SEA Gate 1 24V DC Service manual
GB
Sistemi Elettronici
di Apertura Porte e Cancelli
International registered trademark n. 804888
®
SEA S.r.l.
DIREZIONE E STABILIMENTO:
Zona industriale 64020 S.ATTO Teramo - (ITALY)
Tel. 0861 588341 r.a. Fax 0861 588344
GATE 1 24V DC
CONTROL UNIT
http://www.seateam.com
e-mail:seacom@seateam.com (Uff. Comm.le)
seatec@seateam.com (Uff. Tecnico)
English
1 2 3 4 5 6 7 8 9 10
1 2 3
CN2CN2
P1P1
CN3CN3
LE
D
1
L
E
D
2
L
ED
3
LE
1 2 3 4 5 6
CN4CN4
LED1 = Photocell
LED2 = Safety edge
LED3 = Start
LED4 = Stop
LED5 = Timer
LED6 = Pedestrian
LED7 =Encoder
LED8 =Power supply
LED9 =Programming
CN1 = Transformer motor connector
CN2 = Encoder connector
CN3 = Inputs/outputs 24V connector
LE
D4
LE
D
5
D
6
Rv3Rv3
LE
F2F2
D
CN6CN6
L
E
D
7
CN1CN1
1 2 3 4
Rv1Rv1
RL1RL1
Rv2Rv2
RL2RL2
DIPDIP
U1U1
F1F1
CN5CN5
L
D
9
CN4 = Flashing lamps 24V connector
CN5 = Batterycharger connector (see last page)
CN6 = Radio receiver connector
Rv1 = Motor speed regulation
Rv2 = Slow down speed regulation
Rv3 = Anti-crushing sensibility regulation
P1 = Working time memorizing push button
DIP = Dip switch for functions setting
F1 = Power supply and motor (10A) fuse
F2 = Accessories fuse (2A)
RL1 - RL2 = Relè motor direction
U1 = Microcontroller
8E
67410617
Rev. 01 - 10/2008
Sistemi Elettronici
di Apertura Porte e Cancelli
International registered trademark n. 804888
CONNECTIONS
®
SEA S.r.l.
DIREZIONE E STABILIMENTO:
Zona industriale 64020 S.ATTO Teramo - (ITALY)
Tel. 0861 588341 r.a. Fax 0861 588344
CN3
http://www.seateam.com
e-mail:seacom@seateam.com (Uff. Comm.le)
seatec@seateam.com (Uff. Tecnico)
English
CN4
1 2 3 4 5 6 7 8 9 10
c
4
2 Vd
N
O
O
C MM
V
0
DIP
ONON
11 22 33 44 55 66 77 88
l
T
R
ce
dge
E
y
et
f
a
S
A
o
o l
S T
h t
P
r
P
O
T
S
ON= Working function
Working Logics
Safety Reverser
Photocell in Opening
Closing with Photocell
Not working
Pre-flashing
Programming
e
m
i
T
1 2 3 4 5 6
d
d
e
use
t us
t
o
No
N
m
a
mpl
r
St t
MO
M
an
i
O N
r
t
C
e a
P des
g a
si
L
hn
Fa
m x
5
1
V W
4
2
max
L
g a p
W
n
i
3
n
V
4
ar
2
W
CN2 (ENCODER)
1 2 3
en
re
G
V
0
w
i
h
Bro
W
)
l
a
V
n
5
+
Sig
(
e
at
D
n
e
t
CN1
1 2 3 4
67410617
Rev. 01 - 10/2008
M
Tra
f
s
n
22Va
r
me
or
c
®
SEA S.r.l.
DIREZIONE E STABILIMENTO:
Sistemi Elettronici
di Apertura Porte e Cancelli
International registered trademark n. 804888
Zona industriale 64020 S.ATTO Teramo - (ITALY)
Tel. 0861 588341 r.a. Fax 0861 588344
SETTING OF WORKING LOGICS
ONON
http://www.seateam.com
e-mail:seacom@seateam.com (Uff. Comm.le)
seatec@seateam.com (Uff. Tecnico)
English
1 2 1 2 1 2 1 2
TYPE 1 LOGIC WITH STEP BY STEP COMMANDS
The repeated start realizes the following sequence: open-stop-close-stop-open-stop-close
TYPE 2 LOGIC WITH STEP BY STEP COMMANDS
The repeated start realizes the following sequence: open-stop-close- open-stop-close-......
AUTOMATIC LOGIC (automatic closing)
The start only opens when the automation is closed, in opening it stops, in pause it
immediately closes, in closing it opens again. It makes the automatic closing when the pause
time has ended or with another start it immediately closes.
CONDOMINIUM LOGIC (automatic closing)
The start only opens when the automation is closed, in opening it does not work, in pause it
does not work (it continues the counting of the set time), in closing it opens again.
OTHER FUNCTIONS
ONON
INTERVENTION OF THE SAFETY REVERSER IN CLOSING
OFF: It opens again and if the automatic closing is programmed after the pause time it closes.
If the closing has not been completed after two attempts, the sliding door stays opened and
waits for commands.
3
ON: It opens again and waits for commands.
ONON
PHOTOCELL IN OPENING
OFF: Photocell only in closing, in case the signal is interrupted they reverse the movement.
ON: Working photocell in opening and in closing, in case the signal is interrupted in opening
the photocells stop the movement and they open again when the signal is restored, while in
4
closing the movement is reversed only when the photocells are not obstructed.
ONON
ONON
67410617
CLOSING FUNCTION AFTER THE INTERVENTION OF THE PHOTOCELL
ON: If a pause time is programmed it is reduced to 3 seconds when the photocells are
interrupted in opening or in pause.
5
NOT WORKING
6
Rev. 01 - 10/2008
Loading...