Page 1
Installation and
User's Manual for
Outdoor Model Residential Ice Machine
Models SCCG50M-1SS and SCCP50M-1SS
Page 2
SCCG50 & SCCP50 - Outdoor Model
Installation and User's Manual
Introduction:
This ice machine is the result of Scotsman’s
decades of experience as an industry leader in the
design and manufacture of both commercial and
residential ice machines.
This manual includes the information needed to
install, start up and maintain the ice machine. Note
any Caution or Warning indicators, as they provide
notice of potential hazards. Keep this manual for
future reference.
Table of Contents
Specifications .......................................... Page 2
Air flow ............................................. Page 3
Cabinet Drawing ........................................ Page 4
Water Quality .......................................... Page 5
Door swing change ....................................... Page 6
Installation: Water & Drain ................................... Page 7
Gravity Drain .......................................... Page 8
Electrical ............................................ Page 9
Use ............................................... Page 10
Maintenance .......................................... Page 11
How to clean the condenser and winterize. ........................... Page 12
How to remove scale from the ice making system. ....................... Page 13
What to do before calling for service .............................. Page 14
Outdoor Use Notice:
Keep from freezing. Severe damage will occur to the unit if left in or operated in temperatures beyond
the limits listed in this manual. That damage is NOT covered by warranty.
Keep dry
Provide Shade
ultraviolet radiation from the sun can potentially damage the unit's plastic components.
Water Supply
should be rated for potable water and include UV protection. Copper tubing is recommended.
Back Flow Prevention
. Do not locate in low lying areas where puddles will accumulate.
: Heat gain from the sun will reduce the unit's ability to make and store ice, and
: Avoid a long run of hose or tubing exposed to the sun. Plastic water supply tubing
: The unit includes back flow prevention, no additional check valve is required.
Drainage
Operation
below 65 degrees F.
: Do Not drain into swimming pool or onto grounds.
: It is normal for the ice level in the storage bin to be low when unit is used in temperatures
June 2008
Page 1
Page 3
Specifications
SCCG50 & SCCP50 - Outdoor Model
Installation and User's Manual
This ice machine is designed to be used indoors, in
a controlled environment or outdoors within certain
limits. It can be used in a wide variety of
environmental conditions, but there are limits. Use
outside of the listed limitations is misuse and will
void the warranty.
Air temperature limits:
The ice machine will operate adequately within the
limits, but functions best in temperatures between
70 and 80 degrees F.
Minimum – 50 degrees F. (10oC)
•
Maximum – 100 degrees F. (38oC)
•
Water temperature limits:
Minimum – 40 degrees F. (4.5oC)
•
Maximum – 100 degrees F. (38oC)
•
Water pressure limits:
Options:
Drain Conversion:
A gravity drain model can be converted to a drain
pump model by installing a drain pump kit. The
drain pump kit consists of a drain pump, wiring
harness and associated tubing. The part number is
A39462-021.
Warranty Information
Warranty information is supplied separately from
this manual. Refer to it for coverage. In general, the
warranty covers defects in materials or
workmanship and does not cover corrections of
installation errors or maintenance.
Minimum – 20 psi (1.4 bar)
•
•
Maximum – 80 psi (5.5 bar)
Because the ice machine is making a food product,
the water supply to the ice machine must be
potable, or fit for human consumption.
Electrical voltage limits:
•
Minimum - 104 volts
•
Maximum – 126 volts
Models
There are two models, both air cooled:
•
SCCP50M-1SS – Pump model, stainless cabinet and door
•
SCCG50M-1SS – Gravity drain model, stainless cabinet and door
Dimensions
Width Depth, handle adds 1 5/8" Height
14 7/8" 22 3/4" 33 3/8" to 34 3/8"
July 2008
Page 2
Page 4
SCCG50 & SCCP50 - Outdoor Model
Installation and User's Manual
Air flow
The machine takes in room temperature air at the
lower right front and forces warm air out the lower
left front. Restricting the airflow or operating the
machine in a hot or cold environment will adversely
affect the ability of the ice machine to make ice.
When the door is opened, the control panel, ice
making area and ice storage bin are visible. The
scoop is located in a holder along the right side
wall.
Scotsman Ice Systems are designed and
manufactured with the highest regard for safety
and performance. They meet or exceed the
standards of agencies like U.L.
