Sanyo VCC-3770P Instruction Manual

Download

Page 1

INSTRUCTION MANUAL BEDIENUNGSANLEITUNG MANUEL D’INSTRUCTIONS



COLOUR CCD Camera CCD-Farbkamera Caméra CCD COULEUR



CCD



VCC-3700P VCC-3770P

About this manual

• Before installing and using the camera, please

read this manual carefully. Be sure to keep it handy for later reference.

• This manual gives basic connections and

operating instructions for 2 PAL models (VCC-3700P, 3770P).

À propos de ce manuel

• Avant d’installer et d’utiliser la caméra, veuillez

lire ce manuel attentivement. Gardez-le à portée de main pour toute référence ultérieure.

• Ce manuel couvre les branchements et

instructions pour l’utilisation de base pour 2 modèles de format PAL (VCC-3700P et 3770P).

Über diese Bedienungsanleitung

• Lesen Sie bitte vor der Montage und dem

Inbetriebnehmen der Kamera zuerst diese Bedienungsanleitung sorgfältig durch und bewahren Sie sie zum späteren Nachschlagen auf.

• In dieser Anleitung finden Sie die Anschlüsse

und die Grundbedienung für 2 PAL-Modelle (VCC-3700P und 3770P)



•

   !

•

"#2$

3770P)

&'()*+,-!

PAL% (VCC-3700P,

Page 2

Depending on the conditions of use, installation and environment, please be sure to make the appropriate settings and adjustments. If you need help with installation and/or settings, please consult your dealer.

CONTENTS

PRECAUTIONS...................................................2

PARTS NAMES...................................................3

MOUNTING THE LENS......................................5

CONNECTIONS..................................................7

SETTINGS...........................................................9

TROUBLESHOOTING.......................................13

SPECIFICATIONS .............................................13

ACCESSORIES

1 C mount adaptor (5 mm)................ 1 pc.

The C mount adaptor must be used to be able to install a C mount lens on the camera.

2 Lens iris plug (4-pin) ........................1 pc.

FEATURES

• Built-in interline transfer method 1/3"

CCD – Model VCC-3700P approx. 320,000

picture elements

– Model VCC-3770P approx. 470,000

picture elements

• Low smear, anti-blooming, low lag, no

burning and no geometric distortion using the CCD solid state image device.

• 100% solid state components giving

excellent immunity to shock and vibration

• Not subject to interference from

magnetic or electrostatic fields

• High sensitivity, minimum required

illumination – Model VCC-3700P 1.4 lux with F 1.2

lens

– Model VCC-3770P 2 lux with F 1.2

lens

• Horizontal resolution

– Model VCC-3700P more than 330 TV

lines

– Model VCC-3770P more than 460 TV

lines

• Built-in high speed electronic shutter

(with selectable speed setting by internal switches)

• New backlight compensation function

(Active when using an auto-iris lens)

• Externally adjustable flange back

(mechanical focus)

• Low power consumption and quick start

• Separate Y and C signal outputs: Model

VCC-3770P only

English 1

Page 3

PRECAUTIONS

In case of problem

Do not use the camera if smoke or a strange odour comes from the unit, or if it seems not to function correctly. Disconnect the power cord immediately, and consult your dealer (or a Sanyo Authorized Service Centre).

Do not open or modify

Do not open the cabinet, as it may be dangerous and cause damage to the unit. For internal settings and repairs, consult your dealer (or a Sanyo Authorized Service Centre).

Do not put objects inside the unit

Make sure that no metal objects or flammable substance get inside the camera. If used with a foreign object inside, it could cause a fire, short-circuits or damages.

If water or a liquid gets inside the camera, disconnect the power cord immediately, and consult your dealer (or a Sanyo Authorized Service Centre). Be careful to protect the camera from rain, sea water, etc.

Be careful when handling the unit

To prevent damages, do not drop the camera or subject it to strong shock or vibration.

Install away from electric or magnetic fields

If installed close to a TV, radio transmitter, magnet, electric motor, transformer, audio speakers the magnetic field they generate will distort the image.

Protect from humidity and dust

To prevent damages to the camera, do not install it where there is greasy smoke or steam, where the dampness may get too high, or where there is a lot of dust.

Protect from high temperatures

Do not install close to stoves, or other heat generating devices, such as spotlights, etc., or where it could be subject to direct sunlight, as that could cause deformation, discoloration or other damages.

