to return to normal playback.
VCR/DVD will automatically switch to the Stop mode.
FWD DD(faster) or REV EE(slower).
–14–
EN
VCR OPERATION
• During playback of the recorded tape in Hi-Fi mode:
Mode
Stereo
L
R
Normal
STEREO
LEFT
RIGHT
- None -
Display on
the TV screen
Hi Fi L Audio Hi Fi R Audio Hi Fi L Audio Hi Fi L Audio Hi Fi R Audio Hi Fi R Audio
Normal Audio Normal Audio
L R L R L R
L R
AUDIO OUTPUT
• During reception of bilingual broadcasts:
• Reception of stereo broadcasts:
STEREO
LEFT
RIGHT
- None -
Display on
the TV screen
Display on
the TV screen
Mode
MAIN
SUB
MAIN
SUB
MAIN
SUB
MAIN
SUB
Main Audio Main Audio Sub Audio Sub Audio Main Audio Sub Audio
L R L R L R
AUDIO OUTPUT
Mode
Stereo
L
R
Monaural
L Audio R Audio L Audio L Audio R Audio R Audio
L+R Audio L+R Audio
L R L R L R
L R
AUDIO OUTPUT
Recording
Viewing and Recording the Same Programme
1
Insert a cassette tape with its erase-prevention tab in place. (If necessary, rewind or fast forward the tape to the point at which you want to begin recording.)
2
Press the numerical buttons or CH (oo/pp) to select the channel to be recorded.
3
Press TAPE SPEED to select the tape speed (SP/LP).
4
Press REC/OTR to begin recording.
• The REC indicator on the display comes on.
5
Press STOP when recording is completed.
Skipping unwanted Programme Material during Recording
1
Press STILL/PAUSE when you want to temporarily halt
recording.
• You can check the remaining pause time with marks on the TV screen. Each mark represents 1 minute. After 5 minutes, the VCR will automatically switch to the Stop mode to prevent tape damage.
2
Press STILL/PAUSE or REC/OTR to resume recording.
Recording one Programme while viewing another
You can record one programme while viewing another. To start recording, follow steps to under “Viewing and Recording the same Programme”. Then, set the TV to the channel you want to watch.
To monitor the progress of your recording
Select the video channel on the TV.
Assemble Function
You can record in continuation from previous programme on a pre-recorded tape.
1
Insert a pre-recorded tape. Press
2
Press STILL/PAUSE at the desired point on the tape.
3
Press REC/OTR. The VCR/DVD will be the Recording Pause mode.
4
Press CH (oo/pp) to select the channel to be recorded .
5
Press REC/OTR or STILL/PAUSE. The recording will begin.
6
Press STOP when recording is completed.
41
PLAY to start playback.
NOTES:
• If you play non-Hi-Fi tapes, the VCR/DVD will play auto­matically in monaural even if you select any mode.
• If the stereo signal becomes weak, the broadcast is automatically recorded in monaural.
OTR (One Touch Recording)
This function enables you to set the duration of a recording simply by pressing
Follow steps to in “Viewing and Recording the same Programme”.
2
Press
REC/OTR repeatedly until the desired recording
length appears in the upper left corner of the TV screen.
REC/OTR.
311
Hi-Fi Stereo Sound System
This VCR/DVD will record and playback Hi-Fi stereo sound. In addition it has a A2 and NICAM stereo sound decoder. This equipment will receive stereo and bilingual broadcasts and there are several ways of recording and playing back the sound.
Selecting the Sound Mode
You can select each mode by pressing AUDIO. Each mode is indicated on the TV screen as following.
NOTE:
–15–
Recording stops when 0:00 is reached.
To check remaining time during an OTR, press DIS­PLAY.
To change the recording length during an OTR, press REC/OTR repeatedly until the desired length appears.
To stop an OTR before recording is finished, press STOP.
To cancel the OTR but continue recording, press REC/OTR repeatedly until I appears without the
recording length.
If there is no timer recording set after an OTR, the
VCR/DVD switches to DVD mode and TIMER indicator flashes because the VCR is still on standby for timer recordings. Press TIMER ON/OFF on the remote con­trol or STOP/EJECT on the VCR/DVD to cancel timer standby, then press VCR button to use the VCR again. If there is a timer recording set after an OTR, the VCR/DVD switches to the DVD mode and TIMER indi­cator lights up, indicating that the VCR/DVD is on timer standby. Press TIMER ON/OFF on the remote control or STOP/EJECT on the VCR/DVD to cancel timer standby, then press VCR button to use the VCR again.
EN
VCR OPERATION
Auto Repeat Playback
The VCR/DVD has an auto repeat function that allows you to repeat a tape indefinitely without touching PLAY.
1
Insert a pre-recorded tape and press
2
Press K or L to select SET UP, then press B.
3
Press K or L to select AUTO REPEAT.
4
Press B so that ON appears next to AUTO REPEAT on the TV screen. When in Stop mode, Auto Repeat mode will start automatical­ly. If the on-screen menu still remains, press MENU to exit, then press PLAY.
NOTE:
• Once you select the Auto Repeat mode, it stays in effect even after you turn off the VCR/DVD.
To stop playback Press STOP.
To exit the Auto Repeat mode
Repeat steps to .Then, press B. OFF will appear next to AUTO REPEAT on the TV screen. Press MENU to exit.
31
VCR, then MENU.
Picture Select
This function enables you to select the picture quality of a tape.
1
Press
2 3 4
5
NOTE:
VCR, then MENU.
Press K or L to select SET UP, then press B. Press K or L to select PICTURE. Press B until the desired mode (NORMAL, SOFT, or SHARP) is indicated on the TV screen.
Press MENU to exit.
• Once you select the Picture Select mode, it stays in effect even after you turn off the VCR/DVD.
Automatic Operation
Automatic Rewind, Eject, Off
When the end of a tape is reached during recording, play­back or fast-forward, the tape will automatically rewind to the beginning. After that, the VCR/DVD will eject the tape.
• The tape will not auto-rewind during timer recording or One Touch Recording.
Tape Eject
A tape can be ejected with the VCR/DVD power on or off (but the VCR/DVD must be plugged in).
• If a timer recording is set, press STOP/EJECT twice to eject a tape.
Real Time Tape Counter
• This shows the elapsed recording or playback time in hours, minutes and seconds on screen. (Nothing is shown in the case of blank portion)
• The “ – ” indication will appear when the tape is rewound further than the tape counter position “0:00:00”.
• To reset tape counter, press CLEAR/C-RESET.
Timer Recording
You may programme the VCR/DVD to start and end a record­ing while you are away.You can set 8 programmes to record on specific days, daily or weekly within a 1-year period.
• Insert a tape with its erase-prevention tab in place. (If nec­essary, rewind or fast forward the tape to the point at which you want to begin recording.)
1
Press
VCR, then MENU.
Press K or L to select TIMER, then press B.
2
NOTES:
• If you have not set the clock yet, CLOCK setting menu appears. If so, follow the steps outlined in “Setting the Clock”. Then, set the timer.
• When you press
• If you do not press
• Press
3
Programme number flashes. Press until the desired programme number appears. Then, press B.
4
For everyday recording :To record a TV programme at
5
For once-only recording only : Press K or Lrepeatedly
until your desired day appears.
6
Press K or L repeatedly until the relevant start hour appears. Next, enter the minute digit.
7
Press K or L repeatedly until the relevant end hour appears. Next, enter the minute digit.
8
Press K or L repeatedly until the relevant channel num­ber appears.
9
Press K or L repeatedly until your the desired tape speed appears.
10
Press K or L repeatedly to set VPS/PDC ON or OFF.
11
Press B. Programme 1 is now completed.
•To set another timer programme, repeat steps to .
12
Press MENU to exit.
13
Press TIMER ON/OFF to activate the timer. The TIMER indicator on the VCR/DVD comes on.
93
to ,the input mode will move to the next step.
item, the input mode will move to the next step.
s to go back one step from the current setting during steps to . If s is pressed when the TIMER NUMBER is flashing, the entire programme contents will be erased.
For once-only recording : Press K or L repeatedly
until the relevant month appears.
For daily recording :To record a TV programme at the same time on the same channel from Monday through Friday. While the month digit is flashing, press repeatedly to select MO-FR.
the same time on the same channel every day. While the month digit is flashing, press MO-SU.
For weekly recording :To record a TV programme at the same time on the same channel every week. While the month digit is flashing, press select W-MO (Example: every monday).
