VIDEO CD MINI SYSTEM
MINI-CHAÎNE CD VIDÉO
SISTEMA MINI VÍDEO CD
MODELMODELO
MODÈLE
CD-M10000V
SPEAKER SYSTEM
ENCEINTES ACOUSTIQUES
SISTEMA DE ALTAVOCES
MODELMODELO
MODÈLE
CP-M10000
OPERATION MANUALMANUAL DE MANEJO
MODE D’EMPLOI
CDM10000V_FRONT01.10.30, 9:491
NTSC/PAL
ENGLISH
FRANÇAIS
ESPAÑOL
Please refer to pages E-1 to E-42.
Se reporter aux pages F-1 à F-42.
Consulte las páginas S-1 a S-42.
SHARP CORPORATION
CD-M10000V
ENGLISH
ENGLISH
Introduction
Thank you for purchasing this SHARP product. To obtain the best performance from
this product, please read this manual carefully. It will guide you in operating your
SHARP product.
When the ON/STAND-BY button is set at STAND-BY position, mains voltage is still
present inside the unit. When the ON/STAND-BY button is set at STAND-BY position, the unit may be brought into operation by the timer mode or remote control.
z
This unit contains no user serviceable parts. Never remove covers unless qualified
to do so. This unit contains dangerous voltages, always remove mains plug from
the socket before an y service operation and when not in use for a long period.
z
To prevent fire or shock hazard, do not expose this appliance to dripping or splashing. No objects filled with liquids, such as vases, shall be placed on the apparatus.
Accessories
Please confirm that the following accessories are included.
CD-M10000V
ENGLISH
CAUTION
z
This product is classified as a CLASS 1 LASER product.
z
Use of controls, adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure.
As the laser beam used in this compact disc player is harmful to the eyes, do not
attempt to disassemble the cabinet. Refer servicing to qualified personnel only.
Laser Diode Properties
Material : Ga AIAs
Wavelength: 780 nm
Emission Duration: continuous
Laser Output: max. 0.6 mW
Note:
Audio-visual material may consist of copyrighted works which must not be recorded
without the authority of the owner of the copyright. Please refer to the relevant laws in
your country.
Remote control 1"AA" size battery (UM/SUM-3, R6,
HP-7 or similar) 2
AM loop aerial 1FM aerial 1
Blue
Black
Wire for main speaker 2Wire for woofer 2
Video cable 1
Note:
Only the above accessories are included.
1
- Special notes / Accessories -
2
Important Instruction
3
4
5
6
7
E-2
CD-M10000V(X)E1.fm01/10/30
CD-M10000V
ENGLISH
General Information
Precautions
General
„
z
Please ensure that the equipment is positioned in a well ventilated area and
ensure that there is at least 10 cm (4") of free space along the sides, top and back
of the equipment.
10 cm (4")10 cm (4")
10 cm (4")
z
Use the unit on a firm, level surface free from vibration.
z
Keep the unit away from direct sunlight, strong magnetic fields, excessive dust,
humidity and electronic/electrical equipment (home computers, facsimiles, etc.)
which generates electrical noise.
z
Do not place anything on top of the unit.
z
Do not expose the unit to moisture, to temperatures higher than 60°C (140°F) or to
extremely low temperatures.
z
If your system does not work properly, disconnect the AC power lead from the wall
socket. Plug the AC power lead back in, and then turn on your system.
z
In case of an electrical storm, unplug the unit for safety.
z
Hold the AC power plug by the head when removing it from the wall socket, as
pulling the lead can damage internal wires.
z
Do not remove the outer cover, as this may result in electric shock. Refer
- Precautions -
internal service to your local SHARP service facility .
z
The ventilation should not be impeded by covering the ventilation openings with
items, such as newspapers, tablecloths, curtains, etc.
z
No naked flame sources, such as lighted candles, should be placed on the apparatus.
z
Attention should be drawn to the environmental aspects of battery disposal.
z
This unit should only be used within the range of 5°C - 35°C (41°F - 95°F).
