Seville Classics FRN04725 Assembly Instructions Manual

ASSEMBLY INSTRUCTIONS

3-Tier Bookcase (Model # FRN04725)

32 in × 13 in × 33 in

(81.3 cm × 33.0 cm × 83.8 cm)

Patents Pending

Classic Lines Collection (Page 5 of 5)

The full “Classic Lines” furniture collection can be found at

www.sevilleclassics.com

Media Center/Coffee Table (FRN04715)

Wine Rack (FRN04716)

Magazine Rack (FRN04717)

2-Tier Tower (FRN04721)

Assembly Instructions (Page 4 of 5)

CAUTION:

1) Do NOT overly tighten the screws. Doing so may

damage the unit.

2) Do NOT place the unit in high temperature area or

near appliances that emit large amount of heat.

3) Do NOT place the unit outdoor, as exposure to direct

sunlight may cause the color to fade.

4) Do NOT place the unit on uneven surfaces. Doing so

may cause the unit to tip over.

5) Examine the screws periodically and tighten them if

they are loose.

6) Weight capacity: 75 lb per shelf

If you are missing any parts, have any questions, or need

additional assistance in assembly, please contact our

bilingual (English & Spanish) Customer Service

Department at:

Seville Classics, Inc.

Torrance, CA 90501 USA

Telephone: [phone] toll free within USA

310-533-3800

Fax: [phone]

Monday through Friday 8:30am - 4:30pm

(Pacific Standard Time)

E-mail: [e-mail]

Website and Online Store: www.sevilleclassics.com

Rev. 06/10

Parts List (Page 1 of 5)

Please check all the parts you received according to the

parts list below. If you are missing any parts, please

contact our Customer Service Department. (Please refer

to page 4 of 5)

(A) (B)

Folded Bookcase (1 pc)

(A) Long Screw (9 pcs)

pre-inserted in the unit

(B) Short Screw (6 pcs)

(C)

(D)

Bracket (4 pcs)

Bracket Screw (8 pcs)

*Tool needed: Phillips Screwdriver

Assembly Instructions (Page 2 of 5)

Step 1: Use a Phillips screwdriver to loosen the 9 long

screws (A) that have already been pre-inserted in the unit.

Do NOT remove the screws from the unit. Simply loosen

them to allow the unit to unfold. Next, place the

compressed unit horizontally and position your hands to

carefully unfold the unit.

Please Note:

1) Do NOT place the unit vertical when unfold as this may

result in the unit suddenly unfolding and pinching your

fingers.

2) Find a flat surface or floor to assemble the unit. Using

an uneven surface or floor to assemble the unit may result

in uneven/unlevel shelves.

3) If the unit is uneven/unlevel after assembled, loosen

both screws (A and B), adjust the unit and then retighten

the screw (A and B).

Step 2: Refer to the picture on page 3 of 5. First, tighten

the 9 pre-inserted screws (marked “A” in the picture).

Next, screw in and tighten the 6 short screws into the 6

screw holes on the unit (these screw holes are marked

“B” in the picture). Do NOT over tighten the screws.

Assembly Instructions (Page 3 of 5)

Step 3: Use a Phillips screwdriver to screw in and tighten

a Bracket (C) using 2 Bracket Screws (D) at four corners

of the unit.

How to Fold the Bookcase (If Needed): First, fully

loosen and remove all 4 brackets (marked “C” in the

picture above) from the unit. Then, fully loosen and

remove all 6 short screws (marked “B” in the picture

above) from the unit. Next, fully loosen (about 5 turns),

but do NOT remove, the 9 remaining pre-inserted screws

(marked “A” in the picture above). Finally, carefully fold

down the unit. Please note that the unit CANNOT be

folded completely flat. Forcing the unit into a folded

position without first removing the 4 brackets, 6 short

screws and fully loosening the 9 pre-inserted screws may

result in irreparable damage to the unit.