B after pressing K or L during steps
B within 5 seconds of setting an
4
10
K or L repeatedly
K or L
K or L repeatedly to select
K or L repeatedly to
11
3
–16–
EN
VCR OPERATION
To stop a Timer Programme which has already started
Press STOP/EJECT on the VCR/DVD.
NOTE: STOP on the remote control will not function in the
“Timer Recording” mode.
To correct timer programmes
If you want to correct an automatic timer after you finished setting programme,
1
Repeat steps to in the “Timer Recording” section.
2
Select the setting you want to change using
3
Enter the correct numbers using K or L, then press B.
4
Press MENU to exit.
5
Press TIMER ON/OFF to return to timer stand-by mode.
To cancel or check the start/end time
1
Repeat steps to in the “Timer Recording”.
2
Select a programme number you want to check using K or L. The details of selected programme appears on the TV screen. You may cancel the entire programme by pressing s.
3
Press MENU button to exit.
To avoid overlap of TIMER programmes ...
A timer programme will not work while another programme is under execution.
Programme 1
Programme 2
Programme 3
Hints for Timer Recording
• If there is a power failure or the VCR/DVD is unplugged for more than 1 hour, clock and all timer settings will be lost.
• If a tape runs out before a timer recording is finished, the unit ejects the tape and switches into DVD mode automati­cally. Press TIMER ON/OFF to active VCR function.
• Once the unit goes into Timer-standby mode, no VCR func­tions are available until TIMER ON/OFF is pressed. (OUT PUT on the front panel and VCR on the remote control will not function.)
• Press TIMER ON/OFF to activate VCR functions after your timer recording is finished.
• DVD functions are available during Timer-standby mode and Timer recording. You don’t have to stop your timer recording.
• If the DVD does not be used after you set the VCR/DVD in Timer-standby mode by pressing TIMER ON/OFF, press
OPERATE to turn off the VCR/DVD.
31
s or B.
21
9:00 10:00 11:00
SHOWVIEW®Guide Channel Set
Setting the guide channels for the SHOWVIEW system
First, fill in the boxes below: Write your local channel numbers in “VCR Channel” columns, corresponding “TV-Station” and “GUIDE Channel” columns, using your TV guide magazine or the TV listings of your local newspaper.
GUIDE
Channel
Now, compare the channel numbers you have written in the GUIDE Channel and VCR Channel columns.You must set all of these channel numbers that do not match using the follow­ing procedure before you programme the automatic timer recording using the SHOWVIEW system.
• This setting only needs to be set once, but must be done again if you use this VCR/DVD in another area by moving it.
1
Press MENU.
2
Press K or L to select INITIAL, then press B.
3
Press K or L to select GUIDE CHANNEL, then press B.
4
Press K or L to select the relevant mode, then press B.
•To set the guide channel individually, select MANUAL. Then press B and continue with step .
•To set all of the guide channels to AV1, AV2 or AV3 select “AV1”, “AV2” or “AV3”. Then press MENU to exit.
5
Press K or L repeatedly to select the position number, then press B.
6
Press the numerical buttons, K or L to enter guide channel number, then press B.
• Press s to erase all digit.
•You can select guide channels 1-255.
•To select channels from 1 to 9, first press “0” twice then 1 to 9.
•To select channels from 10 to 99, first press “0” once then press the last two digits. (To select channel 80, first press “0” then press “8” and “0”).
7
Press MENU to exit.
TV-Station
VCR
Channel
5
Timer Recording Using the S
You can programme the timer using the SHOWVIEW programme numbers that are printed in TV guide magazine.You can set 8 programmes to record.
• Insert a cassette tape with its erase prevention tab in place. (If necessary, rewind or fast forward the tape to the point at which you want to begin recording.)
1
Press the
NOTE: If you have not set the clock yet, the CLOCK setting
2
Press the numerical buttons to set the SHOWVIEW num- ber of the programme you want to record.
• Press s to go back one digit from current digit while
3
FOR ONCE-ONLY RECORDING : Press the SHOWVIEW button.
SHOWVIEW buttons.
menu will appear. If so , follow the steps outlined in the “Setting the Clock”. Then, set the timer.
you set the SHOWVIEW number.
HOWVIEW
System
–17–
EN
VCR OPERATION
FOR DAILY RECORDING :To record a TV programme at the same time on the same channel, from Monday to Friday. Press DAILY/WEEKLY repeatedly to select DAILY (MO- FR), then press the SHOWVIEW button.
FOR EVERYDAY RECORDING :To record a TV pro- gramme at the same time on the same channel every day. Press DAILY/WEEKLY repeatedly to select DAILY (MO- SU), then press the SHOWVIEW button.
FOR WEEKLY RECORDING :To record a TV pro- gramme at the same time on the same channel every week. Press DAILY/WEEKLY repeatedly to select WEEKLY, then press the SHOWVIEW button.
NOTES:
• If the SHOWVIEW number is not available, it will be cleared automatically when you press the SHOWVIEW button. Enter the correct SHOWVIEW number and press the SHOWVIEW button again.
• If the SHOWVIEW number flashes when you press the SHOWVIEW button, this means that the SHOWVIEW num- ber you entered was incorrect or the timer recording you just programmed and another timer recording overlap.
4
Confirm the channel number, then press
• If your local channel information is programmed in VCR/DVD’s memory, your local channel number appears automatically.
• If your local channel information is not programmed in VCR/DVD’s memory, “– –” or an incorrect channel number may appear. In this case, press K or L repeatedly until your desired channel number appears. Then, press B.
• When you select the channel number using K or L, it memorises in VCR/DVD’s memory.
5
Press K or L repeatedly until the desired tape speed appears.
6
Press K or L to set VPS/PDC ON or OFF.
7
Press MENU to exit.
8
Press TIMER ON/OFF to activate the timer. The TIMER indicator on the VCR/DVD comes on.
B.
Auto Return
If there are any remaining programmes including Daily, Everyday and Weekly, AUTO RETURN will not operate.
1
Press VCR, then MENU.
2
Press K or L repeatedly to point to SET UP, then press B.
3
Press
K or L to point to AUTO RETURN, then press B.
ON will appear next to AUTO RETURN.
4
Press MENU.
Watch the Recorded TIMER PROGRAMME Press OPERATE to turn on the VCR/DVD, then press PLAY.
VPS (Video Programme System) /
PDC (Programme Delivery Control)
The Video Programme System (VPS) or the Programme Delivery Control (PDC) is a very convenient system which assures that the TV programmes you have programmed for timer recording, will be recorded exactly from beginning to end, even if the actual broadcasting time differs from the scheduled time due to delayed start or extension of the programme dura­tion. Also, if a programme is interrupted and, for example, some special news is broadcast, the recording will also be interrupted automatically and resumed when the programme continues.
When the VPS/PDC signal drop out because the broadcast sig­nal is weak, or when a broadcasting station does not transmit a regular VPS/PDC signal, the timer recording will be performed
in the normal mode (without VPS/PDC) even if it was pro­grammed for VPS/PDC. When the starting time of the VPS/PDC timer recording is from 0:00 to 3:59 on a given day, the VPS/PDC function operates from 20:00 on the previous day to 4:00 on the following day. When the starting time of the VPS/PDC timer recording is from 4:00 to 23:59 on the given day, the VPS/PDC function operates from 0:00 on the day to 4:00 on the following day. This means that if the relevant pro­gramme is broadcasted within this period, it will be recorded correctly. If the timer is not programmed correctly, the incorrect timer setting stays in effect unless you cancel it. To cancel the incorrect timer setting, refer to “To Cancel or Check the Start/End Time” on page 17.
Quick-Find
This function enables you to search and confirm the contents of the recorded programme(s) using the index mark.
• The tape must be fully rewound.
1
Press VCR, then QUICK-FIND.
To skip to the beginning of next programme Press QUICK-FIND.
To view at normal speed Press PLAY.The Quick-Find is cancelled.
NOTES:
• This function will not operate in the Recording mode.
• When you want to cancel the Quick-Find while in progress, press STOP.
• When the end of a tape is reached during the Quick­Find, the tape will automatically rewind to the begin­ning. After rewinding finishes, the VCR/DVD will eject the tape.
Index Search
• The index mark will be made automatically when REC/OTR is pressed. It will also be marked at the starting point of Timer recording and OTR.
