Sega UFO CATCHER User Manual

Download

TABLE OF CONTENTS

BEFORE USING THE PRODUCT, BE SURE TO READ THE FOLLOWING: TABLE OF CONTENTS INTRODUCTION

HANDLING PRECAUTIONS

PRECAUTIONS REGARDING INSTALLATION LOCATION

2-1 LIMITATIONS OF USAGE

2-2 OPERATION AREA

PRECAUTIONS REGARDING PRODUCT OPERATION

3-1 BEFORE OPERATION

3-2 DURING OPERATION (PAYING ATTENTION TO CUSTOMERS)

PART DESCRIPTIONS

ACCESSORIES

INSTALLATION

6-1 SECURE THE UNIT AT THE INSTALLATION SITE (MANIPULATE THE ADJUSTERS)

6-2 REMOVE SHIPPING BRACKETS

6-3 ATTACH PARTITION

6-4 CONNECT POWER CORD

6-5 ACTIVATE POWER SUPPLY

PRECAUTIONS WHEN MOVING

PRIZE REPLACEMENT

GAME CONTENT

GAME BOARD

EXPLANATION OF TEST AND DATA DISPLAY

11-1 SWITCH UNIT AND CASH BOX

11-2 VFD DISPLAY CONTENT

11-3 EXPLANATION OF TEST MODE

DIP SW SETTINGS

••••••••••••••••••••••••••••••••••••••••••••••••••

••••••••••••••••

••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••

••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••

•••••••••••••••••••

••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••

•••••••••••••••••••••••••••••

••••••••••••••••••••••••••••••••••••••••••••••••••••••••

••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••

•••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••

••••••••••••••••••••••••••••••••••••••••••••••

•••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••

•••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••

•••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••

••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••

•••••••••••••••••••••••••••••••••••••••••••

•••••••••••••••••••••••••••••••••••••••••••••••••••••

••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••

•••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••

•••••••••••••••••••••••••••

••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••

••••••••••••••••••••••••••••••••••••••••••••••••••••••••••

E1-0605 420-6953

ARM MECHANISM

13-1 ARM REPLACEMENT

13-2 ADJUSTMENT OF SENSOR BRACKET POSITION

13-3 SPRING STRENGTH ADJUSTMENT AND SPRING REPLACEMENT

13-4 SHOVEL REPLACEMENT AND ADJUSTMENT

13-5 OPEN ARM ANGLE ADJUSTMENT

MAINTENANCE OF Z-ORIENTED MECHANISM

COIN SELECTOR

15-1 REMOVING THE COIN SELECTOR

15-2 REMOVING A JAMMED COIN

15-3 CLEANING THE COIN SELECTOR

15-4 COIN INSERTION TEST

REPLACEMENT OF FLUORESCENT LIGHTING, LAMPS, AND FUSES

16-1 FLUORESCENT LIGHTING REPLACEMENT

16-2 LAMP REPLACEMENT

16-3 FUSE REPLACEMENT

PERIODIC INSPECTION

ERROR MESSAGES

TROUBLESHOOTING

DESIGN-RELATED PARTS

OPTIONAL ITEMS

21-1 DOLLAR BILL VALIDATOR

21-2 SECURITY BAR

21-3 LCD UNIT (LCD CASE + CABLE COVER)

PARTS LIST

WIRE COLOR CODE TABLE

WIRING DIAGRAM

••••••••••••••••••••••••••••••••••••••••••••••••••••••••••

••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••

•••••••••••••••••••••••••••••••••••••••••••••

•••••••••••••••••••

••••••••••••••••••••••••••••••••••••••••••••••••••

••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••

••••••••••••••••••••••••••

••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••

••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••

•••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••

•••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••

••••••••

••••••••••••••••••••••••••••••••••••••••••••••••••••••

•••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••

••••••••••••••••••••••••••••••••••••••••••••••••••••

•••••••••••••••••••••••••••••••••••••••••••••••••••••••••

•••••••••••••••••••••••••••••••••••••••••••••••••••••••

••••••••••••••••••••••••••••••••••••••••••••••••••

••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••

•••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••

•••••••••••••••••••••••••••••••••••••••••••••••••••••••••••

••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••

•••••••••••••••••••••••••••••••••••••••••••••••

114

•••••••••••••••••••••••••••••••••••••••••••••••••••••••••

115

iii

INTRODUCTION

This manual is intended to provide detailed descriptions together with all the necessary information covering the general operation of electronic assemblies, electro-mechanicals, servicing control, spare parts, etc. for the product, "SEGA UFO CATCHER".

This manual is intended for the owners, personnel and managers in charge of operation of the product. Operate the product after carefully reading and sufﬁciently understanding the instructions.

In the unlikely event that the product does not function correctly, DO NOT allow anyone other than a technician to touch the internal system. Turn off the power to the machine, making sure to unplug the electrical cord from the outlet, and contact the ofﬁce listed below or the point-of-purchase for this product.

Use of this product is unlikely to cause physical injuries or damage to property. However, points that require special attention are indicated by thick underlining, the word "IMPORTANT" and the symbol below

Indicates important information that, if ignored, may result in the mishandling of the product and cause faulty operation or damage to the product.

IMPORTANT

Sega Amusements U.S.A., Inc.

800 Arthur Avenue, Elk Grove Village, IL 60007-5215, U.S.A.

TEL: 1-847-364-9787 TOLL FREE: 1-888-877-2669 FAX: 1-847-427-1065

Installation space: 1,683 mm (66.3 in) [Width] x 875 mm (34.4 in) [Depth] <Full options assembled: 989 mm (38.9 in) [Depth]> Height: 1,972 mm (77.6 in) Weight: 295 kg (650.4 lb) Power, maximum current: 267 W, 2.4 A (AC 120 V, 60 Hz)

SPECIFICATIONS

INTRODUCTION

Deﬁnition of 'Site Maintenance Personnel or Other Qualiﬁed Individuals'

Procedures not described in this manual or marked as ‘to be carried out by site maintenance personnel or other qualiﬁed professionals’ should not be carried out by personnel without the necessary skill or technology. Work carried out by unqualiﬁed persons may cause serious accidents, including electrocution.

Parts replacement, maintenance inspections and troubleshooting should be carried out by site maintenance personnel or other qualiﬁed professionals. This manual includes directions for potentially dangerous procedures which should only be carried out by professionals with the appropriate specialized knowledge.

The site maintenance personnel or other qualiﬁed professionals mentioned in this manual are deﬁned as follows:

Site maintenance personnel:

Individuals with experience in maintaining amusement equipment, vending machines, etc., working under the supervision of the owner/operator of this product to maintain machines within amusement facilities or similar premises by carrying out everyday procedures such as assembly, maintenance inspections, and replacement of units/expendable parts.

Activities to be carried out by site maintenance personnel:

Amusement equipment/vending machine assembly, maintenance inspection and replacement of units/expendable parts.

Other qualiﬁed professionals:

Persons employed by amusement equipment manufacturers, or involved in design, production, testing or maintenance of amusement equipment. The individual should have either graduated from technical school or hold similar qualiﬁcations in electrical/electronics/mechanical engineering.

Activities to be carried out by other qualiﬁed professionals:

Amusement equipment/vending machine assembly, repair/adjustment of electrical/electronic/mechanical parts.

HANDLING PRECAUTIONSAS

HANDLING PRECAUTIONS1

When installing or inspecting the machine, be very careful of the following points and pay attention to ensure that the player can enjoy the game safely. Non-compliance with the following points or inappropriate handling running counter to the cautionary matters herein stated can cause personal injury or damage to the machine.

• Before performing work, be sure to turn the power off and unplug the electrical cord from the outlet. Performing the work without turning the power off can cause an electric shock or short circuit. In the case work should be performed in the status of power on, this manual always states to that effect.

• To avoid an electric shock or short circuit, do not plug in or unplug quickly.

• To avoid an electric shock, do not plug in or unplug with a wet hand.

• Do not expose power cords or earth wires on the surface, (ﬂoor, passage, etc.). If exposed, the power cords and earth wires are susceptible to damage. Damaged cords and wires can cause an electric shock or short circuit.

• To avoid causing a ﬁre or an electric shock, do not put things on or damage the power cords.

• When or after installing the product, do not unnecessarily pull the power cord. If damaged, the power cord can cause a ﬁre or an electric shock.

• In case the power cord is damaged, ask for a replacement through where the product was purchased from or the ofﬁce herein stated. Using the cord as is damaged can cause ﬁre, an electric shock or leakage.

• Be sure to perform grounding appropriately. Inappropriate grounding can cause an electric shock.

• Be sure to use fuses meeting the speciﬁed rating. Using fuses exceeding the speciﬁed rating can cause a ﬁre or an electric shock.

• Completely make connector connections for IC BD and others. Insufﬁcient insertion can cause an electric shock.

• Speciﬁcation changes, removal of equipment, conversion and/or addition, not designated by SEGA are not permitted.

- Failure to observe this may cause a ﬁre or an electric shock. Non-compliance

with this instruction can have a bad inﬂuence upon physical conditions of the players or the onlookers, or result in injury during play.

- SEGA shall not be held responsible for damage, compensation for damage to

a third party, caused by speciﬁcation changes not designated by SEGA.

• Be sure to perform periodic maintenance inspections herein stated.

HANDLING PRECAUTIONSAS

• For the IC board circuit inspections, only the logic tester is allowed. The use of a

multiple-purpose tester is not permitted, so be careful in this regard.

• Static electricity from your body may damage some electronics devices on the

IC board. Before handling the IC board, touch a grounded metallic surface so that the static electricity can be discharged.

• Some parts are the ones designed and manufactured not speciﬁcally for

this game machine. The manufacturers may discontinue, or change the speciﬁcations of, such general-purpose parts. If this is the case, Sega cannot repair or replace a failed game machine whether or not a warranty period has expired.

• This game machine can be installed at a storefront but could tip over due to sudden strong drafts or building winds. It could also tip over from man-made loads. If the game machine does fall down, a serious accident could result. To prevent the machine from falling down, carry out the following procedures and make every effort to operate the machine safely.

- Never place the product at a site that is inclined or has level differences.

If there are inclines or level differences, make sure the site is level before placing the machine on it.

- Do not add decorations to the product that will cause its center of gravity to

be elevated. Also, be aware that there are cases in which it is illegal to add electrical units to the product interior.

- Make sure that the adjusters are always in contact with the ﬂoor.

- Use rope, chain, and/or ﬁxtures for securing furniture to secure the product so

that it will not fall down in an earthquake.

IMPORTANT

HANDLING PRECAUTIONSAS

CONCERNING THE STICKER DISPLAY

This SEGA product has stickers attached describing the product manufacture No. (Serial No.) and Electrical Speciﬁcations. When inquiring about or asking for repairs, mention the Serial No. and Name of Machine indicated on the Sticker. The Serial Number indicates the product register. Identical machines could have different parts depending on the date of production. Also, improvements and modiﬁcations might have been made after the publication of this manual. In order to ensure you order the correct parts, mention the Serial No. when contacting the applicable places.

CONCERNING WARNING DISPLAYS

FIG. 1

This SEGA product has warning displays on stickers, labels and/or printed instructions adhered/attached to or incorporated in the places where a potentially hazardous situation could arise. The warning displays are intended for accident prevention for customers and for avoiding hazardous situations relating to maintenance and servicing work. Some portions of the cabinet contain high voltage and may cause accidents if touched. When performing maintenance, be very careful of the warning displays. It is especially important that any complex repair and replacement work not mentioned herein should be performed by those technical personnel who have knowledge of electricity and technical expertise. In order to prevent accidents, caution any customer ignoring the warnings to cease and desist immediately.

SERIAL NO. DISPLAY

440-CS0245-EG

440-WS0286-EG

440-WS0027-EG

440-WS0002XEG

Same on 2P side

UL CERTIFICATION DISPLAY

440-CS0316-EG

PRECAUTIONS REGARDING INSTALLATION LOCATION

• Be sure to check the Electrical Speciﬁcations. Ensure that this product is compatible with the location’s power supply, voltage and frequency requirements. A plate describing Electrical Speciﬁcations is attached to the product. Non-compliance with the Electrical Speciﬁcations can cause a ﬁre and electric shock.

• This product requires a breaker and earth mechanism as part of the location facilities. Using the product without these can cause a ﬁre and electric shock.

• Ensure that the indoor wiring for the power supply is rated at 7A or higher. Noncompliance with the Electrical Speciﬁcations can cause a ﬁre and electric shock.

• Be sure to use an independent power supply equipped with an earth leakage breaker. Using a power supply without an earth leakage breaker can cause an outbreak of ﬁre if a power surge occurs.

• Putting many loads on one electrical outlet can cause generation of heat and a ﬁre resulting from overload.

• When using an extension cord, ensure that the cord is rated at 7A or higher. Using a cord rated lower than the speciﬁed rating can cause a ﬁre and electric shock.

This product is an indoor game machine. Do not install it outside. Even indoors, avoid installing in places mentioned below so as not to cause a ﬁre, electric shock, injury and/or malfunction.

- Places subject to rain or water leakage, or places subject to high humidity in the

proximity of an indoor swimming pool and or shower, etc.

- Places subject to direct sunlight, or places subject to high temperatures in the

proximity of heating units, etc.

- Places ﬁlled with inﬂammable gas or vicinity of highly inﬂammable/volatile

chemicals or hazardous matter.

- Dusty places.

- Sloped surfaces.

- Places subject to any type of violent impact.

- Vicinity of anti-disaster facilities such as ﬁre exits and ﬁre extinguishers.

