Sega 999-0921 User Manual
1st PRINTING APR 00
STD VERSION
OWNER’S MANUAL
SEGA ENTERPRISES, INC. USA
MANUAL NO. 999-0921
Warranty
Your new Sega Product is covered for a period of 90 days from the date of shipment. This certifies
that the Printed Circuit Boards, Power Supplies and Monitor are to be free of defects in workmanship or materials under normal operating conditions. This also certifies that all Interactive Control
Assemblies are to be free from defects in workmanship and materials under normal operating conditions. No other product in this machine is hereby covered.
Sellers sole liability in the event a warranted part described above fails shall be, at its option, to
replace or repair the defective part during the warranty period. For Warranty claims, contact your
Sega Distributor.
Should the Seller determine, by inspection that the product was caused by Accident, Misuse, Neglect, Alteration, Improper Repair, Installation or Testing, the warranty offered will be null and void.
Under no circumstances is the Seller responsible for any loss of profits, loss of use, or other damages.
This shall be the exclusive written Warranty of the original purchaser expressed in lieu of all other
warranties expressed or implied. Under no circumstance shall it extend beyond the period of time
listed above.
TABLE OF CONTENTS
INTRODUCTION OF THE OWNERS MANUAL
GENERAL PRECAUTIONS
1. PRECAUTIONS TO BE HEEDED FOR OPERATION
2. NAME OF PARTS
3. ACCESSORIES
4. ASSEMBLY AND INSTALLATION
5. PRECAUTIONS TO BE HEEDED WHEN MOVING MACHINE
6. CONTENTS OF GAME
7. EXPLANATION OF TEST AND DATA DISPLAY
7-1 SWITCH UNIT AND COIN METER
7-2 SYSTEM TEST MODE
A C.R.T. TEST
B COIN ASSIGNMENTS
7-3 GAME TEST MODE
A INPUT TEST
B OUTPUT TEST
C SOUND TEST
D VOLUME SETTING
E GAME ASSIGNMENTS
F
BOOKKEEPING
G BACKUP DATA CLEAR
8. HANDLE MECHA
8-1 REMOVING THE CONTROL MECHANISM
8-2 VOLUME ADJUSTMENT/REPLACEMENT
9. SHIFT LEVER
9-1 REMOVING THE SHIFT LEVER
9-2 SWITCH REPLACEMENT
10. ACCELERATOR & BRAKE
10-1 REMOVING THE ACCELERATOR AND THE BRAKE
10-2 ADJUSTING OR REPLACING THE VOLUME
10-3 GREASING
11. COIN SELECTOR
12. MONITOR
12-1 CAUTIONS/WARNINGS FOR HANDLING
12-2 CAUTIONS TO BE HEEDED WHEN CLEANING
12-3 ADJUSTMENT METHOD
13. REPLACEMENT OF FLUORESCENT LAMP AND BUTTONS
14. PERIODIC INSPECTION TABLE
15. TROUBLESHOOTING
16. GAME BOARD
16-1 LOCATING THE GAME BOARD
16-3 COMPOSITION OF THE GAME BOARD
18. DESIGN RELATED PARTS
19. PARTS LIST
20. WIRING DIAGRAMS
1
2~3
4~5
6
7~8
9~13
14
15~19
20~34
21
22~28
23
24~28
29~34
30
30
31
31
32
33
34
35~39
35~37
38~39
40~41
40
41
42~44
42
43~44
44
45~48
49~51
49~50
50
51
52~53
54
55
56~57
56
57
58
59~79
XXX
SPECIFICATIONS
Installation space: 34 in.(W) x 71 in.(D)
Height: 76 in.
Weight: Approx. 450 lbs.
Power maximum current: 5 Amp AC 120V 60 Hz
MONITOR: 29” COLOR MONITOR
INTRODUCTION OF THE OWNERS MANUAL
SEGA ENTERPRISES, LTD., has for more than 30 years been supplying various innovative and
popular amusement products to the world market. This Owners Manual is intended to provide
detailed descriptions together with all the necessary installation, game settings and parts ordering
information related to 18 WHEELER ‘AMERICAN PRO TRUCKER’ STD TYPE, a new SEGA
product.
This manual is intended for those who have knowledge of electricity and technical expertise, especially in ICs, CRTs, microprocessors, and circuit boards. Read this manual carefully to acquire
sufficient knowledge before working on the machine. Should there be a malfunction, non-technical
personnel should under no circumstances touch the interior system. Should the need arise, contact
our main office, or the closest branch office listed below.
