Sanyo VCC-HD5400P, VCC-HD5400 User Manual

SUMMARY/SETUP MANUAL

Megapixel Camera

VCC-HD5400
VCC-HD5400P

THIS INSTALLATION SHOULD BE MADE
BY A QUALIFIED SERVICE PERSON AND
SHOULD CONFORM TO ALL LOCAL
CODES.

Before installing and using the camera, please read
this manual carefully.
Be sure to keep it handy for later reference.
In addition, be sure to read carefully the electronic
manual (INSTRUCTION MANUAL) contained in the
supplied CD-ROM to ensure correct operation of
the camera.

Important



Be careful when opening holes for installing

•

the unit. Work with the power and video cables
pulled out for easy installation.
Make sure to properly perform waterproofi ng for

•

the ceiling where you are installing the unit.
Make sure that the surface in the installation

•

location has no unevenness and is strong
enough to bear the total weight of the unit.
Install this unit in an environment where the

•

temperature range stays between –10°C and
+50°C/14°F and 122°F (no condensation
allowed).
As a precaution against static electricity

•

damage, touch a nearby metal object (door
knob, etc.) to dissipate static electricity in your
body before touching this unit.

EnglishFrançaisEspañolDeutschЁ᭛ㅔԧ日本語

Contents

Name and Function of Each Component ..................................................................... 2

Basic Connections ....................................................................................................... 5

Installation .................................................................................................................... 9

Control/Address Settings ........................................................................................... 11

Address Settings Table............................................................................................... 12

Network Settings ........................................................................................................ 13

Specifications ............................................................................................................. 14

Copyright Notice ........................................................................................................16

Accessories

■

① Pattern sheet ② Mounting plate ③ Hexagonal wrench ④ Fixer ⑤ CD-ROM

⑥ Clamping core: To prevent electromagnetic interference

VCC-HD5400

• VCC-HD5400P

•

×2

Check your operating environment.

■

To operate the camera via network operation, you must meet the following operating requirements.

• : IBM PC/AT compatible

PC

• : Windows XP Professional/Windows Vista

Operating system
CPU• : Core2Duo E6700 2.66 GHz or higher

• : Windows XP: 1GB or more

Memory

• : 10Base-T/100Base-TX (RJ-45 connector)

Network interface
Display card• : 1920×1200 pixels or higher

• : ATI RADEON HD2600 series or higher

Graphics chip

Web browser• : Internet Explorer Ver. 6.0 SP2 or higher,

You can automatically set up the IP address of the camera.

■

This software application is useful when two or more cameras are connected to the network.
Download “Auto IP Setup” software application from the supplied CD-ROM.

×5

Windows Vista: 2GB or more

nVIDIA GeForce 8600 series or higher
nVIDIA Quadro FX550 series or higher

or Internet Explorer Ver. 7.0

1

Name and Function of Each Component

For the cable type, see the “cable label” attached to the cable bundle.
For the detailed connection procedure, refer to the “Basic Connections” section. (

Page 5)

①④⑤

24 VAC

12 VDC

GND

~
~

-

+

③

②

⑥

① 24 VAC /12 VDC Power cable
② Alarm cables

Alarm input cable: Connect an external switch, infrared sensor, or other device to detect alarm

•

Alarm output cable: Connect a buzzer, lamp, or other alarm device.

•

③ Dip switch (

󱤨󱤩

ON

conditions such as the entry of an intruder.

Page 11 “Control/Address Settings”)

ON

654321

12345678

󱤨 Control switch: Use this switch to configure the baud rate and protocol settings.

󱤩 Address switch: Use this switch to configure the camera control address.
④ Network Socket (LAN: RJ-45, PoE)
⑤ EX-HDD terminal (USB type)

To record video on an external hard disk drive, you must install a 2.5" hard disk drive (SATA) in the

dedicated hard disk case (VA-HDC4000) which is sold separately and then connect the hard disk

drive case.

⑥ HDMI Connector

The terminal outputs super-fine HD (High Definition) video signal. Use the terminal to connect a

high-definition monitor with HDMI interface.