Be careful when installing close to the ceiling, in a kitchen or boiler room, as the temperature may raise to high levels.

Install where the temperature range will stay between –10˚C and 50˚C. (no condensation)

Cleaning

• Dirt can be removed from the cabinet

by wiping it with a soft cloth. To remove stains, wipe with a soft cloth moistened with a soft detergent solution and wrung dry, then wipe dry with dry soft cloth.

• Do not use benzine, thinner or other

chemical product on the cabinet, as that may cause deformation and paint peeling. Before using a chemical cloth, make sure to read all accompanying instructions. Make sure that no plastic or rubber material comes in contact with the cabinet for a long period of time, as that may cause damage or paint peeling.

ENGLISH

2 English

Page 4

PARTS NAMES

(VCC-3700P)

(VCC-3770P)

1 Shorter screws: M3 x 4 2 Longer screws: M3 x 6 3 Camera mounting screw

hole: 1/4"-20 UNC

1 Power indicator (POWER)

Comes on when the power to the camera is on.

2 Video output connector (VIDEO OUT: BNC type)

Connect this connector to a device such as a VCR or monitor with a VIDEO IN connector.

3 AC power cord 4 External sync composite video signal input connector

(VBS IN: BNC type)

Connect to this connector the synchronizing signal output from a synchronizing signal device or the composite signal of a video distributor.

5 Line phase adjustment screw (LINE PHASE)

When using two cameras or more, the image on the monitor may roll vertically when switching sources. This rolling can be minimized by turning this screw.

6 Y/C OUT connector (4 pin)

Separate Y (luminance) and C (chroma) signals are output from this terminal. A better picture quality is obtained if the monitor or VCR is connected to this connector.

1 Y signal ground 2 C signal ground 3 Y signal: 1.0 Vp-p, 75 ohms, unbalanced, negative sync 4 C signal: 0.3 Vp-p, 75 ohms, unbalanced

7 Lens mount cap

The cap is installed to protect the lens mount section. Remove the lens mount cap before installing a lens (sold

separately).

8 Camera installation bracket

The bracket can be fixed at the top or bottom of the camera. When fixing the bracket, be sure to use the longer screws and install the shorter screws on the opposite side to seal the openings.

CAUTION:

When installing the camera support, select a location that can support the total weight of the camera and accessories.

English 3

Page 5

9 Lens iris output connector (4 pin)

This 4-pin connector is used to send the DC control signal and power supply to an auto-iris type lens.

F Camera setup section (under the cover)

This unit factory settings are as indicated below. These settings are for when using a 1/3 inch CS mount DC (without EE internal amplifier) type lens. However, if due to installation conditions or environment the settings may need

to be modified for best results (see page 9 "SETTINGS"). To access the controls, remove the cover fixing screw, then remove the cover.

bcdfg

VR311

H-P

SC-P2

OFF

L-L

VR312

INT

AGC FL

SYNC

SC-P1

VR301

O F F

VR302

VR303

LEVEL

OFF

BLC

DC VIDEO

A. I.

LENS

Control name Position Auto gain control switch (AGC) Internal/Line lock switch (SYNC) High speed electronic shutter

switches (E.S.) White balance switch (WB) Red and Blue colour

ON INT

All OFF: 1/50 sec

about centre

adjustment volume (R, B) Electronic iris (EI)/

OFF

Backlight compensation (BLC) switch

Auto-iris lens switch (A.I. LENS)

Lens iris level volume (LEVEL)

about centre

Note:

• The EI/BLC switch is used for an auto-iris lens, therefore

the two settings cannot be used simultaneously.

• When using a 1/2 or 2/3 inch C mount VIDEO (with EE

internal amplifier) auto-iris type lens, set the A.I. LENS switch to the VIDEO position.

4 English

Page 6

PARTS NAMES

G Flange-back adjustment screw (FLANGE BACK ADJ.)

H Flange-back lock screw (FLANGE BACK LOCK)

Flange-back adjustment

If the pick-up surface is not correctly positioned with relation to the lens focal point, the picture will be out of focus (in

ADJ.

LOCK

particular when using auto-iris power zoom lenses, sold separately). If that is the case, adjust the flange-back position as described below.

1 Using a + screwdriver, loosen the FLANGE BACK LOCK

screw (M2:+). Set the zoom lens to the maximum telephoto position, set the focus using the focus ring on the lens.