• The index mark is not recorded if STILL/PAUSE is pressed and released during recording.
• The time gap between index marks on the tape should be greater than 1 minute for SP recording and 2 minutes for LP recording.
1
Press
2
3
NOTES:
VCR, then SEARCH MODE.
Press K or L repeatedly until the number of pro­grammes that you want to skip appears. Press s or B. The VCR/DVD begins rewinding or fast forwarding to the beginning of desired programme.
• When the preset programme is reached, the VCR/DVD will start playback automatically.
• Index Search can be set up to 20.
• This function will not operate in the Recording mode.
• Operations must be followed up within 30 seconds, from steps to . Otherwise the Index Search mode will be cancelled.
• To exit the Index Search mode, press MENU in step
.Or press STOP after step .
32
32
–18–
EN
VCR OPERATION
DVD
DIGITAL
AUDIO OUT
ANALOG
AUDIO OUT
S-VIDEO
OUT
L
R
VCR AV2 (DECODER)
AV1 (TV)
DVD/VCR
AERIAL
RF OUT
to RF OUT
to aerial jack
[Source (Playing) VCR <Monaural>]
(another VCR)
to 21-Pin scart terminal
[TV set]
(Use for monitoring)
[Editing (Recording) VCR/DVD]
(this unit)
Round coaxial cable (supplied)
SP
0:12:34
SP
17:40
P02
<CLOCK and CHANNEL
NUMBER mode>
<COUNTER mode>
Press once. Press once.
Press once.
<OFF mode>
Time Search
If a tape includes both programmes recorded in the PAL sys­tem and ones recorded in the NTSC system, this function may not be operated correctly.
1
Press
2 3
VCR, then SEARCH MODE twice.
Press K or L repeatedly until the desired time appears. Press s or B. The VCR/DVD begins rewinding or fast forwarding to the
specified point. When 0:00 is reached, the VCR/DVD will start playback auto­matically.
NOTES:
• Time Search can be set up to 9 hours 59 minutes (9:59).
• This function will not operate in the Recording mode.
• Operations must be followed up within 30 seconds, from steps to . Otherwise the Time Search mode will be cancelled.
To exit the Time Search mode, press MENU in step .
Or press STOP after step .
32
2
3
Recording from DVD to VCR
1
To activate DVD function, press DVD.
2
Insert a non-copyright-protection DVD, then press PAUSE at the point where you want to start recording.
3
Press VCR, then insert a tape with its erase-prevention tab in place. Make sure the VCR function is in Stop mode after you find your recording point.
4
TAPE SPEED to choose your recording speed.
Press SP or LP appears on the front panel display.
5
Press 0, 0, 4, with the numerical buttons, then “disc” briefly appears on the front panel display.
6
Press REC/OTR.
•The recording of the DVD’s paused image selected at
2
step starts.
7
Press DVD, then press PLAY.
•The recording of the DVD’s moving image starts.
8
To stop recording, press VCR, then STOP.
Copying a Video Tape
You can make copies of videotapes made by friends or rela­tives for your own enjoyment.
WARNING: Unauthorised recordings of copyrighted video tapes may be an infringement of copyright laws.
Connect the recording VCR/DVD (this unit), playing VCR (another VCR) and your TV as outline in the following dia­gram.
3
Press TAPE SPEED to select the desired recording speed (SP/LP).
4
Select “AV2” position on the recording VCR/DVD.
5
Press REC/OTR on the recording VCR/DVD.
6
Begin playback of the tape in the playback VCR.
7
To stop recording, press STOP/EJECT on the recording
VCR/DVD, then stop playback of the tape in the playing VCR.
NOTES:
• For best results during dubbing, use the VCR/DVD’s front panel controls whenever possible. The remote control might affect the playback VCR’s operation.
• If video or colour fades in and out, you may be copying a copy guarded video tape.
• Unauthorised recording of copyrighted materials may infringe on the rights of copyright owners, violate copy­right laws and may not record clearly.
To monitor the recording
Tu rn on the TV and select the video channel on the TV.
Status Display
• To check the Counter, or Clock & Channel number,
press DISPLAY. Each time you press DISPLAY, TV screen will change as illustrated: When you select the channel using the numerical
buttons, select the desired channel (position number).
NOTE: If the display shows an abnormal reading or no read-
ing, press RESET button on the bottom of the VCR/DVD.
Video Cassette Tape
This VCR/DVD will operate with any cassette that bears the VHS mark. For best results, we recommend the use of high­quality tapes. Do not use poor quality or damaged tapes.
• You can prevent accidental erasing of a recording by breaking off the erase­prevention tab on the back edge of the cassette.
• If you decide to record on the tape again, cover the hole with plastic tape.
Two Different Tape Speeds
Before recording, select the tape speed : SP mode (Standard Play) or LP mode (Long Play).
The table below shows the maximum recording/playback time using E-60, E-120, E-180 or E-240 tapes in each mode.
Ta b
1 2
Insert a pre-recorded tape into the playing VCR. Insert a tape with its erase prevention tab in place into the cassette compartment of the recording VCR/DVD.
–19–
TYPE OF TAPE RECORDING/PLAYBACK TIME
TAPE SPEED E-60 1 HOUR 2 HOURS E-120 2 HOURS 4 HOURS E-180 3 HOURS 6 HOURS E-240 4 HOURS 8 HOURS
SP MODE LP MODE
EN
VCR OPERATION
TV Colour System
Different countries use different television colour systems. Tapes recorded in the PAL or NTSC system can be played back on this unit. Usually, the picture on the TV screen will be in black and white when you play back a tape that is recorded in a different colour system.
Tapes recorded in the NTSC system can be played back on
PLAYING A DISC
this unit and a PAL system TV set. This feature is only avail­able in the SP mode. When playing back such tapes, the pic­ture may roll up or down, shrink vertically and black bars may appear both at the top and bottom of the screen. Adjust the vertical hold control on your TV, if the TV features this con­trol.
Basic Playback
VR mode
VCDDVD-RWMP3CDDVD
JPEG
Getting started
•Turn on the power of the TV, amplifier and any other com­ponents which are connected to the VCR/DVD.
• Make sure the TV and audio receiver (commercially avail­able) are set to the correct channel.
• When you play NTSC recorded discs, the default setting converts this to a modified PAL (Refer to page 28 “Display Settings”).
1
2
3
4
5
NOTES:
OPERATE, then DVD.
Press
Press
OPEN/CLOSE to open disc
loading tray.
Place the chosen disc on the tray, with the label facing up.
Press
PLAY.
• The tray will close automatically, and playback will then start from the first chapter or track of the disc. If the playback does not start automatically, press
• When you playback the DVD which a title menu is recorded, it may appear on the screen. In this case, refer to “TITLE MENU”.
STOP to stop playback.
Press
•A “prohibited icon” may appear at the top-right on the TV screen during operation, warning that a prohibited operation has been encoun­tered by the VCR/DVD or the disc.
•With DVDs that use some titles for playback pro­gramme signals, playback may start from the second title, or it may skip these titles.
• During the playback of two layered disc, pictures may stop for a moment. This happens when the 1st layer switches to the 2nd layer. This is not a malfunction.
•A DVD-RW disc recorded in the VR mode may freeze momentarily during playback depending on how the playlist was made and edited (deleted titles, repeated recording).
PLAY.
General Features
DVDs or Video CDs may contain menus to navigate the disc and access special features. Enter an appropriate number or
Arrow ( K /L / s / B ) to highlight your selection in the
use DVD main menu and press
NOTE:
• Unless stated, all operations described are based on remote control use.
Cancelling PBC* (for playback of a Video CD)
1
Insert a Video CD. (Playback will start automatically.)
2
Press
STOP.
3
Enter track number of your choice with the
buttons.
4
PBC is now cancelled and the playback of the Video CD will start.
*
What is PBC?
“PBC” stands for the PlayBack Control. You can play interac­tive software using a menu screens. Refer to instructions of Video CD.
ENTER to confirm.
numerical
Pause
VR mode
1
During playback, press STILL/PAUSE.
• Playback will pause and sound will be muted.
2
To continue playback, press
NOTE:
• Set STILL MODE to FIELD on the Display menu if pic­tures in the pause mode are blurred. (Refer to page 28.)
PLAY.
VCDDVD-RWMP3CDDVD
Disc Menus
DVD
1
Press MENU.
• The DVD main menu will appear.
2
If the feature is not available, symbol may appear on the TV screen.
