Sanyo VPC-J4, VPC-J4EX, VPC-J4EXBK, VPC-J4EXOR, VAR-G7U Service Manual

...

Download

Page 1

SERVICE MANUAL

FILE NO.

Digital Camera

VPC-J4

(Product Code : 126 670 01) (U.S.A., Canada, Korea, Taiwan)

AC adaptor

VPC-J4EX

(Product Code : 126 670 02) (Europe, PAL General)

VPC-J4EXBK

(Product Code : 126 670 05) (Europe, PAL General)

VPC-J4EXOR

(Product Code : 126 670 06)

Contents

1. OUTLINE OF CIRCUIT DESCRIPTION .................... 2

2. DISASSEMBLY .......................................................... 9

3. ELECTRICAL ADJUSTMENT .................................. 12

4. USB STORAGE INFORMATION

REGISTRATION ...................................................... 17

5. TROUBLESHOOTING GUIDE................................. 18

6. PARTS LIST............................................................. 19

Parts list of optional AC adaptor .............................. 19

Parts list of digital camera ........................................ 19

ACCESSORIES ....................................................... 19

PACKING MATERIALS............................................ 19

CABINET & CHASSIS PARTS 1 ............................. 20

CABINET & CHASSIS PARTS 2 ............................. 22

ELECTRICAL PARTS .............................................. 24

CIRCUIT DIAGRAMS &

PRINTED WIRING BOARDS ...................................... C1

PRODUCT SAFETY NOTICE

The components designated by a symbol ( ! ) in this schematic diagram designates components whose value are of

special significance to product safety. Should any component designated by a symbol need to be replaced, use only the part

designated in the Parts List. Do not deviate from the resistance, wattage, and voltage ratings shown.

(Europe, PAL General)

VAR-G7U

(Product Code : 126 301 15) (U.S.A., Canada)

VAR-G7EX

(Product Code : 126 301 16) (Europe, PAL General)

VAR-G7E

(Product Code : 126 301 17) (U.K.)

VAR-G7C

(Product Code : 126 301 18) (China)

CAUTION : Danger of explosion if battery is incorrectly replaced.

Replace only with the same or equivalent type recommended by the manufacturer. Discard used batteries according to the manufacturer’s instructions.

NOTE : 1. Parts order must contain model number, part number, and description.

2. Substitute parts may be supplied as the service parts.

3. N. S. P. : Not available as service parts.

Design and specification are subject to change without notice.

SX717/U, EX, EX2, EX3, SVA04/U, EX, E, C

REFERENCE No. SM5310567

Page 2

1. OUTLINE OF CIRCUIT DESCRIPTION

1-1. CA1 CIRCUIT DESCRIPTION

1. IC Configuration

IC901 (ICX488EQF) CCD imager IC905 (H driver, CDS, AGC and A/D converter)

Ø1

ØST

ØHLD

GND

Ø3B

Ø2

Ø4

Ø3A

Ø5AVØ5B

Ø6

2. IC901 (CCD imager)

[Structure]

Interline type CCD image sensor

Image size Diagonal 6.67 mm (1/2.7 type) Pixels in total 2396 (H) x 1766 (V) Recording pixels 2288 (H) x 1712 (V)

Pin No.

Symbol

Vø

Vø5B

Vø5A

Vø4

Vø3B

Vø3A

Vø2

Vø1

VøST

VøHLD

GND

Vertical register transfer clock

Horizontal addition control clock

GND

Pin Description

Pin No.

Horizontal register

SUB

GND

(Note) : Photo sensor

OUT

Vertical register

1615

Ø2B

Ø1B

1413

Fig. 1-1. CCD Block Diagram

Symbol

OUT

VDD

øRG

Hø

Hø2B

GND

øSUB

SUB

Hø

Hø2A

GND

Signal output

Circuit power

Reset gate clock

Horizontal register transfer clock

GND

Substrate clock

Substrate bias Horizontal register transfer clock

Horizontal register transfer clock

GND

Protection transistor bias

Pin Description

(Note)

Ø1A

Ø2A

GND

3. IC902, IC903 (V Driver) and IC905 (H driver)

An H driver and V driver are necessary in order to generate the clocks (vertical transfer clock, horizontal transfer clock and electronic shutter clock) which driver the CCD. IC902 and IC903 are V driver. In addition the XV1-XV6 signals which are output from IC101 are the vertical transfer clocks, and the XSG signal is superimposed at IC902 and IC903 in order to generate a ternary pulse. In addition, the XSUB signal which is output from IC101 is used as the sweep pulse for the electronic shutter. A H driver is inside IC905, and H1, H2 and RG clock are generated at IC905.

4. IC905 (CDS, AGC Circuit and A/D Converter)

The video signal which is output from the CCD is input to Pin (27) of IC905. There are inside the sampling hold block, AGC block and A/D converter block. The setting of sampling phase and AGC amplifier is carried out by serial data at Pin (32). The video signal is carried out A/D converter, and is output by 12-bit.

Table 1-1. CCD Pin Description

CCDIN

H1-H4

– 2 –

VRB

VRT

VREF

2~36 dB

VGA

PxGA

CDS

HORIZONTAL

DRIVERS

CLAMP

INTERNAL

CLOCKS

PRECISION

TIMING

CORE

SYNC

GENERATOR

Fig. 1-2. IC905 Block Diagram

ADC

CLAMP

INTERNAL

REGISTERS

SCK

SDATA

DOUT

CLI

Page 3

1-2. CP1 CIRCUIT DESCRIPTION

1. Circuit Description 1-1. Digital clamp

The optical black section of the CCD extracts averaged values from the subsequent data to make the black level of the CCD output data uniform for each line. The optical black section of the CCD averaged value for each line is taken as the sum of the value for the previous line multiplied by the coefficient k and the value for the current line multiplied by the coefficient 1-k.

1-2. Signal processor

1. γ correction circuit

This circuit performs (gamma) correction in order to maintain a linear relationship between the light input to the camera and the light output from the picture screen.

2. Color generation circuit

This circuit converts the CCD data into RGB signals.

3. Matrix circuit

This circuit generates the Y signals, R-Y signals and B-Y signals from the RGB signals.

4. Horizontal and vertical aperture circuit

This circuit is used gemerate the aperture signal.

1-3. AE/AWB and AF computing circuit

The AE/AWB carries out computation based on a 64-segment screen, and the AF carries out computations based on a 6segment screen.

1-4. SDRAM controller

This circuit outputs address, RAS, CAS and AS data for controlling the SDRAM. It also refreshes the SDRAM.

1-5. Communication control

1. SIO

This is the interface for the 8-bit microprocessor.

2. PIO/PWM/SIO for LCD

8-bit parallel input and output makes it possible to switch between individual input/output and PWM input/output.

1-6. TG/SG

Timing generated for 4 million pixel horizontal addtion CCD control.

1-7. Digital encorder

It generates chroma signal from color difference signal.

2. Outline of Operation

When the shutter opens, the reset signals (ASIC and CPU) and the serial signals (“take a picture” commands) from the 8-bit microprocessor are input and operation starts.

When the TG/SG drives the CCD, picture data passes through the A/D and CDS, and is then input to the ASIC as 12-bit data. The AF, AE, AWB, shutter, and AGC value are computed from this data, and three exposures are made to obtain the optimum picture. The data which has already been stored in the SDRAM is read by the CPU and color generation is carried out. Each pixel is interpolated from the surrounding data as being either Ye, Cy, Mg or B primary color data to produce R, G and B data. At this time, correction of the lens distortion which is a characteristic of wide-angle lenses is carried out. After AWB and γ processing are carried out, a matrix is generated and aperture correction is carried out for the Y signal, and the data is then compressed by JPEG and is then written to card memory (SD card). When the data is to be output to an external device, it is taken data from the memory and output via the USB I/F. When played back on the LCD and monitor, data is transferred from memery to the SDRAM, and the image is then elongated so that it is displayed over the SDRAM display area.

3. LCD Block

LCD block is in the CP1 board, and it is constructed by VCOM gerenated circuit etc. The video signal from the ASIC are input to LCD panel directly by 6-bit digital signal, and are converted into RGB signals by driver circuit in the LCD panel. Because the LCD closes more as the difference in potential between the VCOM (common polar voltage: AC) and the R, G and B signals becomes greater, the display becomes darker; if the difference inpotential is smaller, the element opens and the LCD becomes brighter. And also timing pulse except video signal are input at LCD panel directly from ASIC.

4. Lens drive block

4-1. Iris drive

When the drive signals (AMIN_A and AMIN_-A) which are output from the ASIC (IC101), it is driven by the driver (IC951), and are then used to drive the iris steps.

4-2. Focus drive

When the drive signals (FIN_A, FIN_-A, FIN_B and FIN_-B) which are output from the ASIC expansion I/O port (IC106), the focus stepping motor is driven by the driver (IC951). Detection of the standard focusing positions is carried out by means of the photointerruptor (FOCUS PI) inside the lens block.

4-3. Zoom drive

When the drive signals (ZIN_A, ZIN_-A, ZIN_B and ZIN_-B) which are output from the ASIC (IC101), the zoom stepping motor is driven by the driver (IC951). Detection of the standard zoom positions is carried out by means of photointerruptor (ZOOM PI) inside the lens block.

4-4. Shutter drive

When the drive signals (SMIN_A and SMIN_-A) which are output from the ASIC (IC101), it is driven regular current by the driver (IC951).

– 3 –

Page 4

1-3. ST1 POWER CIRCUIT DESCRIPTION

1. Outline

This is the main power circuit, and is comprised of the following blocks. Switching power controller (IC501) Analog system power output (Q5001, T5001) Digital 1.8 V power output (L5006) Digital 3.3 V power output (L5005) LCD 15 V power output (Q5015, L5007) LED backlight power output (Q5003, L5009) 5 V system power output (L5004)

4.7 V lens system power output (IC955, Q9552, L9551)

2. Switching Controller

This is the basic circuit which is necessary for controlling the power supply for a PWM-type switching regulator, and is provided with five built-in channels, only CH1 (analog system power output), CH2 (LCD 15 V power output), CH_M (digital

3.3 V system power output), CH_SD (digital 1.8 V system power output), CH3 (LED back light power output) and CH_SU (5 V system power output) are used. Feedback from 15.0 V (A) (CH1), 15 V (L) (CH2), 3.3 V (D) (CH_M), 1.8 V (D) (CH_SD), LED backlight output (CH3) and 5 V (CH_SU) power supply outputs are received, and the PWM duty is varied so that each one is maintained at the correct voltage setting level.