2

Name and Function of Each Component

⑦

⑧

⑬

⑫

⑪

-

󱤨󱤩

⑨

⑦ Control cable

By connecting a system controller (sold separately), the camera can be controlled remotely.

⑧ Wire gutter cover

If you wire on the ceiling surface, remove the wiring gutter cover.

⑨ Audio jacks

󱤨

Audio output terminal (black: 3.5-mm mini jack)

Use this jack to connect to the audio input jacks of a powered speaker system or a monitor.

󱤩 Audio input terminal (white: 3.5-mm mini jack)

Use this jack to connect an external microphone to listen to the sound while monitoring the live
video, or simultaneously record the video and sound.

This jack supports 3.5-mm monaural microphone plugs, or monaural line-level input plugs (the left
channel only for stereo plugs).

⑩ Monitor output terminal (BNC type)

Connect this terminal to a monitor, etc. A live video will be displayed on the monitor once the

camera is turned on.

⑪ Cable holder
⑫ Safety cable

Use this cable to hook the camera on the supplied mounting plate when installing the camera.

⑨

-

⑩

3

Name and Function of Each Component

⑬ Side Cover

󱤩󱤪 󱤫

󱤨

󱤨 Fall-prevention screw

󱤩 SD Card slot

󱤪 Power indicator

This indicator lights up when the camera is powered on.

When the camera is on, this indicator blinks to indicate the following camera statuses:

•

Deactivation of recording to SD memory card in progress

•

Firmware update in progress

•

An SD memory card error occurred (Fast blink)

󱤫 SD CARD button

Disable recording: The power indicator blinks when this button is pressed, and stays lit when

•

Enable recording: The power indicator blinks when this button is pressed, and stays lit when

•

the SD memory card is prepared to be removed.

the SD memory card is recognized.

Installing Recording Media

Before you insert an SD card, be sure to turn off the camera.

•

•

If you insert an SD card, format it via network operation on the SD/HDD screen.

Electronic manual)

(

SD memory card

■

How to insert the SD card

•

To record live video on a SD memory card, open the cover
as shown below and insert the card into the card slot until
you hear a click.

How to remove the SD card

•

Press the SD CARD button and, after confirming that the
indicator lamp has stopped blinking and now stays lit, take
out the SD card.

External HDD

■

Use the optional hard disk case (VA-HDC4000) to install the SANYO-specified 2.5" SATA hard
disk drive and connect the drive to the EX-HDD terminal.
For detailed information on the hard disk case including hard disk installation, refer to the
instruction manual supplied with the hard disk case.

Power indicator

SD CARD button

4

Basic Connections VCC-HD5400

*2 *1

*1

HDMI

USB

LAN

󱤨

󱤩

󱤪

󱤫

Alarm cable

󱤬

Audio cable

󱤭

Power cable

󱤮

Control cable

BROWN

ALARM_IN1

RED

ALARM_IN2

ORANGE

ALARM_IN3

ALARM_IN4

YELLOW

BLACK

ALARM_OUT1

WHITE

ALARM_OUT2

GRAY

BLACK

WHITE

AUDI O IN

BLACK

AUDIO OUT

DC12

RED + ~

-

BLACK

WHITE

NC GND

RS485(A)

GRAY

YELLOW

RS485(B)

WHITE

GND

GND

GND

AC24

~

High-definition
monitor

HDD

*3

PC

External
peripheral device

Microphone

Speaker

~

~

AC24

GND

+

-

①

DC12

②

System controller

Video cable

Before attempting the following connections, be sure to turn off all

*2

•

components of your system.

•

Improper connection may cause smoke or failures. Before attempting to

Monitor

connect each system component, carefully read the instruction manual
that comes with it to familiarize yourself with the correct connection
procedure.

󱤨 High-Definition Monitor Connection

Connect the HDMI cable to the HD video output terminal (HDMI).

You cannot output the video simultaneously from HD video output terminal (HDMI) and from
monitor output terminal (MONITOR OUT). When both terminals are used, the HD video output
terminal takes precedence.