10 cm (4")
Volume control
„
The sound level at a given volume setting dep ends on speaker efficiency, location,
and various other factors. It is advisable to avoid exposure to high volume levels,
which occurs whilst turning the unit on with the volume control setting up high, or
whilst continually listening at high volumes.
Condensation
„
Sudden temperature changes, storage or operation in an extremely humid environment
may cause condensation inside the cabinet
(CD pickup, tape heads, etc.) or on the transmitter on the remote control.
Condensation can cause the unit to malfunction. If this happens, leave the power on with
no disc (or cassette) in the unit until normal
playback is possible (about 1 hour). Wipe off
any condensation on the transmitter with a soft
cloth before operating the unit.
Care of compact discs
„
Compact discs are fairly resistant to damage, however mistracking can occur due to
an accumulation of dirt on the disc surface. Follow the guidelines below for maximum
enjoyment from your CD collection and player.
z
Do not write on either side of the disc, par ticularly the non-label side from which
signals are read. Do not mark this surface.
z
Keep your discs away from direct sunlight, heat, and excessive moisture.
z
Always hold the CDs by the edges. Fingerprints, dirt, or water on the CDs can
cause noise or mistracking. If a CD is dirty or does not play properly , clean it with a
soft, dry cloth, wiping straight out from the centre, along the radius.
E-3
Warning:
The voltage used must be the same as that specified on this unit. Using this product
with a higher voltage other than that which is specified is dangerous and ma y result in
a fire or other type of accident causing damage. SHARP will not be held responsible
for any damage resulting from use of this unit with a voltage other than that which is
specified.
This product is equipped with a cooling fan inside, which begins to run at a specified
volume level for better heat radiation.
Reference page
E-5
11
98
8
CD-M10000V(X)E1.fm01/10/30
Main speaker
„
211
1.Woofer
2.Tweeter
3.Bass Reflex Duct
4.Speaker Terminals
Woofer
„
CD-M10000V
ENGLISH
Placing the speaker system:
There is no distinction between the right and the left speakers.
Main speaker (Left)Main speaker (Right)
3
4
Woofer (Left)Woofer (Right)
Notes:
z
The main speakers are magnetically shielded.
Therefore, they do not affect the display even you use them near the TV. However,
some colour variation may occur, depending on the type of TV used.
If colour variation occurs...
Turn off the TV (from the power switch).
After 15 - 30 minutes, turn the TV on again.
If the colour variation is still present...
Move the speakers further away from the TV.
z
If any kind of magnet or an electromagnet is placed too close to the TV and the system, irregular colours may appear on the TV screen.
1
1
1.Woofer
2.Bass Reflex Duct
3.Speaker Terminals
General Information
- Controls and indicators -
2
3
4
5
2
3
Woofer grilles are removable:
Make sure nothing comes into contact with the speaker
diaphragms when you remove the speaker grilles.
Note:
The speaker grilles on the main speakers are not removable.
Caution:
The metallic handles on the both sides of the speaker grill on the woofer are decorations. Do not carry the woofers by them as this may damage the woofers.
Buttons with " " mark in the illustration can be operated on the remote control
only.
Other buttons can be operated both on the main unit and the remote control.
Reference page
E-7
CD-M10000V(X)E1.fm01/10/30
Remote control
Battery installation
„
1 Open the battery cover.
2 Insert the batteries according to the direction indicated in the bat-
tery compartment.
When inserting or removing the batteries, push them towards the battery termi-
nals.
3 Close the battery cover.
Precautions for battery use:
z
Replace all old batteries with new ones at the same time.
z
Do not mix old and new batteries.
z
Remove the batteries if the unit will not be used for long periods of time. This will
prevent potential damage due to battery leakage.
Caution:
z
Do not use rechargeable batteries (nickel-cadmium battery, etc.).
z
Installing the batteries incorrectly may cause the unit to malfunction.
Notes concerning use:
z
Replace the batteries if the operating distance is reduced or if the operation
becomes erratic. Purchase 2 "AA" size batteries (UM/SUM-3, R6, HP-7 or similar).
z
Periodically clean the transmitter on the remote control and the sensor on the unit
with a soft cloth.
z
Exposing the sensor on the unit to strong light may interfere with operation.