2-1. Short-circuit Protection

If output is short-circuited for the length of time setting inside IC501, all output is turned off. The control signal (P ON) are recontrolled to restore output.

3. Analog System Power Output

15.0 V (A), -7.6 V (A) and 3.45 V (A) are output. Feedback for the 15.0 V (A) is provided to the switching controller (Pin (3) of IC501) so that PWM control can be carried out.

4. Digital 1.8 V Power Output

1.8 V (D) is output. Feedback for the 1.8 V (D) is provided to the switching controller (Pins (9) of IC501) so that PWM control can be carried out.

5. Digital 3.3 V Power Output

3.3 V (D) is output. Feedback for the 3.3 V (D) is provided to the swiching controller (Pin (13) of IC501) so that PWM control can be carried out.

6. LCD 15 V Power Output

LCD 15 V (L) is output. Feedback for the 15 V (L) is provided to the swiching controller (Pin (31) of IC501) so that PWM control can be carried out.

7. LED Backlight Power Output

A constant current flows to LCD 8.5 V (L) power and the backlight LEDs. Feedback for the voltage of R5047 and R5048 are provided to the power controller (Pin (39) of IC501) so that PWM control can be carried out.

8. 5 V System Power Output

5 V is output. Feedback for the 5 V is provided to the swiching controller (Pin (17) of IC501) so that PWM control can be carried out.

9. 4.7 V Lens System Power Output

Lens power (4.7 V) is output. Feedback for the BOOST 4.7 V is provided to the swiching controller (Pin (1) of IC955) so that PWM control can be carried out.

– 4 –

Page 5

1-4. ST1 STROBE CIRCUIT DESCRIPTION

1. Charging Circuit

When UNREG power is supplied to the charge circuit and the CHG signal from microprocessor becomes High (3.3 V), the charging circuit starts operating and the main electorolytic capacitor is charged with high-voltage direct current. However, when the CHG signal is Low (0 V), the charging circuit does not operate.

1-1. Charge switch

When the CHG signal switches to Hi, IC541 starts charging operation.

1-2. Power supply filter

C5401 constitutes the power supply filter. They smooth out ripples in the current which accompany the switching of the oscillation transformer.

1-3. Oscillation circuit

This circuit generates an AC voltage (pulse) in order to increase the UNREG power supply voltage when drops in current occur. This circuit generates a drive pulse with a frequency of approximately 150-250 kHz. Because self-excited light omission is used, the oscillation frequency changes according to the drive conditions.

2. Light Emission Circuit

When FLCLT signal is input from the ASIC expansion port, the stroboscope emits light.

2-1. Emission control circuit

When the FLCLT signal is input to the emission control circuit, Q5409 switches on and preparation is made to the light emitting. Moreover, when a FLCLT signal becomes Lo, the stroboscope stops emitting light.

2-2. Trigger circuit

The Q5409 is turned ON by the FLCLT signal and light emission preparation is preformed. Simultaneously, high voltage pulses of several kV are emitted from the trigger coil and applied to the light emitter.

2-3. Light emitting element

When the high-voltage pulse form the trigger circuit is applied to the light emitting part, currnet flows to the light emitting element and light is emitted.

Beware of electric shocks.

1-4. Oscillation transformer

The low-voltage alternating current which is generated by the oscillation control circuit is converted to a high-voltage alternating current by the oscillation transformer.

1-5. Rectifier circuit

The high-voltage alternating current which is generated at the secondary side of T5401 is rectified to produce a highvoltage direct current and is accumulated at electrolytic capacitor C5412.

1-6. Voltage monitoring circuit

The functions programmed in the IC541 monitor oscillations and estimate the charging voltage. If the voltage exceeds the rated value, charging automatically stops. Then, the CHGDONE signal is changed to Lo output and a "charging stopped" signal is sent to the microcomputer.

– 5 –

Page 6

1-5. SYA CIRCUIT DESCRIPTION

1. Configuration and Functions

For the overall configuration of the SYA block, refer to the block diagram. The SYA block centers around a 8-bit microprocessor (IC301), and controls camera system condition (mode). The 8-bit microprocessor handles the following functions.

1. Operation key input, 2. Clock control and backup, 3. Power ON/OFF, 4. Storobe charge control, 5. Signal input and output for zoom and lens control.

21 LCD ON2

22 LCD ON

23 BLON

25 PRG SO

42~44

Signal

AVREF

AVSS

VDD

REGC

VSS

XIN

XOUT

RESET

XCIN

XCOUT

CLKSEL0

BAT_OFF

USB_DET

BR_OPEN

SREQ

BACKUP_CTL

LCD ON3

FLMD1

PRG SI

PRG SCK

MAIN RESET

VF. LED (R)

VF. LED (G)

VSS

VDD

P ON

PA O N

SCK

CHG ON

FLMD0

SCAN OUT 2~0

I/O

Outline

Analog standard voltage input terminal

GND

Power for program writing

VDD

Regulator output stability capacity connection

GND

Main clock oscillation terminal (4MHz)

Main clock oscillation terminal

Reset input

Clock oscillation terminal (32.768 kHz)

Clock oscillation terminal

ARM system clock ON/OFF

Battery off detection signal input

(Output mode “0” fixing) USB power detection terminal ( ↓ detection) Manual barrrier detection ( ↓ detection)

Communication transmission clock (SY-ASIC)

Backup battery charge control (L= charge)

D/D converter (LCD system) ON/OFF signal 3

Flash writing control 1

D/D converter (LCD system) ON/OFF signal 2

D/D converter (LCD system) ON/OFF signal 1

LCD backlight ON signal (H= lighting)

(Output mode “0” fixing)

Serial data output for flash

Serial data input for flash

Serial clock output for flash

System reset (MRST)

(Output mode “0” fixing)

VF LED (red) (L= lighting)

VF LED (green) (L= lighting)

GND

VDD

D/D converter (digital system) ON/OFF signal

D/D converter (analog system) ON/OFF signal

Serial clock output

Serial data input

Serial data output

Strobe charge control

Flash writing contol 0

(Output mode “0” fixing)

Key matrix output

See next page

– 6 –

Page 7

51~56

57 58

BOOT_COMREQ O

NC O

CARD

AVREF ON

PLLEN

ASIC TEST

SCAN IN5~0

DC_IN

AV_JACK

CHG_DONE I

INT_TEMP

BATTERY

Table 5-1. 8-bit Microprocessor Port Specification

Boot/command request (Output mode “0” fixing)

I Card detection (L= card)

I I

AD VREF ON/OFF signal (L= ON)

ASIC PLL oscillation ON/OFF

ASIC control signal (ZTEST)

Key scan input 5~0

DC adaptor connection detecion (L= DC adaptor)

AV JACK connection detection (H= AV JACK detection)

Storobe charge detection (input port) (L= ON)

Internal temperature detection (analog)

Battery voltage detection (analog)

2. Internal Communication Bus

The SYA block carries out overall control of camera operation by detecting the input from the keyboard and the condition of the camera circuits. The 8-bit microprocessor reads the signals from each sensor element as input data and outputs this data to the camera circuits (ASIC) or to the LCD display device as operation mode setting data. Fig. 5-1 shows the internal communication between the 8-bit microprocessor, ASIC and SPARC lite circuits.

ZTEST

ASIC RESET

S. REQ

8-bit

Microprocessor

Fig. 5-1 Internal Bus Communication System

ASIC SO

ASIC SI

ASIC SCK

PLLEN

CLKSEL0

3. Key Operaiton

For details of the key operation, refer to the instruction manual.

SCAN OUT

SCAN IN

← LEFT

MODE

REC (MOV)

↑ UP

REC (CAM)

↓ DOWN

TELE

PLAY

→ RIGHT

WIDE

SET

1st SHUTTER

ASIC

TEST

2nd SHUTTER

Table 5-2. Key Operation

– 7 –

Page 8

4. Power Supply Control

The 8-bit microprocessor controls the power supply for the overall system. The following is a description of how the power supply is turned on and off. When the battery is attached, a regulated 3.2 V voltage is normally input to the 8-bit microprocessor (IC301) by IC302, so that clock counting and key scanning is carried out even when the power switch is turned off, so that the camera can start up again. When the battery is removed, the 8-bit microprocessor operates in sleep mode using the backup lithium secondary battery. At this time, the 8-bit microprocessor only carries out clock counting, and waits in standby for the battery to be attached again. When a switch is operated, the 8-bit microprocessor supplies power to the system as required. The 8-bit microprocessor first sets both the P (A) ON signal at pin (35) and the P ON signal at pin (34) to high, and then turns on the DC/DC converter. After this, high signals are output from pins (12), (28), (49) and (50) so that the ASIC is set to the active condition. If the LCD monitor is on, the LCD ON signal at pin (22) and the LCD ON 2 signal at pin (21) set to high, and the DC/DC converter for the LCD monitor is turned on. Once it is completed, the ASIC returns to the reset condition, all DC/DC converters are turned off and the power supply to the whole system is halted.

ASIC,

memory

Power voltage

Power OFF

Power switch ON-

Auto power OFF

Shutter switch ON

CAMERA

Monitor OFF

LCD finder

Play back

Table 5-3. Camera Mode (Battery Operation)

Note) 4 MHz = Main clock operation, 32 kHz = Sub clock operation

3.3 V

OFF

CCD

5 V (A)

+15 V (A) etc.

OFF

ON→OFF

OFF

3.2 V

(ALWAYS)

32KHz OFF

4 MHz OFF

4 MHz ON

5. 16-bit A/D circuit (Audio)

This circuit converts the audio signals (analog signals) from the microphone to 16-bit digital signals.

8 bit

CPU

LCD

MONITOR

+15 V (L)

6. 16-bit D/A circuit (Audio)

The audio signals which were converted to digial form by the 16-bit A/D circuit are temporarily to a sound buffer and then recorded in the SSFDC card. During playback, the 16-bit D/A circuit converts these signals into analog audio signals.