Scotsman assumes no liability or responsibility of
any kind for products manufactured by Scotsman
that have been altered in any way, including the
use of any parts and/or other components not
specifically approved by Scotsman.
Scotsman reserves the right to make design
changes and/or improvements at any time.
Specifications and designs are subject to change
without notice.
Air IntakeWarm Air Out
Control Panel
Ice Making
Area
June 2008
Page 3
Page 5
Cabinet Drawing
14 7/8"
AIR IN
AIR OUT
.75
SHEET METAL DOOR FRONT
.63 MIN. CABINET DOOR
29 1/4"
1"
LEG ADJUSTMENT
(4) PLACES
33 3/8" MIN.
34 3/8" MAX.
22"
2 3/4"
4"
3 3/4"
1 1/2"
2 1/2"
3 1/4"
7 3/8"
115 V
POWER CORD
DRAIN
FLEXIBLE TUBING
3/8 I.D. PUMP MODEL (INCLUDED)
5/8 I.D. GRAVITY MODEL (NOT INCLUDED)
POTABLE WATER INLET
1/4" COMPRESSION FITTING
3 7/8"
20 3/8"
FLOOR DRAIN
ACCESS HOLE
SCCG50 & SCCP50 - Outdoor Model
Installation and User's Manual
Installation Notes
Built In Situations: If a finished floor is to be installed in the area after the ice machine has been built in,
shims the expected thickness of the floor should be installed under the unit to keep the machine level
with the planned floor level.
Installations on a slab: Use a pump model and pump the water to the point of drainage. Pump models
will pump 1 story (10 feet) high.
Installations over a crawl space or basement: Either gravity drain or pump model units may be used, if
there is not enough room behind the machine for a drain/waste receptacle, the drain will have to be
below the floor.
Note: When installed in a corner, the door swing may be limited due to handle contact with the wall or
cabinet face.
June 2008
Page 4
Page 6
SCCG50 & SCCP50 - Outdoor Model
Installation and User's Manual
Water Quality
All water, including potable water supplied by
municipalities, contains some impurities or
minerals. Water absorbs impurities from the air as
rain and/or as it flows through the ground. Some of
the impurities are solid particles, these are known
as suspended solids, and a fine particle filter will
remove them. Other impurities are chemically
bonded to the water molecules, and cannot be
filtered out, these are called dissolved solids.
Ice made by this machine will have a lower mineral
content than the water it was made from. This is
due to the method of making ice. Purer water will
freeze first in the ice making molds. The reason for
this is that anything dissolved in water lowers the
water’s freezing temperature. This concentrates
most of the impurities in the ice machine water
reservoir where they may form hard deposits
known as scale. The machine dilutes the
concentration of minerals by over-filling the
reservoir during the harvest cycle (with the excess
water flowing down the drain). Water use varies
with air and water temperatures. Between 2 and 4
pints of water flow into the unit each cycle.
Between 1 and 3.5 pints of that rinses the reservoir
and goes down the drain.
Some impurities will inevitably remain, and will stick
to the parts in the machine, and will cause
malformed ice cubes. Eventually, built up mineral
scale can shorten machine life.
Filters and Treatment
In general, it is always a good idea to filter the
water. A water filter, if it is of the proper type, can
remove taste and odors as well as particles. Some
methods of water treatment for dissolved solids
include reverse osmosis, and polyphosphate
feeders.
RO Water
This machine can be supplied with Reverse
Osmosis water, but the water conductivity must be
no less than 10 microSiemens/cm. A reverse
osmosis system should include post treatment to
satisfy the R.O. water’s potential aggressiveness.
Deionized water is not recommended.
Because water softeners exchange one mineral for
another, softened water may not improve water
conditions when used with ice machines. Where
water is very hard, softened water could result in
white, mushy cubes that stick together.
If in doubt about the water, contact a local point of
use water specialist for recommendations on water
treatment.
Installation Overview
The ice machine must:
To keep the machine operating properly, these
impurities or minerals will have to be regularly
dissolved by an acid cleaning, using Scotsman Ice
Machine Scale Remover. Directions for this may be
found in the section under cleaning.
•
be connected to cold, potable water
•
be connected to a drain
•
be connected to the proper power supply
•
be able circulate air through the vents at the
front.