Change the lighting or the direction of the unit.
z
Keep the remote control away from moisture, heat, shock, and vibrations.
Test of the remote control
„
Check the remote control after checking all connections have been made correctly.
(See pages 9 - 11.)
Face the remote control directly to the remote sensor on the unit.
The remote control can be used within the range shown below:
Press the ON/STAND-BY button. Does the power turn on? Now, you can enjoy the
music.
Remote sensor
0.2 m - 6 m
(8" - 20')
CD-M10000V
ENGLISH
Preparation for Use
- Remote control -
1
2
3
4
5
6
7
E-8
CD-M10000V(X)E1.fm01/10/30
CD-M10000V
ENGLISH
Preparation for Use
System connections
Main speaker (Right)
AM loop aerial
- System connections -
Woofer (Right)
FM aerial
Main speaker (Left)
Woofer (Left)
To a wall socket
(See page 11.)
Aerial connection
„
Supplied FM aerial:
Connect the FM aerial wire to the FM 75 OHMS
terminal and position the FM aerial wire in the direction where the strongest signal can be received.
Supplied AM loop aerial:
Connect the AM loop aerial wire to the AM
LOOP socket. Position the AM loop aerial for
optimum reception. Place the AM loop aerial on
a shelf, etc., or attach it to a stand or a wall with
screws (not supplied).
Note:
Placing the aerial on the unit or near the AC power lead may cause noise pickup.
Place the aerial away from the unit for better reception.
Installing the AM loop aerial:
< Assembling >< Attaching to the wall >
Wall Screws (not supplied)
External FM aerial:
Use an external FM aerial if you require better reception. Consult your dealer.
External
FM aerial
75 ohm
coaxial
cable
E-9
Note:
When an external FM aerial is used, disconnect the supplied FM aerial wire.
CD-M10000V(X)E1.fm01/10/30
Speaker connection
„
Main speakers:
Connect the black wire to the MAIN (-) terminal, and the blue wire to the MAIN (+) terminal.
Woofers:
Connect the black wire to the WOOFER (-) terminal, and the red wire to the
WOOFER (+) terminal.
Main speaker (Right)Main speaker (Left)
Woofer
(Right)
Red
Black
Blue
Caution:
z
Connect the speaker wires to the speakers first, then to the unit.
z
Never mistake the MAIN and the WOOFER terminals. The unit or the speakers
may be damaged.
z
Only the included speakers should be used with this product. Do not use other
speakers with this unit or use the supplied speaker s with other units.
z
Do not mistake the right and the left channels. The right speaker is the one on the
right side when you face the unit.
z
Do not let the bare speaker wires touch each other.
z
Do not allow any objects to fall into or to be placed in the bass reflex ducts.
z
Do not stand or sit on the speakers. You may be injured.
Woofer
(Left)
Bi-amp system:
This unit employs the bi-amp system in which the low frequency range power amplifier drives woofers, and mid-to-high frequency range power amplifier drives woofers
and tweeters of the main speaker respectively. Clearer sound will be assured by
amplifying two frequency bands individually using two characteristically different
amplifiers.
Mid-to-high range
Woofer
Tweeter
Woofer
Woofer
TV/monitor connection
„
If the TV/monitor has a video input, connect it to VIDEO OUT socket on the rear of
the unit.
Power amplifier
Power amplifier
(200 Hz - 20 kHz)
Pre-amplifier
L-ch
Pre-amplifier
Ultra-low range
(60 Hz - 200 Hz)
TV
To video
input socket
CD-M10000V
ENGLISH
1
- System connections -
2
Preparation for Use
3
IncorrectIncorrect
Video cable
Note:
If the TV/monitor does not have a video input, the VIDEO OUT socket on the unit
should be connected to a VCR with a video input, which in turn should be connected
to the TV/monitor through the TV ANTENNA/CABLE input. (Be sure to turn on the
VCR, and set the VCR's input mode to "auxiliary".)
