Sega TROPHY HUNTING 2003 User Manual

OPERATING MANUAL for:
DEDICATED CABINET,
CONVERSION KIT
&
(From Wing Shooting Championship to Trophy Hunting)
901 Cambridge Drive Elk Grove Village, IL 60007 Phone: (847) 364-9787 Fax: (847) 364-9831 Web: www.sammyusa.com Toll free: 1-888-US-SAMMY
© 2002 Sammy USA Corporation
CONTENTS
PLEASE READ BEFORE INSTALLING… Page 1
1. SPECIFICATIONS (DEDICATED CABINET) Page 2
2. CHIP UPDATE KIT PACKAGE CONTENTS Page 3
3. KIT PACKAGE CONTENTS Page 4
4. GAME PLAY Page 5
5. HANDLING AND INSTALLATION Page 6
6. CONNECTOR TABLE Page 7
7. DIP SWITCH TABLE Page 8
8. CHIP UPDATE LOCATION AND INSTALLATION Page 9, 10
9. KIT INSTALLATION Page 11, 12
10. TEST MODE Page 13, 14, 15
11. TROUBLE WITH GUN SHOOTING Page 16
12. WARRANTY Page 17
13. ELECTRICAL WIRING DIAGRAM (DEDICATED CABINET) Page 18
PLEASE READ BEFORE INSTALLING THE
TROPHY HUNTING KIT
The TROPHY HUNTING KIT is designed only for a Normal resolution monitor. The High or Medium resolution monitor will not work for TROPHY HUNTING KIT.
MIS-CONNECTING THE GUN CONNECTOR
When you connect the Gun unit to Main PCB, you must al­ways make sure to connect to the correct connectors which are CN 5 & CN 6 and CN 7 & CN 8 connectors.
If you connect Gun unit to CN 2, 8 pin connector, your PCB will sustain serious damage.
Connect 10 pin connector of
Gun Assy Connector to both 4
pin connectors as shown.
Connector of
1 Player Gun Assy
CN 5 & CN6
Connector of
2 Player Gun Assy
CN 2
CN 7 & CN 8
CAUTION!!
NEVER
CONNECT
GUN UNIT
TO CN2.
1
1. SPECIFICATIONS (DEDICATED CABINET)
POWER 120VAC @ 60Hz USA & CANADA / 230VAC @ 50Hz EUROPE DIMENSIONS Width: 26.5” (673 mm)
Height: 73.5” (1867 mm) Depth: 33” (838 mm) with Gun Assy = 40” (1016 mm)
WEIGHT: 311 lbs (142 kg)
Main PCB , Trophy
Part #: 48-10-001
Manual, Trophy
Part #: 48-30-311
“PUMP BEFORE
SHOOTING” Decal, Trophy
Part #: 48-30-224
Instruction Decal, Trophy
Part #: 48-30-210
Start Button Assy,
Hunter 1, Trophy
Part #: 48-50-013
Sammy 27” Shotgun Assy
Part #: 99-50-310
Marquee, Trophy
Part #: 48-30-111
Side Decal, Trophy
Part #: 48-30-200
H = 73.5”
(1867 mm)
Start Button Assy,
Hunter 2, Trophy
Part #: 48-50-015
Control panel Overlay,
UR 25” VIDEO
Part #: 99-30-161
Security Bar KIT,
Mid door
(OPTIONAL)
Part #: 99-70-278
W = 26.5” (673 mm)
2
*D = 33”
(838 mm)
*With Gun Assy: D = 40”
(1016 mm)
2. CHIP UPDATE KIT PACKAGE CONTENTS
CHIP UPDATE KIT
MASK ROM set (5 PCS/SET) START button Assy,
A
Part#: 48 -90-800
Instruction Decal Sheet Program EP-ROM set (2 PCS/SET)
E “Pump Before shooting” Decal
Part#: 48 -30-210
B
Hunter 1 Part#: 48 -50-013
Part#: 48 -30-224
C START button Assy,
Hunter 2
Part#: 48 -50-015
F D
Part#: 48 -90-000
H
G Marquee Styrene
Part#: 48 -30-100
Side Decal (2 sheet) Part#: 48 -30-200
I
Instructions
Part#: 48 -30-301
MANUAL
J Conversion Kit
AAMA Sticker Part#: 99 -30-750
ANIMATED
VIOLENCE
MILD
3
3. KIT PACKAGE CONTENTS
A
Main P.C.Board Trophy Hunting
48-10-001
B
START button Assy, Hunter 1
48-50-013
E “PUMP BEFORE SHOOTING”
Decal 48-30-224
H Side Decal (2 sheets)
48-30-200
C START button
F Marquee Styrene
48-30-100
Assy, Hunter 2 48-50-015
G
I Gun Holster (2 sets)
99-50-303
D
Instruction Decal Sheet 48-30-210
Control Overlay 99-30-150
L
Gun Assy (2 guns) 99-50-310
J Conversion Kit
Instructions
48-30-300
MANUAL
K AAMA Sticker
99-30-750
ANIMATED
VIOLENCE
MILD
4
4. GAME PLAY
Trophy Hunting is a sports hunting game that has an exciting COMPETI-
TION MODE. Two players can play at the same time in competition mode which is a Sammy USA “EXCLUSIVE”!
