Sargent P2 PASSPORT 1000,P2 1000 Installation Instructions Manual
P2
PASSPORT 1000
Cylindrical Lock
Installation Instructions
A8013F
03/14
Copyright 2013, Sargent Manufacturing Company, an ASSA ABLOY Group company.
All rights reserved. Reproduction in whole or in part without the express written
permission of Sargent Manufacturing Company is prohibited.
Table of Contents
1
Warning ...................................................................................2
General Description .................................................................3
2
3
Hardware Specifications .........................................................3
4
Electronic Specifications .........................................................3
Parts Breakdown .....................................................................4
5
Installation Instructions ..........................................................6
6
7
Operational Check ................................................................16
1
Warning
Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
FCC
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the
FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Industry Canada:
This Class B digital apparatus meets all requirements of the Canadian Interference Causing Equipment Regulations. Operation is subject
to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Cet appareillage numérique de la classe B répond à toutes les exigences de l’interférence canadienne causant des règlements
d’équipement. L’opération est sujette aux deux conditions suivantes: (1) ce dispositif peut ne pas causer l’interférence nocive, et (2) ce
dispositif doit accepter n’importe quelle interférence reçue, y compris l’interférence qui peut causer l’opération peu désirée.
“This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator and your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.”
Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type and its gain should
be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for successful communication.
Conformément à la réglementation d’Industrie Canada, le présent émetteur radio peut fonctionner avec une antenne d’un type et d’un
gain maximal (ou inférieur) approuvé pour l’émetteur par Industrie Canada. Dans le but de réduire les risques de brouillage radioélectrique
à l’intention des autres utilisateurs, il faut choisir le type d’antenne et son gain de sorte que la puissance isotrope rayonnée équivalente
(p.i.r.e.) ne dépasse pas l’intensité nécessaire à l’établissement d’une communication satisfaisante.
Any retrofit or other field modification to a fire rated opening can potentially impact the fire rating of the opening, and SARGENT Manufacturing makes no representations or warranties concerning what such impact may be in any specific situation. When retrofitting any portion
of an existing fire rated opening, or specifying and installing a new fire-rated opening, please consult with a code specialist or local code
!
official (Authority Having Jurisdiction) to ensure compliance with all applicable codes and ratings.
To avoid possible damage from electrostatic discharge (ESD), some basic precautions should be used when handling
electronic components:
Copyright © 2013, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved.
Reproductions in whole or in part without express written permission of Sargent Manufacturing Company is prohibited.
• Minimize build-up of static by touching and/or maintaining contact with unpainted metal surfaces such as
door hinges, latches, and mounting plates especially when mounting electronic components such as readers
and controllers onto the door.
• Leave components (reader and controller) protected in their respective anti-static bags until ready
for installation
03/31/14
1-800-810-WIRE • www.sargentlock.com • A8078A
• Do not touch pins, leads or solder connections on the circuit boards
Passport 1000 P2 WiFi Cylindrical Lock
2
General Description
The SARGENT Passport 1000 P2 Cylindrical Lock features HID® multiCLASS SE™ technology, offering
simultaneous support for multiple credential formats as well as an easy migration path to higher security
credentials and NFC mobile access.
Designed specifically for the campus market, the SARGENT Passport 1000 P2 WiFi Cylindrical Lock provides
access control with magnetic swipe and optional contactless Reader and/or Keypad, as well as detailed audit
capabilities.
• Using WiFi technology and coupled with third party software, the P2 Cylindrical lock offers a complete,
integrated access control system.
• The Passport 1000 P2 operates on six (6) “AA” alkaline batteries and may be used for both indoor and
outdoor applications.
Note: A weather-protective gasket is recommended for outdoor applications.
HID, iCLASS, iCLASS SE, and multiCLASS SE are registered trademarks or trademarks of HID Global in the U.S. and/or
other countries.