5

VCC-HD5400P

*1

*1

*2 *1

HDMI

USB

LAN

*2

󱤨

󱤩

󱤪

󱤫

Alarm
cable

󱤬

Audio cable

󱤮

Control cable

BROWN

RED

ORANGE

YELLOW

BLACK

WHITE

GRAY

BLACK

WHITE

BLACK

GRAY

YELLOW

WHITE

ALARM_IN1

ALARM_IN2
ALARM_IN3

ALARM_IN4

GND

ALARM_OUT1

ALARM_OUT2

GND

AUDI O IN

AUDIO OUT

RS485(A)

RS485(B)

GND

High-definition
monitor

HDD

*3

PC

External
peripheral device

Microphone

Speaker

Video cable

󱤭

Power cable

BLACK

WHITE

Monitor

DC12

RED + ~

-

NC GND

AC24

~

System controller

~

~

AC24

GND

+

DC12

-

󱤩 Connecting an External Hard Disk

Put the hard disk in a dedicated hard disk case (VA-HDC4000, sold separately) and then connect
the case to the camera.
*3: Connect the mini-USB (type B) connector of the USB cable to the camera, connect the other

connector (type A) of the cable to a commercially-available USB adapter (female A to male
mini B), and connect the adapter to the hard disk case.

6

①

②

Basic Connections

Network Connection

󱤪

This camera is designed so that you can use all of its functions via network operation.
By connecting the network (LAN) socket of the camera to your PC using a LAN cable, you can
configure and operate it from the Web browser installed on your PC.

Internet
connection

LAN connection

Switching hub

Use a LAN cable no longer than 100 m (109.4 yards) with the shield type CAT5 or higher.

•

•

Use a straight-type cable if connecting to LAN, and use a cross-type cable if directly connecting the
camera to a PC.

•

The supported Web browser is Internet Explorer Ver.6.0 SP2 or higher, or Internet Explorer Ver.7.0.

About the internet connection

■

PC

Router

Internet

Modem

PC

Port forwarding for the video port must be enabled on the broadband router.
For details on how to set port forwarding, please refer to your router’s Instruction manual.

Port number (default): 80 (TCP)
IP address (default): 192.168.0.2

To LAN port

Router

To connect two or more cameras, via network operation on the NETWORK SETTINGS screen, assign
them with port numbers that are different from that of the first camera. (

Using PoE

■

Port number (default): 80 (TCP)

• Set to same value as on LAN

To WAN port

Modem

Electronic manual)

This camera supports PoE (Power over Ethernet). This means that you can install the camera in
locations where there is no 24 VAC/12 VDC power outlet nearby.

If you are using PoE, do not use the camera’s power terminals (24 VAC/12 VDC).

•

•

Do not power the PoE hub or PoE power adapter until you finish connecting the camera.

•

When the PoE power supply is used, you cannot record video to an external hard disk drive.

You can use a PoE-compatible switching hub to extend the transmission distance.
For details on the extendable distance, please refer to the hub performance in the specifications, etc.

For how to connect the PoE power supply, refer to the electronic manual.

7

Basic Connections

Alarm Cable Connection

󱤫

Use a thicker cable than 24AWG for connection. (Maximum length 600 m/656 yds.)

① Outputting alarm signals (ALARM OUT1-2)

Connect a buzzer, lamp, or other alarm device to the alarm output cable.
Alarm can be output via two channels.

( Electronic manual)

•

After connecting an alarm device, configure the output conditions for the corresponding alarm
output cable via network operation on the ALARM SETTINGS screen.

•

Configuration of alarm output terminal is also possible via remote operation. For that, set
[ALARM OUT] to “REMOTE” on the ALARM SETTINGS screen.

Inputting alarm signals (ALARM IN1-4)

②

Connect an alarm switch, infrared sensor, or other device to detect alarm conditions to the
alarm input cable.
Up to four independent alarm input channels are available.

( Electronic manual)

•

After connecting an alarm device, configure the input conditions for the corresponding alarm
input cable via network operation on the ALARM SETTINGS screen.

•

To use the alarm input terminals as color/black-and-white mode switching terminals, follow the
steps below.

•

Under CAMERA SETTINGS, set [DAY/NIGHT] to “COLOR” and select the cable you want to use

in [EXT ALARM].

•

On the ALARM SETTINGS screen, in [POLARITY], select the signal polarity of the alarm input

terminal.