- The operating (ambient) temperature range is from 5°C to 35°C (5°C to 30°C

with LCD).

2-1 LIMITATIONS OF USAGE

PRECAUTIONS REGARDING INSTALLATION LOCATION

• For the operation of this machine, secure a minimum area of 1.7 m (66.9 in) [W] x

1.6 m (60.0 in) [D]. <Full options assembled: 1.7 m (66.9 in) [W] x 1.8 m (70.9 in) [D]>

• Do not block the ventilation port on the top surface. Heat may build up and cause a ﬁre.

• SEGA shall not be held responsible for damage or compensation for damage to a third party, resulting from the failure to observe this instruction.

2-2 OPERATION AREA

In order to transport the machine into a building, the minimum necessary dimensions of the opening (of doors, etc.) are 0.9 m (35.4 in) [W] and 2 m (78.7 in) [H].

Electricity Consumption:

MAX. 2.4 A (AC 120 V, 60 Hz)

IMPORTANT

FIG. 2-2b Full Options Cabinet (See Section 21.)FIG. 2-2a Basic Cabinet

1.8m (70.9in)

0.1m (3.9in)

1.7m (66.9in)

2m (78.7in)

Ventilation port

1.7m (66.9in)

2m (78.7in)

1.6m (60.0in)

Ventilation port

PRECAUTIONS REGARDING PRODUCT OPERATION

3-1 BEFORE OPERATION

In order to avoid accidents, check the following before starting the operation:

• Check if all of the adjusters are in contact with the surface. If they are not, the cabinet can move and cause an accident.

• Do not place items over the ventilation port on the top surface. Heat may build up and cause a ﬁre.

• Do not put any heavy items on this product. Placing heavy items on the product can cause accidents or damage to parts.

• Do not climb on the product. Climbing on the product can cause accidents. To check the top portion of the product, use a stepladder.

• To avoid electric shock, check that none of the door & cover parts are damaged or missing.

• To avoid electric shock, short circuit and or parts damage, do not put the following items on or in the periphery of the product. Flower vases, ﬂowerpots, cups, water tanks, cosmetics, and receptacles/containers/vessels containing chemicals or water.

To avoid injury and trouble, be sure to pay attention to the behavior of visitors and players.

To avoid injury, be sure to provide sufﬁcient space by considering the crowd situation at the installation location. Insufﬁcient installation space can cause customers to bump into each other, causing trouble.

FIG. 3-1

Ensure that all the adjusters are in contact with the floor.

PRECAUTIONS REGARDING PRODUCT OPERATION

3-2 DURING OPERATION (PAYING ATTENTION TO CUSTOMERS)

To avoid injury and trouble, be sure to pay attention to the behavior of visitors and players.

• To avoid injury from falls and electric shocks due to spilled drinks, instruct the player not to place heavy items or drinks on the product.

• To avoid electric shocks and short circuits, do not allow customers to put hands and ﬁngers or extraneous matter in the openings of the product or small openings in or around the doors.

• To avoid falls and resulting injury, immediately stop the customer from leaning against or climbing on the product, etc.

• To avoid electric shocks and short circuits, do not allow customers to unplug the power plug without a justiﬁable reason.

• If hands or ﬁngers are placed deeper than necessary into the prize retrieval slot or coin return slot, they could get caught, resulting in injury. Caution is required, especially for small children.

• Immediately stop such violent acts as hitting and kicking the product. Such violent acts can cause parts damage or cause the cabinet to fall over, resulting in injury.

PART DESCRIPTIONS

FIG. 4a Overall View

FIG. 4b Rear Panel View

NOTE: For optional items, see Section 21.

CABINET

GLASS DOOR

CONTROL PANEL LEFT SIDE: 1P RIGHT SIDE: 2P

SERVICE DOOR

CASH BOX DOOR

PRIZE DOOR

UFO MECHANISM

BACK LID

AC UNIT

BILL VALIDATOR DOOR 2P

BILL VALIDATOR DOOR 1P

ACCESSORIES

Conﬁrm that the accessories listed in the table below are present when setting up the product. Accessories marked "Spare" in the usage note column are consumable items but included as spares.

TABLE 5 ACCESSORIES

DESCRIPTION: OWNER’S MANUAL Part No. (Qty.): 420-6953 (1) Usage notes & Diagram: This manual

Parts not labeled with part numbers are as yet unregistered or cannot be registered. Be sure to handle all parts with care, as some parts are not available for purchase separately.

OPERATOR’S KEY 220-5793-2-A002 (4) For opening/closing the glass door and service door

MASTER KEY 220-5793-2-A001 (2) For opening/closing the back lid

KEYS (3 TYPES) (2 of each)

- For cash box door

- For bill validator door 1P (left)

- For bill validator door 2P (right)

TRUSS SCREW (CHROME) 000-T00408-0C (2) For installation, see Section 6 [2]

POWER CORD 600-7326 (1) For installation, see Section 6 [6]

TAMPERPROOF WRENCH M4 540-0006-01 (1) Tool

NOTE: The wrench shown in the ﬁgure is provided as an

accessory tool but a driver type tool, the 540-0018 (DRIVER TAMPER M4), is also available. If you wish to purchase it, contact the ofﬁce indicated on these instructions or where the product was purchased.

ACCESSORIES

SHOVEL W30 EG-3405Y (4) For replacement, see Section 12-4

SHOVEL W40 MKW-2120 (4) For replacement, see Section 12-4

SHOVEL W60 EG-3404 (4) For replacement, see Section 12-4

ARM S UCS-3430 (4) For replacement, see Section 13

ARM L UCS-3432 (4) For replacement, see Section 13

SLIDE SPRING USS-3418 (2) Spare, see Section 13

INSTALLATION

To install the unit, follow these instructions in this manual carefully. If the unit is not installed properly, it may cause personal injury or damage to the machine.

Carry out the following ﬁve steps to assemble and install the product.

For assembly and installation, you need a Philips screwdriver, adjustable wrench (for 24mm hexagonal bolts) and the operator’s key.

OPERATOR’S KEY

PHILIPS SCREWDRIVER (For M4 screws)

WRENCH (for M16 HEXAGONAL BOLTS)

6-1 SECURE THE UNIT AT THE INSTALLATION SITE (MANIPULATE THE ADJUSTERS)

6-2 REMOVE SHIPPING BRACKETS

6-3 ATTACH PARTITION

6-4 CONNECT POWER CORD

6-5 ACTIVATE POWER SUPPLY

24 mm

INSTALLATION

Make sure that all the adjusters are in contact with the ﬂoor. Otherwise the cabinet may move, causing an accident.

6-1

SECURE THE UNIT AT THE INSTALLATION SITE (MANIPULATE THE ADJUSTERS)

The product comes with 4 casters and 4 adjusters (Figure 6-1a). After the installation site has been determined, have the adjusters come directly in contact with the ﬂoor, establish a gap of about 5 mm between the casters and the ﬂoor surface, and adjust the adjusters so that the game machine is level.

1. Move the product to the installation site.

2. Adjust the adjusters so that they come in contact with the ﬂoor. Use the wrench to adjust the heights of the adjusters so that the game machine is level.

3. After making adjustments, tighten the adjuster nut upwards so that the adjuster height is ﬁxed.

FIG. 6-1a Bottom View

FIG. 6-1b Adjuster in contact with ﬂoor

FIG. 6-1c Basic Cabinet FIG. 6-1d Full Options Cabinet

(See Section 21.)

A 1:100 scale view of the unit. Use it as a reference for installation site layout.

ADJUSTER (4)

CASTER (4)

ADJUSTER

Approximately 5mm

ADJUSTER

CASETER

Tighten nut upwards.

INSTALLATION

6-2 REMOVE SHIPPING BRACKETS

• Hold the parts to be removed ﬁrmly and then remove the screws that hold them in place. If parts are not held ﬁrmly, they may fall and cause an accident.

• Do not move the UFO mechanism while holding onto parts not described in the procedures. You may get your ﬁngers, etc., caught and be injured.

• The mechanism is secured in place for shipment so it will not be damaged during transport. Before activating the power supply, be sure to remove the shipping brackets used to secure the mechanism. If they are not removed, parts may get damaged.

• Shipping brackets are required for preventing damage during transport. Be sure to store them carefully.

1. Open the glass door with the operator’s key.

2. Remove the screw in the shipping bracket mechanism.

PHOTO 6-2a

PHOTO 6-2b

IMPORTANT

Unlock and open glass door. (The opposite side can be opened in similar fashion)

SHIPPING BRACKET MECHANISM

M4 x 8, with flat & spring washers

Z MECHANISM

SCREW (1)

INSTALLATION

3. Move the UFO mechanism to a location where it will be easy to work. Place hand as shown in the photo and move the mechanism. Do not move holding other parts as you may get your ﬁngers caught and be injured. Also, the mechanism itself may become damaged.

4. Remove the screw. Make sure to hold the shipping bracket mechanism so it will not fall down, then remove the screw.

5. Secure in place with the accessory truss screw.

6. Perform steps 3, 4, and 5 again on the opposite side.

PHOTO 6-2c

PHOTO 6-2d

PHOTO 6-2e

SHIPPING BRACKET MECHANISM

Remove

M4 x 8, with flat & spring washers

SCREW (1)

M4 x 8

TRUSS SCREW (1), chrome

INSTALLATION

7. Remove the two screws at the bottom of the shipping center bar.

8. Remove the screw at the top of the shipping center bar. Make sure to hold the shipping center bar, then remove the screw.

6-3 ATTACH PARTITION

When attaching the partition, insert the partition CL into the partition bracket CL.

PHOTO 6-2f

PHOTO 6-2g

PHOTO 6-3

SHIPPING CENTER BAR

M4 x 8, with flat & spring washers

SCREW (2)

SCREW (1) M4 x 8, with flat & spring washers

SHIPPING CENTER BAR

PARTITION CL

RTION BRACKET CL

INSTALLATION

• Use a power supply equipped with an electric leakage circuit breaker. If you use a power supply without an electric leakage circuit breaker, a short circuit may occur and start a ﬁre.

• After laying out the power cord on the ﬂoor, make sure that it is securely

protected from exposure. If the cord is exposed anywhere, it could easily be damaged if a customer should trip or stumble over it. Such damages could cause accidents from electrical shocks or short circuits. Either lay out the cord so it will not interfere with customer trafﬁc, or protect it with a cover.

6-4 CONNECT POWER CORD

1. There is an AC unit on the cabinet rear panel. The AC unit has a main switch and an inlet for connecting the power cord.

2. Conﬁrm that the main switch is OFF.

3. The power cord is inserted from the bottom of the cabinet and comes out through a hole in the AC unit. However, it is not absolutely necessary to pass the cord through the hole. In some cases, depending on the environment in which the unit will be used, you can connect the power cord directly into the inlet.

4. Insert the power cord connector into the inlet securely.

5. Insert the power cord plug into the power outlet securely.

6. Lay out the power cord. Place a cover over the laid out power cord so that it will be protected.

FIG. 6-4a AC Unit

PHOTO 6-4

FIG. 6-4b Power Card Layout

CIRCUIT PROTECTOR

MAIN SWITCH

MAIN SWITCH OFF

INLET

To power outlet

POWER CORD COVER

INSTALLATION

6-5 ACTIVATE POWER SUPPLY

On this product, there is a power supply switch on the AC unit on the cabinet rear panel and on the internal switch unit. (The internal switch unit is inside the service door. Use the operator’s key to open the service door.)

Even when both of these switches are ON, there will be no power unless the glass doors on right and left are closed securely. Normally, leave one of these switches ON and turn the other power supply switch ON/OFF to use. When the power supply is activated, the billboard, the internal ﬂuorescent lighting, and the left and right ﬂuorescent lights all turn on. Now we will check the operation (initialization) of all motors and sensors in the UFO mechanism of this product.

These operations are also carried out upon completion of the test mode. When in [Display mode], all of the 7-segment displays (numeric display, hereafter “7-seg display”) read “-”, the game cannot be played, and coins are returned. Initialization also does not take place. (See Section 12.)

INITIALIZATION

During initialization, the UFO mechanism moves in the following sequence. If an error is discovered during this series of operations, an error message is displayed and the UFO mechanism stops. (See Section 19)

1. UFO returns to home position (above the prize drop-out slot).

2. UFO moves toward the back of the cabinet. When it reaches the back limit, the UFO stops.

3. UFO moves sideways toward the center of the cabinet. When it reaches the center limit, the UFO stops.

4. UFO descends. When it reaches the lower limit, the UFO rises. Upon reaching the upper limit, the UFO stops.

5. UFO moves toward the front of the cabinet. When it reaches the front limit, the UFO stops.

6. UFO moves sideways toward the home position. Upon reaching the home position, the UFO stops. During stages 1 to 6 above, the UFO arm remains at the angle it assumed when the power supply was activated.

7. The UFO arm opens and closes.

8. After the arm closes, the catch sensor inside the UFO is initialized. This operation cannot be seen, but an error message will be displayed if there is an error in the sensor.

FIG. 6-5 Initialization of UFO mechanism on player 1 side (left seat)

When the above initialization procedures are complete, the customer-standby status is assumed. In this product, credits are remembered even if the power has been cut off. However, partial credits attained for multiple coins and bonus adder counts are deleted. If credits remain, the game-play status is assumed upon completion of initialization.

PRECAUTIONS WHEN MOVING

Carefully observe the following when moving the product. Failure to follow these instructions may result in personal injury during movement and/or damage to the cabinet.

• Disconnect the power cord plug before moving the product. Be careful not to damage the power cable during movement.

