SHARP AR208D-S, AR-208D Service Manual

(AR-208S/AR-208D)

SERVICE MANUAL

CODE : 00ZAR208D/A1E

DIGITAL MULTIFUNCTIONAL SYSTEM

AR-208S

MODEL AR-208D

CONTENTS

[1] GENERAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 - 1

[2] SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 - 1

[3] CONSUMABLE PARTS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 - 1

[4] EXTERNAL VIEWS AND INTERNAL STRUCTURES . . . . . . . . . 4 - 1

[5] UNPACKING AND INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . 5 - 1

[6] COPY PROCESS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 - 1

[7] OPERATIONAL DESCRIPTIONS . . . . . . . . . . . . . . . . . . . . . . . . . 7 - 1

[8] DISASSEMBLY AND ASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . 8 - 1

[9] ADJUSTMENTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 - 1

[10] TEST COMMAND, TROUBLE CODES . . . . . . . . . . . . . . . . . . . . 10 - 1

[11] MAINTENANCE. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 - 1

[12] USER PROGRAM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 - 1

[13] ELECTRICAL SECTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 - 1

[14] CIRCUIT DIAGRAM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 - 1

[15] FIRMWARE DOWNLOAD PROCEDURES. . . . . . . . . . . . . . . . . 15 - 1

Parts marked with “ ” are important for maintaining the safety of the set. Be sure to replace these parts with specified ones for maintaining the safety and performance of the set.

This document has been published to be used

SHARP CORPORATION

for after sales service only. The contents are subject to change without notice.

CAUTION

This product is a class 1 laser product that complies with 21CFR 1040 of the CDRH standard and IEC825. This means that this machine does not produce hazardous laser radiation. The use of controls, adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure.

This laser radiation is not a danger to the skin, but when an exact focusing of the laser beam is achieved on the eye’s retina, there is the danger of spot damage to the retina.

The following cautions must be observed to avoid exposure of the laser beam to your eyes at the time of servicing.

1) When a problem in the laser optical unit has occurred, the whole optical unit must be exchanged as a unit, not as individual parts.

2) Do not look into the machine with the main switch turned on after removing the developer unit, toner cartridge, and drum cartridge.

3) Do not look into the laser beam exposure slit of the laser optical unit with the connector connected when removing and installing the optical system.

4) The middle frame contains the safety interlock switch.

Do not defeat the safety interlock by inserting wedges or other items into the switch slot.

LASER WAVE – LENGTH : 770 – 795nm Pulse times : 10.24µsec Out put power : 0.15mW

± 0.01mW

CAUTION

INVISIBLE LASER RADIATION,

WHEN OPEN AND INTERLOCKS DEFEATED.

AVOID EXPOSURE TO BEAM.

VORSICHT

UNSICHTBARE LASERSTRAHLUNG, WENN ABDECKUNG GEÖFFNET UND SICHERHEITSVERRIEGELUNG ÜBERBRÜCKT. NICHT DEM STRAHL AUSSETZEN.

VARO !

AVATTAESSA JA SUOJALUKITUS OHITETTAESSA OLET ALTTIINA NÄKYMÄTTÖMÄLLE LASERSÄTEILYLLE ÄLÄ KATSO SÄTEESEEN.

ADVARSEL

USYNLIG LASERSTRÅLNING VED ÅBNING, NÅR SIKKERHEDSBRYDERE ER UDE AF FUNKTION. UNDGÅ UDSAETTELSE FOR STRÅLNING.

VARNING !

OSYNLIG LASERSTRÅLNING NÄR DENNA DEL ÄR ÖPPNAD OCH SPÄRREN ÄR URKOPPLAD. BETRAKTA EJ STRÅLEN. – STRÅLEN ÄR FARLIG.

At the production line, the output power of the scanner unit is adjusted to 0.57 MILLI-WATT PLUS 20 PCTS and is maintained constant by the operation of the Automatic Power Control (APC). Even if the APC circuit fails in operation for some reason, the maximum output power will only be 15 MILLI-WATT 0.1 MICRO-SEC. Giving and accessible emission level of 42 MICRO-WATT which is still-less than the limit of CLASS-1 laser product.

Caution

This product contains a low power laser device. To ensure continued safety do not remove any cover or attempt to gain access to the inside of the product. Refer all servicing to qualified personnel.

The foregoing is applicable only to the 220V model, 230V model and 240V model.

VAROITUS! LAITTEEN KÄYTTÄMINEN MUULLA KUIN TÄSSÄ KÄYTTÖOHJEESSA MAINITULLA TAVALLA SAATTAA ALTISTAA KÄYTTÄJÄN TURVALLISUUSLUOKAN 1 YLITTÄVÄLLE NÄKYMÄTTÖMÄLLE LASERSÄTEILYLLE.

VARNING - OM APPARATEN ANVÄNDS PÅ ANNAT SÄTT ÄN I DENNA BRUKSANVISNING SPECIFICERATS, KAN ANVÄNDAREN UTSÄTTAS FÖR OSYNLIG LASERSTRÅLNING, SOM ÖVERSKRIDER GRÄNSEN FÖR LASERKLASS 1.

