Sanyo PDG-DSU20E, PDG-DSU20B, PDG-DSU20N User Manual
Multimedia Projector
Projecteur Multimédia
Multimedia-Projektor
Proyector Multimedia
Proiettore Multimediale
Owner's Manual/Mode d'emploi/
Bedienungsanleitung/Manual del usuario/
Manuale d'uso
MODEL/MODÈLE/MODELO/MODELL/MODELLO
PDG-DSU20N/DSU20E/DSU20B
To the Owner
1
SIDE and TOP
REAR
90 cm 30 cm 30 cm
Before operating this projector, read this manual
thoroughly and operate the projector properly.
This projector provides many convenient
features and functions. Operating the projector
properly enables you to manage those features
and maintains it in better condition for a
considerable time.
Improper operation may result in not only shortening
the product-life, but also malfunctions, fire
hazard, or other accidents.
If your projector seems to operate improperly,
read this manual again, check operations and
cable connections and try the solutions in the
"Troubleshooting" section in the end of this
booklet. If the problem still persists, contact
the dealer where you purchased the projector
or the service center.
Safety Precaution
WARNING: TO REDUCE THE RISK OF FIRE
OR ELECTRIC SHOCK, DO NOT EXPOSE
THIS APPLIANCE TO RAIN OR MOISTURE.
- This projector produces intense light from
the projection lens. Do not stare directly
into the lens, otherwise, eye damage could
result. Be especially careful that children
do not stare directly into the beam.
- Install the projector in a proper position. If
not, it may result in a fire hazard.
- Provide appropriate space on the top,
sides and rear of the projector cabinet for
allowing air circulation and cooling
projector. Minimum clearance must be
maintained. If the projector is to be built into a
compartment or similarly
minimum distances must be maintained.
not cover the ventilation slot on the
projector. Heat build-up can reduce the
service life of your projector, and can also
be dangerous.
5 cm
- If the projector is not to be used for an
extended time, unplug the projector from
the power outlet.
enclosed, the
the
Do
READ AND KEEP THIS OWNER’S MANUAL
FOR LATER USE.
EN-1
CAUTION
DO NOT SET THE PROJECTOR IN
GREASY, WET, OR SMOKY CONDITIONS
SUCH AS IN A KITCHEN TO PREVENT A
BREAKDOWN OR A DISASTER. IF THE
PROJECTOR COMES IN CONTACT WITH
OIL OR CHEMICALS, IT MAY BECOME
DETERIORATED.
NOTE: This symbol and recycle system are applied to EU
countres only and not applied to the countries in the
other area of the world.
Your SANYO product is designed
and manufactured with high
quality materials and components
which can be recycled and
reused.
This symbol means that electrical
and electronic equipment, at their
end-of-life, should be disposed of
separately from your household
waste.
Please dispose of this equipment at your local
community waste collection/recycling centre. In
the European Union there are separate
collection systems for used electrical and
electronic products.
Please help us to conserve the environment we
live in!
CAUTION
Not for use in a computer room as defined in the
Standard for the Protection of Electronic
Computer/Data Processing Equipment, ANSI/
NFPA 75.
Ne peut
être utilisé dans une salle d’ordinateurs
telle que d
Standard for Protection of Electronic Computer/
Data Processing Electronic.
éfinie dans la norme ANSI/NFPA 75
Notes on Litium Battery (CARIFORNIA
USA ONLY)
This product uses a Litium Battery which contains
Perchlorate Material - special handling may apply.
See www.dtsc.ca.gov/hazardouswaste/perchlorate.
Notas acerca de pilas de Litio (SOLO
CARIFORNIA, EE.UU.)
Este producto usa una pila de litio que contiene
el material perclorato - puede ser necesario una
manipulati
Consulte la p
www.dtsc.ca.gov/hazardouswaste/perchlorate.
ó
n especial.
á
gina
Voor de klanten in Nederland
Bij dit produkt zijn batterijen geleverd.
Wanneer deze leeg zijn, moet u ze niet
weggooien maar inleveren als KCA.
NL
SANYO FISHER Sales (Europe) GmbH
Stahlgruberring 4, D-81829 München,
Germany
SANYO Electric Co., Ltd.
1-1, Sanyo-cho, Daito City, Osaka 574-8534,
Japan
EN-2
Safety Instructions
All the safety and operating instructions should be
read before the product is operated.
Read all of the instructions given here and retain
them for later use. Unplug this projector from AC
power supply before cleaning. Do not use liquid or
aerosol cleaners. Use a damp cloth for cleaning.
Follow all warnings and instructions marked on
the projector.
For added protection to the projector during a
lightning storm, or when it is left unattended and
unused for long periods of time, unplug it from the
wall outlet. This will prevent damage due to
lightning and power line surges.
Do not expose this unit to rain or use near
water... for example, in a wet basement, near a
swimming pool, etc...
Do not use attachments not recommended by the
manufacturer as they may cause hazards.