• To move the product over the ﬂoor, retract the adjusters and have the casters come in contact with the ﬂoor.

• After the casters are in contact with the ﬂoor, exercise special caution, as the unit could move by itself if the ﬂoor is inclined.

• To lift the cabinet, always lift it holding the bottom. If you lift the cabinet holding other areas, parts or attachments could be damaged due to the weight of the cabinet.

• Do not press on glass components while moving the product. Careless handling could cause damage to other parts. Fragments may also cause injury.

• When moving the cabinet over areas with level differences and the cabinet is projected to tilt due to the incline, attach shipping brackets and secure the UFO mechanism in place. If the UFO mechanism is not secured in place, parts could be damaged.

FIG. 7b

FIG. 7a

Move cabinet after casters are in contact with the floor

Do not press on glass components.

Do not press on glass components while moving the product. Otherwise glass may be damaged and cause injuries. Press on the cabinet's metal plates.

PRIZE REPLACEMENT

PRIZE REPLACEMENT8

• Observe and follow the conditions listed below for prizes used with this product. Failure to follow the conditions could lead to product malfunctions and components may be damaged. The prizes themselves may also be damaged.

• Prizes can be stacked up to a maximum height of 40 cm (15.7 in), and 800 g (1.8 lb) or less in weight. If this limit is exceeded, there could be product malfunctions and components may be damaged. The prizes themselves may also be damaged.

• Exercise special care when handling glass components. Careless handling could cause damage to the glass. Fragments may also cause injury.

• If the larger arm L has been attached, enlarge the prize drop-out slot for largesize prizes. Otherwise there could be malfunctions or damage when the arm makes contact. The prizes themselves may also be damaged.

• Do not place prizes on, or suspend them from, the mechanism rail or moveable parts. This could cause product malfunctions and components may be damaged.

• Even if prizes meet the conditions set forth in these instructions, there could be unexpected faulty operations due to prize materials, shapes, and/or centers of gravity.

Use the operator’s key to open the glass door, then place prizes in the play ﬁeld.

FIG. 8

Prizes can be stacked up to a maximum height of 40 cm (15.7 in), and 800 g (1.8 lb) or less in weight.

GLASS DOOR

PRIZE REPLACEMENT

CHANGING THE PRIZE DROP-OUT SLOT

If arm L has been attached for large-size prizes, enlarge the prize drop-out slot. (These instructions are for the 2P side drop-out slot.)

1. Loosen the 2 plastic-head screws.

2. Support the bottom of the corner partition and slide it to widen the drop-out slot. Do not press down on the top of the corner partition (acrylic) to slide. Excessive force could damage components.

3. Tighten the 2 plastic-head screws that were loosened.

PHOTO 8a

PHOTO 8b

PHOTO 8c

PLASTIC-HEAD SCREW (2) M4

PLASTIC-HEAD SCREW (2)

GAME CONTENT

GAME CONTENT9

The following explanations apply when the product functions normally. If the product behaves in a manner at variance with the content below, there may be a malfunction of some sort. Try to identify the cause of the problem immediately and repair it so that the unit can be operated normally.

HOW TO PLAY

In this product, the internal ﬂuorescent lighting (for both billboard and internal lighting), and the left and right ﬂuorescent lights light up when there is electrical continuity. During customer-standby status, the UFO mechanism is stationary at the home position (above the prize drop-out slot). All the buttons’ lights on the control panel go out and the BGM outputs standby music. The BGM can also be set for no output. Play fee and play count are displayed on the 7-seg displays on the control panel. When in [Display mode], all of the 7-seg displays read “-”, the game cannot be played, and coins (or bills) are returned. (See Section 12.)

1. When coins are inserted, the time remaining (how long the UFO mechanism can be operated) and the number of games remaining are displayed on the 7-seg displays at the seat that is being playing.

2. When 9 credits are exceeded, no more coins are accepted. (The coins are returned.) For example, if it is set so that 1 coin equals 2 credits and 8 credits have been established, the total becomes 10 credits when the next coin is inserted. At this time, the 7-seg display blinks alternately between “1” and “0” and no more coins can be accepted.

3. When the lever is manipulated, time count begins and the UFO mechanism moves in the direction in which the lever is manipulated.

4. The arm of the UFO mechanism opens automatically whenever time runs out or the DOWN BUTTON has been pressed.

FIG. 9a Customer-standby Status

FIG. 9b Control Panel

PRIZE DOOR

UFO mechanism is stationary at home position.

CONTROL PANEL

Fluorescent lamps are lit

LEVER

7-SEG DISPLAY CREDIT COUNT DISPLAY

DOWN BUTTON

GAME CONTENT

5. When the arm of the UFO mechanism opens completely, the UFO mechanism begins to descend.

6. Whenever the UFO mechanism comes in contact with a prize or other obstacle, or when the wire is stretched to its full length, the UFO mechanism stops descending and the arm closes.

7. After the arm has closed, the UFO mechanism begins to ascend. When it reaches the upper limit sensor, the UFO mechanism moves back to home position.

8. When the UFO mechanism reaches the home position, the arm opens.

9. When a prize passes the sensor, the fanfare rings.

10. When the arm opens and closes, 1 game is complete. If no credits remain at this time and the 7-seg display reads 0, the game is over. The BGM switches back to standby music. If credits remain, the next game can be played.

11. If the lever is not manipulated for 90 seconds, 1 credit is erased and the UFO mechanism arm opens and descends at the current position. The arm then closes and ascends and the UFO mechanism returns to home position.

FIG. 9c

GAME BOARD

GAME BOARD10

• Be careful not to damage the wires. Damaged wires may cause an electric shock, short circuit or present a risk of ﬁre.

• Do not expose the Game Board, etc. for any reason. Doing so may cause electric shock or malfunctioning.

The chip components on IC boards can be damaged by electrostatic discharge from the human body. Before handling an IC board, always neutralize any static charge in the body by touching a grounded metal surface.

To access the game board, remove the 2 tamperproof screws on the back side of the cabinet, then use the master key to remove the back lid. The game board is inside.

PHOTO 10

BACK LID GAME BOARD

M4 x 8

MPERPROOF SCREW (2), chrome

GAME BOARD

GAME BOARD CONFIGURATION DIAGRAM

The DIP SWs on the game board are not used for game settings but must all be set to OFF.

GAME BD UCU: 834-14606 (R)

[CN1 (JST RA34P)]: Switch, Analog Input [CN2 (JST RA50P)]: Switch, Sensor Input [CN3 (JST RA16P)]: Power Supply Input [CN4 (JST NH25P)]: Lamp, Catch Motor Output [CN5 (JST NH12P)]: Not used. [CN7 (JST RA40P)]: Meter, AC Motor Output [CN8 (JST NH4P)]: Speaker Output [CN9 (JST NH3P)]: Sound Volume Input [CN10 (JST NH16P)]: 7-seg Display Output [CN11 (JST NH10P)]: 7-seg Display Output [CN12 (JST NH6P)]: Not used. [CN14 (JST NH8P)]: Not used. [CN15 (JST NH5P)]: DIPSW BD Signal

CONNECTORS AND INPUT/OUTPUT

FIG. 10

CN7

CN8 NH4P

CN9 NH3P

CN18 NH16P

CN11 NH18P

LED2

LED1

DIPSW

RA34PRA50P

CN1CN2

CN12

NH6P CN3 RA16P

CN14 NH8P

POWER LED (This is lit when powering on.)

CN4 NH25P

CN15 NH5P

CN5 NH12P

RA40P

HEAT SINK

834-14606(R)

ROM

EXPLANATION OF TEST AND DATA DISPLAY

EXPLANATION OF TEST AND DATA DISPLAY11

11-1 SWITCH UNIT AND CASH BOX

Do not touch any areas other than those indicated. Touching other areas may cause accidents from electrical shocks or short circuits.

When you open the service door at the bottom of the cabinet front panel, you will ﬁnd a switch unit deep inside. The functions of each button on the switch unit are as described below.

- VFD Display: Monitor for displaying conditions such as income data.

- 1P Power Knob: Adjusts the strength of the 1P UFO mechanism spring. Adjustment ranges from 00 (weakest) to 99 (strongest).

- 2P Power Knob: Adjusts the strength of the 2P UFO mechanism spring. Adjustment ranges from 00 (weakest) to 99 (strongest).

- Select Button: Used when switching VFD display content.

- Clear Button: Used when clearing data displayed on VFD.

- Test Button: Separated for 1P and 2P. Used when entering the test mode and when completing the test mode.

FIG. 11-1

If the coin meter circuit is left detached, games cannot be played.

IMPORTANT

1P POWER KNOB (1P POWER)

1P SERVICE BUTTON (SERVICE)

2P POWER KNOB (2P POWER)

SOUND VOLUME (VOL)

DIP SW 1 DIP SW 4 (See Section 12.

)

METER 1 (METER 1)

CLEAR BUTTON (CLEAR)

SELECT BUTTON (SELECT)

2P SERVICE BUTTON (SERVICE)

2P TEST BUTTON (TEST)

1P TEST BUTTON (TEST)

METER 2 (METER 2)

SUB POWER SUPPLY SWITCH (SUB SW)

COIN METER 1P (COIN METER 1P) COIN METER 2P (COIN METER 2P)

VFD DISPLAY

EXPLANATION OF TEST AND DATA DISPLAY

- Service Button: Separated for 1P and 2P. Used when increasing the number of credits for service without tabulating the coin meter. If this button is pressed when an error has occurred, the error sound stops. If it is pressed in test mode, credits are cleared.

- Sound Volume: Adjusts the game music volume. Set for a suitable volume in consideration of the surrounding environment.

- Meter: Count content set with DIP SW2 is displayed on meter 1 and meter 2.

- Coin Meter: Separated for 1P and 2P. Counts the number of coins inserted in the coin slot.

- Sub Power Supply Switch: This is a power supply switch. The main switch is located on the AC unit on the cabinet rear panel. There is power when both switches are ON.

Open the cash box door to ﬁnd the cash box inside.

11-2 VFD DISPLAY CONTENT

Normally, the POWER setting screen is displayed. When the select button is pressed, the current credit status can be displayed on VFD. Each time the select button is pressed, the screen changes.

If there are no operations for 60 seconds, the POWER setting screen is restored. When the select button is kept depressed for 2 seconds or longer, [Current count] and [Total count] can be toggled. In [Current count], upon switching to [Service count since last clearing], the screen will return to [Income since last clearing]. In [Total count], upon switching to [Backup clear], the screen will return to [Total income count].

To clear data, enter test mode. Press the clear button when [CLEAR?] is displayed, and the data can be cleared. In [Current count], it is possible to clear the data but the data cannot be cleared without being in test mode (The clear screen will not be displayed).

In [Total count], backup data cannot be cleared without both 1P and 2P being in test mode (The clear screen will not be displayed). The data backup period lasts for two days after power has been cut off.

PHOTO 11-1

CASH BOX

EXPLANATION OF TEST AND DATA DISPLAY

DISPLAY CONTENT

[Current count]

Total counts since the data had last been cleared are displayed. Examples include today’s income, income after replacement of prizes, etc. (Data items can be cleared independently)

CURRNT COUNT

1P: 000000 current 2P: 000000 coin

1P CoinCount 000000 CLEAR?

2P CoinCount 000000 CLEAR?

1P: 000000 current 2P: 000000 prize

1P PrizeCount 000000 CLEAR?

2P PrizeCount 000000 CLEAR?

Current count

Income since last clearing Displays income count since data had last been cleared. (One unit = 25 cents)

Display during 1P test mode

Display during 2P test mode

Play count since last clearing Displays prize-out count since data had last been cleared.

Display during 1P test mode

Display during 2P test mode

EXPLANATION OF TEST AND DATA DISPLAY

1P: 000000 current 2P: 000000 credit

1P CreditCount 000000 CLEAR?

2P CreditCount 000000 CLEAR?

1P: 000% current 2P: 000% payout

1P: 000000 current 2P: 000000 service

1P ServiceCount 000000 CLEAR?

2P ServiceCount 000000 CLEAR?

Display during 2P test mode

Service count since last clearing Displays number of games played using service button since data had last been cleared.

Display during 1P test mode

Display during 2P test mode

Play count since last clearing Displays play count since data had last been cleared. Since this is the play count,

the display may differ from income depending on the setting.

Display during 1P test mode

Payout rate since last clearing

Displays rate calculated from play count and prize-out count since data had last been cleared.

EXPLANATION OF TEST AND DATA DISPLAY

[Total Count]

Even when data has been cleared in [Current count], data in total count is not erased. This data accumulates unless the backup data is cleared.

TOTAL COUNT

1P: 000000 total 2P: 000000 coin

1P: 000000 total 2P: 000000 prize

1P: 000000 total 2P: 000000 credit

1P: 000000 total 2P: 000000 payout

1P: 000000 total 2P: 000000 service

BACKUP DATA CLEAR?

Total count

Total income count Displays total income count until backup is cleared.

Total prize-out count Displays total prize-out count until backup is cleared.

Total play count Displays total play count until backup is cleared.

Total payout rate

Displays rate calculated from total play count and total prize-out count until backup is cleared.

Total service count Displays total service count until backup is cleared.

Backup data clear (Display when both 1P and 2P in test mode) All data can be cleared. ([Current count] and [Credit] are also cleared)

EXPLANATION OF TEST AND DATA DISPLAY

DISPLAY FLOW-CHART

The screen changes each time the select button is pressed. If no other buttons are pressed and no operations are performed for 60 seconds, the POWER setting screen is restored. When the select button is kept depressed for 2 seconds or longer, [Current count] and [Total count] can be toggled.