2 Set the zoom lens to the maximum wide angle position,

set the focus using the FLANGE BACK ADJ. screw.

3 Repeat steps 2 and 3, until the image stays in focus when

changing from a telephoto shot to a wide angle shot. When the setting is complete, tighten the FLANGE

BACK LOCK screw.

MOUNTING THE LENS

Check the lens mount

Do not use a lens if the length “ That may damage the camera and prevent proper installation.

Installation of a DC type auto-iris lens (sold separately)

A 1/3 inch CS mount type lens without EE amplifier circuit that only uses a DC power source. This camera can receive (the A.I. LENS switch to the DC type) a CS mount type lens without the need of an adaptor.

If the lens plug shape or wiring does not correspond, please install the supplied plug as indicated in the pin layout table.

L” is more than 5 mm.

English 5

Page 7

MOUNTING THE LENS

Installation of a VIDEO type auto-iris lens

2 (A)

(B)

DC VIDEO

(sold separately)

A 1/2 or 2/3 inch C mount type lens with EE amplifier circuit that uses the video signal and a DC power source.

1 Remove the lens mount cap. 2 Attach the supplied C mount adaptor (A) to the

auto-iris lens (B), then install the assembly on the camera.

3 Connect the lens plug to the LENS connector on the side

of the camera. If the lens plug shape or wiring does not correspond to the specifications below, connect the supplied plug as indicated.

• When using lenses from other makers, make sure that

the pins connections in the plug correspond to the ones of the camera.

Refer to the lens specifications to check the pins connections in the plug.

• If they are different than indicated, remove the original

plug and connect the supplied plug according to the diagram.

4 Set the A.I. LENS switch in the camera setup section to

the VIDEO position.

Pin layout

DC type lenses VIDEO type lenses

Brake coil (–) +12 V DC (50 mA max.)

Brake coil (+) Not used

Drive coil (+) Video output (1.0 Vp-p, high

Drive coil (–) Ground (for video signal and DC

impedance)

power)

6 English

Page 8

MOUNTING THE LENS

If using Sanyo (DC type) auto-iris lens

• VCL-CS8LY: Standard angle, f= 8 mm

• VCL-CS4LY: Wide angle, f= 4 mm

• VCL-CS2LY: Ultra-wide angle, f= 2.8 mm

If using a VIDEO type auto-iris lens

• Set the ALC and LEVEL controls on the lens to adjust the

iris. Normally the ALC volume should be turned all the way to Av (Average).

• Depending on the type of lens used, the lens may not

perform properly. In such a case, adjust the LEVEL volume on the lens casing to correct.

Compatible auto-iris lenses

• f= 9 mm (Standard angle), f= 12 mm (Telephoto),

f= 16 mm (More telephoto)

CONNECTIONS

(VCC-3700P)

(A)

(Video signal connections)

: VIDEO IN : VIDEO OUT

English 7

Basic connection for monitoring or recording

The peripheral devices (VCR, monitor, lens, etc.) and cables are sold separately.

1 Make the video signal connection between the camera

and the monitor or time lapse VCR.

2 Insert the plug of this power cord into a wall outlet.

The POWER indicator (A) will light. Adjust the picture on the monitor using the Brightness and Contrast controls.

Coaxial cable type and maximum length

• Cable type RG-59U, 100 m maximum.

• Cable type RG-39U, 200 m maximum.

CAUTION:

The RG-59U type cable should not be run through electrical conduits or through the air.

Page 9

CONNECTIONS

(VCC-3770P)

(A)

(Video signal connections)

: Y/C or S-VIDEO IN : Y/C or S-VIDEO OUT

Connections to the camera Y/C OUT connector

The peripheral devices (VCR, monitor, lens, etc.) and

cables are sold separately.

1 Using a coaxial cable (twin type, 75 ohms), connect the

Y/C OUT connector from the camera to the S-VIDEO input terminal on the monitor or time lapse VCR.

2 Insert the plug of this power cord into a wall outlet.

Then, turn on the power of all the devices connected to the camera. The POWER indicator (A) will light. Adjust the picture on the monitor using the Brightness and Contrast controls.

CAUTION:

• Please use a monitor with a Y/C or S-VIDEO input

terminal, or a time lapse VCR with a S-VIDEO input terminal.