SEGA ENTERPRISES, INC. (USA)
Customer Service
45133 Industrial Drive
Fremont, CA 94538
Phone 415-701-6580
Fax 415-701-6594
7:30 am - 4:00 pm, Pacific Standard Time
Monday thru Friday
General Precautions
Follow Instructions: All operating and use instructions should be followed.
Attachments: Do not use attachments not recommended by the product manufacturer as they may cause hazards.
Accessories: Do not place this product on an unstable cart, stand, tripod, bracket, or table. The product may fall,
causing serious injury to a child or adult, and serious damage to the product. Use only with a cart, stand, tripod, bracket, or
table recommended by the manufacturer, or sold with the product. Any mounting of the product should follow the
manufacturer’s instructions, and should use only mounting accessories recommended by the manufacturer.
Moving the Product: This product should be moved with care. Quick stops, excessive force, and uneven surfaces
may cause the product to overturn.
Ventilation: Slots and openings in the cabinet are provided for ventilation, to ensure reliable operation of the product
and to protect it from overheating; these openings must not be blocked or covered. The openings should never be blocked
by placing the product in a built-in installation such as a bookcase or rack unless proper ventilation is provided or the
manufacturer’s instructions have been adhered to.
Power Sources: This product should be operated only from the type of power source indicated on the marking label.
If you are not sure of the type of power supply to your location, consult your local power company. For products intended
to operate from battery power or other sources, refer to the operating instructions.
Grounding or Polarization: This product is equipped with a three-wire grounding-type plug, a plug having a third
(grounding) pin. This plug will only fit into a grounding-type power outlet. This is a safety feature. If you are unable to
insert the plug into the outlet, contact your electrician to replace your obsolete outlet. Do not defeat the safety purpose of the
grounding-type plug.
Power Cord Protection: Power-supply cords should be routed so that they are not likely to be walked on or pinched
by items placed upon or against them, paying particular attention to cords at plugs, convenience receptacles, and the point
where they exit from the product.
Overloading: Do not overload wall outlets, extension cords, or integral convenience receptacles as this can result in
a risk of fire or electric shock.
Object and Liquid Entry: Never push objects of any kind into this product through openings as they may touch
dangerous voltage points or short-out parts that could result in a fire or electric shock. Never spill liquid of any kind on the
product.
Servicing: Do not attempt to service this product yourself as opening or removing covers may expose you to danger-
ous voltage or other hazards. Refer all servicing to qualified service personnel.
Damage Requiring Service: Unplug this product from the wall outlet and refer servicing to qualified service person-
nel under the following conditions:
a) If the power cord or plug is damaged;
b) If liquid has been spilled, or objects have fallen into the product;
c) If the product has been exposed to rain or water;
d) If the product does not operate normally when following the operating instructions. Adjust only those controls that
are explained in the operating instructions. An improper adjustment of other controls may result in damage and will
often require extensive work by a qualified technician to restore the product to its normal operation;
e) If the product has been dropped or damaged in any way;
f) When the product exhibits a distinct change in performance; this indicates a need for service.
Replacement Parts: When replacement parts are required, be sure the service technician has used replacements parts
specified by the manufacturer or that have the same characteristics as the original part. Unauthorized substitutions may
result in fire, electric shock, or other hazards.
Safety Check: Upon completion of any service or repairs to this product, ask the service technician to perform safety
checks to determine that the product is in proper operating condition.
Heat: The product should be situated away from heat sources such as radiators, heat registers, stoves, or other prod-
ucts (including amplifiers) that produce heat.
Lithium Battery- Dispose of batteries only in accordance with the battery manufacturer’s recommendations.
Do not dispose in an open flame condition, since the battery may explode.
Cleaning: When cleaning the monitor glass, use water or glass cleaner and a soft cloth. Do not apply chemicals such
as benzine, thinner, etc.
Location: This an indoor game machine, DO NOT install it outside. To ensure proper usage, avoid installing indoors
in the places mentioned below:
• Places subject to rain/water leakage, or condensation due to humidity;
• In close proximity to a potential wet area;
• Locations receiving direct sunlight;
• Places close to heating units or hot air;
•In the vicinity of highly inflammable/volatile chemicals or hazardous matter;
• On sloped surfaces;
• In the vicinity of emergency response facilities such as fire exits and fire extinguishers;
• Places subject to any type of violent impact;
• Dusty places.