POWER SETTINGS

Spring strength can be changed within the range of 00 to 99 by turning the power knob. When the knob is turned to the right, the spring becomes stronger ( low level of difﬁculty ). When it is turned to the left, the spring becomes weaker ( high level of difﬁculty ). 1P and 2P can be changed independently. When the knob is turned, the POWER value is shown on the VFD. To display current POWER without turning the knob, press and hold down on the select button while pressing the clear button. Current POWER is shown on the VFD.

In the case shown in the ﬁgure above, 1P is set to high level of difﬁculty and 2P is set to low level of difﬁculty.

The power can be changed during operation so there is no need to reactivate the power supply. Power becomes effective after changes have been made.

FIG. 11-2

1P POWER: 00 2P POWER: 99

C U R R E N T C O U N T

T O TA L C O U N T

B A C K UP D AT A C L E A R ?

c u r r en t c o i n

1 P : 0 00 0 0 0

CURRENT COUNT TOTAL COUNT

TOT

AL INCOME COUNT

TOT

AL PRIZE-OUT COUNT

TOTAL PLAY COUNT

TOT

AL PLAYONT RATE

TOT

AL SERVICE COUNT

BACKEUP DATA CLEAR

INCOME SINCE LAST CLEARING

When in test mode, the following clear screens are displayed.

PRIZE-OUT SINCE LAST CLEARING

PLAY COUNT SINCE LAST CLEARING

PLAYOUT RATE SINCE LAST CLEARING

SERVICE COUNT SINCE LAST CLEARING

2 P : 0 00 0 0 0

1 P

0 0 0 0 00 C L E A R ?

c u r r en t p r i z

1 P : 0 00 0 0 0 2 P : 0 00 0 0 0

c u r r en t c r e d i

1 P : 0 00 0 0 0 2 P : 0 00 0 0 0

c u r r en t s e r v ic e

1 P : 0 00 0 0 0 2 P : 0 00 0 0 0

c u r r en t p l a y ou t

1 P : 0 00 % 2 P : 0 00 %

C o i n Co u n t

2 P

0 0 0 0 00 C L E A R ?

1 P

0 0 0 0 00 C L E A R ?

C o i n Co u n t

P r i z eC o u n t

2 P

0 0 0 0 00 C L E A R ?

P r i z eC o u n t

1 P

0 0 0 0 00 C L E A R ?

C r e d it C o u n t

2 P

0 0 0 0 00 C L E A R ?

C r e d it C o u n t

1 P

0 0 0 0 00 C L E A R ?

S e r v ic e C o u n t

2 P

0 0 0 0 00 C L E A R ?

S e r v ic e C o u n t

t o t a l c o i n

1 P : 0 00 0 0 0 2 P : 0 00 0 0 0

t o t a l p r i z

1 P : 0 00 0 0 0 2 P : 0 00 0 0 0

t o t a l c r e d i

1 P : 0 00 0 0 0 2 P : 0 00 0 0 0

t o t a l p l a y ou t

1 P : 0 00 0 0 0 2 P : 0 00 0 0 0

t o t a l s e r v ic e

1 P : 0 00 0 0 0 2 P : 0 00 0 0 0

EXPLANATION OF TEST AND DATA DISPLAY

11-3 EXPLANATION OF TEST MODE

When the test button is pressed, the mechanism stops operating and test mode is established. When in test mode, the test mode number is displayed on the 7-seg display. There are a total of 4 test mode types. Test mode number is changed using the down button and operation is done using the lever. To end test mode, press the test button once again.

When initialization completes normally, the credits before test mode are restored and game mode is re-established. However, partial credits attained for multiple coins are deleted.

Coins are not accepted during test mode. If the service button is pressed during test mode, credits are cleared.

Test Mode Number Operation Content

Test mode 1

UFO mechanism moves forward/backward/left/right as the lever is moved forward/backward/left/right.

Test mode 2 UFO mechanism moves up/down as the lever is moved forward/backward.

Test mode 3 When the lever is manipulated, the arm opens/closes repeatedly.

Test mode 4 Prize sensor and down switch lamp can be checked.

TABLE 11-3a

FIG. 11-3b

FIG. 11-3c

FIG. 11-3a

1 2

7-SEG DISPLAY

Sensor status, etc., are displayed in accordance with the test mode number. (See TABLE 11-3a.)

TEST MODE NUMBER DISPLAY

Moves forward/backward/left/right

Arm opens/closes

Moves up/down

EXPLANATION OF TEST AND DATA DISPLAY

Test Mode Number 7-Seg Display Reads Content

Test mode 1

7-seg 1 7-seg 2 7-seg 3 7-seg 4

Limit sensor LEFT Limit sensor RIGHT Limit sensor FWD Limit sensor BACK

Test mode 2

7-seg 1 7-seg 2 7-seg 3 7-seg 4

Limit sensor UP Limit sensor DOWN –––

–––

Test mode 3

7-seg 1 7-seg 2 7-seg 3 7-seg 4

Open sensor ––– ––– –––

Test mode 4

7-seg 1 7-seg 2 7-seg 3

7-seg 4 (Down switch also lights up in response to prize sensor)

Prize sensor ––– ––– –––

TABLE 11-3b

During test mode, the content for the small 7-seg display are as indicated below. If the limit sensor is entered or operation has just begun, “0” is displayed.

DIP SW SETTINGS

• Make sure the DIP SW that are designated to be OFF are turned OFF. If DIP SW are set to other than prescribed settings, there will be instances when behavior is not suited to actual operations.

• Changed settings do not become effective until the power supply has been reactivated after changing DIP SW.

• The DIP SW on the game board are not used for game settings but must all be set to OFF.

With this product, settings can be changed to those shown in the table by changing the DIP SW (DIP Switch) settings on the switch unit. DIP SW 1 adjusts coin credit settings; DIP SW 2 sets common game operations for 1P and 2P; DIP SW 3 and 4 set the game operations for 1P and 2P, respectively.

IMPORTANT

DIP SW SETTINGS

Turn off the power supply before changing DIP SW. If the power is left on while DIP SW are changed, electrical shock may occur.

COIN SETTINGS

Coin credit settings (credits awarded per coin) are set using DIP SW 1. When 9 credits are exceeded, no more coins are accepted and the coins are returned. However, if 1 coin is worth 2 credits or more, and 8 credits are remaining, 10 credits or more are established (10 credits or more can be established, depending on the setting).

For example, if it is set so that 1 coin equals 2 credits and 8 credits have been established, the total becomes 10 credits when the next coin is inserted. At this time, the 7-seg displays blink alternately between “1” and “0” and no more coins can be accepted. When FREE PLAY is selected, “ ” is shown on the 7-seg display and games can be played without engaging the coin and service switches.

SETTING COMMON GAME OPERATIONS FOR 1P AND 2P

Common game operations for 1P and 2P are set with DIP SW 2.

BGM SOUND

Sounds for when the unit is in customer-standby status or when a game is being played can be set. BGM1: Two music pieces change each time a game is completed.

BGM2: Game music is played also while in customer-standby status. BGM3: Two Christmas songs change each time a game is completed. BGM4: No music is heard during customer-standby status or game play.

FIG. 12

DIP SW 1~4

DIP SW SETTINGS

METER SETTINGS

TOTAL COIN (BILL=4COIN) / TOTAL PRIZE

- METER 1: 1P + 2P total coins are counted.

- METER 2: 1P + 2P total prizes are counted.

TOTAL COIN (25¢) /TOTAL BILL ($1)

- METER 1: 1P + 2P total 25-cent coins are counted.

- METER 2: 1P + 2P total $1-bills are counted.

1P PRIZE/2P PRIZE

- METER 1: 1P prizes are counted.

- METER 2: 2P prizes are counted.

1P BILL ($1) /2P BILL ($1)

- METER 1: 1P $1-bills are counted.

- METER 2: 2P $1-bills are counted.

CRIME PREVENTION MODE

To prevent theft, an alarm sounds whenever the prize sensor activates during customer-standby status.

PRIZE COUNT (during customer-standby)

If the prize sensor activates during customer-standby, there is an option to count it as a prize-out or not. (Prize-out is counted even while crime prevention mode is operating)

SETTING GAME OPERATIONS FOR 1P AND 2P SEPERATELY

Settings can be changed for game operations on the 1P side using DIP SW 3 and the 2P side using DIP SW 4.

PLAY TIME

Sets the time period during which manipulations can be made during game play.

GAME MODE

NORMAL MODE (1credit for 1game) 1 credit allows for 1 game to be played.

TIMER MODE (Games can be played any number of times during the time period.) Games can be played any number of times if still within the time period.

DISPLAY MODE

Setting so that games cannot be played (for display, etc.). In this mode, coins are not accepted and games cannot be played. All of the 7-seg displays read “-” and coins are returned. Initialization also does not take place.

PRIZE SENSOR

Setting to use the prize sensor. Prize sensor is used when set to [ON]. If the sensor breaks down, set to [OFF]. The sensor will not respond to any action and prizes are not counted when obtained. Even when set to ON and the sensor is broken, [Crime Prevention Mode] and [Prize Count (during customerstandby)] will not work.

DIP SW SETTINGS

DIP SW1 COIN SETTINGS

DIP_SW1 1 2 3 4 5 6 7 8

COIN 1P 1 COIN 1 CREDIT OFF OFF OFF OFF

2 COINS 1 CREDIT ON OFF OFF OFF

3 COINS 1 CREDIT OFF ON OFF OFF

4 COINS 1 CREDIT ON ON OFF OFF

5 COINS 1 CREDIT OFF OFF ON OFF

6 COINS 1 CREDIT ON OFF ON OFF

7 COINS 1 CREDIT OFF ON ON OFF

8 COINS 1 CREDIT ON ON ON OFF

9 COINS 1 CREDIT OFF OFF OFF ON

4 COINS 2 CREDITS ON OFF OFF ON

NOT USE

FREE PLAY ON ON ON ON

COIN 2P 1 COIN 1 CREDIT OFF OFF OFF OFF

2 COINS 1 CREDIT ON OFF OFF OFF

3 COINS 1 CREDIT OFF ON OFF OFF

4 COINS 1 CREDIT ON ON OFF OFF

5 COINS 1 CREDIT OFF OFF ON OFF

6 COINS 1 CREDIT ON OFF ON OFF

7 COINS 1 CREDIT OFF ON ON OFF

8 COINS 1 CREDIT ON ON ON OFF

9 COINS 1 CREDIT OFF OFF OFF ON

4 COINS 2 CREDITS ON OFF OFF ON

NOT USE

FREE PLAY ON ON ON ON

DIP SW2 SETTING COMMON GAME OPERATIONS FOR 1P AND 2P

NOTE: Set No. 7 and 8 switches to OFF.

DIP_SW2 1 2 3 4 5 6 7 8

BGM SOUND BGM1

OFF OFF

BGM2

ON OFF

BGM3 (Xmas)

OFF ON

OFF

ON ON

METER SETTINGS

TOTAL COIN (BILL=4COIN) /TOTAL PRIZE

OFF OFF

TOTAL COIN (25¢) /TOTAL BILL ($1)

ON OFF

1P PRIZE/2P PRIZE

OFF ON

1P BILL ($1) /2P BILL ($1)

ON ON

CRIME PREVENTION ON

OFF

MODE OFF

PRIZE COUNT OFF

OFF

(During customer-standby)

DIP SW SETTINGS

DIP SW3 (1P) DIP SW4 (2P) SETTING GAME OPERATIONS FOR 1P AND 2P SEPERATELY

DIP_SW3,4 1 2 3 4 5 6 7 8

PLAY TIME 15s OFF OFF OFF

20s ON OFF OFF

30s OFF ON OFF

40s ON ON OFF

50s OFF OFF ON

60s ON OFF ON

90s OFF ON ON

120s ON ON ON

GAME MODE NORMAL MODE (1 credit for 1 game) OFF

TIMER MODE (Games can be played any number of times during the time period)

DISPLAY MODE NORMAL GAME OFF

NO ACTIVITY (AND NO INITIALIZATION)

PRIZE SENSOR ON OFF

OFF ON

NOTE: Set No. 5and 6 switches to OFF.

ARM MECHANISM

ARM MECHANISM13

• Be careful not to damage the wires. Damaged wires may cause an electric shock, short circuit or present a risk of ﬁre.

• When securing plastic components, be careful not to tighten screws or nuts exces

sively. This may cause damage to the components. Fragments may also cause

injury.

• Before starting to manipulate the arm mechanism, cut off the power supply durng customer-standby status. Otherwise there could be malfunctions or damage.

13-1 ARM REPLACEMENT

To replace to arm L, enlarge the prize drop-out slot. (See Section 8) For the following procedures, an M3 slotted screwdriver is required.

1. Cut off the power supply in customer-standby status.

2. Use the operator’s key to open the glass door.

PHOTO 13-1a

4. Loosen the two screw shafts on the back of the UFO mechanism.

PHOTO 13-1b

SCREW SHAFT (2)

ARM MECHANISM

PHOTO 13-1e

PHOTO 13-1c

PHOTO 13-1d

FIG. 13-1

7. There are U-shaped notches on the mechanism mask. Slide the mechanism mask toward you and then remove it.

NOTE: For arm replacement on the opposite (left) side, slide the mask mechanism away from you and then

remove it. (Notch orientations are different)

5. Remove the UFO front cover

6. Use a slotted screwdriver to loosen the bolts that holds the arm in place.

UFO FRONT COVER

ARM BOLT

M3 x 6

U-SHAPED NOTCHES

MECHANISM MASK

ARM MECHANISM

PHOTO 13-1f

PHOTO 13-1g

11. The arm on the opposite (left) side can be replaced by following the same procedure.

NOTE: When attaching or removing the mechanism mask as indicated in steps 7 and 9, remember that the slide

direction is different. Slide the mechanism mask away from you to remove it; slide it toward you to attach it.