3
If disc menu is available on the disc, audio language, subtitle options, chapters for the title and other options will appear for selection.
4
Press
Arrow ( K /L / s / B ) to select an item, and
ENTER to confirm selection.
–20–
EN
PLAYING A DISC
ORIGINAL PLAYLIST
1 PLAYLIST1 2 PLAYLIST2 3 PLAYLIST3 4 PLAYLIST4 5 PLAYLIST5
Title Menu
DVD
1
Press TITLE.
• The title menu will appear.
2
If the feature is not available, symbol may appear on the TV screen.
3
Press Arrow ( K /L / s / B ) to select an item, and ENTER to confirm selection.
• Playback will begin at the selected Title.
To call up a menu screen during playback
• Press MENU to call up the DVD main menu.
• Press TITLE to call up the title menu.
VCD
1
Insert a Video CD.
• The title menu will appear.
2
Press the numerical buttons to select the menu. Playback will start.
NOTE:
• Contents of menus and corresponding menu opera­tions may vary between discs. Refer to the manual accompanying the disc for details.
Step by Step Playback
1
During playback, press STILL/PAUSE.
VR mode
• Playback will pause and sound will be muted.
2
The disc goes forward by one frame each time
STILL/PAUSE is pressed.
3
To exit step by step playback, press PLAY.
NOTE:
• Set STILL MODE to FIELD on the Display menu if pic­tures during step by step playback are blurred. (Refer to page 28.)
VCDDVD-RWDVD
Rapid Play
DVD
Available only on discs recorded in the Dolby Digital format, Rapid Play plays back in slightly faster/ slower speed while keeping the sound quality as in the normal playback.
1
Press
MODE during playback.
• The current setting appears.
2
s or B to switch among
Press
(x1.3), (x0.8) and OFF.
: Plays back approximately at 0.8 times of normal
playback.
: Plays back approximately at 1.3 times of normal
playback.
3
To return to normal playback, press PLAY.
NOTES:
•Audio (language) setting cannot be changed while using this mode.
• Vir tual Surround and Digital Gamma settings cannot be changed while using this mode.
• Vir tual Surround does not function while using this mode.
• This feature may not work at some point in a disc.
• When using digital audio connection (COAXIAL), the PCM sound will be output.
OFF
Resume
1
During playback, press STOP.
• Resume message will appear on the TV screen.
2
Press
PLAY, playback will resume from the point at
which playback was stopped.
•To cancel resume, press STOP again.
•To stop playback, press mode.
NOTE:
•For MP3 and JPEG, playback will resume from the beginning of the current track.
without PBC function
STOP twice from playback
Playing the disc recorded in VR mode (Video Recording format)
DVDs recorded in VR mode can have a PLAYLIST assigned to alter the order or content to be played. If a PLAYLIST has been created, you can choose the ORIGINAL or PLAYLIST option.
1
Press
MENU in stop mode.
• The current setting screen will appear.
• Pressing
2
Press
MENU during playback is not valid.
s or B to select ORIGINAL or PLAYLIST.
• PLAYLIST will not be displayed when it has not been made.
• Resume playback will not be possible if you change the setting.
3
K or L to select a title, then press ENTER.
Press
• Playback will start.
NOTE:
• [ORIGINAL]: A list of titles which are recorded with a DVD recorder. [PLAYLIST]: A list of titles which is made based on the ORIGINAL edited list.
–21–
DVD-RWVCDCDDVD
VR mode
DVD-RW
VR mode
EN
PLAYING A DISC
Fast Forward / Reverse Search
1
During playback, press FWDg or REVh repeatedly to select the required forward or reverse speed.
•For DVDs, fast forward or reverse search speed is dif­ferent depending on the disc. Approximate speed is 1 (x2), 2(x8), 3 (x50), and 4 (x100).
•For Video CDs, fast forward or reverse search speed is different depending on the disc. Approximate speed is 1(x2), 2(x8), 3(x30).
•For audio CDs, the approximate speed is x16.
•For MP3, the approximate speed is x8.
• If you are using press and hold it for more than 1.5 seconds. When you reach the desired speed, release the button.
2
To return to normal playback, press
FFg or REWh on the front panel,
VR mode
PLAY.
VCDDVD-RWMP3CDDVD
Slow Forward / Reverse
1
During playback, press STILL/PAUSE.
2
Press
FWDg or REVh.
• Slow motion playback will begin and sound will be muted.
3
Press
FWDg or REVh repeatedly to select the
required speed.
• Slow forward or reverse speed is different depending on the disc. Approximate speed is 1 (1/16), 2 (1/8), and 3 (1/2).
• If you are using panel, press and hold it for more than 1.5 seconds. When you reach the desired speed, release the button.
4
To return to normal playback, press
NOTES:
• Set STILL MODE to FIELD on the Display menu if pic­tures in the slow playback mode are blurred. (Refer to page 28.)
• You cannot play Video CDs in reverse slow motion.
FF g or REW h on the front
VR mode
PLAY.
VCDDVD-RWDVD
Zoom
The Zoom function allows you to enlarge the video image and to pan through the enlarged image.
1
2
3
4
NOTES:
ZOOM during playback.
Press
• Playback will continue.
Press
ZOOM repeatedly to select the required zoom fac-
tor: x2, x4 or OFF.
Use
Arrow ( K /L / s / B ) to move the zoomed picture
across the screen.
To exit zoom mode, press
• Zooming function does not work while disc menu is shown.
• x4 zoom is not available on some discs.
• Only x2 zoom is available on Video CDs and JPEG.
•You may not be able to move zoomed JPEG pictures.
VR mode
ZOOM to OFF.
JPEGVCDDVD-RWDVD
Track Search
There are three ways to begin playback on an Audio CD, Video CD, MP3 or JPEG disc at a specific Track.
Using the Numerical buttons
1
Press the numerical buttons to enter the desired Track number.
• Playback will start at the selected track.
•For single digit tracks (1-9), press a single number (eg. track 3, press 3).
To play track 26, press +10, 2, 6 on the numerical but-
tons.
Using the DIRECT SKIP.
1
Press DIRECT SKIP.
• The track search display appears.
2
Within 30 seconds, select a desired track number using the
numerical buttons.For single digits press “0” first.
• Playback will start at the selected track.
Using the SKIP HG
During playback, press Press it quickly and repeatedly to skip subsequent tracks. Press track. Press it repeatedly to go to the previous tracks.
•Track number will appear briefly on the VCR/DVD dis-
• If SKIP is pressed while the playback is paused, the
NOTE:
SKIP HGare not available when playback is
H to go back to the beginning of the current
SKIP
play panel.
playback will be paused again after skipping to the next track.
stopped.
G to move to the next track.
SKIP
without PBC function
JPEGVCDMP3CD
Title / Chapter Search
DVD-RWDVD
1
During playback, press DIRECT SKIP repeatedly until the
Chapter Search or the Title Search screen appears.
2
Enter the desired chapter/title number using the
cal buttons.
NOTE:
• Depending on the disc being played, this function can also be performed by directly entering the desired chapter number using manual accompanying the disc.
numerical buttons. Refer to the
VR mode
/2
numeri-
–22–
EN
PLAYING A DISC
Time Search
VCDDVD-RWCDDVD
1
During playback, press DIRECT SKIP repeatedly until the
Time Search screen appears.
2
Within 30 seconds, enter a desired disc time using the
numerical buttons.
• Playback will start at the specified time.
• When there is no need to enter a number, “0” appears automatically. For example, “0:0_:_ _” appears in the Time Search display if the total time of the disc is less than 10 minutes.
NOTE:
• Press CLEAR/C-RESET to erase the incorrect input.
VR mode
without PBC function
Repeat
REPEAT are available only during playback.
DVD
To activate the repeat function, press REPEAT during playback.
• The repeat mode changes as described below every time you press the button.
CHAPTER TITLE OFF
(current chapter repeat) (
CHAPTER
(current chapter repeat) (current title repeat) (repeat off)
NOTES:
• Repeat Title/Chapter is not available with some scenes.
• The REPEAT setting will be cleared when moving to other title or chapter.
To activate the repeat function, press REPEAT during playback.
• The repeat mode changes as described below every time you press the button.
TRACK
(current track repeat) (entire disc repeat)
NOTES:
• The REPEAT setting will be cleared when moving to other track.
