Sealer Sales FKR-200A, FKR-300A, FKR-400A User Manual

Double Impulse Portable Sealers
Model: FKR-200A, FKR-300A, FKR-400A

Distributed By:

Version 1.0
Last Updated: 2/15/19

Copyright © 2019 by Stephanie Hwang

All rights reserved. No part of this publication may be reproduced, distributed, or transmitted in any form or by any means, including photocopying,
recording, or other electronic or mechanical methods, without the prior written permission of the publisher, except in the case of brief quotations
embodied in critical reviews and certain other noncommercial uses permitted by copyright law. For permission requests, write to the publisher,
addressed “Attention: Permissions Coordinator,” at the address below.

Sealer Sales, Inc.
8820 Baird Avenue
Northridge, Ca 91324
www.sealersales.com

Printed in the United States of America

F K R - A I N S T R U C T I O N M A N U A L

1

E Q U I P M E N T I N F O R M A T I O N

 Model #

 Serial #

 Purchase Date:

 Reference # (found on packing slip)

 Owner:

General Information

Thank you for purchasing our FKR-A Series Double Impulse Portable Sealers.

This owner’s manual contains information relating to your sealer. The manual will provide you
with basic information concerning both operation and maintenance of your new machine. Please
read it carefully as failure to do so may result in bodily injury and/or damage to the equipment.

Please fill in the information below. You will find the information on the machine identification
plate. You will need this information when ordering replacement parts or making technical
inquiries.

No part of this manual may be duplicated, reproduced, stored in a retrieval system, translated,
transcribed, or transmitted in any form without the express prior written permission of Sealer Sales.

F K R - A I N S T R U C T I O N M A N U A L

2

Safety Instructions

WARNING!

Below are general safety precautions and warnings that should be

understood prior to setting up or operating your equipment. Read and fully understand all instructions and
warnings prior to using this unit. Your safety is most important! Failure to comply with procedures may
result in serious injury or property damage. Remember:

responsibility.

Unsafe practices or unauthorized modifications could result in accidents or property damage. Failure to
follow these safety rules and take necessary precautions can result in serious injury as well as damage to
equipment.

 Never operate or service your sealer until you have read this manual completely and understand it

fully.

 Plug the sealer into a standard 120 Volt, 60Hz wall outlet or surge protector.
 Do not use the sealer if the power cord, plug or any other parts are damaged. Be sure not to allow

the power cord to drape into your work area. Check that all parts are operating properly and
perform the intended functions. Check for any worn parts before starting operation. Check for all
other conditions that may affect the operation.

 Reduce risk of unintentional starting. Make sure the power switch is in the "OFF" position before

connecting to the power source.

Your personal safety is your

 Always disconnect sealer from power source before servicing, changing accessories or cleaning the

unit.

 To provide protection against the risk of electrical shock, the power connection must be properly

grounded at all times.

 Do not leave the sealer unattended when in use. Disconnect the sealer from the power source

before leaving the work area.

 Sealer is used solely for sealing thermoplastic materials. Using the machine for any other purpose

can cause damage to the machine and operator.

 While operating machinery, wear close-fitting clothing and tie back long hair to prevent any

external items from getting caught in the machine. Do not wear jewelry when operating the sealer.

F K R - A I N S T R U C T I O N M A N U A L

3



Never touch the heating element(s) with bare hand while the sealer is plugged into a power source,
in operation or just finished operation. Touching heated areas may cause fire and/or severe burns.

 While machine is in operation, do not place fingers, tools, or other foreign objects on or into the

machine. Do not place hands or fingers near pinch points. Do not touch machine while it is in
operation. Perform all procedures carefully and watch where hands and fingers are at all times.

 The sealer is not water resistant or water proof. Spraying down the machine will damage machine

or cause electrical shock. Do not submerge the sealer into water or liquid.

 Do not operate sealer in a corrosive or humid environment.

 Always keep the machine clean, lubricated and in good working condition. Follow any

maintenance and lubrication procedures outlined in this manual. Make sure unit is disconnected
from power source before cleaning.

 NEVER use any accessories or parts from other manufacturers. Machine should not be altered or

modified using parts that are not genuine authorized parts. Doing so will VOID YOUR
WARRANTY.



When replacing the heating elements, always replace the PTFE adhesive under the
heating element. A worn PTFE adhesive can cause the heating element to break.

PTFE adhesive works as a barrier between the body of the sealer and the element. Never allow
the element to come in direct contact with the sealer body as that will damage the timer.

 Never leave the sealer unattended. Be safe, disconnect the sealer from power source before

leaving work area.

 Always keep out of reach of children and pets.
 Close supervision is necessary when any appliance is near persons with reduced physical, sensory

or mental capabilities or lack of experience and knowledge . This sealer is NOT to be used by
children or by persons with reduced physical, sensory or mental capabilities or lack of experience
and knowledge.

 DO NOT use the sealer outdoors.
 DO NOT use the sealer while under the influence of drugs, medications or alcohol.

SAVE THESE INSTRUCTIONS - REFER TO THEM OFTEN AND USE THEM TO INSTRUCT

OTHERS.

The