Sharp CDBA-1300-H Service manual
CD-BA1300H
SERVICE MANUAL
No. S5040CDA1300H
MINI COMPONENT SYSTEM
This Service Manual is for the CD-BA1300H, which is a minormodification model of the CD-BA1200H. This manual, therefore,
describes only the changed points from the service manual. Please
refer to the CD-BA1200H service manual (No.S4029CDBA1200)
together with this manual.
CD-BA1200H
Page
IMPORTANT SERVICE NOTES (FOR U.K. ONLY)......... 3
DISASSEMBLY................................................................. 9
REMOVING AND REINSTALLING THE MAIN PARTS.. 12
ADJUSTMENT................................................................ 13
WAVEFORMS OF CD CIRCUIT..................................... 16
TROUBLESHOOTING (CD SECTION) .......................... 37
FUNCTION TABLE OF IC .............................................. 41
FL DISPLAY.................................................................... 47
MODEL
CD-BA1300H Mini Component System consisting of
CD-BA1300H (main unit) and CP-BA1300H (speaker system).
• In the interests of user-safety the set should be restored to its
original condition and only parts identical to those specified be
used.
• Note for users in U.K.
Recording and playback of any material may require consent
which SHARP is unable to give. Please refer particularly to the
provisions of Copyright Act 1956, the Dramatic and Musical
Perfomers Protection Act 1956, the Performers Protection Acts
1963 and 1972 and to any subsequent statutory enactments and
orders.
CD-BA1300H
CONTENTS
Page
SAFETY PRECAUTION FOR SERVICE MANUAL ........................................................................................................... 2
SPECIFICATIONS ............................................................................................................................................................. 3
NAMES OF PARTS ........................................................................................................................................................... 4
OPERATION MANUAL ...................................................................................................................................................... 6
QUICK GUIDE ................................................................................................................................................................... 7
DISASSEMBLY.................................................................................................................................................................. 9
NOTES ON SCHEMATIC DIAGRAM .............................................................................................................................. 10
BLOCK DIAGRAM ........................................................................................................................................................... 11
SCHEMATIC DIAGRAM / WIRING SIDE OF P.W.BOARD............................................................................................. 14
VOLTAGE ........................................................................................................................................................................ 30
REPLACEMENT PARTS LIST/EXPLODED VIEW
PACKING METHOD (FOR U.K. ONLY)
This document has been published to be used
SHARP CORPORATION
– 1 –
for after sales service only.
The contents are subject to change without notice.
CD-BA1300H
SAFETY PRECAUTION FOR
SERVICE MANUAL
Precaution to be taken when replacing and servicing the
Laser Pickup.
The AEL (Accessible Emission Level) of Laser Power Output
for this model is specified to be lower than Class I Requirements.
However, the following precautions must be observed during
servicing to protect your eyes against exposure to the Laser
beam.
(1) When the cabinet has been removed, the power is turned
on without a compact disc, and the Pickup is on a position
outer than the lead-in position, the Laser will light for several
seconds to detect a disc. Do not look into the Pickup Lens.
(2) The Laser Power Output of the Pickup inside the unit and
replacement service parts have already been adjusted prior
to shipping.
(3) No adjustment to the Laser Power should be attempted
when replacing or servicing the Pickup.
(4) Under no circumstances look directly into the Pickup Lens
at any time.
(5) CAUTION - Use of controls or adjustments, or performance
of procedures other than those specified herein may result
in hazardous radiation exposure.
(For U.K.)
(Except for U.K.)
Laser Diode Properties
Material: GaAIAs
Wavelength: 780 nm
Emission Duration: continuous
Laser Output: max. 0.6 mW
– 2 –
CAUTION-INVISIBLE LASER RADIATION WHEN OPEN. DO NOT STARE INTO
BEAM OR VIEW DIRECTLY WITH OPTICAL INSTRUMENTS.
VARNING-OSYNLIG LASERSTRALNING NAR DENNA DEL AR OPPNAD. STIRRA
EJ IN I STRALEN OCH BETRAKTA EJ STRALEN MED OPTISKA INSTRUMENT.
ADVERSEL-USYNLIG LASERSTRALING VED ABNING. SE IKKE IND I
STRALEN-HELLER IKKE MED OPTISKE INSTRUMENTER.