• Repeat playback does not function during A-B REPEAT playback.
current title repeat) (repeat off)
DVD-RW
VR mode
TITLE
ALL
ALL
(entire disc repeat)
OFF
VCDCD
without PBC function
OFF
off)
(repeat
JPEGMP3
A-B REPEAT
1
Press A-B REPEAT at your chosen starting point.
A- appears briefly on the TV screen.
2
Press A-B REPEAT again at your chosen end point.
A-B appears briefly on the TV screen, and the repeat sequence begins.
3
To exit the sequence, press A-B REPEAT.
NOTES:
• The A-B REPEAT section can only be set within the current title (for DVDs), or current track (for audio CDs).
• A-B REPEAT is not available with some scenes in DVD.
• To cancel the A point which was set, press CLEAR/C- RESET.
• A-B REPEAT playback does not function during title, chapter, track or all repeat playback.
VR mode
Programme (CD)
You may determine the order in which tracks will play.
1
Press
MODE (playback
must first be stopped).
• The PROGRAM screen will appear.
2
Press
or to select a
track, then press
3
Press
NOTES:
CLEAR/C-RESET
• Press to erase the most recently entered programme.
PLAY to play the programmed tracks.
• While the programme is being played back, the STOP works as follows.
• Press STOP once and then PLAY again, playback will restart from the point where STOP was pressed. (Programme continued)
STOP twice and then PLAY. Playback starts
• Press from the track in the original order. However, the pro­gramme can be called back when you follow the above steps. Your programmes will be stored unless either the disc tray is opened or power is turned off.
• Up to 99 programmes can be entered.
• To erase all tracks in the programme at once, select ALL CLEAR at the bottom of the list at step .
• To repeat the current track in the programme, press REPEAT repeatedly until TRACK appears during playback. If you like to repeat the entire programme
REPEAT repeatedly until ALL appears during
press playback.
• Refer to page 25 for programme playback of MP3 and JPEG.
ENTER.
0:03:30
2
VCDDVD-RWCDDVD
CD
TRACK
(current track repeat) (current group repeat) (repeat off)
GROUP
ALL
(entire disc repeat)
OFF
–23–
EN
PLAYING A DISC
Picture 1 Picture 2 Picture 3
Picture 4
Current track number /
the number of total tracks
Picture 5 Picture 6
1/32
Random Playback (CD)
This shuffles the playing order of tracks instead of playback in the sequence.
1
In stop mode, press
MODE
repeatedly until the RAN­DOM screen appears.
2
Press
PLAY to start random
playback.
NOTES:
• To repeat the current track in the random selection, press
REPEAT repeatedly until TRACK appears
during playback. To repeat the entire random selection press
REPEAT repeatedly until ALL appears during
playback.
• Refer to page 25 for random playback of MP3 and JPEG.
MP3/JPEG Playback
When a CD with MP3 or JPEG files is inserted in the VCR/DVD and MENU is pressed, the FILE LIST will appear on display. The number of tracks is also displayed on the front panel.
1
Press
K or L to select the desired group (folder) or track.
• If a group (folder) is
selected, press B or ENTER to go on to the track selection screen. Press K or L to choose a track, then press PLAY or ENTER.
• If a track is selected,
press PLAY or ENTER to start playing tracks. Starting from the one that has been chosen and the subsequent tracks will be played.
• Press TITLE to return to the first item.
2
Press STOP to stop playback.
NOTES:
• Folders are known as Groups; files are known as Tracks.
• Folders are accompanied by icon.
• MP3 files are accompanied by icon.
• JPEG files are accompanied by icon.
• Maximum of 255 folders can be recognised.
• Maximum of 512 files can be recognised.
• Up to 8 hierarchies can be created.
This VCR/DVD recommends the use of files recorded at the below specifications:
• Sampling frequency: 44.1kHz or 48kHz
• Constant bit rate: 112kbps ~ 320kbps.
Applicable JPEG file Remarks
Size of image
Upper limit: 6300x5100 dots Lower limit: 32x32 dots
A JPEG image that extends beyond the screen is reduced so that it will be displayed within the screen.
JPEG
folder name 1 folder name 2 folder name 3 folder name 4 file name 1 file name 2 file name 3
folder name 1
JPEGMP3
CD
Information on MP3 and JPEG files
• This VCR/DVD can play back images and sounds from data recorded in MP3 and JPEG formats on CD-R and CD-RW discs.
A file with an extension of “.mp3 (MP3)” is called an “MP3 file”.
A file with an extension of “.jpg (JPG)” or “.jpeg (JPEG)” is called a “JPEG file”. The VCR/DVD can run an image file conforming to the Exif specification. Exif is a file format, Exchangeable Image File format established by Japanese Electronic Industry Development Association (JEIDA).
Files whose extension is other than “.mp3 (MP3)”, “.jpg (JPG)” and “.jpeg (JPEG)” will not be listed in the MP3 or JPEG menu.
If the file is not recorded in MP3 or JPEG format, noise may be produced even if the file extension is either “.mp3 (MP3)”, “.jpg (JPG)” or “.jpeg (JPEG)”.
The name of group and track can be displayed in up to 25 characters. Unrecognisable characters will be replaced with asterisks. The ninth and deeper hierarchies cannot be displayed.
Unplayable groups or tracks may be displayed depending on the recording conditions.
If TITLE is pressed when a file list is displayed, the first item will be highlighted.
Kodak Picture CD
The VCR/DVD can also run JPEG files stored on Kodak Picture CDs. The Picture CD is a service to convert pho­tographs taken by a conventional film camera into digital data and write the data on a CD. The user can enjoy picture images on the television set by playing back the Picture CDs.
For details of Kodak Picture CD, contact a shop that deals with developing service of Kodak Inc.
1
Press MENU.Kodak Picture CD menu appears.
If all menu items cannot be displayed in the screen scope, “G ” appears at the right bottom of the screen, indicating that the user can view remaining items on the next page. “H” appears, it indicates that the user can view other items on the pre­vious page. The track number of the currently highlight­ed item and the total tracks are shown at the centre bottom of the screen.
If “G” is shown at the right bottom, use SKIP G to view the next page. If “H” is shown at the left bottom, use SKIP H to view the previous page.
It may take some time until all menu items are dis­played on the menu screen.
2
Press
Arrow ( K /L / s / B ), select a desired track to be
played, then press PLAY or ENTER.
If a Kodak Picture CD file is selected, an image will be played back from the selected track and go to the next one in turn.
3
Press
STOP to stop playback.
NOTES on JPEG and Kodak Picture CD playback
•A track is displayed for 5 seconds and then the next track is displayed.
–24–
EN
PLAYING A DISC
Display on
the TV screen
Mode
MAIN
SUB
MAIN
SUB
MAIN
SUB
MAIN+
SUB
Main Audio Main Audio Sub Audio Sub Audio Main Audio Sub Audio
L R L R L R
AUDIO OUTPUT
•Every press on B will turn the image clockwise by 90 degrees when an image is displayed. A press on s will turn the image counterclockwise by 90 degrees.
• If a group is selected, press K or L to select a desired group, then press B, PLAY or ENTER to select a track.
Slide Show Mode
JPEG
You can switch to the slide show mode during playback.
1
2
3
MODE during playback.
Press
• The slide show mode screen will appear.
• The slide show mode cannot be switched when it is stopped, or from the file list screen or the Picture CD menu screen.
ENTER.
Press
• The slide show mode will change. CUT IN/OUT: The entire image appears in one time. FADE IN/OUT: The image appears gradually and then
MODE to exit.
Press
disappears.
Programme (MP3/JPEG)
JPEGMP3
This feature allows you to programme an MP3 or JPEG disc to play in a desired sequence.
1
Press
MODE (playback must first be stopped).
• The PROGRAM screen will appear.
2
3
NOTES:
K or L to select a track, then press ENTER, to
Press save it in a programme.
CLEAR/C-RESET to erase the incorrect input.
• Press
Press PLAY to start programmed playback.
•To erase all tracks in the programme at once, select ALL CLEAR at the bottom of the list at step .
STOP once and then PLAY again, playback will
• Press restart from the beginning of the track at which was pressed.
• Press STOP twice and then PLAY. Playback starts from the track in the original order. However, the pro­gramme can be called back when you follow the above steps. Your programmes will be stored unless either the disc tray is opened or power is turned off.
2
STOP
Random Playback (MP3/JPEG)
JPEGMP3
1
In stop mode, press MODE repeatedly until the RAN­DOM screen appears.