INSTALLATION PRECAUTIONS
• Verify the amperage of the branch circuit outlet before plugging in the power plug. Do not overload the circuit.
• Avoid using an extension cord. If one is required, use an extension cord of type SJT, 16/3 AWG
rated min. 120 VAC, 7A.
• Moving this unit requires a minimum clearance (of doors, etc.) of 32” (W) by 77” (H).
• For the operation of this machine, secure a minimum area of 32” (W) by 42”(D).
REGULATORY APPROVALS
This game has been tested and found to comply with the Federal Communications Commission Rules.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This
device may not cause harmful interference, and (2) this device must accept any interference received, including interference
that may cause undesired operation.
This game has been tested and listed by Underwriters Laboratories, Inc., to ANSI/UL22.
1 . PRECAUTIONS TO BE HEEDED FOR OPERATION
In order to prevent accidents, be sure to comply with the following points before and during operation.
PRECAUTIONS TO BE HEEDED FOR OPERATION BEFORE STARTING THE OPERATION
In order to avoid accidents, check the following before starting the operation:
Check if all of the adjusters are in contact with the surface. If they are not,
the cabinet can move and cause an accident.
Do not climb on the product. Climbing on the product can cause falling
accidents. To check the top portion of the product, use a step.
To avoid electric shock, check to see if door & cover parts are closed.
To avoid electric shock, short circuit and or parts damage, do not put the
following items on or in the periphery of the product:
Flower vases, flower pots, cups, water tanks, cosmetics, and receptacles/
containers/vessels containing chemicals and water.
To avoid injury, be sure to provide sufficient space by considering the
potentially crowded situation at the installation location. Insufficient installation space can cause the player to come into contact with or hit others
and result in injury or trouble.
PRECAUTIONS TO BE HEEDED DURING OPERATION
To avoid injury and accidents, those who fall under the following catagories are not
allowed to play the game:
* Intoxicated persons
* Those who have high blood pressure or heart problems.
* Those who have experienced muscle convulsion or loss of consciousness when
playing video games, etc.
* Persons susceptible to motion sickness.
* Persons whose acts runs counter to the products warning displays.
* Instruct those who wear high-heeled shoes to refrain from
playing the game by explaining that playing the game with highheeled shoes is very dangerous and likely to cause a potentially
hazardous situation.
To avoid electric shock and short circuit, do not allow customers to put hands and
fingers or extraneous matter in openings of the product or small openings in or around
doors.
To avoid electric shock and short circuit, do not allow the customers to unplug the
power plug without a justifiable reason.
Although this product has the accident preventive covering attached to potentially
hazardous places where hand and fingers could be caught, small children are unable to
perceive hazards. Use care so that small children do not come close to the product when
in play.
Immediately stop such violent acts as hitting and kicking the product. Such violent acts
can cause parts damage and/or falling down, resulting in injury due to fragments and
falling down.
2 . NAME OF PARTS
GAME SPECIFICATIONS
DURING SHIPPING
WHEN ASSEMBLED
WIDTH in. LENGTH in. HEIGHT in.
All measurements are and rounded UP
40” X 77” X 84”
34” X 71” X 76”
WEIGHT lbs.
500 LBS.
450 LBS.
3 . ACCESSORIES
THE SHIPMENT METHOD DESCRIBED BELOW ONLY
APPLIES TO ‘MODEL 3’ BOARDS CONTAINED IN THE
FOLLOWING GAMES:
LOST WORLD, VIRTUA FIGHTER 3, SUPER GT, SEGA BASS FISHING, STRIKER 2
HARLEY DAVIDSON, RALLY 2, DAYTONA 2, DIRT DEVILS, HOUSE OF THE DEAD
2, OCEAN HUNTER, STAR WARS TRILOGY, ZOMBIE REVENGE, CRAZY TAXI,
ARILINE PILOTS, 18 WHEELER
!!!!NNEEVVEERR SSHHIIPP MMOODDEELL 33 // NNAAOOMMII GGAAMME
BBOOAARRDDSS OOUUTTSSIIDDEE OOFF CCAAGGEE!!!
CARTON BOX
601-8928 (1)
Used for transporting the GAME BOARD.
