Sealer Sales SS-1519LMC User Manual

SS-Series Economy L-Bar Sealers Model: SS-1519L, SS-1519LM, SS-1519LMC
Distributed By:
Version 1.0 Last Updated: 2/20/20
Sealer Sales | www.sealersales.com | Tel: 818-718-8818 | E-mail: contact@sealersales.com
Copyright © 2019 by Stephanie Hwang
All rights reserved. No part of this publication may be reproduced, distributed, or transmitted in any form or by any means, including photocopying, recording, or other electronic or mechanical methods, without the prior written permission of the publisher, except in the case of brief quotations embodied in critical reviews and certain other noncommercial uses permitted by copyright law. For permission requests, write to the publisher, addressed “Attention: Permissions Coordinator,” at the address below.
Sealer Sales, Inc. 8820 Baird Avenue Northridge, Ca 91324 www.sealersales.com
Printed in the United States of America
Sealer Sales | www.sealersales.com | Tel: 818-718-8818 | E-mail: contact@sealersales.com
2
IMPORTANT - PLEASE READ THIS CAREFULLY
The development of a good safety program, that is rigidly enforced, is absolutely imperative when involved in the operation of industrial equipment. Our machinery is well designed and includes extremely important safety features. The part you the user play through proper installation and maintenance procedures is of far greater significance than our designs. Only properly trained individuals following rigidly enforced safety rules, as recommended by A.N.S.I. and O.S.H.A., should be allowed to operate these machines.
TABLE OF CONTENTS
___________________________________________________________
Preface
Unpacking 4-6 Warranty Notice 7 Warranty 8-9 Warranty Exceptions 10 Warnings 11-13
L-Bar Sealer Section
Description and Specifications 14 Installation and Basic Set-Up 15-20 Film Threading Diagram 21 Sequence of Operation 22-26
Troubleshooting -- L-Bar Sealer Maintenance – L-Bar Sealer
27-40 41-51
3
Electrical Schematic NOTICE! 52
Electrical Schematic Model SS-1519L Electrical Schematic Model SS-1519LM Electrical Schematic Model SS-1519LMC
53 54 55
Parts Nomenclature 56 Replacement Parts List -- Sealer 57-58 Spare Parts List 59
4
UNPACKING
THOROUGHLY INSPECT EQUIPMENT UPON ARRIVAL.
If goods are received short or in a damaged condition, it
is important that you notify the carrier’s driver before he leaves your company and insist on a notation of the loss or damage
across the face of the freight bill. Unless this is done, no claim can be enforced against the transportation company.
If concealed loss or damage is discovered, notify the carrier at once and insist on an inspection. This is absolutely necessary! A concealed damage report must be made no later than five (5) days from the date the shipment was delivered. Unless you do this, the carrier will not consider any claim for loss or damage.
The carrier’s agent will then make an inspection and grant a
concealed damage notation. If you give the transportation company a clear receipt for the goods that have been damaged or lost in transit, you do so at your own risk and expense.
All claims must be filed within 5 days of delivery date or carrier will not accept them.
Sealer Sales is willing to assist in every possible manner to collect claims for loss or damage; however, this does not hold Sealer Sales responsible for collection on claims or replacement of material.
Do not throw away damaged pallets or box until freight inspection has occurred.
UNPACKING
Your new Model SS-1519L Series L-Bar Sealer comes in
a tri-walled corrugated box to protect it.
1. If your machine does not arrive in good condition, write on
shipping paperwork that outside of box is damaged. Concealed damage may have occurred.
2. Remove stretch film and Poly Bag covering machine.
5
3. Remove film rack from under L-Bar Sealer.
4. Check film rack. You should have
(a) (1) Film Rack (b) (1) adjustable center knob
(c) (2) film roll guides
UNPACKING
5. Mount film rack on right side at end of machine and slid left.
This is a boltless mounting system, No Tools Required!.
6
6. Place in desired location and use locking knob in center to set
in place.
UNPACKING
7
IMPORTANT WARRANTY NOTICES
OPERATING AND MAINTENANCE MANUAL
The operating and maintenance manual has been carefully prepared to provide the user with all the information needed to properly install, operate, and maintain your Sealer Sales equipment.
Please read this manual carefully and refer to it for information on the care and use of your Sealer Sales equipment. It is recommended that additional copies be ordered for use by production, maintenance, and supervisory personnel. Although the design of this equipment incorporates safeguards to protect personnel, care should be used in operating, adjusting, and servicing.