2
PLAY to play the tracks in random order.
Press
Stereo Sound Mode
VCDCD
1
Press AUDIO repeatedly during playback to select between STEREO, L-CH or R-CH.
STEREO - both right and left channels are active (stereo) L-CH - only left channel is active R-CH - only right channel is active
NOTES:
• If the Virtual Surround setting is ON, the sound mode will be fixed to STEREO, and cannot be changed.
• Stereo sound mode will not be changed when playing DTS CD.
Audio Language
DVD-RWDVD
The VCR/DVD allows you to select a language during DVD disc (if multi language available) playback.
1
Press
2
NOTES:
NOTES (for VR mode only):
AUDIO during playback.
Press AUDIO repeatedly to select your desired language.
• The sound mode cannot be changed during playback of discs not recorded in double sound.
•Audio language selection cannot be made during Rapid
Play. (Refer to page 21.)
• Pressing AUDIO may not work on some DVDs with mul­tiple audio languages (e.g. DVDs which allow audio lan­guage setting on the disc menu).
• Pressing AUDIO cycles the sound mode through MAIN, SUB, MAIN + SUB.
•DVD-RW discs recorded in double sound (two lan-
guages ) can be played back in either sound mode of MAIN, SUB or MAIN + SUB.
• With discs recorded in VR mode, changing the audio
(MAIN, SUB or MAIN+SUB) is effective only when using an analogue connection. Although you may be able to change the settings of the on-screen display, it will not affect the sound when using a digital connec­tion.
VR mode
–25–
EN
PLAYING A DISC
Subtitle Language
DVD-RWDVD
The VCR/DVD allows you to select a language for subtitle during DVD disc (if available) playback.
1
Press
2
3
NOTES:
SUBTITLE during playback.
Press SUBTITLE repeatedly to select your desired subti­tle language.
• The selected language will be displayed on the display bar at the top of the screen.
To turn off subtitles, press SUBTITLE repeatedly until OFF appears.
• Some discs allow audio language setting/subtitle lan­guage setting on the disc menu. (Operation varies between discs, so refer to the manual accompanying the disc.)
• If the desired language is not shown after pressing SUB- TITLE several times, the disc does not have subtitles in that language.
• If you choose a Language that has a 3 letter language code, the code will be displayed every time you change the Subtitle language setting. If you choose any other languages, ‘---’ will be displayed instead. (Refer to page
29.)
• Pressing SUBTITLE may not work on some DVDs with multiple subtitle languages (e.g. DVDs which allow sub­title language setting on the disc menu).
VR mode
Camera Angle
DVD
Some DVDs contain scenes which have been shot simulta­neously from various angles. You can change the camera angle when the ( ) icon appears on the screen. If the ANGLE ICON setting is OFF in the Display setting, the ( ) icon will not appear. (Refer to page 28.)
1
2
ANGLE during playback.
Press
• The selected angle will be displayed on the display bar at the top of the screen.
ANGLE repeatedly to select your desired angle.
Press
Changing the On-Screen Display
DVD-RWDVD
You can check information about the current disc by pressing
DISPLAY on the remote control.
1
2
3
4
1
2
3
DISPLAY during playback to show current Chapter.
Press
• The elapsed and remaining playing time of the current chapter will be displayed.
DISPLAY again to show current Title.
Press
• The elapsed and remaining playing time of the current title will be displayed.
DISPLAY again.
Press
• The BIT RATE and the cur­rent repeat setting will be dis­played.
• If you are playing a dual layered disc, the layer number will also be displayed (L0: Layer 0 is playing. L1: Layer 1 is playing).
If you are playing a DVD-RW with setting the PLAYLIST, the following will also be displayed. ORG: Playing the ORIGINAL. PL: Playing the PLAYLIST.
DISPLAY the fourth time to remove the display.
Press
Press
DISPLAY during playback, the current Track will be
displayed on the TV screen.
• The elapsed and remaining playing time of the current track will be displayed.
DISPLAY again to show current Total Track.
Press
• The elapsed and remaining playing time of the current total track will be displayed.
DISPLAY again to remove the display.
Press
IIII
MP3
1
Press DISPLAY during playback of an MP3 or JPEG disc.
• The name of the file currently in play will be displayed.
2
Press DISPLAY again to show the track number, the elapsed time (for MP3 only), the repeat status, and the playback status at the top of the screen.
will be displayed when the repeat play has been selected.
T- indicates Track repeat G- indicates Group (folder) repeat
3
A- indicates All (disc) repeat
Press DISPLAY again to exit.
VR mode
9/49 0:00:00 -0:00:00
without PBC function
ORGT
VCDCD
JPEG
–26–
EN
PLAYING A DISC
Marker Setup Screen
VCDDVD-RWCDDVD
Use markers to memorise your favourite places on a disc.
1
Press
MARKER during playback.
VR mode
without PBC function
• The display screen and Markers will appear on the TV screen.
2
Press s or B to select a Marker (1 ~ 10), and ensure that “- : - - : - -” appears in the display.
3
When it reaches the desired point, press ENTER.
• Selected number will turn to and the point will be marked.
• The Title or Track and elapsed playing time will appear in the TV screen.
4
To return to the Marker later, press MARKER during playback and s or B to choose the desired marker (one of the mark), then press ENTER.
NOTES:
• Opening the disc tray or turning off the power or select AC (All Clear) at step and press ENTER will erase all
2
Markers.
•To clear a marker, using s or B, position the cursor on to the marker number to be cleared and press CLEAR/C- RESET.
•You can mark up to 10 points.
5
Press MARKER or RETURN to exit.
Digital Gamma Setting
DIGITAL GAMMA is a digital image quality enhancement
VR mode
function that gives a richer image by brightening the darker and more obscure portions of the image without altering the brightness of the brighter portions thereby making the entire
VCDDVD-RWDVD
image easier to see. Three digital gamma settings are avail­able to allow for differences in the images played and in brightness of the room.
1
Press
GAMMA during playback.
• The current setting appears.
2
Press ENTER to switch 1,2,3,OFF.
1
1,2,3 : Makes the dark parts brighter. OFF : Shows the original picture as recorded.
3
Press GAMMA or RETURN to exit.
NOTES:
• The setting will be saved even if the VCR/DVD is turned off.
• This function cannot be used during Rapid Play. (Refer to page 21.)
Virtual Surround
You can enjoy surround sound effect over two speakers.
1
Press MODE repeatedly until the Virtual Surround screen appears.
2
Press ENTER to set it to 1
VR mode
(Natural effect), 2 (Emphasised effect) or OFF.
3
Press MODE or RETURN to exit.
NOTES:
• The setting will be saved even if the VCR/DVD is
turned off.
• The setting will not be effective unless the sound mode
is set to STEREO. (for CDs or Video CDs only)
•Turn down the level or turn it “OFF” if the sound is dis-
torted.
• This function cannot be used during Rapid Play. (Refer
to page 21.)
VCDDVD-RWMP3CDDVD
OFF
DVD SETUP
Audio Setting
Choose appropriate settings for best sound reproduction dependent on your externally connected equipment. These settings only affect DVD playback.
1
Press SETUP in STOP mode.
2
3
4
DRC (Dynamic Range Control) :
DOWN SAMPLING :
s or B to select (CUS-
Press TOM), then press
ENTER.
• On screen menu will appear.
s or B to select
Press (AUDIO), then
K or L to select the items below, then press
Press
ENTER to confirm.
QUICK SETUP
PLAYER MENU ENGLISH
4:3 LETTER BOX
TV ASPECT DOLBY DIGITAL BITSTREAM DTS OFF MPEG DPCM
ENTER.
• Choose ON to compress the range of sound volume.
• The default setting is ON.
• DRC function is available only on
AUDIO DRC ON DOWN SAMPLING ON DOLBY DIGITAL BITSTREAM DTS OFF MPEG DPCM
the discs recorded in the Dolby Digital format.
• Choose ON to set down sampling to 48kHz.
• Choose OFF when outputting in the original sound.
• The default setting is ON.
• When playing a disc with copyright protection, the sound will be down sampled at 48kHz even if you set it to OFF.
•DOWN SAMPLING function is available only on digital output of a disc recorded in 96kHz, and when the unit is connected to another source using the digital out jack.