{SUPPLIED WITH YOUR GAME}
DO NOT SHIP GAME BOARD WITHOUT
THIS BOX AS IT MAY DAMAGE THE GAME
BOARD AND VOID YOUR WARRANTY.
“CHECK SIDE” Display
FILTER BOARD
!
E
NO OTHER GAMES BOARDS ARE TO BE SHIPPED IN THE CAGE AS
THEY MAY BE DAMAGED BEYOND REPAIR. PLEASE SHIP THEM
WITHOUT CAGE PROPERLY PROTECTED DURING SHIPPING.
4 . ASSEMBLING AND INSTALLATION
•Assembling should be performed as per this manual. Since this is a
complex machine, erroneous assembling may cause damage to the
machine, or malfunctioning to occur.
•When assembling, be sure to perform work by plural persons.
Depending on the assembly work, there are some cases in which
a single person performing the work can cause personal injury
or parts damage.
•Be careful so as not to damage wirings. Damaged wiring can cause
electric shock and short circuit hazards.
When carrying out the assembly work, follow the procedure in the following 5-item sequence:
1
ASSY OF THE CABINET
2
SECURING IN PLACE (ADJUSTER ADJUSTMENT)
3
POWER SUPPLY
ASSEMBLING CHECK
4
Note that the tools such as a phillips screwdriver and wrench for M16 hexagon bolt w/24 mm width
across flats are required for the assembly work.
ASSY OF CABINET
1
Permanantly tightening the hex bolts should not be completed until
the leg levelers are adjusted properly.
NOTE: Game is shipped fully assembled. No assembly required.
SECURING IN PLACE (ADJUSTER ADJUSTMENT)
2
Be sure to have all the Adjusters make contact with the floor surface.
Unless the Adjusters come into contact with the floor surface, the
Cabinet can move of itself, causing an accident.
This machine has 4 each of casters and adjusters (shown below). When the installation position is determined, cause
the adjusters to come into contact with the floor directly, make adjustments in a manner so that the casters will be
raised approximately 5mm. from the floor and make sure that the machine position is level.
1
Move the machine to the installation position.
Be sure to provide adequate space allowing the
player to get on and off.
2
Have all of the Leg Adjusters make contact
with the floor. Adjust the height of the Leg
Adjusters by using a wrench so that the
machine's position is kept level.
3
After making adjustments, fasten the leg
Adjuster Nut upward and secure the height of
the Leg Adjuster.
POWER SUPPLY
3
Ensure that the power cord is not exposed on the surface (passage,
etc.). If exposed, they can be caught and are susceptible to damage.
If damaged, the cord can cause an electric shock or short circuit.
Ensure that the wiring position is not in the customer's passage way
or the wiring has protective covering.
Connect the game to the power supply and turn on power to the game. Before connecting power supply be sure that
power switch is off
1
Turning the AC unit’s main switch on will cause the machine
to start the power check and network check automatically.
2
In the Power On check, the steering wheel turns left and right,
and then returns to the centering position and stops. In this
check, the values of the VR inside the control panel are
corrected.
3
Until this check is finished, and the steering wheel stops, do
not touch the steering wheel or play the game.
If you do, the steering reaction during the game (reaction at
the time of course-out or crash) can not be obtained correctly.
In the case of an abnormal reaction during the game, turn
power on again from the beginning and complete the power on
check.
ASSEMBLING CHECK
4
In the TEST MODE, ascertain that the assembly has been made correctly and that the IC BOARD is
satisfactory.
In the test mode, perform the following test:
(1) MEMORY TEST
MEMORY TEST MODE
RAM TEST
IC29 GOOD
IC34 GOOD
IC16 GOOD IC18 GOOD
IC20 GOOD IC22 GOOD
IC9 GOOD IC10 GOOD
IC11 GOOD IC12 GOOD
PRESS TEST BUTTON TO EXIT
(2) C.R.T. TEST
C.R.T. TEST 1/2
RED
GREEN
BLUE
WHITE
Selecting the RAM TEST item on the test mode
menu screen causes the on-board memory to be
tested automatically. The game board is satisfactory if the display beside each IC No. shows
GOOD.
In the TEST mode menu, selecting C.R.T. TEST
allows the screen (on which the monitor is tested)
to be displayed. Although the monitor adjustments
have been made at the time of shipment from the
factory, color deviation, etc., may occur due to the
effects of geomagnetism, the location of the
building’s steel frames and other game machines
in the periphery. By watching the test mode
screen, make judgement as to whether an adjustment is needed. If it is neccessary, adjust the
monitor by refering to Chapter 12.