– 8 –

Page 9

2. DISASSEMBLY

2-1. REMOVAL OF CABINET FRONT, TB2 BOARD AND CABINET BACK

1. Two screws 1.7 x 3

2. Three screws 1.7 x 2.5

3. Two screws 1.7 x 4

4. Cabinet front

5. Connector

6. Screw 1.7 x 2.5

7. TB2 board

8. Screw 1.7 x 3.5

9. Cabinet back

NOTE: Discharge a strobe capacitor

with the discharge jig (VJ8-0188) for

electric shock prevention.

2-2. REMOVAL OF LENS ASSEMBLY

1. Screw 1.7 x 3.5

2. Spacer speaker

3. Holder speaker

4. Connector

5. Speaker

6. Spacer wire ST1

7. Two screws 1.7 x 4.5

8. Screw 1.7 x 3.5

9. Holder lens

10. Screw 1.7 x 3.5

11. FPC

12. Connector

13. Lens assembly

14. Spacer lens FPC

15. Holder condenser

16. Remove the solder.

– 9 –

Page 10

2-3. REMOVAL OF LCD AND TB1 BOARD

1. FPC

2. Spacer EL FPC

3. Connector

4. LCD

5. Two screws 1.7 x 2.5

6. Screw 1.7 x 3.5

7. Holder DC USB

8. FPC

9. Remove the solder.

10. TB1 board

11. Holder button shutter

12. FPC

13. Two screws 1.7 x 2.5

14. Spacer FPC monitor

15. Screw 1.7 x 3.5

16. Holder back button

– 10 –

Page 11

2-4. REMOVAL OF CP1 BOARD AND ST1 BOARD

1. Screw 1.7 x 3.5

2. Holder mic

3. Screw 1.7 x 3.5

4. Connector

5. CP1 board

6. Screw 1.7 x 4.5

7. Remove the solder.

8. Holder flash

9. Screw 1.7 x 4.5

10. Remove the solder.

11. Terminal battery B

12. Terminal battery A

13. ST1 board

14. Holder battery

2-5. BOARD LOCATION

CA1 board

CP1 board

ST2 board

ST1 board

TB2 board

TB1 board

– 11 –

Page 12

3. ELECTRICAL ADJUSTMENT

Firmware

Image

AWB

Focus

UV Matrix

R Bright

RGB Offset

Tint

B Bright

Gain

Phase

LCD

Calibration

Upload

Initialize

LCD Type

H AFC Test

VCOMDC

VCOMPP

Cal Data

Cal Mode

EVF

USB storage

Get Set

VID

Set

PID

Set

Serial

Set

Rev.

Set

Setting

Language

Video Mode

VCO

Factory Code

3-1. Table for Servicing Tools

1Chroma meter

Part code

VJ8-0190

VJ8-0237

VJ8-0192

VJ8-0191

VJ8-0188

Ref. No.

J-1

J-2

J-3

Name

Pattern box (color viewer)

Siemens star chart

Calibration software

Number

J-4

J-5

J-6

Spare lump

Discharge jig

Note: J-1 Pattern box (color viewer) is 100 - 110 VAC only.

J-1 J-2

J-3

J-4

6. LCD Panel Adjustment 6-1. LCD VcomPP Adjustment 6-2. LCD VcomDC Adjustment Note: If the lens, CCD and board in item 2-5, it is necessary

to adjust again. Item 2-4 adjustments should be carried out in sequence. Item 5 adjustment should be carried out after item 3.

3-4. Setup

1. System requirements

Windows 98 or Me or 2000 or XP IBM R -compatible PC with pentium processor CD-ROM drive

3.5-inch high-density diskette drive USB port 40 MB RAM Hard disk drive with at least 15 MB available VGA or SVGA monitor with at least 256-color display

2. Installing calibration software

1. Insert the calibration software installation diskette into your diskette drive.

2. Open the explorer.

3. Copy the DscCalDI_140 folder on the floppy disk in the FD drive to a folder on the hard disk.

J-5

J-6

3-2. Equipment

1. Oscilloscope

2. Digital voltmeter

3. AC adaptor

4. PC (IBM R -compatible PC, Pentium processor, Window 98 or Me or 2000 or XP)

3-3. Adjustment Items and Order

1. IC501 Oscillation Frequency Adjustment

2. Lens Adjustment

3. AWB Adjustment

4. CCD White Point Defect Detect Adjustment

5. CCD Black Point And White Point Defect Detect Adjust-

ment In Lighted

3. Installing USB driver

Install the USB driver with camera or connection kit for PC.

4. Pattern box (color viewer)

Turn on the switch and wait for 30 minutes for aging to take place before using Color Pure. It is used after adjusting the chroma meter (VJ8-0192) adjust color temperature to 3100 ± 20 K and luminosity to 900 ± 20 cd/m

. Be careful of handling the lump and its circumference are high temperature during use and after power off for a while.

5. Computer screen during adjustment

– 12 –

Page 13

3-5. Connecting the camera to the computer

1. Line up the arrow on the cable connector with the notch on the camera's USB port. Insert the connector.

2. Locate a USB port on your computer.

To USB port

AC adaptor

USB cable

– 13 –

Page 14

3-6. Adjust Specifications

[ST1 board (Side A)]

CL518

2. Lens Adjustment

VR501

Backlight lead wire

TB1 board

power lead wire

ST1 board

CN501

CP1 board

CP1-ST1 connector

Note:

1. Frequency adjustment is necessary to repair in the ST1 board and replace the parts. It is carried out with play mode.

Preparation:

1. Discharge a strobe capacitor in the ST1 board.

2. Connect the connector in the CP1 board and CN501 in the ST1 board. Connect backlight lead wire to CN172 in the CP1 board. (Refer to above picture.)

3. Set the main switch to playback mode in the CP1 board.

4. Input DC power from TB1 board.

5. Carry out assembling the camera after adjusting the oscillation frequency .

1. IC501 Oscillation Frequency Adjustment

Measuring Point

Measuring Equipment

ADJ. Location

ADJ. Value

CL518

Frequency counter

VR501

496.5 ± 1 kHz

Camera

Approx.

150 cm 3 cm

Siemens

star chart

Preparation:

POWER switch: ON

Adjustment condition:

More than A3 size siemens star chart Fluorescent light illumination with no flicker Illumination above the subject should be 400 lux ± 10 %.

Adjustment method:

1. Set the siemens star chart 150 cm ± 3 cm so that it be-

comes center of the screen.

2. Connect the camera and the computer with USB cable.

3. Select “CARD READER”, and push the SET button.

4. Double-click on the DscCalDi.exe.

5. Click the Focus, and click the Yes.

6. Lens adjustment value will appear on the screen.

7. Click the OK.

DscCalDi

Focus Result

STD_AFPOS=1033 FOCUS=3,-36,0,0

Adjustment value determination is effectuated using the "STD

AFPOS" and "FOCUS" values.

If FOCUS=focus1, focus2 and the adjustment values fulfill the

conditions below, they are determined as within specifications.

Adjustment value determination

985<=STD_AFPOS<=1055

-20<=focus1<=+15

-80<focus2<0

Adjustment method:

1. Adjust with VR501 to 496.5 ± 1 kHz.

– 14 –

Page 15

3. AWB Adjustment

Camera

Pattern box

(color viewer)

Preparation:

POWER switch: ON

Adjusting method:

1. When setting the camera in place, set it to an angle so that nothing appears in any part of the color viewer except the white section. (Do not enter any light.)

2. Double-click on the DscCalDi.exe.

3. Click the AWB, and click the Yes.

4. AWB adjustment value will appear on the screen.

5. Click the OK.

Dsc Calibration

AWB Result: 1: AGC=190,357,524,692,860 3F_AGC=1,1 WB=318,513,716 CHECK=126,128,143 MS=3912,4296 0 IRIS=0

Copy

4. CCD White Point Defect Detect Adjustment

Preparation:

POWER switch: ON

Adjustment method:

1. Double-click on the DscCalDi.exe.

2. Select “CCD Defect” on the LCD “Test”, and click the “Ye s ”.

3. After the adjustment is completed, OK will display.

4. Click the OK.

5. CCD Black Point And White Point Defect Detect Adjustment In Lighted

Camera

Pattern box

(color viewer)

Preparation:

POWER switch: ON Setting of pattern box:

Color temperature: 3100 ± 20 (K) Luminance: 900 ± 20 (cd/m

Adjusting method:

1. Set the camera 0 cm from the pattern box. (Do not enter

any light.)

2. Double-click on the DscCalDi.exe.

3. Select “CCD Black” on the LCD “Test”, and click the “Ye s ”.

4. After the adjustment is completed, the number of defect

will appear.

)

Adjustment value determination is effectuated using the "AGC",

“CHECK" and "MS" values. If AGC=a1, a2, a3, a4, a5, CHECK=wc0, wc1, wc2 and MS=MS1, MS2, the adjustment values fulfill the conditions be-

low, they are determined as within specifications.

Adjustment value determination

a1<1023, a2<1023, a3<1023, a4<1023, a5<1023 wc0=128 ± 2, wc1=128 ± 2, wc2=130 ± 40 3400<=MS1<=4850 3800<=MS2<=5250

Adjustment values other than the above are irrelevant.

– 15 –

Page 16

6. LCD Panel Adjustment

[CP1 board (Side A)]

CL404

3-7. Factory Code Setting

1. Check the "Factory Code" display within the Setting group.

2. For models VPC-J4

If "FC_SANYO_U" does not appear, click on the " " mark located on the right of the "Factory Code" display BOX and select "FC_SANYO_U".

3. For models VPC-J4EX, VPC-J4EXBK or VPC-J4EXOR

If "FC_SANYO_EX" does not appear, click on the " " mark located on the right of the "Factory Code" display BOX and select "FC_SANYO_EX".

4. End "DscCal" and remove the camera before turning the

camera power OFF.

6-1. LCD VcomPP Adjustment

Preparation:

POWER switch: ON

Adjusting method:

1. Double-click on the DscCalDi.exe.

2. Adjust LCD “VCOMPP” so that the amplitude of the CL404

waveform is 5.60 V ± 0.05 Vp-p.

5.60 V ± 0.05 Vp-p

CL404 waveform

Calibration

AWB

Focus

UV Matrix

Cal Mode

Cal Data

USB storage

VID

Get

PID

Set

Upload

Firmware

Image

Initialize

EVF

LCD Type

LCD

R Bright

RGB Offset

Tint

VCO

H AFC Test

Serial

Set

Rev.