Attention is directed to the warranty that accompanies all your Sealer Sales equipment. The terms and conditions of this warranty apply only to unmodified units. Any
unauthorized modifications to the equipment automatically voids this warranty.
Sealer Sales provides a two-year warranty on parts,
excluding shipping or freight costs for replacement parts. All warranty parts are shipped F.O.B. Rancho Cucamonga, California.
WARRANTY NOTICE
8
Sealer Sales
WARRANTY
Sealer Sales, Inc. warrants each new product manufactured to be free from defects in material and workmanship for a period of (1) year from date of shipment by Sealer Sales.
This warranty is not transferable with any subsequent resale.
Defective parts under warranty must be returned to Sealer Sales freight prepaid. Sealer Salessole obligation
and purchaser’s sole remedy in the event of a warranty dispute shall be, at Sealer Sales' option, to repair or replace the part in
question. Labor incurred in removing or installing the defective part is not covered by this warranty. Prior to returning any parts for any reason, contact Sealer Sales for a Return Authorization Number. This number must accompany all returns.
This warranty shall not apply if equipment has been tampered with, misused, improperly installed, altered, or has received damage due to abuse, carelessness, accident or failure to follow recommended regular maintenance procedures or has been serviced by someone other than a duly authorized factory representative without the express written consent of Sealer Sales, Inc.
This warranty is in lieu of all other warranties, expressed or implied, including but not limited to warranties of merchantability and fitness for a particular purpose, non-infringement or any other matter.
Sealer Sales shall have no liability to any person for direct, indirect, incidental or consequential damages or delay resulting from any defect negligence, or tort and customer hereby waives for itself
WARRANTY
9
any and all claims for punitive damages and all claims of negligence of strict liability or both. In no event shall our liability exceed the purchase price of the product that was actually paid.
Sealer Sales reserves the right to make changes, additions, or improvements to our products with no obligation to make such changes in any previously shipped product covered by this warranty.
Sealer Sales shall not be held liable for any damages arising out of nor in connection with the operation of the equipment should customer or its agent fail to maintain equipment in safe operating condition. This warranty shall become unenforceable if and to the extent the customer or its agents remove, disconnect, or otherwise render useless any safety device and or parts designed or affixed by us or fails to maintain and service equipment in a manner as advised.
Sealer Sales provides a one-year warranty on parts, excluding shipping or freight costs for replacement parts. All warranty parts are shipped F.O.B. Rancho Cucamonga, California. Service Labor to install part is not covered under warranty!
WARRANTY
10
WARRANTY EXCEPTIONS
The following parts are an exception to the general warranty list on page 10. Each part listed below shall carry a 30-day warranty unless designated otherwise.
SS-1519L Series Sealer Parts
1. Fuses
2. Conveyor Belt (Optional)
The following sealer parts are considered to be consumable
and not under warranty:
1. Silicone Sponge
2. Band Ribbon
3. PTFE Tapes
4. Transite Channels
WARRANTY EXCEPTIONS
11
WARNINGS
Every effort has been taken to ensure your safety while operating this machine; however, there still remain certain risks. Do not allow this machine to be operated before informing all personnel of the following warnings.
WARNING........
Do not tamper with the electrical wiring. Only use a licensed electrician for maintenance. Always disconnect the electrical power before attempting any maintenance to all electrical and/or moving parts.
WARNING........
In order to prevent injury to personnel and/or machinery DO NOT INCREASE SETTINGS OR RATINGS ON EITHER ELECTRICAL OR MECHANICAL OVERLOAD SAFETY DEVICES.
WARNING........
KEEP HANDS AWAY FROM MOVING CONVEYORS AND ASSEMBLIES. Conveyor belts that have become worn or frayed are capable of being hazardous. They should be replaced promptly.
WARNING........
NEVER OPERATE THIS OR ANY MOVING EQUIPMENT WITHOUT ALL COVERS AND GUARDS IN PLACE. The internal mechanism of most packaging machinery contains numerous shear, pinch, and inrunning nip points, many of which are capable of causing severe injury and/or permanent disfigurement.
WARNINGS
12
WARNING........
To minimize the potential for personnel injury, always be sure that machine operators and others working on the machinery are properly trained in the correct usage of the equipment and properly instructed regarding the safety procedures for operation.