•DOWN SAMPLING function is available only on the
DOLBY DIGITAL :
Set to BITSTREAM when the VCR/DVD is connected to Dolby Digital Decoder. (BITSTREAM : Output by Dolby Digital) (DPCM : Convert the Dolby Digital to PCM)
• The default setting is BITSTREAM.
•You can also adjust the setting from (QUICK) setup
DTS :
Set to BITSTREAM when the VCR/DVD is connected to DTS Decoder. (BITSTREAM : Output by DTS)
• The default setting is OFF.
•You can also adjust the setting from (QUICK setup
MPEG :
5
Press
–27–
discs recorded in the Dolby Digital format.
menu.
menu).
Set to BITSTREAM when the VCR/DVD is connected to MPEG Decoder. (BITSTREAM : Output by MPEG) (DPCM : Convert the MPEG to PCM)
The default setting is DPCM.
•You can also adjust the setting from (QUICK) setup menu.
SETUP to exit.
EN
DVD SETUP
Parental Control
Parental Control prevents disc being viewed that exceed the set limit, unless a password is used. This feature allows you to prevent discs with unsuitable scenes from being played by your children.
PARENTAL LEVEL
Parental Level allows you to set the rating level of your DVDs. Playback will stop if the disc’s ratings exceed the level you set.
1
2
3
4 5
6
7
NOTES:
ALL
SETUP in STOP mode.
Press
Press s or B to select (CUS­TOM), then press
s or B to select
Press (PARENTAL), then press
ENTER.
ENTER.
Enter your four-digit password then press
K or L to select PARENTAL LEVEL, then press
Press
PARENTAL
PARENTAL LEVEL ALL
ENTER.
ENTER.
K or L to select the desired level (ALL to LEVEL1),
Press then press
ENTER.
• The rating levels continue on two menu screens. Press or L to move to the next or previous screen to find the rating level.
SETUP to exit.
Press
• When doing this for the first time, enter any 4 digits (except for 4737). This number will be used as the password from the second time onward.
•To change the password, press CHANGE at step , then press ENTER. Enter the
5
four-digit password, then press
K or L to select
ENTER.
• With some DVDs, it may be difficult to find if they are compatible with parental lock. Be sure to check if the parental lock function operates in the way that you have set.
• Record the password in case you forget it.
IF YOU FORGET THE PASSWORD
Press 4, 7, 3, 7 at step in the PARENTAL LEVEL sec­tion.
•Password will be cleared and parental level will be set to ALL.
Proceed the steps - again to set parental level.
41
742
PARENTAL CONTROL LEVELS
All parental lock is cancelled.
Level 8
DVD software of any grade (adult/general/children) can be played back.
Levels 7 to 2
Only DVD software intended for general use and children can be played back.
Level 1
Only DVD software intended for children can be played back, with those intended for adult and general use pro­hibited.
Display Setting
You can change certain aspects of the DVD display screens, on-screen messages and the display panel on the front of the VCR/DVD.
1
Press
2
3
4
K
5
NOTE:
SETUP in STOP mode.
Press
s or B
to select (CUSTOM), then press
ENTER.
• On screen menu will appear.
Press
s or B PLAY), then ENTER to confirm. Press K or L to select the below items, then press ENTER.
to select (DIS-
DISPLAY
TV ASPECT STILL MODE AUTO ANGLE ICON ON VIDEO OUT PAL
TV ASPECT :
• Press K or L for an item selection, then press ENTER.
• Select 4:3 LETTER BOX, black bars will appear at top and bottom of the screen.
• Select 4:3 PAN & SCAN for a full height picture with both sides trimmed. PAN & SCAN is only available on DVDs recorded with this option, if not LETTER BOX mode will be used.
• Select 16:9 WIDE if a wide-screen TV is connected to the VCR/DVD.
• The default setting is 4:3 LETTER BOX.
•You can also adjust the setting from (QUICK) setup menu.
STILL MODE :
• Press K or L for item selection (AUTO, FIELD or FRAME), then press ENTER.
• This adjusts the resolution of pictures while in the STILL (PAUSE) mode.
•AUTO is normally selected (default).
•If you select FIELD, pictures in the STILL mode will be stabilised although they will be coarse due to little amount of data.
•If you select FRAME, pictures in the STILL mode will be highly defined although they will be blurred due to out­put of two fields at the same time.
ANGLE ICON :
• Press ENTER repeatedly to turn Angle icon ON or OFF.
• The default setting is ON.
VIDEO OUT:
• Press ENTER repeatedly to turn video out PAL or AUTO.
• The default setting is PAL.
When playing an NTSC disc
If you have a PAL TV, select PAL; the modified PAL signal will be output.
If you have an NTSC TV or Multi system TV, select AUTO; the NTSC signal will be output.
Press SETUP to exit.
• Be sure to press SETUP, or the setting will not work.
4:3 LETTER BOX
–28–
EN
DVD SETUP
Language Setting
Language options are not available with some discs.
1
Press SETUP in STOP mode.
2
3
4
5
s or B to select (CUSTOM), then press
Press ENTER.
• On screen menu will appear.
Press
s or B to select (LAN- GUAGE), then press ENTER to confirm.
K or L to select the below
Press items, then press
ENTER.
LANGUAGE AUDIO ORIGINAL SUBTITLE OFF DISC MENU ENGLISH PLAYER MENU ENGLISH
AUDIO :
• Sets the audio language.
SUBTITLE :
• Sets the subtitle language.
DISC MENU :
• Sets the language for DVD Menu.
PLAYER MENU :
• Sets the language for the On-Screen display.
•You can also adjust the setting from (QUICK) setup menu.
K or L to select a setting, then press ENTER.
Press
• If OTHER is selected in the AUDIO, SUBTITLE or DISC MENU screen, press four-digit number to enter the code for the desired language. (Refer to the language code below.)
Language Code Language Code Language Code Language Code
Abkhazian 4748
A-B
Afar 4747 Afrikaans 4752 Albanian 6563 Amharic 4759 Arabic 4764 Armenian 5471 Assamese 4765 Aymara 4771 Azerbaijani 4772 Bashkir 4847 Basque 5167 Bengali;Bangla 4860 Bhutani 5072 Bihari 4854 Bislama 4855 Breton 4864 Bulgarian 4853 Burmese 5971 Byelorussian 4851
C-E
Cambodian 5759 Catalan 4947 Chinese [CHI] 7254 Corsican 4961 Croatian 5464 Czech 4965 Danish [DAN] 5047 Dutch [DUT] 6058 English [ENG] 5160 Esperanto 5161 Estonian 5166
F-H
Faroese 5261 Fiji 5256 Finnish [FIN] 5255 French [FRE] 5264 Frisian 5271
Galician 5358 Georgian 5747 German [GER] 5051 Greek [GRE] 5158 Greenlandic 5758 Guarani 5360 Gujarati 5367 Hausa 5447 Hebrew 5569 Hindi 5455 Hungarian [HUN] 5467
I-K
Icelandic [ICE] 5565 Indonesian 5560 Interlingua 5547 Interlingue 5551 Inupiak 5557 Irish [IRI] 5347 Italian [ITA] 5566 Japanese [JPN] 5647 Javanese 5669 Kannada 5760 Kashmiri 5765 Kazakh 5757 Kinyarwanda 6469 Kirghiz 5771 Kirundi 6460 Korean [KOR] 5761 Kurdish 5767
L-N
Laothian 5861 Latin 5847 Latvian;Lettish 5868 Lingala 5860 Lithuanian 5866 Macedonian 5957 Malagasy 5953 Malay 5965 Malayalam 5958
• Only the languages suppor ted by the disc can be select­ed.
6
Press
SETUP to exit.
NOTE:
• Language Setting for Audio and Subtitle is not available with some discs. Then use
AUDIO and SUBTITLE. (Refer
to pages 25 and 26.)
Returning all selections of SETUP
for PARENTAL)
to their default settings
(except
This allows you to return all selections of SETUP (except for PARENTAL) to their default settings.
1
2
3
SETUP in STOP mode.
Press
Press
s or B to select (INI-
TIALIZE), then press
Select YES, then press
ENTER.
ENTER to
QUICK SETUP
PLAYER MENU ENGLISH TV ASPECT
4:3 LETTER BOX DOLBY DIGITAL BITSTREAM DTS OFF MPEG DPCM
confirm.