B Bright

Gain

Phase

Set Set

VCOMDC

VCOMPP

Setting

Language

Video Mode

Factory Code

6-2. LCD VcomDC Adjustment

Adjusting method:

1. Adjust LCD “VCOMDC” so that the amplitude of the CL404

waveform is 4.15 V ± 0.05 Vp-p.

CL404 waveform

4.15 V ± 0.05 Vp-p

GND

– 16 –

Page 17

4. USB STORAGE INFORMATION REGISTRATION

USB storage data is important for when the camera is connected to a computer via a USB connection. If there are any errors in the USB storage data, or if it has not been saved, the USB specification conditions will not be satisfied, so always check and save the USB storage data.

Preparation:

POWER switch: ON

Adjustment method:

1. Connect the camera to a computer. (Refer to 3-5. Connecting the camera to the computer on the page 13.)

2. Double-click on the DscCalDi.exe.

3. Click on the Get button in the USB storage window and check the USB storage data. VID: SANYO PID: J4 Serial: Rev. : 1.00

4. Check the “Serial” in the above USB storage data. If the displayed value is different from the serial number printed on the base of the camera, enter the number on the base of the camera. Then click the Set button.

5. Next, check VID, PID and Rev. entries in the USB storage data. If any of them are different from the values in 3. above, make the changes and then click the corresponding Set button.

Calibration

AWB

Focus

UV Matrix

Cal Mode

Cal Data

USB storage

VID

Get

PID

Set

Upload

Firmware

Image

Initialize

EVF

LCD Type

LCD

R Bright

RGB Offset

Tint

VCO

H AFC Test

Serial

Set

Rev.

B Bright

Gain

Phase

Set Set

VCOMDC

VCOMPP

Setting

Language

Video Mode

Factory Code

– 17 –

Page 18

5. TROUBLESHOOTING GUIDE

POWER LOSS INOPERTIVE

SET THE MAIN

SWITCH TO PLAY

MODE

IC301-56

(SCAN IN0)

PULSE INPUT

IC302-7 4.7 V

(BOOST 4.7 V)

YES

IC301-33

(VDD)

HIGH

IC301-9

(RESET)

HIGH

IC301-13

(BAT OFF)

HIGH

IC301-8

OSCILLATION

YES

IC301-11

OSCILLATION

YES

LOW

CHECK S3001

CHECK ST1, IC955,

CHECK IC302

CHECK IC302, RB302

CHECK RB302

CHECK X3001

CHECK X3002

Q9552

TAKING INOPERATIVE

PUSH SHUTTER

BUTTON

IC301-51, 52

(SCAN IN 4, 5)

PULSE INPUT

YES

CN301-34, 35

(P ON, P(A) ON)

HIGH

SERIAL

COMMUNICATION

CHECK CP1 DMA

BLOCK

THE UNIT SWITCH

LOW

CP1 DMA BLOCK

CHECK

IC301, ST1

CHECK IC301,

CHECK IC301

NO PICTURE

CLK (108 MHz)

INPUT TO

IC111-11 (CLK IN 1)

CLK (48 MHz)

INPUT TO

IC111-16 (CLK IN 2)

IC301-37, 38

(ASIC_SO, ASIC_SI)

CHECK CP1, CA1

MAIN CLOCK FOR SYSTEM OPERATION

NO OPERATION IF ABSENT CHECK X1101 OSCILLATOR AND IC111

CHECK IC111 etc.

INCORRECT HANDSHAKING

BETWEEN 8-BIT CPU AND ASIC CHECK EACH INTERFACE

– 18 –

Page 19

6. PARTS LIST

Parts list of optional AC adaptor : VAR-G7C/G7E/G7EX/G7U

LOCATION PARTS NO. DESCRIPTION LOCATION PARTS NO. DESCRIPTION

645 057 1510 CORD,POWER-1.9MK, VAR-G7U ONLY 645 002 6805 CORD,POWER-1.875MK,

VAR-G7EX ONLY 645 036 7434 CORD,POWER-1.2MK, VAR-G7E ONLY 645 065 3506 CORD,POWER-1.29MK, VAR-G7C ONLY

OR 645 068 1332 CORD,POWER-1.29MK, VAR-G7C ONLY

(VAR-G7C/U)

N.S.P.

Parts list of digital camera: VPC-J4/J4EX/J4EXBK/J4EXOR

ACCESSORIES

1 636 076 5344 STRAP-SX713/J 2 645 067 0497 DISC,CD-ROM SSP 717 U (N.S.P) 3 645 063 5816 BATTERY, RECHARGE, LI-ION 4 645 066 1877 BATTERY CHARGER 5 645 057 1503 CORD,POWER-1.2MK,EXCEPT VPC-J4 5 645 057 1510 CORD,POWER-1.9MK,VPC-J4 ONLY 6 645 065 4831 CABLE,DSC A/V SX713 7 645 065 4848 CABLE,DSC USB,SX791 8 645 058 8082 CARD,MEMORY 16MB OR 645 061 3357 CARD,MEMORY 16MB OR 645 065 9423 CARD,MEMORY 16MB 9112 636 077 6579 INSTRUCTION MANUAL

CAMERA (English)

(VAR-G7E)

(VAR-G7EX)

VAR-G7

Power cord

The AC adaptor VAR-G7C/E/EX/U consists of the adaptor (VAR-G7) and the AC power cord.

LOCATION PARTS NO. DESCRIPTION

N.S.P.

PACKING MATERIALS

7001 636 077 6234 CARTON CASE INNER-717/EX,

VPC-J4EX ONLY

7001 636 079 7833 CARTON CASE INNER-717/EX2,

VPC-J4EXBK ONLY

7001 636 079 7840 CARTON CASE INNER-717/EX3,

VPC-J4EXOR ONLY

7001 636 077 6241 CARTON CASE INNER-717/U,

VPC-J4 ONLY 7002 636 078 4659 CUSHION SHEET-SX792/KRNK 7003 636 077 2854 REINFORCEMENT PAD,A-713EX

BOTTOM 7004 636 077 6265 REINFORCEMENT PAD,B-713EX TOP

Page 20

CABINET & CHASSIS PARTS 1

103

106

105

102

104

105

103

101

SX717/J Parts List-1

102

N.S.P.: Not available as service parts.

Page 21

LOCATION PARTS NO. DESCRIPTION LOCATION PARTS NO. DESCRIPTION

1 636 077 7569 ASSY,COVER LENS-SX717/J,

VPC-J4,VPC-J4EX

1 636 079 5617 ASSY,COVER LENS-717/EX--3,

VPC-J4EXOR ONLY

1 636 079 3989 ASSY,COVER LENS-717/J---2,

VPC-J4EXBK ONLY

2 636 077 7576 ASSY,COVER FRONT-SX717/J,

VPC-J4,VPC-J4EX

2 636 079 5631 ASSY,COVER FRONT-717EX--3,

VPC-J4EXOR ONLY

2 636 079 3996 ASSY,COVER FRONT-717J- --2,

VPC-J4EXBK ONLY 3 636 078 6509 SPACER FPC MONITOR SX717 4 636 078 2518 SPACER COVER FRONT-SX717 5 636 080 2438 SPACER FLASH A-SX713/J 6 636 080 8102 ADHESIVE COVER FRONT-713J 7 636 053 9839 BALL CLICK SR951/JO 8 636 075 7837 DEC VF FRONT-SX713/J 9 636 075 7844 DEC MIRROR-SX713/J 10 636 076 4880 ADHESIVE DEC FRONT-SX713J 11 636 075 7721 CABINET FRONT INNER-713/J 12 636 080 4630 SPACER TB2 SX713/J 13 636 077 0805 COMPL PWB,TB-2 14 636 075 7189 SPRING COVER LENS-SX713/J 15 636 075 7967 HOLDER BARIA LEVER-SX713J 16 636 075 7875 HOLDER BUTTON SLIDE-713/J 17 636 075 7707 BUTTON SLIDE-SX713/J 18 636 075 7882 HOLDER COVER JACK-SX713/J 19 636 079 3941 ASSY,BUTTON MENU-717J---2,

VPC-J4EXBK ONLY 19 636 076 4712 ASSY,BUTTON OK-SX713/J,EXCEPT

VPC-J4EXBK 20 636 075 7806 DEC BUTTON MENU-SX713/J 21 636 075 7677 BUTTON ZOOM-SX713/J 22 636 075 7790 DEC LED BACK-SX713/J 23 636 076 0615 ADHESIVE COVER BACK-713/J 24 636 077 1086 SPACER DEC MONITOR-SX717/ 25 636 080 8263 SPACER LCD FPC-SX713/J 26 636 077 0898 ASSY,COVER BACK-SX717/J,

VPC-J4,VPC-J4EX 26 636 079 5655 ASSY,COVER BACK-717/EX--3,

VPC-J4EXOR ONLY 26 636 079 4009 ASSY,COVER BACK-717/J---2,

VPC-J4EXBK ONLY 27 636 077 7682 DEC CENTER LEFT-SX717/J,

EXCEPT VPC-J4EXBK 27 636 079 4238 DEC CENTER LEFT-717/J---2,

VPC-J4EXBK ONLY 28 411 000 9403 RING E 2 29 411 008 4905 WASHER F 3X6X0.5 30 636 075 6854 HOLDER STRAP A-SX713/J 31 636 075 6861 HOLDER STRAP B-SX713/J 32 636 080 2391 SPACER STRAP-SX713/J 33 636 080 9505 ADHESIVE DEC TOP C SX713 34 636 078 5953 ADHESIVE DEC TOP B SX713 35 636 080 5965 SPACER DEC TOP-SX713/J 36 636 080 1868 SHIELD TAPE CCD 37 636 080 5941 ADHESIVE DEC TOP A SX713 38 636 079 6218 COVER JACK-SX717/EX--3,

VPC-J4EXOR ONLY 38 636 079 3644 COVER JACK-SX717/J,VPC-J4,VPC-J4EX 38 636 079 4191 COVER JACK-SX717/J---2,

VPC-J4EXBK ONLY 39 636 077 1031 DEC MONITOR-SX717/J 40 636 077 1017 COVER VF-SX717/J 41 636 077 7675 DEC CENTER TOP-SX717/J,

EXCEPT VPC-J4EXBK 41 636 079 4221 DEC CENTER TOP-717/J---2,

VPC-J4EXBK ONLY 101 412 063 8501 SPECIAL SCREW-1.7X4.0,

VPC-J4EXBK ONLY 101 412 064 3505 SPECIAL SCREW-1.7X4.0,

EXCEPT VPC-J4EXBK 102 412 064 3604 SPECIAL SCREW-1.7X2.5,

EXCEPT VPC-J4EXBK 102 412 064 3703 SPECIAL SCREW-1.7X2.5,

VPC-J4EXBK ONLY

103 412 067 2406 SPECIAL SCREW 1.7X3W,

VPC-J4EXBK ONLY

103 412 063 6101 SPECIAL SCREW-1.7X3.0,

EXCEPT VPC-J4EXBK 104 411 176 6701 SCR S-TPG PAN PCS 1.7X2.5 105 411 180 2102 SCR S-TPG PAN PCS 1.7X3.5 106 411 169 6800 SCR PAN PCS 1.7X1.5

Page 22

CABINET & CHASSIS PARTS 2

41 40

105

108

107

105

108

107

105

SX717/J Parts List-2

17 18

104

105

N.S.P.: Not available as service parts.