8. Remove the arm and attach the arm S or L replacement.

9. Refer to step 7 and reattach the mechanism mask. Pay special attention to the direction of the U-shaped notch when attaching.

10. Use a slotted screwdriver to tighten the bolt that

holds the arm in place (which had been loosened).

ARM BOLT

M3 x 6

ARM MECHANISM

13-2 ADJUSTMENT OF SENSOR BRACKET POSITION

When changing the arm size or to limit the range in which the UFO mechanism can move horizontally, change the position of the sensor bracket. The UFO mechanism stops where the sensor bracket is located. The sensor brackets are in a symmetrical spatial relationship with respect to 1P and 2P.

1. Loosen the wing screw and move the sensor bracket HP (Home Position) to the location indicated by the sticker.

PHOTO 13-2a

FIG. 13-2a

WING SCREW

STICKER

S ARMS

L ARMS

S ARMS

M ARMS

L ARMS

S ARMS

M ARMS

L ARMS

SENSOR BRACKET HP

When attaching arm L (2P):

When attaching arm M (2P):

When attaching arm S (2P):

STICKER

SENSOR BRACKET HP

STICKER

SENSOR BRACKET HP

STICKER

ARM MECHANISM

PHOTO 13-2b

PHOTO 13-2c

2. Tighten the wing screw.

3. Follow the above procedures to adjust the sensor bracket limit on the opposite side.

The sensor bracket limit positions and areas where the UFO mechanism cannot be moved to are as shown in the illustration.

FIG. 13-2b

WING SCREW

Areas where UFO mechanism cannot be mobved to.

SENSOR BRACKET HP

SENSOR BRACKET LIMIT

ARM MECHANISM

LIMITS ON FORWARD/BACKWARD MOVEMENT OF UFO MECHANISM

To limit the range in which the UFO mechanism can be moved forward/backward, change the position of the sensor bracket limit. The UFO mechanism stops where the sensor bracket limit is located.

PHOTO 13-2e

PHOTO 13-2f

1. Loosen the wing screw at the rear of the Y-oriented mechanism.

2. Move the sensor bracket limit to the desired location and tighten the wing screw.

The sensor bracket limit positions and areas where the UFO mechanism cannot be moved to are as shown in the illustration.

FIG. 13-2c

Y-ORIENTED MECHANISM

WING SCREW

SENSOR BRACKET LIMIT

Areas where UFO mechanism cannot be moved to.

SHOWCASE SHELF (EXAMPLE)

PRIZE FOR SHOWCASE (EXAMPLE)

ARM MECHANISM

13-3

SPRING STRENGTH ADJUSTMENT AND SPRING REPLACEMENT

Spring strength can be adjusted in three stages according to the position of the shift bracket. At a position close to the spring, the spring is weak (high level of difﬁculty). The farther the shift bracket is from the spring, the stronger becomes the spring (low level of difﬁculty). In addition, slight adjustments can be made with the POWER setting. (See Section 11-2.)

SPRING ADJUSTMENT

FIG. 13-3a

PHOTO 13-3a

1. Grasp the knob of the slide spring to loosen the connection with the shift bracket so that the spring can be moved to the right or left. Move the spring to the desired position.

2. Move the slide spring on the opposite side to the same position. (Establishes uniform strength on the right and left.)

When arm size has been replaced, even if the spring position on the shift bracket is the same, the arm gripping force (level of difﬁculty) will change.

The ﬁgure below shows arms of equivalent gripping force. Use it as a guide for setting level of difﬁculty.

Example) If the spring is at the rightmost position in the shift bracket when arm L is attached, and if the spring is at the leftmost position in the shift bracket when arm S is attached, arm gripping forces will be approximately equal.

FIG. 13-3b

Positon far from spring (low level of difficulty).

sition near the spring (high level of difficulty).

Intermediate position (intermediate level of difficulty).

SHIFT BRACKETSLIDE SPRING

When arm S is attached. When arm M is attached. When arm L is attached.

ARM MECHANISM

SPRING REPLACEMENT

PHOTO 13-3b

PHOTO 13-3c

1. Grasp the slide spring knob and remove the slide spring from the shift bracket.

2. Remove the slide spring from the spring bracket.

3. Attach a new slide spring.

4. Repeat the above procedure on the opposite side and replace.

Remove slide spring from spring bracket.

SLIDE SPRING

Remove slide spring from shift bracket.

UCS-3418

ARM MECHANISM

13-4 SHOVEL REPLACEMENT AND ADJUSTMENT

After shovels have been replaced, conﬁrm during initialization that the shovels do not overlap each other when the arm is closed.

IMPORTANT

FIG. 13-4

Select a shovel in accordance to the prizes being used. Remove the two ﬂat head screws and replace shovel.

1. Loosen the two wing screws.

2. Turn the adjustment screw to adjust the distance between shovels.

3. After adjusting so the shovels do not overlap, tighten the two loosened wing screws.

PHOTO 13-4

SHOVEL OVERLAP ADJUSTMENT

Confirm that shovels do not overlap each other.

SHOVEL W30 EG-3405Y

SHOVEL W60 EG-3404

SHOVEL W40

MKW-2120

FLAT HEAD SCREW (2)

M3 x 5

Adjust.Adjust.ADJUSTMENT SCREW

WING SCREW

ARM MECHANISM

13-5 OPEN ARM ANGLE ADJUSTMENT

In cases such as when the arm comes in contact with the UFO cover, the open arm angle should be adjusted. For the following procedures, an M3 Philips screwdriver or a screwdriver/spanner for M3 hexagonal nuts is required.

PHOTO 13-5a

PHOTO 13-5b

1. Loosen the two screws. Hold the arm mechanism at this time so it will not fall.

2. Remove the arm mechanism. Be especially careful when removing, as there are connections.

PHOTO 13-5c

3. Loosen the two ﬂange nuts.

5. Tighten the ﬂange nuts and follow the above procedure in reverse order to attach the arm mechanism. Be sure to conﬁrm at this time that no wiring has been caught.

PHOTO 13-5d

4. Slide the sensor bracket arm laterally to adjust the open arm angle. When the arm is slid to side A, the open arm angle becomes large. When the arm is slid to side B, the angle becomes small.

M3 x 8, with flat & spring washers

SCREW (2)

ARM MECHANISM

FLANGE NUT (2)

MAINTENANCE OF Z-ORIENTED MECHANISM

MAINTENANCE OF Z-ORIENTED MECHANISM14

• Be careful not to damage the wires. Damaged wires may cause an electric shock, short circuit or present a risk of ﬁre.

• Use only prescribed grease. Using other types of grease could cause damage to components.

• Apply grease only to prescribed locations. Otherwise, operations may become defective and component materials may be altered.

IMPORTANT

An M4 Philips screwdriver is required for the following procedure.

APPLYING GREASE TO INTERIOR OF Z-ORIENTED MECHANISM

Apply grease to the following areas once every three months. For spray grease, use grease mate (PART No. 090-0066).

PHOTO 14a

1. Remove the two connectors.

PHOTO 14b

2. Remove the two truss screws on the back side.

Remove connector.

TRUSS SCREW (2), chrome

M4 x 8

MAINTENANCE OF Z-ORIENTED MECHANISM

PHOTO 14c

3. Loosen the two truss screws on the front side.

PHOTO 14d

4. Remove the Z-oriented mechanism.

5. Insert spray grease nozzle into the hole for greasing and apply grease.

6. Carry out the above procedures in reverse order to reattach the mechanism. Be sure to conﬁrm at this time that no wiring has been caught.

PHOTO 14e

M4 x 8

TRUSS SCREW (2), chrome

Z-ORIENTED MECHANISM

HOLE FOR GREASING

COIN SELECTOR

COIN SELECTOR15

15-1 REMOVING THE COIN SELECTOR

PHOTO 15-1a

1. Turn the power off.

2. Unlock with the operator’s key and open the service door.

PHOTO 15-1b

3. Loosen the thumbscrew on the back of the coin selector.

PHOTO 15-1c

4. Push up the stopper that holds the coin selector in place.

• Be careful not to damage the wires. Damaged wires may cause an electric shock, short circuit or present a risk of ﬁre.

STOPPER

Loosen thumbscrew.

COIN SELECTOR

PHOTO 15-1fPHOTO 15-1e

PHOTO 15-1d

5. Open the back hold cover.

6. While paying attention to the lockout lever, slide the coin selector slightly to the right, then remove it by pulling it forward.

15-2 REMOVING A JAMMED COIN

When the coin return button fails to refund coins, open the service door and open the selector gate. Once the jammed coin is removed, insert a standard coin to ensure that the selector is working properly.

BACK HOLD COVER

LOCKOUT LEVER

COIN SELECTOR

15-3 CLEANING THE COIN SELECTOR

The coin selector should be cleaned once every 3 months. When cleaning, follow the procedures below:

Fig. 15-3a

1. Open the gate and remove dust using a soft brush (made of wool, etc.).

2. Remove and clean smears by using a soft cloth dipped in water or diluted chemical detergent and then wrung dry.

3. Remove the cradle. When detaching the retaining ring (E ring), be extra careful not to bend the rotational axis.

4. Use a soft cloth to wipe any dirt/debris off the rotational axis and bearings.

5. After wiping as described in the previous step, use a dry cloth, etc. to dry the coin selector completely.

Fig. 15-3b

15-4 COIN INSERTION TEST

Carry out a coin insertion test once per month. At the same time, check the following points:

□ Does the Coin Meter count properly? □ Do coins drop into the Cashbox correctly? □ Are coins rejected when inserted while holding down the Reject Button?

IMPORTANT

• Remove and clean smears using a soft cloth dipped in water or diluted chemical

detergent and then wrung dry.

• Never apply machine oil, etc. to the coin selector.

• After cleaning the coin selector, properly insert a standard coin to ensure that the

selector functions correctly.

GATE

CRADLE

REPLACEMENT OF FLUORESCENT LIGHTING, LAMPS, AND FUSES

16-1 FLUORESCENT LIGHTING REPLACEMENT

Replacement of Fluorescent Ceiling Lamps

FIG. 16-1

Remove ﬂuorescent ceiling lamps by pushing them toward the right and replace.

Replacement of Fluorescent Lamps on Sides

The work must only be carried out by personnel with electrical appliance knowledge. Shocks and other serious accidents may result if the work is carried out by unqualiﬁed individuals.

• Use lamps of the speciﬁed ratings. Using lamps with different ratings may cause ﬁres or damage.

• You may get burned by a hot ﬂuorescent lamp or other lamps. Pay full attention to the lamps when performing the work.

• There is the danger of accidents involving electrical shorts circuits or ﬁre caused by factors such as the deterioration of insulation in lighting equipment over time. Check that there are no anomalies such as the following: odors from burning, socket discoloration, frequent lamp replacements.

FLUORESCENT LAMP (F32T8) 390-6839-32

FLUORESCENT LAMP (F25T8) 390-6839-25

REPLACEMENT OF FLUORESCENT LIGHTING, LAMPS, AND FUSES

1. Turn the power off.

2. Loosen the two screws and remove the switch cover. Hold the switch cover (L) while removing so it will not fall.

16-2 LAMP REPLACEMENT

Replacement of Down Button Lamp

The provided tamperproof wrench is required for the following procedures.

1. Turn the power off.

PHOTO 16-2a

2. Remove the 7 tamperproof screws, then remove the control panel.

• Be careful not to damage the wires. Damaged wires may cause an electric shock, short circuit or present a risk of ﬁre.

• When ﬁxing the plastic parts, do not fasten the screws and nuts too tightly. Failure to observe this instruction may damage these parts and as a result the broken pieces of these parts may cause a person injury.

3. Remove ﬂuorescent lamps by pushing them upward and replace. (See FIG. 16-1.)

SCREW (2) M4 x 8, with flat & spring washers

SWITCH COVER (L) [Opposite side: SWITCH COVER (R)]

TAMPERPROOF SCREW (7), chrome

M4 x 16

PHOTO 16-1

REPLACEMENT OF FLUORESCENT LIGHTING, LAMPS, AND FUSES

PHOTO 16-2b

3. Hold the switch component between your ﬁngers and remove it from the button base. Be careful not to damage wiring connected to the switch.

PHOTO 16-2c

4. There is a lamp at the tip of the switch component. Pull the lamp out straight without turning it.

5. Attach the connector so that it goes to the right side and return the control panel to its original position.

PHOTO 16-2ePHOTO 16-2d

WEDGE-BASE LAMP 14V, 3.4W

REPLACEMENT OF FLUORESCENT LIGHTING, LAMPS, AND FUSES

Selector Button Lamp Replacement

PHOTO 16-2f

1. Turn the power off.

2. Unlock with the operator’s key and open the service door.

PHOTO 16-2g

3. Pull the lamp out straight to replace it.

WEDGE-BASE LAMP 12V, 2.2W

REPLACEMENT OF FLUORESCENT LIGHTING, LAMPS, AND FUSES

The provided tamperproof wrench is required for the following procedures.