Do not place this projector on an unstable cart,
stand, or table. The projector may fall, causing
serious injury to a child or adult, and serious
damage to the projector. Use only with a cart or
stand recommended by the manufacturer, or sold
with the projector. Wall or shelf mounting should
follow the manufacturer's instructions, and should
use a mounting kit approved by the manufacturers.
An appliance and cart
combination should be moved
with care. Quick stops,
excessive force, and uneven
surfaces may cause the
appliance and cart combination
to overturn.
Slots and openings in the back and bottom of the
cabinet are provided for ventilation, to ensure
reliable operation of the equipment and to protect
it from overheating.
The openings should never be covered with cloth
or other materials, and the bottom opening
should not be blocked by placing the projector on
a bed, sofa, rug, or other similar surface. This
projector should never be placed near or over a
radiator or heat register.
This projector should not be placed in a built-in
installation such as a book case unless proper
ventilation is provided.
Never push objects of any kind into this projector
through cabinet slots as they may touch
dangerous voltage points or short out parts that
could result in a fire or electric shock. Never spill
liquid of any kind on the projector.
Do not install the projector near the ventilation
duct of air-conditioning equipment.
This projector should be operated only from the
type of power source indicated on the marking
label. If you are not sure of the type of power
supplied, consult your authorized dealer or local
power company.
Do not overload wall outlets and extension cords
as this can result in fire or electric shock. Do not
allow anything to rest on the power cord. Do not
locate this projector where the cord may be
damaged by persons walking on it.
Do not attempt to service this projector yourself
as opening or removing covers may expose you
to dangerous voltage or other hazards. Refer all
servicing to qualified service personnel.
Unplug this projector from wall outlet and refer
servicing to qualified service personnel under the
following conditions:
a When the power cord or plug is damaged or
frayed.
b If liquid has been spilled into the projector.
c If the projector has been exposed to rain or
water.
d If the projector does not operate normally by
following the operating instructions. Adjust only
those controls that are covered by the operating
instructions as improper adjustment of other
controls may result in damage and will often
require extensive work by a qualified technician
to restore the projector to normal operation.
e If the projector has been dropped or the cabinet
has been damaged.
f When the projector exhibits a distinct change in
performance-this indicates a need for service.
When replacement parts are required, be sure the
service technician has used replacement parts
specified by the manufacturer that have the same
characteristics as the original part. Unauthorized
substitutions may result in fire, electric shock, or
injury to persons.
Upon completion of any service or repairs to this
projector, ask the service technician to perform
routine safety checks to determine that the
projector is in safe operating condition.
EN-3
Air Circulation
Openings in the cabinet are provided for
ventilation and to ensure reliable operation of
the product and to protect it from overheating,
and these openings must not be blocked or
covered.
CAUTION
Hot air is exhausted from the exhaust vent.
When using or installing the projector, the
following precautions should be taken.
- Do not put any flammable object or spray
can near the projector, hot air is exhausted
from the ventilation holes.
- Keep the exhaust vent at least 90 cm away
from any objects.
- Do not touch a peripheral part of the
exhaust vent, especially screws and
metallic part. This area will become hot
while the projector is being used.
- Do not put anything on the cabinet.
Objects put on the cabinet will not only get
damaged but also cause fire hazard by
heat.
Cooling fans are provided to cool down the
projector. The fans’ running speed is changed
according to the temperature inside the
projector.
Installing the Projector in Proper Position
Install the projector properly. Improper
Installation may reduce the lamp life and
cause a fire hazard.
Do not tilt the projector sideways.
Do not point the projector up to
project an image.
Do not point the projector down
to project an image.
Do not put the projector on
either side to project an image.
6˚
6˚
Do not pitch the projector more
than 6 degrees backward and
forward.
Moving the Projector
When moving the projector, replace the lens
cap and retract the elevator foot to prevent
damage to the lens and cabinet. When the
projector is not in use for an extended period,
put it into a suitable case with the lens side up
to protect the projector.
When handling the projector, do not drop,
bump, subject it to strong forces, or put other
things on the cabinet.
EN-4
USE CAUTION IN CARRYING OR
TRANSPORTING THE PROJECTOR
- Do not drop or bump the projector,
otherwise damages or malfunctions may
result.
- When carrying the projector, use a suitable
carrying case.
- Do not transport the projector by using a
courier or transport service in an unsuitable
transport case. This may cause damage to
the projector. To transport the projector
through a courier or transport service,
consult your dealer for their information.
- Do not put the projector in a case before
the projector is cooled enough.
Compliance
Federal Communications Commission Notice
Note: This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses, and can
radiate radio frequency energy, and if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Use of shielded cable is required to comply with class B limits in Subpart B of Part 15 of FCC Rules.Do
not make any changes or modifications to the equipment unless otherwise specified in the instructions.
If such changes or modifications should be made, you could be required to stop operation of the equipment.
Model Number: PDG-DSU20N
Trade Name: Sanyo
Responsible party: SANYO FISHER COMPANY
Address: 21605 Plummer Street, Chatsworth, California 91311
Telephone No.: (818)998-7322
The AC Power Cord supplied with this projector meets the requirement for use in the country you
purchased it.