Page 23

LOCATION PARTS NO. DESCRIPTION

1 636 080 4654 SPACER MIC-SX713/J 2 636 075 7943 HOLDER MIC-SX713/J 3 645 063 5571 MICROPHONE 4 636 077 0744 COMPL PWB CP-1 5 636 078 5977 SPACER FPC CP1-SX713/J 6 636 077 0775 COMPL PWB,ST-1 7 636 075 7196 TERMINAL BATTERY A-SX713J 8 636 075 7202 TERMINAL BATTERY B-SX713J 9 636 076 5115 COMPL,REFLECTOR SX713 10 636 080 2384 SPACER WIRE ST1-SX713/J 11 636 075 7172 SPRING LEVER EJECT-SX713J 12 636 075 7981 LEVER BATTERY EJECT-713/J 13 636 075 7912 HOLDER BATTERY F-SX713/J,

13 636 079 4283 HOLDER BATTERY F-SX717/J,

14 636 076 3739 STAND-SX713/J,EXCEPT VPC-J4EXBK 14 636 079 4429 STAND-SX717/J,VPC-J4EXBK ONLY 15 636 078 4574 SPACER EL FPC-SX713/J 16 636 075 7141 SPRING LEVER LOCK SX713/J 17 636 075 7165 SPRING COVER BATT-SX713/J 18 636 075 6939 HOLDER COVER BATT-SX713/J 19 636 079 6232 COVER BATTERY-SX717/EX--3,

19 636 077 1024 COVER BATTERY-SX717/J,VPC-J4,

19 636 079 4214 COVER BATTERY-SX717/J---2,

20 636 075 7127 SHAFT COVER BATT-SX713/J 21 636 076 9403 ADHESIVE SPEAKER-SX713 22 645 064 9950 SPEAKER,8 23 636 075 6946 HOLDER SPEAKER-SX713/J 24 636 079 3668 SPACER SPEAKER-SX713/J 25 636 078 6509 SPACER FPC MONITOR SX717 26 636 076 3159 LABEL COUTION BATT-SX713 27 636 075 7998 LEVER LOCK BATTERY-SX713J 28 636 077 1055 HOLDER MONITOR-SX717/J,

28 636 079 4290 HOLDER MONITOR-SX717/J,

29 636 078 7964 ADHESIVE MONITOR SX717/J 30 636 077 6647 ASSY,WIRE LCD-CP1-SX717 31 636 078 7995 ADHESIVE FPC MONIT-SX717J 32 645 067 0169 LCD(TM018QV-A02-01) 33 636 076 9465 SPACER FLASH-SX713/J 34 636 078 3614 SPACER MONITOR SIDE SX717 35 636 077 0799 COMPL PWB,TB-1 36 636 078 4581 SPACER TB1-SX713/J 37 636 076 5931 FLEXIBLE PWB,713 CP1-TB1 38 636 075 6953 HOLDER DC USB-SX713/J 39 636 075 6915 HOLDER BACK BUTTON-SX713J 40 636 078 0194 ADHESIVE SWITCH-SX713 41 645 066 9453 UNIT,SW FPC 42 636 075 7899 HOLDER BUTTON SHUTTER-713 43 636 064 4977 SPRING SHUTTER-SX541/JM 44 636 075 7714 BUTTON SHUTTER-SX713/J 45 636 075 6922 HOLDER LENS-SX713/J 46 636 078 0187 ADHESIVE HLD LENS-SX713 47 636 078 6608 COMPL PWB,CA-1 SV-SX717 48 636 077 0782 COMPL PWB,ST-2 49 636 075 7950 HOLDER CONDENSER-SX713/J 50 636 078 4598 SPACER LENS FPC SX713/J 51 636 080 7839 SPACER MIC BLACK-SX717/J,

104 411 176 6701 SCR S-TPG PAN PCS 1.7X2.5 105 411 180 2102 SCR S-TPG PAN PCS 1.7X3.5 107 411 178 9007 SCR PAN PCS 1.7X2.5 108 411 181 6901 SCR S-TPG PAN PCS 1.7X4.5

EXCEPT VPC-J4EXBK

VPC-J4EXBK ONLY

VPC-J4EXOR ONLY

VPC-J4EX

VPC-J4EXBK ONLY

EXCEPT VPC-J4EXBK

VPC-J4EXBK ONLY

Page 24

ELECTRICAL PARTS

Note:

1. Materials of Capacitors and Resistors are abbreviated as follows ; Resistors Capacitors MT-FILM Metallized Film Resistor MT-POLYEST Metallized Polyester Capacitor MT-GLAZE Metallized Glaze Resistor MT-COMPO Metallized Composite Capacitor OXIDE-MT Oxide Metallized Film Resistor TA-SOLID Tantalum Solid Capacitor

2. Tolerance of Capacitor (10pF over) and Resistor are noted with follow symboles.

F ............1% G ............2% J ............5% K ............10%

M ..........20% N ..........30% Z ..........+80% ~ -20%

3. Capacitors

FP : pF

U :

4. Inductors

H MH : mH

UH :

5. N.S.P. : Not available as service parts.

LOCATION PARTS NO. DESCRIPTION LOCATION PARTS NO. DESCRIPTION

COMPL PWB CP-1

636 077 0744

Q1001 405 115 6709 TR DTC123EE Q1002 405 115 6709 TR DTC123EE Q1003 405 115 6709 TR DTC123EE Q1305 405 167 0304 TR EMD3 Q1306 405 166 9506 TR EMH2 Q1432 405 167 0403 TR EMD12 Q1501 405 115 5108 TR 2SA1774 R Q1801 405 168 3809 TR DTA144EM Q1802 405 175 9801 TR DTC143TM Q3001 405 168 4004 TR DTA114EM OR 405 172 4809 TR UNR31A1 Q3002 405 168 3809 TR DTA144EM OR 405 172 4908 TR UNR31A3 Q3003 405 168 3700 TR DTC144EM OR 405 172 4700 TR UNR32A3 Q3004 405 115 6709 TR DTC123EE Q9510 405 092 2107 TR 2SC4097-R Q9511 405 166 9506 TR EMH2

IC101 409 592 9109 IC 67000717D (N.S.P.) BGA IC106 409 479 6009 IC TC7MH273FK IC107 409 479 6009 IC TC7MH273FK IC111 409 575 5906 IC BU2394KN-E2 IC152 409 559 5908 IC TK15460L IC172 409 446 9309 IC NJM2125F IC181 409 557 9007 IC BH6411KN IC182 409 505 9400 IC TK11130CS IC301 410 519 4503 IC UPD790017GB-020-8EU-A IC301 410 511 7205 IC 78F0134AM2GB-020-8EU-A IC302 409 581 9608 IC S-8424BAAFT-G IC302 409 530 6900 IC S-8424BAAFT IC951 409 512 9806 IC LB8649FN

D1001 407 210 1900 DIODE 1SS400 D1002 408 053 2604 LED SLC-F117AA-J-T1 D1701 407 221 4105 DIODE MA2SD19 D3001 407 227 3102 DIODE EMP11 D3002 407 227 3102 DIODE EMP11 D3003 407 227 3102 DIODE EMP11 D3004 407 222 4807 LED SML-521MUW D3007 407 205 2806 DIODE RB520S-30

X1101 645 053 8780 OSC,CRYSTAL 28.63636MHZ X3001 645 046 1415 OSC,CERAMIC 4.00MHZ X3002 645 054 3791 OSC,CRYSTAL 32.768KHZ

XF101 645 057 0551 FILTER,EMI 1000000PF XF111 645 057 0551 FILTER,EMI 1000000PF

(SEMICONDUCTORS)

(INTEGRATED CIRCUITS)

(DIODES)

(OSCILLARTORS)

(FILTERS)

AL-SOLID Aluminum Solid Capacitor NP-ELECT Non-Polarized Electrolytic Capacitor OS-SOLID Aluminum Solid Capacitors with Organic

Semiconductive Electrolytic Capacitor

DL-ELECT Double Layered Electrolytic Capacitor

(INDUCTORS)

L1001 645 020 1912 INDUCTOR,240 OHM L1040 645 061 7393 INDUCTOR,10U M L1051 645 061 7416 INDUCTOR,47U M L1101 645 020 1912 INDUCTOR,240 OHM L1103 645 020 1899 INDUCTOR,68 OHM L1501 645 035 7183 INDUCTOR,10U J L1701 645 061 7393 INDUCTOR,10U M L1702 645 061 7393 INDUCTOR,10U M L1705 645 061 7416 INDUCTOR,47U M L1901 645 041 1977 INDUCTOR,330 OHM

(VARISTORS)

VA131 408 050 0504 VARISTOR AVR-M1005C080MT OR 408 050 0504 VARISTOR AVR-M1005C080MT VA302 408 050 0504 VARISTOR AVR-M1005C080MT VA303 408 050 0504 VARISTOR AVR-M1005C080MT VA304 408 050 0504 VARISTOR AVR-M1005C080MT VA305 408 050 0504 VARISTOR AVR-M1005C080MT VA306 408 050 0504 VARISTOR AVR-M1005C080MT

(CAPACITORS)