LUOKAN 1 LASERLAITE KLASS 1 LASER APPARAT

CONTENTS

[1] GENERAL

1. Major functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1

2. Note for servicing and handling. . . . . . . . . . . . . . . . . . . . . . . . . . 1-1

[2] SPECIFICATIONS

1. Basic specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1

2. Operation specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1

3. Copy performance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2

4. SPLC printer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3

5. Scan function. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3

6. RSPF. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3

[3] CONSUMABLE PARTS

1. Supply list . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1

A. SEC/SECL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1

2. Environmental . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1

3. Production control number (lot No.) identification . . . . . . . . . . . . 3-1

4. Toner cartridge replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-2

[4] EXTERNAL VIEWS AND INTERNAL STRUCTURES

1. Appearance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1

2. Internal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1

3. Operation panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-2

4. Motors, solenoids and clutch. . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-3

5. Sensors and switches . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-4

6. PWB unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-5

7. Cross sectional view . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-6

[5] UNPACKING AND INSTALLATION

1. Copier installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-1

2. Cautions on handling. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-1

3. Checking packed components and accessories . . . . . . . . . . . . . 5-1

4. Unpacking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-2

5. Removing protective packing materials. . . . . . . . . . . . . . . . . . . . 5-2

6. Developer unit installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-2

7. Toner cartridge installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-3

8. Loading the paper tray . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-4

9. Power to copier . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-4

10. Software . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-5

A. Before installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-5

B. Installing the software . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-5

C. Setting up Button Manager . . . . . . . . . . . . . . . . . . . . . . . . . . 5-8

11. Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-9

A. USB . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-9

12. Moving . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-9

13. Scanner moisture-proof kit . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-10

A. Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-10

B. Precautions at installation . . . . . . . . . . . . . . . . . . . . . . . . . . 5-10

C. Attachment method . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-10

[6] COPY PROCESS

1. Functional diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-1

2. Outline of print process . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-2

3. Actual print process . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-2

[7] OPERATIONAL DESCRIPTIONS

1. Outline of operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-1

2. Scanner section. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-2

A. Scanner unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-2

B. Optical system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-2

C. Drive system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-2

3. Laser unit. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-3

A. Basic structure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-3

B. Laser beam path . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-3

C. Composition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-3

4. Fuser section. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-3

A. General description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-4

5. Paper feed section and paper transport section . . . . . . . . . . . . . 7-4

A. Paper transport path and general operations. . . . . . . . . . . . . 7-4

6. RSPF section . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-7

A. Outline . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-7

B. Document transport path and basic composition . . . . . . . . . . 7-7

C. Operational descriptions . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-7

D. Cases where a document jam is caused . . . . . . . . . . . . . . . . 7-8

E. RSPF open/close detection (book document detection) . . . . 7-8

7. D-D (Duplex to Duplex) mode paper/document transport

(Duplex model) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-8

A. Initial state . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-8

B. Front copy . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-8

C. Back copy . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-8

8. Shifter. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-9

[8] DISASSEMBLY AND ASSEMBLY

1. High voltage section . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-1

A. List. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-1

B. Drum replacement. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-1

C. Disassembly procedure (Transfer charger unit) . . . . . . . . . . . 8-3

D. Assembly procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-3

E. TC unit cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-3

F. Charger wire replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-4

2. Operation panel section . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-4

A. List. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-4

B. Disassembly procedure. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-4

C. Assembly procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-5

3. Optical section . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-5

A. List. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-5

B. Disassembly procedure. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-5

C. Assembly procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-7

4. Fusing section . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-7

A. List. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-7

B. Disassembly procedure. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-7

C. Assembly procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-10

5. Tray paper feed/transport section . . . . . . . . . . . . . . . . . . . . . . . 8-10

A. List. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-10

B. Disassembly procedure. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-10

C. Assembly procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-15

6. Manual paper feed section. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-16

A. List. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-16

B. Disassembly procedure. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-16

C. Assembly procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-17

D. Pressure plate holder attachment . . . . . . . . . . . . . . . . . . . . . 8-17

7. Rear frame section . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-18

A. List. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-18

B. Disassembly procedure. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-18

C. Assembly procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-18

8. Power section. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-19

A. List. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-19

B. Disassembly procedure. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-19

C. Assembly procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-19

9. DV unit section . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-19

A. Developer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-19

B. DV seal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-19

C. DV blade . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-20

D. DV doctor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-20

E. DV sensor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-20

10. Duplex motor section (AR-208D only) . . . . . . . . . . . . . . . . . . . . 8-20

A. List. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-20

B. Disassembly procedure. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-20

C. Assembly procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-20

11. Reverse roller section (AR-208D only) . . . . . . . . . . . . . . . . . . . 8-21

A. List. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-21

B. Disassembly procedure. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-21

C. Assembly procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-21

12. RSPF section . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-21

A. Front cabinet, rear cabinet . . . . . . . . . . . . . . . . . . . . . . . . . . 8-21

B. Upper door unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-21

C. Document tray unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-22

D. Upper door open/close sensor . . . . . . . . . . . . . . . . . . . . . . . 8-22

E. Reverse clutch, paper exit roller . . . . . . . . . . . . . . . . . . . . . . 8-22

F. Drive unit. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-22

G. Shutter solenoid . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-23

H. Pickup roller, take-up roller . . . . . . . . . . . . . . . . . . . . . . . . . . 8-24

I. Paper empty sensor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-24

J. PS roller . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-25

K. Upper transport roller . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-25

L. Paper sensor. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-26

M. Lower transport roller . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-26

N. Paper exit sensor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-26

[9] ADJUSTMENTS

1. Optical section. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-1

A. Copy magnification ratio adjustment . . . . . . . . . . . . . . . . . . . 9-1

2. Copy density adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-3

A. Copy density adjustment timing . . . . . . . . . . . . . . . . . . . . . . . 9-3

B. Note for copy density adjustment. . . . . . . . . . . . . . . . . . . . . . 9-3

C. Necessary tool for copy density adjustment. . . . . . . . . . . . . . 9-4

D. Features of copy density adjustment . . . . . . . . . . . . . . . . . . . 9-4

E. Copy density adjustment procedure. . . . . . . . . . . . . . . . . . . . 9-4

3. High voltage adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-5

A. Main charger (Grid bias) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-5

B. DV bias check . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-5

4. Duplex adjustment. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-5

A. Adjusting the paper reverse position in memory

for duplex copying . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-5

B. Adjusting trailing edge void in duplex copy mode . . . . . . . . . 9-6

5. RSPF scan position automatic adjustment . . . . . . . . . . . . . . . . . 9-7

6. RSPF mode sub scanning direction magnification ratio

adjustment. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-7

7. Automatic black level correction . . . . . . . . . . . . . . . . . . . . . . . . . 9-8

[10] TEST COMMAND, TROUBLE CODES

1. Entering the test command mode . . . . . . . . . . . . . . . . . . . . . . . 10-1

2. Key rule . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-1

3. List of test commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-1

4. Descriptions of various test commands. . . . . . . . . . . . . . . . . . . 10-3

5. Trouble codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-39

A. Trouble codes list . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-39

B. Details of trouble codes . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-39

[11] MAINTENANCE

1. Maintenance table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-1

2. Maintenance display system . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-1

3. Remaining toner indication . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-1

[12] USER PROGRAM

1. User programs. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12-1

A. Copy mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12-1

B. Print mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12-2

2. Selecting a setting for a user program . . . . . . . . . . . . . . . . . . . 12-3

[13] ELECTRICAL SECTION

1. Block diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13-1

A. Overall block diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13-1

2. Signal name list . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13-2

[14] CIRCUIT DIAGRAM

1. MCU PWB . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14-1

2. OPERATION PWB . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14-17

3. ACTUAL WIRING DIAGRAM . . . . . . . . . . . . . . . . . . . . . . . . . 14-20

[15] FIRMWARE DOWNLOAD PROCEDURES

1. Initial setting (Serial number setting procedures) . . . . . . . . . . . 15-1

2. Download procedures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15-1

3. Version acquisition procedures . . . . . . . . . . . . . . . . . . . . . . . . . 15-3

4. EEPROM data acquisition procedure . . . . . . . . . . . . . . . . . . . . 15-4

5. Installing procedures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15-5

[1] GENERAL

1. Major functions

Configurations

Item

CPM

SB/

Model

AR-208S 20 MB Opt

AR-208D 20 MB Opt

(Letter)

2 Tray SPF R-SPF

(250)

✕❍ ❍ ✕ ❍ ❍ ✕ ❍Opt ❍✕ ❍

✕ ❍ ❍ ✕ ❍ ❍ ❍ ❍ Opt ❍ ✕ ❍

Descriptions of items

CPM: Copy speed (Copies Per Minute) SB/MB: SB = Manual feed single bypass,

MB = Manual feed multi bypass 2 tray: Second cassette unit SPF: Original feed unit R-SPF: Duplex original feed unit Color scanner: Color scanner function GDI printer: GDI printer function with USB

SPLC: SPLC printer function E-SORT: Electrical sort

Duplex: Auto duplex copy function Shifter: Job separator function FAX: FAX function Sharpdesk: Scanner utilities IEEE1284: Interface port (parallel) USB: Interface port (USB) RJ45: Interface port (Network) External NIC: AR-NB2A

Descriptions of table

❍: Standard provision ✕: No function or no option available

Opt: Option

Scanner

(push)

Color

GDI

SPLC E-SORT Duplex Shifter FAX

printer

(Options)

Sharp

IEEE 1284

USB RJ45

(2.0Hi)

desk

(AR-208S/AR-208D)

AR-D33 AR-NB2A

External

NIC

✕ Opt

AR-FX13

2. Note for servicing and handling

When the main unit power is repeatedly turned OFF/ON rapidly (for about 1sec), the IC (OA982) on the MCU PWB may malfunction to cause an error (E1-00 Communication error), which does not boot the machine. In case of this error, the blank display is kept for several tens seconds and then "E100" is displayed on the panel display.