1. Turn the power off.

PHOTO 16-3a

2. Remove the 2 tamperproof screws, unlock with the master key and open the back lid.

3. The 2 fuses are located at the back of the left side. When replacing them, make sure that the ratings are correct.

16-3 FUSE REPLACEMENT

• The work must only be carried out by personnel with electrical appliance knowledge. Shocks and other serious accidents may result if the work is carried out by unqualiﬁed individuals.

• After eliminating the cause of a blown fuse, replace the fuse. Depending on the cause of the fuse blow, continued use with the blown fuse may cause the generation of heat and present a risk of ﬁre.

• Be sure to use fuses of the speciﬁed rating. Using fuses exceeding the speciﬁed rating may cause ﬁre or electric shock.

PHOTO 16-3cPHOTO 16-3b

FUSE (LOWER)

250V, T, 2A

FUSE (UPPER) 250V, T, 5A

TAMPERPROOF SCREW (2), chrome

BACK LID

M4 x 8

PERIODIC INSPECTION

PERIODIC INSPECTION17

The items listed below require periodic check and maintenance to retain the performance of this machine and to ensure safe business operation.

ITEMS DESCRIPTION PERIOD REFERENCE

CABINET

Check that adjustors in contact with ﬂoor

Daily See Section 3

GEAR COMPONENTS Apply Grease 3 months See Section 13

FLUORESCENT LIGHTING Inspection of Lighting Equipment As necessary See Section 16

COIN SELECTOR

Coin Insertion Test Monthly See Section 15

Cleaning Tri-monthly See Section 15

GLASS DOOR Cleaning As necessary See below.

CABINET SURFACES Cleaning As necessary See below.

ELECTRICAL/ELECTRONIC COMPONENTS

Inspection As necessary See above.

INTERIOR Cleaning Annually See above.

POWER SUPPLY PLUG Inspection and Cleaning Annually See above.

TABLE 17 PERIODIC INSPECTION TABLE

When the cabinet surfaces become dirty, remove stains with a soft cloth soaked in water or diluted (with water) chemical detergent and then wrung dry. To avoid damaging the ﬁnish, do not use such solvents as thinner, benzene, etc. (other than ethyl alcohol) or abrasives (bleaching agent and chemical dust-cloth). Some general-purpose household, kitchen, and furniture cleaning products may contain strong solvents that degrade plastic components, coatings, and print. Before using any cleaning product, read the product's cautionary notes carefully and test the product ﬁrst on a small area that is not highly visible.

Cleaning the Glass Door

The glass door can easily become dirty so be sure to clean it often. Use regular glass cleaners and wipe both glass surfaces. If you are using a spray glass cleaner, be sure to wipe away cleaner left on surrounding non-glass areas.

• Be sure to check once a year to see whether Power Cords are damaged, the plug is securely inserted, dust has accumulated between the Socket Outlet and the Power Plug, etc. Using the product with accumulated dust can cause ﬁre and electric shock.

• Never use a water jet, etc. to clean inside and outside the cabinet. If the machine gets wet for any reason, do not use it until it has completely dried.

• Periodically, around once a year, get in touch with the place of contact herein stated or the Distributor, etc. where the product was purchased from, regarding internal cleaning. Using the product with accumulated dust in the interior can cause a ﬁre or accident. Note that professional cleaning will require a fee.

• There is the danger of accidents involving electrical shorts circuits or ﬁre caused by factors such as the deterioration of insulation in electrical and electronic equipment over time. Check that there are no anomalies such as odors from burning.

Cleaning the Cabinet Surfaces

ERROR MESSAGES

ERROR MESSAGES 18

When an error occurs in the mechanism, a number corresponding to the error is displayed on the 7-seg displays on the side (1P or 2P) that the error has occurred. Press the test switch to enter test mode.

Test the mechanism and conﬁrm the location of the error before exiting test mode. After initialization, credits attained before the error are restored and the game resumes. (Partial credits attained for multiple coins are deleted). For details, see [11-3 Explanation of Test Mode]. When an error has occurred, the credits are displayed in 2 digits on the small 7-seg displays.

If an error of unknown cause occurs and cannot be resolved, or if the same error occurs frequently, turn the power off and contact the ofﬁce indicated on these instructions or where the product was purchased.

No.

7-seg Display

Reads Cause

0 00E BACK limit sensor in the X-direction does not turn ON.

1 01E BACK limit sensor in the X-direction does not turn OFF.

2 02E FWD limit sensor in the X-direction does not turn ON.

3 03E FWD limit sensor in the X-direction does not turn OFF.

Corrective Measure: Errors involving left/right movements. Check the limit sensor and its operation in test

mode 1. (See Section 11)

4 04E BACK limit sensor in the Y-direction does not turn ON.

5 05E BACK limit sensor in the Y-direction does not turn OFF.

6 06E FWD limit sensor in the Y-direction does not turn ON.

7 07E FWD limit sensor in the Y-direction does not turn OFF.

Corrective Measure: Errors involving forward/backward movements. Check the limit sensor and its operation in

test mode 1. (See Section 11)

8 08E UP limit sensor in the Z-direction does not turn ON.

9 09E UP limit sensor in the Z-direction does not turn OFF.

10 10E DOWN limit sensor in the Z-direction does not turn ON.

11 11E DOWN limit sensor in the Z-direction does not turn OFF.

Corrective Measure: Errors involving up/down movements. Check the limit sensor and its operation in test

mode 2. (See Section 11)

12 12E Open sensor does not turn ON.

13 13E Open sensor does not turn OFF.

Corrective Measure: Errors involving open/close movements. Check the open sensor and its operation in test

mode 3. (See Section 11)

14 14E There is no coin meter attached.

Corrective Measure: Errors involving the coin meter. Check the meter, its operation, and wire connections.

15 15E Problem with the prize sensor.

Corrective Measure: Errors involving the prize sensor. Check the prize sensor and its operation in test mode.

(See Section 11)

20 Problem with the X-axis.

Corrective Measure: Errors involving the X-axis. Check the limit sensor and its operation in test mode 1.

21 Problem with the Y-axis.

Corrective Measure: Errors involving the Y-axis. Check the limit sensor and its operation in test mode 1.

If the following errors occur after the power supply has been activated, there may be a problem with the DIP SW board.

TABLE 18

TROUBLESHOOTING

TROUBLESHOOTING19

The items listed below require periodic check and maintenance to retain the performance of this machine and to ensure safe business operation.

CIRCUIT PROTECTOR

FIG. 19b

The Circuit Protector uses a bimetal to break the circuit. Due to the heat, the machine cannot be restarted until it cools. Wait at least 1 minute before restarting. (Press the button in.)

• In order to prevent electric shock and short circuit, be sure to turn the power off and unplug the electrical cord from the outlet before working on the machine.

• Be careful not to damage wiring. Damaged wiring may cause electric shock or short circuit.

• After ﬁxing the problems regarding the Circuit Protector, reinstate the Circuit Protector. Depending on the cause of the problem, using the Circuit Protector without addressing the malfunction can generate heat and can present a ﬁre hazard.

FIG. 19a

CIRCUIT PROTECTOR

YES

OFF

Problem has occurred.

Dose the fluorescent

lighting turn on?

Is the fuse okay?

Is the machine in

display mode?

Is there an error

displayed?

Can a game be played?

Is the POWER LED

on the GAME BD lit?

Go to error correction.

Go to fuse replacement.

Check DIP SW.

Are LEDs 1 and 2

on the GAME BD lit?

No power is going

to the GAME BD.

Turn off power supply SW.

There could be defective

wiring or disconnection.

The GAME BD is

operating.

The GAME BD is

not operating

properly.

Are the glass doors

closed?

Are the power supply

switches ON?

Is the circuit

protector ON?

Check the power cord.

AC 120V is not being supplied.

Either the wiring is

defective or the flourescent

light has burnt out.

Close the glass doors on

the left and right securely.

Turn the power supply

switches in both

locations to ON.

Turn the protector to

ON. (See Fig.6-4a)

Insert cord into

outlet/inlet properly.

Flashing or out.

YES

GOOD

YES

GOOD

YES

DESIGN-RELATED PARTS

DESIGN-RELATED PARTS20

For the Warning Display Stickers, refer to Section1.

FIG. 20a Basic Cabinet

FIG. 20b Full Options Cabinet (See Section 21.)

FL GLASS SHEET

UCU-1032

(The opposite side is the same.)

CTRL PNL SHEET UCU-2002

DESIGN SHEET UCU UCU-3401 (The opposite side is the same.)

LCD COVER PLATE

UCU-0021

STICKER LEFT UCU-1002-B

STICKER FRONT A UCU-1002-D

STICKER FLAP UCU-1342 (The opposite side is the same.)

STICKER RIGHT UCU-1002-C

STICKER FRONT C UCU-1002-F

STICKER FRONT B UCU-1002-E

BILLBOARD RIGHT

UCU-0014

(Opposite side)

BILLBOARD LEFT

UCU-0013

BILLBOARD FRONT UCU-0012

STICKER SERVICE DOOR UCU-1062

BILLBOARD FRONT UCU-0012

FL GLASS SHEET UCU-1032

(The opposite side is the same.)

CTRL PNL SHEET UCU-2002

DESIGN SHEET UCU

UCU-3401 (The opposite side is the same.)

STICKER BACK BOARD

UCU-0041

STICKER LEFT UCU-1002-B

STICKER FRONT A UCU-1002-D

STICKER FLAP

UCU-1342 (The opposite side is the same.)

STICKER RIGHT UCU-1002-C

STICKER FRONT C UCU-1002-F

STICKER SERVICE DOOR UCU-1062

STICKER FRONT B UCU-1002-E

BILLBOARD RIGHT UCU-0014

(Opposite side)

BILLBOARD LEFT UCU-0013

OPTIONAL ITEMS

OPTIONAL ITEMS21

The following optional items are available for the SEGA UFO CATCHER.

- Dollar Bill Validator: 2 sets

- Security Bar Coin Security Bar: 1 set Bill Security Bar: 2 sets

- LCD Unit LCD Case + Cable Cover: 1 set LCD Monitor: 1 set Movie Player: 1 set

21-1 DOLLAR BILL VALIDATOR

DOLLAR BILL VALIDATOR INSTALLATION

Be sure to use the “AE2432D5” dollar bill validator made by MEI.

IMPORTANT

Install the dollar bill validators on the 2 bill validator doors on the left and right of the cabinet front panel.

PHOTO 21-1a

1. Turn the power off.

2. Unlock with key and open the bill validator door.

• The work must only be carried out by personnel with electrical appliance knowledge. Shocks and other serious accidents may result if the work is carried out by unqualiﬁed individuals.

• Be careful not to damage the wires. Damaged wires may cause an electric shock, short circuit or present a risk of ﬁre.

BILL VALIDATOR DOOR

OPTIONAL ITEMS

PHOTO 21-1b

3. Remove the 4 ﬂange nuts, then remove the blind plate.

PHOTO 21-1c

4. Attach the dollar bill validator with the 4 ﬂange nuts that were removed.

PHOTO 21-1d

5. Connect the one connector.

NOTE: The photos show installation on the cabinet left side. Install the bill validator on the right side in the same

manner.

BLIND PLATE

FLANGE NUT (4) M4

OPTIONAL ITEMS

DIP SWITCH SETTINGS

1. Set the DIP SWITCHES for use as illustrated below.

PHOTO 21-1e

NOTE: For details on bill validator handling, inspection, changing settings, etc., refer to the sticker attached or the

[Bill Acceptor (Validator) “Installation Guide”] provided with the bill validator.

1 free 2 free 3 free 4 ON 5 OFF 6 OFF 7 OFF 8 ON

The following types of security bars are available.

- Coin Security Bar: 1 set

- Bill Security Bar: 2 sets

21-2 SECURITY BAR

COIN SECURITY BAR INSTALLATION

PHOTO 21-2b

PHOTO 21-2a

PHOTO 21-2c

1. Turn the power off.

2. Unlock with key and open the right bill validator door.

DIP SW

BILL SECURITY BAR (2 sets)

COIN SECURITY BAR (1 set)

BILL VALIDATOR DOOR

OPTIONAL ITEMS

PHOTO 21-2d

3. Remove the 3 ﬂange nuts on the inside of the bill validator door, then remove the 3 carriage bolts from the cabinet front side. Be careful not to drop or lose the ﬂange nuts.

PHOTO 21-2e

4. Set the coin security hook on the cabinet and secure it in place with the 3 ﬂange nuts that were removed.

5. Unlock with key and open the left bill validator door.

PHOTO 21-2f

6. Remove the 3 ﬂange nuts on the inside of the bill validator door, then remove the 3 carriage bolts from the cabinet front side. Be careful not to drop or lose the ﬂange nuts.

CARRIGAGE BOLT (3), chrome

M6 x 20

FLANGE NUT (3) M6 (Inside)

COIN SECURITY HOOK

CARRIGAGE BOLT (3), chrome

M6 x 20

FLANGE NUT (3)

M6 (Inside)

OPTIONAL ITEMS

PHOTO 21-2g

7. Set the spacer in the coin security bar and secure it in place on the cabinet with the 3 ﬂange nuts that were removed.

8. Close both the left and right service doors.

BILL SECURITY BAR INSTALLATION

PHOTO 21-2i

1. Turn the power off.

2. Unlock with key and open the left bill validator door.

PHOTO 21-2j

3. Remove the 3 ﬂange nuts on the inside of the bill validator door, then remove the 3 carriage bolts from the cabinet front side. Be careful not to drop or lose the ﬂange nuts.

