SENSAPHONE EXPRESS QUICK REFERENCE GUIDE

SENSAPHONE® EXPRESS QUICK REFERENCE GUIDE

Parameter Description Key Sequence* Range Default

Parameter Description Key Sequence Response Default

Local Mute Turns off the local [SENSOR ON/OFF] On or Off off

alarm announcement + [MUTE]

Call Delay Time delay [SET #] + Min: 0 sec. 30 sec.

until first call is made [CALL DELAY] Max: 255 sec.

[ENTER]

Voice Reps Number of times alarm [SET] + [VOICE REPS] Min: 0 reps 3 reps

message is repeated per + [number key value] Max: 255 reps

phone call [ENTER]

Intercall Time Time delay between [SET] + [INTERCALL Min: 00:00 30 sec.

phone calls TIME] + [enter minutes] Max: 272:59

+ [ENTER] + [enter (min:sec)

seconds] + [ENTER]

Max Calls Number of calls until unit [SET] + [MAX CALLS] Min: 0 calls 100 calls

self-acknowledges + [number key value] Max: 255 calls

+ [ENTER]

Low Temp Low temperature [SET] + [LOW TEMP] Min: -60°F/-50°C 10°F

Limits† alarm limits + [number key value] Max: 300°F/150°C

+ [ENTER]

High Temp High temperature [SET] + [HIGH TEMP] Min: -60°F/-50°C 100°F

Limits† alarm limits + [number key value] Max: 300°F/150°C

+ [ENTER]

Input Recognition Length of time a fault [SET] + [REC TIME] + Min: 00:00 3 sec.

Time condition must exist [number for input] Max: 272:59

to trip an alarm + [min] + [ENTER]

+[secs] + [ENTER]

Power Recognition Length of time for [SET] + [REC TIME] Min: 00:00 5 min.

Time continuous power failure + [POWER] Max: 272:59

to trip an alarm + [minutes] + [ENTER] (min:sec)

+[seconds] + [ENTER]

Listen-in Time Length of listen-in time [SET] + [LISTEN TIME] Min: 0 sec 15 sec

during call-in status report + [number key for Max: 255 sec

seconds] + [ENTER]

Rings Until Answer Number of rings until unit [SET] + [RINGS] + Min: 1 ring 1 ring

answers an incoming call [number key] + Max: 32 rings

[ENTER]

* press [ENTER] after all Key Sequences starting with [SET].
†The sensor included with the Sensaphone Express has a range of only -60º to 175º F (-50º to 80ºC).

Input Enable/Disable Turns input alarm [SENSOR ON/OFF] On or Off Enabled

AC Power Alarm Turns power alarm [SENSOR ON/OFF] On or Off Enabled

Enable/Disable detection on or off + [POWER]

Temperature Scale Selects between [SENSOR ON/OFF] On (ºC) Fahrenheit

Security Code Prohibits unauthorized [SET] + [CODE] none

PAUSE/TONE

1) Used to enter a minus sign for negative temperature limits or temperature calibrations.

2) Used to program a 4 second pause into dialout phone numbers.

CODE Key

Used to program a “wait for answer” into dialout phone numbers.

SET/# Key

Used to program a “#” into dialout phone numbers.

WHAT IS/* Key

Used to program an “*” into dialout phone numbers.

PROGRAMMING THE SENSAPHONE® FOR USE WITH A PAGER

Press [SET/#] + [PHONE NUMBER] key + the phone number of the pager +
[PAUSE/TONE]* + the phone number of the Sensaphone® (+ optional [SET/#] if required

by your pager service) + [ENTER].

*NOTE:You may have to press the [PAUSE] key multiple times to coordinate with the delay in your

pager service’s answering function. We recommend you try pressing [PAUSE] twice.

Enable/Disable an Input: [0] + [input # key 1-4] [5=low temp] [6=high temp] [7=power]

Record a Message Remotely: [# key] + [input # key 1-4] or [9 to record ID]

Listen to a Recorded Alarm Message: [*] + [input # key 1-4] or [9 for ID message]

Turn On/Off the Output∆: ON: [O #6] + [N #6]; OFF: [O #6] [F #3]

∆

{pin #6 must be in the ON position for manual control}

detection on or off + [input number key]

Fahrenheit and Celsius + [TEMP] or Off (ºF)

programming changes + [4 digit code] +

[ENTER]

SPECIAL KEY FUNCTIONS:

REMOTE TOUCH-TONE COMMANDS

(press ANY key after Status Report “OK” to access Phone Commands)