HOW TO PLAY
? Insert coin(s) and press Hunter 1 or Hunter 2 button to start game. ? Use Sammy 27” Shotgun to (Pump the Shotgun before you shoot the screen each
time.) Select one of 6 states. Colorado, Idaho or Maine for Bear and 3 states Mon­tana, Utah or Alaska for Moose.
? Use Sammy 27” Shotgun to select weapon. There are 4 kinds of weapons.
Bolt-Action Rifle (Ammo x 4), Compound Bow (Ammo x 8) Revolver with scope (Ammo x 6), Muzzleloader (Ammo x 1)
? 12 areas per state with one bonus stage after the 6th area. The Bonus stage is TAR-
GET SHOOTING.
5
5. HANDLING AND INSTALLATION PLEASE TAKE A MOMENT TO READ THE FOLLOWING BEFORE
YOU TURN ON YOUR NEW GAME.
The Trophy Hunting video game is an indoor game machine. It is not designed for outdoor use. Avoid installing the game in the following locations:
À Locations subject to rain or water damage À Locations in direct sunlight À Locations subject to extreme heat À Locations near hazardous or flammable liquids or chemicals
You will need the following minimum dimensions for egress into your location:
À 80 inches in height À 30 inches in width
INSTALLATION
Unpack your game carefully. Be careful of the shipping staples. They can be sharp. Your game is assembled and should not need any assembly. Level your game using enclosed Leg levelers. The standard voltage for U.S. and Canada 120V / 125V - 3A; Europe 220V / 240V - 2A. Use of extension cords is prohibited. Use only a grounded outlet. YOUR GAME MUST BE GROUNDED!!! The minimum space required for operation in your location should be:
À 80” high À 30” wide À 75” depth
THE GAME MUST BE LEVEL. USE A LEVEL TO AVOID NEEDLESS ADJUSTMENTS.
SAFETY PRECAUTIONS
À Be sure to turn the power off or unplug the game before working on the unit. À Do not unplug game by pulling on the line cord. À Replace line cord if the insulation is damaged in any way with one of equal quality. À Replace open fuses with same type and rating. À Re-check and re-seat all harness connections.