•

If you connect an external switch to ALARM IN1 terminal, you can specify time by controlling
the switch. In this case, configure the [CLOCK IN] setting via network operation on CLOCK
SETTINGS screen.

󱤬 Audio Jack Connection

AUDIO IN Jack (White)

•

Use this jack to connect an optional external microphone to listen to the sound while monitoring
the surveillance video, or simultaneously record the video and sound.

•

AUDIO OUT Jack (Black)

Connect this jack via an audio cable to the audio input jack of an amplified speaker system or the
monitor.

This terminal is compatible with mono microphone with 3.5-mm jack or line mono signals (only
the left channel in cases of stereo signals).

󱤭 Power Connection

Connect the power terminals (24 VAC/12 VDC) of the camera to a power supply.

① Connection to 24 VAC power supply

Although the power terminals have no polarity, the earth grounding wire must be connected to
the GND (earth grounding) terminal.

② Connection to 12 VDC power supply

Note the polarity (+/–) of the power terminals when connecting the camera to a 12 VDC power
supply.
Incorrect polarity may cause damage to the camera.

Be sure to use an 18AWG or thicker wire power cable.

•

•

If you must use a long power cable, determine the cable type by ensuring that the voltage at the
24 VAC/12 VDC terminal is within the operating range of the camera.

•

If you are using PoE, do not use the camera’s power terminals (24 VAC/12 VDC).

󱤮 Connection of controller

By connecting a system controller (sold separately), the camera can be controlled remotely.

Configure the protocol, baud rate and address. (Refer to “Control/Address Settings” Page 11).

8

Installation

Using the supplied pattern sheet, drill the holes for the cables and screws.

󱳛

Pull out the cables from the ceiling.•

Attach the supplied mounting plate to the ceiling using commercially-available screws.

󱳝

(Screw: M4/No. 8 or equivalent) Length: 40 mm/1.6 in or more, Head: φ 8.3 mm/0.3 in

•

Loosen the screw (A) and remove the cable holder (B).

(B)

(A)

Hook the safety cable attached on the camera base to the mounting plate.

󱳟

Connect the cables from the ceiling to the camera cables. ( Page 5 “Basic Connections”)

󱳡

① After connecting each of the terminals (LAN, USB, HDMI), put the cable holder (B) back to its

original position so as to hold all the cables in place, and tighten the screw (A).

② Using the supplied fixer (C), tidy the wiring by binding all the cables to make the installation

easier.

(B)

(A)

After binding, cut off the
excess portion of the fixer.

When routing cables through the side face of the camera

Remove the wire gutter cover (AA).

If you use a USB cable or an HDMI cable,
secure it along with the LAN cable using the
supplied fixer (C) so that the cables don’t
easily come off.
When you route the cables after installing
the camera, be sure to carefully handle the
cables so as not to strongly pull them.

(AA)

9

(C)

(C)

Installation

󱳛

Pattern sheet (supplied)

Ceiling

󱳟

󱳝

󱳣

(D)(D)

Mount the camera by aligning the triangular marks (▲), then rotate the camera in the arrow

󱳣

(D) direction.

Make sure the camera is securely mounted.•

Open the side cover and tighten the fall-prevention screw (E) using the supplied hexagonal

󱳥

wrench (F).

When fi nished, make sure to put the cover back.

•

󱳡

(F)

(E)

The surface of the camera can be hot during operation, but it is not a malfunction.

•

When you touch the heated portion of the camera for a long time during installation, adjustment or
dismounting, you may get a low-temperature burn.

•

SD card may be hot immediately after use. When you remove a SD card from the camera, be
absolutely sure to turn it off and wait until it is completely cooled down.

10

Control/Address Settings

When you connect the camera to a controller, it is necessary to configure the interface board control
switch and address switch.

Control switch

■

This is used to configure transmission rate and protocol, etc.

Switches 2 and 3 are not used.

•

•

Settings in bold typeface in the table below show the factory default
configurations.

Baud Rate

❶

Configure the transmission rate of connected devices to the transmission

rate of the camera.