• Use a Mini-DIN (round type, 4-pin) plug to connect to the

Y/C connector. Never use a coaxial cable longer that 10 metres to connect the camera to the S-VIDEO input terminal.

8 English

Page 10

SETTINGS

VR311

H-P

SC-P2

SC-P1

OFF

L-L

VR312

INT

AGC FL

SYNC

O N

O F F

VR303

VR302

OFF

BLC

AGC setting

AGC (Automatic gain control) can be turned ON or OFF.

ON: Auto gain control OFF: Fixed gain

Line phase adjustment

When using a camera switcher to connect 2 cameras or more to one monitor, there may be a vertical roll of the images when switched. In such a case, set as described below.

1 Set the SYNC switch to the L-L position. 2 Switch the display on the monitor from camera 1 to camera 2.

Adjust the LINE PHASE volume on camera 2 until the vertical roll of the image stops. If more than two cameras are used, please repeat this procedure for all the cameras.

CAUTION:

If the vertical roll cannot be corrected by setting the LINE PHASE volume on camera 2, try setting the LINE PHASE volume on camera 1. If it still cannot be corrected, please check that the polarity of the power cords of all connected devices is correct.

VR301

LEVEL

DC VIDEO

A. I.

LENS

OFF

AGC

L-L

INT

SYNC

English 9

Page 11

SETTINGS

High speed electronic shutter setting

Normally, the speed setting switches for the high speed ES (electronic shutter) are all set to the OFF position. This sets the electronic shutter speed to 1/50 sec. The switches can be set as indicated in table A to select one of the 8 speeds available.

CAUTION:

• When using the high speed electronic shutter, the EI/BLC

switch must be set to the OFF position.

• Using the high speed electronic shutter indoors with low

lighting, will give darker pictures. In such a case, add some lights to make sure the lighting is sufficient. If the lighting is very bright, pay attention to the light angle in order to avoid or minimize the smear phenomenon effect.

White balance adjustment

Normally the WB (white balance) switch is set to the A (automatic) position and the white balance is adjusted automatically. If a manual white balance adjustment is necessary, follow the steps below.

Set the WB switch to the M (manual) position, then adjust the colour.

• Turn R (VR303) to set the red ratio and/or B (VR302) to set the

blue ratio.

Table A

1/50 sec.

1/120 sec.

1/250 sec.

1/500 sec.

1/1000 sec.

1/2000 sec.

1/4000 sec.

1/10000 sec.

O N

O F F

VR303

VR302

2341

10 English

Page 12

Electronic iris function setting

Use a manual or fixed iris lens and set the lens aperture to the

OFF

BLC

shortest F stop. Set the EI/BLC switch to EI (electronic iris)-ON position.

The dynamic range of the electronic iris will be as indicated in table

CAUTION:

• The electronic iris is suitable for normal indoor use. When the

EI/BLC switch is set to the EI-ON position, do not use an auto-iris lens.

• If used under fluorescent light, the image may flicker. In such a case, change to

incandescent lighting or set the EI/BLC switch to the OFF position and use an auto-iris lens.

• When shooting bright subjects, pay attention to the light angle in order to avoid or

minimize the smear phenomenon effect.

When using an auto-iris lens (for indoor/outdoor use)

Set the EI/BLC switch to the OFF position.

CAUTION:

If conditions are outside the electronic iris operation range or more than the maximum illumination, it will cause saturation of the CCD. In that case, use a manual iris lens.

Table B

Model F stops Minimum illumination Maximum illumination

VCC-3700P

VCC-3770P

F 1.2 F 1.4 F 1.2 F 1.4

1.4 lux 70,000 lux

1.9 lux 95,000 lux 2 lux 100,000 lux

2.7 lux 130,000 lux

English 11

Page 13

SETTINGS

Backlight compensation setting

Use an auto-iris lens and set the EI/BLC switch to the BLC (backlight compensation)-ON position, to engage the backlight compensation function.

Use an auto-iris lens. Set the EI/BLC switch to BLC-ON position.

OFF

BLC

If using a VIDEO type auto-iris lens

• The ALC volume on the lens should be turned all the way to Av (Average).

• If the backlight compensation function does not compensate properly for the conditions,

set using the LEVEL volume on the lens.

CAUTION:

The electronic iris function and the backlight compensation function cannot operate simultaneously.