VARO! AVATTAESSA OLET ALTTIINA NAKYMATON LASERSATEILYLLE.
ALA TUIJOTA SATEESEEN ALAKA KATSO SITA OPTISEN LAITTEEN LAPI.
VARNING-OSYNLIG LASERSTRALNING NAR DENNA DEL AR OPPNAD.
STIRRA EJ IN I STRALEN OCH BETRAKTA EJ STRALEN GENOM OPTISKT
INSTRUMENT.
ADVERSEL-USYNLIG LASERSTRALING NAR DEKSEL APNES. STIRR IKKE
INN I STRALEN ELLER SE DIREKTE MED OPTISKE INSTRUMENTER.
VAROITUS! LAITTEEN KÄYTTÄMINEN MUULLA KUIN
TÄSSÄ
KÄYTTÖOHJEESSA MAINITULLA TAV ALLA SAATTAA
ALTISTAA KÄYTTÄJÄN TURVALLISUUSLUOKAN 1
YLITTÄVÄLLE NÄKYMÄTTÖMÄLLE LASERSÄTEILYLLE.
VARNING - OM APPARA TEN ANVÄNDS PÅ ANNA T SÄTT
ÄN I DENNA BRUKSANVISNING SPECIFICERAS. KAN
ANVÄNDAREN UTSÄTTAS FÖR OSYNLIG
LASERSTRÅLNING, SOM ÖVERSKRIDER GRÄNSEN
FÖR LASERKLASS 1.
CD-BA1300H
CD-BA1300H
FOR A COMPLETE DESCRIPTION OF THE OPERATION OF THIS UNIT, PLEASE REFER
TO THE OPERATION MANUAL.
SPECIFICATIONS
General
Power source:
Power
consumption:
Dimensions:
Weight:
AC 230 V, 50 Hz
47 W
Width; 270 mm (10-5/8")
Height; 300 mm (11-13/16")
Depth; 373 mm (14-11/16")
5.2 kg (11.4 lbs.)
Amplifier section
Output power:
(For U.K.)
Output power:
(Except for U.K.)
Output terminals:
RMS; 40 W (20 W + 20 W) (10 %
T.H.D.)
RMS; 28 W (14 W + 14 W) (0.9 %
T.H.D.)
PMPO; 128 W
MPO; 64 W (32 W + 32 W) (DIN 45
324)
RMS; 40 W (20 W + 20 W) (DIN 45
324)
RMS; 28 W (14 W + 14 W) (DIN 45
500)
Speakers; 6 ohms
Headphones; 16 - 50 ohms (rec-
ommended; 32 ohms)
Compact disc player section
Cassette deck section
Frequency
response:
Signal/noise ratio:
Wow and flutter:
(For U.K.)
Wow and flutter:
(Except for U.K.)
CP-BA1300H
Type:
Maximum input
power:
Rated input power:
Impedance:
Dimensions:
Weight:
Specifications for this model are subject to change without
prior notice.
50 - 14,000 Hz (Normal tape)
55 dB (TAPE 1, playback)
50 dB (TAPE 2, recording/playback)
0.3 % (WRMS)
0.35 % (DIN 45 511)
2-way [13 cm (5-1/4") woofer and 5
cm (2") tweeter]
40 W
20 W
6 ohms
Width; 220 mm (8-11/16")
Height; 300 mm (11-13/16")
Depth; 217 mm (8-9/16")
2.6 kg (5.7 lbs.)/each
Type:
Signal readout:
D/A converter:
Frequency
response:
Dynamic range:
Tuner section
Frequency range:
3-disc multi-play compact disc
player
Non-contact, 3-beam semi-conductor laser pickup
1-bit D/A converter
20 - 20,000 Hz
90 dB (1 kHz)
FM; 87.5 - 108 MHz
AM; 522 - 1,620 kHz
– 3 –
CD-BA1300H
(
CD-BA1300H
Front panel
NAMES OF PARTS
2
1
8
9
10
11
12
16 17 19
18
76543
20
2122 23
24 25
13
14
15
26 27 28 29 30 31 32 33
34
35
36
39 40 4142 433837
1. (CD) Disc Tray
2. (CD) Disc Skip Button
3. (TUNER) Programme Type/Traffic Information
Search Button
4. (TUNER) EON Button
5. (TUNER) ASPM Button
6. (TUNER) Display Mode Selector Button
7. (TUNER) Station Selector Button
8. Timer Set Indicator
9. On/Stand-by Button
10. Timer/Sleep Button
11. Clock Button
12. Function Selector Buttons
13. Equalizer Mode Selector/Extra Bass/Demo Mode
Button
14. Volume Up/Down Buttons
15. (CD) Open/Close Button
16. Headphone Socket
17. Memory/Set Button
18. (CD) Track Down/Review Button
(TUNER) Preset Down Button
(TAPE 2) Rewind Button
19. (CD/TAPE) Stop Button
20. (CD) Play/Repeat Button
(TAPE) Play Button
21. (CD) Track Up/Cue Button
(TUNER) Preset Up Button
(TAPE 2) Fast Forward Button
22. (TAPE 2) Record Pause Button
23. Tuning and Time Up/Down Buttons
26. (CD) Disc Number Indicators
27. Timer Indicator
28. Record Indicator
29. Sleep Indicator
30. Extra Bass Indicator
31. (CD/TUNER) Memory Indicator
32. FM Stereo Mode Indicator
33. FM Stereo Indicator
34. Traffic Information Indicator
35. Traffic Announcement Indicator
36. Traffic Programme Indicator
37. (CD) Repeat Indicator
38. (CD/TAPE) Play Indicator
39. (CD) Pause Indicator
40. Dynamic PTY Indicator
41. EON Indicator
42. RDS Indicator
43. Programme Type Indicator
24. (TAPE 1) Cassette Compartment
TAPE 2) Cassette Compartment
25.
– 4 –
CD-BA1300H
CD-BA1300H
Remote control
2
3
4
5
6
7
19
20
21
22
1
151413 161718
8
9
10
11
12
23
Rear panel
1
1. AC Power Input Socket
2. Speaker Terminals
3. FM 75 Ohms Aerial Socket
4. AM Loop Aerial Socket
CP-BA1300H
2
3
4
1. Remote Control Transmitter LED
CD control section
2. Disc Number Select Buttons
Memory Button
3.
4. Pause Button
5. Clear Button
6. Track Down/Review Button
7. Track Up/Cue Button
8. Disc Skip Button
9. Play/Repeat Button
10. Stop Button
11. Random Button
Tuner control section
12. Preset Up/Down Buttons
Tape control section
13. (TAPE 1) Play Button
14. (TAPE 2) Record Pause Button
15. (TAPE 1/2) Stop Button
16. (TAPE 2) Play Button
17. (TAPE 2) Rewind Button
18. (TAPE 2) Fast Forward Button
1
2
3
4
1. Tweeter
2. Woofer
3. Bass Reflex Duct
4. Speaker Wire
Common section
19. Equalizer Mode Selector Button
20. Function Selector Buttons
21. On/Stand-by Button
22. Extra Bass Button
23. Volume Up/Down Buttons
– 5 –
CD-BA1300H
SETTING THE CLOCK
In this example, the clock is set for the 24-hour (0:00) sys-
tem.
1
Press the ON/STAND-BY button to enter the stand-
by mode.2Press the CLOCK button.
3
Within 5 seconds, press the MEMORY/SET button.
4
Press the TUNING/TIME ( or ) button to select the
time display mode.
Note that this can only be set when the unit is first
installed or it has been reset.
5
Press the MEMORY/SET button.
6
Press the TUNING/TIME ( or ) button to adjust
the hour.
Press the TUNING/TIME ( or ) button once to
advance the time by 1 hour. Hold it down to adv ance con-
tinuously.
When the 12-hour display is selected, "AM" will change
automatically to "PM".
7
Press the MEMORY/SET button.
8
Press the TUNING/TIME ( or ) button to adjust
the minutes.
Press the TUNING/TIME ( or ) button once to
advance the time by 1 minute. Hold it down to change the
time in 5-minute intervals.
The hour setting will not advance even if minutes
advance from "59" to "00".
9
Press the MEMORY/SET button.
The clock starts operating from "0" second. (Seconds are
not displayed.) And then the clock display will disappear
after a few seconds.
To see the time display:
Press the CLOCK button.
The time display will appear for about 5 seconds.
Note:
The clock display will flash on and off at the push of the
CLOCK button when the AC power supply is restored
after a power failure occurs or after the AC power lead is
disconnected. If this happens, follow the procedure below
to change the clock time.
To change the clock time:
1 Press the CLOCK button.
2 Within 5 seconds, press the MEMORY/SET button.
3 Perform steps 6 - 9 above.
To change the time display mode:
1 Perform steps 1 - 2 in "RESETTING THE MICROCOM-
PUTER".
2 Perform steps 1 - 9 above.
(Main unit operation)
"0:00" The 24-hour display will appear.
(0:00 - 23:59)
"AM 0:00" The 12-hour display will appear.
(AM 0:00 - PM 11:59)
"AM 12:00" The 12-hour display will appear.
(AM 12:00 - PM 11:59)
ON/
STAND-BY
CLOCK
MEMORY/SET
TUNING/TIME
( )
AM 0:000:00 AM 12:00
Notes concerning use:
Replace the batteries if the operating distance is reduced
or if the operation becomes erratic.
Periodically clean the transmitter LED on the remote con-
trol and the sensor on the main unit with a soft cloth.
Exposing the sensor on the main unit to strong light may
interfere with operation. Change the lighting or the direc-
tion of the unit.
Keep the remote control away from moisture, excessive
heat, shock, and vibrations.
15
15
0.2 m - 6 m
(8" - 20')
REMOTE CONTROL
RESETTING THE MICROCOMPUTER
Reset the microcomputer under the following condi-
tions:
To erase all of the stored memory contents (clock and
timer settings, and tuner and CD presets).
If the display is not correct.
If the operation is not correct.
1
Press the ON/STAND-BY button to enter the stand-
by mode.
2
Whilst pressing down the / button and the
EQUALIZER/X-BASS/DEMO button, hold down the
ON/STAND-BY button for at least 1 second.
"CLEAR AL" will appear.
Caution:
The operation explained above will erase all data stored
in memory including clock and timer settings, and tuner
and CD presets.
EQUALIZER
X-BASS/
DEMO
ON/
STAND-BY
OPERATION MANUAL
– 6 –
CD-BA1300H
Check the supplied accessories
AM loop aerial
× 1
FM aerial
× 1
Remote control
× 1
AC power lead
× 1
Putting batteries into the remote control
2 "AA" size batteries
(UM/SUM-3, R6, HP-7 or similar)
1
Remove the battery cover .
2
Insert the batteries.
3
Replace the battery cover.
1
2
[For U.K.]
AC power lead
× 1
[Except for U.K.]
Placing the system
10 cm (4")
10 cm (4")
3
10 cm (4")
10 cm (4")
Left speaker
Black
Connections
4
AC 230 V, 50 Hz
1
Connect the AM and FM aerials.
2
Connect the speaker system.
3
Connect the AC power lead.
Right speaker
AM loop
aerial
FM aerial
1
2
Red
[For U.K.] [Except for U.K.]
– 7 –
CD-BA1300H
7
Listening to a tape
1
Press the ON/STAND-BY button to turn the power on.
4
Press the TAPE (1 2) button to select the TAPE 1
or TAPE 2.
3
Load the cassette into the TAPE 1 or TAPE 2 cassette
compartment.
2
Open the cassette door by pushing the area marked
"PUSH EJECT".
5
Press the button to start playback.
1
Press the ON/STAND-BY button to turn the power on.
2
Press the TUNER (BAND) button to select FM ST, FM
or AM.4Adjust the sound volume using the VOLUME buttons.
6
Adjust the sound volume using the VOLUME buttons.
3
Press the TUNING/TIME ( or ) button to tune in-
to the desired station.
Listening to the radio
6
1
Press the ON/STAND-BY button to turn the power on.
2
Press the CD button.
3
Press the OPEN/CLOSE button to open the disc tray .
4
Place the CD(s) on the disc tray, label side up.
5
When loading a third disc, press the DISC SKIP button
to turn the disc tray, then place the CD in the open pos-
ition.
6
Press the OPEN/CLOSE button to close the disc tray.
Listening to a CD
5
7
Press the button. 8Adjust the sound volume using the VOLUME buttons.