4
Press
NOTE:
Maltese 5966 Maori 5955 Marathi 5964 Moldavian 5961 Mongolian 5960 Nauru 6047 Nepali 6051 Norwegian [NOR] 6061
Occitan 6149 Oriya 6164 Oromo(Afan) 6159 Panjabi 6247 Pashto;Pushto 6265 Persian 5247 Polish 6258 Por tuguese [POR] 6266 Quechua 6367 Rhaeto-Romance 6459 Romanian [RUM] 6461 Russian [RUS] 6467
Samoan 6559 Sangho 6553 Sanskrit 6547 Scots Gaelic 5350 Serbian 6564 Serbo-Croatian 6554
SETUP to exit.
• When you cancel to initialize at step , select NO.
3
Swahili 6569 Swedish [SWE] 6568
Tagalog 6658 Tajik 6653 Tamil 6647 Tatar 6666 Telugu 6651
O-R
Thai 6654 Tibetan 4861 Tigrinya 6655 Tonga 6661 Tsonga 6665 Tu r kish [TUR] 6664 Tu r kmen 6657 Tw i 6669
Ukrainian 6757 Urdu 6764 Uzbek 6772 Vietnamese 6855
S
Volapuk 6861 Welsh 4971 Wolof 6961 Xhosa 7054 Yiddish 5655 Yo r uba 7161 Zulu 7267
Initialize? NO YES
T
U-Z
INITIALIZE
Sesotho 6566 Setswana 6660 Shona 6560 Sindhi 6550 Singhalese 6555 Siswat 6565 Slovak 6557 Slovenian 6558 Somali 6561 Spanish [SPA] 5165 Sundanese 6567
If you choose a Language that has a 3 letter language code, the code will be displayed every time you change the Audio or Subtitle language setting on pages 25 and 26. If you choose any other languages, ‘---’ will be dis­played instead. (3 letter language code is written in bracket.)
–29–
EN
TROUBLESHOOTING GUIDE
If the VCR/DVD does not perform properly when operated as instructed in this Operation Manual, check the VCR/DVD, con­sulting the following checklist.
Problem Solution No power –Check if the AC power cord is properly connected. No picture –Check if the TV is switched on.
Distorted picture –Sometimes a small amount of picture distortion may appear.
Completely distorted picture or –Connect VCR/DVD directly to the TV. black/white picture with DVD –Make sure the disc is compatible with the VCR/DVD. No sound or distorted sound –Adjust the volume.
No audio at digital output –Check the digital connections.
No DTS audio at analogue output. –Use a COAXIAL DIGITAL AUDIO OUT jack when outputting the
Picture freezes momentarily –Check the disc for fingerprints/scratches and during playback clean with a soft cloth wiping from centre to edge. Disc cannot be played –Ensure the disc label is facing up.
No return to start-up screen when disc is removed –Reset the VCR/DVD by switching the VCR/DVD off, then on again. The VCR/DVD does not respond to – the
remote control
Buttons do not work or VCR/DVD stops –To completely reset the VCR/DVD, unplug the AC responding cord from the AC outlet for 5-10 seconds. VCR/DVD does not respond to some –Operations may not be permitted by the disc. operating commands during playback. Refer to the instructions of the disc. VCR/DVD cannot not read CDs/DVDs –Use a commonly available cleaning CD/DVD to clean the lens
The VCR does not record a TV programme. –Make sure the tape has a erase-prevention tab.
The VCR does not perform a timer recording. –Make sure the start and the stop recording times are set correctly.
The motor rotates even when tape –To enable quick play mechanism, the motor will rotate for about 5 playback is stopped. minutes. This is normal. You cannot insert a tape. –Insert a tape with window side up and the erase-prevention tab
You cannot remove a tape. –Make sure the power plug is completely connected to a power
–Check if the cable is connected to the correct device.
(See “Connecting to a TV or a stereo TV”)
This is not a malfunction.
–Check that the speakers are connected correctly. –Check if the cable is connected to the correct device.
(See “Connecting to a TV or a stereo TV”)
–Check if the audio format of the selected audio language matches
your receiver capabilities.
DTS audio.
–Check if the disc is defective by trying another disc. –Handle a disc with special care so that it does not have fingerprints,
scratches or dusts on its surface.
Aim the remote control directly at the sensor on the front of the
VCR/DVD. –Reduce the distance to the VCR/DVD. –Replace the batteries in the remote control. –Re-insert the batteries with their polarities (+/– signs) as indicated.
before sending the VCR/DVD for repair.
–Make sure this VCR/DVD is in VCR mode.
–Make sure the tape has a erase-prevention tab. –Make sure the clock is set. –This VCR/DVD may not perform or continue a timer recording if the
power fails for more than 1 hour.
facing you. –Gently push the centre of the tape when putting into the cassette
compartment.
outlet.
NOTES:
• Some functions are not available in specific modes, but this is not a malfunction. Read the description in this Operation Manual for details on correct operations.
• Playback from a desired track and random playback are not available during programme playback.
• Some functions are prohibited on some discs.
If you are unable to remedy a problem by following these hints, consult your dealer or service centre.
–30–
EN
SPECIFICATIONS
ReWritable
PRODUCT TYPE
DVD Player with Video Cassette recorder
NUMBER OF VIDEO HEADS
4
VIDEO SIGNAL STANDARD
PAL colour system
AUDIO RECORDING SYSTEM
1 Stationary head for liner audio 2 Rotary heads for Hi-Fi stereo
CHANNEL COVERAGE
E2 - E69
TIMER BACKUP
60 minutes
DISCS (PLAYBACK COMPATIBILITY)
DVD Video / Audio CD / Video CD / CD-RW / R DVD-RW / R, DVD+RW / R
FREQUENCY RESPONSE
DVD (linear sound) : 20 Hz to 20 kHz (sample rate: 48 kHz)
20 Hz to 44 kHz (sample rate: 96 kHz)
CD : 20 Hz to 20 kHz
SIGNAL-TO-NOISE RATIO (S/N RATIO)
CD : 110 dB (JEITA)
DYNAMIC RANGE
DVD (linear sound) : 90 dB CD : 90 dB (JEITA)
• Designs and specifications are subject to change without notice.
• If there is a discrepancy between languages, the default language will be English.
TOTAL DISTORTION FACTOR
DVD : 1KHz 0.008% (JEITA) CD : 1KHz 0.008% (JEITA)
WOW AND FLUTTER
Below the measurement limitation (+/-0.001% W PEAK) (JEITA)
CONNECTIONS
Front panel:
Video input Audio input
Rear panel:
Audio/Video Output/Input S-Video output Mini DIN 4-pin jack (75 Ω) Analog audio output RCA connector
Coaxial digital audio output One pin jack, 500mVpp (75 Ω)
POWER SOURCE
220-240 V ~ +/- 10%, 50Hz +/- 0.5%
POWER CONSUMPTION
30W (standby: 5W)
OPERATING TEMPERATURE
5°C to 40°C
DIMENSIONS
W: 435mm H: 94mm D: 233mm
WEIGHT
Approx 3.2kg
RCA connector [ 1 RCA connector [ 2
21-pin scart terminal [ 2
[ 2 channel, one right channel) 2 Vrms (47 kΩ)
(one left
MAINTENANCE
Cleaning the Cabinet
• Use a soft cloth slightly moistened with a mild detergent solution. Do not use a solution containing alcohol, spirits, ammonia or abrasives.
Cleaning Discs
• When a disc becomes dir ty, clean it with a cleaning cloth. Wipe the disc from the centre out. Do not wipe in a circular motion.
• Do not use solvents such as benzine, thinner, commercially available cleaners, detergent, abrasive cleaning agents or antistatic spray intended for analogue records.
Cleaning the disc lens
• If the VCR/DVD still does not perform properly when it is operated while referring to the relevant sections and to “TROU­BLESHOOTING GUIDE” in this Operation Manual, the laser optical pickup unit may be dirty. Consult your dealer or an authorised Service Centre for inspection and cleaning of the laser optical pickup unit.
Disc Handling
• Use discs which have the following logos on them. (Optical audio digital discs.)
ReWritable
• Handle the discs so that fingerprints and dust do not adhere to the surfaces of the discs.
• Always store the disc in its protective case when it is not used.
Make your contribution to the environment!!!
• Used up batteries do not belong in the dust bin.
• You can dispose of them at a collection point for used up batteries or special waste. Contact your council for details.
Recordable
–31–
EN
SHARP CORPORATION
1VMN20161
H97D3ED★★★
9HS1VMN20161
Loading...