WARNING........
Heat sealing arms and jaws on packaging machinery can become very warm after a period of use. KEEP HANDS AWAY WHILE IN OPERATION AND USE CAUTION IF THE MACHINE HAS BEEN RUNNING RECENTLY.
WARNING........
ANY MODIFICATIONS TO EITHER THE ELECTRICAL CIRCUITRY OR THE MECHANICAL ASSEMBLIES OF THE MACHINERY WILL VOID ANY WARRANTIES ASSOCIATED WITH THIS EQUIPMENT. Such modifications may introduce hazards that would not otherwise be associated with this machinery. Sealer Sales will not be responsible for any consequences resulting from such unauthorized modifications.
WARNING........
The use of certain types of plastic films in sealing and/or shrinking equipment may result in the release of HAZARDOUS FUMES due to the degradation of the film at high temperatures. Before using any plastic film in this equipment, the manufacturer or supplier of the film should be contacted for specific information concerning the potential release of hazardous fumes. ADEQUATE VENTILATION MUST BE PROVIDED AT ALL TIMES.
WARNING........
It is important that the machine operator unplug the machine when he/she has finished operating the unit.
WARNINGS
WARNING........
Turn off machine and disconnect power cord from power source before attempting to work on machine.
13
WARNINGS
14
DESCRIPTION AND SPECIFICATIONS OF
MODEL SS-1519L SERIES L-Bar Sealer
DESCRIPTION
The purpose of a SS-1519L Series is for low to medium volume packaging requiring excellent seals and minimal maintenance. It features an impulse mode for sealing of films. This model incorporates an optional electromagnetic hold-down system, allowing the operator to load another package while the preceding package is being sealed. This system provides consistent seals. In addition, an optional package take-away conveyor increases production speed by automatically discharging product into a shrink tunnel.
SPECIFICATIONS
Model: Seal Area:
Machine Size:
Volts: Amperage: Weight:
SS-1519L
Series Length: 19 Width: 15” Length: 53 Width: 24” Height: 45 110 20 150 lbs.
SPECIFICATIONS
15
INSTALLATION AND BASIC SET-
UP OF L-Bar Sealer
IMPORTANT
Read this manual carefully, and make it available to everyone connected with the supervision, maintenance, or production of this machine. Additional copies are available at your request. (Contact your distributor for this information.) Be very careful when operating, adjusting, or servicing this equipment. If in doubt, stop and obtain qualified help before proceeding.
INSTALLATION OF SS-1519L SERIES L’ SEALERS
Place the SS-1519L in the desired location with the required electrical power source available. (See power requirements.) Make certain that proper electrical wiring is provided to guard against low voltage. If the voltage is too low, the equipment will not function properly. Machine comes complete with power cord and 110 volt plug.
Finding the proper location is a most important function of the initial set-up. One must take several factors into consideration:
INSTALLATION
16
1. Adequate power source.
2. Relationship to source of product.
3. Relationship to L-Bar Sealer.
4. Relationship to any conveyors necessary to remove
finished product.
5. Convenience of operator.
Make sure to connect machine to an Independent Power Source. DO NOT run any other equipment on the same power
line as your machine.
Do not attempt to install, adjust, or operate this machine without first reading the contents of this manual. Although the design of the equipment incorporates safeguards to protect operating and maintenance personnel, care should be used in operating, adjusting, and servicing.
INSTALLING FILM RACK
IMPORTANT: Remove film rack from under sealer and
install at the end of the sealer on the right hand side with the four bolts and center knob provided. Mounting holes are slotted for adjustment, set film rack flush with backside of the machine frame.
INSTALLATION
17
MOUNTING FILM
Select the proper width of centerfold film for the item being packaged, allowing for width and height of package. With the package properly positioned within the film in the sealing area, allow sufficient film to overlap the sealing bars so that a seal may readily be made without any possibility of open areas due to insufficient film.
Place film roll on cradle mount film rack. The centerfold is to be placed away from the operator, toward the rear of the machine. Use core chucks to position film roll on rack and tighten film guide nuts to hold film roll in position.
PIN PERFORATOR
Located between the lower idler rollers, the pin perforator creates holes for air escape as the operator pulls on the film. This allows the air to escape as the package travels through the tunnel.
INSTALLATION
Loading...
+ 42 hidden pages