Page 1
CD-DP900E
MINI COMPONENT SYSTEM
Accessories
1
1
Remote control × 1 AM loop aerial × 1
This Quick Guide will help you to correctly
install and operate your system.
If you require any advice or assistance regarding
your Sharp product, please visit our web-site
www.sharp.co.uk/support.
Customers without Internet access may telephone
08705 274277 during office hours (or (01) 676 0648
if telephoning from Ireland).
0101
FM aerial × 1
Remote control battery installation
2
2
Use 2 “AA” size batteries (UM/SUM-3, R6, HP-7 or similar). Batteries are not included.
Remove the
123
battery cover.
Insert the batteries
as shown.
– 1 –
Replace the cover.
TINSZ0823AWZZ A0201.HK
CD-DP900E_QG 02.1.16, 11:46 AM1
Page 2
System connections
3
3
Before turning the power on, be sure to remove the transport screw
on the back of the unit using a flat head screwdriver or a coin.
FM aerial
AM loop aerial
Surround speaker
(Right)
Front speaker
(Right)
Wall socket
(AC 230-240 V, 50 Hz)
Centre speaker
Surround speaker (Right) Surround speaker (Left)
Centre speaker
Surround speaker
(Left)
Front speaker
(Left)
RCA lead
(not supplied)
Front speaker (Right)
Red
Black
CD-DP900E_QG 02.1.16, 11:46 AM2
Grey
Orange
Front speaker (Left)
– 2 –
To the line
output sockets
VCR, DVD, etc.
TV
Page 3
Turn on your system
4
4
The first time the unit is plugged
in, the unit will enter the demonstration mode. You will see words
scroll.
Press the
1
EQUALIZER/X-BASS/
DEMO button to cancel
the demonstration mode.
Listening to a CD (CDs)
1
12 cm (5")
2
8 cm (3")
3
4
Press the
2
ON/STAND-BY button
to turn the power on.
Press the CD button.
Press the
open the disc tray.
Place the CD(s) on the disc tray, label side up.
When loading a third disc, press the
DISC SKIP button to turn the disc
tray, then place the CD in the open
position.
Press the
close the disc tray.
7 7
7 OPEN/CLOSE button to
7 7
7 7
7 OPEN/CLOSE button to
7 7
1
2, 4
6
3, 5
Listening to the radio
1
2
FM stereo mode indicator
FM stereo receiving indicator
5
6
1
2
To select the CD you want to listen
to first, press the DISC SKIP button.
Press the
back.
Press the TUNER (BAND) button repeatedly to select the desired frequency band (FM or AM).
Press the TUNING/TIME (
button to tune in to the desired station.
When the TUNING/TIME button is
pressed for more than 0.5 seconds,
scanning will start automatically and
the tuner will stop at the first receivable broadcast station.
To receive an FM stereo transmission:
Press the TUNER (BAND) button to display the
“ST” indicator.
jj
● “
j” will appear when an FM broadcast is in
jj
stereo.
0 / R 0 / R
0 / R button to start play-
0 / R 0 / R
XX
WW
X or
W)
XX
WW
CD-DP900E_QG 02.1.16, 11:47 AM3
– 3 –
Page 4
Listening to a cassette tape (TAPE 1 or TAPE 2)
1
3
2
4
3
4
TAPE 1 TAPE 2
■ If trouble occurs
When this product is subjected to strong external interference
(mechanical shock, excessive static electricity, abnormal supply voltage due to lightning, etc.) or if it is operated incorrectly, it
may malfunction.
If such a problem occurs, do the following:
1. Set the unit to the stand-by mode and turn the power
on again.
If the unit is not restored in the previous operation, un-
2.
plug and plug in the unit, and then turn the power on.
Note:
If neither operation above restores the unit, clear all the memory
by resetting it.
Open the cassette door by pushing
the area marked “
Load a cassette into the TAPE 1 or
TAPE 2 cassette compartment with
the side to be played facing toward
you.
Press the TAPE (1
lect the cassette you want to listen
to.
Press the
back.
0 / R0 / R
0 / R button to start play-
0 / R0 / R
7 7
7 PUSH EJECT”.
7 7
VV
V 2) button to se-
VV
■ Clearing all the memory (reset)
1. Press the ON/STAND-BY button to enter the power
stand-by mode.
Whilst pressing down the CLOCK button and the
2.
EQUALIZER/X-BASS/DEMO button, press the ON/
STAND-BY button until “CLEAR AL” appears.
Caution:
This operation will erase all data stored in memory including
clock, timer settings, tuner preset, and CD programme.
■
Maintenance
● Dirty heads, capstans or pinch rollers can cause poor
sound and tape jams. Clean these parts with a cotton swab
moistened with commercial head/pinch roller cleaner or
isopropyl alcohol.
● When cleaning the heads, pinch rollers, etc., unplug the
unit which contains high voltages.
● After long use, the deck’s heads and capstans may become magnetised, causing poor sound. Demagenetise
these parts once every 30 hours of playing/recording time
by using a commercial tape head demagnetiser. Read the
demagnetiser’s instructions carefully before use.
● Clean the dust or stain on the CD pickup lens using a commercial cleaning disc (brush type).
– 4 –
TAPE 1
TAPE 2
A Playback head
B Capstan
C Pinch roller
D Erase head
E Recording/Playback head
B
A
E
D
C
C
B
CD-DP900E_QG 02.1.16, 11:47 AM4
Page 5
documentation manual, user maintenance, brochure, user reference, pdf manual
This file has been downloaded from:
User Manual and User Guide for many equipments like mobile phones, photo cameras, monther board, monitors, software, tv, dvd, and othes..
Manual users, user manuals, user guide manual, owners manual, instruction manual, manual owner, manual owner's, manual guide,
manual operation, operating manual, user's manual, operating instructions, manual operators, manual operator, manual product,
Loading...