3
Hardware Specifications
• Complete locksets with controller
• Easily retrofits existing Passport 1000
(cylindrical lock) door preps
• ADA Compliant
• Grade 1; UL Listed
• Latch 1/2” standard 3/4” throw fire-rated
double doors (optional) (41- prefix)
• Deadlocking latch
• Outside lever is unlocked through access
control credentials only
• Inside lever retracts latch
• Outside lever controlled by any combination of
keypad, magnetic swipe, contactless reader or
mechanical cylinder
4
Electronic Specifications
• Input Power: DC 9V, 1.5A (6 AA alkaline batteries)
• Optional hard-power 12VDC to 24VDC
• HID® multiCLASS SE™ technology offers support
for the following credentials:
• High Frequency (13.56 MHz):
• HID iCLASS
• HID iCLASS SE® (SIO-enabled)
• HID iCLASS
• HID MIFARE® SE
• HID DESfire® EV1 SE
• MIFARE Classic
• DESfire EV1
• FeliCa
• Low Frequency (125 kHz):
• HID Prox
• Magnetic Stripe
• WiFi (IEEE 802.11 b/g/n)
• Multiple time zone and holiday access scheduling
• First-in unlock or automatic unlock configuration,
based on specified time schedule
• Support for most advanced wireless encryption
®
®
®
Seos
™
and authentication standards such as WEP, WPA,
WPA2 and 802.1x*
• 2,400 users per lock; 10,000 event audit trail
• Privacy button
*For specific security information, please contact
your local ASSA ABLOY Door Security Solutions
sales consultant or call 800-810-WIRE.
Copyright © 2013, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved.
Reproductions in whole or in part without express written permission of Sargent Manufacturing Company is prohibited.
1-800-810-WIRE • www.sargentlock.com • A8013F 3
03/31/14
5
Parts Breakdown
P2 WiFi Lock with Magnetic Card Swipe With or Without Keypad
Passport 1000 P2 WiFi Cylindrical Lock
4
3
1
ITEM No. PART No. DESCRIPTION
1 52-3583-[finish] Outside Escutcheon Assemby, mag stripe
52-3582-[finish] Outside Escutcheon Assemby, mag stripe and Keypad (shown)
52-4244-[finish] Outside Escutcheon Assemby, Mag Swipe, Keypad, and HID 125 kHz Prox
52-4759-[finish] Outside Escutcheon Assemby, iCLASS, keypad, mag stripe, Prox, smart card (MIFARE, DESFIRE)
52-4777-[finish] Outside Escutcheon Assemby, iCLASS, mag stripe, Prox, smart card (MIFARE, DESFIRE)
52-4787-[finish] Outside Escutcheon Assemby, FeliCa, keypad, mag stripe, Prox
52-4788-[finish] Outside Escutcheon Assemby, FeliCa, mag stripe, Prox
52-4779 Mounting Plate Assembly
2
52-5409 WiFi Controller Assembly
3
52-4796 WiFi Radio Module (not shown)
4 52-4776-[finish] Inside Escutcheon Assembly with Privacy Button
5 52-5373 Door Position Switch Kit
2
5
Copyright © 2012, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved.
Reproductions in whole or in part without express written permission of Sargent Manufacturing Company is prohibited.
03/31/14
4 1-800-810-WIRE • www.sargentlock.com • A8013F
Passport 1000 P2 WiFi Cylindrical Lock
Parts Breakdown (Continued)
10 Line Series Cylindrical Lock
7a
11
12
4
5
7
*
6
5
4
3
2
1
ITEM PART No. DESCRIPTION REQ’D
1 --- Outside Lever (Reference Catalog for Available Styles) 1
2 10-0043 Lever Retainer Key (In Screw Pack 10-2052) 1
3 --- Cylinder Assembly (Reference Catalog for Available Cylinders) 1
4 --- Rose (Reference Catalog for Avalable Styles) 2
5 10-0792 Spacer Bushing 2
6 10-3049 Outside Rose Spring Assembly 1
7 10-3449 Lockbody Assembly 10G77 - Standard Cylinder 1
10-3450 Lockbody - LFIC 1
10-3451 Lockbody - SFIC 1
7a 52-4844 Lockbody Harness 1
8 10-0847 Adapter Plate/Spacer (*Only Included With 1-3/8” Thick Doors) 1
9 10-3192 Latch Assembly 1
10 10-2052 Screw Pack 2
11 10-3048 Inside Rose Spring Assembly 1
12 --- Inside Lever (Reference Catalog for Available Styles) 1
*Adapter Plate/Spacer (10-0847)
is only shipped with orders that
specify 1-3/8” doors.
8
10
9
Tools Required:
• #2 Phillips screwdriver
• Flat head
• T20 Torx® driver
• Security allen wrench
(provided)
1-800-810-WIRE • www.sargentlock.com • A8013F 5
Copyright © 2013, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved.
Reproductions in whole or in part without express written permission of Sargent Manufacturing Company is prohibited.
03/31/14
Loading...