C1026 403 382 3902 CERAMIC 0.1U K 6.3V C1028 403 382 3902 CERAMIC 0.1U K 6.3V C1030 403 382 3902 CERAMIC 0.1U K 6.3V C1034 403 382 3902 CERAMIC 0.1U K 6.3V C1039 403 382 3902 CERAMIC 0.1U K 6.3V C1040 403 346 2309 CERAMIC 0.1U K 10V C1042 403 382 3902 CERAMIC 0.1U K 6.3V C1044 403 382 3902 CERAMIC 0.1U K 6.3V C1048 403 382 3902 CERAMIC 0.1U K 6.3V C1051 403 346 2309 CERAMIC 0.1U K 10V C1052 403 369 0306 CERAMIC 1U Z 4V C1053 403 375 0307 CERAMIC 4.7U K 4V C1054 403 312 6805 CERAMIC 0.1U Z 16V C1055 403 346 2309 CERAMIC 0.1U K 10V C1056 403 346 2309 CERAMIC 0.1U K 10V C1063 403 382 3902 CERAMIC 0.1U K 6.3V C1067 403 382 3902 CERAMIC 0.1U K 6.3V C1068 403 283 6309 CERAMIC 1U Z 10V C1069 403 283 6309 CERAMIC 1U Z 10V C1072 403 375 0307 CERAMIC 4.7U K 4V C1101 403 382 3902 CERAMIC 0.1U K 6.3V C1102 403 309 8102 CERAMIC 5P C 50V C1104 403 382 3902 CERAMIC 0.1U K 6.3V C1105 403 309 8102 CERAMIC 5P C 50V C1106 403 309 8409 CERAMIC 10P D 50V C1501 403 311 3805 CERAMIC 12P J 50V C1504 403 346 2309 CERAMIC 0.1U K 10V C1512 403 345 3802 TA-SOLID 22U M 4V C1513 403 345 4205 TA-SOLID 47U M 6.3V C1515 403 332 9503 CERAMIC 1U M 6.3V C1701 403 332 9503 CERAMIC 1U M 6.3V C1702 403 332 9503 CERAMIC 1U M 6.3V C1704 403 332 9503 CERAMIC 1U M 6.3V

Page 25

LOCATION PARTS NO. DESCRIPTION LOCATION PARTS NO. DESCRIPTION

C1705 403 332 9503 CERAMIC 1U M 6.3V C1706 403 401 5801 CERAMIC 10U K 10V C1707 403 332 9503 CERAMIC 1U M 6.3V C1712 403 379 6701 CERAMIC 10U K 16V C1713 403 358 3202 CERAMIC 10U K 6.3V C1716 403 332 9503 CERAMIC 1U M 6.3V C1801 403 346 2309 CERAMIC 0.1U K 10V C1802 403 382 3902 CERAMIC 0.1U K 6.3V C1803 403 375 0307 CERAMIC 4.7U K 4V C1804 403 346 2309 CERAMIC 0.1U K 10V C1806 403 346 2309 CERAMIC 0.1U K 10V C1808 403 344 0505 CERAMIC 0.033U K 10V C1809 403 346 2309 CERAMIC 0.1U K 10V C1810 403 344 0505 CERAMIC 0.033U K 10V C1811 403 332 9503 CERAMIC 1U M 6.3V C1812 403 375 0307 CERAMIC 4.7U K 4V C1813 403 377 8905 CERAMIC 2.2U K 6.3V C1814 403 332 9503 CERAMIC 1U M 6.3V C1817 403 381 8106 CERAMIC 1U K 6.3V C1818 403 346 2309 CERAMIC 0.1U K 10V C1819 403 375 0307 CERAMIC 4.7U K 4V C1901 403 358 3202 CERAMIC 10U K 6.3V C1903 403 358 3202 CERAMIC 10U K 6.3V C1904 403 373 5908 CERAMIC 1000P K 16V C1905 403 373 5908 CERAMIC 1000P K 16V C3002 403 381 8106 CERAMIC 1U K 6.3V C3003 403 382 3902 CERAMIC 0.1U K 6.3V C3005 403 312 6805 CERAMIC 0.1U Z 16V C3006 403 312 6805 CERAMIC 0.1U Z 16V C3007 403 368 7702 TA-SOLID 15U M 6.3V C3008 403 381 8106 CERAMIC 1U K 6.3V C3011 403 381 8106 CERAMIC 1U K 6.3V C3013 403 382 3902 CERAMIC 0.1U K 6.3V C3014 403 317 2505 CERAMIC 20P J 50V C3015 403 317 2505 CERAMIC 20P J 50V C3016 403 381 8106 CERAMIC 1U K 6.3V C3021 403 346 2309 CERAMIC 0.1U K 10V C9501 403 344 0505 CERAMIC 0.033U K 10V C9502 403 344 0505 CERAMIC 0.033U K 10V C9503 403 344 0505 CERAMIC 0.033U K 10V C9504 403 344 0505 CERAMIC 0.033U K 10V C9505 403 312 6805 CERAMIC 0.1U Z 16V C9507 403 382 3902 CERAMIC 0.1U K 6.3V C9509 403 312 6805 CERAMIC 0.1U Z 16V C9510 403 312 6805 CERAMIC 0.1U Z 16V C9512 403 312 6805 CERAMIC 0.1U Z 16V C9515 403 344 0505 CERAMIC 0.033U K 10V C9517 403 344 0505 CERAMIC 0.033U K 10V C9518 403 344 0505 CERAMIC 0.033U K 10V CB181 403 392 5507 CERAMIC 1U K 6.3V

(RESISTOR PACKS)

RB101 645 037 4371 R-NETWORK 220X4 1/32W RB103 645 037 4371 R-NETWORK 220X4 1/32W RB104 645 037 4371 R-NETWORK 220X4 1/32W RB105 645 037 4371 R-NETWORK 220X4 1/32W RB106 645 028 0719 R-NETWORK 10KX4 1/32W RB107 645 037 4371 R-NETWORK 220X4 1/32W RB301 645 028 0719 R-NETWORK 10KX4 1/32W RB302 645 061 3678 R-NETWORK 100KX2 1/16W RB303 645 061 3722 R-NETWORK 47KX2 1/16W RB304 645 032 8886 R-NETWORK 47KX4 1/32W RB305 645 061 3678 R-NETWORK 100KX2 1/16W RB306 645 061 3661 R-NETWORK 10KX2 1/16W RB307 645 032 8886 R-NETWORK 47KX4 1/32W RB951 645 061 3661 R-NETWORK 10KX2 1/16W

(RESISTORS)

R1001 401 302 2004 MT-GLAZE 10K JA 1/20W R1004 401 225 7902 MT-GLAZE 220 JA 1/16W R1005 401 224 9105 MT-GLAZE 150 JA 1/16W R1006 401 224 8801 MT-GLAZE 100 JA 1/16W R1007 401 225 8008 MT-GLAZE 330 JA 1/16W R1010 401 224 9303 MT-GLAZE 1K JA 1/16W R1012 401 224 8801 MT-GLAZE 100 JA 1/16W R1018 401 226 1503 MT-GLAZE 0.000 ZA 1/16W R1031 401 225 1900 MT-GLAZE 68 JA 1/16W R1051 401 226 1503 MT-GLAZE 0.000 ZA 1/16W R1052 401 261 3401 MT-FILM 3.6K DU 1/16W

R1053 401 261 5108 MT-FILM 1.0K DU 1/16W R1054 401 225 8503 MT-GLAZE 1.8K JA 1/16W R1055 401 261 5108 MT-FILM 1.0K DU 1/16W R1056 401 261 6303 MT-FILM 180 DU 1/16W R1064 401 302 2004 MT-GLAZE 10K JA 1/20W R1065 401 307 1101 MT-GLAZE 47K JA 1/20W R1066 401 302 2103 MT-GLAZE 1K JA 1/20W R1069 401 307 1101 MT-GLAZE 47K JA 1/20W R1102 401 224 8801 MT-GLAZE 100 JA 1/16W R1103 401 225 1801 MT-GLAZE 47 JA 1/16W R1104 401 225 1801 MT-GLAZE 47 JA 1/16W R1105 401 226 1503 MT-GLAZE 0.000 ZA 1/16W R1111 401 261 5306 MT-FILM 470 DU 1/16W R1310 401 302 2004 MT-GLAZE 10K JA 1/20W R1311 401 225 3805 MT-GLAZE 1.5K JA 1/16W R1350 401 225 1108 MT-GLAZE 27 JA 1/16W R1359 401 225 1108 MT-GLAZE 27 JA 1/16W R1401 401 302 2004 MT-GLAZE 10K JA 1/20W R1501 401 224 9907 MT-GLAZE 22K JA 1/16W R1502 401 225 7902 MT-GLAZE 220 JA 1/16W R1512 401 225 3805 MT-GLAZE 1.5K JA 1/16W R1523 401 226 1503 MT-GLAZE 0.000 ZA 1/16W R1526 401 261 9700 MT-FILM 75 DD 1/16W R1701 401 225 1207 MT-GLAZE 4.7K JA 1/16W R1702 401 261 2602 MT-FILM 10K DU 1/16W R1703 401 261 8703 MT-FILM 22K DD 1/16W R1704 401 261 2602 MT-FILM 10K DU 1/16W R1705 401 224 9808 MT-GLAZE 220K JA 1/16W R1706 401 261 9106 MT-FILM 12K DD 1/16W R1707 401 261 8505 MT-FILM 47K DD 1/16W R1708 401 261 9106 MT-FILM 12K DD 1/16W R1709 401 261 3203 MT-FILM 3K DU 1/16W R1711 401 225 0507 MT-GLAZE 33K JA 1/16W R1713 401 261 4101 MT-FILM 2.7K DU 1/16W R1716 401 226 1503 MT-GLAZE 0.000 ZA 1/16W R1803 401 224 9501 MT-GLAZE 2.2K JA 1/16W R1805 401 225 1009 MT-GLAZE 2.2M JA 1/16W R1810 401 224 9501 MT-GLAZE 2.2K JA 1/16W R1818 401 224 9303 MT-GLAZE 1K JA 1/16W R1819 401 224 9105 MT-GLAZE 150 JA 1/16W R1905 401 302 2004 MT-GLAZE 10K JA 1/20W R3001 401 235 1402 MT-GALZE 1.2K JA 1/16W R3002 401 302 2103 MT-GLAZE 1K JA 1/20W R3003 401 307 1101 MT-GLAZE 47K JA 1/20W R3004 401 224 9303 MT-GLAZE 1K JA 1/16W R3008 401 258 7009 MT-GLAZE 150K DC 1/16W R3009 401 258 7009 MT-GLAZE 150K DC 1/16W R3013 401 225 0408 MT-GLAZE 330K JA 1/16W R3015 401 240 9509 MT-GLAZE 820 JA 1/16W R3027 401 225 7902 MT-GLAZE 220 JA 1/16W R3051 401 226 1503 MT-GLAZE 0.000 ZA 1/16W R9501 401 291 6908 MT-FILM 0.47 FA 1/4W R9503 401 261 8901 MT-FILM 27K DD 1/16W R9504 401 261 8901 MT-FILM 27K DD 1/16W R9506 401 261 3302 MT-FILM 3.3K DU 1/16W R9509 401 301 0308 MT-FILM 0.56 FA 1/4W R9515 401 224 8801 MT-GLAZE 100 JA 1/16W R9516 401 224 8801 MT-GLAZE 100 JA 1/16W R9517 401 224 9006 MT-GLAZE 10K JA 1/16W R9518 401 224 9006 MT-GLAZE 10K JA 1/16W R9519 401 225 1405 MT-GLAZE 47K JA 1/16W R9520 401 225 3805 MT-GLAZE 1.5K JA 1/16W