And then, close the cassette door completely until it is locked.
1
2
4
3
TAPE 1 TAPE 2
PUSH
EJECT
PUSH
EJECT
1
5
6
3
2
3
4
2
4
1
2
5
3,6
7
8
5
12 cm (5")
8 cm (3")
Resetting the microcomputer
1
Press the ON/STAND-BY button to enter the stand-by
mode.2Whilst pressing down the button and the
EQUALIZER/X-BASS/DEMO button, hold down the
ON/STAND-BY button for at least 1 second.
"CLEAR AL" will appear.
Caution:
The operation explained above will er ase all data stored
in memory including clock and timer settings, and tuner
and CD presets.
If this product is subjected to strong external interference
(mechanical shock, excessive static electricity, abnormal
supply voltage due to lightning, etc.) or if it is operated in-
correctly, it may malfunction or the display may not func-
tion correctly. If such a problem occurs, do the following:
CD pickup cleaning
1
Press the ON/STAND-BY button to turn the power on.
3
Press the CD button and load the desired disc.
2
Load a cassette into the TAPE 2 cassette compartment.
4
Press the REC PAUSE button.
5
Press the button.
Recording from CDs
8
Clean the dust or stain on the CD pickup lens
using a commercial cleaning disc (brush type).
Cleaning disc
TAPE 2
PUSH
EJECT
1
5
4
2
3
1,2
2
2
– 8 –
DISASSEMBLY
CP-BA1300H
STEP REMOVAL
1 Woofer 1. Front Panel .............(A1) x1 9-1
2. Screw......................(A2) x4 9-2
2 Tweeter 1. Screw......................(B1) x2 9-2
PROCEDURE
(A1)x1
CD-BA1300H
FIGURE
Tweeter
(B1)x2
ø3x10mm
Screwdriver
Driver should be
pried away from
Speaker Box.
(A2)x4
ø4x12mm
Woofer
Figure 9-1 Figure 9-2
– 9 –
CD-BA1300H
NOTES ON SCHEMATIC DIAGRAM
• Resistor:
To differentiate the units of resistors, such symbol as K and
M are used: the symbol K means 1000 ohm and the symbol
M means 1000 kohm and the resistor without any symbol is
ohm-type resistor. Besides, the one with “Fusible” is a fuse
type.
• Capacitor:
To indicate the unit of capacitor, a symbol P is used: this
symbol P means micro-micro-farad and the unit of the
capacitor without such a symbol is microfarad. As to
electrolytic capacitor, the expression “capacitance/withstand
voltage” is used.
(CH), (TH), (RH), (UJ): Temperature compensation
(ML): Mylar type
(P.P.): Polypropylene type
• Schematic diagram and Wiring Side of P.W.Board for this
model are subject to change for improvement without prior
notice.
• The indicated voltage in each section is the one measured
by Digital Multimeter between such a section and the chassis with no signal given.
1. In the tuner section,
( ) indicates AM
< > indicates FM stereo
2. In the main section, a tape is being played back.
3. In the deck section, a tape is being played back.
( ) indicates the record state.
4. In the power section, a tape is being played back.
5. In the CD section, the CD is stopped.
• Parts marked with “ ” ( ) are important for
maintaining the safety of the set. Be sure to replace these
parts with specified ones for maintaining the safety and
performance of the set.