Turn off the power and keep it for more than 10sec. Then turn on the power. When the machine is booted.: There is no problem in the MCU PWB. When the machine is not booted.: The MCU PWB trouble

AR-208S/208D GENERAL 1 - 1

[2] SPECIFICATIONS

1. Basic specifications

Item Type Desktop Copy system Dry, electrostatic Segment (class) Digital personal copier Copier dimensions AR-208S 20-1/2” (W) x 17-5/8” (D) x 14-5/8” (H) (518mm (W) x 445mm (D) x 371mm (H))

AR-208D 20-1/2” (W) x 17-5/8” (D) x 14-5/8” (H) (518mm (W) x 445mm (D) x 371mm (H))

Weight (Approximately) AR-208S 43.9lbs.(19.9kg) DV unit is not included.

AR-208D 45.4lbs.(20.6kg)

2. Operation specifications

Section, item Details

Paper feed section

Paper exit section Exit way Face down

Originals Original set Center Registration (left edge)

Optical section

Image forming Photoconductor Type OPC (30ø)

Paper feed system 1 tray (250 sheets) + multi-bypass (50 sheets) Inch

system

AB system Tray paper feed section Paper size A4, B5, A5 (Landscape)

Scanning section

Writing section

Tray paper feed section Paper size 8-1/2" x 14", 8-1/2" x 13", 8-1/2" x 11", 8-1/2" x 5-1/2"

Paper weight 15 - 21 lbs. Paper feed capacity 250 sheets Kinds Standard paper, specified paper, recycled paper

Remark User adjustment of paper guide available Multi-bypass paper feed section

Multi-bypass paper feed section

Capacity of output tray 200 sheets

Max. original size A4 (8-1/2" x 14") Original kinds sheet, book Original size detection None Scanning system 3 CCDs (RGB) sensor scanning by lighting white lamp CCD sensor Resolution 600 dpi Lighting lamp Type CCFL

Output data Output: R, G, B 1 or 8 bits/pixel /

Writing system Writing to OPC drum by the semiconductor laser Laser unit Resolution 600 dpi

Charger Charging system Saw-tooth charging with a grid, / (-) scorotron discharge

Developing Developing system Dry, 2-component magnetic brush development system Cleaning Cleaning system Counter blade system (Counter to rotation)

Paper size Max, feedable size: 8-1/2" x 14" /

Paper weight 15 - 34.5 lbs.

Paper feed capacity 50 sheets

Kinds Standard paper, specified paper, recycled paper, OHP,

Remark User adjustment of paper guide available

Paper weight 56 - 80g/m

Paper feed capacity 250 sheets

Kinds Standard paper, specified paper, recycled paper

Remark User adjustment of paper guide available

Paper size Max, feedable size: A4 / Min, feedable size: 89 x 140mm

Paper weight 56 - 128g/m

Paper feed capacity 50 sheets

Kinds Standard paper, specified paper, recycled paper, OHP,

Remark User adjustment of paper guide available

Voltage 560Vrms

Power consumption 2.8W

Life 25K

Transfer system (+) DC corotron system

Separation system (-) DC corotron system

(Landscape)

Min, feedable size: 3.87" x 5.83"

Label, Envelop (Single copy)

Input: A/D 16 bits (12 bits actual)

AR-208S/208D SPECIFICATIONS 2 - 1

Section, item Details

Fusing section Fusing system Heat roller system

Upper heat roller Type Teflon roller Lower heat roller Type Silicon rubber roller Heater lamp Type Halogen lamp

Voltage 120V

Power consumption 800W

Electrical section Power source Voltage 120V

Frequency Common use for 50 and 60Hz Power consumption Max. Less than 1000W

Average (during copying) 380Wh/H

Average (stand-by) 80Wh/H

Pre-heat mode 28Wh/H

Auto power shut-off mode 12.5W or less

3. Copy performance

Section, item Details

Copy magnification Fixed magnification

Manual steps (manual, photo) 5 steps Copy speed (CPM) First-copy time *1

Max. continuous copy quantity 99 Void Void area Leading edge 1 - 4mm

Warm-up time 0 sec. Immediately the ready lamp is lit. Power save mode reset time 0 sec. Immediately the ready lamp is lit. Paper jam recovery time 0 sec.

*1: The first-copy time is measured after the power save indicator turns off following power on, using the document glass with the polygon rotat-

ing in the copy ready state and "Selection of copy start state" set to ON in the user programs (8-1/2" x 11" (A4), paper fed from paper tray). The first-copy time may vary depending on machine operating conditions and ambient conditions such as temperature.

ratios

Zooming magnification ratios

(Approximately)

Inch system 8-1/2" x 11" (Landscape)

AB system A4 (Landscape)

AB system B5 (Landscape)

Image loss Leading edge same size: 3.0mm or less (OC) / 4mm or less (RSPF)

Same size 20

Trailing edge 4mm or less Side edge void area 0.5mm or more (per side)

4 Reduction + 3 Enlargement (Inch system: 25, 50, 64, 78, 100, 129, 200, 400%) (AB system: 25, 50, 70, 86, 100, 141, 200, 400%) 25 - 400% (376 steps in 1% increments) 50 - 200% when using RSPF (151 steps in 1% increments)

8.0 seconds (When user program 24 is set to OFF)

10.7 seconds (When user program 24 is set to ON) (paper: A4 (8-1/2" x 11"), exposure mode: AUTO, copy ratio: 100

4.5mm or less (total of both sides)

Enlarge: 1.5mm or less (OC) / 3mm or less (RSPF) Reduction (50%): 6.0mm or less (OC) / 8mm or less (RSPF)

∗ Jam recovery condition: Recovery time from 60 sec of door open.

AR-208S/208D SPECIFICATIONS 2 - 2

4. SPLC printer

Print speed Max. 20ppm (Paper size: A4, excluding manual paper feed)

* Varies depending on the PC performance.

First print time 8 sec. (without data transfer time) Duplex Yes (AR-208D only) ROPM Yes CPU None Memory 64MB Interface USB2.0 (Hi Speed) Network Option: Network expansion kit the AR-NB2A Emulation SPLC (JBIG GDI) MIB support No Resolution 600dpi *1 Supported OS Windows 98/Me, Windows 2000 Professional, Windows XP Home Edition/Professional, Windows Vista WHQL support Yes *2 Application Status window

*1: Engine Resolution *2: Running change

5. Scan function

Type Flat Bed Color Scanner Scanning system Document glass / RSPF Light source 3 CCDs (RGB) sensor scanning by lighting white lamp (1 pcs of CCFL) Resolution Optical: 600 x 1200dpi Setting range: 50 - 9600dpi

Originals Sheet type / Book type Output data R, G, B 1 or 8 bits/pixel / A/D 16bit Scan range OC / RSPF: 8.5" (297mm) (L) x 14" (431mm) (W)

Scan speed OC / RSPF: Max. 2.88ms/line(Color/Gray scale) Protocol TWAIN / WIA (Only XP Vista) / STI Support file format RAW / JPEG Interface USB2.0 (Hi Speed data transmission) Scanner utility Button Manager / Sharpdesk / Composer Scan key/lamp Yes Duplex scan Yes (AR-208D only) Supported OS Windows 98/Me, 2000 Professional, XP Home Edition / Professional, Vista Void area No WHQL supported Yes *1