Transmission Rate Switch 6 Switch 5

2400 OFF OFF

4800 ON OFF

9600 OFF ON

19200 ON ON

When protocol is set to “PELCO”, set to 2400.

❷ Protocol

Select the protocol for controlling the camera.

Protocol Switch 4 Corresponding Protocol

SSP (SANYO) OFF Automatic switching between Sanyo SSP and high speed SSP

PELCO ON Automatic switching between PELCO-D and PELCO-P

ON

ON

654321

654321

❶❷ ❸

❶❷ ❸

❸ Terminator

When you connect multiple cameras, set the terminator setting (Switch 1) of the final device to “ON”

and all other devices to “OFF”.

■

Address switch

If you use the RS485 communication mode, assign a unique address (camera No.) to each camera.

Configure the address by setting the dip switches to “ON” and “OFF”.

For further information, refer to the “Address Settings Table” on
the next page.

ON

12345678

11

Address Settings Table

In the table, the circle mark “○” means ON. Set switches as shown in the table.

When protocol is “SSP (SANYO)”:

•

Configurable addresses: 1 to 127

•

Switch 8 is configured to “OFF”.

When protocol is “PELCO”:

•

Configurable addresses: 1 to 255

•

To configure the address to a number between 128 and 255, set
the switch 8 to “ON”.

ON

1 2345678

Address (Camera No.)

Protocol

SANYO

PELCO 1234567
– – 128
1 1 129
2 2 130
3 3 131
4 4 132
5 5 133
6 6 134
7 7 135
8 8 136
9 9 137

10 10 138
11 11 139
12 12 140
13 13 141
14 14 142
15 15 143
16 16 144
17 17 145
18 18 146
19 19 147
20 20 148
21 21 149
22 22 150
23 23 151
24 24 152
25 25 153
26 26 154
27 27 155
28 28 156
29 29 157
30 30 158
31 31 159
32 32 160
33 33 161
34 34 162
35 35 163
36 36 164
37 37 165
38 38 166
39 39 167
40 40 168
41 41 169
42 42 170

○

○○

○○

○○○

○○

○○ ○

○○○

○○○○

○○

○○ ○

○○○

○○○ ○

○○○

○○ ○○

○ ○○○

○○○○○

○○

○○ ○

○○ ○

○○○ ○

○○○

Switch No.

○

○

○○

○

○○

○○

○○○

○

○○

○○

○○ ○

○○

○○○

○○○

○○○○

○

○○

○○

○○ ○

○○

○○○

Address (Camera No.)

Protocol

SANYO

PELCO 1234567
43 43 171
44 44 172
45 45 173
46 46 174
47 47 175
48 48 176
49 49 177
50 50 178
51 51 179
52 52 180
53 53 181
54 54 182
55 55 183
56 56 184
57 57 185
58 58 186
59 59 187
60 60 188
61 61 189
62 62 190
63 63 191
64 64 192
65 65 193
66 66 194
67 67 195
68 68 196
69 69 197
70 70 198
71 71 199
72 72 200
73 73 201
74 74 202
75 75 203
76 76 204
77 77 205
78 78 206
79 79 207
80 80 208
81 81 209
82 82 210
83 83 211
84 84 212
85 85 213

○○○○

○○○○

○○○○ ○

○○○

○○ ○○

○○○○

○○○ ○○

○ ○○○

○○ ○○○

○ ○○○○

○○○○○○

○○

○○ ○

○○ ○

○○○ ○

○○○

○○ ○ ○

○○○ ○

○○○○ ○

○○○

○○ ○ ○

○○○○

Switch No.

○○ ○

○○○ ○

○○

○○○

○○○

○○ ○○

○○○

○ ○○○

○○○○

○○○○○

○○

○○

○○ ○

○○

○○ ○

○○ ○

○○○ ○

○○

○○○

○○○

Address (Camera No.)

SANYO

86 86 214
87 87 215
88 88 216
89 89 217
90 90 218
91 91 219
92 92 220
93 93 221
94 94 222
95 95 223
96 96 224
97 97 225
98 98 226

99 99 227
100 100 228
101 101 229
102 102 230
103 103 231
104 104 232
105 105 233
106 106 234
107 107 235

○

108 108 236
109 109 237
110 110 238
111 111 239
112 112 240
113 113 241
114 114 242
115 115 243
116 116 244
117 117 245
118 118 246
119 119 247
120 120 248
121 121 249
122 122 250
123 123 251
124 124 252
125 125 253
126 126 254
127 127 255

Protocol

PELCO 1234567

Switch No.