PRESS TEST BUTTON TO CONTINUE
C.R.T. TEST 2/2
PRESS TEST BUTTON TO EXIT
(3) INPUT TEST
INPUT TEST
COIN CHUTE #1 OFF
COIN CHUTE #2 OFF
SERVICE OFF
TEST OFF
START OFF
VIEW OFF
HORN OFF
SHIFT [L] OFF
SHIFT [H] OFF
SHIFT [R] OFF
HANDLE XXH
ACCEL XXH
BRAKE XXH
PRESS TEST + SERVICE BUTTON TO EXIT
(4) OUTPUT TEST
Selecting the INPUT TEST on the test mode
menu screen carses the screen (on which each
switch is tested) to be displayed. Press each
switch. For the coin switch test, insert a coin
into the coin inlet with the coin chute door
open. If the display beside each switch indicates “ON,” the switch and wiring connections
are satisfactory.
START LAMP OFF
VIEW LAMP OFF
HORN LAMP OFF
ROLL LEFT OFF
ROLL RIGHT OFF
->EXIT
SELECT WITH SERVICE BUTTON
AND PRESS TEST BUTTON
(5) SOUND TEST
B.G.M. 0/ XX
EFFECT 0/ XX
[ ]
ICS 0/ XX
[ ]
-> EXIT
OUTPUT TEST
SOUND TEST
Select OUTPUT TEST from the menu in the
test mode to cause the screen (on which each
lamp and wiring connection is tested) to
appear. Ensure that each lamp lights up satisfactorily.
In the TEST mode, selecting SOUND TEST
causes the screen, on which sound related BD
and wiring connections are tested, to be
displayed. Be sure to check if the sound is
satisfactorily emitted from each speaker and
that the sound volume is appropriate.
SELECT WITH SERVICE BUTTON
AND PRESS TEST BUTTON
Perform the above inspections also at the time of monthly inspection.
5 . PRECATIONS TO BE HEEDED WHEN MOVING THE MACHINE
When moving the machine, be sure to pull out the plug from
the power supply. Moving the machine with the plug inserted
can damage the power cord and cause a fire or electric shock.
When moving the machine on the floor, retract the Adjusters
and ensure that Casters make contact with the floor. During
transportation, pay careful attention so that Casters do not
tread power cords. Damaging the power cords can cause an
electric shock and/or short circuit.
When lifting the cabinet, be sure to hold the catch portions or
bottom part. Lifting the cabinet by holding other portions can
damage parts and installation portions, due to the empty
weight of the cabinet, and cause personal injury.
Do not push on the plastic parts. Doing so may damage the parts
and cause injury due to fragments resulting from damage.
6 . CONTENTS OF GAME
The following explanations apply in the event the product is functioning satisfactorily. Should there be any
moves different from the following contents, some sort of faults may have occured. Immediately look into
the cause of the fault and eliminate the cause thereof to ensure satisfactory operation.
When the product is energized, the Billboard’s fluorescent lamp is always lit. During the advertise mode, the
advertise screen is shown on the monitor and sound is emitted from the speakers. Setting to No Sound
Output during the advertise mofr is possible in the TEST mode.
OUTLINE OF THE GAME
This is a single, driving game in which the player competes with rivals by driving a Trailer Truck to cross
America.
When coins are inserted to gain credits, the START button starts flashing. Press the START button to
proceed to the SELECTOR mode where you can select your truck and the trailer. The game starts upon
selecting the truck and the trailer.
Based on the setting made in the test mode, the number of coins inserted to obtain a credit counts as one
credit in this product. The number of credits necessary to start the game and to continue the game can be set
in the test mode.
The game consists of the 4 kinds of driving stages and 3 kinds of parking stages (Bonus stages).
When continued, the game is played at the beginning of the last stage that resulted in a game over.
If your score falls within the top 5, you can enter your name.
CONTENTS OF THE GAME
Pass the checking point within a certain period of time and reach the goal, and you can clear the stage.
The game finishes after clearing all 4 stages.
If you can reach the goal ahead of your rival trailers in each stage (the 1st through the 3rd), then you can
play the Parking game (Bonus game).
GAME OVER
If you fail to pass the checking point within a certain period of time or fail to goal, the game is over.
Passing the checking point behind the rival trailers or failing on the Parking game does not result in a game
over.
OPERATION
<STEERING WHEEL>
SELECTOR : Turn right or left to select an object.
GAME PLAY : Operate the Trailer Truck.
<HORN AT THE DRIVER’S SEAT>
SELECTOR : Decide
GAME PLAY : Blow the horn to signal the car ahead to move out of the way or to have it increase
the speed. Have the trailer ahead increase the speed.
<ACCEL.>
SELECTOR : Decide
GAME PLAY : Increase your Trailer Truck speed, or stop it.
<BRAKE>
SELECTOR : Void
GAME PLAY : Decrease your Trailer Truck speed, or stop it.
<GEAR>
SELECTOR : Void
GAME PLAY : 3-position, HI (High), LOW, R (Reverse)
<VIEW CHANGE>
SELECTOR : Void
GAME PLAY : Select either Driver’s View or Bird’s View.
<START BUTTON>
The START button flashes when the number of coins that are worth one credit are inserted. While
flashing, press the START button to proceed to the SELECTOR. It also flashes when one or more
credit(s) remains after the game is over.
SELECTOR
TRUCK SELECT
Select the truck from among ASPHALT COWBOY, STREAMLINE, HIGHWAY CAT, LONG HORN, and
NIHONMARU. Each truck’s abilities in SPEED, TORQUE, and TOUGHNESS differ.
TRAILER SELECT
When starting in stage 2, 3, or 4, select the trailer for towing from the 2 trailers. The weight, the length,
and the transportation fee differ. The heavier the trailer, the more the difficulty.
NAME ENTRY
If your score falls within the top 5, you can enter your name.
VIEWING THE GAME SCREEN
DESTINATION
TIME LIMIT
REARVIEW MIRROR
TRANSPORTATION
FEE
GEAR CONDITION
GEAR CHANGE
INDICATOR
TACHOMETER
<DESTINATION>
Name of the destination point.
<TIME LIMIT>
Indicates the player’s playable time. Additional time will be added when passing the CHECKPOINT
and obtaining TIME BONUS.
<REARVIEW MIRROR>
Indicates the rear condition while the DRIVER’S VIEW is selected.
<TRANSPORTATION FEE>
Indicates the fee you receive when you reach the destination. If you damage the trailer by hitting
another car, etc., the fee will be reduced.
<TACHOMETER>
Indicates the speed of rotation.
<GEAR CHANGE INDICATOR>
Indicates the gear condition (4 positions total) with the lamp on the monitor.
<GEAR CONDITION>
Indicates the current gear condition. The three types of gears (REVERSE - LOW - HI) are avail
able.
7 . EXPLANATION OF TEST AND DATA DISPLAY
By operating the switch unit, periodically perform the tests and data check. When installing
the machine initially or collecting cash, or when the machine does not function correctly,
perform checks in accordance with the explanations given in this section. The following
shows tests and modes that should be utilized as applicable.
A NAOMI GAME BOARD is used for this product. This game board system allows
another game board to be played by replacing the ROM Board Case mounted on the
NAOMI CASE. As such, the test mode of this system consists of the System Test Mode for
the system to execute SELF-TEST, COIN ASSIGNMENTS, etc. used in common for the
machines employing the NOMI BOARD, and the Game Test Mode for the specific product
to execute Input/Output test for the operation equipment, difficulty setting, etc. In this
manual, explanations regarding the System Test Mode cover the settings for this product
only. For the details of the System Test Mode, refer to the NAOMI SERVICE MANUAL.
TABLE EXPLANATION OF TEST MODE
ITEMS DESCRIPTION CHAPTERS
When the machine is installed, perform the following:
INSTALLATION
OF MACHINE
MEMORY
PERIODIC
SERVICING
CONTROL
SYSTEM
MONITOR
1. Verify that each setting is per the standard settings at the
time of shipment.
2. Check all Input equipment in the INPUT TEST mode.
3. Check all OUTPUT equipment in the OUTPUT TEST mode.
4. In the MEMORY TEST mode, check ICs on the IC Board.
This test is automatically executed by selecting RAM TEST or ROM
BOARD TEST in the Menu mode.
Periodically perform the following:
1. MEMORY TEST
2. Ascertain each setting.
3. Test all Input equipment in the INPUT TEST mode.
4. Test all Output equipment in the OUTPUT TEST mode.
1. Check all Input equipment in the INPUT TEST mode.
2. Adjust or replace all Input equipment.
3. If the problem remains unsolved, check the movement of each
control mechanism.
In the MONITOR ADJUSTMENT mode, check to see if the
MONITOR adjustment is appropriately made.
SERVICE MANUAL
7 - 3A
7 - 3B
4-1
SERVICE MANUAL
SERVICE MANUAL
4-1
4-1
7 - 3A
7 - 3B
SERVICE MANUAL
7 -3 B, F
1 0, 1 1 , 1 2
SERVICE MANUAL
12
IC BOARD
DATA CHECK
1. MEMORY TEST
2. In the SOUND TEST mode, check the sound related ROMs.
Check such data as game play time and histogram to adjust the
difficulty level, etc
SERVICE MANUAL
4 - 1 , 7 - 3C
SERVICE MANUAL
7 -3 F
7 - 1 SWITCH UNIT AND COIN METER
Never touch places other than those specified. Touching places not
specified can cause electric shock and short circuit.
Adjust to the optimum sound volume by considering the environmental
requirements of the installation location.
If the COIN METER and the game board are electrically disconnected,
game play is not possible.
Open the COIN CHUTE DOOR, and the switch unit shown will appear. The
function of each switch is as follows:
SWITCH UNIT
SPEAKER VOLUME (SPEAKERS)
1
Controls the sound volume for the left/right CONTROL PANEL speakers.
SPEAKER VOLUME (SUPER WOOFER)
2
Controls the sound volume for the SUPER WOOFER and the BASE SHAKER under the seat.
TEST BUTTON (TEST SW)
3
Enters to the test mode.
SERVICE BUTTON (SERVICE SW)
4
Gives credits without registering on the coin meter.
COIN METER
Open the Cashbox Door by using the key to
have the Coin Meter appear underneath the
Cashbox.
7 - 2 SYSTEM TEST MODE
•The contents of settings changed in the TEST mode are stored when the TEST
mode is finished from EXIT in the MENU mode. If the power is turned off before the
TEST mode is finished, the contents of the setting changes do not take effect.
•Executing “BACKUP DATA CLEAR” in the SYSTEM TEST MODE does not clear the
BOOKKEEPING data in the GAME TEST MODE.
•Entering the TEST mode clears fractional numbers of coins less than one credit and
BONUS ADDER data.
The SYSTEM TEST mode mainly allows checks of the IC Board for accurate functioning , monitor adjustment, as well
as CRT TEST and COIN ASSIGNMENTS, etc. The following assignments, however, should be designated for this
product.
♦ CABINET TYPE : 1 PLAYER (S)
♦ MONITOR TYPE : HORIZONTAL
♦ SERVICE TYPE : COMMON
♦ COIN CHUTE TYPE : COMMON
TEST ITEM SELECT
SYSTEM MENU
RAM TEST
JVS TEST
SOUND TEST
C.R.T. TEST
SYSTEM ASSIGNMENTS
COIN ASSIGNMENTS
BOOKKEEPING
BACKUP DATA CLEAR
CLOCK SETTING
ROM BOARD TEST
GAME TEST MODE
[18 WHEELER]
->EXIT
SELECT WITH SERVICE BUTTON
AND PRESS TEST BUTTON
1
After turning the power on, press the TEST button to display the test item menu shown above.
2
Press the SERVICE button to move the arrow to the desired item and press the TEST button.
3
When finished, bring the arrow to EXIT and press the TEST button to return to the Game mode.
A C.R.T. TEST
1) RGB COLOR ADJUSTMENT SCREEN
In this screen, monitor color can be checked.
C.R.T. TEST 1/2
1 32
RED
GREEN
BLUE
WHITE
PRESS TEST BUTTON TO CONTINUE
2) MONITOR SIZE ADJUSTMENT SCREEN
In this screen, monitor size can be checked.
C.R.T. TEST 2/2
Each of red, green, and blue is the darkest at the
leftmost end, and becomes brighter towards the
right-hand end in 31 gradiations. Monitor brightness
is satisfactory if the white color bar is black at the
left end and if it is white at the right end.
Press the TEST button to proceed to the next screen.
Adjust the crosshatch frame line so that the checkered pattern does not extend beyond the screen.
Press the TEST button to return to the menu mode.
PRESS TEST BUTTON TO EXIT
Loading...