Note: Do not build in so that the door is recessed.
June 2008
Page 5
Page 7
Door swing change
SCCG50 & SCCP50 - Outdoor Model
Installation and User's Manual
Note: Prior models had separate hinge brackets
and different directions to change swing.
Moving the hinges allows the door to open from
either the left or right side. Change swing before
attaching door panel.
To change:
1. Remove innermost screw holding each hinge
to cabinet, loosen the other.
2. Slide door to the side and remove from cabinet.
3. Remove plug and hinge pocket covers from
door.
Note: If door panel is attached, it must be removed
to access hinge screws and to reverse handle
position.
8. Remove the original lower hinge and move it to
the door's opposite side, upper location.
Secure using the original screws.
9. Install pocket covers and hole plugs onto door.
10. Attach the door to the cabinet using the original
screws.
Installation Notes
Built In Situations: If a finished floor is to be
installed in the area after the ice machine has been
built in, shims the expected thickness of the floor
should be installed under the unit to keep the
machine level with the planned floor level.
Installations on a slab: Use a pump model and
pump the water to the point of drainage. Pump
models will pump 1 story (10 feet) high.
Hole
Plug
Hole
Cover
Note: There are either plugs or screws in the holes
where the hinges will mount. They must be moved.
4. Remove hole plugs or screws from unit's new
hinge locations, set aside.
5. Move screws loosened in step 1 to opposite
location.
6. Install screws or plugs removed in step 4 to the
unit's original hinge location to fill the holes.
7. Remove the upper hinge from the door and
move it to the door's opposite side, bottom
location. Secure using the original screws.
Installations over a crawl space or basement:
Either gravity drain or pump model units may be
used, if there is not enough room behind the
machine for a drain/waste receptacle, the drain will
have to be below the floor.
Note: When installed in a corner, the door swing
may be limited due to handle contact with the wall
or cabinet face.
January 2012
Page 6
Page 8
SCCG50 & SCCP50 - Outdoor Model
Installation and User's Manual
Installation: Water & Drain
The recommended water supply tubing is ¼ inch
OD copper. Stainless steel flex or reinforced PCV
tube may also be used. Install an easily accessible
shut-off valve between the supply and the unit. This
shut-off valve should not be installed behind the
unit.
Note: Do not use self-piercing type valves.
1. Remove the front service panel.
Screw
Securing
Front Service
Panel
Drains
There are two types of ice machine models, one
that drains by gravity and one that has an internal
drain pump.
Drain Pump Model drain installation
1. Locate the coil of 3/8” ID plastic drain tubing
secured to the back of the unit.
2. Route the plastic drain tube from the back of the
unit to the drain connection point.
IMPORTANT NOTE: Often an air gap is required by
local codes between the ice maker drain tube and
the drain receptacle.
Keep unit from
Freezing
2. Route the tubing through the right hole in the
back to the inlet water solenoid valve inlet.
3. Install a compression fitting on the tubing and
connect to the inlet of the solenoid.
Drain Tube,
Route to
building drain
Water Inlet
Tube (field
supplied)
Back View, Drain Pump Model
June 2008
Page 7
Page 9
Gravity Drain
SCCG50 & SCCP50 - Outdoor Model
Installation and User's Manual
Caution: Restrictions in the drain system to the
machine will cause water to back up into the ice
storage bin and melt the ice. Gravity drain tubing
must be vented, have no kinks and slope to the
building drain. Air gaps are typically required by
local code.
1. Place the ice machine in front of the installation
opening. Adjust leveling legs to the approximate
height.
2. Remove the front service access panel and the
upper back panel.
Note: If you are connecting a gravity drain model
and the drain opening has been located in the floor
under the base pan according to the pre install
specifications, follow steps 3 through 5 to drain the
unit through the base. If not, proceed to step 6b.
3. Remove the clamp and barbed elbow and take
off the plastic cover in the base pan below the drain
hose.
4. Connect a straight 5/8” barbed connector to the
drain hose, securing with the clamp removed in
step 4.
5. Cut an 8” piece of 5/8” ID X 7/8” OD tygon (clear
plastic) tubing. Slide one end of the tube onto the
outlet of the barbed connector and secure with a
clamp. Leave the other end of the tube lying on the
floor of the base pan until the unit is positioned
over the floor drain.