PHOTO 21-2h

PHOTO 21-2j PHOTO 21-2k

CARRIGAGE BOLT (3), chrome

M6 x 20

FLANGE NUT (3)

M6 (Inside)

SPACER

COIN SECURITY BAR SPACER

OPTIONAL ITEMS

PHOTO 21-2l

4. Set the bill security hook on the cabinet and secure it in place with the 3 ﬂange nuts that were removed.

PHOTO 21-2m

5. Unlock the glass door with the operator’s key and open it.

PHOTO 21-2o

6. Remove the 2 ﬂange nuts inside the cabinet, then remove the 2 carriage bolts from the cabinet front side.

PHOTO 21-2n

BILL SECURITY HOOK

OPERATOR'S KEY

FLANGE NUT (2)

CARRIGAGE BOLT (2), chrome M6 x 20

FLANGE NUT (2) (Opposite side) M6

OPTIONAL ITEMS

PHOTO 21-2p

7. Close the left bill validator door.

8. Set the bill security bar on the cabinet and secure it in place with the 2 ﬂange nuts that were removed.

NOTE: Follow the same procedure to install the bill security bar on the right side. There are no differences in

procedure for the left and right sides.

21-3 LCD UNIT (LCD CASE + CABLE COVER)

LCD UNIT ASSEMBLY

Always use an LCD monitor provided by SEGA.

IMPORTANT

PHOTO 21-3a

1. Assemble the LCD case and cable cover with the 4 screws.

2. Remove the 4 ﬂange nuts, then remove the LCD bracket

PHOTO 21-3b

SCREW (4)

LCD CASE

CABLE COVER

M4 x 8, with flat & spring washers

FLANGE NUT (4) M4

OPTIONAL ITEMS

3. Remove the LCD monitor stand, then connect the RGB cables and the power cable.

PHOTO 21-3c

NOTE: The LCD monitor may differ from the one shown

in the photo.

4. Use the 4 truss screws to attach the LCD bracket to the monitor.

(Attach the LCD bracket so that the wooden area held down by two points is on the upper side.)

PHOTO 21-3ePHOTO 21-3d

5. Return the LCD bracket with monitor attached to the LCD case and secure it in place with the 4 ﬂange nuts

removed in step 2. Be careful not to damage the cables.

PHOTO 21-3gPHOTO 21-3f

RGB CABLE

POWER CABLE

TURSS SCREW (4) M4 x 15

OPTIONAL ITEMS

6. Bundle the cables and secure them in place with a cable tie. In bundling the cables, leave enough space for connectors to be connected to each unit.

PHOTO 21-3h

7. Turn the unit over and use the master key to open LCD unit door.

PHOTO 21-3i

8. Use double-sided tape to secure the movie player to the inside surface of the LCD unit door, then connect the RGB cables and AC adaptor cable. Connect the RGB cables and AC adaptor cable as shown in the illustration.

PHOTO 21-3jFIG. 21-3a

NOTES:

- Tune the monitor before assembly. After attaching the monitor to the inside panel, the tuning button becomes hidden, and tuning may become difﬁcult.

- The movie player may differ from the one shown in the photo.

- For details on the handling of the LCD monitor or the movie player, refer to the instruction manual provided with each unit.

LCD UNIT DOOR

MOVIE PLAYER

AC ADAPTOR CABLE

RGB CABLE

LCD

MONITOR

MOVIE PLAYER

RGB IN

AC ADAPTOR CABLE

RGB OUT

POWER IN

AC 120V

RGB CABLE

OPTIONAL ITEMS

INSTALLATION OF LCD UNIT ON CABINET

1. Remove the 2 truss screws from inside the cabinet.

PHOTO 21-3k

2. Remove the 2 tamperproof screws on the left and right of the cabinet rear panel.

PHOTO 21-3l

3. Remove the 1 tamperproof screw in the center, then remove backboard B.

Hold backboard B at this time so it will not fall while working.

PHOTO 21-3m

TRUSS SCREW (2), chrome M4 x 8

TAMPERPROOF SCREW (2), chrome M4 x 8

BACKBOARD B

TAMPERPROOF SCREW (1), chrome M4 x 8

OPTIONAL ITEMS

4. Remove the backboard upper bracket from backboard B.

PHOTO 21-3n

5. Use the 2 provided truss screws to install the LCD unit hook to the backboard upper bracket.

PHOTO 21-3o

6. Attach the LCD unit hook to backboard A (the side with no sticker should face the outer side of the cabinet).

PHOTO 21-3p

TRUSS SCREW (2),chrome

LCD UNIT HOOK

M4 x 8

LCD UNIT HOOK

BACKBOARD A

BACKBOARD UPPER BRACKET

BACKBOARD B

OPTIONAL ITEMS

7. Load backboard A onto the cabinet rear panel, then secure it in place by reversing the steps used to remove the truss screw in the center and the 2 tamperproof screws on the left and right from backboard B. Hold backboard A at this time so it will not fall while working.

8. Secure in place with 2 truss screws from inside the cabinet.

PHOTO 21-3rPHOTO 21-3q

9. Suspend the LCD unit on the LCD hooks. Have 2 people do this job, as the assembled LCD unit weighs over 15 kg.

PHOTO 21-3s

10. Use the 4 truss screws provided to secure the LCD

cover to the inside of the cabinet. Make sure that the LCD cover does not fall while working.

PHOTO 21-3t

LCD HOOK

TRUSS SCREW (4) M4 x 20, flat washer used

OPTIONAL ITEMS

11. Remove the 2 tamperproof screws, unlock with the master key and open the back lid.

PHOTO 21-3vPHOTO 21-3u

12. Secure the LCD unit with 2 screws from the inside of the cabinet.

PHOTO 21-3w

PHOTO 21-3yPHOTO 21-3x

13. Close the back lid and lock.

BACK LID

TAMPERPROOF SCREW (2), chrome M4 x 8

SCREW (2) M4 x 8, with flat & spring washers

PARTS LIST

PARTS LIST22

(3) ASSY SUB CABINET

(UCU-1001)

(6) ASSY SPEAKER

(UCS-1050X)

(7) ASSY SERVICE DOOR

(UCU-1060)

(8) SW UNIT

(UCU-1070)

(9) AC UNIT

(UCU-1080)

(10) ASSY PRIZE SENSOR

(USS-1200)

(11) ASSY FL BASE L

(UCU-1300)

(12) ASSY FL BASE R

(UCU-1310)

(13) SIDE FL UNIT

(UCU-1320)

(14) FLAP UNIT

(UCU-1340)

(20) ASSY X MECHA

(UCU-3050)

(20) ASSY X MECHA

(UCU-3050)

(26) ASSY ARM MECHA

(UCU-3410)

(27) ASSY REAR COVER

(UCS-3450)

(1) TOP ASSY UCU

(UCU-0000)

(2) ASSY CABINET

(UCU-1000)

(15) ASSY GLASS DOOR L

(UCU-1100)

(16) ASSY GLASS DOOR R

(UCU-1110)

(17) ASSY BACK LID

(UCU-1150)

(18) ASSY CTRL PNL PLATE

(UCU-2000)

(19) ASSY X MECHA 1P

(UCU-3000)

(21) ASSY X MECHA 2P

(UCU-3010)

(22) ASSY Y MECHA

(UCU-3100)

(23) ASSY Z MECHA

(UCU-3200)

(24) ASSY PIPE

(UCU-3300)

(25) ASSY UFO MECHA

(UCU-3400)

(28) ASSY MAIN BD

(UCU-4000)

(4) CABINET

(UCU-1002)

(5) ASSY WIRE

(UCU-6001)

PARTS LIST

(1) TOP ASSY UCU (UCU-0000)

(D-1/2)

(Earth terminal)

Position for affixing

(Opposite side)

Details of part "B"

(NOT TO SCALE)

Left/right height is

647.5 +/-2 mm

In affixing (62) in the left/right direction, use the center

as a point of reference. The tolerance is +/-2mm.

PARTS LIST

ITEM NO. PART NO. DESCRIPTION NOTE

1 UCU-1000 ASSY CABINET 2 UCU-1100 ASSY GLASS DOOR L 3 UCU-1110 ASSY GLASS DOOR R 4 UCU-1150 ASSY BACK LID 5 UCU-2000 ASSY CTRL PNL PLATE 6 UCU-3000 ASSY X MECHA 1P 7 UCU-3010 ASSY X MECHA 2P 8 UCU-3100 ASSY Y MECHA 9 UCU-3200 ASSY Z MECHA 10 UCU-3300 ASSY PIPE 11 UCU-3400 ASSY UFO MECHA 12 UCU-4000 ASSY MAIN BD 13 UCU-0001 SIDE GLASS 14 UCU-0002 SIDE GLASS SASH A 15 UCU-0003 SIDE GLASS SASH B L 16 UCU-0004 SIDE GLASS SASH B R 17 UCU-0005 SHIPPING BRKT TOP 18 UCU-0006 SHIPPING CENTER BAR 19 UCS-0007 SHIPPING BRKT MECHA 20 UCU-0007 GLASS EDGE GUARD A 21 UCU-0008 GLASS EDGE GUARD B 22 UCU-0009 FL COVER PLATE 23 UCU-0010 SW COVER L 24 UCU-0011 SW COVER R 25 UCU-0012 BILLBOARD FRONT 26 UCU-0013 BILLBOARD LEFT 27 UCU-0014 BILLBOARD RIGHT 28 UCU-0015 BILLBOARD WASHER 29 UCU-0016 BILL VALIDATOR DOOR 30 UCU-0017 BILL DOOR CUSSION 31 UCU-0042 BLIND PLATE 32 DP-1148X LKG TNG 33 UCU-0018 BACK BD UPPER BRKT 37 421-11416 STICKER CAUTION FORK 38 421-8479-01 STICKER INSTR SUNLIGHT ENG 39 421-7974-01 STICKER CAUTION GLASS ENG 41 421-6690-01 STICKER 120V 42 440-WS0002XEG STICKER W POWER OFF ENG 43 440-WS0286-EG STICKER W DO NOT OPEN ENG 47 440-WS0027-EG STICKER W HIGH TEMP WIDE ENG 48 421-12116 STICKER BILL VALIDATOR 49 UCU-1002-B STICKER LEFT 50 UCU-1002-C STICKER RIGHT 51 UCU-1002-D STICKER FRONT A 52 UCU-1002-E STICKER FRONT B 53 UCU-1002-F STICKER FRONT C 54 621-000110-US PACKING SET UCU-0000 57 421-6119-91 STICKER FCC 58 440-CS0316-EG STICKER C PRIZEDOOR ENG 61 UCU-0040 BACK BOARD B 62 UCU-0041 STICKER BACK BOARD

(D-2/2)

101 220-5794 CLY LOCK W/KEYS 102 390-6836-32 FL FO32/841/XP/ECO SYLVANIA 103 390-6836-25 FL FO25/841/XP/ECO SYLVANIA 104 280-5275-SR10 CORD CLAMP SR10 105 601-0460 PLASTIC TIE BELT 100 M/M 106 280-5124-04 NYLON CLAMP NK04

201 000-P00408-W M SCR PH W/FS M4x8 202 000-T00408-0C M SCR TH CRM M4x8 203 008-T00408-0C TMP PRF SCR TH CRM M4x8 204 008-T00412-0C TMP PRF SCR TH CRM M4x12 206 000-P00425-S M SCR PH W/S M4x25 207 050-F00400 FLG NUT M4 208 068-441616-0C FLT WSHR CRM 4.4-16x1.6 209 068-552016-0C FLT WSHR CRM 5.5-20x1.6 210 000-P00406-0C M SCR PH CRM M4x6 211 000-P00410-0C M SCR PH CRM M4x10 212 000-P00410-W M SCR PH W/FS M4x10 213 020-000410-0Z HEX SKT H CAP SCR BLK 0Z M4x10 214 060-F00400 FLT WSHR M4 215 060-S00400 SPR WSHR M4 216 FAS-600004 SPR WSHR CRM M4 217 050-F00600 FLG NUT M6 218 031-000620-0C CRG BLT CRM M6x20 219 008-T00416-0C TMP PRF SCR TH CRM M4x16

301 UCU-60016 WH BILLVALIDATOR 302 UCU-60026 WH EARTH BILL

401 601-6604-70 CARTON BOX 70 403 420-6953 OWNERS MANUAL UCU ENG 404 UCS-3430 ARM S 405 UCS-3432 ARM L 406 EG-3404 SHOVEL W60 407 MKW-2120 SHOVEL W40 408 EG-3405Y SHOVEL W30 409 600-7326 AC CABLE CONNECT TYPE USA 15A 410 220-5793-2-A001 KEY MASTER A001 411 220-5793-2-A002 KEY MASTER A002 413 540-0006-01 WRENCH M4 TMP SCR 414 USS-3418 SLIDE SPRING 415 000-T00408-0C M SCR TH CRM M4x8

PARTS LIST

(2) ASSY CABINET (UCU-1000)

(D-1/2)

When assembling (13), be sure to insert (105).

[The (105) disk plate should be above (13)]

(Including opposite side)

(Earth

terminal)

4 pieces

Have the granulated

surface face upward.

Arrange the position of

the convex part to the C

beveling side.