6
6. CONNECTOR TABLES
SOLDER SIDE
FUNCTION COLOR PIN # PIN # COLOR FUNCTION
GROUND BLK GROUND BLK
+5VDC RED +5VDC RED
+12VDC BLU
KEY
COIN METER B
COIN LOCKOUT B
SPEAKER(-) BLK
VIDEO GREEN GRN
VIDEO SYNC WHT
SERVICE CREDIT SWITCH
COIN SWITCH B
2P START BUTTON
GROUND BLK GROUND BLK
BRN/WHT
JAMMA CONNECTOR
MAIN P.C.BOARD
COMPONENT SIDE
A 1 B 2 C 3 D 4
BLK GROUND
BLK GROUND RED +5VDC RED +5VDC
E 5
F 6
BLU +12VDC
H 7
J 8
K 9
L 10
WHT/BLK SPEAKER(+)
M 11
N 12 P 13 R 14 S 15
RED VIDEO RED
BLU VIDEO BLUE
BLK VIDEO GROUND
WHT/GRY TEST SWITCH
T 16 U 17 V 18
W 19
X 20 Y 21
Z 22
a 23
b 24
c 25
d 26
e 27
f 28
BLK GROUND BLK GROUND
KEY
COIN METER A
COIN LOCKOUT A
COIN SWITCH A
1P START BUTTON
CN6 - 4 PIN SUB CONNECTOR
MAIN P.C.BOARD (1P GUN)
PIN # COLOR FUNCTION
1 2 3 4
GREEN PUMP SWITCH
BLACK PUMP SWITCH GND
CN5 - 4 PIN SUB CONNECTOR
MAIN P.C.BOARD (1P GUN)
PIN # COLOR FUNCTION
7 8 9
10
RED +5VDC
WHITE TRIGGER SWITCH
BROWN GROUND
BLUE OPTICAL
CN8 - 4 PIN SUB CONNECTOR
MAIN P.C.BOARD (2P GUN)
PIN # COLOR FUNCTION
1 2 3 4
GREEN PUMP SWITCH
BLACK PUMP SWITCH GND
CN7 - 4 PIN SUB CONNECTOR
MAIN P.C.BOARD (2P GUN)
PIN # COLOR FUNCTION
7 8 9
10
RED +5VDC
WHITE TRIGGER SWITCH
BROWN GROUND
BLUE OPTICAL
7
7. DIP SWITCH TABLES
DIP SWITCH 1
FUNCTIONS SETTING 1 2 3 4 5 6 7 8
COIN CHUTE A, B 1 COIN START, 1 COIN CONTINUE OFF OFF OFF OFF
3 COINS START, 2 COINS CONTINUE OFF OFF ON OFF
4 COINS START, 4 COINS CONTINUE OFF ON ON OFF 4 COINS START, 3 COINS CONTINUE ON ON ON OFF
1 COIN 2 CREDITS, 1 CREDIT START & CONTINUE OFF ON OFF ON
1 COIN 4 CREDITS, 1 CREDIT START & CONTINUE OFF OFF ON ON 1 COIN 5 CREDITS, 1 CREDIT START & CONTINUE ON OFF ON ON
FREE PLAY ON ON ON ON
NOT USED OFF OFF OFF
TEST MODE OFF OFF
ON ON
2 COINS START, 2 COINS CONTINUE ON OFF OFF OFF
2 COINS START, 1 COIN CONTINUE OFF ON OFF OFF 3 COINS START, 3 COINS CONTINUE ON ON OFF OFF
3 COINS START, 1 COIN CONTINUE ON OFF ON OFF
4 COINS START, 2 COINS CONTINUE OFF OFF OFF ON 4 COINS START, 1 COIN CONTINUE ON OFF OFF ON
1 COIN 3 CREDITS, 1 CREDIT START & CONTINUE ON ON OFF ON
1 COIN 6 CREDITS, 1 CREDIT START & CONTINUE OFF ON ON ON
DIP SWITCH 2
FUNCTIONS SETTING 1 2 3 4 5 6 7 8
MONITOR SETTING 1 NORMAL OFF
REVERSE VERTICAL ON
MONITOR SETTING 2 NORMAL OFF
ATTRACT SOUND ON OFF
OFF ON
DIFFICULTY LEVEL NORMAL OFF OFF
HARD OFF ON HARDEST ON ON
BLOOD COLOR RED OFF
CHANCES 2 OFF
3 ON
GUN TYPE PUMP ACTION GUN UNIT OFF
REVERSE HORIZONTAL ON
EASY ON OFF
YELLOW ON
HAND GUN UNIT ON
SWITCH POSITIONS
SWITCH POSITIONS
"FACTORY INSTALLED" SETTING
8
8. CHIP UPDATE LOCATION AND INSTALLATION
1. Exhange the ROMS
MAIN P.C.BOARD
SUB CONNECTOR
4 PINS X 2 (2P GUN)
1
CN 8 CN 7
U40, MASK ROM WSC: AS1003 Trophy: AS1103
There are 5 pcs of MASK-ROMS and 2 pcs of Program EP-ROMS on Wing Shooting Championship Main PCB. Remove the Wing Shooting Championship Main PCB from your cabinet. Refer to the position of all ROMS as shown below to exchange to the Trophy Hunting ROMS.
SUB CONNECTOR
4 PINS X 2 (1P GUN)
U07, Program
JAMMA CONNECTOR
10
1
CN 6 CN 5
DIPSW 1
8 1
ON
OFF
10
EP-ROM
VOLUME
MAX
U39, MASK ROM WSC: AS1002 Trophy: AS1102
U41, MASK ROM WSC: AS1004 Trophy: AS1104
U38, MASK ROM WSC: AS1001 Trophy: AS1101
1
DIPSW 2
U06, Program
8
ON
OFF
EP-ROM
U18, MASK ROM WSC: AS1005 Trophy: AS1105
9
2. Change the GAME CABINET
MARQUEE STYRENE Change the Wing Shooting Championship M arquee to the TROPHY HUNTING
Marquee.
NOTE: If the TROPHY HUNTING Marquee Styrene does not fit your cabinet,
you should cut the marquee to fit.
• HUNTER 1 AND HUNTER 2 BUTTONS Take off the Wing Shooting Championship Hunter 1 and Hunter 2 button assys
from the control panel. Then put on the TROPHY HUNTING Hunter 1 and Hunter 2 button assys.
INSTRUCTION SHEET (HOW TO HUNT) Take off the Wing Shooting Championship INSTRUCTION SHEET (HOW TO
HUNT) from the control panel. Then put on the TROPHY HUNTING INSTRUCTION SHEET (HOW TO HUNT).
SIDE DECALS Change the Wing Shooting Championship Side decals to the TROPHY
HUNTING Side decals.
INSTRUCTION DECAL SHEET Put “PUMP BEFORE SHOOTING” Decal Sheet on the front glass of the monitor.
AAMA “ANIMATED VIOLENCE MILD” STICKER Place AAMA sticker on the upper left hand side corner of the marquee.
MONITOR
ANIMATE
VIOLENCE
MILD
PUMP BEFORE SHOOTING
AAMA STICKER
DECAL
10
9. KIT INSTALLATION
1. Change the GAME CABINET
MARQUEE STYRENE Change the old marquee to the TROPHY HUNTING Marquee Styrene.
NOTE: If the TROPHY HUNTING Marquee Styrene does not fit your cabinet,
you should cut the marquee to fit.
• CONTROL PANEL Change the parts on the control panel. Take off the old parts (Joystick or Gun unit assy) and the old push button assys from the control panel. Then put on the TROPHY HUNTING Control Panel Overlay .
NOTE: After you put on the TROPHY HUNTING Control Panel Overlay, you must
make the holes for the TROPHY HUNTING Gun Assy, Gun Holster and Push Button Assy. See sample layout below. Or if you want, install Gun Assy or Gun Holster on the side of Cabinet.
MOUNTING DIMENSIONS FOR PUSH BUTTON ASSY MOUNTING DIMENSIONS FOR GUN ASSY
0.20 dia. 3 HOLES
1.0” dia. HOLE
1.50”
3.00”
1.50”
2.47”
0.87”
1.60”
1.5” dia. HOLE
MOUNTING GUN HOLSTER You can mount GUN HOLSTER to the top of the control panel or side of
cabinet. To mount it, use HOLSTER as a template for drilling holes. Use a hex
wrench to tighten screws.
IF YOU WANT TO INSTALL A HAND GUN:
You can use a HAND GUN instead of the original pump action gun for this game.
*WARNING*
Be absolutely sure that the connector for the hand gun matches exactly the pin position for CN5 (1P Gun) and CN7 (2P Gun) as shown on page 4. Connect 1P Gun connector to CN5, 2P Gun connector to CN7 and turn on Dip switch 2, #8. See page 5 for Dip switch table.
11
INSTRUCTION DECAL SHEET
MONITOR
Put “PUMP BEFORE SHOOTING” Decal Sheet on the front glass of the monitor.
AAMA “ANIMATED VIOLENCE MILD” STICKER Place AAMA sticker on the upper left hand side corner of the marquee.
ANIMATE
VIOLENCE
MILD
Remove old P. C .Boards and install new P. C. Board in its place.
PUMP BEFORE SHOOTING
AAMA STICKER
DECAL
2. Connect the HARNESSES
10 pin connector from GUN Assy (1P)
CN 5
Connectors on the Main PCB
JAMMA HARNESS Connect the JAMMA Harness to the edge connector on the TROPHY
HUNTING Main P.C.BOARD.
GUN HARNESS Connect the Gun Harness to the Gun Connectors located on the Main P.C.
Board components side, at CN5 & 6 and CN7 & 8 connectors on the P.C. BOARD. Connect Gun Connector to CN5 & 6 and CN7 & 8, correctly, as shown below.
10 pin connector from GUN Assy (2P)
1 10
CN 6
CN 7
1 10
CN 8
Connectors on the Main PCB
12
10. TEST MODE
Entering the TEST MODE
Select TEST
1. GUN MENU
If you need to check the condition of the game circuitry and controls, you can use the TEST MENU. Turn ON “DIP SWITCH 1, #8” and re-power on the game. The game will go into TEST MODE (diagnostics) and the screen appears as follows:
Use this screen to choose which of the 7 screens you want to see. Move cursor using the START BUTTON. Then pull the TRIGGER to enter the function.
You can adjust GUN unit in GUN ADJUST mode.
Gun Adjust
1. Enter TEST MENU and select GUN ADJUST.
2. Shoot center mark only with gun sight.
SHOOT CENTER MARK ONLY TO ADJUST
TEST MENU
1. GUN MENU
2. COLOR TEST
3. CROSS HATCH
4. I/O TEST
5. SOUND TEST
6. MEMORY TEST
7. OPTIONAL SETTING
8. REBOOT
CURSOR
GUN ADJUST
X
PRESS START BUTTON TO GUN TEST
3. If you need more accuracy, try again.
4. Press START button to save Gun accu­racy and enter GUN TEST mode, press START button again to go back to Main menu.
2. COLOR TEST
You can test accuracy in GUN TEST mode.
Gun Test
1. At Gun Adjust screen, press START button to go to test mode.
2. Shoot all around the screen to see Gun’s accuracy.
3. Press START button to go back to Main menu.
Use this screen to check the color of monitor. The color blocks in the center should be four bands (Red, Green, Blue and White from top to bottom), each with a color scale from dark to bright, left to right. If the screen does not match this description, adjust the Monitor as described in the Monitor’s manual. * Press the START button to exit and go back to the TEST MENU screen.
X
GUN TEST
PRESS START BUTTON TO EXIT
COLOR TEST
RED
GREEN
BLUE
WHITE
PRESS START BUTTON TO EXIT
13
3. CROSS HATCH
Use this screen to check the size of picture. The CROSS HATCH test pattern has a White grid on a Black background. Check following:
- The grid line should be straight, and the lines should not have excessive pincushion or barrel distortion.
- “Out”line of grid line is the same size as “Out”line of game screen. So, “Out” line should be able to be seen with no overflow of grid lines on screen. If these are not as above, adjust the Monitor as described in the Monitor’s manual. * You can exit and go back to the TEST MENU screen by press START button.
CROSS HATCH
PRESS START BUTTON TO EXIT
4. I/O TEST
5. SOUND TEST
6. MEMORY TEST
Use this screen to check the switches in this game. To check the functioning of each switch, activate it and watch the corresponding OFF letters change to ON. If the ON and OFF letters do not appear correctly, check the Harness connections and Switches.
* Press START button and Gun trigger simultaneously to exit.
Use this screen to check all game sounds. Choose a sound with the START buttons. (Hunter 1 = forward, Hunter 2 = Back) Then pull the TRIGGER. You can check each sound in this game.
* Press START button and Gun trigger simultaneously to exit.
Use this screen to check RAM and ROM on the Main P.C.B. The Main P.C.B. will automatically check them when you enter this screen. If there are no problems, the word OK will appear on screen. If you get the word ERROR, check the mounting of RAMs or ROMs on the Main P.C.B. and if ERROR reappears, it needs to be replaced.
I/O TEST
COIN A : OFF COIN B : OFF SERVICE : OFF TEST : OFF
1P GUN START : OFF PUMP : OFF TRIGGER : OFF
PRESS START & GUN TRIGGER TO EXIT
2P GUN START : OFF PUMP : OFF TRIGGER : OFF
SOUND TEST
SOUND CODE 000
BLAK_SHOT
PRESS START BUTTON TO CHOOSE PRESS GUN TRIGGER TO PLAY
PRESS START & GUN TRIGGER TO EXIT
MEMORY TEST
WORK RAM : OK BACKUP RAM : OK
ROM (U06) : OK ROM (U07) : OK
* This mode will automatically exit af­ter testing is finished.
14
7. OPTIONAL SETTING
HIGH SCORE CLEAR
If you desire to clear HIGH SCORE data, do the following.
HOW TO SET UP
1. Enter TEST MENU and select OPTIONAL SETTING.
2. Press START BUTTON to choose HIGH SCORE CLEAR.
3. Select YES by pressing START BUTTON and pressing GUN TRIGGER to clear HIGH SCORE data.
4. The screen will return to previous screen automatically after clearing HIGH SCORE data.
NOTE: Do not proceed if Gun test is accurate.
OPTIONAL SETTING
1. HIGH SCORE CLEAR
2. GUN ADJUST DEFAULT
3. RETURN TO TEST MENU PRESS START BUTTON TO CHOOSE PRESS GUN TRIGGER TO SELECT
HIGH SCORE CLEAR
ARE YOU SURE YOU WANT TO CLEAR
HIGH SCORE? YES
g NO
PRESS START BUTTON TO CHOOSE
PRESS GUN TRIGGER TO SELECT
8. REBOOT
GUN DATA DEFAULT
If you have problem with Gun sighting , you may have to clear the Gun data. After clearing Gun data, the game will be reset to factory default setting. See the following for how to clear saved data.
1. Enter TEST MENU and select OPTIONAL SETTING.
2. Press START BUTTON to choose GUN AD­JUST DEFAULT.
3. Select YES by pressing START BUTTON and pressing GUN TRIGGER to clear Gun data.
4. The screen will return to previous screen automatically after clearing Gun data.
Use this screen to go back to normal game mode. After selecting this function, the game will automatically take you to the normal game screen. Make sure to turn OFF “DIP SWITCH 1, #8” or you will return to test mode upon powering on.
GUN ADJUST DEFAULT
ARE YOU SURE YOU WANT TO SET GUN ADJUST DEFAULT? YES
g NO
PRESS START BUTTON TO CHOOSE
PRESS GUN TRIGGER TO SELECT
Returning to
GAME MODE
You can return to normal game mode by doing one or the other of the following: Turn OFF “DIP SWITCH 1, #8” and re-power on the game. Select REBOOT at TEST MENU. (But you will have to make sure to turn OFF “DIP SWITCH 1, #8”.)
15
11. TROUBLE WITH GUN SHOOTING
If you have trouble because you can’t shoot to the corner of the screen, you may have to adjust the monitor brightness. Turn up the monitor brightness until you can shoot the corner of screen.
Plus, monitors tend to develop a magnetic field from continuous use, which would cause the gun unit not to function properly. Therefore, it is recommended that the monitor is demagnetized [degaussed] every so often in order to keep the gun unit functioning properly.
In addition, the following conditions of the monitor may result in Gun shooting problems:
? Picture burned on monitor screen ? Over gauzed monitor ? Non adjustable brightness feature
Also, the following conditions of the cabinet may result in Gun shooting problems.
? Combination of low performing adjustable brightness
monitor and low reflection mirror
? Dirty monitor screen or monitor grass
GUNSHOT ACCURACY IMPROVEMENT
If you have trouble because you can’t calibrate the gun unit properly. For example you can’t shoot corner of screen or you can shoot only in the cen­ter of the screen, do the following:
1) CHECK THE +5V LINE ON THE PCB. YOU CAN CHECK VOLTAGE AT THE JAMMA EDGE CONNECTOR BETWEEN PIN #2 AND #3.
2) ADJUST +5V LINE TO +5.25V BY TURNING UP POTENTIOMETER ON THE POWER SUPPLY.
WARNING: DO NOT TURN UP VOLTAGE MORE THAN +5.25V OTHERWISE YOUR PCB WILL SUSTAIN SERIOUS DAMAGE.
3) ENTER BACK UP CLEAR IN TEST MODE, THEN SELECT YES TO CLEAR BACK UP DAT A.