6. Route the drain tube. Either a) Insert the drain
tube through the base pan into the floor drain or b)
Route the drain tube through the left hole in the
lower back panel and connect to barbed elbow and
secure with a clamp.
7. Reinstall the upper back panel.
8. Reinstall the service access panel. Level the
unit.
Drain Hose
Drain Hose,
Route to
building drain
Barbed Elbow
Water Inlet
Tube (field
supplied)
Back View, Gravity Drain Model
June 2008
Page 8
Page 10
SCCG50 & SCCP50 - Outdoor Model
Installation and User's Manual
Electrical
The ice machine is supplied with a power cord. Do
not remove the grounding pin from the cord’s plug.
Do not use extension cords. Follow all codes.
Connect the machine to its own 115 volt, 15 amp
circuit.
1. If the electrical outlet for the ice maker is
behind the unit, plug in the unit.
2. Position the unit in the installation opening.
3. Turn on the water supply. Make sure that the
ice maker is plugged in and the power is on.
4. Slide unit into installation opening, paying
careful attention to water supply and drain
connections. Do not kink!
5. Pour a couple of quarts of water into the ice
storage bin; on drain pump equipped machines
the drain pump should start and water should
pump out. Check for leaks.
6. Replace the service access panel.
Installation check list:
1. Has the unit been connected to the proper
water supply?
2. Has the water supply be checked for leaks?
3. Has the unit been connected to a drain?
4. Has the drain been tested for flow and leaks?
5. Has the unit been connected to the proper
electrical supply?
6. Has the unit been leveled?
7. Have all packing materials been removed from
the machine?
Initial Start Up
1. Turn on the water supply.
2. Switch on the electrical power.
7. Level the unit as needed.
3. Push and release the On/Off switch to start the
machine. The Ice Making light next to the
On/Off switch will glow Green.
Water will begin to flow into the unit. When the
4.
reservoir is full, water will start to drain from the
machine. After a few minutes the compressor,
water pump and fan motor will begin to operate
and the first ice making cycle will have begun.
No adjustments are needed.
After about a half hour, ice will fall into the ice
storage bin. The machine makes 24 cubes per
batch. It is normal for the first batches of ice to
melt, that continues until the bin has cooled. It will
take 8 to 10 hours of continuous run time to fill the
ice bin. When the bin is full of ice, the ice machine
will shut off. It will automatically restart when the
ice level falls, either from use or normal meltage.
July 2008
Page 9
Page 11
Use
No special instructions are needed for use. Just
take as much ice as you need, the machine will
replace it. A scoop is provided, and it can be stored
in the machine using the loop of tubing on the right
side as a holder.
The machine can be shut off anytime by just
pushing and releasing the On/Off button. The
machine will shut off at the end of the next cycle.
To shut off immediately, push and hold the On/Off
button in until the machine stops.
SCCG50 & SCCP50 - Outdoor Model
Installation and User's Manual
What shouldn’t be done?
Never keep anything in the ice storage bin that is
not ice. Objects like wine or beer bottles are not
only unsanitary, but the labels can slip off and plug
up the drain.
Never allow the machine to operate without regular
cleaning. The machine will last longer if it is kept
clean. Regular cleaning should happen at least
once per year, and preferably twice. Some water
conditions will dictate even more frequent cleaning
of the ice making section, and some carpets or
pets will dictate more frequent cleaning of the
condenser.
Note: The Time to Clean light will switch ON after 6
months of use. It will remain ON until the ice
making system is cleaned using the process on
page 12.
Noise:
Normal cubes are tapered cylinders. If the cubes
are ragged and mis-shaped, mineral scale must be
removed from the ice making system
The ice machine is designed for quite operation,
but will make some noise during the ice making
cycle. During a freezing cycle, it is normal to hear
the fan moving air and the water pump circulating
water. Ice hitting the bin or ice in the bin can be
heard during harvest.
If ice making noise is objectionable, an appliance
grade timer can be added to the power supply. Set
the timer to turn the machine off at the time(s) of
day when the noise is most objectionable.
June 2008
Page 10
Page 12
SCCG50 & SCCP50 - Outdoor Model
Installation and User's Manual
Maintenance
There are 5 things to keep clean:
1. The outside cabinet & door.
2. The ice storage bin.
3. The condenser.
4. The ice making system.
5. The ice scoop.
How to clean the cabinet.