*1: Running change

(Preview resolution is fixed at 75dpi)

Original position: Platen: Left center / RSPF: Right center

6. RSPF

Original capacity 50 sheets (56 - 90g/m Original size A4, B5, A5 / 8-1/2" x 14", 8-1/2" x 11", 8-1/2" x 5-1/2" Original replacement speed 8-1/2" x 11" about 14 sheets (70%)

A4 about 13 sheets (65%)

Job speed (Tray1,Landscape) Single copy S to S About 14CPM (8-1/2" x 11") About 13CPM (A4)

S to D About 10CPM (1 - 30 sheets)(*1) About 5.6CPM (31 sheets ~) D to S About 6CPM D to D About 6CPM (1 - 30 sheets)(*1) About 5.6CPM (31 sheets ~)

Multi copy S to S About 20CPM

S to D About 13CPM (1 - 30 sheets)(*1) About 5.6CPM (31 sheets ~) D to S About 16CPM

D to D About 13CPM (1 - 30 sheets)(*1) About 5.6CPM (31 sheets ~) Original placement Face up Original weight 15 - 23.9lbs. (56 - 90g/m Mixed feeding No Original which cannot Thermal papers, originals with punch holes for files, be used folded paper, transparent

originals such as OHP films, stapled or clip used originals with cover up liquid used, Originals

with tape sealed, originals with high level frictional coefficient such as photos or catalogs.

[Conditions] Speed with tray 1, normal size, paper size of 8.5" x 11" (A4), and RSPF. *1: Indicates the speed from 1st to 30th sheet (i.e., 60th surface).

AR-208S/208D SPECIFICATIONS 2 - 3

) or 6.5mm, 1/4" or less.

)

[3] CONSUMABLE PARTS

1. Supply list

A. SEC/SECL

No. Name Content Life Product name Packing form

1 Toner cartridge

(Black)

2 Developer Developer (Developer: Net Weight 170g)

3 Drum kit Drum

Note: Printing of the master/individual cartons is made in 2 languages, English/French.

Packed together with the machine: DR 25K/Developer UN/Process UN

Toner (Toner: Net Weight 243g) Polyethylene bag

Drum fixing plate

× 10 80K

(8K x 10Pcs)

× 10

× 10 250K

(25K x 10Pcs)

× 1 25K AR-152DR One carton of the × 1

AR-208MT (A4 6% document)

AR-208MD One carton of the

One carton of the AR-208MT includes 10 toner cartridges.

AR-208MD includes 10 developers.

collective package includes 10 units of the AR-152DR.

2. Environmental

The environmental conditions for assuring the copy quality and the machine operations are as follows:

(1) Normal operating condition

Temperature: 20°C to 25°C Humidity: 65

(2) Acceptable operating condition

(3) Transportation condition

± 5%RH

Humidity (RH)

85%

60%

20%

10˚C 30˚C 35˚C

Humidity (RH)

90%

60%

(4) Supply storage condition

Humidity (RH)

90%

20%

–5˚C 45˚C

3. Production control number (lot No.) identification

Production month Production day Destination code ∗ (Dealer, distributor, OEM, etc.) Production place (SOCC: Fixed to B.) End digit of year Version No.

15%

–25˚C 30˚C 40˚C

The label on the drum cartridge shows the date of production. (SOCC production)

Production month Production day Destination code (Dealer, distributor, OEM, etc.) Production place (SOCC: Fixed to B.) End digit of year Version No.

AR-208S/208D CONSUMABLE PARTS 3 - 1

Production control label attachment position

Production control label attachment position(*1)

4) Put Toner unit in a collection bag immediately after removing it

from the copier

Note: Never carry exposed Toner unit. Be sure to put it in the

collection bag.

∗1 The production control label is not attached to the cartridge of a

China product.

Sub lot Production day Production month End digit of year Production place

4. Toner cartridge replacement

1) Open the front and side cabinets of the copier.

2) Keep holding Toner lover, and

3) Carefully pull out Toner unit from the copier.

AR-208S/208D CONSUMABLE PARTS 3 - 2

[4] EXTERNAL VIEWS AND INTERNAL STRUCTURES

1. Appearance

RSPF

Interface

1 2

3 4

5 6

1 Document glass 2 Operation panel 3 Front cover 4 Paper tray 5 Side cover 6 Side cover open button

7 Bypass tray paper guides 8 Bypass tray 9 Original guides 10 Document feeder cover 11 Document feeder tray 12 Exit area 13 Paper output tray 14 Paper output tray extension 15 Power switch 16 Handles 17 Power cord 18 USB connector

2. Internal

Toner cartridge Drum cartridge

13 14

16 17

1 Front cover 2 Side cover 3 Fusing unit release lever

4 Transfer charger 5 Charger cleaner

AR-208S/208D EXTERNAL VIEWS AND INTERNAL STRUCTURES 4 - 1

3. Operation panel

AR-208D

67 8 1011 1312 14 159

1 [MODE SELECT] key / Mode indicators

Press this key to select the mode. The indicator of the selected mode lights (copy, printer, scanner, fax mode indicators).

3 Numeric keys

Use these to enter the number of copies and other numerical settings.

The keys can also be used to select items in function setting menus.

5 Power save indicator

This lights up when the power save function is activated.

7 Error indicator

This lights steadily or blinks when a paper misfeed or other error occurs.

9 Tray location indicator

Indicates the selected paper tray. The indicator blinks when the tray is out of paper during operation or is not closed properly.

11 [2-SIDED COPY] key (AR-208D)

[2-SIDED SCAN] key (AR-208S)

Press in copy mode to select one-sided or two-sided settings for the original and for the output.

13 [ ] key ( ), [ ] key ( ), [ENTER] key

Press the [ ] key ( ) or [ ] key ( ) to select an item in a function setting menu.

Press the [ENTER] key to enter a selection.

15 [COPY RATIO] key

Press to select an enlargement or reduction ratio. To select a preset ratio setting, press the [COPY RATIO] key and

select the desired preset ratio. To select a ratio that is not preset, press the [COPY RATIO] key, select the preset ratio that is closest to the desired ratio, and then press the [ ] key ( ) or [ ] key ( ) to increase or decrease the ratio in increments of 1%.

17 [START] key ( ) / Ready indicator

The ready indicator lights up when copying or scanning is possible.

To begin copying, press the [START] key ( ). The [START] key ( ) is also pressed to return to normal

operation from auto power shut-off mode.

19 Shows the selected paper size. 20 Shows the number of copies that has been entered with the

21 A checkmark " " appears when the exposure has been

changed, or when two-sided copying, sort, 2 IN 1, or margin shift is selected.

34 5

Display

READY TO COPY. 100% 8.5x11 0

18 19

2 Display

This shows messages indicating the machine status and any problems that occur, as well as user programs and function setting menus.

4 [CLEAR] key ( )

Use this to clear the set number of copies, as well as cancel a job that is in progress. When a setting menu appears, use this key to move back to the previous menu level.

6 RSPF indicator

This lights up when an original is placed in the RSPF.

8 [TRAY SELECT] key ( )

Use to select the paper tray that has the desired paper for copying.

10 [MENU] key

Press this key to select the paper size for copying, to configure a user program or to display the total count.

12 [E-SORT/SP.FUN] key

Press to select the sort function, 2 IN 1 copy function, or margin shift function.

14 [EXPOSURE] key

Use to switch from auto exposure adjustment to text mode or photo mode.

16 [CLEAR ALL] key ( )

This returns all functions to the default settings. When pressed in a setting menu, this returns the settings and display to the initial state.

18 Shows the current copy ratio.

numeric keys.

AR-208S/208D EXTERNAL VIEWS AND INTERNAL STRUCTURES 4 - 2

4. Motors, solenoids and clutch

No. Part name Control signal Function / Operation

1 Main motor MM Drives the copier.

2 Scanner motor MRMT Drives the optical mirror base (scanner unit).

3 Toner motor TM Supplies toner.

4 Cooling fan motor VFM Ventilate the fuser section.

5 Resist roller solenoid RRS Resist roller rotation control solenoid

6 Paper feed solenoid CPFS1 Cassette Paper feed solenoid 1

7 Multi paper feed solenoid MPFS Multi manual pages feed solenoid

8 Drive motor SPMT Drives the RSPF.

9 Duplex motor DMT Devices the duplex paper transport section (Duplex model only) 10 Shifter motor SFTM Drives the shifter. 11 Reverse clutch SRVC Reverses the rotating direction of the roller. 12 Paper feed solenoid (RSPF) SPUS Feeds paper.

AR-208S/208D EXTERNAL VIEWS AND INTERNAL STRUCTURES 4 - 3

5. Sensors and switches

No. Name Signal Type Function Output

1 Scanner unit home position

sensor 2 POD sensor POD Transmission sensor Paper exit detection "H" at paper pass 3 PPD2 sensor PPD2 Transmission sensor Paper transport detection 2 "L" at paper pass 4 Cassette detection switch CED1 Micro-switch Cassette installation detection "H" at cassette insertion 5 PPD1 sensor PPD1 Transmission sensor Paper transport detection 1 "L" at paper pass 6 Door switch DSW Micro-switch Door open/close detection

7 Paper empty sensor SPID Transmission sensor Paper entry detection "H" paper empty 8 Paper exit sensor SRJD Transmission sensor Paper exit detection "H" paper empty 9 PD1 sensor PD1 Micro-switch Paper width detect "H" at A4 size or less

10 Upper door open/close sensor SCOD Transmission sensor Cover open/close detection "L" open 11 Paper sensor SPPD Transmission sensor Paper transport detection "H" paper empty

MHPS Transmission sensor Scanner unit home position detection "H" at home position

1 or 0V of 24V at door open

(safety switch for 24V)

"L" at A4 size or more

AR-208S/208D EXTERNAL VIEWS AND INTERNAL STRUCTURES 4 - 4

6. PWB unit

No. Name Function

1 Exposure lamp invertor PWB Exposure lamp (CCFL) control 2 Main PWB (MCU) Copier control 3 Operation PWB Operation input/display 4 High voltage PWB High voltage control 5 CCD sensor PWB For image scanning 6 LSU motor PWB For polygon motor drive 7 TCS PWB For toner sensor control 8 LSU PWB For laser control 9 FAX-operation PWB FAX operation input (AR-FX13 option)

10 Power PWB AC power input, DC voltage control 11 Modem PWB FAX control (AR-FX13 option)

AR-208S/208D EXTERNAL VIEWS AND INTERNAL STRUCTURES 4 - 5

7. Cross sectional view

41 2

15 16 1753 18

19 20

111214 13

No. Part name Function and operation

1 Scanner unit Illuminates the original with the copy lamp and passes the reflected light to the lens unit (CCD). 2 Exposure lamp Exposure lamp (CCFL) Illuminates original 3 LSU (Laser unit) Converts the original image signal into laser beams and writes onto the drum. 4 Paper exit roller Roller for paper exit 5 Main charger Provides negative charges evenly to the drum surface. 6 Heat roller Fuses toner on the paper. (Teflon roller) 7 Pressure roller Fuses toner on the paper. (Silicon rubber roller) 8 Drum Forms images. 9 Transfer unit Transfers images onto the drum.

10 Pickup roller Picks up the manual feed paper. (In multi feed only) 11 Manual paper feed tray Tray for manual feed paper 12 Manual paper feed roller Transport the paper from the manual paper feed port. 13 PS roller unit Takes synchronization between the lead edge and the rear edge of the paper. 14 Paper feed roller Picks up a sheet of paper from the cassette. 15 Pickup roller Picks up documents. 16 Separation roller Separates documents to feed properly. 17 Upper transport roller Transports of a document. 18 Paper exit roller Discharges documents. 19 Lower transport roller Transports of a document. 20 PS roller Feeds documents to the scanning section.

AR-208S/208D EXTERNAL VIEWS AND INTERNAL STRUCTURES 4 - 6

[5] UNPACKING AND

INSTALLATION

1. Copier installation

Improper installation may damage the copier. Please note the following during initial installation and whenever the copier is moved.

Caution: If the copier is moved from a cool place to a warm place,

condensation may form inside the copier. Operation in this condition will cause poor copy quality and malfunctions. Leave the copier at room temperature for at least 2 hours before use.

Do not install your copier in areas that are:

• damp, humid, or very dusty

• exposed to direct sunlight

2. Cautions on handling

Be careful in handling the copier as follows to maintain the performance of this copier.

Do not drop the copier, subject it to shock or strike it against any object.

Do not expose the drum cartridge to direct sunlight. Doing so will damage the surface (green portion) of the drum car-

tridge, causing poor print quality.

• poorly ventilated

• subject to extreme temperature or humidity changes, e.g., near an air conditioner or heater.

The copier should be installed near an accessible power outlet for easy connection.

Be sure to connect the power cord only to a power outlet that meets the specified voltage and current requirements.

Also make certain the outlet is properly grounded. Be sure to allow the required space around the machine for servic-

ing and proper ventilation.

Store spare supplies such as drum cartridges and toner cartridges in a dark place without removing from the package before use.

If they are exposed to direct sunlight, poor print quality may result. Do not touch the surface (green portion) of the drum cartridge. Doing so will damage the surface of the cartridge, causing poor

print quality.

3. Checking packed components and accessories

Open the carton and check if the following components and accessories are included.

Operation manual

Software CD-ROM

Drum cartridge (installed in unit)

(10cm)

8" (20cm)

8"(20cm)

4" (10cm)

AR-208S/208D UNPACKING AND INSTALLATION 5 - 1

4. Unpacking

Be sure to hold the handles on both sides of the machine to unpack the machine and carry it to the installation location.

6. Developer unit installation

1) 2) 3) Open the side and front cabinets of the copier.

4) Remove the locking tape of the developer unit.

5) Remove the screw which is fixing the copier and Developer unit.

6) Remove Developer unit slowly from the copier.

5. Removing protective packing materials

1) Remove all pieces of tape shown in the illustration below and

then open the RSPF and remove the protective materials. Take out the bag containing the toner cartridge.

2) Release the scan head locking switch.

Grasp here and turn in the direction of the arrow.

(A)

Lock Unlock

7) Remove the screw (1 pc).

8) Remove Upper developer unit.

3) Open the bypass tray, and then open the side cover while

pressing the side cover open button.

4) Remove the CAUTION tape from the front cover and remove

the two protective pins from the fusing machine by pulling the strings upward one at a time.

Protective pins

CAUTION tape

AR-208S/208D UNPACKING AND INSTALLATION 5 - 2

9) Shake the aluminum bag to stir developer

10) Supply developer from the aluminum bag to the top of the MX roller evenly.

Note: Be careful not to splash developer outside Developer

unit.