NOTE: YOU DON’T HAVE TO DO “GUN ADJUST” IN TEST MODE.
4) ENTER GUN TEST IN TEST MODE TO CHECK GUNSHOT. IF THE GUNSHOT IS NOT CORRECTED REPEAT STEP #3.
16
12. WARRANTY
Limited warranty, Repair and Return Policy
Sammy USA Corporation warrants all products to be free from defective materials and workmanship for a period of thirty (30) days from the Sammy USA Corporation invoice date unless otherwise specified in writing by Sammy USA Corporation. The extent of this warranty applies to all electronic assemblies only, and does not include lamps and fuses. This limited warranty is invalid for any product that upon examination, is deemed to have been subject to misuse, improper repair or installation, neglect or violatio n of specification or other instructions published by Sammy USA Corporation. There are no additional warranties which extend bey ond those limited warranties described above. The limited warranties described above shall be in lieu of any other warranty, express or implied, including but not limited to any implied warranty of merchantability or fitness for a particular purpose.
Return Merchandise Authorization
1. Contact your authorized Sammy USA distributor to receive a Return Merchandise Authorization for return.
2. You must obtain RMA numbers from Sammy USA Corporation through an authorized Sammy USA
distributor. Please have your serial number available when calling for an RMA number.
3. All items must have an RMA number marked clearly on the outside of the package.
4. Products must be shipped prepaid. Products returned without an RMA number will not be
accepted.
5. Credits to accounts are subject to inspection of products for damage and suitability for resale.
17
13. ELECTRICAL WIRING DIAGRAM (Trophy, DEDICATED CABINET)
JAMMA Connector (56 pins) on Main CPU Board
GND 1 GND A GND 2 GND B +5VDC 3 +5VDC C +5VDC 4 +5VDC D
+12VDC 6 +12VDC F KEY 7 KEY H COIN METER A 8
COIN LOCKOUT A 9
SPEAKER (+) 10 SPEAKER (-) L
VIDEO RED 12 VIDEO GREEN N VIDEO BLUE 13 VIDEO SYNC P VIDEO GND 14 SERVICE CREDIT SWITCH R TEST SWITCH 15
COIN SWITCH A 16
1P START BUTTON 17 2P START BUTTON U
GND 27 GND e GND 28 GND f
5 E
J
K
11
M
S
T
18
V
19
W
20
X
21
Y
22
Z
23
a
24
b
25
c
26
d
Fluorescent Lamp Assy , Marquee
Sub Connector CN6 (4 pins) on Main CPU Board (1P GUN)
1P PUMP SW 2 1P PUMP SW GND 3
Sub Connector CN5 (4 pins) on Main CPU Board (1P GUN)
+5VDC 7 1P TRIGGER SW 8 GROUND 9 OPTICAL 10
Sub Connector CN8 (4 pins) on Main CPU Board (2P GUN)
2P PUMP SW 2 2P PUMP SW GND 3
Sub Connector CN7 (4 pins) on Main CPU Board (2P GUN)
+5VDC 7 2P TRIGGER SW 8 GROUND 9 OPTICAL 10
Speaker 8 ohm, 4W
Speaker 8 ohm, 4W
1
4
1
4
Gun Connector, 1P (JST 10 PIN)
Gun Connector, 2P (JST 10 PIN)
18
9 PIN CONNECTOR
1 +5VDC (RED) 2 GROUND (BLACK) 3 +12VDC (YELLOW)
3 PIN CONNECTOR
1 AC115V 2 EARTH 3 AC115V
Power Supply UNIT (BS200P) +5VDC (20A) +12VDC (8A)
AC
115V IN
1 AC115V 2 EARTH 3 AC115V
10 RED
9 GREEN 8 BLUE 7 GND 1 SYNC
Switch Bracket
Service Credit Switch
Coin Door
8 COIN IN 7 GND 6 AC115V 4 AC115V 3 NEUTRAL
A/C Line cord
BLK GRN WHT
25” TV MONITOR ASSY
TEST Switch
Option 9 PIN
connector
(DBA Mars
AE2451)
Coin Switch
Coin Switch
1P Start Button (Hunter 1)
2P Start Button (Hunter 2)
GUN ASSY, 1P
GUN ASSY, 2P
Loading...