REF. NO DESCRIPTION POSITION POSITION
SW1 OPEN/CLOSE ON—OFF
SW2 CLAMP ON—OFF
SW3 DISC NUMBER ON—OFF
SW4 PICKUP IN ON—OFF
SW701 ON/STAND-BY ON—OFF
SW702 CLOCK ON—OFF
SW703 TIMER/SLEEP ON— OFF
SW704 PTY. TI SEARCH ON—OFF
SW705 EON ON—OFF
SW706 ASPM ON—OFF
SW707 DISPLAY MODE ON—OFF
SW708 STATION ON—OFF
SW709 DISC SKIP ON—OFF
SW710 OPEN/CLOSE ON—OFF
REF. NO DESCRIPTION
SW711 EQUALIZER/X-BASS/DEMO ON—OFF
SW712 VOLUME UP ON—OFF
SW713 VOLUME DOWN ON—OFF
SW714 CD ON—OFF
SW715 TAPE ON—OFF
SW716 TUNING/TIME DOWN ON—OFF
SW717 MEMORY/SET ON—OFF
SW718 REWIND ON—OFF
SW719 FAST FORWARD ON—OFF
SW720 PLAY/REPEAT ON—OFF
SW721 STOP ON—OFF
SW723 REC/PAUSE ON—OFF
SW724 TUNING/TIME UP ON—OFF
SW725 TUNER (BAND) ON—OFF
FRONT
VIEW
FRONT
FRONT
VIEW
VIEW
E C B
(S) (G) (D)
(1) (2) (3)
2SC1845 F
2SC380 O
KTA1266 GR
KTA1268 GR
KTA1271 Y
KTA1273 Y
BCE
KTC3199 GR
KTC3200 GR
KTC3203 Y
KRC102 M
KRC104 M
KRC107 M
Figure 10 TYPES OF TRANSISTOR AND LED
KTC2026
– 10 –
4204SRT7
TO MAIN SECTION
(TO IC601)
TO DISPLAY SECTION
SW1
OPEN/
CLOSE
12
CD-BA1300H
SW2
SW3
CLAMP
DISC
NUMBER
M
+
6
5
3
4
M3
T/T
UP/DOWN
MOTOR
-
BI4
X1
16.9344MHz
1
R-CH
2
AGND
12
L-CH
DGND
+5V(+B4)
5
3
4
CNP11
CDINT
217
WRQ
DRF
CE
DO
DI
5
6
43
CLK
CLAMP SW
CD RES
89
GND
10
CNP12
12
56
3
4
3
4
56
CNS4
CNP4
Q2
CONT4
RFENV
FE
30
CONT3
CONT5
TE
CONT2
SLDO
SPDO
FDO
TDO
74
64
40
19
13
3
33
26
25
24
23
75
76
65
CE
CL
66
DI
67
DO
68
INT
69
WRQ
70
RES
71
72
DEF
XOUT
52
XIN
51
VDD5V
73
CONT7
CONT6
VVDD
ADAVDD
VDD
5
183644 49 50 7 14 15 16
47 48 32 31
45 46
LVSS
RVSS
LCHO
IC2
LC78641E
SERVO/SIGNAL
CONTROL
LVDD
RVDD
XVDD
RCHO
HFL
CONSTANT
VOLTAGR
+3.3V
PICKUP UNIT
+5V
+3.3V
1
2 1725 4142 3839
FD
TO
SLDO
SPDO
22
18 19 20
Q1
VCC
30
23
17
HFL
IC1
LA9235M
SERVO AMP.
11
9
TIN2
TIN1
FIN2
FIN1
12
34
+5V
21
FE
TE
7
FE-
TE-
PD
LDD
RFEV
LASER
DRIVER
Q3
+3.3V
8
M1
SPINDLE
MOTOR
FOCUS COIL
TRACKING COIL
M2
SLED
MOTOR
VCC1
18
VCC4
40
24
VCC2
23
+5V
VCC3
28
FO+
FO-
45671516 26 27
M
M
LD_M-
IC3
M63001FP
FOCUS/TRACKING/
SPIN/SLED DRIVER
TR-
TR+
LD_M+
SL-
SL+
M+
LOADINGM-LOADING
SP-
SP+
35
29
22
21
14
8
SW4
PICKUP IN
Figure 11 BLOCK DIAGRAM (1/3)
– 11 –
CD-BA1300H
Q
FM
ANTENNA
TERMINAL
TAPE
MOTOR
SOLENOID
T2 PLAY
T1 PLAY
R.PLAY
F.PLAY
TAPE 1
P.B. HEAD
TAPE 2
REC/P.B.
HEAD
AM LOOP
ANTANNA
L341
BALUN
T303
MOTOR
DRIVER
Q706
M
Q704
Q705
IC701
54PIN
IC701
53PIN
IC701
56PIN
IC701
55PIN
FROM CD SECTION
CNP11
L-CH
R-CH
REC
P.B.