Wipe off any spills on the surface of the door and
handle as they occur. If anything spilled on the
door or gasket dries onto the surface, wash with
soap and warm water to remove.
How to clean the ice storage bin.
The ice storage bin should be sanitized
occasionally. It is usually convenient to sanitize the
bin after the ice making system has been cleaned,
and the storage bin is empty.
A sanitizing solution can be made of 1 ounce of
household bleach and two gallons of hot (95
o
115
F.) water. Use a clean cloth and wipe the
o
F. –
interior of the ice storage bin with the sanitizing
solution, pour some of the solution down the drain.
Allow to air dry.
June 2008
Page 11
Page 13
How to clean the condenser and winterize.
SCCG50 & SCCP50 - Outdoor Model
Installation and User's Manual
Condenser cleaning
The condenser is like the radiator on a car, it has
fins and tubes that can become clogged with dirt
and lint.
Note: Outdoor operation can lead to rapid build up
of debris, such as leaves and other vegetation. The
condenser will need to be frequently checked for
debris. Clean it whenever the fins are obstructed.
Winterizing
1. Clean the ice making system.
2. Open the door and push and release the On/Off
switch to turn the machine off.
3. Turn off the water supply.
4. Drain the water reservoir by removing the rubber
cap under the reservoir - it's near the back wall of
the ice storage bin.
Rubber Cap
Condenser
Surface
To clean:
1. Remove the kickplate and front service panel.
2. Locate the condenser surface.
3. Vacuum the surface, removing all dust, dirt and
lint.
Caution: Do not dent the fins.
4. Return the kickplate and front service panel to
their original positions. Fasten them to the cabinet
using the original screws.
5. Disconnect the incoming water line at the inlet
water valve.
6. Open the door, push and release the on/off
switch to turn the machine on.
7. Blow air through the inlet water valve; a tire
pump could do the job.
8. Drain pump models should have about 1/2
gallon of RV antifreeze (propylene glycol) poured
into the ice storage bin drain.
Note: Automotive antifreeze must NOT be used.
9. Switch off and unplug the machine.
June 2008
Page 12
Page 14
SCCG50 & SCCP50 - Outdoor Model
Installation and User's Manual
How to remove scale from the ice making system.
1. Scoop out all of the ice, either discard it or save
it in an ice chest or cooler.
2. Press and HOLD the On/Off button in for 3
seconds until the Green light goes out.
3. Press and HOLD the both the Clean-Reset and
On/Off buttons for 5 seconds. The Time to Clean
light will blink on and off.
4. Pour 4 ounces of Scotsman Ice Machine Scale
Remover (available from a local Scotsman
Distributor or Dealer) into the ice machine
reservoir.
10. Clean the bin liner of mineral scale by mixing
some ice machine scale remover and hot water,
and using that solution to scrub the scale off of the
liner.
11. Rinse the liner with hot water.
12. Sanitize the bin interior.
13. Replace the ice removed in step 1.
14. Push and release the On/Off button to restart
ice making.
The ice scoop should be washed regularly, wash it
just like any other food container.
5. Operate the machine for about ½ hour.
6. Push and release the On/Off switch. The
machine will begin to flush out the cleaning
solution.
7. Operate the machine for another ½ hour.
8. Push and release the On/Off switch. The
machine will stop the cleaning process.
9. Pour a gallon of hot (95
o
F. – 115oF.) water into
the bin to flush out the drain.
Pour Scale
Remover Here
June 2008
Page 13
Page 15
What to do before calling for service
Ice cubes are incompletely formed
Clean the ice making system
•
Low capacity
Check for restricted drain or standing water
•
in the bin
Clean the air cooled condenser fins
•
No ice
Check on-off switch
•
Check electrical breaker
•
If the Check Water light is flashing Red,
•
check water supply. The control system
checks for water every 20 minutes. When the
water supply is restored, the machine will
automatically restart ice making.
SCCG50 & SCCP50 - Outdoor Model
Installation and User's Manual
Time to Clean light is on
Clean the ice making system.
•
June 2008
Page 14
Page 16
SCOTSMAN ICE SYSTEMS
775 Corporate Woods Parkway
Vernon Hills, IL 60061
800-726-8762
www.scotsman-ice.com
17-3191-03
Loading...