Lens iris adjustment

If using a DC type auto-iris lens, you will need to set the LEVEL (VR301) volume when shooting in the conditions described below.

L (counterclockwise): To decrease the contrast H (clockwise): To increase the contrast

• If shooting simultaneously in a dark room and through a bright

window.

• If the subject background is extremely bright or dark.

• If the brightness of the picture on the monitor is not correct.

VR301

LEVEL

12 English

Page 14

TROUBLESHOOTING

Before taking the camera for repairs, please check below to make sure that the camera is used correctly. If it still does not perform correctly, please consult your dealer or a Sanyo Authorized Service Centre.

No picture on the monitor screen

• Is the power turned on to all connected devices? Is the voltage correct?

• Are all the signal connecting cables correctly connected?

• Is the lighting sufficient?

• Has the lens cap been removed?

• Is the lens type (DC or VIDEO) correctly selected?

Depending on the type of lens, the A. I. LENS switch must be set accordingly.

• Is the iris control correctly set?

A: When using a DC type lens, the LEVEL volume (inside the camera casing) should be

adjusted.

B: When using a VIDEO type lens, the LEVEL volume (on the lens) should be adjusted.

The picture is not clear

• Is the monitor correctly adjusted?

• Is the flange-back position correctly set?

• Is the lens focus correctly adjusted?

• Are the lens surfaces clean?

If there is dust or finger prints on the lens, the image quality will deteriorate. To clean the lens use a soft cloth or a commercially available lens cleaning set.

SERVICE

This camera is a precision instruments and if treated with care, will provide years of satisfactory performance. However, in the event of a problem, the owner is advised not to attempt to make repairs or open the cabinet. Servicing should always be referred to your dealer or Sanyo Authorized Service Centre.

SPECIFICATIONS

Scaning system : PAL colour TV system

Interlace : PLL 2:1 interlace

Image device : 1/3 inch solid state image device CCD

Picture elements : 537 (H) x 597 (V): VCC-3700P, 795 (H) x 596 (V): VCC-3770P

Effective picture elements : 500 (H) x 582 (V): VCC-3700P, 752 (H) x 582 (V): VCC-3770P

Synchronizing system : Internal sync/Line lock manually switchable/External sync

Resolution : 330 TV lines horizontally, 400 TV lines vertically: VCC-3700P

English 13

(625 TV lines, 50 fields/sec.)

460 TV lines horizontally, 400 TV lines vertically: VCC-3770P

Page 15

SPECIFICATIONS

Video output level : 1.0 Vp-p/75 ohms, composite Y/C signal outputs : Y: Video; 0.7 Vp-p + sync; 0.3 Vp-p/75 ohms

Video S/N ratio : More than 46 dB

Minimum required illumination

(incandescent lighting)

Backlight compensation : Manual ON/OFF switching, Multi zone light measuring

Electronic iris function : Manual ON/OFF switching

Electronic shutter : 8 speeds, selectable by switches:

Flange-back : 12.5 mm ± 0.5 mm

White balance : Automatic (TTL system)/Manual

Gain control : Manual ON/OFF switching

Gamma correction : γ = 0.45

Lens mount : CS mount (or C mount with the supplied adaptor)

Environmental conditions : Temperature: –10˚C ~ +50˚C

Power supply : 220 – 230 V AC ± 10 %, 50 Hz

Power consumption : Approx. 4 W (VCC-3700P), 4.6 W (VCC-3770P)

Weight : Approx. 620 g (without lens)

Dimensions (W x H x D): 67 x 54 x 128 mm (without camera mount)

C: Burst; 0.3 Vp-p/75 ohms: VCC-3770P only

: Approx. 1.4 lux with a F 1.2 lens,

approx. 1.9 lux with a F 1.4 lens: VCC-3700P Approx. 2 lux with a F 1.2 lens, approx. 2.7 lux with a F 1.4 lens: VCC-3770P

system (Active when using an auto-iris lens)

(1/50, 1/120, 1/250, 1/500, 1/1000, 1/2000, 1/4000, 1/10000 sec.)

Humidity: less than 90% (no condensation)

VIDEO OUT VBS IN

POWER

(VCC-3770P)

Y/C OUT

LINE PHASE

1.3

136 128

1/4”–20 UNC

VIDEO OUT VBS IN

POWER

(VCC-3700P)

LINE PHASE

Features and specifications are subject to change without prior notice or obligations.

14 English