L-CH
R-CH
Q104~
Q107
AC BIAS
ERASE
HEAD
8
2
AM TRACKING
+B2
+B2
CNS601
1
2
3
4
5
SWITCHING
Q108
Q109
SWITCHING
FE301
TA7358AP
FM FRONT END
4
3
7
6
FMOSC
AM BAND
T306
COVERAGE
CE
MPX
2 4 3
IC101
AN7345K
PLAYBACK AND
RECORD/PLAYBACK AMP.
L(T1)
1
R(T1)
24
L(T2)
2
R(T2)
23
LNF
3
RNF
22
POP
REDUCE
LREC
RREC
REF
T1/T2
6
9
REC
16
14
NOR/
12
15
SWITCHING
12
Q103
Q101
Q114
L104
BIAS
OSC
SWITCHING
1
5
FM +B
2021222324
DI
CL
DO
IN
RDS DECORDER
VDDA
VSSA
P.B
H/N
T1/T2HIGH
19
Q102
FM IF
CF301
SWITCHING
Q360
+B3
ICT21
LC72722
7 8
13
L
4
R
21
5
20
7
18
LNF
8
RNF
17
ALC
10
Q112
SWITCHING
+B3
PB
RECRL
FM IF
AMP.
Q301
VT
FM
7
Q113
BIAS
20
VSSD
CF302
13121415
VDDD
+B3
XIN
XOUT
T351
AM IF
2
1
AM
MIX
IC303
LA1832S
FM IF DET./FM MPX./AM IF
23
FMAFC
AMRFIN
AMOSCIN
X352
4.5MHZ
15
22
1
CE
OSC
3
XT21
4.5MHz
16
IC302
LC72131
PLL(TUNER)
4 5 6
DI
CL
DO
QT22
TAPE
TUNER
L
R
L
R
L
CD
R
CF352
4
5
AM IF
GND
FM/AM
OUT
7
STEREO
11
18
QT21
FM/AM
L354
LOW
PASS
FILTER
AMP.
9
2
1
242122
21
10
15
11
14
12
LC75341
AUDIOPROCESSOR
13
17
8
7
CF351
9
FMFM+B
DET
16
10
MO/ST
IC601
18
+B3
X351
456kHz
13
8
17
MO/ST
VCO
L
14
R
15
FM/AMMPXIN
12
17
R
21
4
3
23
Q601
Q602
L
SYSTEM
MUTE
+B3
Q110
Q111
MUTING
REC/PLAY
T1/T2
BAIS
Figure 12 BLOCK DIAGRAM (2/3)
– 12 –
CD-BA1300H
+B3
Q701
1
SP.DET.
FL701
DISPLAY
2
10 111315 16 19 20 22 261417 182127
3
5556
575859
71
78
VLOAD
79
80
91
92
MICROCOMPUTER
99
100
VDD
145
9
6
10
7
+B6
Q901
Q902
RESET
Q707
IC701
IX0337AW
SYSTEM
RESET
11
12 13 15 16
XL701
4.1943 MHz
+B6
30
+B6
VDD
VDD
17
RESET IC
IC704
3
KIA7042PA
31
CEDICL
20
21222324
2
32 33
SYS.STOP
AVDD
1
404142434445464748495051525354
39
38
37
36
35
+B6
34
33
31
DO
+B6
KEY
SW701-SW721
SW723-SW725
TO CD
SECTION
JK901
HEADPHONES
SO901
SPEAKER
IC901
L
1
STK402-020
POWER
R
Q601
Q602
L
SYSTEM
MUTE
R
15
Vcc
8
AMP.
13
Q804
R-OUT
10
L-OUT
7
PT801
MAIN POWER
TRANSFORMER
F802
T3.15A L 250V
D814
TERMINAL
RL801
+B1
REC/PLAY
T1/T2
BAIS
VF1
VF2
+B2
+B3
+B4
M10V
A10V
+5V
SW
+B5
+B6
UNSWITCH
Q805
IC801
KIA7810AP
VOLTAGE
REGULATOR
IC802
KIA7805P
VOLTAGE
REGULATOR
+5V
5V
D810 D813
D806
AN78L05
CONSTANT
VOLTAGE REGULATOR
IC803
F803
T3.15A L 250V
F801
T2A L 250V
Q803
D802~805
T.F.