(SWITCHES)

S3001 645 064 9967 SWITCH,SLIDE 1P-3T S3002 645 045 2857 SWITCH,PUSH S3003 645 045 2857 SWITCH,PUSH S3004 645 045 2857 SWITCH,PUSH S3005 645 045 2857 SWITCH,PUSH S3006 645 045 2857 SWITCH,PUSH S3007 645 045 2857 SWITCH,PUSH S3008 645 045 2857 SWITCH,PUSH

(CONNECTORS)

CN101 645 064 9936 SOCKT,PWB-PWB 50P(N.S.P) CN102 645 064 9929 PLUG,PWB-PWB 50P (N.S.P) CN103 645 067 3962 SOCKET,FPC 11P (N.S.P) CN171 645 066 9613 SOCKET,FPC 33P (N.S.P) CN172 645 059 0122 PLUG,PWB-WIRE 2P (N.S.P)

Page 26

LOCATION PARTS NO. DESCRIPTION LOCATION PARTS NO. DESCRIPTION

CN181 645 059 0122 PLUG,PWB-WIRE 2P (N.S.P) CN301 645 059 0214 SOCKET,FPC 6P (N.S.P) CN951 645 055 5183 SOCKET,FPC 18P (N.S.P)

COMPL PWB,CA-1 SV-SX717

636 078 6608

(SEMICONDUCTORS)

Q9001 405 153 6709 TR 2SC3931-D (N.S.P) Q9002 405 102 5609 TR 2SD1819A-R (N.S.P) OR 405 092 4101 TR 2SC4081-R (N.S.P)

(INTEGRATED CIRCUITS)

IC902 409 543 2807 IC CXD3440EN-1 (N.S.P) IC903 409 543 2807 IC CXD3440EN-1 (N.S.P) IC905 409 594 7400 IC AD9949KCPZ (N.S.P) IC906 409 505 9400 IC TK11130CS (N.S.P)

(DIODES)

D9001 407 198 9905 DIODE MA727 (N.S.P) D9002 407 113 5609 DIODE DSH015 (N.S.P)

(FILTER)

XF901 645 057 0551 FILTER,EMI 1000000PF (N.S.P)

(INDUCTOR)

L9001 645 020 1912 INDUCTOR,240 OHM (N.S.P)

(CAPACITORS)

C9001 403 390 6407 CERAMIC 4.7U M 16V (N.S.P) C9003 403 192 5905 CERAMIC 0.1U K 25V (N.S.P) C9004 403 376 4304 CERAMIC 3.3U K 10V (N.S.P) C9005 403 320 5500 CERAMIC 1U Z 25V (N.S.P) C9006 403 164 0204 CERAMIC 0.1U Z 25V (N.S.P) C9007 403 346 2309 CERAMIC 0.1U K 10V (N.S.P) C9008 403 312 6805 CERAMIC 0.1U Z 16V (N.S.P) C9009 403 379 0808 CERAMIC 1U M 16V (N.S.P) C9010 403 192 5905 CERAMIC 0.1U K 25V (N.S.P) C9011 403 381 8106 CERAMIC 1U K 6.3V (N.S.P) C9013 403 379 0808 CERAMIC 1U M 16V (N.S.P) C9014 403 384 9209 CERAMIC 1U M 4V (N.S.P) C9015 403 381 8106 CERAMIC 1U K 6.3V (N.S.P) C9016 403 381 8106 CERAMIC 1U K 6.3V (N.S.P) C9017 403 381 8106 CERAMIC 1U K 6.3V (N.S.P) C9018 403 346 2309 CERAMIC 0.1U K 10V (N.S.P) C9020 403 320 5302 CERAMIC 0.15U K 25V (N.S.P) C9021 403 346 2309 CERAMIC 0.1U K 10V (N.S.P) C9022 403 346 2309 CERAMIC 0.1U K 10V (N.S.P) C9023 403 329 6508 TA-SOLID 10U M 6.3V (N.S.P) C9024 403 346 2309 CERAMIC 0.1U K 10V (N.S.P) C9025 403 329 6508 TA-SOLID 10U M 6.3V (N.S.P) C9026 403 311 4505 CERAMIC 1000P K 50V (N.S.P) C9027 403 311 4505 CERAMIC 1000P K 50V (N.S.P) C9028 403 346 2309 CERAMIC 0.1U K 10V (N.S.P) C9029 403 346 2309 CERAMIC 0.1U K 10V C9030 403 381 8106 CERAMIC 1U K 6.3V

(RESISTOR PACKS)

RB901 645 037 0830 R-NETWORK 47X4 1/32W (N.S.P) RB902 645 037 0830 R-NETWORK 47X4 1/32W (N.S.P) RB903 645 037 0830 R-NETWORK 47X4 1/32W (N.S.P)

(RESISTORS)

R9002 401 225 0200 MT-GLAZE 3.3K JA 1/16W (N.S.P) R9003 401 226 1503 MT-GLAZE 0.000 ZA 1/16W (N.S.P) R9004 401 225 0903 MT-GLAZE 82K JA 1/16W (N.S.P) R9005 401 226 1503 MT-GLAZE 0.000 ZA 1/16W (N.S.P) R9006 401 224 8900 MT-GLAZE 100K JA 1/16W (N.S.P) R9007 401 224 9402 MT-GLAZE 1.0M JA 1/16W (N.S.P) R9009 401 226 1503 MT-GLAZE 0.000 ZA 1/16W (N.S.P) R9010 401 240 9509 MT-GLAZE 820 JA 1/16W (N.S.P) R9011 401 240 9004 MT-GLAZE 3.9 JA 1/16W (N.S.P) R9012 401 224 9006 MT-GLAZE 10K JA 1/16W (N.S.P) R9013 401 285 1308 MT-GLAZE 1.3K JA 1/16W (N.S.P) R9014 401 225 1801 MT-GLAZE 47 JA 1/16W (N.S.P) R9015 401 234 4800 MT-GLAZE 3.3 JA 1/16W (N.S.P) R9016 401 234 4800 MT-GLAZE 3.3 JA 1/16W (N.S.P) R9019 401 226 1503 MT-GLAZE 0.000 ZA 1/16W (N.S.P) R9020 401 226 1503 MT-GLAZE 0.000 ZA 1/16W (N.S.P) R9021 401 226 1503 MT-GLAZE 0.000 ZA 1/16W (N.S.P) R9022 401 226 1503 MT-GLAZE 0.000 ZA 1/16W (N.S.P) R9023 401 226 1503 MT-GLAZE 0.000 ZA 1/16W (N.S.P) R9024 401 234 4800 MT-GLAZE 3.3 JA 1/16W (N.S.P)

R9025 401 234 4800 MT-GLAZE 3.3 JA 1/16W (N.S.P) R9027 401 226 1503 MT-GLAZE 0.000 ZA 1/16W (N.S.P) R9028 401 226 1503 MT-GLAZE 0.000 ZA 1/16W (N.S.P)

(CONNECTORS)

CN901 645 064 9936 SOCKT,PWB-PWB 50P (N.S.P)

645 066 1952 OPTICAL FILTER (N.S.P) 645 066 1990 LENS(ASSY),K196C (N.S.P) 409 593 6107 IC ICX488EQF-S (N.S.P) 411 170 4604 SCR TPG PAN PCS 1.4X3 (N.S.P) 636 069 2091 MOUNTING,LENS (N.S.P) 636 069 2329 SPRING COMP (N.S.P) 636 070 2134 SPACER (N.S.P)

COMPL PWB,TB-1

636 077 0799

(FILTERS)

XF651 645 053 4362 FILTER,EMI 1000000PF XF652 645 053 4362 FILTER,EMI 1000000PF

(INDUCTORS)

L6501 645 041 1977 INDUCTOR,330 OHM L6502 645 041 1977 INDUCTOR,330 OHM L6503 645 037 4340 INDUCTOR,1000 OHM L6504 645 037 4340 INDUCTOR,1000 OHM L6505 645 037 4340 INDUCTOR,1000 OHM

(FUSE)

F6501 423 031 1905 FUSE 32V 4A

(JACKS)

JK651 645 067 0367 SOCKET,DC 2P (N.S.P), TO DC JACK

(VARISTOR)

VA651 408 050 0504 VARISTOR AVR-M1005C080MT

(CONNECTORS)

CN651 645 054 4163 SOCKET,8P (N.S.P) CN652 645 067 3962 SOCKET,FPC 11P (N.S.P) CN653 645 059 0122 PLUG,PWB-WIRE 2P (N.S.P)

(MISCELLANEOUS)

636 078 4581 SPACER TB1-SX713/J

Z6501 645 051 6009 BATTERY,RECHARGE

COMPL PWB,TB-2

636 077 0805

(SWITCHES)

S6501 645 049 1108 SWITCH,PUSH 1P-1TX1,

(MISCELLANEOUS)

636 078 7957 ASSY,WIRE TB1-TB2-SX713

COMPL PWB,ST-1

636 077 0775

(SEMICONDUCTORS)