○○○○

○○○○○

○○ ○

○○○○

○○○○

○○ ○○ ○

○○○ ○

○ ○○○ ○

○○○○ ○

○○○○○ ○

○○○

○○○

○○ ○○

○○○

○○ ○○

○○ ○○

○○○ ○○

○○○

○○○○

○○○○

○○ ○ ○○

○○ ○○

○○○○○

○○○ ○○

○○○○ ○○

○ ○○○

○ ○○○

○○ ○○○

○ ○○○

○ ○ ○○○

○○ ○○○

○○○ ○○○

○○○○

○ ○○○○

○ ○○○○

○○ ○○○○

○○○○○

○ ○○○○○

○○○○○○

○○○○○○○

○○

○○○

12

Network Settings

Preparing Your Computer for Network Operation

Check your operating environment. ( Page 1)

󱳛

Connect the camera to the network to which your PC is also connected.

󱳝

Configue the network information on your PC.

󱳟

Configure information such as the IP address of your PC.

Install the “H.264 Plug-in” from the supplied CD-ROM onto your PC.

󱳡

You are now ready to monitor the surveillance video in the H.264 format.

Start Internet Explorer.

󱳣

The supported Web browser is Internet Explorer Ver.6.0 SP2 or higher, or Internet Explorer Ver.7.0.

Access the camera from your Web browser.

󱳥

From your Web browser (Internet Explorer), access the camera and log into the system as an
“admin” user (administrator).

In the address bar, type the IP address of the camera and press [Enter] key.

󱳧

When you access the camera, the login screen appears.
If this is the first access to the camera, in the Address bar, enter the default IP address as follows.

If you set [SSL] to “ON”, before the IP address, type “https://” (instead of “http://”).
Attempts to access the camera using the default IP address will fail if that address is already
being used by another device in the network.
If so, change the IP address of the existing device before accessing the camera.

Type your user name and password and click [OK].

󱳩

The language selection screen appears.

If this is the first access to the camera, log in as an admin user (administrator) using the following
default authentication information.

•

User name: admin

•

Password: admin

Click the button corresponding to the language you want to use.

󱳫

The live screen appears.
From the second login onwards, the live screen appears automatically by skipping the language
selection screen.
If this is the first access to the camera, configure the system clock on the CLOCK SETTINGS
screen.

13

Specifications

■

Camera

Image pickup device 1/2.5" CMOS sensor
Effective pixels 16:9 1920 (H) × 1080 (V), 4:3 1600 (H) × 1200 (V)
Lowest image

illumination
Video S/N ratio 50 dB or higher (when AGC is ‘OFF’)
Lens Focal Length: f=6.3 - 63 mm, F number: F1.8 - 2.5

Rotational scope Pan: 360° endless pan

Rotation speed Pan: Max. 350°/sec

Preset position Max. 256
Auto mode Sequential, auto pan, tour, automatic return
Privacy mask ON/OFF, up to 32 positions
Motion sensor ON (detection area setting, video analytics)/OFF, face detection function
Auto pursuit ON/OFF
Sway compensation ON/OFF
Language selection English, French, German, Spanish, Japanese

For further details on the specifications of the camera, refer to the electronic manual.

■

I/O

Video output HD Output: HDMI terminal (TYPE C)

LAN 10BASE-T/100BASE-TX (RJ-45 connector)
EX-HDD Connector For connecting an external hard disk drive case
SD Card Slot 1 (SDHC compliant, max. 32 GB supported)
Alarm input 4 (NO/NC), also used for switching between day and night modes
Alarm output 2 (NO/NC, 16V, 150 mA, open collector)
Audio input/output Audio input (white: 3.5-mm mini jack)

Communication method RS-485
Protocol SSP, PELCO-D
Baud Rate 2400, 4800, 9600, 19200
Address 1 - 255 (sanyo SSP: 1 to 127)