11) Attach Upper developer unit and fix it with a screw.

12) Rotate the MG roller gear to distribute developer evenly.

Note: Never rotate the gear in the reverse direction. Note: When carrying Developer unit, do not tilt it extremely as

shown with the arrow in the figure below. (Prevention of splash of developer)

2) Hold the section of Toner unit shown in the figure below, remove the packing tape, and remove the cushion.

3) Pull out the cushion in the arrow direction.

4) Insert Toner unit carefully into the copier.

5) Insert until the hook is engaged with the copier as shown in the figure below.

13) Insert Developer unit carefully into the copier. Note: Quick insertion may result in splash of developer. Be

sure to insert carefully.

14) Confirm that Developer unit is completely inserted to the bottom of the machine, fix Developer unit and the machine with a screw.

15) Completion of Developer unit installation

7. Toner cartridge installation

1) To prevent against uneven distribution of toner, hold Toner unit with both hands and shake it several times horizontally.

6) Pull out the shutter in the arrow direction.

Note: Do not hold and carry the shutter. Otherwise the shutter

may drop and Toner unit may drop.

7) Completion of Toner unit installation Close the front and side cabinets.

AR-208S/208D UNPACKING AND INSTALLATION 5 - 3

8. Loading the paper tray

Note: Make sure that the paper is not torn, is free of dust, and has

no wrinkles or curled edges.

1) Raise the handle of the paper tray and pull the paper tray out until it stops.

2) Remove the pressure plate lock. Rotate the pressure plate lock in the direction of the arrow to remove it while pressing down on the pressure plate of the paper tray.

5) Fan the paper and insert it into the tray. Make sure that the edges go under the corner hooks.

Note:

• Do not load paper above the maximum height line ( ).

Exceeding the line will cause a paper misfeed.

• If the paper is not fanned, double-feeds or misfeeds may occur.

• Make sure the stack of paper is straight before loading it. When

adding paper, take the remaining paper out and combine it into a single stack with the new paper.

• Make sure that all the paper in the stack is the same size and

type.

• When loading paper, ensure that there is no space between the

paper and the guide, and make sure that the guide is not set too narrow and causes the paper to bend. Incorrect loading will cause the paper to skew or misfeed.

3) Store the pressure plate lock which has been removed in step

2. To store the pressure plate lock, rotate the lock to secure it as shown below.

Pressure plate lock

4) Squeeze the lock lever of the front guide and slide the paper guide (A) to match the width of the paper, and move the paper guide (B) to the appropriate slot as marked on the tray.

Paper guide (B)

• The front guide is a slide-type guide. Grasp the locking knob

on the guide and slide the guide to the indicator line of the paper to be loaded.

• The left guide is an insert-type guide. Remove it and then

insert it at the indicator line of the paper to be loaded.

Paper guide (A)

6) Gently push the paper tray back into the machine. Note:

• If you loaded a different size of paper than was loaded previously in the tray.

• When not using the machine for an extended period, remove all paper from the paper tray and store it in a dry place. If paper is left in the machine for an extended period, the paper will absorb moisture from the air, resulting in paper jams.

9. Power to copier

1) Ensure that the power switch of the copier is in the OFF posi-

tion. Insert the attached power cord into the power cord socket at the rear of the copier.

2) Plug the other end of the power cord into the nearest outlet.

3) The document stopper may fall down by vibrations during transit

of the product. If documents are set under such a state, the JAM display may be indicated.

If the JAM display is indicated, remove the documents, turn OFF/ON the power SW, complete initializing of the RSPF, then set the documents again.

AR-208S/208D UNPACKING AND INSTALLATION 5 - 4

10. Software

The CD-ROM that accompanies the machine contains the following software:

MFP driver

Printer driver

The printer driver enables you to use the printer function of the machine.

The printer driver includes the Print Status Window. This is a utility that monitors the machine and informs you of the printing status, the name of the document currently being printed, and error messages.

Please note that the Print Status Window does not operate when the machine is used as a network printer.

Scanner driver*

The scanner driver allows you to use the scanning function of the machine with TWAIN-compliant and WIA-compliant applications.

Sharpdesk*

Sharpdesk is an integrated software environment that makes it easy to manage documents and image files, and launch applications.

Button Manager*

Button Manager allows you to use the scanner menus on the machine to scan a document.

*: The scanning feature can only be used with computers that are

connected to the machine by a USB cable.

A. Before installation

Hardware and software requirements

Check the following hardware and software requirements in order to install the software.

Computer type IBM PC/AT or compatible computer equipped

with a USB 2.0/1.1*

Operating

2 *3

system*

Windows 98, Windows Me, Windows 2000 Professional*

Windows XP Home Edition* Display 1024 x 768 dots (XGA) display with 16bit Hard disk free

150 MB or more space

Other hardware requirements

An environment on which any of the operating

systems listed above can fully operate

*1: Compatible with Windows 98, Windows Me, Windows 2000

Professional, Windows XP Professional, Windows XP Home Edition or Windows Vista preinstalled model standardly

equipped with a USB port. *2: Printing is not available in MS-DOS mode. *3: The machine does not support printing from a Macintosh envi-

ronment. *4: Administrator's rights are required to install the software using

the installer.

Installation environment and usable software

The following table shows the drivers and software that can be installed for each version of Windows and interface connection method.

Cable

Operating

system

USB Windows 98/

Me/2000/XP/ Vista

*1: The printer driver that is installed will vary depending on the

type of connection between the machine and your computer.

Install the software according to the Operation Manual.

Printer

driver

Available*

, Windows XP Professional*4,

Scanner

driver

, Windows Vista*

Button

Manager

Sharpdesk

Available

B. Installing the software

Note:

• The screen images in this manual are mainly for Windows XP. With other versions of Windows, some screen images may be different from those in this manual.

• In the following explanations it is assumed that the mouse is configured for right hand operation.

• If an error message appears, follow the instructions on the screen to solve the problem. After the problem is solved, the installation procedure will continue. Depending on the problem, you may have to click the "Cancel" button to exit the installer. In this case, reinstall the software from the beginning after solving the problem.

1) The USB cable must not be connected to the machine. Make

sure that the cable is not connected before proceeding. If the cable is connected, a Plug and Play window will appear. If

this happens, click the "Cancel" button to close the window and disconnect the cable.

Note: The cable will be connected in step 13).

2) Insert the CD-ROM into your computer's CD-ROM drive.

3) Click the "start" button, click "My Computer", and then double-

click the CD-ROM icon.

• In Windows Vista, click the "Start" button, click "Computer", and then double-click the CD-ROM icon.

• In Windows 98/Me/2000, double-click "My Computer", and then double-click the CD-ROM icon.

4) Double-click the "setup" icon. In Windows Vista, if a message screen appears asking you for

confirmation, click "Allow".

5) The "SOFTWARE LICENSE" window will appear. Make sure that you understand the contents of the software license, and then click the "Yes" button.

Note: You can show the "SOFTWARE LICENSE" in a different lan-

guage by selecting the desired language from the language menu. To install the software in the selected language, continue the installation with that language selected.

6) Read the "Readme First" in the "Welcome" window and then click the "Next" button.

7) To install all of the software, click the "Standard" button and go to step 12).

To install particular packages, click the "Custom" button and go to next step.

AR-208S/208D UNPACKING AND INSTALLATION 5 - 5

8) Click the "MFP Driver" button. Click the "Display Readme" button to show information on pack-

ages that are selected.

9) Select "Connected to this computer" and click the "Next" button. Follow the on-screen instructions.