CD-M10000V(X)E1.fm01/10/30
4
5
6
7
E-10
CD-M10000V
ENGLISH
System connections (continued)
Preparation for Use
Setting the AC voltage selector
„
Check the setting of the AC voltage selector located on the rear panel before plugging the unit into a wall socket. If necessary, adjust the selector to corr espond to the
AC power voltage used in your area.
Turn the selector with a screwdriver until the appr opria te voltage number appears in the window (110 V, 127 V, 220 V or 230 V - 240 V AC).
Connecting the AC power lead
„
After making all connections, plug the unit. If you plug the unit first,
the unit will enter the demonstration mode (see page 12).
Note:
Unplug the AC power lead from the wall socket if the unit will not be in use for a prolonged period of time.
AC Plug Adaptor
In areas (or countries) where a wall socket as shown in illustration is used, connect
the unit using the AC plug adaptor supplied with the unit, as illustrated. The AC plug
adaptor is not included in areas where the wall socket and AC power plug can be
directly connected (see illustration ).
- System connections -
Setting the FM/AM span selector
„
The International Telecommunication Union (ITU) has established that member coun-
1
2
tries should maintain either a 100 kHz or a 50 kHz interval between broadcasting frequencies of FM stations and 10 kHz or 9 kHz for AM station. The illustration shows
the 50/9 kHz zones (regions 1 and 3), and the 100/10 kHz zone (region 2).
Before using the unit, set the SPAN SELECTOR switch (on the rear panel) to the
interval (span) of your area.
To change the tuning zone:
1 Press the ON/STAND-BY button to enter the stand-by mode.
2 Set the SPAN SELECTOR switch (on the rear panel) as follows.
z
For 50 kHz FM interval (9 kHz in AM) 50/9
z
For 100 kHz FM interval (10 kHz in AM) 100/10
3 Whilst pressing down the button and the MONSTER-BASS button, press the ON/
STAND-BY button until "CLEAR AL" appears.
Caution:
This operation will erase all data stored in memory including clock, timer settings,
tuner preset, and CD programme.
E-11
CD-M10000V(X)E2.fm01/10/30
General control
FLAT
ROCK
POPS
JAZZ
CLASSIC
VOCAL
The sound is not modified.
Bass and treble are emphasised.
Bass and treble are slightly emphasised.
Treble is cut a little.
Treble is reduced a lot.
Vocals (midrange tones) are emphasised.
To change the display brightness (2 lev els)
„
You can switch the display brightness by pressing the DIMMER button.
CD-M10000V
ENGLISH
Demonstration mode
„
The first time the unit is plugged in, the unit will enter
the demonstration mode. You will see words scroll.
To cancel the demonstration mode:
When the unit is in the power stand-by mode (demonstration mode), press the MONSTER-BASS button. The demonstration mode will be cancelled and the display will
disappear.
To return to the demonstration mode:
When the unit is in the power stand-by mode, press the MONSTER-BASS button
again.
Note:
When the power is on, the MONSTER-BASS button can be used to select the extra
bass mode.
Volume control
„
Main unit operation:
When the VOLUME control is turned clockwise, the volume will increase. When it is
turned anti-clockwise, the volume will decrease.
Remote control operation:
Press the VOLUME button to increase the volume and the VOLUME button for
decreasing.
Bass control
„
When the power is first turned on, the unit will enter the monster bass
mode which emphasises the bass frequencies, and the monster bass
mode indicator will light up. To cancel this, press the MONSTER-BASS
(MONSTER BASS) button.
Equalizer
„
When the EQUALIZER (EQ-MODE) button is pressed, the current mode setting will
be displayed. To change to a different mode, press the EQUALIZER (EQ-MODE) button repeatedly until the desired sound mode appears.
DimmedBrightened
012 2930MAXIMUM
.....
- General control -
Basic Operation
1
2
3
4
To turn th e power on
„
Press the ON/STAND-BY button to turn the power on.
To set the unit to stand-by mode:
Press the ON/STAND-BY button again.
5
6
7
E-12
CD-M10000V(X)E2.fm01/10/30
Loading...
+ 30 hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.