Q1431 405 168 3809 TR DTA144EM Q5001 405 163 3606 TR CPH3409 Q5002 405 181 1400 TR NSBC124EPDXV6T5 OR 405 173 3801 TR PEMD2 OR 405 165 1204 TR EMD2 Q5003 405 178 6807 TR MCH5809-TL-E Q5007 405 182 9009 TR EMF18 Q5009 405 115 5207 TR 2SC4617 R Q5011 405 183 4409 TR FDC606P Q5012 405 152 5406 TR 3LN01S-TL Q5015 405 178 6807 TR MCH5809-TL-E Q5016 405 182 9009 TR EMF18 Q5017 405 182 9009 TR EMF18 Q5402 406 017 6101 TR TND721MH5-TL-E Q5409 405 171 4800 TR CY25BAJ-8F Q9552 405 173 3702 TR FDC633N

(INTEGRATED CIRCUITS)

IC501 409 568 8006 IC MAX1566ETL+ IC541 409 573 4000 IC LT3468ES5 IC955 409 526 4002 IC XC9104D095M

(DIODES)

D5001 407 225 3609 DIODE HN2D01JE

Page 27

LOCATION PARTS NO. DESCRIPTIONLOCATION PARTS NO. DESCRIPTION LOCATION PARTS NO. DESCRIPTION

D5002 407 210 5403 DIODE RB551V-30 D5004 407 210 5403 DIODE RB551V-30 D5006 407 236 0802 ZENER DIODE EDZ2.0B D5007 407 232 3609 DIODE SD833-04SC D5008 407 210 5403 DIODE RB551V-30 D5401 407 223 5506 DIODE MA2Z720 D5402 407 235 3903 DIODE GSD2004S D5404 407 229 8709 DIODE CMC01 D9551 407 232 3609 DIODE SD833-04SC

(VARIABLE RESISTOR)

VR501 645 049 3232 VR,SEMI,10K S

(INDUCTORS)

L5001 645 061 7416 INDUCTOR,47U M L5002 645 061 7416 INDUCTOR,47U M L5003 645 061 7393 INDUCTOR,10U M L5004 645 059 1068 INDUCTOR,4.7U M L5005 645 052 5070 INDUCTOR,10U M L5006 645 052 5070 INDUCTOR,10U M L5007 645 056 6417 INDUCTOR,10U M L5009 645 056 6417 INDUCTOR,10U M L5015 645 041 1953 INDUCTOR,100 OHM L9551 645 058 0918 INDUCTOR,10U M

(TRANSFORMERS)

T5001 645 063 5014 TRANS,POWER,PULSE T5401 645 067 6710 TRANS,STEP UP T5402 645 060 1989 TRANS,STEP UP

(CAPACITORS)

C5001 403 314 7404 CERAMIC 3300P K 50V C5002 403 358 3202 CERAMIC 10U K 6.3V C5003 403 311 7704 CERAMIC 4700P K 25V C5004 403 314 7404 CERAMIC 3300P K 50V C5005 403 346 2309 CERAMIC 0.1U K 10V C5006 403 311 7704 CERAMIC 4700P K 25V C5007 403 319 3005 CERAMIC 220P J 25V C5008 403 314 7404 CERAMIC 3300P K 50V C5009 403 314 7404 CERAMIC 3300P K 50V C5011 403 358 3202 CERAMIC 10U K 6.3V C5012 403 381 1206 POS-SOLID 33U M 6.3V C5013 403 392 5002 CERAMIC 22U M 6.3V C5014 403 392 5002 CERAMIC 22U M 6.3V C5015 403 381 1206 POS-SOLID 33U M 6.3V C5016 403 358 3202 CERAMIC 10U K 6.3V C5017 403 358 3202 CERAMIC 10U K 6.3V C5031 403 325 0500 CERAMIC 2.2U K 16V C5032 403 379 6701 CERAMIC 10U K 16V C5033 403 340 6907 CERAMIC 1U K 16V C5034 403 341 4803 CERAMIC 10U K 10V C5035 403 358 3202 CERAMIC 10U K 6.3V C5037 403 358 3202 CERAMIC 10U K 6.3V C5041 403 325 0500 CERAMIC 2.2U K 16V C5043 403 325 0500 CERAMIC 2.2U K 16V C5044 403 379 0808 CERAMIC 1U M 16V C5045 403 343 3101 CERAMIC 1U K 6.3V C5046 403 343 3101 CERAMIC 1U K 6.3V C5401 403 378 3602 POS-SOLID 33U M 10V C5402 403 346 2309 CERAMIC 0.1U K 10V C5403 403 311 3409 CERAMIC 0.01U K 16V C5404 403 319 3609 CERAMIC 330P K 50V C5410 403 341 4407 CERAMIC 0.047U K 350V C5411 403 357 3302 CERAMIC 0.01U K 630V C9551 403 378 3602 POS-SOLID 33U M 10V C9553 403 381 1206 POS-SOLID 33U M 6.3V C9554 403 358 3202 CERAMIC 10U K 6.3V C9556 403 358 3202 CERAMIC 10U K 6.3V C9558 403 311 7506 CERAMIC 22P J 50V

(RESISTOR PACKS)

RB141 645 028 0719 R-NETWORK 10KX4 1/32W RB142 645 061 3661 R-NETWORK 10KX2 1/16W

(RESISTORS)

R5001 401 261 7904 MT-FILM 68K DD 1/16W R5002 401 261 8307 MT-FILM 39K DD 1/16W R5003 401 261 7607 MT-FILM 51K DD 1/16W R5004 401 258 0406 MT-GLAZE 120K DC 1/16W R5005 401 261 8802 MT-FILM 24K DD 1/16W R5006 401 261 7904 MT-FILM 68K DD 1/16W R5007 401 261 7508 MT-FILM 100K DD 1/16W R5008 401 226 1503 MT-GLAZE 0.000 ZA 1/16W

R5012 401 261 8703 MT-FILM 22K DD 1/16W R5013 401 261 9205 MT-FILM 13K DD 1/16W R5014 401 261 4804 MT-FILM 750 DU 1/16W R5019 401 261 8901 MT-FILM 27K DD 1/16W R5020 401 261 2404 MT-FILM 8.2K DU 1/16W R5021 401 261 4705 MT-FILM 680 DU 1/16W R5022 401 261 7102 MT-FILM 150 DU 1/16W R5027 401 261 8703 MT-FILM 22K DD 1/16W R5028 401 261 7706 MT-FILM 56K DD 1/16W R5029 401 261 2800 MT-FILM 5.1K DU 1/16W R5032 401 237 2407 MT-GLAZE 270K JA 1/16W R5033 401 224 9907 MT-GLAZE 22K JA 1/16W R5035 401 258 7009 MT-GLAZE 150K DC 1/16W R5036 401 261 9205 MT-FILM 13K DD 1/16W R5037 401 261 5504 MT-FILM 560 DU 1/16W R5038 401 262 0409 MT-FILM 56 DD 1/16W R5040 401 224 8900 MT-GLAZE 100K JA 1/16W R5041 401 224 9907 MT-GLAZE 22K JA 1/16W R5043 401 224 9907 MT-GLAZE 22K JA 1/16W R5044 401 224 8900 MT-GLAZE 100K JA 1/16W R5045 401 258 9300 MT-GLAZE 220K DC 1/16W R5046 401 261 9502 MT-FILM 18K DD 1/16W R5047 401 262 3004 MT-FILM 27 DD 1/16W R5048 401 262 3004 MT-FILM 27 DD 1/16W R5049 401 226 1503 MT-GLAZE 0.000 ZA 1/16W R5050 401 258 7009 MT-GLAZE 150K DC 1/16W R5051 401 261 9205 MT-FILM 13K DD 1/16W R5052 401 261 5603 MT-FILM 620 DU 1/16W R5053 401 262 3608 MT-FILM 18 DD 1/16W R5054 401 261 8109 MT-FILM 33K DD 1/16W R5056 401 224 9006 MT-GLAZE 10K JA 1/16W R5057 401 224 9006 MT-GLAZE 10K JA 1/16W R5058 401 241 0000 MT-GLAZE 1.8M JA 1/16W R5059 401 224 9006 MT-GLAZE 10K JA 1/16W R5060 401 226 1503 MT-GLAZE 0.000 ZA 1/16W R5063 401 224 8900 MT-GLAZE 100K JA 1/16W R5064 401 261 8109 MT-FILM 33K DD 1/16W R5065 401 224 9006 MT-GLAZE 10K JA 1/16W R5073 401 226 1503 MT-GLAZE 0.000 ZA 1/16W R5401 401 261 2602 MT-FILM 10K DU 1/16W R5402 401 224 9006 MT-GLAZE 10K JA 1/16W R5403 401 224 9303 MT-GLAZE 1K JA 1/16W R5404 401 227 2400 MT-GLAZE 15 JA 1/16W R5422 402 079 0200 MT-GLAZE 220K JKG 1/8W R5423 401 226 1503 MT-GLAZE 0.000 ZA 1/16W R5425 402 077 7409 MT-GLAZE 100K JKG 1/8W R5426 401 224 9006 MT-GLAZE 10K JA 1/16W R9551 401 261 4705 MT-FILM 680 DU 1/16W R9552 401 299 4005 MT-GLAZE 510K DC 1/16W R9553 401 258 0406 MT-GLAZE 120K DC 1/16W

(FUSES)

F5001 423 031 1806 FUSE 32V 2.5A F5002 423 031 1806 FUSE 32V 2.5A F5003 423 031 1707 FUSE 32V 2A F5004 423 031 1509 FUSE 32V 1A F5005 423 031 1707 FUSE 32V 2A

(CONNECTORS)

CN143 645 068 2278 SOCKET,CARD(SD) (N.S.P.) CN501 645 064 9929 PLUG,PWB-PWB 50P (N.S.P)

(MISCELLANEOUS)

636 076 5115 COMPL,REFLECTOR SX713 636 079 6126 ASSY,WIRE JW501&651-SX713 (N.S.P.) 636 076 5849 ASSY,WIRE JW502&652-SX713 (N.S.P.)

COMPL PWB,ST-2

636 077 0782

(CAPACITOR)

C5412 404 096 3707 ELECT 80U A 300V

(MISCELLANEOUS)

636 079 6102 ASSY,WIRE FLC+ (N.S.P.) 636 079 6119 ASSY,WIRE FLC- (N.S.P.)

Page 28

Mar./’04

SANYO Electric Co., Ltd. Osaka, Japan