Installing the Utility Software

11) Click the "Button Manager" or the "Sharpdesk" button. Click the "Display Readme" button to show information on pack-

ages that are selected. Follow the on-screen instructions.

Caution: In Windows 98/Me/2000, if the following screen appears,

click the "Skip" button or the "Continue" button as appropriate to continue the Sharpdesk installation.

If "Skip" is selected, the Sharpdesk installation will continue without installing Sharpdesk Imaging.

If "Continue" is selected, Sharpdesk Imaging will be installed. If Imaging for Windows is installed on your computer, Sharpdesk Imaging will overwrite Imaging for Windows.

Caution:

• If you are using Windows Vista and a security warning window appears, be sure to click "Install this driver software anyway".

• If you are running Windows 2000/XP and a warning message appears regarding the Windows logo test or digital signature, be sure to click "Continue Anyway" or "Yes".

10) You will return to the window of step 8). If you wish to install But-

ton Manager or Sharpdesk, click the "Utility Software" button. If you do not wish to install the Utility Software, click the "Close"

button and go to step 12).

Note: After the installation, a message prompting you to restart

your computer may appear. In this case, click the "Yes" button to restart your computer.

12) When installing is finished, click the "Close" button. Caution:

• If you are using Windows Vista and a security warning window appears, be sure to click "Install this driver software anyway".

• If you are running Windows 2000/XP and a warning message appears regarding the Windows logo test or digital signature, be sure to click "Continue Anyway" or "Yes".

A message will appear instructing you to connect the machine to your computer. Click the "OK" button.

Note: After the installation, a message prompting you to restart

your computer may appear. In this case, click the "Yes" button to restart your computer.

13) Make sure that the power of the machine is turned on, and then

connect the USB cable. Windows will detect the machine and a Plug and Play screen

will appear.

AR-208S/208D UNPACKING AND INSTALLATION 5 - 6

14) Follow the instructions in the plug and play window to install the driver.

Follow the on-screen instructions.

Caution:

• If you are using Windows Vista and a security warning window

appears, be sure to click "Install this driver software anyway".

• If you are running Windows 2000/XP and a warning message

appears regarding the Windows logo test or digital signature, be sure to click "Continue Anyway" or "Yes".

This completes the installation of the software.

• If you installed Button Manager, set up Button Manager as

explained in "C. Setting up Button Manager".

• If you installed Sharpdesk, the Sharpdesk setup screen will

appear. Follow the instructions in the screen to set up Sharpdesk.

(1) Connecting a USB cable

Follow the procedure below to connect the machine to your computer.

A USB cable for connecting the machine to your computer is not included with the machine. Please purchase the appropriate cable for your computer.

Caution:

• USB is available with a PC/AT compatible computer that was orig-

inally equipped with USB and had Windows 98, Windows Me, Windows 2000 Professional, Windows XP or Windows Vista preinstalled.

• Do not connect the USB cable before installing the printer driver.

The USB cable should be connected during installation of the printer driver.

Note

• If the machine will be connected using a USB 2.0 port of your

computer, please purchase a USB cable that supports USB 2.0.

• To obtain the fastest USB 2.0 data transfer speed, "USB2.0

MODE SWITCH" in the machine's user programs must be set to "HI-SPEED". For more information, see "[12] USER PROGRAM".

• Use the machine's "HI-SPEED" mode only when using a com-

puter that is running Windows 2000/XP/Vista.

• Even when the Microsoft USB 2.0 driver is used, it may not be

possible to obtain full USB 2.0 speed if a PC card supporting USB 2.0 is used. To obtain the latest driver (which may enable a higher speed), contact the manufacturer of your PC card.

• Connection is also possible using a USB 1.1 port on your com-

puter. However, the specifications will be USB 1.1 specifications (FullSpeed).

1) Insert the cable into the USB connector on the machine.

(2) Using the machine as a shared printer

If the machine will be used as a shared printer on a network, follow these steps to install the printer driver in the client computer.

Note: To configure the appropriate settings in the print server, see

the operation manual or help file of your operating system.

1) Perform steps 2) through 6) in "Installing the software".

2) Click the "Custom" button.

3) Click the "MFP Driver" button. Click the "Display Readme" button to show information on pack-

ages that are selected.

4) Select "Connected via the network" and click the "Next" button.

2) Insert the other end of the cable into your computer's USB port.

AR-208S/208D UNPACKING AND INSTALLATION 5 - 7

5) Click the "Add Network Port" button. In Windows Vista, the "Add Network Port" button does not

appear.

6) Select the network printer that is shared and click the "OK" button.

Ask your network administrator for the server name and printer name of the machine on the network.

2) Click the "SHARP AR-XXXX" icon and select "Properties" from the "File" menu.

In Windows Vista, select "Properties" from the "Organize" menu.

3) In the "Properties" screen, click the "Events" tab.

4) Select "SC1:" from the "Select an event" pull-down menu.

5) Select "Start this program" and then select "Sharp Button Manager T" from the pull-down menu.

7) In the printer port selection window, verify the network printer that is shared and whether the machine is to be used as the default printer, make the selections and click the "Next" button.

Follow the on-screen instructions.

Caution:

• If you are using Windows Vista and a security warning window

appears, be sure to click "Install this driver software anyway".

• If you are running Windows 2000/XP and a warning message

appears regarding the Windows logo test or digital signature, be sure to click "Continue Anyway" or "Yes".

8) You will return to the window of step 3). Click the "Close" button.

Note: After the installation, a message prompting you to restart

your computer may appear. In this case, click the "Yes" button to restart your computer.

This completes the installation of the software.

C. Setting up Button Manager

Button Manager is a software program that works with the scanner driver to enable scanning from the machine.

To scan using the machine, Button Manager must be linked with the scan menu on the machine. Follow the steps below to link Button Manager to scanner events.

(1) Windows XP/Vista

1) Click the "start" button, click "Control Panel", click "Printers and Other Hardware", and then click "Scanners and Cameras".

In Windows Vista, click the "Start" button, select "Control Panel" and click "Hardware and Sound", and then click "Scanners and Cameras".

6) Click the "Apply" button.

7) Repeat Steps 4) through 6) to link Button Manager to "SC2:" through "SC6:".

Select "SC2:" from the "Select an event" pull-down menu. Select "Start this program", select "Sharp Button Manager T" from the pull-down menu, and then click the "Apply" button. Do the same for each ScanMenu through "SC6:".

When the settings have been completed, click the "OK" button to close the screen.

Button Manager is now linked to the scan menu (1 through 6). The scan settings for each of scan menu 1 through 6 can be

changed with the setting window of Button Manager. For the factory default settings of the scan menu and the proce-

dures for configuring Button Manager settings, see "Button Manager Settings" in the Online Manual.

(2) Windows 98/Me/2000

1) Click the "Start" button, select "Settings", and then click "Control Panel".

2) Double-click the "Scanners and Cameras" icon.

Note: If the "Scanners and Cameras" icon does not appear in Win-

dows Me, click "view all Control Panel options".

3) Select "SHARP AR-XXXX" and click the "Properties" button. In Windows Me, right click "SHARP AR-XXXX" and click "Prop-

erties" in the pop-up menu.

AR-208S/208D UNPACKING AND INSTALLATION 5 - 8

4) In the "Properties" screen, click the "Events" tab.

5) Select "SC1:" from the "Scanner events" pull-down menu.

