SEA B 100 PLUS 1000N,B 100 PLUS 600N Installation Manual

English

Operators for garage doors

Imported by SEA S.p.A.

Zona industriale 64020 S.ATTO Teramo - (ITALY)

Tel. [phone] r.a. Fax [phone]

www.bleuteam.it

[e-mail]

REV 00 - 12/2014

INSTALLATION MANUAL

B 100 PLUS

600N

B 100 PLUS

1000N

English

INDEX

1. FUNCTION DESCRIPTION.....................................................................................3

2. OPENER PACKAGE CONTENTS..........................................................................5

3. IMPORTANT INSTALLATION INSTRUCTION ..............................................................6

4. INSTALLATION STEPS.................................................................................................7

4-1. MEASURE DOOR’S HIGHEST TRAVEL POINT......................................................7

4-2. INSTALL H EADER B RACKET............................ ....................................................7

4-3. INSTALL D OOR B RACKET T O D OOR.................................................... ... ........8

4-4. ATTACH RAIL TO OPENER HEAD........................................... ................................8

4-5. ATTACH RAIL TO HEADER BRACKET....................................................................9

4-6. MOUNT O PENER T O C EILING......................... ..................................................9

4-7. CONNECT A RM T O D OOR A ND T ROLLEY...................................................... 10

4-8. CHECK EMERGENCY RELEASE..........................................................................10

4-9. TENSION ADJUST ................................................................................................11

4-10. RAIL INSTALLATION.................. ..........................................................................11

5. CONTROL UNIT.......................................................................................................12

5-1. SAFETY AND CONTROL DEVICES CONNEXION......................13

5-2. CONTROL UNIT PROGRAMMING...............................................................13

5-3.TRANSMITTERS MEMORIZATION ................................................................13

5-4. RUN LEARNING.....................................................................14

5-5. THE ADJUSTMENT OF REVERSE FORCE .......................................................1. 4

5-6. USE PHOTOELECTRIC SWITCHES ..........................................................15

5-7. USE A UTOMATICALLY- CLOSING FUNCTION................................................. 15

6. TROUBLE SHOOTING ........................................................................................16

7. GENERAL NOTICE FOR THE INSTALLER AND THE USER .......................................17

REV 00 - 12/20142

In the event of a power cut all data remains permanently saved in the
program memory.
(End points, registered transmitters and the last position of the door.)

English

TECHNICAL DATA

TX Frequency:

230V/50Hz

140 170

120

4

600 1000

120

4

Standard

IP20

-20°C to +60°C

433.92 MHz

1. Functional description

The B 100 Plus 600N and B 100 Plus 1000N operators may be used for sectional doors.

Supply voltage:

Power(W):

Door (travel) speed(mm/s):

Maximum duty cycle(min):

Pulling force(N):

Internal release mechanism:

Protection category:

Permissible ambient temperature:

Data conservation:

Soft start

This function is integrated as a standard feature and guarantees a slow starting movement of the door.

Soft stop

With the aid of this function, the opener can slow down before reaching the final position.

Logic: OPEN - STOP - CLOSE - STOP - OPEN.

Additional connecting options for external accessories

In addition you can connect up external push buttons such as internal buttons, key switches and a wicket door contact.

Profile slide carriage

“Closed”

end position

“Open”

end position

Recognition of obstructions

The door opener has an automatic obstruction-recognition system (through internal monitoring of power).

If the door encounters an obstruction when closing or opening, the door opener stops the door automatically and moves it

approximately 10 cm in the opposite direction.

After removing the obstruction you can operate the garage door opener normally again.

REV 00 - 12/2014 3

B 100 PLUS

600N

B 100 PLUS

1000N

Internal release mechanism:

The models have an internal release mechanism with which you can open the garage door by hand in emergencies or in the event of

a power cut.

The internal release mechanism is attached to the profile slide with a rope and a knob. By pulling the rope you uncouple the garage

door from the opener and then you can open the door by hand.

It is suggested to:

• Close or open the door fully after each release.

• The emergency release is not intended for “everyday use”, since it is an emergency device..

Internal

release

mechanism

English

Rail and operators’ size

REV 00 - 12/20144

2. Opener package contents

The following items are included with the Garage Door Opener. The opener and rail are packaged with their respective
carton.

English

(A) OPENER
(B) ACCESSOIRES

a. Wall B racket (1x)
b. D. oor B raket & Plate (1x)
c. U Bracket (3x )

e. Clevis (1x)
f. Clevis (1x)
g. Cotter pin (3x)
h. Hex nut (1x)
i. Hex bolts (1x)

k. H ex H ead D riving S crew (4x)
(C) Straight Door Arm
(D) Curved Door Arm

(F) Rail

REV 00 - 12/2014 5

3. Important installation instructions

WARNING

1. READ AND FOLLOW ALL INSTALLATION INSTRUCTIONS

2. Check with the door manufacturer to determine if additional reinforcement is required to support the door prior to

installation of the garage door opener.

3. Install garage door opener only on a properly balanced garage door .An improperly balanced door could cause

seriously injury. Have a qualified service person make repairs to garage door cables, spring assemblies, and other

hardware before installing the opener.

4. Remove all ropes and disable all locks connected to the garage door before installing opener.

6.

After installing the opener, test Safety Reversal System. Door MUST reverse when touching an obstacle, within the

time and ways described in the regulations.

English

5. Do not connect the opener source of power until you have performed all the steps of these instructions.

7. Once a year: keep well lubricated rollers of the door, the hooks and the bearings following the instructions or
contacting a maintenance company.

REV 00 - 12/20146