50IRE: 2.0 lx (F1.8, in color mode with high gain)
50IRE: 0.1 lx (F1.8 in black-and-white mode with high gain)

Optical zoom 10x, electronic zoom 16x (up to 160x when used in
combination with the optical zoom)

Tilt: –20 to +200°

Tilt: Max. 350°/sec (0.1° - 120°/ sec for manual operation)

Monitor output: BNC terminal (MONITOR OUT)

Audio output (black: 3.5-mm mini jack)

■

Recording media

SD memory card
External HDD

For the recommended SD memory cards or hard disks, visit our website.

http://www.sanyosecurity.com/

Normal recording, alarm recording, backup video recording in event of a
network failure, log information

14

Specifications

■

Network

Image/video compression H.264/JPEG
Video size (H.264) (16:9) 1920×1080, 1280×720, 640×360, 320×180

Video size (JPEG) (16:9)1920×1080, 1280×720, 1024×576, 640×360

Picture quality QUALITY mode: BASIC, NORMAL, ENHANCED, FINE, SUPER FINE

Interface 10BASE-T/100BASE-TX
Protocol TCP/IP, UDP, HTTP, HTTPS, SMTP, NTP, DHCP, FTP, DDNS, RTP, RTSP,

Audio G.711 (Bidirectional)
Simultaneous access 20
Security BASIC authentication (ID/password), SSL, IP filtering

■

Others

Operating ambient
temperature/humidity

Power source VCC-HD5400:

Power consumption 21 W (PoE: 12.3 W)
Weight 1350 g
Dimensions Unit: mm (inch)

(4:3) 1600×1200, 1280×960, 1024×768, 640×480, 320×240

(4:3) 1600×1200, 1280×960, 1024×768, 800×600, 640×480, 320×240

BITRATE mode: User-specified bit rate

RTCP

–10 to +50°C/14 to 122°F, 90% RH or less (no condensation)

•

12 to 15 VDC

•

24 VAC±10%, 60 Hz

•

PoE

VCC-HD5400P:

•

12 to 15 VDC

•

24 VAC±10%, 50 Hz

•

PoE

F124 (4.88)

153 (6.02)

Appearance and specifications are subject to change without prior notice or obligations.

15

Copyright Notice

The instruction manual and the software are copyrighted by SANYO Electric Co., Ltd. No materials
contained in the manual and the software may, wholly or partially, be copied, modified, reproduced, or
distributed in any format without the prior permission of the copyright holder.
Microsoft, Windows, ActiveX and Internet Explorer are registered trademarks or trademarks of
Microsoft Corporation in the United States and other countries.
The official name for “Windows” used in this manual is Microsoft
In this manual, note that the word “Windows” refers to both “Microsoft® Windows® XP Operating
System” and “Microsoft® Windows® Vista Operating System”.
Intel and Pentium are registered trademarks or trademarks of Intel Corporation and its subsidiaries in
the United States and other countries.
IBM and IBM PC/AT are trademarks of International Business Machines Corporation.

HDMI, the HDMI Logo and High-Definition Multimedia Interface are trademarks or registered
trademarks of HDMI Licensing LLC.

SDHC Logo is a trademark.

All other brands and product names in this manual are the registered trademarks or trademarks of
their respective owners.

Notes on data storage

■

It is recommended that important data be copied to a separate medium.

•

In the following situations, it is possible that recorded data may be lost (destroyed). Our company

•

bears absolutely no responsibility for damages or profi ts loss due to the loss of data.

• The medium (SD card or external hard disk) is not used correctly.

• The medium is not installed on the device correctly.

• The medium is subjected to electrical or mechanical shock.

• The card is removed or the power is turned off while the card is being accessed.

• The medium has reached the end of its service life.

®

Windows® Operating System.

License for Software Contained in CD-ROM

■

Please read carefully the terms and conditions contained in the license agreement that appears

•

on the screen during the software installation process. Provided that you have agreed to all the
terms and conditions therein, you may use the software subject to the license agreement.
For information on the other products or services provided by third parties which are introduced in

•

the CD-ROM, please contact each supplier or manufacturer.

16