PT802
SUB POWER
TRANSFORMER
AC INPUT
L801
LINE
FILTER
SO902
AC POWER
SUPPLY CORD
AC 230V,50Hz
Figure 13 BLOCK DIAGRAM (3/3)
– 13 –
CD-BA1300H
A
D
R
P
S
2
3
0
8
0
2
0
7
A
CNS1B
Vcc
7
7
Vref
6
B
6
E
5
5
A
4
4
B
3
3
F
2
2
C
1
1
C
D
CD SERVO PWB-B
CNS1A
7
7
6
6
R51 68K
5
5
R52 68K
4
4
R53 68K
3
3
R54 68K
2
2
1
1
CNP1
R56
68K
+B
C53
0.001
Q3
KTA1266GR
LASER DRIVER
C51
47/10
C41
100/6.3
C23
0.047
C24
2.2/50
C22
100P
R15
10K
8
R12
680
R79
R1
1.5M
68
C
C21
0.1
0.
R11
12K
R1
R80
1M
1.
C27
0.1
C26
0.047
PH(
A
C
C28
0.
47/10
2
R44
1K
EFBL
+B
R50
47
TIN1
FIN1
FIN2
TIN2
R55
68K
FIN1
1
REF
FIN2
2
REF
TIN1
C55
C54
0.01
47/10
C7
10/16
C8
0.022
+B
R25
10K
R47
3.3
TIN2
C6
100/6.3
REF1
VREF
LDD
GND
LDON
AGON
EFBL
TEST0
TES1
3
REF
4
REF
5
6
7
8
9
10
11
12
13
14
15
REF
APC
ODRV
AGCON
IC1
LA9235M
SERVO AMP.
REF
REF
LPF
REF
ODRV
REF
REF
REF
AGCON
PH/BH
C11
47/6.3
VCC
30
ODRV
REF
PH
DH
REF
LPF
REF
LPF
REF
C12
0.022
RFSW
29
R42
120K
RF-
28
RF
27
NC
26
PH
25
BH
24
23
RFEV
22
FE-
21
FE
20
TE-
19
TE
18
HFL
17
16
TEST
C18
R7
3P
6.8K
(CH)
R6
R5
27K
39K
5
C13
0.01
C14
0.33
R3
47K
R4
10K
4
C17
0.0047
C20
0.1
C82
0.022
C25
0.022
R10
27K
R8
330
C42
68P
(CH)
E
TR+
FO+
FOTR-
F
ACTUATOR
PICKUP UNIT
G
CD MOTOR PWB-C
M1
SPINDLE
MOTOR
M2
SLED
MOTOR
SW4
PICKUP IN
H
13
TDO
LD_M+
LD_MVCC4
LOADING M+
LOADING M-
GND
VCC3
SPSP+
SPDO
SPO
VCC2(SPN)
C47
100/6.3
+B
+B
C52
0.01
+B
TDO
TRTR+
FO+
FOGND
+
M
+
M
-
PD
VR
LD
CNP3A
1
1
2
2
3
3
4
4
5
5
6
6
7
7
CNS2B
CNS3B
6
6
5
5
4
4
3
3
2
1
1
1
2
3
4
5
6
7
88
6
5
4
3
22
1
CNS2A
CNS3A
TR-
1
TR+
2
FO+
3
FO-
4
GND
5
PD
6
VR
7
LD
88
CNP2
R96
+B
1.5K
R48
6.8K
100/6.3
SP-
6
SP+
5
SL+
4
SL-
3
PUIN
2
GND(D)
1
CNP3
+B
TO
FDO
FD
FO
C46
0.022
FO+
FO-
TR+
TR-
GND
SL-
SL+
SLDO
VCC1
STANDBY
Vref
MUTE
C50
C49
100/6.3
-
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
-
+
+
-
+
-
+
IC3
M63001FP
FOCUS/TRACKING/
-
-
+
+
+
-
SPIN/SLED DRIVER
+B
+
42
-
+
-
41
+
40
-
39
38
37
36
35
34
33
32
31
30
29
28
27
26
-
-
25
+
+
+
24
-
+
23
-
+
-
22
FDO
• NOTES ON SCHEMATIC DIAGRAM can be found on page 10.
1
23456
Figure 14 SCHEMATIC DIAGRAM (1/10)
– 14 –
Loading...