11. Interface

A. USB

Connector

4-pin ACON UBR23-4K2200 Type-B connector

Cable

Shielded twisted pair cable (2 m (6 feet) Max.: high-speed transmission equivalent)

Pin configuration

The pin numbers and signal names are listed in the following table.

Pin No. Signal name

1+5V 2-DATA 3+DATA 4GND

6) Select "Sharp Button Manager T" in "Send to this application".

Note: If other applications are shown, deselect the checkboxes for

the other applications and leave only the Button Manager checkbox selected.

7) Click the "Apply" button.

8) Repeat Steps 5) through 7) to link Button Manager to "SC2:" through "SC6:".

Select "SC2:" from the "Scanner events" pull-down menu. Select "Sharp Button Manager T" in "Send to this application" and click the "Apply" button.

Do the same for each ScanMenu through "SC6:". When the settings have been completed, click the "OK" button

to close the screen.

Button Manager is now linked to the scan menu (1 through 6). The scan settings for each of scan menus 1 through 6 can be

changed with the setting window of Button Manager. For the factory default settings of the scan menu and the proce-

dures for configuring Button Manager settings, see "Button Manager Settings" in the Online Manual.

12. Moving

Moving instructions

When moving the unit, follow the procedure below. Note: When moving this unit, be sure to remove the toner cartridge

in advance.

1) Turn the power switch off and remove the power cord from the outlet.

2) Open the side cover and front cover, in that order. Remove the toner cartridge and close the front cover and side cover, in that order.

To open and close the side cover and front cover, and to remove the toner cartridge.

3) Raise the handle of the paper tray and pull the paper tray out until it stops.

4) Push the center of the pressure plate down until it locks in place and lock the plate using the pressure plate lock which has been stored in the front of the paper tray.

5) Push the paper tray back into the unit.

6) Lock the scan head locking switch.

Note: When shipping the unit, the scan head locking switch must

be locked to prevent shipping damage.

7) Close the multi-bypass tray and the paper output tray extension, and attach the packing materials and tape which were removed during installation of the unit.

8) Pack the unit into the carton.

AR-208S/208D UNPACKING AND INSTALLATION 5 - 9

13. Scanner moisture-proof kit

If the machine is installed in a highly humid environment, you can alleviate dew condensation inside the scanner by installing the scanner moisture-proof kit described below.

A. Components

Scanner moisture-proof kit (DKIT-0016QSZZ)

Name Part code Qty

1 Scanner condensation

prevention mylar 2 Optical right hole mylar B PSHEZ0469QSZZ 2 3 Scanner motor metal plate

cushion 4 Scanner upper surface cushion PMLT-0105QSZZ 1 5 Scanner motor lower mylar PSHEP0600QSZZ 1 6 Scanner UPG mylar J3 PSHEP0599QSZZ 1 7 Fan housing cushion PMLT-0108QSZ1 1

B. Precautions at installation

Clean the position where each cushion/mylar is attached with industrial alcohol before the work.

C. Attachment method

Turn the main switch to the "OFF" position and remove the power plug from the outlet.

1) Detach the RSPF. Detach the RSPF from the copier and softly place it on top of

the original table as shown below.

PSHEZ0493QSZZ 3

PMLT-0106QSZZ 2

3) Remove the rear cover for the document glass. <1> Remove the two screws and then remove the right glass

holder. <2> Slide the rear cover for the document glass to remove it. <3> Remove the table glass.

4) Attach the Scanner condensation prevention mylar at the 3 positions on the rear side of the main unit as described below.

Note: The hole should be covered with the mylar. Align the edge of the mylar to the R part (the yellow line in the

diagram below) so that the hole of the metal plate is covered as much as possible.

2) Remove the rear cabinet. <1> Unscrew the screw and remove the rear cabinet

shielding plate. (Save the screw.)

<2> Unscrew three screws and remove the rear cabinet. (Save

the screws.)

<3> Disconnect the connector of the RSPF, and remove the

RSPF from the machine.

Align the edge of the mylar to the R part (the yellow line in the diagram below) so that the hole of the metal plate is covered as much as possible.

AR-208S/208D UNPACKING AND INSTALLATION 5 - 10

Attach along the edge of the projection (the yellow line in the diagram below).

6) Attach the Scanner motor metal plate cushion at 1 position on the attachment plate of the motor on the rear side of the main unit.

Note: The hole on the top of the motor unit should be covered

with the mylar.

Align the edge of the metal plate and the edge of the cushion (the yellow line in the diagram below).

5) Attach the Optical right hole mylar B at the 2 positions shown in the diagrams below which are at the top of the rear side of the main unit.

Note: The holes should be covered with the mylar. Attach along the edge of the cushion (the yellow line in the dia-

gram below). Align with the inside line of the bent part (the yellow line in the

diagram below).

Stick the excessive part on the side.

Align with the raised part (the yellow line in the diagram below). Match the center of the mylar (in the horizontal direction) to the

center of the raised part.

20mm -25mm

Press and attach the cushion aligning it to the metal plate so that there will be no gap between them.

Stick the excessive part on the side.

AR-208S/208D UNPACKING AND INSTALLATION 5 - 11

7) Attach the Scanner upper surface cushion on the top and the rear side at the rear side of the main unit.

Align the cushion with the side of the raised part (the yellow line in the diagram below).

9) Attach the Scanner motor lower mylar at 1 position under the motor attachment plate on the rear side of the main unit.

Note: The mylar should cover the hole under the motor unit. Attach matching the hole (the yellow mark in the diagram) and

along with the side edge (the yellow arrow in the diagram). Disconnect the motor harness from the connector and take off

the snap band from the hole.

Do not cover this hole. Align the edge of the cushion with

the edge of the metal plate.

Bend the part which is sticking out to the rear side of the scanner and attach to the surface.

Press the cushion at the steps shown in the diagram so that there will be no gap.

Press the cushion to make sure all the holes are covered.

8) Bend the edge of the Scanner motor lower mylar and stick together.

Press the mylar with a sharp-pointed stick or something so that it is stuck correctly.

10) Attach the Scanner motor metal plate cushion covering the bottom part of the Scanner motor lower mylar.

Note: The hole under the motor unit should be covered. Attach the cushion to cover the gap between the mylar and the

metal plate (the yellow mark).

Stick the lower part of the cushion to the mylar, too.

Stick together. Stick together.

AR-208S/208D UNPACKING AND INSTALLATION 5 - 12

Press the cushion with a sharp-pointed stick or something to fill the gap between the mylar and the metal plate.

11) Attach the motor connector and the snap band to the original position.

13) Attach the Fan housing cushion to the cooling fan at the position shown in the diagram below.

Cover the top and the right side of the fan housing when you see the fan housing from the backside of the machine.

Note: Please make sure the double-sided tape is not exposed

where the cushion is sticking out from the edge of the fan housing.

12) Attach the Scanner UPG mylar J3 to cover the hole on the right side of inside of the scanner.

Note: The mylar should cover the hole shown by the arrow in

the diagram.

Attach along with the bent part of the metal plate and align the edge of the mylar with the line shown in the diagram (the yellow line in the diagram).

View from the arrow A

Back side

Reference position

Attach the cushion leaving 3 - 7mm

from the edge.

3 - 7mm

Attach the cushion leaving 3 - 7mm from the edge so that the gap between the Fan housing cushion and the filter of the rear cabinet is filled for sure.

14) Attach the parts removed in the items 1), 2), and 3).

AR-208S/208D UNPACKING AND INSTALLATION 5 - 13

+ 134 hidden pages