AC Power Cord for the United States and Canada:
AC Power Cord used in the United States and Canada is listed by the
Underwriters Laboratories (UL) and certified by the Canadian Standard
Association (CSA).AC Power Cord has a grounding-type AC line plug. This is
a safety feature to be sure that the plug will fit into the power outlet. Do not try
to defeat this safety feature. Should you be unable to insert the plug into the
outlet, contact your electrician.
AC Power Cord for the United Kingdom:
This cord is already fitted with a moulded plug
incorporating a fuse, the value of which is
indicated on the pin face of the plug. Should the
fuse need to be replaced, an ASTA approved BS
1362 fuse must be used of the same rating,
marked thus . If the fuse cover is detachable,
never use the plug with the cover omitted. If a
replacement fuse cover is required, ensure it is of
the same colour as that visible on the pin face of
the plug (i.e. red or orange). Fuse covers are
available from the Parts Department indicated in
your User Instructions.
If the plug supplied is not suitable for your socket
outlet, it should be cut off and destroyed.
The end of the flexible cord should be suitably
prepared and the correct plug fitted.
WARNING : A PLUG WITH BARED FLEXIBLE
CORD IS HAZARDOUS IF ENGAGED IN A
LIVE SOCKET OUTLET.
THE SOCKET-OUTLET SHOULD BE INSTALLED NEAR THE EQUIPMENT AND EASILY
ACCESSIBLE.
ASA
AC Power Cord Requirement
The Wires in this mains lead are coloured in
accordance with the following code:
Green-and-yellow .....Earth
Blue ..........................Neutral
Brown .......................Live
As the colours of the wires in the mains lead of
this apparatus may not correspond with the
coloured markings identifying the terminals in
your plug proceed as follows:
The wire which is coloured green-and-yellow must
be connected to the terminal in the plug which is
marked by the letter E or by the safety earth
symbol or coloured green or green-and-yellow.
The wire which is coloured blue must be
connected to the terminal which is marked with
the letter N or coloured black.
The wire which is coloured brown must be
connected to the terminal which is marked with
the letter L or coloured red.
WARNING: THIS APPARATUS MUST BE EARTHED.
GROUND
EN-5
Notes on the AC Power Cord
AC Power Cord must meet the requirement of countries where you use this projector. Please
confirm your AC plug type with the graphics below and ensure that the proper AC Power Cord is
used. If the supplied AC Power Cord does not match your AC outlet, please contact your sales
dealer. This projector is equipped with a grounding type AC line plug. Please ensure that your
outlet fits the plug. Do not defeat the safety purpose of this grounding type plug. We highly
recommend using a video source device also equipped with a grounding type AC line plug to
prevent signal interference due to voltage fluctuations.
Ground
EN-6
CONTENTS
CONTENTS .......................................................................................................................... 7
Introduction .........................................................................................................................8
Projector Features .......................................................................................................................8
Package Contents .......................................................................................................................9
Projector Overview ....................................................................................................................10
Using the Product ........................................................................................................12
Control Panel .............................................................................................................................12
Connection Ports .......................................................................................................................13
Remote Control ..........................................................................................................................14
Replacing the Battery ................................................................................................................15
Remote Control Operation .........................................................................................................16
Installation ..........................................................................................................................17
Connecting the Projector ...........................................................................................................17
Powering On/Off the Projector ...................................................................................................18
Adjusting the Projector ...............................................................................................................19
Menu Operation ..............................................................................................................21
Maintenance ....................................................................................................................25
Cleaning the Lens ......................................................................................................................25
Cleaning the Projector Housing .................................................................................................25
Replacing the Lamp ...................................................................................................................26
Specifications ................................................................................................................28
Appendix ............................................................................................................................ 29
LED Indicator Messages ............................................................................................................29
Compatibility Modes ..................................................................................................................30
Troubleshooting .........................................................................................................................31
EN-7
Introduction
Projector Features
The projector integrates high-performance optical engine projection and a user - friendly
deliver high reliability and ease of use.
The projector offers the following features:
Single chip 0.55" Texas Instruments DLP
®
technology
SVGA (800 x 600 pixels)
Auto image re-sizing (Auto-Sync.) to 800 x 600 full screen with scaling compression
compatibility for VGA, SVGA, XGA* and SXGA*
Compatibility with Macintosh
®
computers
Compatibility with NTSC, PAL, SECAM and HDTV
D-Sub 15-pin terminal for analog video connectivity
User-friendly, multi-language on-screen display
Advanced electronic keystone correction
* means compressed.
DLP is a registered trademark of Texas Instruments.
design to
EN-8
Package Contents
When you unpack the projector, make sure you have all these components:
Projector with Lens Cap AC Power Cord
(USA: J2552-0109-00) (UK: J2552-0108-00) (J2552-0072-03)
(Europe: J2552-0107-00)
Remote Control (IR) Owner’s Manual Quick Start Guide
Save the original shipping carton and packing material; they will comein handy if you
ever to ship your unit. For maximum protection, repack your unit as it was originally
packed at the factory.
Accessories and components may vary by retailer and region.
VGA Cable (D-SUB to D-SUB)
EN-9
Loading...