Detailed drawings for installation of

(13) and (105). (NOT TO SCALE)

PARTS LIST

ITEM NO. PART NO. DESCRIPTION NOTE

1 UCU-1001 ASSY SUB CABINET 2 UCS-1050X ASSY SPEAKER 3 UCU-1060 ASSY SERVICE DOOR 4 UCU-1070 SW UNIT 5 UCU-1080 AC UNIT 6 USS-1200 ASSY PRIZE SENSOR 7 UCU-1300 ASSY FL BASE L 8 UCU-1310 ASSY FL BASE R 9 UCU-1320 SIDE FL UNIT 10 UCU-1340 FLAP UNIT 11 839-1276R CREDIT BD US 12 UCU-1003 CTRL PNL COVER 13 UCU-1004 LEVER BRKT 14 UCU-1005 CASH BOX DOOR 15 DP-1148X LKG TNG 16 UCU-1006 FIELD PLATE L 17 UCU-1007 FIELD PLATE R 18 UCU-1008 CHUTE ADJUST PLATE L 19 UCU-1009 CHUTE ADJUST PLATE R 20 UCU-1010 PARTITION HOLDER L 21 UCU-1011 PARTITION HOLDER R 22 UCU-1012 CORNER PARTITION L 23 UCU-1013 CORNER PARTITION R 24 UCU-1014 FIX PARTITION 25 UCU-1015 PARTITION BRKT CL 26 UCU-1016 PARTITION CL 27 UCU-1017 PARTITION FRONT 28 UCU-1018 PARTITION BRKT FRONT 29 UCU-1019 SPEAKER COVER 30 UCU-1020 WIRE COVER 31 UCU-1021 PRIZE SENSOR COVER L 32 UCU-1022 PRIZE SENSOR COVER R 33 253-5366 CASH BOX 34 421-12106-01 STICKER BULB 3.8W14V UL

101 220-5794 CLY LOCK W/KEYS 102 560-5530-V XFMR100-120V100V2A24V5A WB UL 103 601-11480-8 PLAPOINT L=8 104 601-11480-20 PLAPOINT L=20 105 509-6121-01 JOYSTICK 8WAY 50-6070-10(HAPP) 106 280-6581-29 BUSHING NB-29

201 000-P00308-W M SCR PH W/FS M3x8 202 000-P00408-W M SCR PH W/FS M4x8 203 000-T00408-0C M SCR TH CRM M4x8 204 000-T00416-0C M SCR TH CRM M4x16 205 008-T00408-0C TMP PRF SCR TH CRM M4x8 206 050-F00400 FLG NUT M4 207 050-F00500 FLG NUT M5 208 068-441616-0C FLT WSHR CRM 4.4-16x1.6

301 UCU-60013 WH JOY STICK

(D-2/2)

PARTS LIST

(3) ASSY SUB CABINET (UCU-1001)

(D-1/2)

Details for (25) installation position.

Details of part "E" (S=1/2)

Details of part "F" (S=1/1)

Details of part "G" (S=1/2)Details of part "J" (S=1/2)Details of part "I" (S=1/2) Details of part "H" (S=1/2)

NOTE: (26) is to be affixed in alignment with

the rectangular holes as shown in each

figure. It must be affixed securely by

being pressed adequately.

PARTS LIST

1 UCU-1002 CABINET 2 UCU-1023 COIN CHUTE LOWER 3 UCS-1007 SASH UPPER 4 UCS-1008 SASH SIDE 5 UCU-1024 SASH LOWER 6 UCU-1025 BOX ADJUST WALL L 7 UCU-1026 BOX ADJUST WALL R 8 UCU-1027 HOOK UPPER L 9 UCU-1028 HOOK LOWER L 10 UCU-1029 HOOK UPPER R 11 UCU-1030 HOOK LOWER R 12 UCU-1031 FL GLASS 13 UCU-1032 FL GLASS SHEET 14 UCU-1033 FL GLASS SASH A L 15 UCU-1034 FL GLASS SASH A R 16 UCU-1035 FL GLASS SASH B 17 UCU-0007 GLASS EDGE GUARD A 18 UCU-1036 GLASS EDGE GUARD C 19 UCU-1037 LOOVER COVER 20 253-5460-02 AIR VENT WHITE 21 UCS-1046 FLAP CUSHION T10 22 UCS-1022 DOOR CUSHION 23 UCU-1038 AC UNDER COVER 24 USS-1023 FLAP STOPPER 25 USS-1024 DOOR ADJUSTER 26 UCU-1039 TNG CUSHION 27 UCU-6001 ASSY WIRE

101 509-5753 LINE INTERRUPT SW 102 280-5277 CORD CLAMP 18 103 280-5292 CORD CLAMP 18 PUSH TYPE 104 280-5275-SR10 CORD CLAMP SR10 105 280-6581-29 BUSHING NB-29

201 000-P00312-W M SCR PH W/FS M3x12 202 000-P00408-W M SCR PH W/FS M4x8 203 000-T00408-0C M SCR TH CRM M4x8 204 010-F00308 S-TITE SCR FH M3x8 205 050-F00400 FLG NUT M4

301 UCU-60001 WH AC PRI 302 UCU-60017 WH PRIZE SENSOR

ITEM NO. PART NO. DESCRIPTION NOTE

(D-2/2)

PARTS LIST

(4) CABINET (UCU-1002)

(D-1/2)

PARTS LIST

1 UCU-1002-A CABINET BLANK

101 601-8714 CASTER FAI100 102 601-5699X LEG ADJUSTER BOLT M16x75

201 030-001020-S HEX BOLT W/S M10x20 202 060-F01000 FLT WSHR M10 203 050-H01600 HEX NUT M16

ITEM NO. PART NO. DESCRIPTION NOTE

(D-2/2)

PARTS LIST

(5) ASSY WIRE (UCU-6001)

101 601-0460 PLASTIC TIE BELT 100 M/M 102 310-5033-15-160 SPIRAL TUBE 15 160CM

301 UCU-60002 WH AC FL 302 UCU-60003 WH AC SEC 303 UCU-60004 WH CABI 1 304 UCU-60007 WH FL EXT 305 UCU-60008 WH CABI 2 306 UCU-60009 WH DIPSW BD 307 UCU-60010 WH SP EXT 308 UCU-60012 WH CREDIT BD

ITEM NO. PART NO. DESCRIPTION NOTE

This is comprised of the following wire harnesses. ASSY drawing is not available.

NOTE: Pay close attention to the surface orientation of

the cross-section (slanted line) area.

PARTS LIST

(6) ASSY SPEAKER (UCS-1050X)

1 UAT-1051 SPEAKER BASE

101 130-5034 SPEAKER 8 OHM 10W F 100A59-1

201 012-P00408 TAP SCR #2 PH 4x8

ITEM NO. PART NO. DESCRIPTION NOTE

NOTE: Pay close attention to the surface orientation of

the cross-section (slanted line) area.

PARTS LIST

(7) ASSY SERVICE DOOR (UCU-1060)

(D-1/2)

(Earth terminal)

PARTS LIST

1 UCU-1061 SERVICE DOOR 2 UCU-1062 STICKER SERVICE DOOR 3 UCU-1063 LT SOLENOID BRKT FOR LORENZO 4 DP-1148X LKG TNG 5 421-12106-02 STICKER BULB 2.2W12V UL

101 220-5793-1-A002 CLY LOCK MASTER W/O KEY A002 102 124-5088 SOL QL-102 DC12V FOR 220-5310 103 220-5208-05 COIN CHUTE REJ 25 AD-81P 104 220-5786 C.C BRKT A0710 (LORENZO) 105 601-6316-S8 TIE BELT W/CLAMP S8 106 601-0460 PLASTIC TIE BELT 100 M/M 107 280-5275-SR10 CORD CLAMP SR10

201 000-P00308-W M SCR PH W/FS M3x8 202 000-P00408-W M SCR PH W/FS M4x8 203 050-F00400 FLG NUT M4

301 UCS-60031 WH EARTH DOOR 302 UCU-60015 WH SERVICE DOOR

ITEM NO. PART NO. DESCRIPTION NOTE

(D-2/2)

PARTS LIST

(8) SW UNIT (UCU-1070)

1 UCU-1071 SW AND VOL PLATE 2 837-14485R DIPSW BD USS 3 421-12100 STICKER SW UNIT UCU

101 220-5798-01 MAG CNTR 4P MZ674-DC5V-D41 JC 102 220-5798-02 MAG CNTR 6P MZ674-DC5V-D42 JC 103 509-6102-V-B SW ROCKER J8 V-B AJ8202BF 104 601-0460 PLASTIC TIE BELT 100 M/M

201 050-F00300 FLG NUT M3

ITEM NO. PART NO. DESCRIPTION NOTE

(Connector: White) (Connector: Yellow)

NOTE: DIP SW 1 ~ 4 should all be set to OFF.

PARTS LIST

(9) AC UNIT (UCU-1080)

1 UCU-1081 AC BRKT 2 421-7468-01 STICKER C.P W/PIC

101 214-0202 AC INLET PANEL TYPE 102 270-5020 NOISE FILTER AC250V 6A 103 509-6102-V-B SW ROCKER J8 V-B AJ8202BF 104 512-5046-5000 C.P 5000MA CE UL 105 280-5275-SR10 CORD CLAMP SR10 106 601-0460 PLASTIC TIE BELT 100 M/M

201 010-P00308-F S-TITE SCR PH W/F M3x8 202 050-F00400 FLG NUT M4

301 UCS-60035 WH EARTH FILTER L 302 UCU-60021 WH AC UNIT

ITEM NO. PART NO. DESCRIPTION NOTE

(E a r th t e r mina l )

PARTS LIST

(10) ASSY PRIZE SENSOR (USS-1200)

1 UCS-1202 PRIZE SENSOR PLATE B

101 370-5173-01 PHOTO SENSOR OMT-15DJST-YL

201 012-P00314 TAP SCR #2 PH 3x14 202 FAS-680014 FLT WSHR 3-12X1.6

ITEM NO. PART NO. DESCRIPTION NOTE

Light r e c e p t i o n 3P Conn e c t o r

Light e m i s s i o n 2P Conn e c t o r

Light r e c e p t i o n 3P Conn e c t o r

Light e m i s s i o n 2P Conn e c t o r

PARTS LIST

(11) ASSY FL BASE L (UCU-1300)

1 UCU-1301 CEILING FL BASE L 2 UCU-1302 FL HOLDER BRKT A 3 UCU-1303 FL HOLDER BRKT B

101 214-0271 FL SOCKET 26.420.4400.50 BJB 102 280-6581-8 BUSHING NB-8 103 601-0460 PLASTIC TIE BELT 100 M/M

201 000-P00408-W M SCR PH W/FS M4x8

301 UCU-60025 WH FL 3

ITEM NO. PART NO. DESCRIPTION NOTE

PARTS LIST

(12) ASSY FL BASE R (UCU-1310)

1 UCU-1311 CEILING FL BASE R 2 UCU-1302 FL HOLDER BRKT A 3 UCU-1302 FL HOLDER BRKT A 4 421-12109-32T8 STICKER FL RATING 32T8 5 421-12107 STICKER HOT SURFACE UL

101 214-0272 FL SOCKET 26.420.4404.50 BJB 102 390-6828 INVERTER QT2X32 T8/120 ISN-SC 103 601-0460 PLASTIC TIE BELT 100 M/M 104 209-0032-91 CONN CLOSED END

201 000-P00408-W M SCR PH W/FS M4x8 202 000-P00410-W M SCR PH W/FS M4x10 203 068-441616 FLT WSHR 4.4-16x1.6

301 UCU-60023 WH FL 1 302 UCU-60024 WH FL 2 303 UCU-60027 WH FL SOCKET

ITEM NO. PART NO. DESCRIPTION NOTE

PARTS LIST

(13) SIDE FL UNIT (UCU-1320)

1 UCU-1321 SIDE FL BASE 2 421-12109-25T8 STICKER FL RATING 25T8

101 214-0271 FL SOCKET 26.420.4400.50 BJB 102 214-0272 FL SOCKET 26.420.4404.50 BJB 103 390-6829 INVERTER QT1X32 T8/120 ISN-SC 104 280-5275-SR10 CORD CLAMP SR10 105 209-0032-91 CONN CLOSED END 106 601-0460 PLASTIC TIE BELT 100 M/M

201 050-F00400 FLG NUT M4 202 068-441616 FLT WSHR 4.4-16x1.6

301 UCU-60022 WH FL SIDE 302 UCU-60027 WH FL SOCKET

ITEM NO. PART NO. DESCRIPTION NOTE

PARTS LIST

(14) FLAP UNIT (UCU-1340)

1 UCU-1341 FLAP PANEL 2 UCU-1342 STICKER FLAP 3 UCU-1343 FLAP HINGE 4 UCU-1344 DAMPER BRKT A 5 UCU-1345 DAMPER BRKT B 6 UCU-1346 DAMPER SLEEVE 7 UCU-1347 FLAP INNER

101 601-11728 TORQUE DAMPER TD14A1-20K-R

201 000-P00320-W M SCR PH W/FS M3x20 202 000-T00408-0C M SCR TH CRM M4x8 203 050-F00400 FLG NUT M4

ITEM NO. PART NO. DESCRIPTION NOTE

Pa y c l o s e atte n t i o n to th e o r i e ntation .

Attach ( 1 0 1 ) i n t h e condition i n w h i c h it was d e l i v e r e d , then turn i t 9 0 d e g r e e s.

PARTS LIST

(15) ASSY GLASS DOOR L (UCU-1100)

1 UCU-1101 FRONT GLASS 2 UCS-1102 LOCK BRKT 3 UCS-1103 LOCK PLATE 4 UCM-1101 LOCKING TONGUE 5 UCU-1102 LOCK BRKT LOWER 6 UCU-1103 INTERLOCK PLATE L

101 220-5793-1-A002 CLY LOCK MASTER W/O KEY A002

ITEM NO. PART NO. DESCRIPTION NOTE

Sega UFO CATCHER User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual